透過PAT傳遞LAN到LAN IPSec隧道的IOS路由器配置示例

下載選項

  • PDF     (438.5 KB)
    在多種裝置上使用 Adobe Reader 檢視
已更新: 2008 年 1 月 14 日
文件 ID:23820

無偏見用語

本產品的文件集力求使用無偏見用語。針對本文件集的目的，無偏見係定義為未根據年齡、身心障礙、性別、種族身分、民族身分、性別傾向、社會經濟地位及交織性表示歧視的用語。由於本產品軟體使用者介面中硬式編碼的語言、根據 RFP 文件使用的語言，或引用第三方產品的語言，因此本文件中可能會出現例外狀況。深入瞭解思科如何使用包容性用語。

關於此翻譯

思科已使用電腦和人工技術翻譯本文件，讓全世界的使用者能夠以自己的語言理解支援內容。請注意，即使是最佳機器翻譯，也不如專業譯者翻譯的內容準確。Cisco Systems, Inc. 對這些翻譯的準確度概不負責，並建議一律查看原始英文文件（提供連結）。

簡介

本文檔提供埠地址轉換(PAT)的示例配置，以允許建立LAN到LAN IPSec隧道。它適用於只有一個公有IP地址(在Cisco IOS®路由器中使用以對所有流量執行PAT)並且需要透過IPSec隧道的場景。

對於運行早於12.2(13)T的Cisco IOS軟體版本的VPN網關，執行PAT的路由器上需要IPSec直通功能，以允許透過封裝安全有效載荷(ESP)。

注意：此功能在軟體建議中稱為透過網路地址轉換(NAT)的IPSec支援(僅限註冊客戶)。

要從本地(PATed)對等體啟動隧道，不需要進行配置。要從遠端對等體啟動隧道，需要使用以下命令：

  • ip nat inside source static esp inside_ip interface interface

  • ip nat inside source static udp inside_ip 500 interface interface 500

對於運行高於12.2(13)T的Cisco IOS軟體版本的VPN網關，IPSec流量被封裝到使用者資料協定(UDP)埠4500資料包中。此功能稱為IPSec NAT透明模式。要從本地(PATed)對等體啟動隧道，不需要進行配置。

要從遠端對等體啟動隧道，需要使用以下命令：

  • ip nat inside source static udp inside_ip 4500 interface interface 4500

  • ip nat inside source static udp inside_ip 500 interface interface 500

發出no crypto ipsec nat-transparency udp-encaps命令可停用IPSec NAT透明模式。

必要條件

需求

本文件沒有特定需求。

採用元件

本檔案中的資訊是根據Cisco IOS軟體版本12.3(7)T1。

本文中的資訊是根據特定實驗室環境內的裝置所建立。文中使用到的所有裝置皆從已清除（預設）的組態來啟動。如果您的網路正在作用，請確保您已瞭解任何指令可能造成的影響。

慣例

如需文件慣例的詳細資訊，請參閱思科技術提示慣例。

設定

本節提供用於設定本文件中所述功能的資訊。

網路圖表

此文件使用以下網路設定：

ios_pat_ipsec_tunnel.gif

使用IPSec NAT透明配置

本檔案使用下列組態：

VPN-Gateway1 
VPN-Gateway1#show running-config 
Building configuration...

Current configuration : 1017 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname VPN-Gateway1
!


!--- VPN Gateway1 and VPN Gateway2 can be any devices that !--- perform IPSec. For detailed information on configuring IPSec !--- refer to IPSec Technology Support Information. !--- IPSec configuration between VPN Gateway1 and VPN Gateway2 !--- is beyond the scope of this document. 


boot-start-marker
boot-end-marker
!
!
clock timezone EST 0
no aaa new-model
ip subnet-zero
!
!
ip audit po max-events 100
no ftp-server write-enable
!
!
!         
! 
!

!--- IKE policies (phase 1).

crypto isakmp policy 10
 authentication pre-share
crypto isakmp key cisco123 address 209.165.201.2
!
!
crypto ipsec transform-set basic esp-des esp-md5-hmac 
!

!--- IPSec policies (phase 1).

crypto map mymap 10 ipsec-isakmp 
 set peer 209.165.201.2
 set transform-set basic 
 match address 101
!
!
!
interface Ethernet0/0
 ip address 192.168.1.1 255.255.255.0
!
interface Serial1/0
 ip address 209.165.200.2 255.255.255.252
 serial restart-delay 0
 crypto map mymap
!
ip classless
ip route 0.0.0.0 0.0.0.0 209.165.200.1
no ip http server
no ip http secure-server
!
!
!
access-list 101 permit ip 192.168.1.0 0.0.0.255 172.16.2.0 0.0.0.255
access-list 101 remark Crypto ACL
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
!
!
end

PAT路由器 
PAT-Router#show running-config 
Building configuration...

Current configuration : 971 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname PAT-Router
!
boot-start-marker
boot-end-marker
!
!
clock timezone EST 0
no aaa new-model
ip subnet-zero
!
!
ip audit po max-events 100
no ftp-server write-enable
!
!
!         
! 
no crypto isakmp enable
!
!
!
interface Ethernet0/0
 ip address 172.16.1.1 255.255.255.0

!--- This declares the interface as inside for NAT purposes.

 ip nat inside
!
interface Serial1/0
 ip address 209.165.201.2 255.255.255.224

!--- This declares the interface as !--- outside for NAT purposes.

 ip nat outside
 serial restart-delay 0
!
ip classless
ip route 0.0.0.0 0.0.0.0 209.165.201.1
ip route 172.16.0.0 255.255.0.0 172.16.1.2
no ip http server
no ip http secure-server
!
ip nat inside source list 1 interface Serial1/0 overload

!--- This allows PAT to be used for regular Internet traffic. 

ip nat inside source static udp 172.16.1.2 4500 interface Serial1/0 4500

!--- This permits IPSec traffic destined for the Serial1/0 !--- interface to be sent to the inside IP address 172.16.1.2.

ip nat inside source static udp 172.16.1.2 500 interface Serial1/0 500

!--- This allows UDP traffic for the Serial1/0 interface to be !--- statically mapped to the inside IP address 172.16.1.2. !--- This is required for the Internet Security Association !--- and Key Management Protocol (ISAKMP) negotiation to be !--- initiated from VPN-Gateway1 to VPN-Gateway2.

!
!
access-list 1 permit 172.16.0.0 0.0.255.255
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
!
!
end

VPN-Gateway2 
VPN-Gateway2#show running-config
Building configuration...

Current configuration : 986 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname VPN-Gateway2
!


!--- VPN Gateway1 and VPN Gateway2 can be any devices !--- that perform IPSec. For detailed information on !--- IPSec configuration refer to IPSec Technology Support Information. !--- IPSec configuration between VPN Gateway1 and VPN Gateway2 !--- is beyond the scope of this document. 


boot-start-marker
boot-end-marker
!
!
clock timezone EST 0
no aaa new-model
ip subnet-zero
!
!
ip audit po max-events 100
no ftp-server write-enable
!
!
!         
! 
!

!--- IKE policies (phase 1).

crypto isakmp policy 10
 authentication pre-share
crypto isakmp key cisco123 address 209.165.200.2
!
!
crypto ipsec transform-set basic esp-des esp-md5-hmac 
!

!--- IPSec policies (phase 1).

crypto map mymap 10 ipsec-isakmp 
 set peer 209.165.200.2
 set transform-set basic 
 match address 101
!
!
!
interface Ethernet0/0
 ip address 172.16.1.2 255.255.255.0
 crypto map mymap
!
interface Ethernet1/0
 ip address 172.16.2.1 255.255.255.0
!         
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.1.1
no ip http server
no ip http secure-server
!
!
!
access-list 101 permit ip 172.16.2.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 101 remark Crypto ACL
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
!
!
end

沒有IPSec NAT透明度的配置

VPN-Gateway1 
VPN-Gateway1#show running-config 
Building configuration...

Current configuration : 1017 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname VPN-Gateway1
!


!--- VPN Gateway1 and VPN Gateway2 can be any devices !--- that perform IPSec. For detailed information on !--- IPSec configuration refer to IPSec Technology Support Information. !--- IPSec configuration between VPN Gateway1 and VPN Gateway2 !--- is beyond the scope of this document. 


boot-start-marker
boot-end-marker
!
!
clock timezone EST 0
no aaa new-model
ip subnet-zero
!
!
ip audit po max-events 100
no ftp-server write-enable
!
!
!         
! 
!

!--- IKE policies (phase 1).

crypto isakmp policy 10
 authentication pre-share
crypto isakmp key cisco123 address 209.165.201.2
!
!
crypto ipsec transform-set basic esp-des esp-md5-hmac 
!

!--- IPSec policies (phase 1).

crypto map mymap 10 ipsec-isakmp 
 set peer 209.165.201.2
 set transform-set basic 
 match address 101
!
!
!
interface Ethernet0/0
 ip address 192.168.1.1 255.255.255.0
!
interface Serial1/0
 ip address 209.165.200.2 255.255.255.252
 serial restart-delay 0
 crypto map mymap
!
ip classless
ip route 0.0.0.0 0.0.0.0 209.165.200.1
no ip http server
no ip http secure-server
!
!
!
access-list 101 permit ip 192.168.1.0 0.0.0.255 172.16.2.0 0.0.0.255
access-list 101 remark Crypto ACL
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
!
!
end

PAT路由器 
PAT-Router#show running-config 
Building configuration...

Current configuration : 971 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname PAT-Router
!
boot-start-marker
boot-end-marker
!
!
clock timezone EST 0
no aaa new-model
ip subnet-zero
!
!
ip audit po max-events 100
no ftp-server write-enable
!
!
!         
! 
no crypto isakmp enable
!
!
!
interface Ethernet0/0
 ip address 172.16.1.1 255.255.255.0

!--- This declares the interface as inside for NAT purposes.

 ip nat inside
!
interface Serial1/0
 ip address 209.165.201.2 255.255.255.224

!--- This declares the interface as !--- outside for NAT purposes.

 ip nat outside
 serial restart-delay 0
!
ip classless
ip route 0.0.0.0 0.0.0.0 209.165.201.1
ip route 172.16.0.0 255.255.0.0 172.16.1.2
no ip http server
no ip http secure-server
!
ip nat inside source list 1 interface Serial1/0 overload

!--- This allows PAT to be used for regular Internet traffic.
 
ip nat inside source static esp 172.16.1.2 interface Serial1/0

!--- This permits the IPSec ESP tunnel mode !--- destined for the Serial1/0 interface to be sent !--- to the inside IP address 172.16.1.2. The "esp" !--- option allows a single ESP tunnel-mode !--- VPN setup to be possible.

ip nat inside source static udp 172.16.1.2 500 interface Serial1/0 500

!--- This allows UDP traffic for the Serial1/0 !--- interface to be statically mapped to the inside !--- IP address 172.16.1.2. This is required !--- for the ISAKMP negotiation to be initiated !--- from VPN-Gateway1 to VPN-Gateway2.

!
!
access-list 1 permit 172.16.0.0 0.0.255.255
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
!
!
end

VPN-Gateway2 
VPN-Gateway2#show running-config
Building configuration...

Current configuration : 986 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname VPN-Gateway2
!


!--- VPN Gateway1 and VPN Gateway2 can be any devices !--- that perform IPSec. For detailed information on !--- IPSec configuration refer to IPSec Technology Support Information. !--- IPSec configuration between VPN Gateway1 and VPN Gateway2 !--- is beyond the scope of this document. 


boot-start-marker
boot-end-marker
!
!
clock timezone EST 0
no aaa new-model
ip subnet-zero
!
!
ip audit po max-events 100
no ftp-server write-enable
!
!
!         
! 
!

!--- IKE policies (phase 1).

crypto isakmp policy 10
 authentication pre-share
crypto isakmp key cisco123 address 209.165.200.2
!
!
crypto ipsec transform-set basic esp-des esp-md5-hmac
no crypto ipsec nat-transparency udp-encaps 
!

