在兩台路由器之間配置LAN到LAN IPsec隧道

下載選項

  • PDF     (462.3 KB)
    在多種裝置上使用 Adobe Reader 檢視
  • ePub     (99.7 KB)
    在 iPhone、iPad、Android、Sony Reader 或 Windows Phone 上的各種應用程式中檢視
  • Mobi (Kindle)     (108.3 KB)
    在 Kindle 裝置或多部裝置的 Kindle 應用程式上檢視
已更新: 2023 年 8 月 3 日
文件 ID:71462

無偏見用語

本產品的文件集力求使用無偏見用語。針對本文件集的目的，無偏見係定義為未根據年齡、身心障礙、性別、種族身分、民族身分、性別傾向、社會經濟地位及交織性表示歧視的用語。由於本產品軟體使用者介面中硬式編碼的語言、根據 RFP 文件使用的語言，或引用第三方產品的語言，因此本文件中可能會出現例外狀況。深入瞭解思科如何使用包容性用語。

關於此翻譯

思科已使用電腦和人工技術翻譯本文件，讓全世界的使用者能夠以自己的語言理解支援內容。請注意，即使是最佳機器翻譯，也不如專業譯者翻譯的內容準確。Cisco Systems, Inc. 對這些翻譯的準確度概不負責，並建議一律查看原始英文文件（提供連結）。

    簡介

    本檔案介紹如何在兩個Cisco路由器(Cisco IOS®或Cisco IOS® XE)之間設定透過網際網路金鑰交換(IKEv1)的原則型VPN。

    必要條件

    需求

    本文件沒有特定需求。

    採用元件

    本檔案中的資訊是根據使用Cisco IOS® 15.7版的Cisco路由器。它允許使用者透過IPSec VPN隧道跨站點訪問資源。

    本文中的資訊是根據特定實驗室環境內的裝置所建立。文中使用到的所有裝置皆從已清除（預設）的組態來啟動。如果您的網路運作中，請確保您瞭解任何指令可能造成的影響。

    慣例

    請參閱思科技術提示慣例以瞭解更多有關文件慣例的資訊。

    設定

    本節提供用於設定本文件中所述功能的資訊。

    網路圖表

    此文件使用以下網路設定：

    網路圖表

    注意：此配置中使用的IP編址方案在Internet上無法合法路由。這些地址是在實驗室環境中使用的RFC 1918 地址。

    組態

    本檔案使用下列組態：

    注意：Cisco建議對兩台裝置上的加密對映應用的ACL應該是彼此的映象。

    路由器A 
    !--- Create an ISAKMP policy for Phase 1 negotiations for the L2L tunnels.

crypto isakmp policy 10
encryption aes
hash sha256
authentication pre-share
group 14

!--- Specify the pre-shared key and the remote peer address 
    !--- to match for the L2L tunnel.

crypto isakmp key vpnuser address 10.0.0.2

!--- Create the Phase 2 policy for IPsec negotiation.

crypto ipsec transform-set myset esp-aes esp-sha256-hmac

!--- Create an ACL for the traffic to be encrypted.
!--- In this example, the traffic from 10.1.1.0/24 to 172.16.2.0/24
!--- is encrypted. The traffic which does not match the access list 
!--- is unencrypted for the Internet.

access-list 100 permit ip 10.1.1.0 0.0.0.255 172.16.2.0 0.0.0.255

!--- Create the actual crypto map. Specify an access control list (ACL),
    !--- which defines the proxy identities (local and remote host/networks).

crypto map mymap 10 ipsec-isakmp
 set peer 10.0.0.2
 set transform-set myset
 match address 100

interface GigabitEthernet0/1
ip address 10.1.1.2 255.255.255.0

!--- Apply the crypto map on the outside interface.

interface GigabitEthernet0/0
 ip address 172.16.1.1 255.255.255.0
 crypto map mymap

!--- Route to the default gateway

ip route 0.0.0.0 0.0.0.0 172.16.1.2
    路由器B 
    !--- Create an ISAKMP policy for Phase 1 negotiations for the L2L tunnels.

crypto isakmp policy 10
encryption aes
hash sha256
authentication pre-share
group 14

!--- Specify the pre-shared key and the remote peer address 
    !--- to match for the L2L tunnel.

