此产品的文档集力求使用非歧视性语言。在本文档集中,非歧视性语言是指不隐含针对年龄、残障、性别、种族身份、族群身份、性取向、社会经济地位和交叉性的歧视的语言。由于产品软件的用户界面中使用的硬编码语言、基于 RFP 文档使用的语言或引用的第三方产品使用的语言,文档中可能无法确保完全使用非歧视性语言。 深入了解思科如何使用包容性语言。
思科采用人工翻译与机器翻译相结合的方式将此文档翻译成不同语言,希望全球的用户都能通过各自的语言得到支持性的内容。 请注意:即使是最好的机器翻译,其准确度也不及专业翻译人员的水平。 Cisco Systems, Inc. 对于翻译的准确性不承担任何责任,并建议您总是参考英文原始文档(已提供链接)。
NCS6K与传统IOS-XR平台有一个关键区别:NCS6K利用虚拟化技术构建系统。每个节点(路由处理器(RP)或线卡(LC))可以运行多个虚拟机(VM),如系统管理VM、IOS-XR VM1、IOS-XR VM2等,这些节点结合在一起可创建一个功能齐全的XR节点。下图显示RP和LC运行一个IOS-XR VM的示例:
图 1
有一个控制以太网网络来连接RP和LC。RP和LC之间的控制平面流量将通过此控制以太网网络。由于这是虚拟化环境,因此会出现以下问题:如何将这些数据包传送到特定虚拟机,以及RP或LC中的Nicantic(NIC)如何知道发往它们的数据包?
简而言之,VLAN用于区分不同虚拟机的流量,此过程由NIC完成。图2显示NIC如何将VLAN 3074流量传送到IOS-XR虚拟机,将VLAN 3073流量传送到管理VM。
图 2
将这些转发组件组合在一起,您可以获得用于ping测试场景的简化转发路径,如图3所示。
从RP执行ping测试时,数据包在机箱内采用以下转发路径:
RP_PING <—> RP_NETIO <—> RP_SPP <—> RP_Linux_Kernel_Socket <—>交换机<—> LC_FIA <—> LC_NPU(包括PSE、PLIM_ASIC)<—>线路
图 3
在本文档的其余部分,将以从RP发起ping的场景为例。将向Te0/0/0/2/0上的直连主机发起ping操作。以下步骤将逐步显示验证此ping数据包路径的方法。
RP/0/RP0/CPU0:NCS6k-Deploy#show ip interface brief Interface IP-Address Status Protocol Bundle-Ether671 10.67.2.2 Up Up Bundle-Ether672 10.67.3.2 Down Down Loopback0 10.17.17.17 Up Up MgmtEth0/RP0/CPU0/0 10.7.54.11 Up Up TenGigE0/0/0/2/0 10.67.1.2 Up Up TenGigE0/0/0/2/1 unassigned Up Up TenGigE0/0/0/2/2 unassigned Up Up TenGigE0/0/0/2/3 unassigned Up Up TenGigE0/0/0/2/4 unassigned Up Up TenGigE0/0/0/2/5 unassigned Down Down [snip] RP/0/RP0/CPU0:NCS6k-Deploy#show run interface Ten 0/0/0/2/0 interface TenGigE0/0/0/2/0 ipv4 address 10.67.1.2 255.255.255.252 load-interval 30 RP/0/RP0/CPU0:NCS6k-Deploy#ping 10.67.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.67.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 5/6/7 ms
RP节点上的“show IPv4 traffic”计数器将显示已发送的互联网控制消息协议(ICMP)回应数和已返回的ICMP应答数。
RP/0/RP0/CPU0:NCS6k-Deploy#show ipv4 traffic
IP statistics:
Rcvd: 1495334 total, 80112 local destination
0 format errors, 0 bad hop count
23 unknown protocol, 0 not a gateway
0 security failures, 0 bad source, 0 bad header
133207 with options, 0 bad, 0 unknown
Opts: 0 end, 0 nop, 0 basic security, 0 extended security
0 strict source rt, 0 loose source rt, 0 record rt
0 stream ID, 0 timestamp, 133207 alert, 0 cipso
Frags: 0 reassembled, 0 timeouts, 0 couldn't reassemble, 0 fragments received
0 fragmented, 0 fragment count, 0 fragment max drop
Bcast: 0 sent, 0 received
Mcast: 1361652 sent, 1376283 received
Drop: 0 encapsulation failed, 237 no route, 0 too big
Sent: 1437435 total
ICMP statistics:
Sent: 0 admin unreachable, 63 network unreachable
8 host unreachable, 0 protocol unreachable
16 port unreachable, 0 fragment unreachable
0 time to live exceeded, 0 reassembly ttl exceeded
24 echo request, 30024 echo reply
0 mask request, 0 mask reply
0 parameter error, 0 redirects
30131 total
Rcvd: 0 admin unreachable, 21 network unreachable
0 host unreachable, 0 protocol unreachable
0 port unreachable, 0 fragment unreachable
0 time to live exceeded, 0 reassembly ttl exceeded
30024 echo request, 15 echo reply
0 mask request, 0 mask reply
0 redirect, 0 parameter error
0 source quench, 0 timestamp, 0 timestamp reply
0 router advertisement, 0 router solicitation
30063 total, 0 checksum errors, 0 unknown
检查网络输入输出(NETIO)组件。
下一步是检查RP FINT NETIO链计数器。您必须看到网络链中IPv4节点的“OUT”计数器。如果增加,则意味着数据包已到达NETIO组件,并正从NETIO组件发出。
Check initial NETIO counter value.