!--- IPSec policies (phase 1).

crypto map mymap 10 ipsec-isakmp 
 set peer 209.165.200.2
 set transform-set basic 
 match address 101
!
!
!
interface Ethernet0/0
 ip address 172.16.1.2 255.255.255.0
 crypto map mymap
!
interface Ethernet1/0
 ip address 172.16.2.1 255.255.255.0
!         
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.1.1
no ip http server
no ip http secure-server
!
!
!
access-list 101 permit ip 172.16.2.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 101 remark Crypto ACL
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
!
!
end

驗證

以下各節提供可用來確認組態是否正常運作的資訊。

輸出直譯器工具支援某些show命令(僅供註冊客戶使用)，透過該工具可檢視對show命令輸出的分析。

使用IPSec NAT透明模式進行驗證

  • show crypto isakmp sa -顯示對等體上的所有當前Internet Key Exchange (IKE)安全關聯(SA)。 

    VPN-Gateway1#show crypto isakmp sa
dst             src             state          conn-id slot
209.165.200.2   209.165.201.2   QM_IDLE              1    0


VPN-Gateway2#show crypto isakmp sa
dst             src             state          conn-id slot
209.165.200.2   172.16.1.2      QM_IDLE              1    0

  • show crypto ipsec sa -顯示對等體之間構建的IPSec SA。 

    VPN-Gateway1#show crypto ipsec sa

 
!--- This command is issued after a ping !--- is attempted from PC2 to PC1.


interface: Serial1/0
    Crypto map tag: mymap, local addr. 209.165.200.2

   protected vrf: 
   local  ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
   remote ident (addr/mask/prot/port): (172.16.2.0/255.255.255.0/0/0)
   current_peer: 209.165.201.2:4500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 6, #pkts encrypt: 6, #pkts digest: 6
    #pkts decaps: 6, #pkts decrypt: 6, #pkts verify: 6
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 0, #recv errors 0

     local crypto endpt.: 209.165.200.2, remote crypto endpt.: 209.165.201.2
     path mtu 1500, media mtu 1500
     current outbound spi: 9CCA0619

     inbound esp sas:
      spi: 0x4E6B990F(1315674383)
        transform: esp-des esp-md5-hmac ,
        in use settings ={Tunnel UDP-Encaps, }
        slot: 0, conn id: 2000, flow_id: 5, crypto map: mymap
        crypto engine type: Software, engine_id: 1
        sa timing: remaining key lifetime (k/sec): (4602622/3489)
        ike_cookies: 8973C578 9C7DEB45 5C9BE6DC 7F737D09
        IV size: 8 bytes
        replay detection support: Y

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:
      spi: 0x9CCA0619(2630485529)
        transform: esp-des esp-md5-hmac ,
        in use settings ={Tunnel UDP-Encaps, }
        slot: 0, conn id: 2001, flow_id: 6, crypto map: mymap
        crypto engine type: Software, engine_id: 1
        sa timing: remaining key lifetime (k/sec): (4602622/3489)
        ike_cookies: 8973C578 9C7DEB45 5C9BE6DC 7F737D09
        IV size: 8 bytes
        replay detection support: Y

     outbound ah sas:

     outbound pcp sas:


VPN-Gateway2#show crypto ipsec sa

 
!--- This command is issued after a ping !--- is attempted from PC2 to PC1.


interface: Ethernet0/0
    Crypto map tag: mymap, local addr. 172.16.1.2

   protected vrf: 
   local  ident (addr/mask/prot/port): (172.16.2.0/255.255.255.0/0/0)
   remote ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
   current_peer: 209.165.200.2:4500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 23, #pkts encrypt: 23, #pkts digest: 23
    #pkts decaps: 16, #pkts decrypt: 16, #pkts verify: 16
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 7, #recv errors 0

     local crypto endpt.: 172.16.1.2, remote crypto endpt.: 209.165.200.2
     path mtu 1500, media mtu 1500
     current outbound spi: 4E6B990F

     inbound esp sas:
      spi: 0x9CCA0619(2630485529)
        transform: esp-des esp-md5-hmac ,
        in use settings ={Tunnel UDP-Encaps, }
        slot: 0, conn id: 2000, flow_id: 1, crypto map: mymap
        crypto engine type: Software, engine_id: 1
        sa timing: remaining key lifetime (k/sec): (4384024/3481)
        ike_cookies: 5C9BE6DC 7F737D09 8973C578 9C7DEB45
        IV size: 8 bytes
        replay detection support: Y

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:
      spi: 0x4E6B990F(1315674383)
        transform: esp-des esp-md5-hmac ,
        in use settings ={Tunnel UDP-Encaps, }
        slot: 0, conn id: 2001, flow_id: 2, crypto map: mymap
        crypto engine type: Software, engine_id: 1
        sa timing: remaining key lifetime (k/sec): (4384024/3481)
        ike_cookies: 5C9BE6DC 7F737D09 8973C578 9C7DEB45
        IV size: 8 bytes
        replay detection support: Y

     outbound ah sas:

     outbound pcp sas:

  • show ip nat translations -顯示處於活動狀態的NAT轉換。

    PAT-Router#show ip nat translations
Pro Inside global      Inside local       Outside local      Outside global
udp 209.165.201.2:500  172.16.1.2:500     ---                ---
udp 209.165.201.2:4500 172.16.1.2:4500    ---                ---

驗證IPSec NAT不透明

  • show crypto isakmp sa -顯示對等體上的所有當前IKE SA。 

    VPN-Gateway1#show crypto isakmp sa
dst             src             state          conn-id slot
209.165.200.2   209.165.201.2   QM_IDLE              1    0


VPN-Gateway2#show crypto isakmp sa
dst             src             state          conn-id slot
209.165.200.2   172.16.1.2      QM_IDLE              1    0

  • show crypto ipsec sa -顯示對等體之間構建的IPSec SA。 

    VPN-Gateway1#show crypto ipsec sa

 
!--- This command is issued after a ping !--- is attempted from PC2 to PC1.


interface: Serial1/0
    Crypto map tag: mymap, local addr. 209.165.200.2

   protected vrf: 
   local  ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
   remote ident (addr/mask/prot/port): (172.16.2.0/255.255.255.0/0/0)
   current_peer: 209.165.201.2:500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 21, #pkts encrypt: 21, #pkts digest: 21
    #pkts decaps: 15, #pkts decrypt: 15, #pkts verify: 15
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 4, #recv errors 0

     local crypto endpt.: 209.165.200.2, remote crypto endpt.: 209.165.201.2
     path mtu 1500, media mtu 1500
     current outbound spi: E89A0245

     inbound esp sas:
      spi: 0xB5F867BC(3052955580)
        transform: esp-des esp-md5-hmac ,
        in use settings ={Tunnel, }
        slot: 0, conn id: 2000, flow_id: 7, crypto map: mymap
        crypto engine type: Software, engine_id: 1
        sa timing: remaining key lifetime (k/sec): (4538665/3553)
        ike_cookies: 8973C578 DD91CB42 5C9BE6DC 63813771
        IV size: 8 bytes
        replay detection support: Y

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:
      spi: 0xE89A0245(3902407237)
        transform: esp-des esp-md5-hmac ,
        in use settings ={Tunnel, }
        slot: 0, conn id: 2001, flow_id: 8, crypto map: mymap
        crypto engine type: Software, engine_id: 1
        sa timing: remaining key lifetime (k/sec): (4538665/3553)
        ike_cookies: 8973C578 DD91CB42 5C9BE6DC 63813771
        IV size: 8 bytes
        replay detection support: Y

     outbound ah sas:

     outbound pcp sas:


VPN-Gateway2#show crypto ipsec sa

 
!--- This command is issued after a ping !--- is attempted from PC2 to PC1.


interface: Ethernet0/0
    Crypto map tag: mymap, local addr. 172.16.1.2

   protected vrf: 
   local  ident (addr/mask/prot/port): (172.16.2.0/255.255.255.0/0/0)
   remote ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
   current_peer: 209.165.200.2:500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 5, #pkts encrypt: 5, #pkts digest: 5
    #pkts decaps: 5, #pkts decrypt: 5, #pkts verify: 5
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 1, #recv errors 0

     local crypto endpt.: 172.16.1.2, remote crypto endpt.: 209.165.200.2
     path mtu 1500, media mtu 1500
     current outbound spi: B5F867BC

     inbound esp sas:
      spi: 0xE89A0245(3902407237)
        transform: esp-des esp-md5-hmac ,
        in use settings ={Tunnel, }
        slot: 0, conn id: 2000, flow_id: 3, crypto map: mymap
        crypto engine type: Software, engine_id: 1
        sa timing: remaining key lifetime (k/sec): (4572084/3561)
        ike_cookies: 5C9BE6DC 63813771 8973C578 DD91CB42
        IV size: 8 bytes
        replay detection support: Y

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:
      spi: 0xB5F867BC(3052955580)
        transform: esp-des esp-md5-hmac ,
        in use settings ={Tunnel, }
        slot: 0, conn id: 2001, flow_id: 4, crypto map: mymap
        crypto engine type: Software, engine_id: 1
        sa timing: remaining key lifetime (k/sec): (4572084/3561)
        ike_cookies: 5C9BE6DC 63813771 8973C578 DD91CB42
        IV size: 8 bytes
        replay detection support: Y

     outbound ah sas:

     outbound pcp sas:

  • show ip nat translations -顯示處於活動狀態的NAT轉換。

    PAT-Router#show ip nat translations
Pro Inside global      Inside local       Outside local      Outside global
udp 209.165.201.2:500  172.16.1.2:500     ---                ---
esp 209.165.201.2:0    172.16.1.2:0       ---                ---

疑難排解

本節提供的資訊可用於對組態進行疑難排解。

如果設定包含PAT的LAN-to-LAN IPSec隧道（如本文檔所述）但仍然遇到問題，請收集來自每個裝置的debug輸出和show命令的輸出，以供Cisco技術支援人員進行分析。

以下是與此組態相關的疑難排解資訊。有關故障排除的其他資訊，請參閱IP安全故障排除-瞭解和使用debug命令和驗證NAT操作和基本NAT故障排除。

以下幾部分顯示debug命令和輸出示例。

注意：在發出debug命令之前，請參閱有關Debug命令的重要資訊。

使用IPSec NAT透明模式進行故障排除

  • debug crypto ipsec -顯示第2階段的IPSec協商。

  • debug crypto isakmp -顯示第1階段的ISAKMP協商。

  • debug ip nat detail -檢查路由器所執行的NAT。

以下是命令輸出示例。

VPN-Gateway1#debug crypto ipsec
Crypto IPSEC debugging is on
VPN-Gateway1#debug crypto isakmp
Crypto ISAKMP debugging is on
VPN-Gateway1#show debug
Cryptographic Subsystem:
  Crypto ISAKMP debugging is on
  Crypto IPSEC debugging is on

 
!--- These debugs appeared after a ping !--- was attempted from PC2 to PC1.


