对MD精心制作的配置的MD与FCIP
简介
本文档提供了详细的TCP/IP光纤通道(FCIP)多层导向器交换机(MDS)到MDS的配置示例。
FCIP描述了在基于IP的光纤信道(FC)存储区域网络（SAN）岛实现互连的机制，以便在单个FC光组织中组成统一的SAN。FCIP依靠基于IP的网络服务，在通过局域网、城域网或广域网的SAN岛之间提供连连通性。
图1 — 通过FCIP连接的光纤通道SAN 
FCIP 在端口 3225 上使用传输控制协议 (TCP) 作为一种网络层传输技术。
先决条件
要求
尝试进行此配置之前，请确保满足以下要求：
-
IP主干必须运行并提供所需的带宽，以支持在FCIP链路上运行的应用 — 这可以是第2层(L2)或第3层(L3)拓扑。
-
如果是L3拓扑，则必须设置并配置中间路由器或多层交换机，以在FCIP隧道的源IP地址和目的IP地址之间适当转发IP流量。如果在FCIP对等体之间路径中的任何网络设备上实施服务质量(QoS)或流量整形，则在配置多层导向器交换机(MDS)FCIP配置文件上的任何TCP相关参数和功能之前，应咨询管理IP基础设施的网络管理器以获取必要的详细信息。
-
如果在MDS IP存储(IPS)服务模块上配置子接口，则与MDS相邻的以太网交换机必须支持并配置802.1Q中继。
使用的组件
本文档中的信息基于以下软件和硬件版本：
-
带IPS服务模块(DS-X9308-SMIP)的MDS 9509，运行版本1.2.(2a)
-
带IPS服务模块(DS-X9308-SMIP)的MDS 9216，运行版本1.2.(2a)
-
运行Catalyst OS(CatOS)7.4(3)的Catalyst 6509
-
带有Emulex LP9K HBA的Win2003服务器(HPQ Pro-Liant-P4)
-
IBM 存储阵列 (ESS-2105-F20)
本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始（默认）配置。如果您使用的是真实网络，请确保您已经了解所有命令的潜在影响。
规则
有关文档规则的详细信息，请参阅 Cisco 技术提示规则。
背景信息
FCIP包括以下规格：
ANSI T11
-
FC-SW-2描述FC交换机的操作和交互作用包括E_Port和结构操作。
-
FC-BB-2是适合通过TCP网络主干的FC交换网络扩展的映射，它同时还定义了支持E_端口 和B_端口的参考模型。
IETF IPS 工作组
-
TCP的FC包括在一个IP网络上传输FC帧的TCP/IP要求。
-
FC 帧封装可定义普通的光纤封装格式。
两个SAN交换机或交换矩阵之间通过FCIP的互连称为FCIP链路，可以包含一个或多个TCP连接。FCIP链路的每个结尾与虚拟E端口(VE_端口)或B_端口连接，这取决于实施情况。FC-BB 和 FC-BB-2 可描述两种方法之间的区别。IPS服务模块(DS-X9308-SMIP)支持两种模式，但默认为VE_Port，如果所有相关对等体都是DS-X9308-SMIP模块，则也建议运行VE_Port模式。在此示例拓扑中，讨论了PortChannel上的FCIP、要配置的TCP参数和FSF（特殊帧）配置参数。
配置
本部分提供有关如何配置本文档所述功能的信息。
在MDS上，您需要熟悉两个平台的IPS配置指南。在Cisco.com上的配置IP存储中，您可以找到最新版本的手册。
注意：使用命令查找工具(仅限注册客户)可查找有关本文档中使用的命令的详细信息。
网络图
本文档使用以下网络设置：
图2 — 拓扑3 
拓扑3描绘了由两个单独的FCIP隧道形成的一个FCIP端口通道；对等接口跨IP云。IP云折叠为一台多层交换机(Catalyst 6500)，该交换机将流量从子网A路由到子网C，从子网C路由到子网A（从子网B路由到子网D，从子网D路由到子网A）。 子网定义如下：
-
子网 A:100.100.100.0/30 - Bison int Gig4/1
-
子网 B:100.100.100.4/30 - Bison int Gig4/2
-
子网 C:200.200.200.0/30-坎特伯雷Gig2/1
-
子网 D:200.200.200.4/30 — 坎特伯雷Gig2/2
该拓扑提供已知最大带宽100 Mbps和最小带宽100 Mbps，这是通过此IP云为相关IP流量运行的配置文件。初始配置显示了基于FCIP的端口通道和TCP流量调节的方面。在后续部分中，将进一步说明FSF、被动TCP接口和FCIP时间戳。
配置
本文档使用以下配置：
| 具备 IPS-8 模块的 MDS9509 (Bison) |
|---|
bison# sh ver Cisco Storage Area Networking Operating System (SAN-OS) Software TAC support: http://www.cisco.com/tac Copyright (c) 2002-2003 by Cisco Systems, Inc. All rights reserved. The copyright for certain works contained herein are owned by Andiamo Systems, Inc. and/or other third parties and are used and distributed under license. Software BIOS: version 1.0.8 loader: version 1.2(2) kickstart: version 1.2(2a) system: version 1.2(2a) BIOS compile time: 08/07/03 kickstart image file is: bootflash:/k122a kickstart compile time: 9/23/2003 11:00:00 system image file is: bootflash:/s122a system compile time: 10/8/2003 18:00:00 Hardware RAM 1024584 kB bootflash: 500736 blocks (block size 512b) slot0: 0 blocks (block size 512b) bison uptime is 1 days 15 hours 45 minute(s) 44 second(s) Last reset Reason: Unknown System version: 1.2(2a) Service: bison# sh run Building Configuration ... fcip profile 1 ip address 100.100.100.1 tcp max-bandwidth-mbps 100 min-available-bandwidth-mbps 100 round-trip-time-ms 10 !--- TCP bandwidth parameters defined specifically for this FCIP tunnel. !--- Restricted to 100 Mbps max and min. See the Note on TCP Parameters !--- comment section in this table below for more details. fcip profile 2 ip address 100.100.100.5 tcp max-bandwidth-mbps 100 min-available-bandwidth-mbps 100 round-trip-time-ms 10 !--- TCP max and min bandwidth parameter are configured here exactly the !--- same as for FCIP 1 because both tunnels are combined in one PortChannel !--- interface and are subject to the same bandwidth restrictions in the IP core. vsan database vsan 600 vsan 601 fcdomain domain 1 preferred vsan 600 fcdomain domain 1 preferred vsan 601 interface port-channel 1 switchport trunk allowed vsan 600-601 interface fcip1 channel-group 1 force no shutdown use-profile 1 peer-info ipaddr 200.200.200.1 !--- Interface FCIP 1 is a member of channel-group 1. The force keyword makes it !--- adopt the specific settings configured on interface port-channel 1. interface fcip2 channel-group 1 force no shutdown use-profile 2 peer-info ipaddr 200.200.200.5 !--- Interface FCIP 2 is also member of channel-group 1. boot system bootflash:/s122a sup-1 boot kickstart bootflash:/k122a sup-1 boot system bootflash:/s122a sup-2 boot kickstart bootflash:/k122a sup-2 ip domain-name cisco.com ip name-server 144.254.10.123 ip route 200.200.200.0 255.255.255.252 100.100.100.2 distance 2 ip route 200.200.200.4 255.255.255.252 100.100.100.6 distance 2 !--- FCIP interfaces are on separate IP subnets, so in order to reach the FCIP !--- peer IP address, you need adequate static routes to an L3 device that !--- knows how to forward the packets to the final destination. Multiple routes !--- to the same destination IP subnet are allowed, and the distance parameter !--- can be used to specify a preferred next hop. Multiple next hops would !--- require a subnet mask providing for a larger number of host; for example, !--- a 28-bit subnet mask. ssh key dsa 768 force ssh server enable switchname bison zone default-zone permit vsan 600-601 interface GigabitEthernet4/1 ip address 100.100.100.1 255.255.255.252 switchport mtu 3000 no shutdown !--- MTU size is defined as 3000 bytes. Make sure that all intermediate network !--- devices between this interface and the peer IP address are capable of !--- switching and routing Jumbo frames. In order to avoid FC Frame split, !--- an MTU value of 2300 is required; 3000 is used in the configuration example !--- for simplicity. FCIP TCP segments will normally never exceed 2264 bytes for !--- TE ports or 2256 bytes for E ports, regardless of the configured MTU size. interface GigabitEthernet4/2 ip address 100.100.100.5 255.255.255.252 switchport mtu 3000 no shutdown interface fc3/1 interface fc3/2 interface fc3/3 interface fc3/4 interface fc3/5 interface fc3/6 interface fc3/7 interface fc3/8 interface fc3/9 interface fc3/10 interface fc3/11 interface fc3/12 interface fc3/13 interface fc3/14 interface fc3/15 interface fc3/16 interface mgmt0 ip address 10.48.69.151 255.255.255.128 !--- Note on TCP Parameters !--- The following TCP parameters can be individually configured per FCIP profile: bison(config-profile)# tcp ? cwm Enable congestion window monitoring keepalive-timeout Set keep alive timeout in sec max-bandwidth-kbps Configure maximum available path bandwidth in Kbps max-bandwidth-mbps Configure maximum available path bandwidth in Mbps max-retransmissions Maximum number of retransmissions min-retransmit-time Set minimum retransmit time in millisecond pmtu-enable Enable PMTU Discovery sack-enable Enable SACK option for TCP send-buffer-size Send buffer size in KBytes !--- The CWM parameter default value is 10K and should be left untouched under !--- normal conditions. Congestion window monitoring (CWM) is a way of !--- controlling burstiness after long idle times or loss of Acks. !--- The keepalive-timeout is the TCP keepalive timeout value and is !--- set to 60 seconds by default, though it can range between 1 and 7200 seconds. !--- The max- and min-bandwidth parameters program the TCP Maximum Window Size !--- (scaling factor) and engages an internal “shaper” functionality. !--- These values should be carefully chosen and requires understanding of the !--- intermediate network’s end-to-end topology. The default values are to be !--- changed according to the aforementioned requirements. !--- The Round-trip-time can be derived once you have your FCIP tunnel up and !--- running by issuing the following command: bison# ips measure 200.200.200.1 interface gigabitethernet 4/1 Round trip time is 53 micro seconds (0.05 milliseconds ) !--- Always add an additional margin of at least a few microseconds to this value. !--- The max-retransmissions counter is set to 4 by default. In a healthy network !--- environment, this value should be left unchanged. !--- The max-retransmission timer is set to 200 milliseconds. If you experience !--- extremely high retransmission counters, this value can be increased; but, !--- in general, changing this parameter is not required unless the RTT is !--- above 200 milliseconds. !--- The PMTU (Path MTU discovery) is enabled by default. Best practice is to know !--- what is the maximum MTU size supported by all interfaces along the logical !--- path between both peers. !--- The SACK feature (Selective Acknowledgment) is not enabled by default. !--- Consider enabling it when you have a lot of retransmissions occurring between !--- the two peers. SACK allows selective retransmissions of your window, which is !--- beneficial if larger maximum window sizes are configured and retransmissions !--- occur frequently. It is enabled in this sample configuration; when you do so, !--- make sure that it is enabled at both sides of the link. !--- The send-buffer-size is the amount of buffers in addition to the TCP window !--- that are allowed to be transmitted out before starting to flow control the FC !--- sources. The default value is set to 0. |
-
有关PMTU的详细信息，请参阅RFC 1191 — 路径MTU发现
。 -
有关SACK的详细信息，请参阅RFC 2018 - TCP选择性确认选项
和RFC 2883 - TCP选择性确认(SACK)选项的扩展
。| 具备 IPS-8 模块的 MDS9216 (Canterbury) |
|---|
canterbury# sh run Building Configuration ... fcip profile 200 ip address 200.200.200.1 tcp max-bandwidth-mbps 100 min-available-bandwidth-mbps 100 round-trip-time-ms 10 fcip profile 201 ip address 200.200.200.5 tcp max-bandwidth-mbps 100 min-available-bandwidth-mbps 100 round-trip-time-ms 10 !--- The TCP parameters are identical to what is configured on the peering !--- FCIP interfaces. Only in very specific cases should different values be !--- considered, for example, if the return-path(s) are running across a different !--- part of the network or if the application dictates asymmetrical values. vsan database vsan 600 vsan 601 fcdomain domain 2 preferred vsan 600 fcdomain domain 2 preferred vsan 601 interface port-channel 2 switchport trunk mode auto switchport trunk allowed vsan 600-601 interface fcip1 channel-group 2 force no shutdown use-profile 200 peer-info ipaddr 100.100.100.1 interface fcip2 channel-group 2 force no shutdown use-profile 201 peer-info ipaddr 100.100.100.5 !--- Both FCIP 1 and FCIP 2 are bound to the same channel-group 2. Also note that !--- there is no strict relationship between profile-id and FCIP interface !--- numbering here, as this is not a requirement. From a management and !--- troubleshooting perspective, however, a “strict” relationship of both values !--- is recommended. vsan database vsan 600 interface fc1/1 vsan 601 interface fc1/8 boot system bootflash:/s122a boot kickstart bootflash:/k122a ip domain-name cisco.com ip name-server 144.254.10.123 ip default-gateway 10.48.69.129 ip route 100.100.100.0 255.255.255.252 200.200.200.2 distance 2 ip route 100.100.100.4 255.255.255.252 200.200.200.6 distance 2 !--- IP routes are defined for both FCIP peer IP addresses. The next hop must be !--- aware of the best route to the peer’s addresses or to the relevant IP subnets. ssh key dsa 768 force ssh server enable switchname canterbury system default switchport trunk mode auto username admin password 5 $1$KcCrqxlu$mtU03/60PRUIfjl.aeEEc0 role network-admin zone default-zone permit vsan 600-601 zoneset distribute full vsan 1-4093 interface GigabitEthernet2/1 ip address 200.200.200.1 255.255.255.252 switchport mtu 3000 no shutdown interface GigabitEthernet2/2 ip address 200.200.200.5 255.255.255.252 switchport mtu 3000 no shutdown interface GigabitEthernet2/3 interface GigabitEthernet2/4 interface GigabitEthernet2/5 interface GigabitEthernet2/6 interface GigabitEthernet2/7 interface GigabitEthernet2/8 interface fc1/1 interface fc1/2 interface fc1/3 interface fc1/4 interface fc1/5 interface fc1/6 interface fc1/7 interface fc1/8 interface fc1/9 interface fc1/10 interface fc1/11 interface fc1/12 interface fc1/13 interface fc1/14 interface fc1/15 interface fc1/16 interface mgmt0 ip address 10.48.69.156 255.255.255.128 interface iscsi2/1 interface iscsi2/2 interface iscsi2/3 interface iscsi2/4 interface iscsi2/5 interface iscsi2/6 interface iscsi2/7 interface iscsi2/8 |
验证
使用本部分可确认配置能否正常运行。
命令输出解释程序（仅限注册用户）(OIT) 支持某些 show 命令。使用 OIT 可查看对 show 命令输出的分析。
-
show interface gig x/y - 显示绑定到 FCIP 配置文件的相关千兆接口的状态。
-
show ips stats tcp int gig x/y---显示相关千兆接口的TCP统计数据和活动连接。
-
show ips arp int gig x/y - 显示相关千兆接口的所有地址解析协议 (ARP) 条目；对端的下一跳应该是存在于此列表中。
-
show ips ip route int gig x/y - 显示通过相关千兆接口的特定路由。
-
show interface fcip x——显示FCIP接口状态和与此FCIP隧道相关的全部详情。
-
show profile fcip x ——显示文件夹所捆绑的IP地址，以及所有配置的TCP参数。
-
show int fcip x counters——用于检查是否有任何帧通过FCIP隧道。
-
show fcdomain vsan x - 列出所有与域相关的详细信息；过去常常验证结构在FCIP隧道间被形成。
-
show fcns da vsan x ---显示与VSAN相关的所有pwwn、FC4-类型和FCID;用于验证所有期望的条目通过FCIP隧道被分配。
故障排除
使用本部分可排除配置故障。
请务必多次发出show命令以构建计数器历史记录。与时间点无关且仅收集一次的计数器大多无用。
使用下面所示的配置进行进一步的故障排除。
| MDS9509 (Bison) |
|---|
bison# sh int gig 4/1
GigabitEthernet4/1 is up
Hardware is GigabitEthernet, address is 0005.3000.a85a
Internet address is 100.100.100.1/30
MTU 3000 bytes
Port mode is IPS
Speed is 1 Gbps
Beacon is turned off
Auto-Negotiation is turned on
5 minutes input rate 312 bits/sec, 39 bytes/sec, 0 frames/sec
5 minutes output rate 312 bits/sec, 39 bytes/sec, 0 frames/sec
8685 packets input, 976566 bytes
0 multicast frames, 0 compressed
0 input errors, 0 frame, 0 overrun 0 fifo
8679 packets output, 972382 bytes, 0 underruns
0 output errors, 0 collisions, 0 fifo
0 carrier errors
bison# sh int gig 4/2
GigabitEthernet4/2 is up
Hardware is GigabitEthernet, address is 0005.3000.a85b
Internet address is 100.100.100.5/30
MTU 3000 bytes
Port mode is IPS
Speed is 1 Gbps
Beacon is turned off
Auto-Negotiation is turned on
5 minutes input rate 16 bits/sec, 2 bytes/sec, 0 frames/sec
5 minutes output rate 16 bits/sec, 2 bytes/sec, 0 frames/sec
590 packets input, 46496 bytes
0 multicast frames, 0 compressed
0 input errors, 0 frame, 0 overrun 0 fifo
547 packets output, 30898 bytes, 0 underruns
0 output errors, 0 collisions, 0 fifo
0 carrier errors
bison# sh ips stats tcp int gig 4/1
TCP Statistics for port GigabitEthernet4/1
Connection Stats
14 active openings, 4 accepts
4 failed attempts, 0 reset received, 14 established
Segment stats
8897 received, 8505 sent, 0 retransmitted
0 bad segments received, 0 reset sent
TCP Active Connections
Local Address Remote Address State Send-Q Recv-Q
100.100.100.1:65480 200.200.200.1:3225 ESTABLISH 0 0
100.100.100.1:65482 200.200.200.1:3225 ESTABLISH 0 0
100.100.100.1:3225 0.0.0.0:0 LISTEN 0 0
bison# sh ips stats tcp int gig 4/2
TCP Statistics for port GigabitEthernet4/2
Connection Stats
2 active openings, 0 accepts
0 failed attempts, 0 reset received, 2 established
Segment stats
598 received, 43 sent, 0 retransmitted
0 bad segments received, 0 reset sent
TCP Active Connections
Local Address Remote Address State Send-Q Recv-Q
100.100.100.5:65531 200.200.200.5:3225 ESTABLISH 0 0
100.100.100.5:65533 200.200.200.5:3225 ESTABLISH 0 0
100.100.100.5:3225 0.0.0.0:0 LISTEN 0 0
bison# sh int fcip1-2
fcip1 is trunking
Hardware is GigabitEthernet
Port WWN is 20:c2:00:05:30:00:7a:de
Peer port WWN is 20:42:00:0c:30:6c:24:40
Admin port mode is auto, trunk mode is on
Port mode is TE
vsan is 1
Belongs to port-channel 1
Trunk vsans (allowed active) (600-601)
Trunk vsans (operational) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
Using Profile id 1 (interface GigabitEthernet4/1)
Peer Information
Peer Internet address is 200.200.200.1 and port is 3225
Special Frame is disabled
Maximum number of TCP connections is 2
Time Stamp is disabled
QOS control code point is 0
QOS data code point is 0
B-port mode disabled
TCP Connection Information
2 Active TCP connections
Control connection: Local 100.100.100.1:65480, Remote 200.200.200.1:3225
Data connection: Local 100.100.100.1:65482, Remote 200.200.200.1:3225
28 Attempts for active connections, 7 close of connections
TCP Parameters
Path MTU 3000 bytes
Current retransmission timeout is 200 ms
Round trip time: Smoothed 5 ms, Variance: 6
Advertized window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Congestion window: Current: 10 KB, Slow start threshold: 118 KB
5 minutes input rate 120 bits/sec, 15 bytes/sec, 0 frames/sec
5 minutes output rate 120 bits/sec, 15 bytes/sec, 0 frames/sec
4077 frames input, 379836 bytes
4071 Class F frames input, 379100 bytes
6 Class 2/3 frames input, 736 bytes
0 Error frames timestamp error 0
4077 frames output, 381064 bytes
4071 Class F frames output, 380364 bytes
6 Class 2/3 frames output, 700 bytes
0 Error frames 0 reass frames
fcip2 is trunking
Hardware is GigabitEthernet
Port WWN is 20:c6:00:05:30:00:7a:de
Peer port WWN is 20:46:00:0c:30:6c:24:40
Admin port mode is auto, trunk mode is on
Port mode is TE
vsan is 1
Belongs to port-channel 1
Trunk vsans (allowed active) (600-601)
Trunk vsans (operational) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
Using Profile id 2 (interface GigabitEthernet4/2)
Peer Information
Peer Internet address is 200.200.200.5 and port is 3225
Special Frame is disabled
Maximum number of TCP connections is 2
Time Stamp is disabled
QOS control code point is 0
QOS data code point is 0
B-port mode disabled
TCP Connection Information
2 Active TCP connections
Control connection: Local 100.100.100.5:65531, Remote 200.200.200.5:3225
Data connection: Local 100.100.100.5:65533, Remote 200.200.200.5:3225
2 Attempts for active connections, 0 close of connections
TCP Parameters
Path MTU 3000 bytes
Current retransmission timeout is 200 ms
Round trip time: Smoothed 0 ms, Variance: 0
Advertized window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Congestion window: Current: 8 KB, Slow start threshold: 118 KB
5 minutes input rate 32 bits/sec, 4 bytes/sec, 0 frames/sec
5 minutes output rate 32 bits/sec, 4 bytes/sec, 0 frames/sec
8 frames input, 1232 bytes
8 Class F frames input, 1232 bytes
0 Class 2/3 frames input, 0 bytes
0 Error frames timestamp error 0
8 frames output, 1228 bytes
8 Class F frames output, 1228 bytes
0 Class 2/3 frames output, 0 bytes
0 Error frames 0 reass frames
bison# sh fcip pro 1
FCIP Profile 1
Internet Address is 100.100.100.1 (interface GigabitEthernet4/1)
Listen Port is 3225
TCP parameters
SACK is enabled
PMTU discovery is enabled, reset timeout is 3600 sec
Keep alive is 60 sec
Minimum retransmission timeout is 200 ms
Maximum number of re-transmissions is 4
Send buffer size is 0 KB
Maximum allowed bandwidth is 100000 kbps
Minimum available bandwidth is 100000 kbps
Estimated round trip time is 10000 usec
Congestion window monitoring is enabled, burst size is 10 KB
bison# sh fcip pro 2
FCIP Profile 2
Internet Address is 100.100.100.5 (interface GigabitEthernet4/2)
Listen Port is 3225
TCP parameters
SACK is enabled
PMTU discovery is enabled, reset timeout is 3600 sec
Keep alive is 60 sec
Minimum retransmission timeout is 200 ms
Maximum number of re-transmissions is 4
Send buffer size is 0 KB
Maximum allowed bandwidth is 100000 kbps
Minimum available bandwidth is 100000 kbps
Estimated round trip time is 10000 usec
Congestion window monitoring is enabled, burst size is 10 KB
bison# sh int port-channel 1
port-channel 1 is trunking
Hardware is Fibre Channel
Port WWN is 24:01:00:05:30:00:7a:de
Admin port mode is auto, trunk mode is on
Port mode is TE
Port vsan is 1
Speed is 2 Gbps
Trunk vsans (admin allowed and active) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
5 minutes input rate 120 bits/sec, 15 bytes/sec, 0 frames/sec
5 minutes output rate 120 bits/sec, 15 bytes/sec, 0 frames/sec
3969 frames input, 369812 bytes
3963 Class F frames input, 369076 bytes
6 Class 2/3 frames input, 736 bytes
0 Error frames timestamp error 0
3969 frames output, 371040 bytes
3963 Class F frames output, 370340 bytes
6 Class 2/3 frames output, 700 bytes
0 Error frames 0 reass frames
Member[1] : fcip1
Member[2] : fcip2
bison# sh ips ip route interface gigabitethernet 4/1
Codes: C - connected, S - static
No default gateway
S 200.200.200.0/30 via 100.100.100.2, GigabitEthernet4/1
C 100.100.100.0/30 is directly connected, GigabitEthernet4/1
bison# sh ips ip route interface gigabitethernet 4/2
Codes: C - connected, S - static
No default gateway
S 200.200.200.4/30 via 100.100.100.6, GigabitEthernet4/2
C 100.100.100.4/30 is directly connected, GigabitEthernet4/2
bison# sh ips arp int gig 4/1
Protocol Address Age (min) Hardware Addr Type Interface
Internet 100.100.100.2 8 0008.e21e.c7bc ARPA GigabitEthernet4/1
!--- Verify that the hardware address listed belongs to the !--- next hop networking device.
bison# sh ips arp int gig 4/2
Protocol Address Age (min) Hardware Addr Type Interface
Internet 100.100.100.6 5 0008.e21e.c7bc ARPA GigabitEthernet4/2
bison# sh int port-channel 1 trunk vsan 600-601
port-channel 1 is trunking
Vsan 600 is up, FCID is 0x010000
Vsan 601 is up, FCID is 0x010000
bison# sh fcdomain vsan 600
The local switch is the Principal Switch.
Local switch run time information:
State: Stable
Local switch WWN: 22:58:00:05:30:00:7a:df
Running fabric name: 22:58:00:05:30:00:7a:df
Running priority: 2
Current domain ID: 0x01(1)
Local switch configuration information:
State: Enabled
FCID persistence: Disabled
Auto-reconfiguration: Disabled
Contiguous-allocation: Disabled
Configured fabric name: 20:01:00:05:30:00:28:df
Configured priority: 128
Configured domain ID: 0x01(1) (preferred)
Principal switch run time information:
Running priority: 2
Interface Role RCF-reject
---------------- ------------- ------------
port-channel 1 Downstream Disabled
---------------- ------------- ------------
bison# sh fcdomain vsan 601
The local switch is the Principal Switch.
Local switch run time information:
State: Stable
Local switch WWN: 22:59:00:05:30:00:7a:df
Running fabric name: 22:59:00:05:30:00:7a:df
Running priority: 2
Current domain ID: 0x01(1)
Local switch configuration information:
State: Enabled
FCID persistence: Disabled
Auto-reconfiguration: Disabled
Contiguous-allocation: Disabled
Configured fabric name: 20:01:00:05:30:00:28:df
Configured priority: 128
Configured domain ID: 0x01(1) (preferred)
Principal switch run time information:
Running priority: 2
Interface Role RCF-reject
---------------- ------------- ------------
port-channel 1 Downstream Disabled
---------------- ------------- ------------ |
| MDS9216 (Canterbury) |
|---|
canterbury# sh int gig 2/1-2
GigabitEthernet2/1 is up
Hardware is GigabitEthernet, address is 0005.3000.ade6
Internet address is 200.200.200.1/30
MTU 3000 bytes
Port mode is IPS
Speed is 1 Gbps
Beacon is turned off
Auto-Negotiation is turned on
5 minutes input rate 320 bits/sec, 40 bytes/sec, 0 frames/sec
5 minutes output rate 320 bits/sec, 40 bytes/sec, 0 frames/sec
8844 packets input, 993118 bytes
0 multicast frames, 0 compressed
0 input errors, 0 frame, 0 overrun 0 fifo
8855 packets output, 994686 bytes, 0 underruns
0 output errors, 0 collisions, 0 fifo
0 carrier errors
GigabitEthernet2/2 is up
Hardware is GigabitEthernet, address is 0005.3000.ade7
Internet address is 200.200.200.5/30
MTU 3000 bytes
Port mode is IPS
Speed is 1 Gbps
Beacon is turned off
Auto-Negotiation is turned on
5 minutes input rate 16 bits/sec, 2 bytes/sec, 0 frames/sec
5 minutes output rate 8 bits/sec, 1 bytes/sec, 0 frames/sec
634 packets input, 39538 bytes
0 multicast frames, 0 compressed
0 input errors, 0 frame, 0 overrun 0 fifo
610 packets output, 47264 bytes, 0 underruns
0 output errors, 0 collisions, 0 fifo
0 carrier errors
canterbury# sh ips stats tcp int gig 2/1
TCP Statistics for port GigabitEthernet2/1
Connection Stats
18 active openings, 10 accepts
14 failed attempts, 0 reset received, 8 established
Segment stats
8919 received, 8923 sent, 0 retransmitted
0 bad segments received, 0 reset sent
TCP Active Connections
Local Address Remote Address State Send-Q Recv-Q
200.200.200.1:3225 100.100.100.1:65480 ESTABLISH 0 0
200.200.200.1:3225 100.100.100.1:65482 ESTABLISH 0 0
200.200.200.1:3225 0.0.0.0:0 LISTEN 0 0
canterbury# sh ips stats tcp int gig 2/2
TCP Statistics for port GigabitEthernet2/2
Connection Stats
498 active openings, 2 accepts
498 failed attempts, 0 reset received, 2 established
Segment stats
556 received, 579 sent, 0 retransmitted
0 bad segments received, 0 reset sent
TCP Active Connections
Local Address Remote Address State Send-Q Recv-Q
200.200.200.5:3225 100.100.100.5:65531 ESTABLISH 0 0
200.200.200.5:3225 100.100.100.5:65533 ESTABLISH 0 0
200.200.200.5:3225 0.0.0.0:0 LISTEN 0 0
canterbury# sh int fcip 1-2
fcip1 is trunking
Hardware is GigabitEthernet
Port WWN is 20:42:00:0c:30:6c:24:40
Peer port WWN is 20:c2:00:05:30:00:7a:de
Admin port mode is auto, trunk mode is auto
Port mode is TE
vsan is 1
Belongs to port-channel 2
Trunk vsans (allowed active) (600-601)
Trunk vsans (operational) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
Using Profile id 200 (interface GigabitEthernet2/1)
Peer Information
Peer Internet address is 100.100.100.1 and port is 3225
Special Frame is disabled
Maximum number of TCP connections is 2
Time Stamp is disabled
QOS control code point is 0
QOS data code point is 0
B-port mode disabled
TCP Connection Information
2 Active TCP connections
Control connection: Local 200.200.200.1:3225, Remote 100.100.100.1:65480
Data connection: Local 200.200.200.1:3225, Remote 100.100.100.1:65482
18 Attempts for active connections, 2 close of connections
TCP Parameters
Path MTU 3000 bytes
Current retransmission timeout is 200 ms
Round trip time: Smoothed 5 ms, Variance: 6
Advertized window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Congestion window: Current: 10 KB, Slow start threshold: 112 KB
5 minutes input rate 136 bits/sec, 17 bytes/sec, 0 frames/sec
5 minutes output rate 136 bits/sec, 17 bytes/sec, 0 frames/sec
4189 frames input, 391368 bytes
4183 Class F frames input, 390668 bytes
6 Class 2/3 frames input, 700 bytes
0 Error frames timestamp error 0
4189 frames output, 390140 bytes
4183 Class F frames output, 389404 bytes
6 Class 2/3 frames output, 736 bytes
0 Error frames 0 reass frames
fcip2 is trunking
Hardware is GigabitEthernet
Port WWN is 20:46:00:0c:30:6c:24:40
Peer port WWN is 20:c6:00:05:30:00:7a:de
Admin port mode is auto, trunk mode is auto
Port mode is TE
vsan is 1
Belongs to port-channel 2
Trunk vsans (allowed active) (600-601)
Trunk vsans (operational) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
Using Profile id 201 (interface GigabitEthernet2/2)
Peer Information
Peer Internet address is 100.100.100.5 and port is 3225
Special Frame is disabled
Maximum number of TCP connections is 2
Time Stamp is disabled
QOS control code point is 0
QOS data code point is 0
B-port mode disabled
TCP Connection Information
2 Active TCP connections
Control connection: Local 200.200.200.5:3225, Remote 100.100.100.5:65531
Data connection: Local 200.200.200.5:3225, Remote 100.100.100.5:65533
498 Attempts for active connections, 0 close of connections
TCP Parameters
Path MTU 3000 bytes
Current retransmission timeout is 200 ms
Round trip time: Smoothed 10 ms, Variance: 5
Advertized window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Congestion window: Current: 8 KB, Slow start threshold: 112 KB
5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
8 frames input, 1228 bytes
8 Class F frames input, 1228 bytes
0 Class 2/3 frames input, 0 bytes
0 Error frames timestamp error 0
8 frames output, 1232 bytes
8 Class F frames output, 1232 bytes
0 Class 2/3 frames output, 0 bytes
0 Error frames 0 reass frames
canterbury# sh int port 2
port-channel 2 is trunking
Hardware is Fibre Channel
Port WWN is 24:02:00:0c:30:6c:24:40
Admin port mode is auto, trunk mode is auto
Port mode is TE
Port vsan is 1
Speed is 2 Gbps
Trunk vsans (admin allowed and active) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
5 minutes input rate 120 bits/sec, 15 bytes/sec, 0 frames/sec
5 minutes output rate 120 bits/sec, 15 bytes/sec, 0 frames/sec
4213 frames input, 394068 bytes
4207 Class F frames input, 393368 bytes
6 Class 2/3 frames input, 700 bytes
0 Error frames timestamp error 0
4213 frames output, 392844 bytes
4207 Class F frames output, 392108 bytes
6 Class 2/3 frames output, 736 bytes
0 Error frames 0 reass frames
Member[1] : fcip1
Member[2] : fcip2
canterbury# sh ips ip route interface gig 2/1
Codes: C - connected, S - static
No default gateway
S 100.100.100.0/30 via 200.200.200.2, GigabitEthernet2/1
C 200.200.200.0/30 is directly connected, GigabitEthernet2/1
canterbury# sh ips ip route interface gig 2/2
Codes: C - connected, S - static
No default gateway
S 100.100.100.4/30 via 200.200.200.6, GigabitEthernet2/2
C 200.200.200.4/30 is directly connected, GigabitEthernet2/2
canterbury# sh fcns da
VSAN 600:
--------------------------------------------------------------------------
FCID TYPE PWWN (VENDOR) FC4-TYPE:FEATURE
--------------------------------------------------------------------------
0x010001 N 10:00:00:00:c9:32:a6:e3 (Emulex) scsi-fcp:init
0x020001 N 50:05:07:63:00:d0:94:4c (IBM) scsi-fcp:target fc..
Total number of entries = 2
VSAN 601:
--------------------------------------------------------------------------
FCID TYPE PWWN (VENDOR) FC4-TYPE:FEATURE
--------------------------------------------------------------------------
0x010100 N 10:00:00:00:00:05:00:00
0x020100 N 10:00:00:00:00:01:00:00
!--- Always verify that the fabric has formed with the expected neighbor(s) !--- through FCIP E or TE port when the configuration is completed.
|
| 特殊帧配置(Bison) |
|---|
!--- Special frames are used to improve security. !--- Before user-data is transmitted across an FCIP tunnel, FSF verifies that !--- the peer is defined on the configured wwn.
interface fcip1
channel-group 1 force
no shutdown
use-profile 1
peer-info ipaddr 200.200.200.1
special-frame peer-wwn 20:00:00:0c:30:6c:24:40 profile-id 200
interface fcip2
channel-group 1 force
no shutdown
use-profile 2
peer-info ipaddr 200.200.200.5
special-frame peer-wwn 20:00:00:0c:30:6c:24:40 profile-id 201
!--- The peer-wwn is derived from the peer MDS by issuing the following command:
canterbury# sh wwn switch
Switch WWN is 20:00:00:0c:30:6c:24:40
!--- This value is significant per peer switch, so it is used for all tunnels !--- towards this switch. This configuration shows the following:
bison# sh int fcip 1-2
fcip1 is trunking
Hardware is GigabitEthernet
Port WWN is 20:c2:00:05:30:00:7a:de
Peer port WWN is 20:42:00:0c:30:6c:24:40
Admin port mode is auto, trunk mode is on
Port mode is TE
vsan is 1
Belongs to port-channel 1
Trunk vsans (allowed active) (600-601)
Trunk vsans (operational) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
Using Profile id 1 (interface GigabitEthernet4/1)
Peer Information
Peer Internet address is 200.200.200.1 and port is 3225
Special Frame is enabled
Peer switch WWN is 20:00:00:0c:30:6c:24:40
Peer profile id is 200
Maximum number of TCP connections is 2
Time Stamp is disabled
QOS control code point is 0
QOS data code point is 0
B-port mode disabled
TCP Connection Information
2 Active TCP connections
Control connection: Local 100.100.100.1:65372, Remote 200.200.200.1:3225
Data connection: Local 100.100.100.1:65374, Remote 200.200.200.1:3225
82 Attempts for active connections, 9 close of connections
TCP Parameters
Path MTU 3000 bytes
Current retransmission timeout is 200 ms
Round trip time: Smoothed 2 ms, Variance: 1
Advertized window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Congestion window: Current: 106 KB, Slow start threshold: 118 KB
5 minutes input rate 46128 bits/sec, 5766 bytes/sec, 19 frames/sec
5 minutes output rate 194867736 bits/sec, 24358467 bytes/sec, 20732 frames/sec
5841 frames input, 1729836 bytes
4575 Class F frames input, 429444 bytes
1266 Class 2/3 frames input, 1300392 bytes
0 Error frames timestamp error 0
6339146 frames output, 7447938520 bytes
4576 Class F frames output, 431800 bytes
6334570 Class 2/3 frames output, 7447506720 bytes
0 Error frames 0 reass frames
fcip2 is trunking
Hardware is GigabitEthernet
Port WWN is 20:c6:00:05:30:00:7a:de
Peer port WWN is 20:46:00:0c:30:6c:24:40
Admin port mode is auto, trunk mode is on
Port mode is TE
vsan is 1
Belongs to port-channel 1
Trunk vsans (allowed active) (600-601)
Trunk vsans (operational) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
Using Profile id 2 (interface GigabitEthernet4/2)
Peer Information
Peer Internet address is 200.200.200.5 and port is 3225
Special Frame is enabled
Peer switch WWN is 20:00:00:0c:30:6c:24:40
Peer profile id is 201
Maximum number of TCP connections is 2
Time Stamp is disabled
QOS control code point is 0
QOS data code point is 0
B-port mode disabled
TCP Connection Information
2 Active TCP connections
Control connection: Local 100.100.100.5:3225, Remote 200.200.200.5:64535
Data connection: Local 100.100.100.5:3225, Remote 200.200.200.5:64537
58 Attempts for active connections, 1 close of connections
TCP Parameters
Path MTU 3000 bytes
Current retransmission timeout is 200 ms
Round trip time: Smoothed 2 ms, Variance: 1
Advertized window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Congestion window: Current: 106 KB, Slow start threshold: 112 KB
5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
415 frames input, 398160 bytes
16 Class F frames input, 2460 bytes
399 Class 2/3 frames input, 395700 bytes
0 Error frames timestamp error 0
6078322 frames output, 7147327176 bytes
16 Class F frames output, 2460 bytes
6078306 Class 2/3 frames output, 7147324716 bytes
0 Error frames 0 reass frames |
| 特殊帧配置(Canterbury) |
|---|
interface fcip1
channel-group 2 force
no shutdown
use-profile 200
peer-info ipaddr 100.100.100.1
special-frame peer-wwn 20:00:00:05:30:00:7a:de profile-id 1
interface fcip2
channel-group 2 force
no shutdown
use-profile 201
peer-info ipaddr 100.100.100.5
special-frame peer-wwn 20:00:00:05:30:00:7a:de profile-id 2
canterbury# sh int fcip 1
fcip1 is trunking
Hardware is GigabitEthernet
Port WWN is 20:42:00:0c:30:6c:24:40
Peer port WWN is 20:c2:00:05:30:00:7a:de
Admin port mode is auto, trunk mode is auto
Port mode is TE
vsan is 1
Belongs to port-channel 2
Trunk vsans (allowed active) (600-601)
Trunk vsans (operational) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
Using Profile id 200 (interface GigabitEthernet2/1)
Peer Information
Peer Internet address is 100.100.100.1 and port is 3225
Special Frame is enabled
Peer switch WWN is 20:00:00:05:30:00:7a:de
Peer profile id is 1
Maximum number of TCP connections is 2
Time Stamp is disabled
QOS control code point is 0
QOS data code point is 0
B-port mode disabled
TCP Connection Information
2 Active TCP connections
Control connection: Local 200.200.200.1:3225, Remote 100.100.100.1:65372
Data connection: Local 200.200.200.1:3225, Remote 100.100.100.1:65374
2 Attempts for active connections, 0 close of connections
TCP Parameters
Path MTU 3000 bytes
Current retransmission timeout is 200 ms
Round trip time: Smoothed 2 ms, Variance: 1
Advertized window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Congestion window: Current: 10 KB, Slow start threshold: 112 KB
5 minutes input rate 94347400 bits/sec, 11793425 bytes/sec, 10031 frames/sec
5 minutes output rate 144 bits/sec, 18 bytes/sec, 0 frames/sec
3985861 frames input, 4685834196 bytes
219 Class F frames input, 25228 bytes
3985642 Class 2/3 frames input, 4685808968 bytes
0 Error frames timestamp error 0
1043 frames output, 866780 bytes
218 Class F frames output, 23448 bytes
825 Class 2/3 frames output, 843332 bytes
0 Error frames 0 reass frames
canterbury# sh int fcip 2
fcip2 is trunking
Hardware is GigabitEthernet
Port WWN is 20:46:00:0c:30:6c:24:40
Peer port WWN is 20:c6:00:05:30:00:7a:de
Admin port mode is auto, trunk mode is auto
Port mode is TE
vsan is 1
Belongs to port-channel 2
Trunk vsans (allowed active) (600-601)
Trunk vsans (operational) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
Using Profile id 201 (interface GigabitEthernet2/2)
Peer Information
Peer Internet address is 100.100.100.5 and port is 3225
Special Frame is enabled
Peer switch WWN is 20:00:00:05:30:00:7a:de
Peer profile id is 2
Maximum number of TCP connections is 2
Time Stamp is disabled
QOS control code point is 0
QOS data code point is 0
B-port mode disabled
TCP Connection Information
2 Active TCP connections
Control connection: Local 200.200.200.5:64535, Remote 100.100.100.5:3225
Data connection: Local 200.200.200.5:64537, Remote 100.100.100.5:3225
500 Attempts for active connections, 0 close of connections
TCP Parameters
Path MTU 3000 bytes
Current retransmission timeout is 300 ms
Round trip time: Smoothed 10 ms, Variance: 5
Advertized window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Congestion window: Current: 8 KB, Slow start threshold: 118 KB
5 minutes input rate 94399712 bits/sec, 11799964 bytes/sec, 10034 frames/sec
5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
9769115 frames input, 11486944196 bytes
16 Class F frames input, 2460 bytes
9769099 Class 2/3 frames input, 11486941736 bytes
0 Error frames timestamp error 0
415 frames output, 398160 bytes
16 Class F frames output, 2460 bytes
399 Class 2/3 frames output, 395700 bytes
0 Error frames 0 reass frames |
| 从Bison和Canterbury - Canterbury被动显示 |
|---|
interface fcip1
channel-group 2 force
no shutdown
use-profile 200
passive-mode
peer-info ipaddr 100.100.100.1
special-frame peer-wwn 20:00:00:05:30:00:7a:de profile-id 1
interface fcip2
channel-group 2 force
no shutdown
use-profile 201
passive-mode
peer-info ipaddr 100.100.100.5
special-frame peer-wwn 20:00:00:05:30:00:7a:de profile-id 2
canterbury# sh ips stats tcp int gig 2/1
TCP Statistics for port GigabitEthernet2/1
Connection Stats
20 active openings, 14 accepts
14 failed attempts, 0 reset received, 14 established
Segment stats
12042719 received, 3181301 sent, 0 retransmitted
0 bad segments received, 0 reset sent
TCP Active Connections
Local Address Remote Address State Send-Q Recv-Q
200.200.200.1:3225 100.100.100.1:65368 ESTABLISH 0 0
200.200.200.1:3225 100.100.100.1:65370 ESTABLISH 0 0
200.200.200.1:3225 100.100.100.1:65372 TIME_WAIT 0 0
200.200.200.1:3225 0.0.0.0:0 LISTEN 0 0
!--- Both FCIP interfaces for Canterbury are configured to be passive; this !--- results in the above TCP statistics where Canterbury, despite being !--- configured with the highest IP addresses for both tunnels, did not !--- initiate the TCP connections. Its peer, Bison, initiates.
canterbury# sh ips stats tcp int gig 2/2
TCP Statistics for port GigabitEthernet2/2
Connection Stats
500 active openings, 4 accepts
498 failed attempts, 0 reset received, 6 established
Segment stats
11933351 received, 3144627 sent, 0 retransmitted
0 bad segments received, 0 reset sent
TCP Active Connections
Local Address Remote Address State Send-Q Recv-Q
200.200.200.5:3225 100.100.100.5:65415 ESTABLISH 0 0
200.200.200.5:3225 100.100.100.5:65417 ESTABLISH 0 0
200.200.200.5:64535 100.100.100.5:3225 TIME_WAIT 0 0
200.200.200.5:3225 0.0.0.0:0 LISTEN 0 0 |
| 从Bison和Canterbury显示 — 时间戳设置 |
|---|
!--- FCIP Time Stamp is enabled to allow the peer to drop FCIP userdata if it !--- exceeds the specified time-difference. The time difference is the maximum !--- value in transit of user data frames between two peer FCIP entities.
bison(config-if)# time-stamp acceptable-diff 1000
Please enable NTP with a common time source on both MDS Switches that are on
either side of the FCIP link
!--- Note that the value specified is in milliseconds and, because a !--- time difference is specified, both ends of the FCIP tunnel must have access !--- to the same clock source through NTP.
interface fcip1
channel-group 1 force
no shutdown
use-profile 1
peer-info ipaddr 200.200.200.1
time-stamp acceptable-diff 1000
special-frame peer-wwn 20:00:00:0c:30:6c:24:40 profile-id 200
interface fcip2
channel-group 1 force
no shutdown
use-profile 2
peer-info ipaddr 200.200.200.5
time-stamp acceptable-diff 1000
special-frame peer-wwn 20:00:00:0c:30:6c:24:40 profile-id 201
bison# sh int fcip 1
fcip1 is trunking
Hardware is GigabitEthernet
Port WWN is 20:c2:00:05:30:00:7a:de
Peer port WWN is 20:42:00:0c:30:6c:24:40
Admin port mode is auto, trunk mode is on
Port mode is TE
vsan is 1
Belongs to port-channel 1
Trunk vsans (allowed active) (600-601)
Trunk vsans (operational) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
Using Profile id 1 (interface GigabitEthernet4/1)
Peer Information
Peer Internet address is 200.200.200.1 and port is 3225
Special Frame is enabled
Peer switch WWN is 20:00:00:0c:30:6c:24:40
Peer profile id is 200
Maximum number of TCP connections is 2
Time Stamp is enabled, acceptable time difference 1000 ms
QOS control code point is 0
QOS data code point is 0
B-port mode disabled
TCP Connection Information
2 Active TCP connections
Control connection: Local 100.100.100.1:65368, Remote 200.200.200.1:3225
Data connection: Local 100.100.100.1:65370, Remote 200.200.200.1:3225
84 Attempts for active connections, 10 close of connections
TCP Parameters
Path MTU 3000 bytes
Current retransmission timeout is 200 ms
Round trip time: Smoothed 2 ms, Variance: 3
Advertized window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Congestion window: Current: 10 KB, Slow start threshold: 118 KB
5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
5988 frames input, 1743840 bytes
4719 Class F frames input, 443184 bytes
1269 Class 2/3 frames input, 1300656 bytes
0 Error frames timestamp error 0
15337275 frames output, 18028320932 bytes
4720 Class F frames output, 445544 bytes
15332555 Class 2/3 frames output, 18027875388 bytes
0 Error frames 0 reass frames
canterbury(config-if)# time-stamp acceptable-diff 1000
Please enable NTP with a common time source on both MDS Switches that are on
either side of the FCIP link
interface fcip1
channel-group 2 force
no shutdown
use-profile 200
passive-mode
peer-info ipaddr 100.100.100.1
time-stamp acceptable-diff 1000
special-frame peer-wwn 20:00:00:05:30:00:7a:de profile-id 1
interface fcip2
channel-group 2 force
no shutdown
use-profile 201
passive-mode
peer-info ipaddr 100.100.100.5
time-stamp acceptable-diff 1000
special-frame peer-wwn 20:00:00:05:30:00:7a:de profile-id 2
canterbury# sh int fcip 1
fcip1 is trunking
Hardware is GigabitEthernet
Port WWN is 20:42:00:0c:30:6c:24:40
Peer port WWN is 20:c2:00:05:30:00:7a:de
Admin port mode is auto, trunk mode is auto
Port mode is TE
vsan is 1
Belongs to port-channel 2
Trunk vsans (allowed active) (600-601)
Trunk vsans (operational) (600-601)
Trunk vsans (up) (600-601)
Trunk vsans (isolated) ()
Trunk vsans (initializing) ()
Using Profile id 200 (interface GigabitEthernet2/1)
Peer Information
Peer Internet address is 100.100.100.1 and port is 3225
Passive mode is enabled
Special Frame is enabled
Peer switch WWN is 20:00:00:05:30:00:7a:de
Peer profile id is 1
Maximum number of TCP connections is 2
Time Stamp is enabled, acceptable time difference 1000 ms
QOS control code point is 0
QOS data code point is 0
B-port mode disabled
TCP Connection Information
2 Active TCP connections
Control connection: Local 200.200.200.1:3225, Remote 100.100.100.1:65368
Data connection: Local 200.200.200.1:3225, Remote 100.100.100.1:65370
2 Attempts for active connections, 0 close of connections
TCP Parameters
Path MTU 3000 bytes
Current retransmission timeout is 200 ms
Round trip time: Smoothed 6 ms, Variance: 6
Advertized window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
Congestion window: Current: 10 KB, Slow start threshold: 112 KB
5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
9427366 frames input, 11084654892 bytes
295 Class F frames input, 32716 bytes
9427071 Class 2/3 frames input, 11084622176 bytes
145359 Error frames timestamp error 145359
1122 frames output, 874528 bytes
294 Class F frames output, 30932 bytes
828 Class 2/3 frames output, 843596 bytes
0 Error frames 0 reass frames |
反馈