crypto isakmp key vpnuser address 172.16.1.1

!--- Create the Phase 2 policy for IPsec negotiation.

crypto ipsec transform-set myset esp-aes esp-sha256-hmac

!--- Create an ACL for the traffic to be encrypted.
!--- In this example, the traffic from 172.16.2.0/24 to 10.1.1.0/24
!--- is encrypted. The traffic which does not match the access list 
!--- is unencrypted for the Internet.

access-list 100 permit ip 172.16.2.0 0.0.0.255 10.1.1.0 0.0.0.255

!--- Create the actual crypto map. Specify an access control list (ACL),
    !--- which defines the proxy identities (local and remote host/networks).

!
crypto map mymap 10 ipsec-isakmp
 set peer 172.16.1.1
 set transform-set myset
 match address 100

interface GigabitEthernet0/1
ip address 172.16.2.1 255.255.255.0
!

!--- Apply the crypto map on the outside interface.

interface GigabitEthernet0/0
ip address 10.0.0.2 255.255.255.0
crypto map mymap

!--- Route to the default gateway.

ip route 0.0.0.0 0.0.0.0 10.0.01

    驗證

    使用本節內容，確認您的組態是否正常運作。

    Cisco CLI Analyzer(僅供已註冊客戶使用)支援某些 show 指令。使用Cisco CLI Analyzer檢視 show 指令輸出的分析。

    • show crypto ipsec sa - 顯示當前安全關聯(SA)使用的設定、封裝和封裝數量、本地和遠端代理標識以及入站和出站安全引數索引(SPI)。

      RouterA#show crypto ipsec sa

interface: Serial2/0
    Crypto map tag: mymap, local addr 172.16.1.1

    protected vrf: (none)
   local  ident (addr/mask/prot/port): (10.1.1.0/255.255.255.0/0/0)
   remote ident (addr/mask/prot/port): (172.16.2.0/255.255.255.0/0/0)
   current_peer 10.0.0.2 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 21, #pkts encrypt: 21, #pkts digest: 21
    #pkts decaps: 21, #pkts decrypt: 21, #pkts verify: 21
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 0, #recv errors 0

     local crypto endpt.: 172.16.1.1, remote crypto endpt.: 10.0.0.2
     plaintext mtu 1438, path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/0
     current outbound spi: 0x8767D399(2271728537)
     PFS (Y/N): N, DH group: none

     inbound esp sas:
      spi: 0x6E210372(1847657330)
        transform: esp-aes esp-sha256-hmac ,
        in use settings ={Tunnel, }
        conn id: 2007, flow_id: Onboard VPN:7, sibling_flags 80004040, crypto map: mymap
        sa timing: remaining key lifetime (k/sec): (4338240/3269)
        IV size: 16 bytes
        replay detection support: Y
        Status: ACTIVE(ACTIVE)

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:
      spi: 0x8767D399(2271728537)
        transform: esp-aes esp-sha256-hmac ,
        in use settings ={Tunnel, }
        conn id: 2008, flow_id: Onboard VPN:8, sibling_flags 80004040, crypto map: mymap
        sa timing: remaining key lifetime (k/sec): (4338240/3269)
        IV size: 16 bytes
        replay detection support: Y
        Status: ACTIVE(ACTIVE)

     outbound ah sas:

     outbound pcp sas:

    • show crypto isakmp sa - 顯示所有當前IKE SA和狀態。

      RouterA#show crypto isakmp sa
dst             src             state          conn-id slot status
10.0.0.2        172.16.1.1      QM_IDLE              1    0 ACTIVE
    • show crypto map - 顯示以下對象建立的加密對映結構：
      • 加密對映的名稱和序列號。
      • 對等體地址。
      • 與本地和遠端代理標識一起應用的ACL的名稱。
      • 使用的IPsec轉換集的值。
      • 繫結加密對映的介面。
      RouterA#show crypto map
                

Crypto Map IPv4 "mymap" 10 ipsec-isakmp
                Peer = 10.0.0.2
                Extended IP access list 100
                    access-list 100 permit ip 10.1.1.0 0.0.0.255 172.16.2.0 0.0.0.255
                Current peer: 10.0.0.2
                Security association lifetime: 4608000 kilobytes/3600 seconds
                Responder-Only (Y/N): N
                PFS (Y/N): N
                Mixed-mode : Disabled
                Transform sets={
                                myset:  { esp-aes esp-sha256-hmac  } ,
                }
                Interfaces using crypto map mymap:
                                GigabitEthernet0/0

