E&M Digital CAS 信令的 EM_PARK 问题疑难解答

简介

在Cisco 2600、3600和MC3810路由器平台上的数字E&M信令中，某些T1/E1时隙可能停滞在EM_PARK状态。当您发出show voice call summary命令时，可见此处。本文解释如何发现并解决此问题。

此输出显示某些时隙处于EM_PARK状态。EM_PARK状态的时隙不用于语音呼叫。

Router#show voice call summary 
PORT      CODEC     VAD    VTSP STATE     VPM STATE
=====     ======    ===    ==========     ==========
1/0:0.1     -        -          -         EM_ONHOOK 
1/0:0.2     -        -          -         EM_PARK 
1/0:0.3     -        -          -         EM_PARK 
1/0:0.4     -        -          -         EM_ONHOOK 
1/0:0.5     -        -          -         EM_ONHOOK

先决条件

要求

本文档没有任何特定的要求。

使用的组件

本文档中的信息基于以下软件和硬件版本：

• 硬件 — Cisco 2600、Cisco 3600、Cisco VG200和MC3810路由器

• 软件 — 全部

本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始（默认）配置。如果您使用的是真实网络，请确保您已经了解所有命令的潜在影响。

背景理论

在T1 CAS中，例如，闪烁启动信令，当PBX摘机时，路由器/网关端时隙保持空闲(EM_ONHOOK)状态，直到远程目标应答呼叫。当远程目标应答呼叫时，路由器时隙状态将更改为EM_OFFHOOK。

如果呼叫未连接，路由器/网关将向主叫方播放带内重排音。由于路由器端的信道状态仍为EM_ONHOOK，因此路由器无法挂断该信道。呼叫方挂断后，PBX需要将其信道状态从摘机更改为挂机。

在某些情况下，PBX在ABCD过渡的帮助下不发送挂机消息。路由器对此有一种解决方法，称为假应答。如果没有假的答案解决方法，信道将无限期地处于EM_PARK状态。有关详细信息，请参阅“假答案”部分。

注意：如果语音网关路由器机箱未正确接地，则某些T1信道上的呼叫可能会停滞在EM_PARK状态。有关电气接地的详细信息，请参阅硬件安装指南。

规则

有关文档规则的详细信息，请参阅 Cisco 技术提示规则。

问题

时隙停滞在EM_PARK状态可能有两个主要原因：

• 数字信号处理器(DSP)不良，存在硬件或软件问题。

• PSTN交换机/PBX向路由器发送连续摘机信号，但不释放该信号。

解决方案

以下是解决此问题的方法：

如果系统中的时隙停滞在EM_PARK状态，请检查DSP。要检查DSP，请参阅Cisco 2600/3600系列路由器的NM-HDV上的DSP故障排除。

如果DSP处于活动状态，则问题可能出在PSTN交换机/PBX端或Cisco IOS®^{（路由器/网关不启动假应答过程）。} 有关详细信息，请参阅“假答案”部分。

冒充应答

Cisco路由器/网关在播放重新排序音时知道需要从PBX将时隙设置为挂机后，会等待默认值30秒(使用timeouts wait-release 和timeouts call-disconnect 命令来更改这些值)。

如果不发生这种情况，路由器将时隙移至EM_PARK状态，并启动另一个计时器，持续时间为10秒。如果PBX在10秒持续时间后仍不挂机，则路由器会欺骗PBX。路由器发送一秒的假应答，然后挂机。

路由器发送假应答信号后，路由器将启动另一个计时器，时间为5分钟。如果PBX挂机，计时器停止，路由器将时隙转换到EM_ONHOOK状态。否则，在5分钟后，它会发送另一个假应答信号，表示持续时间为1秒。路由器重复此过程，直到PBX挂机。路由器强制PBX清除呼叫。