RP/0/RP0/CPU0:NCS6k-Deploy#sh netio chains FINT loc 0/rp0/cpu0 | in Stats <Protocol number> (name) Stats <6> (fint_n2n) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <10> (clns) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <12> (ipv4) Stats IN: 2788 pkts, 115373 bytes; OUT: 2816 pkts, 117933 bytes <13> (mpls) Stats IN: 16482 pkts, 2467508 bytes; OUT: 0 pkts, 0 bytes <18> (lpts) Stats IN: 47234 pkts, 10381065 bytes; OUT: 0 pkts, 0 bytes <19> (ipv6) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <30> (ipv4_preroute) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <32> (ipv6_preroute) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <34> (fint_proto_tp) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <36> (l2transport) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes
Initiate 10 ping packets.
RP/0/RP0/CPU0:NCS6k-Deploy#ping 10.67.1.1 coun 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 10.67.1.1, timeout is 2 seconds: !!!!!!!!!! Success rate is 100 percent (10/10), round-trip min/avg/max = 4/7/8 ms
Check NETIO counter again. You would see increment of 10 packets.
RP/0/RP0/CPU0:NCS6k-Deploy#sh netio chains FINT loc 0/rp0/cpu0 | in Stats <Protocol number> (name) Stats <6> (fint_n2n) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <10> (clns) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <12> (ipv4) Stats IN: 2788 pkts, 115373 bytes; OUT: 2826 pkts, 118933 bytes <13> (mpls) Stats IN: 16482 pkts, 2467508 bytes; OUT: 0 pkts, 0 bytes <18> (lpts) Stats IN: 47234 pkts, 10381065 bytes; OUT: 0 pkts, 0 bytes <19> (ipv6) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <30> (ipv4_preroute) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <32> (ipv6_preroute) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <34> (fint_proto_tp) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes <36> (l2transport) Stats IN: 0 pkts, 0 bytes; OUT: 0 pkts, 0 bytes
您还可以使用KornShell(ksh)命令“show_netio_fwder_stats -g”检查注入/punt计数器是否增加。
注意:在生产环境中,可能存在其他后台流量,这使得很难检查ping数据包是否到达此组件。解决方法是,可以使用超时为0的大量数据包:“ping x.x.x.x count 10000 time 0”并检查计数器是突然增加还是出现峰值。
Check initial counter value.
RP/0/RP0/CPU0:NCS6k-Deploy#run show_netio_fwder_stats -g RECEIVE STATISTICS SUMMARY: rx_pkts: 2224455 punt_pkts: 2224447 ingress_total_drops: 8 TRANSMIT STATISTICS SUMMARY: inject_pkts: 2077319 tx_pkts: 2058041 egress_total_drops: 2 RECEIVE STATISTICS DETAILS: Rx Pkt type stats: lpts_pkts: 2220753 Rx Listener tag stats: ipv4: 1116092 ipv6: 658627 clns: 112549 ipv4_l: 286252 raw4: 23 raw6: 43984 ospf_mc4: 45 ospf_mc6: 2 udp4: 7 tcp4: 405 isis: 2767 Rx Punt reason stats: IFIB: 2220753 Rx Drop stats: null_fint_ifh_drops: 8 ingress_total_drops: 8 TRANSMIT STATISTICS DETAILS: Tx Pkt type stats: ipv4: 2852 mpls: 42647 osi: 78760 ipv4_preroute: 1339401 ipv6_preroute: 613659 Tx Protocol Id stats: clns: 78760 ipv4: 2852 mpls: 42647 ipv4_preroute: 1339401 ipv6_preroute: 613659 Tx Drop stats: invalid_queue_drops: 2 hdr_init_drops: 2 egress_total_drops: 2
Initiate 10 ping packets.
RP/0/RP0/CPU0:NCS6k-Deploy#ping 10.67.1.1 coun 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 10.67.1.1, timeout is 2 seconds: !!!!!!!!!! Success rate is 100 percent (10/10), round-trip min/avg/max = 3/4/7 ms
Check counter again to check to se increment of 10 packets.