RouterB#show crypto map
                Interfaces using crypto map NiStTeSt1:

Crypto Map IPv4 "mymap" 10 ipsec-isakmp
                Peer = 172.16.1.1
                Extended IP access list 100
                    access-list 100 permit ip 172.16.2.0 0.0.0.255 10.1.1.0 0.0.0.255
                Current peer: 10.0.0.1
                Security association lifetime: 4608000 kilobytes/3600 seconds
                Responder-Only (Y/N): N
                PFS (Y/N): N
                Mixed-mode : Disabled
                Transform sets={
                                myset:  { esp-aes esp-sha256-hmac  } ,
                }
                Interfaces using crypto map mymap:
                                GigabitEthernet0/0
    • show crypto session remote <IP address of peer VPN endpoint> detail 
      RouterA#show crypto session remote 10.0.0.2 detail   
Crypto session current status

Interface: GigabitEthernet0/0
Uptime: 00:39:16 
Session status: UP-ACTIVE   >>>>> Status of the VPN 
Peer: 10.0.0.2 port 500 fvrf: (none) ivrf: (none)
      Phase1_id: 10.0.0.2
      Desc: (none)
  Session ID: 0
  IKEv1 SA: local 172.16.1.1/500 remote 10.0.0.2/500 Active
          Capabilities:(none) connid:1004 lifetime:23:20:43
  IPSEC FLOW: permit ip 10.1.1.0/255.255.255.0 172.16.2.0/255.255.255.0
        Active SAs: 2, origin: crypto map
        Inbound:  #pkts dec'ed 21 drop 0 life (KB/Sec) 4338240/1243
        Outbound: #pkts enc'ed 21 drop 0 life (KB/Sec) 4338240/1243


RouterB#show crypto session remote 172.16.1.1 detail
Crypto session current status

Interface: GigabitEthernet0/0
Uptime: 00:40:43
Session status: UP-ACTIVE    >>>>> Status of the VPN 
Peer: 172.16.1.1 port 500 fvrf: (none) ivrf: (none)
      Phase1_id: 172.16.1.1
      Desc: (none)
  Session ID: 0
  IKEv1 SA: local 10.0.0.2/500 remote 172.16.1.1/500 Active
          Capabilities:(none) connid:1004 lifetime:23:19:16
  IPSEC FLOW: permit ip 172.16.2.0/255.255.255.0 10.1.1.0/255.255.255.0
        Active SAs: 2, origin: crypto map
        Inbound:  #pkts dec'ed 21 drop 0 life (KB/Sec) 4271304/1156
        Outbound: #pkts enc'ed 21 drop 0 life (KB/Sec) 4271304/1156
      •