注意：由于实际呼叫被清除，此应答转换不会更新到任何记帐记录。但是，PBX将其理解为应答，用户可能会在一秒的持续时间呼叫中付费。

如果与处于EM_PARK状态的时隙关联的DSP处于活动状态且运行正常，并且问题仍然存在，请运行debug vpm all和debug vtsp all命令，以查看Cisco IOS是否尝试发送假应答。

注意：您需要运行调试超过五分钟。

注意：在大多数情况下，如果DSP损坏，路由器不执行假应答解决方法。有关详细信息，请参阅Cisco 2600/3600系列路由器NM-HDV上的DSP故障排除。

此调试输出显示了时隙在EM_PARK中如何卡住，以及假应答解决方法如何工作。

Jan 11 17:19:00.767: htsp_dsp_message: SEND/RESP_SIG_STATUS: state=0xC timestamp
=44262 systime=31305235
Jan 11 17:19:00.767: htsp_process_event:
[4/1:1(10), EM_ONHOOK, E_DSP_SIG_1100]em_onhook_offhook htsp_setup_ind

!--- Offhook signal is received from the switch.

Jan 11 17:19:00.767: [4/1:1(10)] get_local_station_id calling num= calling name=
calling time=01/11 17:19 
Jan 11 17:19:00.767: vtsp_tsp_call_setup_ind (sdb=0x62BB7B14, tdm_info=0x0, tsp_
info=0x62BB4050, calling_number= calling_oct3 = 0x0, called_number= called_oct3 
= 0x81, oct3a=0x0): peer_tag=0
Jan 11 17:19:00.767: : ev.clg.clir is 0
ev.clg.clid_transparent is
0
ev.clg.null_orig_clg is 1
ev.clg.calling_translated is false

