Huawei MA5600 DSL存取多工器線路培訓組態範例
目錄
簡介
本檔案介紹華為MA5600數位使用者線路存取多工器(DSLAM)上允許超高位速率數位使用者線路(VDSL)在思科使用者端裝置(CPE)上進行培訓所需的最低組態步驟。
必要條件
需求
思科建議您在嘗試此設定之前符合以下要求：
- 電纜緊密連線在CPE的VDSL埠和DSLAM配線面板上的正確埠上
- CPE和DSLAM/線卡必須啟動並運行
採用元件
本文檔中的資訊基於充當CPE的Cisco 887VA路由器和Huwei 5600 DSLAM。但是本檔案所述內容不限於特定軟體和硬體版本。
本文中的資訊是根據特定實驗室環境內的裝置所建立。文中使用到的所有裝置皆從已清除（預設）的組態來啟動。如果您的網路正在作用，請確保您已瞭解任何指令可能造成的影響。
背景
本文檔旨在幫助工程師在背對背/實驗室環境中設定Cisco CPE和華為DSLAM，並瞭解DSL的中央辦公室(CO)端的基本配置檔案。
設定
完成以下部分以配置您的裝置：
- 線路配置檔案配置
- 通道設定檔組態
- 線路模板（線路配置檔案和通道配置檔案的組合）配置
- 將線路模板應用於連線CPE的各個DSLAM埠
線路配置檔案配置
- 檢查已建立的行配置檔案。
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 4 - 配置線路配置檔案。
MA5600#config
MA5600(config)#vdsl line-profile add 60
Failure: The profile has existed
MA5600(config)#vdsl line-profile add 61
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
> Do you want to name the profile (y/n) [n]:y
> Please input profile name:ZONE_TEST
> Transmission mode:
> 0: Custom
> 1: All (G992.1~5,T1.413,G993.2)
> 2: Full rate(G992.1/3/5,T1.413,G993.2)
> 3: G.DMT (G992.1/3/5,G993.2)
> 4: G.HS (G992.1~5,G993.2)
> 5: ADSL (G.992.1~5,T1.413)
> 6: VDSL (G993.2)
> Please select (0~6) [1]:6 >>>>>>>>>>>>>>>>>> Selecting Transmission Mode as VDSL
> Bit swap downstream 1-disable 2-enable (1~2) [2]:1
> Bit swap upstream 1-disable 2-enable (1~2) [2]:1
> Please select the form of transmit rate adaptation downstream:
> 1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
> Please select the form of transmit rate adaptation upstream:
> 1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
> Will you set SNR margin parameters? (y/n) [n]:
> Will you set DPBO parameters? (y/n)[n]:
> Will you set UPBO parameters? (y/n)[n]:
> Will you set RFI notch configuration parameter? (y/n) [n]:
> Will you set VDSL tone blackout configuration parameter? (y/n) [n]:
> Will you set mode-specific parameters? (y/n) [n]:
Add profile 61 successfully
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
61 ZONE_TEST VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 5
通道設定檔組態
- 檢查已建立的通道配置檔案。
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------
60 test_vdsl 128 100000 128 100000 Both
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 2 - 配置通道配置檔案。
MA5600(config)#vdsl channel-profile add 60
Failure: The profile has existed
MA5600(config)#vdsl channel-profile add 61
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the profile (y/n) [n]:y
> Please input profile name:ZONE_TEST
> Data path mode 1-ATM, 2-PTM, 3-Both (1~3) [3]:2 >>>>>>>>>>>>>>>>>>>>>> PTM Mode
> Will you set the minimum impulse noise protection? (y/n) [n]:
> Will you set interleaving delay parameters? (y/n) [n]:
> Will you set parameters for rate? (y/n) [n]:
> Will you set rate thresholds? (y/n) [n]:
Add profile 61 successfully
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------>
60 test_vdsl 128 100000 128 100000 Both
61 ZONE_TEST 128 100000 128 100000 PTM
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 3
線路模板配置
- 檢查已建立的行模板。
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
------------------------------------------------------------------------------
Total: 5 - 配置線路模板。
MA5600(config)#vdsl line-template add 61
Start adding template
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the template (y/n) [n]:y
> Please input template name:ZONE_TEST
> Please set the line-profile index (1~128) [1]:61 >>>>>>>>>>>>>>>>Line Profile
we added above
> Will you set channel configuration parameters? (y/n) [n]:y
> Please set the channel number (1~2) [1]:
> Channel1 configuration parameters:
> Please set the channel-profile index (1~128) [1]:61 >>>>>> Channel Profile
we added above
Add template 61 successfully
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
61 ZONE_TEST 61 61 -
------------------------------------------------------------------------------
Total: 6
將線路模板應用於DSLAM埠
在本例中，CPE連線到華為DSLAM的插槽5埠0。
MA5600(config)#display board 0
-------------------------------------------------------------------------
SlotID BoardName Status SubType0 SubType1
-------------------------------------------------------------------------
0 H563ADGE Failed
1 H565ADBF Normal >>>>>>>>>ADBF - Here 'A' means that this card supports ADSL
2 ADG Failed
3 H569SHEB Failed
4
5 H565VDBD Normal >>>> >>>>VDBD - Here 'V' means that this card supports VDSL
6
7 H561SCU Standby_normal O2FM >>>>>>>>>>>>>>>>>>>>>> Processor Cards
8 H561SCU Active_normal O2GS O2GS >>>>>>>>>>>>> Processor Cards
9
10
11 H565VDBD Failed
12 H569SHEB Failed
13
14 H561SHEA Failed
15
-------------------------------------------------------------------------
MA5600(config)#interface vdsl 0/5 (Board/ slot)
Check the port status: Status is deactivated and currently assigned to
Line Template 1 (default)
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
-----------------------------------------------------------------
0 Deactivated Disable 1 1
-----------------------------------------------------------------
將線路模板(61)分配給埠(0/5/0)
MA5600(config-if-vdsl-0/5)#activate 0 template-index 61
>>>>>>>> We are already in board 0 slot 5, hence need to activate port 0 with
Line Template 61
MA5600(config-if-vdsl-0/5)#display port state 0
---------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
---------------------------------------------------------------
0 Activating Disable 61 1 >>>>>Check the status
---------------------------------------------------------------
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
---------------------------------------------------------------
0 Activated Disable 61 1 >>Status is activated
---------------------------------------------------------------
驗證
使用本節內容，驗證您的組態。
輸出直譯器工具(僅供已註冊客戶使用)支援某些show命令。使用輸出直譯器工具來檢視show命令輸出的分析。
DSLAM驗證
檢查已建立的線路配置檔案
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
61 ZONE_TEST VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 5
檢查已建立的管道配置檔案
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------
60 test_vdsl 128 100000 128 100000 Both
61 ZONE_TEST 128 100000 128 100000 PTM
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 3
檢查已建立的行模板
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
61 ZONE_TEST 61 61 -
------------------------------------------------------------------------------
Total: 6
檢查DSLAM埠狀態
為此，您需要處於DSLAM的介面配置模式。
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
-----------------------------------------------------------------
0 Activated Disable 61 1
-----------------------------------------------------------------
驗證CPE
在CPE上輸入show controller vdsl 0命令以檢查控制器狀態。
/snip
C887VA-M#show controller vdsl 0
Controller VDSL 0 is UP
Daemon Status: Up
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0x939B
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FTX162580HZ 887VA-M 15.2(4)M
Serial Number Far:
Modem Version Near: 15.2(4)M
Modem Version Far: 0x939b
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.993.2 (VDSL2) Profile 12a
TC Mode: PTM
疑難排解
目前尚無適用於此組態的具體疑難排解資訊。
相關資訊
修訂記錄
| 修訂 | 發佈日期 | 意見 |
|---|---|---|
1.0 |
01-Dec-2014 |
初始版本 |
意見