RP/0/RP0/CPU0:NCS6k-Deploy#run show_netio_fwder_stats -g RECEIVE STATISTICS SUMMARY: rx_pkts: 2224465 punt_pkts: 2224457 ingress_total_drops: 8 TRANSMIT STATISTICS SUMMARY: inject_pkts: 2077332 tx_pkts: 2058051 egress_total_drops: 2 RECEIVE STATISTICS DETAILS: Rx Pkt type stats: lpts_pkts: 2220763 Rx Listener tag stats: ipv4: 1116102 ipv6: 658627 clns: 112549 ipv4_l: 286252 raw4: 23 raw6: 43984 ospf_mc4: 45 ospf_mc6: 2 udp4: 7 tcp4: 405 isis: 2767 Rx Punt reason stats: IFIB: 2220763 Rx Drop stats: null_fint_ifh_drops: 8 ingress_total_drops: 8 TRANSMIT STATISTICS DETAILS: Tx Pkt type stats: ipv4: 2865 mpls: 42647 osi: 78760 ipv4_preroute: 1339401 ipv6_preroute: 613659 Tx Protocol Id stats: clns: 78760 ipv4: 2865 mpls: 42647 ipv4_preroute: 1339401 ipv6_preroute: 613659 Tx Drop stats: invalid_queue_drops: 2 hdr_init_drops: 2 egress_total_drops: 2 RP/0/RP0/CPU0:NCS6k-Deploy#
检查SPP组件。
使用SPP CLI查看数据包是否到达SPP。
Check initial counter value.
RP/0/RP0/CPU0:NCS6k-Deploy#sh spp node-counters 0/0/CPU0: pdma/rx slice1 high pkts: 10 ------------------------------- pdma/tx slice1 low pkts: 10 ------------------------------- panini/classify forwarded to spp clients: 10 ------------------------------- client/inject pkts injected into spp: 10 ------------------------------- client/punt punted to client: 10 ------------------------------- 0/RP0/CPU0: panini/classify forwarded to spp clients: 22070 ------------------------------- client/inject pkts injected into spp: 4640 ------------------------------- socket/rx ce low pkts: 45 mgmt interface pkts: 22025 ------------------------------- socket/tx ce pkts: 45 mgmt interface pkts: 4595 ------------------------------- client/punt punted to client: 22070 -------------------------------
Initiate 100 ping packets.
RP/0/RP0/CPU0:NCS6k-Deploy#ping 10.67.1.1 count 100 Type escape sequence to abort. Sending 100, 100-byte ICMP Echos to 10.67.1.1, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Success rate is 100 percent (100/100), round-trip min/avg/max = 3/3/8 ms
Check counter again to see increment of 100 packets.
RP/0/RP0/CPU0:NCS6k-Deploy#sh spp node-counters 0/0/CPU0: pdma/rx slice1 high pkts: 10 ------------------------------- pdma/tx slice1 low pkts: 10 ------------------------------- panini/classify forwarded to spp clients: 10 ------------------------------- client/inject pkts injected into spp: 10 ------------------------------- client/punt punted to client: 10 ------------------------------- 0/RP0/CPU0: panini/classify forwarded to spp clients: 22172 ------------------------------- client/inject pkts injected into spp: 4740 ------------------------------- socket/rx ce low pkts: 145 mgmt interface pkts: 22027 ------------------------------- socket/tx ce pkts: 145 mgmt interface pkts: 4595 ------------------------------- client/punt punted to client: 22172 -------------------------------
使用tcpdump工具转储来自Linux内核组件的数据包。
从以下输出中,在NCS6K XR VM ksh下,您可以看到几个子接口:
RP/0/RP0/CPU0:NCS6008-SJ# RP/0/RP0/CPU0:NCS6008-SJ#run Tue Jun 24 10:51:51.972 UTC [xr-vm_node0_RP0_CPU0:/]$ [xr-vm_node0_RP0_CPU0:/]$ ifconfig -a eth-vf1 Link encap:Ethernet HWaddr 46:91:EE:A5:48:A8 inet6 addr: fe80::4491:eeff:fea5:48a8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9700 Metric:1 RX packets:518403076C3 errors:0 dropped:0 overruns:0 frame:0 TX packets:969599306 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:138405352234 (128.9 GiB) TX bytes:242828863250 (226.1 GiB) eth-vf1.514 Link encap:Ethernet HWaddr 4C:4E:35:B6:63:68 inet6 addr: fe80::4e4e:35ff:feb6:6368/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9700 Metric:1 RX packets:13547000 errors:0 dropped:0 overruns:0 frame:0 TX packets:116957 errors:0 dropped:10 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:623478135C3 (594.5 MiB) TX bytes:26876899 (25.6 MiB) eth-vf1.3073 Link encap:Ethernet HWaddr 4C:4E:35:B6:63:69 inet addr:192.0.0.4 Bcast:192.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::4e4e:35ff:feb6:6369/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9700 Metric:1 RX packets:102364757 errors:0 dropped:0 overruns:0 frame:0 TX packets:100689507 errors:0 dropped:3 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:29925046692 (27.8 GiB) TX bytes:7562528012 (7.0 GiB) eth-vf1.3074 Link encap:Ethernet HWaddr 4E:41:50:00:10:01 inet addr:172.0.16.1 Bcast:172.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::4c41:50ff:fe00:1001/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9700 Metric:1 RX packets:402491385 errors:0 dropped:0 overruns:0 frame:0 TX packets:350389778 errors:0 dropped:6 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:100599198478 (93.6 GiB) TX bytes:96834116492 (90.1 GiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1029861486 errors:0 dropped:0 overruns:0 frame:0 TX packets:1029861486 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:201624257033 (187.7 GiB) TX bytes:201624257033 (187.7 GiB)