Jan 11 17:19:00.767: htsp_timer - 3000 msec
Jan 11 17:19:00.767: vtsp_do_call_setup_ind
Jan 11 17:19:00.767: vtsp_allocate_cdb,cdb 0x62DCEA70
Jan 11 17:19:00.767: vtsp_do_call_setup_ind: Call ID=112722, guid=62DC4230
Jan 11 17:19:00.767: vtsp_do_call_setup_ind: type=0, under_spec=1640890368, 
name=, id0=10, id1=1, id2=25038, calling=, called= subscriber=RegularLine
Jan 11 17:19:00.767: vtsp_do_normal_call_setup_ind
Jan 11 17:19:00.771: cc_api_call_setup_ind (vdbPtr=0x62BB7FA0, 
callInfo={called=
,called_oct3=0x81,calling=,calling_oct3=0x0,calling_oct3a=0x0,calling_xlated=fal
se,subscriber_type_str=RegularLine,fdest=0,peer_tag=0, prog_ind=3},callID=0x62DC
40DC)
Jan 11 17:19:00.771: cc_api_call_setup_ind type 1 , prot 0
Jan 11 17:19:00.771: vtsp_insert_cdb,cdb 0x62DCEA70
Jan 11 17:19:00.771: vtsp_open_voice_and_set_params 
Jan 11 17:19:00.771: dsp_close_voice_channel: [4/1:1:32995] packet_len=8 channel
_id=3 packet_id=75
Jan 11 17:19:00.771: dsp_open_voice_channel_20: [4/1:1:32995] 
packet_len=16 channel_id=3 packet_id=74 alaw_ulaw_select=0 
associated_signaling_channel=130 time_slot=2 serial_port=0
Jan 11 17:19:00.771: vtsp_modem_proto_from_cdb: cap_modem_proto 1073741824
Jan 11 17:19:00.771: vtsp_modem_proto_from_cdb: cap_modem_proto 1073741824
Jan 11 17:19:00.771: dsp_encap_config: [4/1:1:32995] packet_len=30 channel_id=3 
packet_id=92 
TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0
sid_support=1, tse_payload=65535, seq_num=0x0, redundancy=0
Jan 11 17:19:00.771: dsp_set_playout_delay
Jan 11 17:19:00.771: dsp_set_playout: [4/1:1:32995] packet_len=18 channel_id=3 p
acket_id=76 mode=1 initial=60 min=40 max=200 fax_nom=300 
dsp_set_playout_delay_config
Jan 11 17:19:00.771: dsp_set_playout_config
Jan 11 17:19:00.771: mode 0, init 60, min 40, max 200 playout default 
Jan 11 17:19:00.771: dsp_set_playout_config:mode 0, init 60, min 40, max 200 
Jan 11 17:19:00.771: dsp_set_playout_config: [4/1:1:32995] packet_len=18 channel
_id=3 packet_id=76 mode=1 initial=60 min=40 max=200 fax_nom=300 
Jan 11 17:19:00.771: dsp_echo_canceler_control: echo_cancel: 1
Jan 11 17:19:00.771: dsp_echo_canceler_control: [4/1:1:32995] echo_cancel 1, 
disable_hpf 0, flags=0x0, threshold=-21
Jan 11 17:19:00.771: dsp_echo_canceler_control: [4/1:1:32995] packet_len=12 
channel_id=3 packet_id=66 flags=0x0, threshold=-21
Jan 11 17:19:00.771: set_gains: FXx/E&M: msg->message.set_codec_gains.out_gain=0
Jan 11 17:19:00.771: dsp_set_gains: [4/1:1:32995] packet_len=12 channel_id=3 
packet_id=91 in_gain=0 out_gain=0
Jan 11 17:19:00.771: dsp_vad_enable: [4/1:1:32995] enable: packet_len=12 channel
_id=3 packet_id=78 thresh=-38
Jan 11 17:19:00.771: cc_process_call_setup_ind (event=0x62E63ACC)
Jan 11 17:19:00.771: >>>>CCAPI handed cid 32995 with tag 0 to app "DEFAULT"
Jan 11 17:19:00.771: sess_appl: ev(24=CC_EV_CALL_SETUP_IND), cid(32995), disp(0)
Jan 11 17:19:00.771: sess_appl: ev(SSA_EV_CALL_SETUP_IND), cid(32995), disp(0)
Jan 11 17:19:00.771: ssaCallSetupInd 
Jan 11 17:19:00.771: ccCallSetContext (callID=0x80E3, context=0x62DFBCF0)
Jan 11 17:19:00.771: ssaCallSetupInd cid(32995),
 st(SSA_CS_MAPPING),oldst(0), ev
(24)ev->e.evCallSetupInd.nCallInfo.finalDestFlag = 0
Jan 11 17:19:00.771: ccCallSetupAck (callID=0x80E3)
Jan 11 17:19:00.771: ccGenerateTone (callID=0x80E3 tone=8)
Jan 11 17:19:00.771: ccCallReportDigits (callID=0x80E3, enable=0x1)
Jan 11 17:19:00.771: vtsp_report_digit_control: enable=1: 
digit reporting enabled
Jan 11 17:19:00.771: cc_api_call_report_digits_done (vdbPtr=0x62BB7FA0, 
callID=0x80E3, disp=0)
Jan 11 17:19:00.771: : vtsp_get_digit_timeouts
Jan 11 17:19:00.771: sess_appl: ev(52=CC_EV_CALL_REPORT_DIGITS_DONE), 
cid(32995), disp(0)
Jan 11 17:19:00.771: cid(32995)st(SSA_CS_MAPPING)ev
(SSA_EV_CALL_REPORT_DIGITS_DONE)
oldst(SSA_CS_MAPPING)cfid(-1)csize(0)in(1)fDest(0)
Jan 11 17:19:00.771: ssaReportDigitsDone cid(32995) peer list: (empty)
Jan 11 17:19:00.771: ssaReportDigitsDone callid=32995 Enable succeeded
Jan 11 17:19:00.771: ccGenerateTone (callID=0x80E3 tone=8)
Jan 11 17:19:00.771: vtsp:[4/1:1:32995, S_SETUP_INDICATED, E_CC_SETUP_ACK]
Jan 11 17:19:00.775: act_setup_ind_ack 
Jan 11 17:19:00.775: vtsp_modem_proto_from_cdb: cap_modem_proto 0
Jan 11 17:19:00.775: vtsp_modem_proto_from_cdb: cap_modem_proto 0
Jan 11 17:19:00.775: dsp_encap_config: [4/1:1:32995] packet_len=30 channel_id=3 
packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0
sid_support=1, tse_payload=65535, seq_num=0x0, redundancy=0
Jan 11 17:19:00.775: dsp_voice_mode: [4/1:1:32995] cdb 62DCEA70, 
cdb->codec_params.modem 2, inband_detect flags 0x21
Jan 11 17:19:00.775: map_dtmf_relay_type--digit relay mode: 2
Jan 11 17:19:00.775: dsp_voice_mode: [4/1:1:32995] packet_len=24 channel_id=3 
packet_id=73 coding_type=1 voice_field_size=160 VAD_flag=0 
echo_length=256 comfort
_noise=1 inband_detect=33 digit_relay_mode=2 
AGC_flag=0act_setup_ind_ack: modem_mode = 0, fax_relay_on = 1
Jan 11 17:19:00.775: act_setup_ind_ack(): dsp_dtmf_mode()
 dsp_dtmf_mode(VTSP_TONE_DTMF_MODE)