    疑難排解

    本節提供的資訊可用於對組態進行疑難排解。

    命令

    Cisco CLI Analyzer(僅供已註冊客戶使用)支援某些 show 指令。使用Cisco CLI Analyzer檢視 show 指令輸出的分析。

    注意：使用 debug 命令之前，請參閱有關Debug命令的重要資訊。

    • debug crypto isakmp - 顯示第1階段的ISAKMP協商。

    • debug crypto ipsec - 顯示第2階段的IPsec協商。

      •

    範例偵錯輸出

    調試輸出示例來自RouterA（發起方），用於成功進行VPN協商。

    路由器

    RouterA#debug crypto isakmp Jul 1 04:08:49.558: ISAKMP: (0):SA request profile is (NULL) Jul 1 04:08:49.558: ISAKMP: (0):Created a peer struct for 10.0.0.2, peer port 500 Jul 1 04:08:49.558: ISAKMP: (0):New peer created peer = 0x2108BC48 peer_handle = 0x80000005 Jul 1 04:08:49.558: ISAKMP: (0):Locking peer struct 0x2108BC48, refcount 1 for isakmp_initiator Jul 1 04:08:49.558: ISAKMP: (0):local port 500, remote port 500 Jul 1 04:08:49.558: ISAKMP: (0):set new node 0 to QM_IDLE Jul 1 04:08:49.558: ISAKMP: (0):Find a dup sa in the avl tree during calling isadb_insert sa = 3DA022D8 Jul 1 04:08:49.558: ISAKMP: (0):Can not start Aggressive mode,.! Success rate is 50 percent (1/2), round-trip min/avg/max = 1/1/1 ms Router# trying Main mode. Jul 1 04:08:49.558: ISAKMP: (0):found peer pre-shared key matching 10.0.0.2 Jul 1 04:08:49.558: ISAKMP: (0):constructed NAT-T vendor-rfc3947 ID Jul 1 04:08:49.558: ISAKMP: (0):constructed NAT-T vendor-07 ID Jul 1 04:08:49.558: ISAKMP: (0):constructed NAT-T vendor-03 ID Jul 1 04:08:49.558: ISAKMP: (0):constructed NAT-T vendor-02 ID Jul 1 04:08:49.558: ISAKMP: (0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM Jul 1 04:08:49.558: ISAKMP: (0):Old State = IKE_READY New State = IKE_I_MM1 Jul 1 04:08:49.562: ISAKMP: (0):beginning Main Mode exchange Jul 1 04:08:49.562: ISAKMP-PAK: (0):sending packet to 10.0.0.2 my_port 500 peer_port 500 (I) MM_NO_STATE Jul 1 04:08:49.562: ISAKMP: (0):Sending an IKE IPv4 Packet. Jul 1 04:08:49.690: ISAKMP-PAK: (0):received packet from 10.0.0.2 dport 500 sport 500 Global (I) MM_NO_STATE Jul 1 04:08:49.690: ISAKMP: (0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH Jul 1 04:08:49.690: ISAKMP: (0):Old State = IKE_I_MM1 New State = IKE_I_MM2 Jul 1 04:08:49.690: ISAKMP: (0):processing SA payload. message ID = 0 Jul 1 04:08:49.690: ISAKMP: (0):processing vendor id payload Jul 1 04:08:49.690: ISAKMP: (0):vendor ID seems Unity/DPD but major 69 mismatch Jul 1 04:08:49.690: ISAKMP: (0):vendor ID is NAT-T RFC 3947 Jul 1 04:08:49.690: ISAKMP: (0):found peer pre-shared key matching 10.0.0.2 Jul 1 04:08:49.690: ISAKMP: (0):local preshared key found Jul 1 04:08:49.690: ISAKMP: (0):Scanning profiles for xauth ... Jul 1 04:08:49.690: ISAKMP: (0):Checking ISAKMP transform 1 against priority 10 policy Jul 1 04:08:49.690: ISAKMP: (0): encryption AES-CBC Jul 1 04:08:49.690: ISAKMP: (0): keylength of 128 Jul 1 04:08:49.690: ISAKMP: (0): hash SHA256 Jul 1 04:08:49.690: ISAKMP: (0): default group 14 Jul 1 04:08:49.690: ISAKMP: (0): auth pre-share Jul 1 04:08:49.690: ISAKMP: (0): life type in seconds Jul 1 04:08:49.690: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80 Jul 1 04:08:49.690: ISAKMP: (0):atts are acceptable. Next payload is 0 Jul 1 04:08:49.690: ISAKMP: (0):Acceptable atts:actual life: 0 Jul 1 04:08:49.690: ISAKMP: (0):Acceptable atts:life: 0 Jul 1 04:08:49.690: ISAKMP: (0):Fill