uBR10012启动顺序

下载选项

  • PDF     (229.2 KB)
    在各种设备上使用 Adobe Reader 查看
  • ePub     (81.9 KB)
    在 iPhone、iPad、Android、Sony Reader 或 Windows Phone 上使用各种应用查看
  • Mobi (Kindle)     (68.7 KB)
    在 Kindle 设备上查看或在多个设备上使用 Kindle 应用查看
已更新: 2005 年 10 月 4 日
文档 ID:3982

非歧视性语言

此产品的文档集力求使用非歧视性语言。在本文档集中，非歧视性语言是指不隐含针对年龄、残障、性别、种族身份、族群身份、性取向、社会经济地位和交叉性的歧视的语言。由于产品软件的用户界面中使用的硬编码语言、基于 RFP 文档使用的语言或引用的第三方产品使用的语言，文档中可能无法确保完全使用非歧视性语言。 深入了解思科如何使用包容性语言。

关于此翻译

思科采用人工翻译与机器翻译相结合的方式将此文档翻译成不同语言，希望全球的用户都能通过各自的语言得到支持性的内容。 请注意：即使是最好的机器翻译，其准确度也不及专业翻译人员的水平。 Cisco Systems, Inc. 对于翻译的准确性不承担任何责任，并建议您总是参考英文原始文档（已提供链接）。

简介

本文档介绍从性能路由引擎(PRE)到射频(RF)、LAN、WAN以及Timing、Communications和Control Plus(TCC+)卡的Cisco uBR10000系列通用宽带路由器的启动顺序。

先决条件

要求

本文档的读者应掌握以下这些主题的相关知识：

  • 基本的思科路由器架构

  • Cisco IOS®软件命令行界面

使用的组件

本文档中的信息基于以下软件和硬件版本：

  • Cisco ucBr10012 通用宽带路由器

  • 用于uBR10000系列(UBR10K-P6-M)的思科IOS软件

本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始（默认）配置。如果您使用的是真实网络，请确保您已经了解所有命令的潜在影响。

规则

有关文件规则的更多信息请参见“ Cisco技术提示规则”。

PRE启动顺序

PRE的启动顺序有以下不同步骤：

  1. 加载引导助手。

    c10k-eboot-mz.120-16.6.ST1

    这不支持任何线卡；只有PRE上的快速以太网(FE)接口可用。

  2. 加载主映像。

    ubr10k-p6-mz.122-1.XF
ubr10k-k8p6-mz.122-1.XF

    每种类型的线卡轮询PRE以获取固件：

    • 电缆线卡

    • TCC+

    • 烤面包机

    • 千兆以太网

    • 光载波12(OC-12)加电服务(POS)

此输出显示实际实时启动序列及其日志消息：

System Bootstrap, Version 12.0(9r)SL2, RELEASE SOFTWARE (fc1)

!--- Bootstrap version.

Copyright (c) 2000 by cisco Systems, Inc.
Reset Reason Register = RESET_REASON_RESET_REG (0x76)

!--- Reason for reload: RESET.

C10000 platform with 524288 Kbytes of main memory

Self decompressing the image :
#################################################
################################################
Self decompressing the image :
#################################################
################################################
Self decompressing the image :
#################################################
################################################
Self decompressing the image :
#################################################
################################################
Self decompressing the image :
#################################################
################################################
Self decompressing the image :
#################################################
#####
[OK]

Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706 
 
Cisco Internetwork Operating System Software
IOS (tm) 10000 Software (UBR10K-P6-M), Version 12.2(1)XF, EARLY
DEPLOYMENT RELEASE SOFTWARE (fc1)

!--- Main image.

TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Fri 18-May-01 16:15 by ccai
Image text-base: 0x60008960, data-base: 0x612E0000
cisco uBR10000 (PRE-RP) processor with 393215K/131072K bytes of memory.

!--- Processor type.

Processor board ID TBA05100542
R7000 CPU at 262Mhz, Implementation 39, Rev 2.1, 256KB L2, 2048KB L3 Cache
Backplane version 1.0, 8 slot
Last reset from register reset
Toaster processor tmc0 is running.
Toaster processor tmc1 is running.
1 Ethernet/IEEE 802.3 interface(s)
1 FastEthernet/IEEE 802.3 interface(s)
509K bytes of non-volatile configuration memory.
46976K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
32768K bytes of Flash internal SIMM (Sector size 256KB).

00:00:15: Downloading Microcode: file=system:pxf/c10k102-3.ucode,
version=102.3(40.4),
description=Experimental Software created Wed 31-Jan-01 16:22 by clauer
in view clauer-omega_dev

!--- Microcode for Parallel eXpress Forwarding (PXF) engine.

00:00:16: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram
00:00:22: %LINK-3-UPDOWN: Interface Ethernet0/0/0, changed state to up

!--- 10Base2 interface.

00:00:22: %LINK-5-CHANGED: Interface FastEthernet0/0/0, changed state to reset

!--- Management FE interface. !--- Each of these lines of output appear on one line:

00:00:23: %UBR10000-5-USFREQCHG: Interface Cable6/1/0 Port U0,
          frequency changed to 34.992 MHz
00:00:23: %UBR10000-5-UPDOWN: Interface Cable6/1/0 Port U0,
          changed state to down
00:00:23: %UBR10000-5-UPDOWN: Interface Cable6/1/0 Port U1,
          changed state to down
00:00:23: %UBR10000-5-UPDOWN: Interface Cable6/1/0 Port U2,
          changed state to down
00:00:23: %UBR10000-5-UPDOWN: Interface Cable6/1/0 Port U3,
          changed state to down
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0/0,
          changed state to up
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0/0,
          changed state to down
00:00:25: %LINK-5-CHANGED: Interface POS2/0/0,
          changed state to administratively down
00:00:25: %LINK-5-CHANGED: Interface GigabitEthernet4/0/0,
          changed state to administratively down
00:00:26: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS2/0/0,
          changed state to down
00:00:26: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4/0/0,
          changed state to down
00:00:29: !!pxf clients started, forwarding code operational!!

!--- The PFX engine microcode is decompressed and executed.

00:00:30: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 10000 Software (UBR10K-P6-M), Version 12.2(1)XF, EARLY
DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Fri 18-May-01 16:15 by ccai
00:00:30: %SYS-6-BOOTTIME: Time taken to reboot after reload = 349 seconds

!--- The time taken to boot after the reload initiated.

00:00:31: %LINK-3-UPDOWN: Interface FastEthernet0/0/0,
          changed state to up
00:00:32: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0/0,
          changed state to up
00:00:34: %IPCOIR-5-CARD_DETECTED: Card type 2cable-mc28 (0x254)
          in slot 6/1

!--- RF card registration request received.

00:00:34: %IPCOIR-5-CARD_DETECTED: Card type 2cable-mc28 (0x254)
          in slot 7/0

!--- RF card registration request received.

00:00:34: %IPCOIR-5-CARD_LOADING: Loading card in slot 6/1

!--- TFTP is used to transfer the RF card microcode.

00:00:34: %IPCOIR-5-CARD_LOADING: Loading card in slot 7/0

!--- TFTP is used to transfer the RF card microcode.

00:00:34: %IPCOIR-5-CARD_DETECTED: Card type 2cable-tccplus (0x2AF)
          in slot 1/1

!--- TCC+ registration request received.

00:00:34: %IPCOIR-5-CARD_DETECTED: Card type 1oc12pos-1 (0x164)
          in slot 2/0

!--- LAN to WAN registration received.

00:00:34: %IPCOIR-5-CARD_DETECTED: Card type 1gigethernet-1 (0x166)
          in slot 4/0

!--- LAN to WAN registration received.

00:00:34: %IPCOIR-2-CARD_UP_DOWN: Card in slot 1/1 is up.
          Notifying 2cable-tccplus driver.
00:00:34: %IPCOIR-2-CARD_UP_DOWN: Card in slot 2/0 is up.
          Notifying 1oc12pos-1 driver.
00:00:34: %UBR10KTCC-2-ACTIVE_TCC: TCCplus card 1/1 is active
          with Local oscillator as clock reference
00:00:35: %IPCOIR-2-CARD_UP_DOWN: Card in slot 4/0 is up.
          Notifying 1gigethernet-1 driver.
00:00:35: %C10KGE-6-GBIC_OK: Interface GigabitEthernet4/0/0,
          1000BASE-SX Gigabit Interface Converter (GBIC) inserted

RF线卡启动顺序

RF线卡的启动顺序有以下不同步骤：

  1. ROM Monitor(ROMmon)在线卡中加载引导助手。

  2. 引导助手发送软件版本号和卡类型。

  3. PRE下载与卡类型对应的映像。

  4. Cisco IOS软件映像将解压并执行。

  5. 设置Ba接口，以便数据可以传送到PRE。

brubeck# debug ipc events

Special Events debugging is on
*Aug  1 05:12:10.596: IPC: Registration request for seat 'clc_6_1'

!--- The RF line card requests registration with the software version !--- number and the line card type.

*Aug  1 05:12:10.604: IPC: Got an open port request for port 0x10008
*Aug  1 05:12:10.604: IPC: Got an open port request for port 0x10009
1w1d: %IPCOIR-5-CARD_DETECTED: Card type 2cable-mc28 (0x254) in slot 6/1

!--- The card type is detected.

1w1d: %IPCOIR-2-CARD_UP_DOWN: Card in slot 6/1 is up.
                              Notifying 2cable-mc28 driver.

!--- Microcode for the RF line card.

SLOT 6/1: 00:00:16: %IPCGRP-6-UCODEVER: Reported microcode version, 990227862.
SLOT 6/1: 00:00:16: %IPCGRP-6-INTENBDISAB: Interface disabled
<REMOVED>

!--- The main image is downloaded, decompressed, and executed.

SLOT 6/1: 00:00:19: %IPCGRP-6-BARENBDISAB: Barium interface enabled

!--- Enable Barium interface.

1w1d: %LINK-3-UPDOWN: Interface Cable6/1/1, changed state to up
SLOT 6/1: 00:00:20: %LINK-3-UPDOWN: Interface Cable6/1/1, changed state to up
SLOT 6/1: 00:00:20: %LINK-3-UPDOWN: Interface Barium3/0, changed state to up

!--- The Barium interface is set to up.

1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cable6/1/1,
                           changed state to up
1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cable6/1/0,
                           changed state to up
SLOT 6/1: 00:00:21: %LINEPROTO-5-UPDOWN: Line protocol on Interface Barium3/0,
                                         changed state to up

!--- The Barium line protocol is up and can now pass data to the PRE.

引导帮助程序继续将软件版本号和卡类型作为keepalive发送。如果在PRE上升级微码，则会下载新的微码并自动进行升级。

LAN或WAN卡引导顺序

LAN或WAN卡的启动顺序有以下不同步骤：

  1. 线路卡使用软件版本号和卡类型请求注册。

  2. PRE下载与卡类型对应的映像。

  3. Cisco IOS软件映像将解压并执行。

brubeck# debug ipc events

Special Events debugging is on
*Aug  1 05:08:01.496: IPC: Registration request for seat
                           'C10K Line Card slot 2/0'

!--- The LAN or WAN card requests registration with the software !--- version and the card type.

*Aug  1 05:08:01.500: IPC: Got an open port request for port 0x10008
1w1d: %IPCOIR-5-CARD_DETECTED: Card type 1oc12pos-1 (0x164) in slot 2/0

!--- The card type is detected.

1w1d: %IPCOIR-5-CARD_LOADING: Loading card in slot 2/0

!--- TFTP is used to transfer the microcode to the line card.

1w1d: %C10K-5-LC_NOTICE: Slot[2/0] 1oc12pos-1 Image
Downloaded...Booting...

!--- The image is decompressed and the code is executed.

TCC+卡启动顺序

TCC+卡的启动顺序有以下不同步骤：

  1. TCC+卡使用软件版本号和卡类型请求注册。

  2. PRE下载与卡类型对应的映像。

  3. Cisco IOS软件映像解压并执行

brubeck# debug ipc events

Special Events debugging is on
*Aug  1 07:00:40.751: IPC: Registration request for seat
                           'C10K Line Card slot 1/1'

!--- The TCC+ card requests registration.

*Aug  1 07:00:40.755: IPC: Got an open port request for port 0x10008
1w1d: %IPCOIR-5-CARD_DETECTED: Card type 2cable-tccplus (0x2AF) in slot 1/1

!--- The card type is detected.

1w1d: %IPCOIR-5-CARD_LOADING: Loading card in slot 1/1

!--- TFTP is used to transfer the microcode to the TCC+ card.

1w1d: %C10K-5-LC_NOTICE: Slot[1/1] utility-card Image
Downloaded...Booting...

!--- The image is decompressed and the code is executed.

1w1d: %IPCOIR-5-CARD_DETECTED: Card type 2cable-tccplus (0x2AF) in slot 1/1
1w1d: %IPCOIR-2-CARD_UP_DOWN: Card in slot 1/1 is up.
                              Notifying 2cable-tccplus driver.
1w1d: %UBR10KTCC-2-ACTIVE_TCC: TCCplus card 1/1 is active
                               with Local oscillator as clock reference

!--- The card is active and reports its clock source.

相关信息

此文档是否有帮助?

Feedback反馈

联系我们

本文档适用于以下产品