Jan 11 17:19:00.775: dsp_dtmf_mode: [4/1:1:32995] packet_len=10 channel_id=3 
packet_id=65 dtmf_or_mf=0
Jan 11 17:19:00.775: vtsp_timer: 31305236
Jan 11 17:19:00.775: vtsp:[4/1:1:32995, S_DIGIT_COLLECT, E_CC_GEN_TONE]
Jan 11 17:19:00.775: act_gen_tone
Jan 11 17:19:00.775: dsp_cp_tone_off: [4/1:1:32995] packet_len=8 channel_id=3 
packet_id=71
Jan 11 17:19:00.775: dsp_cp_tone_on: [4/1:1:32995] packet_len=38 channel_id=3 
packet_id=72 tone_id=4 n_freq=2 freq_of_first=350 freq_of_second=440 
amp_of_first=5514 amp_of_second=5514 direction=1 on_time_first=65535 
off_time_first=0 on_time_second=0 off_time_second=0
Jan 11 17:19:00.775: vtsp:[4/1:1:32995, S_DIGIT_COLLECT, E_CC_GEN_TONE]
Jan 11 17:19:00.775: act_gen_tone
Jan 11 17:19:00.775: dsp_cp_tone_off: [4/1:1:32995] packet_len=8 channel_id=3 
packet_id=71
Jan 11 17:19:00.775: dsp_cp_tone_on: [4/1:1:32995] packet_len=38 channel_id=3 
packet_id=72 tone_id=4 n_freq=2 freq_of_first=350 freq_of_second=440 
amp_of_first=
5514 amp_of_second=5514 direction=1 on_time_first=65535 off_time_first=0 
on_time4_second=0 off_time_second=0
Jan 11 17:19:00.775: htsp_process_event: [4/1:1(10), EM_WAIT_SETUP_ACK, 
E_HTSP_SETUP_ACK]em_wait_setup_ack_get_ack 
Jan 11 17:19:00.775: htsp_timer_stop 
Jan 11 17:19:00.775: htsp_timer2 - 172 msec
Jan 11 17:19:00.947: htsp_process_event: [4/1:1(10), EM_WAIT_SETUP_ACK, 
E_HTSP_EVENT_TIMER2]em_wait_prewink_timer 
Jan 11 17:19:00.947: em_offhook (0)[recEive and transMit4/1:1(10)] set signal st
ate = 0x8em_onhook (200)[recEive and transMit4/1:1(10)] set signal state = 0x0

!--- A wink of duration 200 msec is sent out to the switch.