atts in sa vpi_length:4 Jul 1 04:08:49.690: ISAKMP: (0):Fill atts in sa life_in_seconds:86400 Jul 1 04:08:49.690: ISAKMP: (0):Returning Actual lifetime: 86400 Jul 1 04:08:49.690: ISAKMP: (0):Started lifetime timer: 86400. Jul 1 04:08:49.814: ISAKMP: (0):processing vendor id payload Jul 1 04:08:49.814: ISAKMP: (0):vendor ID seems Unity/DPD but major 69 mismatch Jul 1 04:08:49.814: ISAKMP: (0):vendor ID is NAT-T RFC 3947 Jul 1 04:08:49.814: ISAKMP: (0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE Jul 1 04:08:49.814: ISAKMP: (0):Old State = IKE_I_MM2 New State = IKE_I_MM2 Jul 1 04:08:49.818: ISAKMP-PAK: (0):sending packet to 10.0.0.2 my_port 500 peer_port 500 (I) MM_SA_SETUP Jul 1 04:08:49.818: ISAKMP: (0):Sending an IKE IPv4 Packet. Jul 1 04:08:49.818: ISAKMP: (0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE Jul 1 04:08:49.818: ISAKMP: (0):Old State = IKE_I_MM2 New State = IKE_I_MM3 Jul 1 04:08:49.978: ISAKMP-PAK: (0):received packet from 10.0.0.2 dport 500 sport 500 Global (I) MM_SA_SETUP Jul 1 04:08:49.978: ISAKMP: (0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH Jul 1 04:08:49.978: ISAKMP: (0):Old State = IKE_I_MM3 New State = IKE_I_MM4 Jul 1 04:08:49.978: ISAKMP: (0):processing KE payload. message ID = 0 Jul 1 04:08:50.138: ISAKMP: (0):processing NONCE payload. message ID = 0 Jul 1 04:08:50.138: ISAKMP: (0):found peer pre-shared key matching 10.0.0.2 Jul 1 04:08:50.138: ISAKMP: (1004):processing vendor id payload Jul 1 04:08:50.138: ISAKMP: (1004):vendor ID is Unity Jul 1 04:08:50.138: ISAKMP: (1004):processing vendor id payload Jul 1 04:08:50.138: ISAKMP: (1004):vendor ID is DPD Jul 1 04:08:50.138: ISAKMP: (1004):processing vendor id payload Jul 1 04:08:50.138: ISAKMP: (1004):speaking to another IOS box! Jul 1 04:08:50.138: ISAKMP: (1004):received payload type 20 Jul 1 04:08:50.138: ISAKMP: (1004):His hash no match - this node outside NAT Jul 1 04:08:50.138: ISAKMP: (1004):received payload type 20 Jul 1 04:08:50.138: ISAKMP: (1004):No NAT Found for self or peer Jul 1 04:08:50.138: ISAKMP: (1004):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE Jul 1 04:08:50.138: ISAKMP: (1004):Old State = IKE_I_MM4 New State = IKE_I_MM4 Jul 1 04:08:50.138: ISAKMP: (1004):Send initial contact Jul 1 04:08:50.138: ISAKMP: (1004):SA is doing Jul 1 04:08:50.138: ISAKMP: (1004):pre-shared key authentication using id type ID_IPV4_ADDR Jul 1 04:08:50.138: ISAKMP: (1004):ID payload next-payload : 8 type : 1 Jul 1 04:08:50.138: ISAKMP: (1004): address : 172.16.1.1 >>>>> IKE ID sent Jul 1 04:08:50.138: ISAKMP: (1004): protocol : 17 port : 500 length : 12 Jul 1 04:08:50.138: ISAKMP: (1004):Total payload length: 12 Jul 1 04:08:50.138: ISAKMP-PAK: (1004):sending packet to 10.0.0.2 my_port 500 peer_port 500 (I) MM_KEY_EXCH Jul 1 04:08:50.138: ISAKMP: (1004):Sending an IKE IPv4 Packet. Jul 1 04:08:50.138: ISAKMP: (1004):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE Jul 1 04:08:50.138: ISAKMP: (1004):Old State = IKE_I_MM4 New State = IKE_I_MM5 Jul 1 04:08:50.138: ISAKMP-PAK: (1004):received packet from 10.0.0.2 dport 500 sport 500 Global (I) MM_KEY_EXCH Jul 1 04:08:50.142: ISAKMP: (1004):processing ID payload. message ID = 0 Jul 1 04:08:50.142: ISAKMP: (1004):ID payload next-payload : 8 type : 1 Jul 1 04:08:50.142: ISAKMP: (1004): address : 10.0.0.2 >>>>> IKE ID received Jul 1 04:08:50.142: ISAKMP: (1004): protocol : 17 port : 500 length : 12 Jul 1 04:08:50.142: ISAKMP: (0):peer matches *none* of the profiles Jul 1 04:08:50.142: ISAKMP: (1004):processing HASH payload. message ID = 0 Jul 1 04:08:50.142: ISAKMP: (1004):SA authentication status: authenticated Jul 1 04:08:50.142: ISAKMP: (1004):SA has been authenticated with 10.0.0.2 Jul 1 04:08:50.142: ISAKMP: (0):Trying to insert a peer 172.16.1.1/10.0.0.2/500/, Jul 1 04:08:50.142: ISAKMP: (0): and inserted successfully 2108BC48. Jul 1 04:08:50.142: ISAKMP: (1004):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH Jul 1 04:08:50.142: ISAKMP: (1004):Old State = IKE_I_MM5 New State = IKE_I_MM6 Jul 1 04:08:50.142: ISAKMP: (1004):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE Jul 1 04:08:50.142: ISAKMP: (1004):Old State = IKE_I_MM6 New State = IKE_I_MM6 Jul 1 04:08:50.142: ISAKMP: (1004):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE Jul 1 04:08:50.142: ISAKMP: (1004):Old State = IKE_I_MM6 New State = IKE_P1_COMPLETE Jul 1 04:08:50.142: ISAKMP: (1004):beginning Quick Mode exchange, M-ID of 3184909968 Jul 1 04:08:50.142: ISAKMP: (1004):QM Initiator gets spi Jul 1 04:08:50.142: ISAKMP-PAK: (1004):sending packet to 10.0.0.2 my_port 500 peer_port 500 (I) QM_IDLE Jul 1 04:08:50.142: ISAKMP: (1004):Sending an IKE IPv4 Packet. Jul 1 04:08:50.142: ISAKMP: (1004):Node 3184909968, Input = IKE_MESG_INTERNAL, IKE_INIT_QM Jul 1 04:08:50.142: ISAKMP: (1004):Old State = IKE_QM_READY New State = IKE_QM_I_QM1 Jul 1 04:08:50.142: ISAKMP: (1004):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE >>>>> Phase1 negotiation is complete Jul 1 04:08:50.142: ISAKMP: (1004):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE Jul 1 04:08:50.146: ISAKMP-PAK: (1004):received packet from 10.0.0.2 dport 500 sport 500 Global (I) QM_IDLE Jul 1 04:08:50.146: ISAKMP: (1004):processing HASH payload. message ID = 3184909968 Jul 1 04:08:50.146: ISAKMP: (1004):processing SA payload. message ID = 3184909968 Jul 1 04:08:50.146: ISAKMP: (1004):Checking IPSec proposal 1 Jul 1 04:08:50.146: ISAKMP: (1004):transform 1, ESP_AES Jul 1 04:08:50.146: ISAKMP: (1004): attributes in transform: Jul 1 04:08:50.146: ISAKMP: (1004): encaps is 1 (Tunnel) Jul 1 04:08:50.146: ISAKMP: (1004): SA life type in seconds Jul 1 04:08:50.146: ISAKMP: (1004): SA life duration (basic) of 3600 Jul 1 04:08:50.146: ISAKMP: (1004): SA life type in kilobytes Jul 1 04:08:50.146: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0 Jul 1 04:08:50.146: ISAKMP: (1004): authenticator is HMAC-SHA256 Jul 1 04:08:50.146: ISAKMP: (1004): key length is 128 Jul 1 04:08:50.146: ISAKMP: (1004):atts are acceptable. Jul 1 04:08:50.146: IPSEC(validate_proposal_request): proposal part #1 Jul 1 04:08:50.146: IPSEC(validate_proposal_request): proposal part #1, (key eng. msg.) INBOUND local= 172.16.1.1:0, remote= 10.0.0.2:0, local_proxy= 10.1.1.0/255.255.255.0/256/0, remote_proxy= 172.16.2.0/255.255.255.0/256/0, protocol= ESP, transform= esp-aes esp-sha256-hmac (Tunnel), lifedur= 0s and 0kb, spi= 0x0(0), conn_id= 0, keysize= 128, flags= 0x0 