eth-vf1.514用于与Mgmtehter接口通信,但您看不到IPv4地址。XR VM中的Mgmtether接口依赖于IOS-XR的IP堆栈,而不是Linux中的IP堆栈。
ether-vf1.3073用于与管理VM通信。
eher-vf1.3074用于XR VM相关控制平面流量。Ping测试数据包将通过此子接口(使用Linux网络协议栈)。
与Linux关联的Tcpdump在如何转储相关流量方面有许多选项。此外,您可以使用tcpdump工具嗅探安全域路由器(SDR)控制平面流量(vlan 3074)或嗅探VLAN 3073中的进程间通信(IPC)通信等其他流量。
xr-vm_node0_RP0_CPU0:/]$ tcpdump -i eth-vf1.3074 -XX -vv tcpdump: listening on eth-vf1.3074, link-type EN10MB (Ethernet), capture size 65535 bytes 01:49:21.798386 IP (tos 0x6,ECT(0), ttl 1, id 0, offset 0, flags [DF], proto UDP (17), length 340) 172.0.16.1.10150 > 239.255.0.4.10150: [bad udp cksum ab2a!] UDP, length 312 0x0000: 0100 5e7f 0004 4e41 5000 1001 0800 4506 ..^...NAP.....E. 0x0010: 0154 0000 4000 0111 cc8e ac00 1001 efff .T..@........... 0x0020: 0004 27a6 27a6 0140 ad56 abcd abcd 0000 ..'.'..@.V...... 0x0030: 0000 0280 f502 0000 0000 0000 0000 0000 ................ 0x0040: 0000 0000 0000 7856 3412 0128 0204 0000 ......xV4..(.... 0x0050: 0000 5508 0100 0100 0000 3c25 2600 0000 ..U.......<%&... 0x0060: 0000 d007 0000 0000 0000 ffff 0000 0000 ................ 0x0070: 0000 0000 0000 0000 0000 0000 0000 0000 ................ 0x0080: 0000 0000 0000 4800 0000 0200 0000 0000 ......H......... 0x0090: 0000 8800 0000 0000 0000 0000 0000 0000 ................ 0x00a0: 0000 0100 0000 0000 0000 0000 0000 0000 ................ 0x00b0: 0000 0000 0000 c2ca 0031 0000 0000 0000 .........1...... 0x00c0: 0000 0000 0000 0000 0000 5508 0000 6510 ..........U...e. 0x00d0: 0000 ed53 4c00 0000 0000 0000 0000 0000 ...SL........... 0x00e0: 0000 0000 0000 0000 0000 0000 0000 6264 ..............bd 0x00f0: 7863 0000 0000 0000 0000 0000 0000 0000 xc.............. 0x0100: 0000 0000 0000 0000 0000 0000 0000 0000 ................ 0x0110: 0000 0100 0000 0000 0000 0000 0000 30ff ..............0. 0x0120: 0002 0000 0000 0000 0000 0000 0000 0000 ................ 0x0130: 0000 0000 0000 0000 0000 0000 0000 0000 ................ 0x0140: 0000 0000 0000 0000 0000 0c00 0000 0000 ................ 0x0150: 0000 0000 0000 0000 0000 0000 0000 0000 ................ 0x0160: 0000 .. 01:49:21.799167 IP (tos 0x6,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto UDP (17), length 380) 172.0.0.1.8197 > 172.0.16.1.8197: [udp sum ok] UDP, length 352 0x0000: 4e41 5000 1001 4e41 5000 0001 0800 4506 NAP...NAP.....E. 0x0010: 017c 0000 4000 4011 d168 ac00 0001 ac00 .|..@. 0x0040: 0000 0000 0000 7856 3412 0128 0204 0000 ......xV4..(.... 0x0050: 0000 5508 0100 0100 0000 3d25 2600 0000 ..U.......=%&... 0x0060: 0000 d007 0000 0000 0000 ffff 0000 0000 ................ 0x0070: 0000 0000 0000 0000 0000 0000 0000 0000 ................ 0x0080: 0000 0000 0000 4800 0000 0200 0000 0000 ......H......... 0x0090: 0000 8800 0000 0000 0000 0000 0000 0000 ................ 0x00a0: 0000 0100 0000 0000 0000 0000 0000 0000 ................ 0x00b0: 0000 0000 0000 c2ca 0031 0000 0000 0000 .........1...... 0x00c0: 0000 0000 0000 0000 0000 5508 0000 6510 ..........U...e. 0x00d0: 0000 ee53 4c00 0000 0000 0000 0000 0000 ...SL........... 0x00e0: 0000 0000 0000 0000 0000 0000 0000 6264 ..............bd 0x00f0: 7863 0000 0000 0000 0000 0000 0000 0000 xc.............. 0x0100: 0000 0000 0000 0000 0000 0000 0000 0000 ................ 0x0110: 0000 0100 0000 0000 0000 0000 0000 30ff ..............0. 0x0120: 0002 0000 0000 0000 0000 0000 0000 0000 ................ 0x0130: 0000 0000 0000 0000 0000 0000 0000 0000 ................ 0x0140: 0000 0000 0000 0000 0000 0c04 0000 0000 ................ 0x0150: 0000 0000 0000 0000 0000 0000 0000 0000 ................ 0x0160: 0000 .. 01:49:21.802982 IP (tos 0x6,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto UDP (17), length 380) 172.0.0.1.8197 > 172.0.16.1.8197: [udp sum ok] UDP, length 352 0x0000: 4e41 5000 1001 4e41 5000 0001 0800 4506 NAP...NAP.....E. 0x0010: 017c 0000 4000 4011 d168 ac00 0001 ac00 .|..@.@..h...... 0x0020: 1001 2005 2005 0168 672f abcd abcd 0000 .......hg/...... 0x0030: 0000 3c80 f502 0000 0000 0000 0000 0000 ..<............. 0x0040: 0000 0000 0000 7856 3412 0411 0008 0000 ......xV4....... 0x0050: 0000 5508 0000 0100 0000 3d25 2600 0000 ..U.......=%&... 0x0060: 0000 d007 0100 0000 0000 ffff 0000 0000
[snip]
注意:由于是VM方案,发送到VM的流量可以使用外部报头中的VM接口地址进行封装,以便此流量可以到达VM接口。
注意:采用的捕获是为了演示该方法,并且没有Internet控制消息协议(ICMP)流量。
正在检查FIA组件在线卡。
Check initial counter value.