Jan 11 17:19:01.471: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=9,
rtp_timestamp=0xED31C493

Jan 11 17:19:01.471: vtsp:[4/1:1:32995, S_DIGIT_COLLECT, E_DSP_DTMF_DIGIT_BEGIN]
Jan 11 17:19:01.471: act_report_digit_begin 
Jan 11 17:19:01.471: cc_api_call_digit_begin (dstVdbPtr=0x0, dstCallId=0xFFFFFFF
F, srcCallId=0x80E3,
digit=9, digit_begin_flags=0x1, rtp_timestamp=0xED31C493 
rtp_expiration=0x0, dest_mask=0x1)
Jan 11 17:19:01.471: sess_appl: ev(10=CC_EV_CALL_DIGIT_BEGIN), cid(32995), disp(0)
Jan 11 17:19:01.471: cid(32995)st(SSA_CS_MAPPING)ev(SSA_EV_DIGIT_BEGIN)
oldst(SSA_CS_MAPPING)cfid(-1)csize(0)in(1)fDest(0)
Jan 11 17:19:01.471: ssaIgnore cid(32995), st(SSA_CS_MAPPING),oldst(0), ev(10)
Jan 11 17:19:01.503: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: 
digit=9, duration=65
Jan 11 17:19:01.503: vtsp:[4/1:1:32995, S_DIGIT_COLLECT, E_DSP_DTMF_DIGIT]
Jan 11 17:19:01.503: act_report_digit_end 
Jan 11 17:19:01.503: vtsp_timer_stop: 31305308
Jan 11 17:19:01.503: dsp_cp_tone_off: [4/1:1:32995] packet_len=8 channel_id=3 pa
cket_id=71
Jan 11 17:19:01.503: cc_api_call_digit_end (dstVdbPtr=0x0, dstCallId=0xFFFFFFFF,
srcCallId=0x80E3,
digit=9,duration=65,xruleCallingTag=0,xruleCalledTag=0, dest_mask=0x1), digi
t_tone_mode=0
Jan 11 17:19:01.503: htsp_digit_ready: digit = 39
Jan 11 17:19:01.503: vtsp_timer: 31305308
Jan 11 17:19:01.503: htsp_process_event: [4/1:1(10), 
EM_OFFHOOK, E_VTSP_DIGIT]em_offhook_digit_collect 
Jan 11 17:19:01.503: sess_appl: ev(9=CC_EV_CALL_DIGIT_END), cid(32995), disp(0)
Jan 11 17:19:01.503: cid(32995)st(SSA_CS_MAPPING)ev(SSA_EV_CALL_DIGIT)
oldst(SSA_CS_MAPPING)cfid(-1)csize(0)in(1)fDest(0)
Jan 11 17:19:01.503: ssaDigit
Jan 11 17:19:01.503: ssaDigit, 0. sct->digit , sct->digit len 0, 
usrDigit 9, digit_tone_mode=0
Jan 11 17:19:01.503: ssaDigit,1. callinfo.called , digit 9, 
callinfo.calling , x
rulecallingtag 0, xrulecalledtag 0
Jan 11 17:19:01.503: ssaDigit, 7. callinfo.calling , sct->digit 9, result 1
Jan 11 17:19:01.603: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: 
digit=1, rtp_timestamp=0xED31C493

Jan 11 17:19:01.603: vtsp:[4/1:1:32995, S_DIGIT_COLLECT, E_DSP_DTMF_DIGIT_BEGIN]
Jan 11 17:19:01.603: act_report_digit_begin 
Jan 11 17:19:01.603: cc_api_call_digit_begin (dstVdbPtr=0x0, 
dstCallId=0xFFFFFFF
F, srcCallId=0x80E3,
digit=1, digit_begin_flags=0x1, rtp_timestamp=0xED31C493 rtp_expiration=0x0, 
dest_mask=0x1)
Jan 11 17:19:01.603: sess_appl: ev(10=CC_EV_CALL_DIGIT_BEGIN), cid(32995), 
disp(0)
Jan 11 17:19:01.603: cid(32995)st(SSA_CS_MAPPING)ev(SSA_EV_DIGIT_BEGIN)
oldst(SSA_CS_MAPPING)cfid(-1)csize(0)in(1)fDest(0)
Jan 11 17:19:01.603: ssaIgnore cid(32995), st(SSA_CS_MAPPING),oldst(0), ev(10)
Jan 11 17:19:01.643: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: 
digit=1, duration=75
Jan 11 17:19:01.643: vtsp:[4/1:1:32995, S_DIGIT_COLLECT, E_DSP_DTMF_DIGIT]
Jan 11 17:19:01.643: act_report_digit_end 
Jan 11 17:19:01.643: vtsp_timer_stop: 31305322
Jan 11 17:19:01.643: cc_api_call_digit_end (dstVdbPtr=0x0, 
dstCallId=0xFFFFFFFF,
srcCallId=0x80E3,
digit=1,duration=75,xruleCallingTag=0,xruleCalledTag=0, 
dest_mask=0x1), digit_tone_mode=0
Jan 11 17:19:01.643: htsp_digit_ready: digit = 31
Jan 11 17:19:01.643: vtsp_timer: 31305322
Jan 11 17:19:01.643: htsp_process_event: [4/1:1(10), 
EM_OFFHOOK, E_VTSP_DIGIT]em_offhook_digit_collect 
Jan 11 17:19:01.643: sess_appl: ev(9=CC_EV_CALL_DIGIT_END), cid(32995), disp(0)
Jan 11 17:19:01.643: cid(32995)st(SSA_CS_MAPPING)ev(SSA_EV_CALL_DIGIT)
oldst(SSA_CS_MAPPING)cfid(-1)csize(0)in(1)fDest(0)
Jan 11 17:19:01.643: ssaDigit
Jan 11 17:19:01.643: ssaDigit, 0. sct->digit 9, sct->digit 
len 1, usrDigit 1, digit_tone_mode=0
Jan 11 17:19:01.643: ssaDigit,1. callinfo.called , digit 91, callinfo.calling , 
xrulecallingtag 0, xrulecalledtag 0
Jan 11 17:19:01.643: ssaDigit, 7. callinfo.calling , sct->digit 91, result 1
Jan 11 17:19:01.743: vtsp_process_dsp_message: 
MSG_TX_DTMF_DIGIT_BEGIN: digit=8, rtp_timestamp=0xED31C493

Jan 11 17:19:01.743: vtsp:[4/1:1:32995, S_DIGIT_COLLECT, 
E_DSP_DTMF_DIGIT_BEGIN]
Jan 11 17:19:01.743: act_report_digit_begin 
Jan 11 17:19:01.743: cc_api_call_digit_begin (dstVdbPtr=0x0, 
dstCallId=0xFFFFFFF
F, srcCallId=0x80E3,
digit=8, digit_begin_flags=0x1, rtp_timestamp=0xED31C493
rtp_expiration=0x0, dest_mask=0x1)
Jan 11 17:19:01.743: sess_appl: ev(10=CC_EV_CALL_DIGIT_BEGIN), cid(32995), 
disp(0)
Jan 11 17:19:01.743: cid(32995)st(SSA_CS_MAPPING)ev(SSA_EV_DIGIT_BEGIN)
oldst(SSA_CS_MAPPING)cfid(-1)csize(0)in(1)fDest(0)
Jan 11 17:19:01.743: ssaIgnore cid(32995), st(SSA_CS_MAPPING),oldst(0), ev(10) 
radius_decrypt: null length 
Jan 11 17:19:01.843: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: 
digit=8, duration=75
Jan 11 17:19:01.843: vtsp:[4/1:1:32995, S_DIGIT_COLLECT, E_DSP_DTMF_DIGIT]
Jan 11 17:19:01.843: act_report_digit_end 
Jan 11 17:19:01.843: vtsp_timer_stop: 31305342
Jan 11 17:19:01.843: cc_api_call_digit_end (dstVdbPtr=0x0, dstCallId=0xFFFFFFFF,
srcCallId=0x80E3,
digit=8,duration=75,xruleCallingTag=0,xruleCalledTag=0, dest_mask=0x1), digi
t_tone_mode=0
Jan 11 17:19:01.843: htsp_digit_ready: digit = 38
Jan 11 17:19:01.843: vtsp_timer: 31305342
Jan 11 17:19:01.843: htsp_process_event: [4/1:1(10), 
EM_OFFHOOK, E_VTSP_DIGIT]em_offhook_digit_collect 
Jan 11 17:19:01.843: sess_appl: ev(9=CC_EV_CALL_DIGIT_END), cid(32995), disp(0)
Jan 11 17:19:01.843: cid(32995)st(SSA_CS_MAPPING)ev(SSA_EV_CALL_DIGIT)
oldst(SSA_CS_MAPPING)cfid(-1)csize(0)in(1)fDest(0)
Jan 11 17:19:01.843: ssaDigit
Jan 11 17:19:01.843: ssaDigit, 0. sct->digit 91, sct->digit len 2, usrDigit 8, d
igit_tone_mode=0
Jan 11 17:19:01.843: ssaDigit,1. callinfo.called , digit 918, callinfo.calling ,
xrulecallingtag 0, xrulecalledtag 0
Jan 11 17:19:01.843: ssaDigit, 7. callinfo.calling , sct->digit 918, result -1
Jan 11 17:19:01.843: ccCallDisconnect (callID=0x80E3, cause=0x1C tag=0x0)
Jan 11 17:19:01.843: vtsp:[4/1:1:32995, S_DIGIT_COLLECT, E_CC_DISCONNECT]
Jan 11 17:19:01.843: act_pre_con_disconnect 
Jan 11 17:19:01.843: vtsp_ring_noan_timer_stop: 31305342
Jan 11 17:19:01.843: dsp_cp_tone_off: [4/1:1:32995] packet_len=8 channel_id=3 pa
cket_id=71
Jan 11 17:19:01.843: dsp_voice_mode: [4/1:1:32995] cdb 62DCEA70, cdb->codec_para
ms.modem 2, inband_detect flags 0x21
Jan 11 17:19:01.843: map_dtmf_relay_type--digit relay mode: 2
Jan 11 17:19:01.843: dsp_voice_mode: [4/1:1:32995] packet_len=24 channel_id=3 pa
cket_id=73 coding_type=1 voice_field_size=160 VAD_flag=0 echo_length=256 comfort
_noise=1 inband_detect=33 digit_relay_mode=2 AGC_flag=0
Jan 11 17:19:01.843: dsp_cp_tone_on: [4/1:1:32995] packet_len=38 channel_id=3 pa
cket_id=72 tone_id=3 n_freq=2 freq_of_first=480 freq_of_second=620amp_of_first=
5206 amp_of_second=2928 direction=1 on_time_first=250 off_time_first=250 
on_time_second=0 off_time_second=0
Jan 11 17:19:01.843: vtsp_timer: 31305342
Jan 11 17:19:01.843: htsp_pre_connect_disconnect, cdb = 62DCEA70 cause = 1C

!--- Since the call is disconnected because the number received is "unassigned" !--- or "invalid" the router starts to play the reorder !--- tone and a timer, which is the wait-release !--- timeout timer, starts with default 30 seconds. !--- This call is disconnected !--- prior to the connect state.

Jan 11 17:19:01.843: htsp_process_event: [4/1:1(10), EM_OFFHOOK, 
E_HTSP_PRE_CONN_DISC]
Jan 11 17:19:31.844: vtsp_main: timer: 31308342

!--- The wait-release timer expires after 30 seconds.

Jan 11 17:19:31.844: vtsp:[4/1:1:32995, S_WAIT_RELEASE_NC, E_TIMER]

!--- The VTSP module is in a wait release state for that call. It also receives !--- event timer, which means that the timer expires so that it !--- goes into another state.

Jan 11 17:19:31.844: act_pre_con_disc_rel htsp_release_req: cause 28, no_onhook 
0
Jan 11 17:19:31.844: htsp_process_event: [4/1:1(10), EM_OFFHOOK, 
E_HTSP_RELEASE_REQ]em_offhook_release 
Jan 11 17:19:31.844: htsp_timer_stop2 em_onhook (0)[recEive and transMit4/1:1(10
)] set signal state = 0x0
Jan 11 17:19:31.844: htsp_timer_stop 
Jan 11 17:19:31.844: em_start_timer: 400 ms 
Jan 11 17:19:31.844: htsp_timer - 400 msec

!--- HTSP receives an event that requests the release of !--- the time slot and it goes into EM wait !--- onhook state. But, it cannot do anything since it says I am onhook already. !--- Also, the router starts a timer of 400 msec.

Jan 11 17:19:32.296: htsp_process_event: [4/1:1(10), EM_WAIT_ONHOOK, 
E_HTSP_EVENT_TIMER]em_wait_timeout 
Jan 11 17:19:32.296: em_stop_timers 
Jan 11 17:19:32.296: htsp_timer_stop 
Jan 11 17:19:32.296: em_start_timer: 400 ms 
Jan 11 17:19:32.296: htsp_timer - 400 msec

!--- When the 400 msec timer expires, HTSP gets into EM clear pending state. !--- It also starts another timer of 400 msec.

Jan 11 17:19:32.696: htsp_process_event: [4/1:1(10), EM_CLR_PENDING, 
E_HTSP_EVENT_TIMER]em_clr_timeout 
Jan 11 17:19:32.696: em_stop_timers 
Jan 11 17:19:32.696: htsp_timer_stop 
Jan 11 17:19:32.696: em_start_timer: 10000 ms 
Jan 11 17:19:32.696: htsp_timer - 10000 msec
Jan 11 17:19:32.700: htsp_dsp_message: SEND/RESP_SIG_STATUS: 
state=0xC timestamp=1533 systime=31308428
Jan 11 17:19:32.700: htsp_process_event: [4/1:1(10), EM_PARK, 
E_DSP_SIG_1100]em_park_offhook

!--- When the 400 msec timer expires, the router puts the time slot into !--- the EM_PARK state, and it starts another timer of 10 seconds. !--- The router still sees the ABCD=1100 from the switch.

Jan 11 17:19:42.760: htsp_process_event: [4/1:1(10), 
EM_PARK, E_HTSP_EVENT_TIMER]em_park_timerhtsp_report_onhook_sig
Jan 11 17:19:42.760: em_offhook (0)[recEive and transMit4/1:1(10)] set signal st
ate = 0x8em_onhook (1000)[recEive and transMit4/1:1(10)] set signal state = 0x0
Jan 11 17:19:42.760: htsp_timer2 - 300000 msec
Jan 11 17:19:42.760: htsp_process_event: [4/1:1(10), 
EM_PARK, E_HTSP_EVENT_TIMER]em_park_timerhtsp_report_onhook_sig
Jan 11 17:19:42.760: em_offhook (0)[recEive and transMit4/1:1(10)] 
set signal state = 0x8em_onhook (1000)[recEive and
transMit4/1:1(10)] set signal state = 0x0
Jan 11 17:19:42.760: htsp_timer2 - 300000 msec

!--- As seen from the timestamps, when the timer expires in ten seconds, !--- the router goes offhook for one second (1000 msec) and then onhook. !--- It also starts another timer of 300000 msec (5 minutes).

相关信息

• 语音技术支持
• 语音和统一通信产品支持
• Cisco IP 电话故障排除
• 技术支持和文档 - Cisco Systems