*Jun 27 09:31:36.159: ISAKMP (0:0): received packet from 209.165.201.2 
                                    dport 500 sport 500 Global (N) NEW SA
*Jun 27 09:31:36.159: ISAKMP: Created a peer struct for 209.165.201.2, 
                              peer port 500
*Jun 27 09:31:36.159: ISAKMP: Locking peer struct 0x2C50610, IKE refcount 
                              1 for crypto_isakmp_process_block
*Jun 27 09:31:36.159: ISAKMP: local port 500, remote port 500
*Jun 27 09:31:36.559: insert sa successfully sa = 290B720
*Jun 27 09:31:36.559: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, 
                                        IKE_MM_EXCH
*Jun 27 09:31:36.559: ISAKMP:(0:1:SW:1):Old State = IKE_READY  
                                        New State = IKE_R_MM1 

*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): processing SA payload. message ID = 0
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): vendor ID seems Unity/DPD but 
                                         major 157 mismatch
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): vendor ID is NAT-T v3
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): vendor ID seems Unity/DPD but major 
                                         123 mismatch
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): vendor ID is NAT-T v2
*Jun 27 09:31:36.619: ISAKMP: Looking for a matching key for 209.165.201.2 
                              in default : success
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1):found peer pre-shared key matching 
                                        209.165.201.2
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): local preshared key found
*Jun 27 09:31:36.619: ISAKMP : Scanning profiles for xauth ...
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1):Checking ISAKMP transform 1 against 
                                       priority 10 policy
*Jun 27 09:31:36.619: ISAKMP:      encryption DES-CBC
*Jun 27 09:31:36.619: ISAKMP:      hash SHA
*Jun 27 09:31:36.619: ISAKMP:      default group 1
*Jun 27 09:31:36.619: ISAKMP:      auth pre-share
*Jun 27 09:31:36.619: ISAKMP:      life type in seconds
*Jun 27 09:31:36.619: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80 
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1):atts are acceptable. Next payload is 0
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): vendor ID seems Unity/DPD but major 
                                         157 mismatch
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): vendor ID is NAT-T v3
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): vendor ID seems Unity/DPD but 
                                         major 123 mismatch
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1): vendor ID is NAT-T v2
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                                        IKE_PROCESS_MAIN_MODE
*Jun 27 09:31:36.619: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM1  
                                        New State = IKE_R_MM1 

*Jun 27 09:31:36.771: ISAKMP:(0:1:SW:1): constructed NAT-T vendor-03 ID
*Jun 27 09:31:36.771: ISAKMP:(0:1:SW:1): sending packet to 209.165.201.2 
                                         my_port 500 peer_port 500 (R) MM_SA_SETUP
*Jun 27 09:31:36.771: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                                        IKE_PROCESS_COMPLETE
*Jun 27 09:31:36.771: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM1  
                                        New State = IKE_R_MM2 

*Jun 27 09:31:37.179: ISAKMP (0:134217729): received packet from 
                                            209.165.201.2 dport 500 sport 500 
                                            Global (R) MM_SA_SETUP
*Jun 27 09:31:37.179: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
*Jun 27 09:31:37.179: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM2  New State = IKE_R_MM3 

*Jun 27 09:31:38.199: ISAKMP:(0:1:SW:1): processing KE payload. 
                                         message ID = 0
*Jun 27 09:31:38.199: ISAKMP:(0:1:SW:1): processing NONCE payload. message ID = 0
*Jun 27 09:31:38.759: ISAKMP: Looking for a matching key for 209.165.201.2 
                              in default : success
*Jun 27 09:31:38.759: ISAKMP:(0:1:SW:1):found peer pre-shared key matching 
                                         209.165.201.2
*Jun 27 09:31:38.759: ISAKMP:(0:1:SW:1):SKEYID state generated
*Jun 27 09:31:38.759: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:38.759: ISAKMP:(0:1:SW:1): vendor ID is Unity
*Jun 27 09:31:38.759: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:38.759: ISAKMP:(0:1:SW:1): vendor ID is DPD
*Jun 27 09:31:38.759: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:38.759: ISAKMP:(0:1:SW:1): speaking to another IOS box!
*Jun 27 09:31:38.759: ISAKMP:received payload type 17
*Jun 27 09:31:38.759: ISAKMP:received payload type 17
*Jun 27 09:31:38.759: ISAKMP (0:134217729): NAT found, the node outside NAT
*Jun 27 09:31:38.759: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                                IKE_PROCESS_MAIN_MODE
*Jun 27 09:31:38.759: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM3  
                             New State = IKE_R_MM3 

*Jun 27 09:31:38.891: ISAKMP:(0:1:SW:1): sending packet to 209.165.201.2 
                               my_port 500 peer_port 500 (R) MM_KEY_EXCH
*Jun 27 09:31:38.891: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                               IKE_PROCESS_COMPLETE
*Jun 27 09:31:38.891: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM3  
                              New State = IKE_R_MM4 

*Jun 27 09:31:40.071: ISAKMP (0:134217729): received packet from 
                             209.165.201.2 dport 4500 sport 4500 Global 
                            (R) MM_KEY_EXCH
*Jun 27 09:31:40.071: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, 
                             IKE_MM_EXCH
*Jun 27 09:31:40.071: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM4  
                              New State = IKE_R_MM5 

*Jun 27 09:31:40.199: ISAKMP:(0:1:SW:1): processing ID payload. message ID = 0
*Jun 27 09:31:40.199: ISAKMP (0:134217729): ID payload 
        next-payload : 8
        type         : 1 
        address      : 172.16.1.2 
        protocol     : 17 
        port         : 0 
        length       : 12
*Jun 27 09:31:40.199: ISAKMP:(0:1:SW:1):: peer matches *none* of the profiles
*Jun 27 09:31:40.199: ISAKMP:(0:1:SW:1): processing HASH payload. message ID = 0
*Jun 27 09:31:40.199: ISAKMP:(0:1:SW:1): processing NOTIFY INITIAL_CONTACT 
                             protocol 1
        spi 0, message ID = 0, sa = 290B720
*Jun 27 09:31:40.199: ISAKMP:(0:1:SW:1):SA authentication status:
        authenticated
*Jun 27 09:31:40.199: ISAKMP:(0:1:SW:1): Process initial contact,
                          bring down existing phase 1 and 2 SA's with 
                         local 209.165.200.2 
                         remote 209.165.201.2 remote port 4500
*Jun 27 09:31:40.231: IPSEC(key_engine): got a queue event with 1 kei messages
*Jun 27 09:31:40.399: ISAKMP:(0:1:SW:1):SA authentication status:
        authenticated
*Jun 27 09:31:40.399: ISAKMP:(0:1:SW:1):SA has been authenticated 
                             with 209.165.201.2
*Jun 27 09:31:40.399: ISAKMP:(0:1:SW:1):Detected port floating to 
                             port = 4500
*Jun 27 09:31:40.399: ISAKMP: Trying to insert a peer 
                            209.165.200.2/209.165.201.2/4500/,  
                             and inserted successfully.
*Jun 27 09:31:40.399: ISAKMP:(0:1:SW:1):: peer matches *none* of the profiles
*Jun 27 09:31:40.399: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                       IKE_PROCESS_MAIN_MODE
*Jun 27 09:31:40.399: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM5  
                        New State = IKE_R_MM5 

*Jun 27 09:31:40.459: ISAKMP:(0:1:SW:1):SA is doing pre-shared key 
                       authentication using id type ID_IPV4_ADDR
*Jun 27 09:31:40.459: ISAKMP (0:134217729): ID payload 
        next-payload : 8
        type         : 1 
        address      : 209.165.200.2 
        protocol     : 17 
        port         : 0 
        length       : 12
*Jun 27 09:31:40.459: ISAKMP:(0:1:SW:1):Total payload length: 12
*Jun 27 09:31:40.459: ISAKMP:(0:1:SW:1): sending packet to 209.165.201.2 
                      my_port 4500 peer_port 4500 (R) MM_KEY_EXCH
*Jun 27 09:31:40.459: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                       IKE_PROCESS_COMPLETE
*Jun 27 09:31:40.459: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM5  
                      New State = IKE_P1_COMPLETE 

*Jun 27 09:31:40.539: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PHASE1_COMPLETE
*Jun 27 09:31:40.539: ISAKMP:(0:1:SW:1):Old State = IKE_P1_COMPLETE  
                      New State = IKE_P1_COMPLETE 

*Jun 27 09:31:40.999: ISAKMP (0:134217729): received packet from 209.165.201.2 
                      dport 4500 sport 4500 Global (R) QM_IDLE      
*Jun 27 09:31:40.999: ISAKMP: set new node 1546295295 to QM_IDLE      
*Jun 27 09:31:40.999: ISAKMP:(0:1:SW:1): processing HASH payload. message 
                      ID = 1546295295
*Jun 27 09:31:40.999: ISAKMP:(0:1:SW:1): processing SA payload. 
                       message ID = 1546295295
*Jun 27 09:31:40.999: ISAKMP:(0:1:SW:1):Checking IPSec proposal 1
*Jun 27 09:31:40.999: ISAKMP: transform 1, ESP_DES
*Jun 27 09:31:40.999: ISAKMP:   attributes in transform:
*Jun 27 09:31:40.999: ISAKMP:      encaps is 61443 (Tunnel-UDP)
*Jun 27 09:31:40.999: ISAKMP:      SA life type in seconds
*Jun 27 09:31:40.999: ISAKMP:      SA life duration (basic) of 3600
*Jun 27 09:31:40.999: ISAKMP:      SA life type in kilobytes
*Jun 27 09:31:40.999: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0 
*Jun 27 09:31:40.999: ISAKMP:      authenticator is HMAC-MD5
*Jun 27 09:31:40.999: ISAKMP:(0:1:SW:1):atts are acceptable.
*Jun 27 09:31:40.999: IPSEC(validate_proposal_request): proposal part #1,
  (key eng. msg.) INBOUND local= 209.165.200.2, remote= 209.165.201.2, 
    local_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel-UDP), 
    lifedur= 0s and 0kb, 
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x400
*Jun 27 09:31:40.999: IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf = 
*Jun 27 09:31:40.999: ISAKMP:(0:1:SW:1): processing NONCE payload. 
                      message ID = 1546295295
*Jun 27 09:31:40.999: ISAKMP:(0:1:SW:1): processing ID payload. 
                       message ID = 1546295295
*Jun 27 09:31:40.999: ISAKMP:(0:1:SW:1): processing ID payload. 
                      message ID = 1546295295
*Jun 27 09:31:40.999: ISAKMP:(0:1:SW:1): asking for 1 spis from ipsec
*Jun 27 09:31:40.999: ISAKMP:(0:1:SW:1):Node 1546295295, Input = 
                      IKE_MESG_FROM_PEER, IKE_QM_EXCH
*Jun 27 09:31:40.999: ISAKMP:(0:1:SW:1):Old State = IKE_QM_READY  
                       New State = IKE_QM_SPI_STARVE
*Jun 27 09:31:41.031: IPSEC(key_engine): got a queue event with 1 kei messages
*Jun 27 09:31:41.031: IPSEC(spi_response): getting spi 1315674383 for SA 
        from 209.165.200.2   to 209.165.201.2   for prot 3
*Jun 27 09:31:41.079: ISAKMP: received ike message (2/1)
*Jun 27 09:31:42.039: ISAKMP:(0:1:SW:1): sending packet to 209.165.201.2 
                       my_port 4500 peer_port 4500 (R) QM_IDLE      
*Jun 27 09:31:42.039: ISAKMP:(0:1:SW:1):Node 1546295295, 
                      Input = IKE_MESG_FROM_IPSEC, IKE_SPI_REPLY
*Jun 27 09:31:42.039: ISAKMP:(0:1:SW:1):Old State = IKE_QM_SPI_STARVE  
                       New State = IKE_QM_R_QM2
*Jun 27 09:31:42.311: ISAKMP (0:134217729): received packet from 209.165.201.2 
                       dport 4500 sport 4500 Global (R) QM_IDLE      
*Jun 27 09:31:42.311: IPSec: Flow_switching Allocated flow for flow_id 134217733 
*Jun 27 09:31:42.311: IPSec: Flow_switching Allocated flow for flow_id 134217734 
*Jun 27 09:31:43.339: %CRYPTO-5-SESSION_STATUS: Crypto tunnel is UP  .  
                      Peer 209.165.201.2:4500       Id: 172.16.1.2
*Jun 27 09:31:43.339: ISAKMP: Locking peer struct 0x2C50610, IPSEC refcount 1 
                      for for stuff_ke
*Jun 27 09:31:43.339: ISAKMP:(0:1:SW:1): Creating IPSec SAs
*Jun 27 09:31:43.339:         inbound SA from 209.165.201.2 to 209.165.200.2 
                              (f/i)  0/ 0
        (proxy 172.16.2.0 to 192.168.1.0)
*Jun 27 09:31:43.339:         has spi 0x4E6B990F and conn_id 2000 and flags 400
*Jun 27 09:31:43.339:         lifetime of 3600 seconds
*Jun 27 09:31:43.339:         lifetime of 4608000 kilobytes
*Jun 27 09:31:43.339:         has client flags 0x10
*Jun 27 09:31:43.339:         outbound SA from 209.165.200.2 to 209.165.201.2 
                              (f/i) 0/0
        (proxy 192.168.1.0 to 172.16.2.0)
*Jun 27 09:31:43.339:         has spi -1664481767 and conn_id 2001 and flags 408
*Jun 27 09:31:43.339:         lifetime of 3600 seconds
*Jun 27 09:31:43.339:         lifetime of 4608000 kilobytes
*Jun 27 09:31:43.339:         has client flags 0x10
*Jun 27 09:31:43.339: ISAKMP:(0:1:SW:1):deleting node 1546295295 error 
                      FALSE reason "quick mode done (await)"
*Jun 27 09:31:43.339: ISAKMP:(0:1:SW:1):Node 1546295295, Input = 
                      IKE_MESG_FROM_PEER, IKE_QM_EXCH
*Jun 27 09:31:43.339: ISAKMP:(0:1:SW:1):Old State = IKE_QM_R_QM2  
                       New State = IKE_QM_PHASE2_COMPLETE
*Jun 27 09:31:43.359: IPSEC(key_engine): got a queue event with 2 kei messages
*Jun 27 09:31:43.359: IPSEC(initialize_sas): ,
  (key eng. msg.) INBOUND local= 209.165.200.2, remote= 209.165.201.2, 
    local_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel-UDP), 
    lifedur= 3600s and 4608000kb, 
    spi= 0x4E6B990F(1315674383), conn_id= 134219728, keysize= 0, flags= 0x400
*Jun 27 09:31:43.359: IPSEC(initialize_sas): ,
  (key eng. msg.) OUTBOUND local= 209.165.200.2, remote= 209.165.201.2, 
    local_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel-UDP), 
    lifedur= 3600s and 4608000kb, 
    spi= 0x9CCA0619(2630485529), conn_id= 134219729, keysize= 0, flags= 0x408
*Jun 27 09:31:43.359: IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf = 
*Jun 27 09:31:43.359: IPSEC(crypto_ipsec_sa_find_ident_head): 
                      reconnecting with the same proxies and 209.165.201.2
*Jun 27 09:31:43.359: IPSEC(mtree_add_ident): src 192.168.1.0, dest 172.16.2.0, 
                      dest_port 0