RP/0/RP0/CPU0:NCS6k-Deploy#sh controllers fia statistics instance 1 loc 0/0/cpu0 FIA Statistics Rack: 0, Slot: 0, Asic instance: 1 FIA Rx (To Fabric) Statistics. ------------------------------------------------------------------------ Input Pkt counters Pkts Bytes Rx pkts from pse : 250 53000 Rx pkts from switch : 993528 349564509 bcast pkts from switch : 0 mcast pkts from switch : 993278 ucast pkts from switch : 250 Rx pkts enqueued(IQM) : 500 86500 Rx pkts dequeued(IQM) : 500 86500 Rx pkts sent to fabric : 500 Cell counters: Data cells sent to fabric : 500 86500 Control cells sent to fabric : 183039783411 Drop counters: Rx burst error drops(NBI) : 0 Rx error drops(Switch) : 0 Rx error drops(pse) : 0 Rx pkt discard drops(IQM) : 993277 334570329 Pkt crc error drops(FDT) : 0 Unreachable dest cell drops : 0 Internal Error Count : 41984110 Internal Drop Count : 0 FIA Tx (From Fabric) Statistics -------------------------------------------------- ---------------------- Cell counters: Pkts Bytes Data cells : 500 Control cells : 179368087015 Reassembled packet counters: Pkts received from fabric : 500 Tx Ucast pkts : 500 86500 Tx Mcast pkts : 0 0 Tx pkts (EPNI) : 500 81000 Tx pkts sent to switch : 250 53000 Bcast pkts sent to switch : 0 Mcast pkts sent to switch : 0 Ucast pkts sent to switch : 250 Tx segments sent to pse : 250 29000 Tx pkts sent to pse (NBI) : 500 49000 Drop counters: Tx pkts dropped EPNI : 0 Tx Ucast pkts dropped : 0 Tx Mcast pkts dropped : 0 Tx pkts dropped in EGQ(RQP + EHP): 0 Control cell Drops : 0 Data cell Drops : 0 Tx pkts dropped switch : 0 Tx pkts dropped pse : 0 Internal Error Count : 0 Internal Drop Count : 0
Initiate ping of 1000 packets.
RP/0/RP0/CPU0:NCS6k-Deploy#ping 10.67.1.1 count 1000 Type escape sequence to abort. Sending 1000, 100-byte ICMP Echos to 10.67.1.1, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! Success rate is 100 percent (1000/1000), round-trip min/avg/max = 2/3/8 ms
Check counters again to see increment of 1000 packets.
RP/0/RP0/CPU0:NCS6k-Deploy#sh controllers fia statistics instance 1 loc 0/0/cpu0 FIA Statistics Rack: 0, Slot: 0, Asic instance: 1 FIA Rx (To Fabric) Statistics. ------------------------------------------------------------------------ Input Pkt counters Pkts Bytes Rx pkts from pse : 1250 265000 Rx pkts from switch : 994927 349849612 bcast pkts from switch : 0 mcast pkts from switch : 993677 ucast pkts from switch : 1250 Rx pkts enqueued(IQM) : 2500 432500 Rx pkts dequeued(IQM) : 2500 432500 Rx pkts sent to fabric : 2500 Cell counters: Data cells sent to fabric : 2500 432500 Control cells sent to fabric : 183111332632 Drop counters: Rx burst error drops(NBI) : 0 Rx error drops(Switch) : 0 Rx error drops(pse) : 0 Rx pkt discard drops(IQM) : 993676 334707420 Pkt crc error drops(FDT) : 0 Unreachable dest cell drops : 0 Internal Error Count : 42004879 Internal Drop Count : 0 FIA Tx (From Fabric) Statistics -------------------------------------------------- ---------------------- Cell counters: Pkts Bytes Data cells : 2500 Control cells : 179438200981 Reassembled packet counters: Pkts received from fabric : 2500 Tx Ucast pkts : 2500 432500 Tx Mcast pkts : 0 0 Tx pkts (EPNI) : 2500 405000 Tx pkts sent to switch : 1250 265000 Bcast pkts sent to switch : 0 Mcast pkts sent to switch : 0 Ucast pkts sent to switch : 1250 Tx segments sent to pse : 1250 145000 Tx pkts sent to pse (NBI) : 2500 245000 Drop counters: Tx pkts dropped EPNI : 0 Tx Ucast pkts dropped : 0 Tx Mcast pkts dropped : 0 Tx pkts dropped in EGQ(RQP + EHP): 0 Control cell Drops : 0 Data cell Drops : 0 Tx pkts dropped switch : 0 Tx pkts dropped pse : 0 Internal Error Count : 0 Internal Drop Count : 0
检查分组交换引擎(PSE)计数器。
Check initial counter value.
