解决Catalyst 9130 AP加入问题

简介

本文档介绍在控制器加入过程中接入点停滞在Code upgrade的特定使用案例。

先决条件

要求

Cisco 建议您了解以下主题：

• Cisco WLC 9800的基础知识
• Cisco Wave2和/或11AX AP的基础知识
• 对Catalyst 9800 WLC的AP加入过程有很好的了解。

使用的组件

本文档中的信息基于以下软件和硬件版本：

• Catalyst 9800-L WLC、Cisco IOS® XE Cupertino 17.9.3
• Catalyst C9130AXI-E接入点

本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始（默认）配置。如果您的网络处于活动状态，请确保您了解所有命令的潜在影响。

拓扑

此故障排除流程适用于以本地模式连接的AP或以分支站点的flex connect模式连接的AP。

拓扑故障排除

使用案例

本文档讨论一个特定的使用案例，在该案例中，接入点完成其发现和加入阶段，但停滞于图像数据检查阶段。此问题是由于无线LAN控制器和接入点之间推送的代码升级导致出现错误消息“No space left on device”（设备无空间）。

A.接入点已完成发现阶段：

Feb 13 11:11:21 kernel: [*02/13/2024 11:11:21.4662] CAPWAP State: Discovery Feb 13 11:11:21 kernel: [*02/13/2024 11:11:21.4669] IP DNS query for CISCO-CAPWAP-CONTROLLER.cisco.com Feb 13 11:11:21 kernel: [*02/13/2024 11:11:21.5444] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0) Feb 13 11:11:21 kernel: [*02/13/2024 11:11:21.5454] Discovery Request sent to ff02::18c, discovery type UNKNOWN(0) Feb 13 11:11:21 kernel: [*02/13/2024 11:11:21.5456] Discovery Response from <WLC IP address> Feb 13 11:11:21 kernel: [*02/13/2024 11:11:21.5466] Discovery Response from <MAC of the controlloer> Feb 13 11:11:21 LED: State received is Dis_join_progress Feb 13 11:11:21 LED: LED state Changed from LED_GREEN to LED_CYCLIC_GRO_LED 

B. DTLS设置启动和加入过程完成日志：

Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.0002] CAPWAP State: DTLS Setup Feb 13 11:11:31 kernel: 
[*02/13/2024 11:11:31.6405] Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.6405] CAPWAP State: Join Feb 13 11:11:31 
kernel: [*02/13/2024 11:11:31.6422] Sending Join request to 10.228.104.4 through port 5248 Feb 13 11:11:31 kernel: 
[*02/13/2024 11:11:31.6454] Join Response from 10.228.104.4 Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.6454] 
AC accepted join request with result code: 0 Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.6489] Received wlcType 0,
 timer 30 Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.6489] TLV ID 2216 not found Feb 13 11:11:31 kernel: 
[*02/13/2024 11:11:31.6489] TLV-DEC-ERR-1: No proc for 2216  

C.完成加入过程后，接入点进入图像数据阶段。在此阶段，您可以观察从控制器到AP的映像传输，该传输失败，并出现错误消息“No space left on device”。

Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.6709] CAPWAP State: Image Data
Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.6712] AP image version 8.10.112.0 backup 0.0.0.0, Controller 17.9.3.50
Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.6712] Version does not match.
Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.7111] do PRECHECK, part1 is active part
Feb 13 11:11:31 upgrade: /tmp space: OK available 80268, required 40000 
Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.7322] upgrade.sh: /tmp space: OK available 80268, required 40000 
Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.7326] wtpImgFileReadRequest: request ap1g6a, local /tmp/part.tar
Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.7337] Image Data Request sent to 10.228.104.4, fileName [ap1g6a], slaveStatus 0
Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.7351] Image Data Response from 10.228.104.4
Feb 13 11:11:31 kernel: [*02/13/2024 11:11:31.7351] AC accepted join request with result code: 0
Feb 13 11:11:31 LED: State received is Dis_join_completed
Feb 13 11:11:31 LED: State received is Sofware_upgrade_progress
Feb 13 11:11:31 LED: LED state Changed from LED_CYCLIC_GRO_LED to LED_BLINKING_BLUE
Feb 13 11:11:45 kernel: [*02/13/2024 11:11:31.7393] <..................................................
Feb 13 11:11:53 kernel: [*02/13/2024 11:11:45.3443] ..................................................
Feb 13 11:12:07 kernel: [*02/13/2024 11:11:53.9200] ..................................................
Feb 13 11:12:16 kernel: [*02/13/2024 11:12:07.5228] ..........................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
Feb 13 11:12:25 kernel: [*02/13/2024 11:12:18.7413] ........................
Feb 13 11:12:43 kernel: [*02/13/2024 11:12:25.5137] ..................................................
Feb 13 11:13:06 kernel: [*02/13/2024 11:12:43.6235] ...................................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
Feb 13 11:13:07 kernel: [*02/13/2024 11:13:07.0982] ...Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
Feb 13 11:13:07 kernel: [*02/13/2024 11:13:07.5458] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
Feb 13 11:13:07 kernel: [*02/13/2024 11:13:07.5965] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
Feb 13 11:13:09 kernel: [*02/13/2024 11:13:07.6044] ............
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:09.9353] .............> 84387840 bytes, 62742 msgs, 1195 last
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.0817] Last block stored, IsPre 0, WriteTaskId 0
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.0847] wtpProcessImageDataRequest(10): fileName ap1g6a, pre 0
Feb 13 11:13:21 upgrade: Start doing upgrade arg1=PREDOWNLOAD arg2= arg3= ...
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.1278] do PREDOWNLOAD, part1 is active part
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.1419] upgrade.sh: Start doing upgrade arg1=PREDOWNLOAD arg2= arg3= ...
Feb 13 11:13:21 upgrade: Using image /tmp/part.tar on axel-qca ...
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.1945] upgrade.sh: Using image /tmp/part.tar on axel-qca ...
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.1947] sh: write error: No space left on device
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.1997] tar: write error: No space left on device
Feb 13 11:13:21 upgrade: ERROR: Image type mismatch. Expected:ap1g6a Got:
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.2247] upgrade.sh: ERROR: Image type mismatch. Expected:ap1g6a Got:
Feb 13 11:13:21 upgrade: Cleanup for do_upgrade...
Feb 13 11:13:21 upgrade: /tmp/upgrade_in_progress cleaned
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.2411] upgrade.sh: Cleanup for do_upgrade...
Feb 13 11:13:21 upgrade: Cleanup tmp files ...
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.2581] upgrade.sh: /tmp/upgrade_in_progress cleaned
FebFeb 13 11:13:21 kernel: [*02/13/2024 11:13:21.3072] capwap-upgrade script returned failure when calling PREDOWNLOAD.
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.3073] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.3074] CAPWAP SM handler: Failed to process message type 15 state 10.
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.3074] Failed to handle capwap control message from controller - status 2
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.3074] Failed to process encrypted capwap packet 0x55aaaa2000 from 10.228.104.4
Feb 13 11:13:21 kernel: [*02/13/2024 11:13:21.3074] Failed to send capwap message 0 to the state machine. Packet already freed.
Feb 13 11:13:22 LED: State received is Sofware_upgrade_fail
Feb 13 11:13:22 LED: LED state Changed from LED_BLINKING_BLUE to LED_GREEN
Feb 13 11:13:25 kernel: [*02/13/2024 11:13:25.6121] Invalid event 56 & state 10 combination.
Feb 13 11:13:25 kernel: [*02/13/2024 11:13:25.6121] Failed to handle timer message.
Feb 13 11:13:28 kernel: [*02/13/2024 11:13:28.4629] Re-Tx Count=1, Max Re-Tx Value=5, SendSeqNum=5, NumofPendingMsgs=1
Feb 13 11:13:28 kernel: [*02/13/2024 11:13:28.4629] 
Feb 13 11:13:31 kernel: [*02/13/2024 11:13:31.3139] Re-Tx Count=2, Max Re-Tx Value=5, SendSeqNum=5, NumofPendingMsgs=1
Feb 13 11:13:31 kernel: [*02/13/2024 11:13:31.3139] 
Feb 13 11:13:34 kernel: [*02/13/2024 11:13:34.1648] Re-Tx Count=3, Max Re-Tx Value=5, SendSeqNum=5, NumofPendingMsgs=1
Feb 13 11:13:34 kernel: [*02/13/2024 11:13:34.1648] 
Feb 13 11:13:37 kernel: [*02/13/2024 11:13:37.0157] Re-Tx Count=4, Max Re-Tx Value=5, SendSeqNum=5, NumofPendingMsgs=1
Feb 13 11:13:37 kernel: [*02/13/2024 11:13:37.0157] 
Feb 13 11:13:39 kernel: [*02/13/2024 11:13:39.8666] Re-Tx Count=5, Max Re-Tx Value=5, SendSeqNum=5, NumofPendingMsgs=1
Feb 13 11:13:39 kernel: [*02/13/2024 11:13:39.8666] 
Feb 13 11:13:42 kernel: [*02/13/2024 11:13:42.7175] Max retransmission count exceeded, going back to DISCOVER mode.
Feb 13 11:13:42 kernel: [*02/13/2024 11:13:42.7175] Dropping msg CAPWAP_ECHO_REQUEST, type = 1, len = 0, eleLen = 8, sendSeqNum = 5
Feb 13 11:13:42 kernel: [*02/13/2024 11:13:42.7185] 
Feb 13 11:13:42 kernel: [*02/13/2024 11:13:42.7185] CAPWAP State: DTLS Teardown
Feb 13 11:13:42 kernel: [*02/13/2024 11:13:42.7303] Aborting image download(0x0): Dtls cleanup, ap1g6a
Feb 13 11:13:42 kernel: [*02/13/2024 11:13:42.7952] do ABORT, part1 is active part
Feb 13 11:13:42 upgrade: Cleanup tmp files ...
Feb 13 11:13:42 kernel: [*02/13/2024 11:13:42.8145] upgrade.sh: Cleanup tmp files ...   

解决方案

有多种解决方案可以解决此问题：

第 1 项.首先，在升级到17.7+. 1之前升级到具有修复程序的中间映像。升级到17.3.5 2.继续升级到17.7+。

第 2 项.手动DE解决方法：mount -o remount，size=100M /tmp/这需要设备访问。

这两种方法都适用，使用选项2时，您可能需要与TAC的帮助。