*Jun 27 09:31:43.359: IPSEC(create_sa): sa created,
  (sa) sa_dest= 209.165.200.2, sa_prot= 50, 
    sa_spi= 0x4E6B990F(1315674383), 
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 134219728
*Jun 27 09:31:43.359: IPSEC(create_sa): sa created,
  (sa) sa_dest= 209.165.201.2, sa_prot= 50, 
    sa_spi= 0x9CCA0619(2630485529), 
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 134219729
*Jun 27 09:32:33.359: ISAKMP:(0:1:SW:1):purging node 1546295295 

VPN-Gateway2#debug crypto ipsec
Crypto IPSEC debugging is on
VPN-Gateway2#debug crypto isakmp
Crypto ISAKMP debugging is on
VPN-Gateway2#show debug
Cryptographic Subsystem:
  Crypto ISAKMP debugging is on
  Crypto IPSEC debugging is on
VPN-Gateway2#


 !--- These debugs appeared after a ping !--- was attempted from PC2 to PC1.


*Jun 27 09:31:35.447: IPSEC(sa_request): ,
  (key eng. msg.) OUTBOUND local= 172.16.1.2, remote= 209.165.200.2, 
    local_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel), 
    lifedur= 3600s and 4608000kb, 
    spi= 0x9CCA0619(2630485529), conn_id= 0, keysize= 0, flags= 0x400A
*Jun 27 09:31:35.455: ISAKMP: received ke message (1/1)
*Jun 27 09:31:35.455: ISAKMP:(0:0:N/A:0): SA request profile is (NULL)
*Jun 27 09:31:35.455: ISAKMP: Created a peer struct for 209.165.200.2, 
                      peer port 500
*Jun 27 09:31:35.455: ISAKMP: Locking peer struct 0x2C42438, IKE refcount 
                       1 for isakmp_initiator
*Jun 27 09:31:35.455: ISAKMP: local port 500, remote port 500
*Jun 27 09:31:35.487: ISAKMP: set new node 0 to QM_IDLE      
*Jun 27 09:31:35.487: insert sa successfully sa = 2CB1E80
*Jun 27 09:31:35.487: ISAKMP:(0:1:SW:1):Can not start Aggressive mode, 
                      trying Main mode.
*Jun 27 09:31:35.487: ISAKMP: Looking for a matching key for 209.165.200.2 
                      in default : success
*Jun 27 09:31:35.487: ISAKMP:(0:1:SW:1):found peer pre-shared key matching 
                      209.165.200.2
*Jun 27 09:31:35.487: ISAKMP:(0:1:SW:1): constructed NAT-T vendor-03 ID
*Jun 27 09:31:35.487: ISAKMP:(0:1:SW:1): constructed NAT-T vendor-02 ID
*Jun 27 09:31:35.487: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_IPSEC, 
                      IKE_SA_REQ_MM
*Jun 27 09:31:35.487: ISAKMP:(0:1:SW:1):Old State = IKE_READY  
                       New State = IKE_I_MM1 

*Jun 27 09:31:35.487: ISAKMP:(0:1:SW:1): beginning Main Mode exchange
*Jun 27 09:31:35.487: ISAKMP:(0:1:SW:1): sending packet to 209.165.200.2 
                      my_port 500 peer_port 500 (I) MM_NO_STATE
*Jun 27 09:31:36.607: ISAKMP (0:134217729): received packet from 209.165.200.2 
                      dport 500 sport 500 Global (I) MM_NO_STATE
*Jun 27 09:31:36.607: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, 
                      IKE_MM_EXCH
*Jun 27 09:31:36.607: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM1  
                      New State = IKE_I_MM2 

*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1): processing SA payload. message ID = 0
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1): vendor ID seems Unity/DPD but 
                      major 157 mismatch
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1): vendor ID is NAT-T v3
*Jun 27 09:31:36.687: ISAKMP: Looking for a matching key for 209.165.200.2 
                      in default : success
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1):found peer pre-shared key 
                      matching 209.165.200.2
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1): local preshared key found
*Jun 27 09:31:36.687: ISAKMP : Scanning profiles for xauth ...
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1):Checking ISAKMP transform 1 
                      against priority 10 policy
*Jun 27 09:31:36.687: ISAKMP:      encryption DES-CBC
*Jun 27 09:31:36.687: ISAKMP:      hash SHA
*Jun 27 09:31:36.687: ISAKMP:      default group 1
*Jun 27 09:31:36.687: ISAKMP:      auth pre-share
*Jun 27 09:31:36.687: ISAKMP:      life type in seconds
*Jun 27 09:31:36.687: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80 
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1):atts are acceptable. Next payload is 0
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1): vendor ID seems Unity/DPD but 
                      major 157 mismatch
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1): vendor ID is NAT-T v3
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_MAIN_MODE
*Jun 27 09:31:36.687: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM2  
                      New State = IKE_I_MM2 

*Jun 27 09:31:36.795: ISAKMP:(0:1:SW:1): sending packet to 209.165.200.2 
                      my_port 500 peer_port 500 (I) MM_SA_SETUP
*Jun 27 09:31:36.795: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_COMPLETE
*Jun 27 09:31:36.795: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM2  
                       New State = IKE_I_MM3 

*Jun 27 09:31:38.727: ISAKMP (0:134217729): received packet from 209.165.200.2 
                      dport 500 sport 500 Global (I) MM_SA_SETUP
*Jun 27 09:31:38.727: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, 
                      IKE_MM_EXCH
*Jun 27 09:31:38.727: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM3  
                       New State = IKE_I_MM4 

*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1): processing KE payload. 
                       message ID = 0
*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1): processing NONCE payload. message ID = 0
*Jun 27 09:31:38.807: ISAKMP: Looking for a matching key for 209.165.200.2 
                      in default : success
*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1):found peer pre-shared key matching 
                      209.165.200.2
*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1):SKEYID state generated
*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1): vendor ID is Unity
*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1): vendor ID is DPD
*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1): speaking to another IOS box!
*Jun 27 09:31:38.807: ISAKMP:received payload type 17
*Jun 27 09:31:38.807: ISAKMP (0:134217729): NAT found, the node inside NAT
*Jun 27 09:31:38.807: ISAKMP:received payload type 17
*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_MAIN_MODE
*Jun 27 09:31:38.807: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM4  
                      New State = IKE_I_MM4 

*Jun 27 09:31:38.935: ISAKMP:(0:1:SW:1):Send initial contact
*Jun 27 09:31:38.935: ISAKMP:(0:1:SW:1):SA is doing pre-shared key 
                      authentication using id type ID_IPV4_ADDR
*Jun 27 09:31:38.935: ISAKMP (0:134217729): ID payload 
        next-payload : 8
        type         : 1 
        address      : 172.16.1.2 
        protocol     : 17 
        port         : 0 
        length       : 12
*Jun 27 09:31:38.935: ISAKMP:(0:1:SW:1):Total payload length: 12
*Jun 27 09:31:38.935: ISAKMP:(0:1:SW:1): sending packet to 209.165.200.2 
                      my_port 4500 peer_port 4500 (I) MM_KEY_EXCH
*Jun 27 09:31:38.935: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_COMPLETE
*Jun 27 09:31:38.935: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM4  
                       New State = IKE_I_MM5 

*Jun 27 09:31:40.307: ISAKMP (0:134217729): received packet from 
                      209.165.200.2 dport 4500 sport 4500 Global (I) MM_KEY_EXCH
*Jun 27 09:31:40.307: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, 
                       IKE_MM_EXCH
*Jun 27 09:31:40.307: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM5  
                      New State = IKE_I_MM6 

*Jun 27 09:31:40.367: ISAKMP:(0:1:SW:1): processing ID payload. message ID = 0
*Jun 27 09:31:40.367: ISAKMP (0:134217729): ID payload 
        next-payload : 8
        type         : 1 
        address      : 209.165.200.2 
        protocol     : 17 
        port         : 0 
        length       : 12
*Jun 27 09:31:40.367: ISAKMP:(0:1:SW:1): processing HASH payload. message ID = 0
*Jun 27 09:31:40.367: ISAKMP:(0:1:SW:1):SA authentication status:
        authenticated
*Jun 27 09:31:40.367: ISAKMP:(0:1:SW:1):SA has been authenticated with 
                      209.165.200.2
*Jun 27 09:31:40.367: ISAKMP:(0:1:SW:1):: peer matches *none* of the 
                       profiles
*Jun 27 09:31:40.367: ISAKMP:(0:1:SW:1):Setting UDP ENC peer struct 
                      0x2940710 sa= 0x2CB1E80
*Jun 27 09:31:40.367: ISAKMP: Trying to insert a peer 
                      172.16.1.2/209.165.200.2/4500/,  and inserted successfully.
*Jun 27 09:31:40.367: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_MAIN_MODE
*Jun 27 09:31:40.367: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM6  
                       New State = IKE_I_MM6 

*Jun 27 09:31:40.367: ISAKMP: sending nat keepalive packet to 209.165.200.2(4500)
*Jun 27 09:31:40.395: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                       IKE_PROCESS_COMPLETE
*Jun 27 09:31:40.395: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM6  
                      New State = IKE_P1_COMPLETE 