RP/0/RP0/CPU0:NCS6k-Deploy#sh control pse statistics summ instance 1 loc 0/0/cpu0 STATISTICS SUMMARY: INGRESS ------- From L2 [LSIM]: Packets: 1261 Bytes: 163336 To Fabric: Packets: 1250 Bytes: 265000 EGRESS ------ From Fabric: Packets: 1250 Bytes: 145000 To TM: Packets: 1272 To L2 [LSIM]: Packets: 1261 Bytes: 142962 TO/FROM CPU ----------- To CPU: Packets: 11 From CPU: Packets: 11
Generate 1000 ping packets.
RP/0/RP0/CPU0:NCS6k-Deploy#ping 10.67.1.1 count 1000 Type escape sequence to abort. Sending 1000, 100-byte ICMP Echos to 10.67.1.1, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! Success rate is 100 percent (1000/1000), round-trip min/avg/max = 3/4/9 ms
Check counter again to see increment of 1000 packets.
RP/0/RP0/CPU0:NCS6k-Deploy#sh control pse statistics summ instance 1 loc 0/0/cpu0 STATISTICS SUMMARY: INGRESS ------- From L2 [LSIM]: Packets: 2261 Bytes: 293336 To Fabric: Packets: 2250 Bytes: 477000 EGRESS ------ From Fabric: Packets: 2250 Bytes: 261000 To TM: Packets: 2272 To L2 [LSIM]: Packets: 2261 Bytes: 256962 TO/FROM CPU ----------- To CPU: Packets: 11 From CPU: Packets: 11
正在检查物理层接口模块(PLIM)ASIC计数器。
Check initial counter value.
RP/0/RP0/CPU0:NCS6k-Deploy#sh controllers plim asic statistics interface Te0/0/0/2/0 Node: 0/0/CPU0 ------------------------------------------------------------------------------- TenGigE0/0/0/2/0 Tx Statistics ---------------------------------------------- Total Packets : 2256 Total Bytes : 265884 Total Good Packets : 2256 Total Good Bytes : 265884 Unicast Packets : 2256 Multicast Packets : 0 Broadcast Packets : 0 64 Byte Packets : 6 65to127 Byte Packets : 2250 128to255 Byte Packets : 0 256to511 Byte Packets : 0 512to1023 Byte Packets : 0 1024to1518 Byte Packets : 0 1519to1522 Byte Packets : 0 1523to1548 Byte Packets : 0 1549to2000 Byte Packets : 0 2001to_MRU Byte Packets : 0 Non Pause BPDU Packets : 0 Classic Pause Packets : 0 Class Based Pause Pkts 0 : 0 Class Based Pause Pkts 1 : 0 Class Based Pause Pkts 2 : 0 Class Based Pause Pkts 3 : 0 Class Based Pause Pkts 4 : 0 Class Based Pause Pkts 5 : 0 Class Based Pause Pkts 6 : 0 Class Based Pause Pkts 7 : 0 Dropped Packets =============== Drained Packets : 0 Abort : 0 Length Error : 0 Giant : 0 Tail Drop: HP Queue : 0 Tail Drop: LP Queue : 0 TenGigE0/0/0/2/0 Rx Statistics ---------------------------------------------- Total Packets : 2256 Total Bytes : 265884 Total Good Packets : 2256 Total Good Bytes : 265884 Unicast Packets : 2256 Multicast Packets : 0 Broadcast Packets : 0 64 Byte Packets : 6 65to127 Byte Packets : 2250 128to255 Byte Packets : 0 256to511 Byte Packets : 0 512to1023 Byte Packets : 0 1024to1518 Byte Packets : 0 1519to1522 Byte Packets : 0 1523to1548 Byte Packets : 0 1549to2000 Byte Packets : 0 2001to_MRU Byte Packets : 0 Non Pause BPDU Packets : 0 Classic Pause Packets : 0 Class Based Pause Pkts 0 : 0 Class Based Pause Pkts 1 : 0 Class Based Pause Pkts 2 : 0 Class Based Pause Pkts 3 : 0 Class Based Pause Pkts 4 : 0 Class Based Pause Pkts 5 : 0 Class Based Pause Pkts 6 : 0 Class Based Pause Pkts 7 : 0 Dropped Packets =============== Runts : 0 Fragments : 0 Jumbo : 0 Jabber : 0 CRC : 0 Code Error : 0 Code Violation : 0 Bad Preamble : 0 IPG Violation : 0 Packet HPQ QoS Ctl Drop : 0 Bytes HPQ QoS Ctl Drop : 0 Packet HPQ QoS HP Drop : 0 Bytes HPQ QoS HP Drop : 0 Packet HPQ Ctl Tail Drop : 0 Bytes HPQ Ctl Tail Drop : 0 Packet HPQ HP Tail Drop : 0 Bytes HPQ HP Tail Drop : 0 Packet LPQ LP1 Tail Drop : 