Jul 1 04:08:50.146: Crypto mapdb : proxy_match src addr : 10.1.1.0 dst addr : 172.16.2.0 protocol : 0 src port : 0 dst port : 0 Jul 1 04:08:50.146: (ipsec_process_proposal)Map Accepted: mymap, 10 Jul 1 04:08:50.146: ISAKMP: (1004):processing NONCE payload. message ID = 3184909968 Jul 1 04:08:50.146: ISAKMP: (1004):processing ID payload. message ID = 3184909968 Jul 1 04:08:50.146: ISAKMP: (1004):processing ID payload. message ID = 3184909968 Jul 1 04:08:50.146: ISAKMP: (1004):Node 3184909968, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH Jul 1 04:08:50.146: ISAKMP: (1004):Old State = IKE_QM_I_QM1 New State = IKE_QM_IPSEC_INSTALL_AWAIT Jul 1 04:08:50.146: IPSEC(key_engine): got a queue event with 1 KMI message(s) Jul 1 04:08:50.146: Crypto mapdb : proxy_match src addr : 10.1.1.0 dst addr : 172.16.2.0 protocol : 256 src port : 0 dst port : 0 Jul 1 04:08:50.146: IPSEC(crypto_ipsec_create_ipsec_sas): Map found mymap, 10 Jul 1 04:08:50.146: IPSEC(crypto_ipsec_sa_find_ident_head): reconnecting with the same proxies and peer 10.0.0.2 Jul 1 04:08:50.146: IPSEC(get_old_outbound_sa_for_peer): No outbound SA found for peer 22C55798 Jul 1 04:08:50.146: IPSEC(create_sa): sa created, (sa) sa_dest= 172.16.1.1, sa_proto= 50, sa_spi= 0x6E210372(1847657330), >>>>> Inbound SPI  sa_trans= esp-aes esp-sha256-hmac , sa_conn_id= 2007 sa_lifetime(k/sec)= (4608000/3600), (identity) local= 172.16.1.1:0, remote= 10.0.0.2:0, local_proxy= 10.1.1.0/255.255.255.0/256/0, remote_proxy= 172.16.2.0/255.255.255.0/256/0 Jul 1 04:08:50.146: IPSEC(create_sa): sa created, (sa) sa_dest= 10.0.0.2, sa_proto= 50, sa_spi= 0x8767D399(2271728537), >>>>> Outbound SPI sa_trans= esp-aes esp-sha256-hmac , sa_conn_id= 2008 sa_lifetime(k/sec)= (4608000/3600), (identity) local= 172.16.1.1:0, remote= 10.0.0.2:0, local_proxy= 10.1.1.0/255.255.255.0/256/0, remote_proxy= 172.16.2.0/255.255.255.0/256/0 Jul 1 04:08:50.150: IPSEC: Expand action denied, notify RP Jul 1 04:08:50.150: ISAKMP-ERROR: (0):Failed to find peer index node to update peer_info_list Jul 1 04:08:50.150: ISAKMP: (1004):Received IPSec Install callback... proceeding with the negotiation Jul 1 04:08:50.150: ISAKMP: (1004):Successfully installed IPSEC SA (SPI:0x6E210372) on GigabitEthernet0/0 >>>>> IPsec SA is installed Jul 1 04:08:50.150: ISAKMP-PAK: (1004):sending packet to 10.0.0.2 my_port 500 peer_port 500 (I) QM_IDLE Jul 1 04:08:50.150: ISAKMP: (1004):Sending an IKE IPv4 Packet. Jul 1 04:08:50.150: ISAKMP: (1004):deleting node -1110057328 error FALSE reason "No Error" Jul 1 04:08:50.150: ISAKMP: (1004):Node 3184909968, Input = IKE_MESG_FROM_IPSEC, IPSEC_INSTALL_DONE Jul 1 04:08:50.150: ISAKMP: (1004):Old State = IKE_QM_IPSEC_INSTALL_AWAIT New State = IKE_QM_PHASE2_COMPLETE >>>>> Phase2 negotiation is complete Jul 1 04:08:50.950: ISAKMP: (1003):purging node -262896492 Jul 1 04:09:09.710: ISAKMP: (1003):purging SA., sa=3DA05D84, delme=3DA05D84

    相關資訊

    修訂記錄

    修訂 發佈日期 意見
    3.0
    03-Aug-2023
    更新了簡介、SEO、品牌要求、樣式要求和格式。
    2.0
    05-Jul-2022
    已將文檔更新為Cisco IOS版本15.7
    1.0
    12-Sep-2006
    初始版本
    TAC Authored

    由思科工程師貢獻

    • Mrutunjay Sethi
      Cisco TAC Engineer

    這份文件是否有所幫助？

    Feedback意見

    讓思科協助您

    本文件適用於這些產品