*Jun 27 09:31:40.475: ISAKMP:(0:1:SW:1):beginning Quick Mode exchange, 
                      M-ID of 1546295295
*Jun 27 09:31:40.507: ISAKMP:(0:1:SW:1): sending packet to 209.165.200.2 
                       my_port 4500 peer_port 4500 (I) QM_IDLE      
*Jun 27 09:31:40.507: ISAKMP:(0:1:SW:1):Node 1546295295, Input = IKE_MESG_INTERNAL, 
                      IKE_INIT_QM
*Jun 27 09:31:40.507: ISAKMP:(0:1:SW:1):Old State = IKE_QM_READY  
                      New State = IKE_QM_I_QM1
*Jun 27 09:31:40.507: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PHASE1_COMPLETE
*Jun 27 09:31:40.507: ISAKMP:(0:1:SW:1):Old State = IKE_P1_COMPLETE  
                      New State = IKE_P1_COMPLETE 

*Jun 27 09:31:41.887: ISAKMP (0:134217729): received packet from 
                       209.165.200.2 dport 4500 sport 4500 Global (I) QM_IDLE      
*Jun 27 09:31:41.887: ISAKMP:(0:1:SW:1): processing HASH payload. 
                       message ID = 1546295295
*Jun 27 09:31:41.887: ISAKMP:(0:1:SW:1): processing SA payload. 
                       message ID = 1546295295
*Jun 27 09:31:41.887: ISAKMP:(0:1:SW:1):Checking IPSec proposal 1
*Jun 27 09:31:41.887: ISAKMP: transform 1, ESP_DES
*Jun 27 09:31:41.887: ISAKMP:   attributes in transform:
*Jun 27 09:31:41.887: ISAKMP:      encaps is 61443 (Tunnel-UDP)
*Jun 27 09:31:41.887: ISAKMP:      SA life type in seconds
*Jun 27 09:31:41.887: ISAKMP:      SA life duration (basic) of 3600
*Jun 27 09:31:41.887: ISAKMP:      SA life type in kilobytes
*Jun 27 09:31:41.887: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0 
*Jun 27 09:31:41.887: ISAKMP:      authenticator is HMAC-MD5
*Jun 27 09:31:41.887: ISAKMP:(0:1:SW:1):atts are acceptable.
*Jun 27 09:31:41.887: IPSEC(validate_proposal_request): proposal part #1,
  (key eng. msg.) INBOUND local= 172.16.1.2, remote= 209.165.200.2, 
    local_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel-UDP), 
    lifedur= 0s and 0kb, 
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x400
*Jun 27 09:31:41.887: IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf = 
*Jun 27 09:31:41.887: ISAKMP:(0:1:SW:1): processing NONCE payload. 
                       message ID = 1546295295
*Jun 27 09:31:41.887: ISAKMP:(0:1:SW:1): processing ID payload. 
                       message ID = 1546295295
*Jun 27 09:31:41.887: ISAKMP:(0:1:SW:1): processing ID payload. 
                       message ID = 1546295295
*Jun 27 09:31:41.887: IPSec: Flow_switching Allocated flow for flow_id 134217729 
*Jun 27 09:31:41.887: IPSec: Flow_switching Allocated flow for flow_id 134217730 
*Jun 27 09:31:41.947: %CRYPTO-5-SESSION_STATUS: Crypto tunnel is UP  .  
                      Peer 209.165.200.2:4500       Id: 209.165.200.2
*Jun 27 09:31:41.947: ISAKMP: Locking peer struct 0x2C42438, IPSEC refcount 
                      1 for for stuff_ke
*Jun 27 09:31:41.947: ISAKMP:(0:1:SW:1): Creating IPSec SAs
*Jun 27 09:31:41.947:         inbound SA from 209.165.200.2 to 172.16.1.2 
                               (f/i)  0/ 0
        (proxy 192.168.1.0 to 172.16.2.0)
*Jun 27 09:31:41.947:         has spi 0x9CCA0619 and conn_id 2000 and flags 400
*Jun 27 09:31:41.947:         lifetime of 3600 seconds
*Jun 27 09:31:41.947:         lifetime of 4608000 kilobytes
*Jun 27 09:31:41.947:         has client flags 0x10
*Jun 27 09:31:41.947:         outbound SA from 172.16.1.2 to 209.165.200.2 
                              (f/i) 0/0
        (proxy 172.16.2.0 to 192.168.1.0)
*Jun 27 09:31:41.947:         has spi 1315674383 and conn_id 2001 and flags 408
*Jun 27 09:31:41.947:         lifetime of 3600 seconds
*Jun 27 09:31:41.947:         lifetime of 4608000 kilobytes
*Jun 27 09:31:41.947:         has client flags 0x10
*Jun 27 09:31:41.947: ISAKMP:(0:1:SW:1): sending packet to 209.165.200.2 
                         my_port 4500 peer_port 4500 (I) QM_IDLE      
*Jun 27 09:31:41.947: ISAKMP:(0:1:SW:1):deleting node 1546295295 error 
                      FALSE reason ""
*Jun 27 09:31:41.947: ISAKMP:(0:1:SW:1):Node 1546295295, Input = 
                      IKE_MESG_FROM_PEER, IKE_QM_EXCH
*Jun 27 09:31:41.947: ISAKMP:(0:1:SW:1):Old State = IKE_QM_I_QM1  
                       New State = IKE_QM_PHASE2_COMPLETE
*Jun 27 09:31:41.955: IPSEC(key_engine): got a queue event with 2 kei messages
*Jun 27 09:31:41.955: IPSEC(initialize_sas): ,
  (key eng. msg.) INBOUND local= 172.16.1.2, remote= 209.165.200.2, 
    local_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel-UDP), 
    lifedur= 3600s and 4608000kb, 
    spi= 0x9CCA0619(2630485529), conn_id= 134219728, keysize= 0, flags= 0x400
*Jun 27 09:31:41.955: IPSEC(initialize_sas): ,
  (key eng. msg.) OUTBOUND local= 172.16.1.2, remote= 209.165.200.2, 
    local_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel-UDP), 
    lifedur= 3600s and 4608000kb, 
    spi= 0x4E6B990F(1315674383), conn_id= 134219729, keysize= 0, flags= 0x408
*Jun 27 09:31:41.955: IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf = 
*Jun 27 09:31:41.955: IPSEC(crypto_ipsec_sa_find_ident_head): reconnecting 
                     with the same proxies and 209.165.200.2
*Jun 27 09:31:41.955: IPSEC(mtree_add_ident): src 172.16.2.0, dest 192.168.1.0, 
                       dest_port 0

*Jun 27 09:31:41.955: IPSEC(create_sa): sa created,
  (sa) sa_dest= 172.16.1.2, sa_prot= 50, 
    sa_spi= 0x9CCA0619(2630485529), 
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 134219728
*Jun 27 09:31:41.955: IPSEC(create_sa): sa created,
  (sa) sa_dest= 209.165.200.2, sa_prot= 50, 
    sa_spi= 0x4E6B990F(1315674383), 
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 134219729
VPN-Gateway2#
*Jun 27 09:32:31.979: ISAKMP:(0:1:SW:1):purging node 1546295295


PAT-Router#debug ip nat detail
IP NAT detailed debugging is on
PAT-Router#show debug
Generic IP:
  IP NAT detailed debugging is on
PAT-Router#

!--- The "i" in this line indicates the packet is traveling from the !--- inside to the outside (from a NAT perspective) interface. The number in !--- the brackets is the identification number in the IP packet. This is !--- useful when correlating information with sniffer traces taken with a !--- network analyzer while troubleshooting problems.

*Jun 27 09:31:35.375: NAT*: i: udp (172.16.1.2, 500) -> (209.165.200.2, 500) [66]

!--- The "s" in this next line shows the source address of the packet and how it is !--- being translated. 

*Jun 27 09:31:35.375: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [66]
*Jun 27 09:31:36.475: NAT*: o: udp (209.165.200.2, 500) -> (209.165.201.2, 500) [66]     
*Jun 27 09:31:36.475: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [66]
*Jun 27 09:31:36.683: NAT*: i: udp (172.16.1.2, 500) -> (209.165.200.2, 500) [67]
*Jun 27 09:31:36.683: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [67]
*Jun 27 09:31:38.595: NAT*: o: udp (209.165.200.2, 500) -> (209.165.201.2, 500) [67]
*Jun 27 09:31:38.595: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [67]
*Jun 27 09:31:38.823: NAT*: i: udp (172.16.1.2, 4500) -> (209.165.200.2, 4500) [68]
*Jun 27 09:31:38.823: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [68]
*Jun 27 09:31:40.163: NAT*: o: udp (209.165.200.2, 4500) -> (209.165.201.2, 4500) [68]     
*Jun 27 09:31:40.163: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [68]
*Jun 27 09:31:40.255: NAT*: i: udp (172.16.1.2, 4500) -> (209.165.200.2, 4500) [69]
*Jun 27 09:31:40.255: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [69]
*Jun 27 09:31:40.395: NAT*: i: udp (172.16.1.2, 4500) -> (209.165.200.2, 4500) [70]
*Jun 27 09:31:40.395: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [70]
*Jun 27 09:31:41.747: NAT*: o: udp (209.165.200.2, 4500) -> (209.165.201.2, 4500) [69]
*Jun 27 09:31:41.747: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [69]
*Jun 27 09:31:41.839: NAT*: i: udp (172.16.1.2, 4500) -> (209.165.200.2, 4500) [71]
*Jun 27 09:31:41.839: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [71]
*Jun 27 09:31:43.463: NAT*: i: udp (172.16.1.2, 4500) -> (209.165.200.2, 4500) [72]
*Jun 27 09:31:43.463: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [72]
*Jun 27 09:31:43.523: NAT*: o: udp (209.165.200.2, 4500) -> (209.165.201.2, 4500) [70]
*Jun 27 09:31:43.523: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [70]
*Jun 27 09:33:27.975: NAT*: i: udp (172.16.1.2, 4500) -> (209.165.200.2, 4500) [73]
*Jun 27 09:33:27.975: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [73]
*Jun 27 09:33:28.067: NAT*: o: udp (209.165.200.2, 4500) -> (209.165.201.2, 4500) [71]
*Jun 27 09:33:28.067: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [71]
*Jun 27 09:33:28.115: NAT*: i: udp (172.16.1.2, 4500) -> (209.165.200.2, 4500) [74]
*Jun 27 09:33:28.115: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [74]
*Jun 27 09:33:28.167: NAT*: o: udp (209.165.200.2, 4500) -> (209.165.201.2, 4500) [72]
*Jun 27 09:33:28.167: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [72]
*Jun 27 09:33:28.227: NAT*: i: udp (172.16.1.2, 4500) -> (209.165.200.2, 4500) [75]
*Jun 27 09:33:28.227: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [75]
*Jun 27 09:33:28.283: NAT*: o: udp (209.165.200.2, 4500) -> (209.165.201.2, 4500) [73]
*Jun 27 09:33:28.283: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [73]
*Jun 27 09:33:28.355: NAT*: i: udp (172.16.1.2, 4500) -> (209.165.200.2, 4500) [76]
*Jun 27 09:33:28.355: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [76]
*Jun 27 09:33:28.407: NAT*: o: udp (209.165.200.2, 4500) -> (209.165.201.2, 4500) [74]
*Jun 27 09:33:28.407: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [74]
*Jun 27 09:33:28.455: NAT*: i: udp (172.16.1.2, 4500) -> (209.165.200.2, 4500) [77]
*Jun 27 09:33:28.455: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [77]
*Jun 27 09:33:28.487: NAT*: o: udp (209.165.200.2, 4500) -> (209.165.201.2, 4500) [75]
*Jun 27 09:33:28.487: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [75]

沒有IPSec NAT透明度的故障排除

  • debug crypto ipsec -顯示第2階段的IPSec協商。

  • debug crypto isakmp -顯示第1階段的ISAKMP協商。

  • debug ip nat detail -檢查路由器所執行的NAT。

以下是命令輸出示例。

VPN-Gateway1#debug crypto ipsec
Crypto IPSEC debugging is on
VPN-Gateway1#debug crypto isakmp
Crypto ISAKMP debugging is on
VPN-Gateway1#show debug
Cryptographic Subsystem:
  Crypto ISAKMP debugging is on
  Crypto IPSEC debugging is on

 
!--- These debugs appeared after a ping !--- was attempted from PC2 to PC1.


*Jun 27 09:49:58.351: ISAKMP (0:0): received packet from 209.165.201.2 
                      dport 500 sport 500 Global (N) NEW SA
*Jun 27 09:49:58.351: ISAKMP: Created a peer struct for 209.165.201.2, 
                      peer port 500
*Jun 27 09:49:58.351: ISAKMP: Locking peer struct 0x2C50328, IKE refcount 1 
                      for crypto_isakmp_process_block
*Jun 27 09:49:58.351: ISAKMP: local port 500, remote port 500
*Jun 27 09:49:58.991: insert sa successfully sa = 29D2E80
*Jun 27 09:49:58.991: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
*Jun 27 09:49:58.991: ISAKMP:(0:1:SW:1):Old State = IKE_READY  New State = 
                      IKE_R_MM1 

*Jun 27 09:49:59.151: ISAKMP:(0:1:SW:1): processing SA payload. message ID = 0
*Jun 27 09:49:59.151: ISAKMP: Looking for a matching key for 209.165.201.2 
                      in default : success
*Jun 27 09:49:59.151: ISAKMP:(0:1:SW:1):found peer pre-shared key matching 
                      209.165.201.2
*Jun 27 09:49:59.151: ISAKMP:(0:1:SW:1): local preshared key found
*Jun 27 09:49:59.151: ISAKMP : Scanning profiles for xauth ...
*Jun 27 09:49:59.151: ISAKMP:(0:1:SW:1):Checking ISAKMP transform 1 against 
                      priority 10 policy
*Jun 27 09:49:59.151: ISAKMP:      encryption DES-CBC
*Jun 27 09:49:59.151: ISAKMP:      hash SHA
*Jun 27 09:49:59.151: ISAKMP:      default group 1
*Jun 27 09:49:59.151: ISAKMP:      auth pre-share
*Jun 27 09:49:59.151: ISAKMP:      life type in seconds
*Jun 27 09:49:59.151: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80 
*Jun 27 09:49:59.151: ISAKMP:(0:1:SW:1):atts are acceptable. Next payload is 0
*Jun 27 09:49:59.151: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_MAIN_MODE
*Jun 27 09:49:59.151: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM1  
                      New State = IKE_R_MM1 

*Jun 27 09:49:59.223: ISAKMP:(0:1:SW:1): sending packet to 209.165.201.2 
                       my_port 500 peer_port 500 (R) MM_SA_SETUP
*Jun 27 09:49:59.223: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                       IKE_PROCESS_COMPLETE
*Jun 27 09:49:59.223: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM1  New State = 
                      IKE_R_MM2 

*Jun 27 09:49:59.711: ISAKMP (0:134217729): received packet from 209.165.201.2 
                      dport 500 sport 500 Global (R) MM_SA_SETUP
*Jun 27 09:49:59.711: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, 
                      IKE_MM_EXCH
*Jun 27 09:49:59.711: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM2  
                      New State = IKE_R_MM3 

*Jun 27 09:49:59.763: ISAKMP:(0:1:SW:1): processing KE payload. message ID = 0
*Jun 27 09:49:59.763: ISAKMP:(0:1:SW:1): processing NONCE payload. 
                      message ID = 0
*Jun 27 09:49:59.911: ISAKMP: Looking for a matching key for 209.165.201.2 
                      in default : success
*Jun 27 09:49:59.911: ISAKMP:(0:1:SW:1):found peer pre-shared key matching 
                      209.165.201.2
*Jun 27 09:49:59.911: ISAKMP:(0:1:SW:1):SKEYID state generated
*Jun 27 09:49:59.911: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:49:59.911: ISAKMP:(0:1:SW:1): vendor ID is Unity
*Jun 27 09:49:59.911: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:49:59.911: ISAKMP:(0:1:SW:1): vendor ID is DPD
*Jun 27 09:49:59.911: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:49:59.911: ISAKMP:(0:1:SW:1): speaking to another IOS box!
*Jun 27 09:49:59.911: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_MAIN_MODE
*Jun 27 09:49:59.911: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM3  
                      New State = IKE_R_MM3 

*Jun 27 09:50:00.051: ISAKMP:(0:1:SW:1): sending packet to 209.165.201.2 
                      my_port 500 peer_port 500 (R) MM_KEY_EXCH
*Jun 27 09:50:00.051: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_COMPLETE
*Jun 27 09:50:00.051: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM3  New State = 
                       IKE_R_MM4 

*Jun 27 09:50:00.743: ISAKMP (0:134217729): received packet from 209.165.201.2 
                       dport 500 sport 500 Global (R) MM_KEY_EXCH
*Jun 27 09:50:00.743: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, 
                      IKE_MM_EXCH
*Jun 27 09:50:00.743: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM4  
                      New State = IKE_R_MM5 

*Jun 27 09:50:00.811: ISAKMP:(0:1:SW:1): processing ID payload. message ID = 0
*Jun 27 09:50:00.811: ISAKMP (0:134217729): ID payload 
        next-payload : 8
        type         : 1 
        address      : 172.16.1.2 
        protocol     : 17 
        port         : 500 
        length       : 12
*Jun 27 09:50:00.811: ISAKMP:(0:1:SW:1):: peer matches *none* of the profiles
*Jun 27 09:50:00.811: ISAKMP:(0:1:SW:1): processing HASH payload. message ID = 0
*Jun 27 09:50:00.811: ISAKMP:(0:1:SW:1): processing NOTIFY INITIAL_CONTACT 
                       protocol 1
        spi 0, message ID = 0, sa = 29D2E80
*Jun 27 09:50:00.811: ISAKMP:(0:1:SW:1):SA authentication status:
        authenticated
*Jun 27 09:50:00.811: ISAKMP:(0:1:SW:1): Process initial contact,
                    bring down existing phase 1 and 2 SA's with local 
                     209.165.200.2 remote 
                     209.165.201.2 remote port 500
*Jun 27 09:50:00.811: ISAKMP:(0:1:SW:1):SA authentication status:
        authenticated
*Jun 27 09:50:00.811: ISAKMP:(0:1:SW:1):SA has been authenticated with 
                      209.165.201.2
*Jun 27 09:50:00.811: ISAKMP: Trying to insert a peer 
                      209.165.200.2/209.165.201.2/500/,  and inserted successfully.
*Jun 27 09:50:00.811: ISAKMP:(0:1:SW:1):: peer matches *none* of the profiles
*Jun 27 09:50:00.811: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_MAIN_MODE
*Jun 27 09:50:00.811: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM5  
                      New State = IKE_R_MM5 

*Jun 27 09:50:00.851: IPSEC(key_engine): got a queue event with 1 kei messages
*Jun 27 09:50:00.963: ISAKMP:(0:1:SW:1):SA is doing pre-shared key 
                        authentication using id type ID_IPV4_ADDR
*Jun 27 09:50:00.963: ISAKMP (0:134217729): ID payload 
        next-payload : 8
        type         : 1 
        address      : 209.165.200.2 
        protocol     : 17 
        port         : 500 
        length       : 12
*Jun 27 09:50:00.963: ISAKMP:(0:1:SW:1):Total payload length: 12
*Jun 27 09:50:00.963: ISAKMP:(0:1:SW:1): sending packet to 209.165.201.2 
                      my_port 500 peer_port 500 (R) MM_KEY_EXCH
*Jun 27 09:50:00.963: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_COMPLETE
*Jun 27 09:50:00.963: ISAKMP:(0:1:SW:1):Old State = IKE_R_MM5  New State = 
                      IKE_P1_COMPLETE 

*Jun 27 09:50:01.043: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                       IKE_PHASE1_COMPLETE
*Jun 27 09:50:01.043: ISAKMP:(0:1:SW:1):Old State = IKE_P1_COMPLETE  
                       New State = IKE_P1_COMPLETE 

*Jun 27 09:50:01.403: ISAKMP (0:134217729): received packet from 209.165.201.2 
                      dport 500 sport 500 Global (R) QM_IDLE      
*Jun 27 09:50:01.403: ISAKMP: set new node 1689610294 to QM_IDLE      
*Jun 27 09:50:01.403: ISAKMP:(0:1:SW:1): processing HASH payload. message 
                       ID = 1689610294
*Jun 27 09:50:01.403: ISAKMP:(0:1:SW:1): processing SA payload. message 
                      ID = 1689610294
*Jun 27 09:50:01.403: ISAKMP:(0:1:SW:1):Checking IPSec proposal 1
*Jun 27 09:50:01.403: ISAKMP: transform 1, ESP_DES
*Jun 27 09:50:01.403: ISAKMP:   attributes in transform:
*Jun 27 09:50:01.403: ISAKMP:      encaps is 1 (Tunnel)
*Jun 27 09:50:01.403: ISAKMP:      SA life type in seconds
*Jun 27 09:50:01.403: ISAKMP:      SA life duration (basic) of 3600
*Jun 27 09:50:01.403: ISAKMP:      SA life type in kilobytes
*Jun 27 09:50:01.403: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0 
*Jun 27 09:50:01.403: ISAKMP:      authenticator is HMAC-MD5
*Jun 27 09:50:01.403: ISAKMP:(0:1:SW:1):atts are acceptable.
*Jun 27 09:50:01.403: IPSEC(validate_proposal_request): proposal part #1,
  (key eng. msg.) INBOUND local= 209.165.200.2, remote= 209.165.201.2, 
    local_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel), 
    lifedur= 0s and 0kb, 
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x2
*Jun 27 09:50:01.403: IPSEC(kei_proxy): head = mymap, map->ivrf = ,
                      kei->ivrf = 
*Jun 27 09:50:01.403: ISAKMP:(0:1:SW:1): processing NONCE payload. 
                      message ID = 1689610294
*Jun 27 09:50:01.403: ISAKMP:(0:1:SW:1): processing ID payload. 
                      message ID = 1689610294
*Jun 27 09:50:01.403: ISAKMP:(0:1:SW:1): processing ID payload. 
                      message ID = 1689610294
*Jun 27 09:50:01.403: ISAKMP:(0:1:SW:1): asking for 1 spis from ipsec
*Jun 27 09:50:01.403: ISAKMP:(0:1:SW:1):Node 1689610294, Input = 
                      IKE_MESG_FROM_PEER, IKE_QM_EXCH
*Jun 27 09:50:01.403: ISAKMP:(0:1:SW:1):Old State = IKE_QM_READY  
                       New State = IKE_QM_SPI_STARVE
*Jun 27 09:50:01.443: IPSEC(key_engine): got a queue event with 1 kei messages
*Jun 27 09:50:01.443: IPSEC(spi_response): getting spi 3052955580 for SA 
        from 209.165.200.2   to 209.165.201.2   for prot 3
*Jun 27 09:50:01.463: ISAKMP: received ke message (2/1)
*Jun 27 09:50:01.971: ISAKMP:(0:1:SW:1): sending packet to 209.165.201.2 
                      my_port 500 peer_port 500 (R) QM_IDLE      
*Jun 27 09:50:01.971: ISAKMP:(0:1:SW:1):Node 1689610294, Input = 
                      IKE_MESG_FROM_IPSEC, IKE_SPI_REPLY
*Jun 27 09:50:01.971: ISAKMP:(0:1:SW:1):Old State = IKE_QM_SPI_STARVE  
                      New State = IKE_QM_R_QM2
*Jun 27 09:50:02.303: ISAKMP (0:134217729): received packet from 209.165.201.2 
                       dport 500 sport 500 Global (R) QM_IDLE      
*Jun 27 09:50:02.303: IPSec: Flow_switching Allocated flow for flow_id 
                      134217735 
*Jun 27 09:50:02.303: IPSec: Flow_switching Allocated flow for flow_id 134217736 
*Jun 27 09:50:03.203: %CRYPTO-5-SESSION_STATUS: Crypto tunnel is UP  .  
                      Peer 209.165.201.2:500       Id: 172.16.1.2
*Jun 27 09:50:03.203: ISAKMP: Locking peer struct 0x2C50328, IPSEC refcount 
                       1 for for stuff_ke
*Jun 27 09:50:03.203: ISAKMP:(0:1:SW:1): Creating IPSec SAs
*Jun 27 09:50:03.203:         inbound SA from 209.165.201.2 to 209.165.200.2 
                              (f/i)  0/ 0
                              (proxy 172.16.2.0 to 192.168.1.0)
*Jun 27 09:50:03.203:         has spi 0xB5F867BC and conn_id 2000 and flags 2
*Jun 27 09:50:03.203:         lifetime of 3600 seconds
*Jun 27 09:50:03.203:         lifetime of 4608000 kilobytes
*Jun 27 09:50:03.203:         has client flags 0x0
*Jun 27 09:50:03.203:         outbound SA from 209.165.200.2 to 209.165.201.2 
                               (f/i) 0/0
                              (proxy 192.168.1.0 to 172.16.2.0)
*Jun 27 09:50:03.203:         has spi -392560059 and conn_id 2001 and flags A
*Jun 27 09:50:03.203:         lifetime of 3600 seconds
*Jun 27 09:50:03.203:         lifetime of 4608000 kilobytes
*Jun 27 09:50:03.203:         has client flags 0x0
*Jun 27 09:50:03.203: ISAKMP:(0:1:SW:1):deleting node 1689610294 error 
                      FALSE reason "quick mode done (await)"
*Jun 27 09:50:03.203: ISAKMP:(0:1:SW:1):Node 1689610294, Input = 
                     IKE_MESG_FROM_PEER, IKE_QM_EXCH
*Jun 27 09:50:03.203: ISAKMP:(0:1:SW:1):Old State = IKE_QM_R_QM2  
                       New State = IKE_QM_PHASE2_COMPLETE
*Jun 27 09:50:03.231: IPSEC(key_engine): got a queue event with 2 kei messages
*Jun 27 09:50:03.231: IPSEC(initialize_sas): ,
  (key eng. msg.) INBOUND local= 209.165.200.2, remote= 209.165.201.2, 
    local_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel), 
    lifedur= 3600s and 4608000kb, 
    spi= 0xB5F867BC(3052955580), conn_id= 134219728, keysize= 0, flags= 0x2
*Jun 27 09:50:03.231: IPSEC(initialize_sas): ,
  (key eng. msg.) OUTBOUND local= 209.165.200.2, remote= 209.165.201.2, 
    local_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel), 
    lifedur= 3600s and 4608000kb, 
    spi= 0xE89A0245(3902407237), conn_id= 134219729, keysize= 0, flags= 0xA
*Jun 27 09:50:03.231: IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf = 
*Jun 27 09:50:03.231: IPSEC(crypto_ipsec_sa_find_ident_head): 
                      reconnecting with the same proxies and 209.165.201.2
*Jun 27 09:50:03.231: IPSEC(mtree_add_ident): src 192.168.1.0, 
                      dest 172.16.2.0, dest_port 0

*Jun 27 09:50:03.231: IPSEC(create_sa): sa created,
  (sa) sa_dest= 209.165.200.2, sa_prot= 50, 
    sa_spi= 0xB5F867BC(3052955580), 
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 134219728
*Jun 27 09:50:03.231: IPSEC(create_sa): sa created,
  (sa) sa_dest= 209.165.201.2, sa_prot= 50, 
    sa_spi= 0xE89A0245(3902407237), 
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 134219729

*Jun 27 09:50:53.231: ISAKMP:(0:1:SW:1):purging node 1689610294

VPN-Gateway2#debug crypto ipsec
Crypto IPSEC debugging is on
VPN-Gateway2#debug crypto isakmp
Crypto ISAKMP debugging is on
VPN-Gateway2#show debug
Cryptographic Subsystem:
  Crypto ISAKMP debugging is on
  Crypto IPSEC debugging is on
VPN-Gateway2#

 
!--- These debugs appeared after a ping !--- was attempted from PC2 to PC1.


*Jun 27 09:49:57.799: IPSEC(sa_request): ,
  (key eng. msg.) OUTBOUND local= 172.16.1.2, remote= 209.165.200.2, 
    local_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel), 
    lifedur= 3600s and 4608000kb, 
    spi= 0xE89A0245(3902407237), conn_id= 0, keysize= 0, flags= 0x400A
*Jun 27 09:49:57.807: ISAKMP: received ke message (1/1)
*Jun 27 09:49:57.807: ISAKMP:(0:0:N/A:0): SA request profile is (NULL)
*Jun 27 09:49:57.807: ISAKMP: Created a peer struct for 209.165.200.2, 
                      peer port 500
*Jun 27 09:49:57.807: ISAKMP: Locking peer struct 0x2BEDC78, IKE refcount 
                      1 for isakmp_initiator
*Jun 27 09:49:57.807: ISAKMP: local port 500, remote port 500
*Jun 27 09:49:57.839: ISAKMP: set new node 0 to QM_IDLE      
*Jun 27 09:49:57.839: insert sa successfully sa = 2CB1E80
*Jun 27 09:49:57.839: ISAKMP:(0:1:SW:1):Can not start Aggressive mode, 
                       trying Main mode.
*Jun 27 09:49:57.839: ISAKMP: Looking for a matching key for 209.165.200.2 
                      in default : success
*Jun 27 09:49:57.839: ISAKMP:(0:1:SW:1):found peer pre-shared key matching 
                       209.165.200.2
*Jun 27 09:49:57.839: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_IPSEC, 
                       IKE_SA_REQ_MM
*Jun 27 09:49:57.839: ISAKMP:(0:1:SW:1):Old State = IKE_READY  
                      New State = IKE_I_MM1 

*Jun 27 09:49:57.839: ISAKMP:(0:1:SW:1): beginning Main Mode exchange
*Jun 27 09:49:57.839: ISAKMP:(0:1:SW:1): sending packet to 209.165.200.2 
                      my_port 500 peer_port 500 (I) MM_NO_STATE
*Jun 27 09:49:59.099: ISAKMP (0:134217729): received packet from 209.165.200.2 
                      dport 500 sport 500 Global (I) MM_NO_STATE
*Jun 27 09:49:59.099: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
*Jun 27 09:49:59.099: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM1  New State = 
                      IKE_I_MM2 

*Jun 27 09:49:59.139: ISAKMP:(0:1:SW:1): processing SA payload. message ID = 0
*Jun 27 09:49:59.139: ISAKMP: Looking for a matching key for 209.165.200.2 
                       in default : success
*Jun 27 09:49:59.139: ISAKMP:(0:1:SW:1):found peer pre-shared key matching 
                       209.165.200.2
*Jun 27 09:49:59.139: ISAKMP:(0:1:SW:1): local preshared key found
*Jun 27 09:49:59.139: ISAKMP : Scanning profiles for xauth ...
*Jun 27 09:49:59.139: ISAKMP:(0:1:SW:1):Checking ISAKMP transform 1 against 
                       priority 10 policy
*Jun 27 09:49:59.139: ISAKMP:      encryption DES-CBC
*Jun 27 09:49:59.139: ISAKMP:      hash SHA
*Jun 27 09:49:59.139: ISAKMP:      default group 1
*Jun 27 09:49:59.139: ISAKMP:      auth pre-share
*Jun 27 09:49:59.139: ISAKMP:      life type in seconds
*Jun 27 09:49:59.139: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80 
*Jun 27 09:49:59.139: ISAKMP:(0:1:SW:1):atts are acceptable. Next payload is 0
*Jun 27 09:49:59.139: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_MAIN_MODE
*Jun 27 09:49:59.139: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM2  New State = 
                      IKE_I_MM2 

*Jun 27 09:49:59.259: ISAKMP:(0:1:SW:1): sending packet to 209.165.200.2 
                      my_port 500 peer_port 500 (I) MM_SA_SETUP
*Jun 27 09:49:59.259: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_COMPLETE
*Jun 27 09:49:59.259: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM2  New State = 
                       IKE_I_MM3 

*Jun 27 09:49:59.919: ISAKMP (0:134217729): received packet from 209.165.200.2 
                       dport 500 sport 500 Global (I) MM_SA_SETUP
*Jun 27 09:49:59.919: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
*Jun 27 09:49:59.919: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM3  
                       New State = IKE_I_MM4 

*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1): processing KE payload. message ID = 0
*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1): processing NONCE payload. message ID = 0
*Jun 27 09:49:59.947: ISAKMP: Looking for a matching key for 209.165.200.2 
                      in default : success
*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1):found peer pre-shared key matching 
                      209.165.200.2
*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1):SKEYID state generated
*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1): vendor ID is Unity
*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1): vendor ID is DPD
*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1): processing vendor id payload
*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1): speaking to another IOS box!
*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_MAIN_MODE
*Jun 27 09:49:59.947: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM4  
                       New State = IKE_I_MM4 

*Jun 27 09:50:00.059: ISAKMP:(0:1:SW:1):Send initial contact
*Jun 27 09:50:00.059: ISAKMP:(0:1:SW:1):SA is doing pre-shared key 
                        authentication using id type ID_IPV4_ADDR
*Jun 27 09:50:00.059: ISAKMP (0:134217729): ID payload 
        next-payload : 8
        type         : 1 
        address      : 172.16.1.2 
        protocol     : 17 
        port         : 500 
        length       : 12
*Jun 27 09:50:00.059: ISAKMP:(0:1:SW:1):Total payload length: 12
*Jun 27 09:50:00.059: ISAKMP:(0:1:SW:1): sending packet to 209.165.200.2 
                       my_port 500 peer_port 500 (I) MM_KEY_EXCH
*Jun 27 09:50:00.059: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_COMPLETE
*Jun 27 09:50:00.059: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM4  
                       New State = IKE_I_MM5 

*Jun 27 09:50:00.827: ISAKMP (0:134217729): received packet from 209.165.200.2 
                      dport 500 sport 500 Global (I) MM_KEY_EXCH
*Jun 27 09:50:00.827: ISAKMP:(0:1:SW:1):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
*Jun 27 09:50:00.827: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM5  
                       New State = IKE_I_MM6 

*Jun 27 09:50:00.859: ISAKMP:(0:1:SW:1): processing ID payload. message ID = 0
*Jun 27 09:50:00.859: ISAKMP (0:134217729): ID payload 
        next-payload : 8
        type         : 1 
        address      : 209.165.200.2 
        protocol     : 17 
        port         : 500 
        length       : 12
*Jun 27 09:50:00.859: ISAKMP:(0:1:SW:1): processing HASH payload. message ID = 0
*Jun 27 09:50:00.859: ISAKMP:(0:1:SW:1):SA authentication status:
        authenticated
*Jun 27 09:50:00.859: ISAKMP:(0:1:SW:1):SA has been authenticated 
                      with 209.165.200.2
*Jun 27 09:50:00.859: ISAKMP:(0:1:SW:1):: peer matches *none* of the profiles
*Jun 27 09:50:00.859: ISAKMP: Trying to insert a peer 172.16.1.2/209.165.200.2/500/,
                        and inserted successfully.
*Jun 27 09:50:00.859: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_MAIN_MODE
*Jun 27 09:50:00.859: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM6  
                       New State = IKE_I_MM6 

*Jun 27 09:50:00.919: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PROCESS_COMPLETE
*Jun 27 09:50:00.919: ISAKMP:(0:1:SW:1):Old State = IKE_I_MM6  
                        New State = IKE_P1_COMPLETE 

*Jun 27 09:50:00.959: ISAKMP:(0:1:SW:1):beginning Quick Mode exchange, 
                       M-ID of 1689610294
*Jun 27 09:50:01.007: ISAKMP:(0:1:SW:1): sending packet to 209.165.200.2 
                       my_port 500 peer_port 500 (I) QM_IDLE      
*Jun 27 09:50:01.007: ISAKMP:(0:1:SW:1):Node 1689610294, Input = 
                       IKE_MESG_INTERNAL, IKE_INIT_QM
*Jun 27 09:50:01.007: ISAKMP:(0:1:SW:1):Old State = IKE_QM_READY  
                       New State = IKE_QM_I_QM1
*Jun 27 09:50:01.007: ISAKMP:(0:1:SW:1):Input = IKE_MESG_INTERNAL, 
                      IKE_PHASE1_COMPLETE
*Jun 27 09:50:01.007: ISAKMP:(0:1:SW:1):Old State = IKE_P1_COMPLETE  
                       New State = IKE_P1_COMPLETE 

*Jun 27 09:50:01.839: ISAKMP (0:134217729): received packet from 
                      209.165.200.2 dport 500 sport 500 Global (I) QM_IDLE      
*Jun 27 09:50:01.839: ISAKMP:(0:1:SW:1): processing HASH payload. 
                      message ID = 1689610294
*Jun 27 09:50:01.839: ISAKMP:(0:1:SW:1): processing SA payload. 
                      message ID = 1689610294
*Jun 27 09:50:01.839: ISAKMP:(0:1:SW:1):Checking IPSec proposal 1
*Jun 27 09:50:01.839: ISAKMP: transform 1, ESP_DES
*Jun 27 09:50:01.839: ISAKMP:   attributes in transform:
*Jun 27 09:50:01.839: ISAKMP:      encaps is 1 (Tunnel)
*Jun 27 09:50:01.839: ISAKMP:      SA life type in seconds
*Jun 27 09:50:01.839: ISAKMP:      SA life duration (basic) of 3600
*Jun 27 09:50:01.839: ISAKMP:      SA life type in kilobytes
*Jun 27 09:50:01.839: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0 
*Jun 27 09:50:01.839: ISAKMP:      authenticator is HMAC-MD5
*Jun 27 09:50:01.839: ISAKMP:(0:1:SW:1):atts are acceptable.
*Jun 27 09:50:01.839: IPSEC(validate_proposal_request): proposal part #1,
  (key eng. msg.) INBOUND local= 172.16.1.2, remote= 209.165.200.2, 
    local_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel), 
    lifedur= 0s and 0kb, 
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x2
*Jun 27 09:50:01.839: IPSEC(kei_proxy): head = mymap, map->ivrf = ,
                           kei->ivrf = 
*Jun 27 09:50:01.839: ISAKMP:(0:1:SW:1): processing NONCE payload. 
                       message ID = 1689610294
*Jun 27 09:50:01.839: ISAKMP:(0:1:SW:1): processing ID payload. 
                       message ID = 1689610294
*Jun 27 09:50:01.839: ISAKMP:(0:1:SW:1): processing ID payload. 
                        message ID = 1689610294
*Jun 27 09:50:01.839: IPSec: Flow_switching Allocated flow for flow_id 134217731 
*Jun 27 09:50:01.839: IPSec: Flow_switching Allocated flow for flow_id 134217732 
*Jun 27 09:50:01.899: %CRYPTO-5-SESSION_STATUS: Crypto tunnel is UP  .  
                      Peer 209.165.200.2:500       Id: 209.165.200.2
*Jun 27 09:50:01.899: ISAKMP: Locking peer struct 0x2BEDC78, IPSEC
                       refcount 1 for for stuff_ke
*Jun 27 09:50:01.899: ISAKMP:(0:1:SW:1): Creating IPSec SAs
*Jun 27 09:50:01.899:         inbound SA from 209.165.200.2 to 172.16.1.2 
                               (f/i)  0/ 0
                              (proxy 192.168.1.0 to 172.16.2.0)
*Jun 27 09:50:01.899:         has spi 0xE89A0245 and conn_id 2000 and flags 2
*Jun 27 09:50:01.899:         lifetime of 3600 seconds
*Jun 27 09:50:01.899:         lifetime of 4608000 kilobytes
*Jun 27 09:50:01.899:         has client flags 0x0
*Jun 27 09:50:01.899:         outbound SA from 172.16.1.2 to 209.165.200.2 
                               (f/i) 0/0
                                (proxy 172.16.2.0 to 192.168.1.0)
*Jun 27 09:50:01.899:         has spi -1242011716 and conn_id 2001 and flags A
*Jun 27 09:50:01.899:         lifetime of 3600 seconds
*Jun 27 09:50:01.899:         lifetime of 4608000 kilobytes
*Jun 27 09:50:01.899:         has client flags 0x0
*Jun 27 09:50:01.899: ISAKMP:(0:1:SW:1): sending packet to 209.165.200.2 
                       my_port 500 peer_port 500 (I) QM_IDLE      
*Jun 27 09:50:01.899: ISAKMP:(0:1:SW:1):deleting node 1689610294 error 
                       FALSE reason ""
*Jun 27 09:50:01.899: ISAKMP:(0:1:SW:1):Node 1689610294, Input = 
                       IKE_MESG_FROM_PEER, IKE_QM_EXCH
*Jun 27 09:50:01.899: ISAKMP:(0:1:SW:1):Old State = IKE_QM_I_QM1  
                        New State = IKE_QM_PHASE2_COMPLETE
*Jun 27 09:50:01.907: IPSEC(key_engine): got a queue event with 2 kei messages
*Jun 27 09:50:01.907: IPSEC(initialize_sas): ,
  (key eng. msg.) INBOUND local= 172.16.1.2, remote= 209.165.200.2, 
    local_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel), 
    lifedur= 3600s and 4608000kb, 
    spi= 0xE89A0245(3902407237), conn_id= 134219728, keysize= 0, flags= 0x2
*Jun 27 09:50:01.907: IPSEC(initialize_sas): ,
  (key eng. msg.) OUTBOUND local= 172.16.1.2, remote= 209.165.200.2, 
    local_proxy= 172.16.2.0/255.255.255.0/0/0 (type=4), 
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac  (Tunnel), 
    lifedur= 3600s and 4608000kb, 
    spi= 0xB5F867BC(3052955580), conn_id= 134219729, keysize= 0,flags= 0xA
*Jun 27 09:50:01.907: IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf = 
*Jun 27 09:50:01.907: IPSEC(crypto_ipsec_sa_find_ident_head): 
                      reconnecting with the same proxies and 209.165.200.2
*Jun 27 09:50:01.907: IPSEC(mtree_add_ident): src 172.16.2.0, dest 
                       192.168.1.0, dest_port 0

*Jun 27 09:50:01.907: IPSEC(create_sa): sa created,
  (sa) sa_dest= 172.16.1.2, sa_prot= 50, 
    sa_spi= 0xE89A0245(3902407237), 
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 134219728
*Jun 27 09:50:01.907: IPSEC(create_sa): sa created,
  (sa) sa_dest= 209.165.200.2, sa_prot= 50, 
    sa_spi= 0xB5F867BC(3052955580), 
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 134219729

*Jun 27 09:50:51.927: ISAKMP:(0:1:SW:1):purging node 1689610294


PAT-Router#debug ip nat detail
IP NAT detailed debugging is on
PAT-Router#show debug
Generic IP:
  IP NAT detailed debugging is on
PAT-Router#

!--- The "i" in this line indicates the packet is traveling from the !--- inside to the outside (from a NAT perspective) interface. The number in !--- the brackets is the identification number in the IP packet. This is !--- useful when correlating information with sniffer traces taken with a !--- network analyzer while troubleshooting problems.

*Jun 27 09:49:57.727: NAT*: i: udp (172.16.1.2, 500) -> (209.165.200.2, 500) [94]

!--- The "s" in this line shows the source address of the packet and how it is !--- being translated. 

*Jun 27 09:49:57.727: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [94]
*Jun 27 09:49:58.927: NAT*: o: udp (209.165.200.2, 500) -> (209.165.201.2, 500) [100]     
*Jun 27 09:49:58.927: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [100]
*Jun 27 09:49:59.147: NAT*: i: udp (172.16.1.2, 500) -> (209.165.200.2, 500) [95]
*Jun 27 09:49:59.147: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [95]
*Jun 27 09:49:59.755: NAT*: o: udp (209.165.200.2, 500) -> (209.165.201.2, 500) [101]
*Jun 27 09:49:59.755: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [101]
*Jun 27 09:49:59.947: NAT*: i: udp (172.16.1.2, 500) -> (209.165.200.2, 500) [96]
*Jun 27 09:49:59.947: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [96]
*Jun 27 09:50:00.667: NAT*: o: udp (209.165.200.2, 500) -> (209.165.201.2, 500) [102]
*Jun 27 09:50:00.667: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [102]
*Jun 27 09:50:00.895: NAT*: i: udp (172.16.1.2, 500) -> (209.165.200.2, 500) [97]
*Jun 27 09:50:00.895: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [97]
*Jun 27 09:50:01.679: NAT*: o: udp (209.165.200.2, 500) -> (209.165.201.2, 500) [103]
*Jun 27 09:50:01.679: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [103]
*Jun 27 09:50:01.787: NAT*: i: udp (172.16.1.2, 500) -> (209.165.200.2, 500) [98]
*Jun 27 09:50:01.787: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [98]
*Jun 27 09:50:23.667: NAT*: i: esp (172.16.1.2, 26556) -> (209.165.200.2, 0) [99]
*Jun 27 09:50:23.667: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [99]
*Jun 27 09:50:23.715: NAT*: o: esp (209.165.200.2, -392560059) -> (209.165.201.2, 0) [104]     
*Jun 27 09:50:23.715: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [104]
*Jun 27 09:50:23.787: NAT*: i: esp (172.16.1.2, 26556) -> (209.165.200.2, 0) [100]
*Jun 27 09:50:23.787: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [100]
*Jun 27 09:50:23.847: NAT*: o: esp (209.165.200.2, 581) -> (209.165.201.2, 0) [105]
*Jun 27 09:50:23.847: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [105]
*Jun 27 09:50:23.915: NAT*: i: esp (172.16.1.2, 26556) -> (209.165.200.2, 0) [101]
*Jun 27 09:50:23.915: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [101]
*Jun 27 09:50:23.967: NAT*: o: esp (209.165.200.2, 581) -> (209.165.201.2, 0) [106]
*Jun 27 09:50:23.967: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [106]
*Jun 27 09:50:24.047: NAT*: i: esp (172.16.1.2, 26556) -> (209.165.200.2, 0) [102]
*Jun 27 09:50:24.047: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [102]
*Jun 27 09:50:24.095: NAT*: o: esp (209.165.200.2, 581) -> (209.165.201.2, 0) [107]
*Jun 27 09:50:24.095: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [107]
*Jun 27 09:50:24.207: NAT*: i: esp (172.16.1.2, 26556) -> (209.165.200.2, 0) [103]
*Jun 27 09:50:24.207: NAT*: s=172.16.1.2->209.165.201.2, d=209.165.200.2 [103]
*Jun 27 09:50:24.267: NAT*: o: esp (209.165.200.2, 581) -> (209.165.201.2, 0) [108]
*Jun 27 09:50:24.267: NAT*: s=209.165.200.2, d=209.165.201.2->172.16.1.2 [108]

相關資訊

修訂記錄

修訂 發佈日期 意見
1.0
21-May-2002
初始版本

這份文件是否有所幫助？

Feedback意見

讓思科協助您

本文件適用於這些產品