0 Bytes LPQ LP1 Tail Drop : 0 Packet LPQ LP2 Tail Drop : 0 Bytes LPQ LP2 Tail Drop : 0 Packet TCAM Miss : 0 Bytes TCAM Miss : 0 Packet EOP Abort Drop : 0 Bytes EOP Abort Drop : 0 Packet Policy Deny : 0 Bytes Policy Deny : 0 Rx Packet Drop Details ====================== Unknown Dest MAC Pkts : 0 Unknown E-Type Pkts : 0 Unknown Encap Pkts : 0 Unknown Encap Bytes : 0 Unknown VLAN Pkts : 0 Unknown VLAN Bytes : 0 L2 Subif VLAN Deny Pkts : 0 L2 Subif VLAN Deny Bytes : 0 Rx Accepted Packet Details ============================ Packet HPQ CTL Sent : 6 Bytes HPQ CTL Sent : 384 Packet HPQ HP Sent : 0 Bytes HPQ HP Sent : 0 Packet LPQ LP1 Sent : 0 Bytes LPQ LP1 Sent : 0 Packet LPQ LP2 Sent : 0 Bytes LPQ LP2 Sent : 0
Initiate 1000 ping packets.
RP/0/RP0/CPU0:NCS6k-Deploy#ping 10.67.1.1 count 1000 Type escape sequence to abort. Sending 1000, 100-byte ICMP Echos to 10.67.1.1, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! Success rate is 100 percent (1000/1000), round-trip min/avg/max = 3/5/9 ms
Check counter again to see increment of 1000 packets.
RP/0/RP0/CPU0:NCS6k-Deploy#sh controllers plim asic statistics interface Ten0/0/0/2/0 Node: 0/0/CPU0 ------------------------------------------------------------------------------- TenGigE0/0/0/2/0 Tx Statistics ---------------------------------------------- Total Packets : 3256 Total Bytes : 383884 Total Good Packets : 3256 Total Good Bytes : 383884 Unicast Packets : 3256 Multicast Packets : 0 Broadcast Packets : 0 64 Byte Packets : 6 65to127 Byte Packets : 3250 128to255 Byte Packets : 0 256to511 Byte Packets : 0 512to1023 Byte Packets : 0 1024to1518 Byte Packets : 0 1519to1522 Byte Packets : 0 1523to1548 Byte Packets : 0 1549to2000 Byte Packets : 0 2001to_MRU Byte Packets : 0 Non Pause BPDU Packets : 0 Classic Pause Packets : 0 Class Based Pause Pkts 0 : 0 Class Based Pause Pkts 1 : 0 Class Based Pause Pkts 2 : 0 Class Based Pause Pkts 3 : 0 Class Based Pause Pkts 4 : 0 Class Based Pause Pkts 5 : 0 Class Based Pause Pkts 6 : 0 Class Based Pause Pkts 7 : 0 Dropped Packets =============== Drained Packets : 0 Abort : 0 Length Error : 0 Giant : 0 Tail Drop: HP Queue : 0 Tail Drop: LP Queue : 0 TenGigE0/0/0/2/0 Rx Statistics ---------------------------------------------- Total Packets : 3256 Total Bytes : 383884 Total Good Packets : 3256 Total Good Bytes : 383884 Unicast Packets : 3256 Multicast Packets : 0 Broadcast Packets : 0 64 Byte Packets : 6 65to127 Byte Packets : 3250 128to255 Byte Packets : 0 256to511 Byte Packets : 0 512to1023 Byte Packets : 0 1024to1518 Byte Packets : 0 1519to1522 Byte Packets : 0 1523to1548 Byte Packets : 0 1549to2000 Byte Packets : 0 2001to_MRU Byte Packets : 0 Non Pause BPDU Packets : 0 Classic Pause Packets : 0 Class Based Pause Pkts 0 : 0 Class Based Pause Pkts 1 : 0 Class Based Pause Pkts 2 : 0 Class Based Pause Pkts 3 : 0 Class Based Pause Pkts 4 : 0 Class Based Pause Pkts 5 : 0 Class Based Pause Pkts 6 : 0 Class Based Pause Pkts 7 : 0 Dropped Packets =============== Runts : 0 Fragments : 0 Jumbo : 0 Jabber : 0 CRC : 0 Code Error : 0 Code Violation : 0 Bad Preamble : 0 IPG Violation : 0 Packet HPQ QoS Ctl Drop : 0 Bytes HPQ QoS Ctl Drop : 0 Packet HPQ QoS HP Drop : 0 Bytes HPQ QoS HP Drop : 0 Packet HPQ Ctl Tail Drop : 0 Bytes HPQ Ctl Tail Drop : 0 Packet HPQ HP Tail Drop : 0 Bytes HPQ HP Tail Drop : 0 Packet LPQ LP1 Tail Drop : 0 Bytes LPQ LP1 Tail Drop : 0 Packet LPQ LP2 Tail Drop : 0 Bytes LPQ LP2 Tail Drop : 0 Packet TCAM Miss : 0 