升級Catalyst 9400 SVL設定上的CPLD
簡介
本文描述如何在Catalyst 9400 StackWise虛擬連結(SVL)設定上升級複雜可程式化邏輯裝置(CPLD)版本的分步程式。
必要條件
需求
思科建議您瞭解Catalyst 9400上的Stackwise虛擬安裝和配置的基本知識。
採用元件
本文檔中的資訊基於PID： C9404R軟體和硬體版本。
模組:
C9400-SUP-1XL
C9400-LC-24XS
軟體版本：17.09.4a
本文中的資訊是根據特定實驗室環境內的裝置所建立。文中使用到的所有裝置皆從已清除（預設）的組態來啟動。如果您的網路運作中，請確保您瞭解任何指令可能造成的影響。
拓撲
問題
在Catalyst 9400中，在某些罕見情況下升級Cisco IOS®版本時，裝置的CPLD版本未升級。特定版本的CPLD和Rommon版本可以從https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9400/software/release/17-13/release_notes/ol-17-13-9400/rommon_versions.html 連結進行檢查。
請參閱以下代碼段：
9400-1#show platform
Chassis type: C9404R
Switch 1
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
1 C9400-LC-24XS ok 00:05:00
1/0 C9400-LC-24XS ok 00:00:56
2 C9400-SUP-1XL ok 00:05:00
2/0 C9400-SUP-1XL ok 00:00:53
R0 ok, active 00:05:00
P1 C9400-PWR-3200AC ok 00:04:38
P9 C9404-FAN ok 00:04:37
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
1 20062105 17.10.1r
2 20062105 17.10.1r
Switch 2
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
1 C9400-LC-24XS ok 00:04:57
1/0 C9400-LC-24XS ok 00:00:08
2 C9400-SUP-1XL ok 00:04:57
2/0 C9400-SUP-1XL ok 00:00:07
R0 ok, standby 00:04:57
P1 C9400-PWR-3200AC ok 00:04:35
P9 C9404-FAN ok 00:04:33
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
1 19032905 17.10.1r >>>>>>>>>>CPLD did not get upgraded
2 19032905 17.10.1r >>>>>>>>>>CPLD did not get upgraded
在這種情況下，備用的CPLD在升級後沒有升級。
升級程式
步驟 1. 請使用show redundacny驗證SVL是否正常運行。
9400-1#show redundancy
Redundant System Information :
------------------------------
Available system uptime = 4 minutes
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Maintenance Mode = Disabled
Communications = Up
Current Processor Information :
-------------------------------
Active Location = Switch 1
Current Software state = ACTIVE
Uptime in current state = 4 minutes
Image Version = Cisco IOS Software [Cupertino], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 17.9.4a, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2023 by Cisco Systems, Inc.
Compiled Fri 20-Oct-23 10:44 by mcpre
BOOT = bootflash:packages.conf;
Peer Processor Information :
----------------------------
Standby Location = Switch 2 >>>>>>>>>>Switch 2 is standby
Current Software state = STANDBY HOT
Uptime in current state = 0 minutes
Image Version = Cisco IOS Software [Cupertino], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 17.9.4a, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2023 by Cisco Systems, Inc.
Compiled Fri 20-Oct-23 10:44 by mcpre
BOOT = bootflash:packages.conf;步驟 2.要升級CPLD版本，請使用以下命令：
upgrade hw-programmable cpld filename bootflash: switch {1-2} RP active9400-1#upgrade hw-programmable cpld filename bootflash: switch 2 R0
Firmware upgrade requires the SVL member to reload. Do you want to proceed?(y/n)y
Use cli 'redundancy reload peer' to upgrade the firmware on peer
9400-1#redundancy reload peer
Stack is in Half ring setup; Reloading a switch might cause stack split
Reload peer [confirm]
Preparing to reload peer步驟 3.這裡您可以看到CPLD正在升級：
Chassis 2 reloading, reason - Admin reload CLI
May 4 01:34:23.829: %PMAN-5-EXITACTION: R0/0: pvp:
Initializing Hardware......
System Bootstrap, Version 17.10.1r, RELEASE SOFTWARE (P)
Compiled Tue Aug 2 13:02:51 2022 by rel
Current ROMMON image : Primary
Last reset cause : SoftwareResetTrig
C9400-SUP-1XL platform with 16777216 Kbytes of main memory
Starting System FPGA Upgrade .....
Programming SPI Primary image is completed.
Authenticating SPI Primary image .....
IO FPGA image is authenticated successfully.
Programming Header .....
FPGA HDR file size: 12
Image page count: 1
Verifying programmed header .....
Verifying programmed header .....
Programmed header is verified successfully.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Power Cycle is needed to complete System firmware upgrade.
It takes ~7 mins to upgrade firmwre after power cycle starts.
DO NOT DISRUPT AFTER POWER C
Initializing Hardware......
Initializing Hardware......
System Bootstrap, Version 17.10.1r, RELEASE SOFTWARE (P)
Compiled Tue Aug 2 13:02:51 2022 by rel步驟 4.確認CPLD是否在待機狀態下升級：
F241.24.02-9400-1#show platform
Chassis type: C9404R
Switch 1
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
1 C9400-LC-24XS ok 00:29:38
1/0 C9400-LC-24XS ok 00:25:34
2 C9400-SUP-1XL ok 00:29:38
2/0 C9400-SUP-1XL ok 00:25:31
R0 ok, active 00:29:38
P1 C9400-PWR-3200AC ok 00:29:16
P9 C9404-FAN ok 00:29:14
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
1 20062105 17.10.1r
2 20062105 17.10.1r
Switch 2
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
1 C9400-LC-24XS ok 00:29:35
1/0 C9400-LC-24XS ok 00:00:11
2 C9400-SUP-1XL ok 00:29:35
2/0 C9400-SUP-1XL ok 00:00:10
R0 ok, standby 00:29:35
P1 C9400-PWR-3200AC ok 00:29:13
P9 C9404-FAN ok 00:29:11
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
1 20062105 17.10.1r >>>>>>>>>>CPLD got upgraded
2 20062105 17.10.1r >>>>>>>>>>CPLD got upgraded
步驟 5.在這種情況下，如果需要升級活動交換機的CPLD版本，您必須執行以下步驟：
1. Do a switchover
9400-1#redundency force-switchover >>>>>>>>>>Initially Switch 1 is active and Switch 2 is standby.
After switchover it is vise-versa
2. Upgrade the CPLD version of previous active [now standby] with the command:
9400-1#upgrade hw-programmable cpld filename bootflash: switch 1 R0
3. Reload the the standby
9400-1#redundancy reload peer
修訂記錄
| 修訂 | 發佈日期 | 意見 |
|---|---|---|
1.0 |
22-May-2024 |
初始版本 |
意見