Bytes TCAM Miss : 0 Packet EOP Abort Drop : 0 Bytes EOP Abort Drop : 0 Packet Policy Deny : 0 Bytes Policy Deny : 0 Rx Packet Drop Details ====================== Unknown Dest MAC Pkts : 0 Unknown E-Type Pkts : 0 Unknown Encap Pkts : 0 Unknown Encap Bytes : 0 Unknown VLAN Pkts : 0 Unknown VLAN Bytes : 0 L2 Subif VLAN Deny Pkts : 0 L2 Subif VLAN Deny Bytes : 0 Rx Accepted Packet Details ============================ Packet HPQ CTL Sent : 6 Bytes HPQ CTL Sent : 384 Packet HPQ HP Sent : 0 Bytes HPQ HP Sent : 0 Packet LPQ LP1 Sent : 0 Bytes LPQ LP1 Sent : 0 Packet LPQ LP2 Sent : 0 Bytes LPQ LP2 Sent : 0
选中“show interface”计数器。
最好在第一步中检查此项,但在数据包流的顺序中,此项将是最后一项。它有助于确定数据包是否已发送到线路,以及数据包是否已从线路返回。它有助于缩小问题范围,无论问题是在机箱内还是在机箱外。
Check initial counter values.
RP/0/RP0/CPU0:NCS6k-Deploy#show inter ten 0/0/0/2/0 TenGigE0/0/0/2/0 is up, line protocol is up Interface state transitions: 1 Hardware is TenGigE, address is e051.2a0f.8c29 (bia e051.2a0f.8c29) Description: Connected to 0/7/0/1 - CRS-F Internet address is 10.67.1.2/30 MTU 1514 bytes, BW 10000000 Kbit (Max: 10000000 Kbit) reliability 0/255, txload 0/255, rxload 0/255 Encapsulation ARPA, Full-duplex, 10000Mb/s, SR, link type is force-up output flow control is off, input flow control is off loopback not set, ARP type ARPA, ARP timeout 04:00:00 Last input 00:14:22, output 00:14:22 Last clearing of "show interface" counters 22:08:42 30 second input rate 0 bits/sec, 0 packets/sec 30 second output rate 0 bits/sec, 0 packets/sec 3256 packets input, 370860 bytes, 0 total input drops 0 drops for unrecognized upper-level protocol Received 0 broadcast packets, 0 multicast packets 0 runts, 0 giants, 0 throttles, 0 parity 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 3256 packets output, 370860 bytes, 0 total output drops Output 0 broadcast packets, 0 multicast packets 0 output errors, 0 underruns, 0 applique, 0 resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions
Initiate 1000 ping packets. RP/0/RP0/CPU0:NCS6k-Deploy#ping 10.67.1.1 cou 1000 Type escape sequence to abort. Sending 1000, 100-byte ICMP Echos to 10.67.1.1, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! Success rate is 100 percent (1000/1000), round-trip min/avg/max = 3/4/8 ms
Check counter again to see increment of 1000 packets.
RP/0/RP0/CPU0:NCS6k-Deploy#show inter ten 0/0/0/2/0 TenGigE0/0/0/2/0 is up, line protocol is up Interface state transitions: 1 Hardware is TenGigE, address is e051.2a0f.8c29 (bia e051.2a0f.8c29) Description: Connected to 0/7/0/1 - CRS-F Internet address is 10.67.1.2/30 MTU 1514 bytes, BW 10000000 Kbit (Max: 10000000 Kbit) reliability 255/255, txload 0/255, rxload 0/255 Encapsulation ARPA, Full-duplex, 10000Mb/s, SR, link type is force-up output flow control is off, input flow control is off loopback not set, ARP type ARPA, ARP timeout 04:00:00 Last input 00:00:00, output 00:00:00 Last clearing of "show interface" counters 22:09:38 30 second input rate 1000 bits/sec, 2 packets/sec 30 second output rate 1000 bits/sec, 2 packets/sec 4256 packets input, 484860 bytes, 0 total input drops 0 drops for unrecognized upper-level protocol Received 0 broadcast packets, 0 multicast packets 0 runts, 0 giants, 0 throttles, 0 parity 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 4256 packets output, 484860 bytes, 0 total output drops Output 0 broadcast packets, 0 multicast packets 0 output errors, 0 underruns, 0 applique, 0 resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions