排除Nexus 7000系列交換機上的硬體轉發問題
下載選項
已更新: 2016 年 10 月 6 日
文件 ID:200300
無偏見用語
本產品的文件集力求使用無偏見用語。針對本文件集的目的，無偏見係定義為未根據年齡、身心障礙、性別、種族身分、民族身分、性別傾向、社會經濟地位及交織性表示歧視的用語。由於本產品軟體使用者介面中硬式編碼的語言、根據 RFP 文件使用的語言，或引用第三方產品的語言，因此本文件中可能會出現例外狀況。深入瞭解思科如何使用包容性用語。
關於此翻譯
思科已使用電腦和人工技術翻譯本文件，讓全世界的使用者能夠以自己的語言理解支援內容。請注意，即使是最佳機器翻譯，也不如專業譯者翻譯的內容準確。Cisco Systems, Inc. 對這些翻譯的準確度概不負責，並建議一律查看原始英文文件（提供連結）。
簡介
本文檔介紹如何對Cisco Nexus 7000系列交換機的F3系列模組上的硬體轉發問題進行故障排除。
必要條件
需求
思科建議您先熟悉Cisco Nexus作業系統(NX-OS)和基本Nexus架構，然後再繼續處理本文檔中介紹的資訊。
採用元件
本文中的資訊係根據以下軟體和硬體版本：
- Cisco Nexus 7000系列交換機(N7K)
- 思科N7K F3系列模組（N7K-F312FQ-25,12埠10/40千兆乙太網模組）
- Cisco NX-OS版本6.2.8a及更高版本
本文中的資訊是根據特定實驗室環境內的裝置所建立。文中使用到的所有裝置皆從已清除（預設）的組態來啟動。如果您的網路運作中，請確保您瞭解任何指令可能造成的影響。
背景資訊
本文檔主要介紹一些內建工具，用於在轉發表或控制平面的軟體部分用盡後進行硬體故障排除。其中一個工具是嵌入式邏輯分析器模組(ELAM)，它是一種特定應用積體電路(ASIC)，擷取單一封包，並顯示輸入封包在轉送後如何顯示在資料匯流排(DBUS)和結果匯流排(RBUS)上。
ASIC嵌入在轉發管道中，它可以即時捕獲資料包，而不會中斷效能或控制平面資源。這有助於回答以下問題：
- 封包是否已到達轉送引擎(FE)?
- 資料包是在哪個埠和VLAN上接收的？
- 封包如何顯示(第2層(L2)或第4層(L4)資料)?
- 資料包是如何更改的，它傳送到哪裡？
ELAM是一種功能強大、精確且無干擾的工具，最常用於從事硬體交換平台工作的思科技術支援中心(TAC)工程師。但是，必須知道ELAM工具一次只能捕獲一個資料包。即，在觸發ELAM之後收到的第一個資料包。
疑難排解
本節介紹在不使用分支電纜的部署中，以及在使用分支電纜的部署中，如何對F3系列模組上的ELAM進行故障排除。
排除不帶分支電纜的F3系列模組上的ELAM故障
本節中的示例使用的拓撲如下：
+-------------+ +-------------+ +------------+
| | | | | |
| | | | | |
| | e3/3-4 e3/1-2 | | e3/5 e3/7 | |
| N7K2 +-------------------+ N7K1 +---------------------+ N7K3 |
| +-------------------+ | .1 L3 .3 | |
| | Po1(Trunk) | | 192.168.13.0/24 | |
| | | | | |
+-------------+ +-------------+ +------------+
Vlan 10 SVI Vlan10 SVI
IP add 192.168.12.2/24 IP add 192.168.12.1/24
以下是關於此拓撲的一些註解：
- N7Ks運行NX-OS版本6.2.8a。
- 從N7K2 VLAN 10介面向遠端IP地址192.168.12.1傳送ping。
- ELAM捕獲N7K1上的資料包。
- 使用的是N7K-F312FQ-25，它是插入插槽3中的12埠10/40千兆乙太網模組。
開始對系統進行故障排除之前，應確認基本連線：
N7K2# ping 192.168.13.3
PING 192.168.13.3 (192.168.13.3): 56 data bytes
64 bytes from 192.168.13.3: icmp_seq=0 ttl=253 time=1.513 ms
64 bytes from 192.168.13.3: icmp_seq=1 ttl=253 time=1.062 ms
64 bytes from 192.168.13.3: icmp_seq=2 ttl=253 time=0.822 ms
64 bytes from 192.168.13.3: icmp_seq=3 ttl=253 time=0.830 ms
64 bytes from 192.168.13.3: icmp_seq=4 ttl=253 time=0.845 ms
--- 192.168.13.3 ping statistics ---
5 packets transmitted, 5 packets received, 0.00% packet loss
round-trip min/avg/max = 0.822/1.014/1.513 ms
N7K2# show ip route 192.168.13.3
IP Route Table for VRF "default"
'*' denotes best ucast next-hop
'**' denotes best mcast next-hop
'[x/y]' denotes [preference/metric]
'%<string>' in via output denotes VRF <string>
192.168.13.0/24, ubest/mbest: 1/0
*via 192.168.12.1, [1/0], 01:20:36, static
!--- The next command verifies the Address Resolution Protocol (ARP) for the next hop.
N7K2# show ip arp 192.168.12.1
----SNIP----
IP ARP Table
Total number of entries: 1
Address Age MAC Address Interface
192.168.12.1 00:10:29 e4c7.2210.a142 Vlan10
您還應驗證Supervisor引擎(Sup)和模組上的媒體訪問控制(MAC)地址學習功能，以瞭解下一跳：
N7K2# show mac address-table address e4c7.2210.a142
!--- This command output shows the MAC learning on the Sup (software).
Legend:
* - primary entry, G - Gateway MAC, (R) - Routed MAC, O - Overlay MAC
age - seconds since last seen,+ - primary entry using vPC Peer-Link,
(T) - True, (F) - False
VLAN MAC Address Type age Secure NTFY Ports/SWID.SSID.LID
---------+-----------------+--------+---------+------+----+------------------
* 10 e4c7.2210.a142 dynamic 120 F F Po1
此輸出顯示模組/硬體上的MAC學習；但是，為了瞭解介面，必須轉換索引：
N7K2# show hardware mac address-table 3 address e4c7.2210.a142
FE | Valid| PI| BD | MAC | Index | Stat| SW | Modi| Age| Tmr| GM| Sec|
| | | | | | ic | | fied|Byte| Sel| | ure|
---|------|---|------|---------------|-------|-----|-----|-----|----|----|---|----|
1 1 1 41 e4c7.2210.a142 0x00a2a 0 0x089 1 185 1 0 0
| TR| NT| RM| RMA| Cap| Fld|Always| PV | RD| NN| UC|PI_E8| VIF | SWID| SSWID| LID |
| AP| FY| | |ture| | Learn| | | | | | | | | |
|---|---|---|----|----|----|------|----|---|---|---|-----|-----|-----|------|-------|
0 0 0 0 0 0 0 0x00 0 0 1 0 0x000 0x000 0x000 0x00a2a
N7K2# show system internal pixm info ltl 0x00a2a
!--- This is the index that was received in the previous output.
---SNIP---
PC_TYPE PORT LTL RES_ID LTL_FLAG CB_FLAG MEMB_CNT
------------------------------------------------------------------------------
Normal Po1 0x0a2a 0x16000000 0x00000000 0x00000002 2
Member rbh rbh_cnt
Eth3/4 0x000000f0 0x04
Eth3/3 0x0000000f 0x04
---SNIP---
輸入以下命令可獲取虛擬裝置環境(VDC)編號(在本例中為3)，並直接檢查模組上的MAC:
N7K2# show vdc
---SNIP---
vdc_id vdc_name state mac type lc
------ -------- ----- ---------- --------- ---
3 N7K2 active e4:c7:22:10:a1:43 Ethernet f3
module-3#attach module 3
module-3# vdc 3
!--- This data is obtained from the previous command output.
module-3# show mac address-table address e4c7.2210.a142
Legend:
* - primary entry, G - Gateway MAC, (R) - Routed MAC, (d) - dec
Age - seconds since last seen,,+ - primary entry using vPC Peer-Link
(T) - True, (F) - False, h - hex, d - decimal
VDC = 3
FE VLAN/BD MAC Address Type Age Secure NTFY Ports/SWID.SSID.LID(d)
-----+------+-------------+--------+------+------+------+-----------------------
* 1 10 e4c7.2210.a142 dynamic 360 F F Po1
確定埠通道1上用於從N7K2向Sup轉發流量的鏈路，以及當埠通道1從N7K1向N7K2使用時用於從N7K3傳送回覆的鏈路：
N7K2# show port-channel load-balance forwarding-path interface port-channel 1 src-ip
192.168.12.2 dst-ip 192.168.13.3 module 3
Module 3: Missing params will be substituted by 0's.
Load-balance Algorithm: src-dst ip
RBH: 0xd2 Outgoing port id: Ethernet3/3
N7K1# show port-channel load-balance forwarding-path interface port-channel 1 src-ip
192.168.13.3 dst-ip 192.168.12.2 module 3
Module 3: Missing params will be substituted by 0's.
Load-balance Algorithm: src-dst ip
RBH: 0xd2 Outgoing port id: Ethernet3/1
從N7K2（IP地址192.168.12.2）傳送ping命令，並在入口方向上捕獲N7K1上的資料包，以確認資料包是否已轉發到N7K3（IP地址192.168.13.3）。
傳送ping之前，您應該知道硬體堆積。完成以下步驟即可瞭解累積：
- 連線模組：
N7K1# attach module 3
Attaching to module 3 ...
To exit type 'exit', to abort type '$.' - 找出側翼的實例。側翼是用於F3系列模組的晶片交換(SOC)ASIC。每個側翼對映到模組上的兩個外部埠（資訊因模組型別而改變，且特定於N7K-F312FQ-25）。
模組上有12個埠，每個ASIC對映到前面板上的兩個埠，這意味著模組上有6個(0-5)側翼例項（例項計數基於零）。附註：開始之前，請確保您具有網路管理許可權。
捕獲通過N7K1上的埠通道1從N7K2到達的資料包時，請查詢對映到每個例項的埠（e3/1和e3/2）：
module-3# show hardware internal dev-port-map
--------------------------------------------------------------
CARD_TYPE: 12 port 40G
>Front Panel ports:12
--------------------------------------------------------------
Device name Dev role Abbr num_inst:
--------------------------------------------------------------
> Flanker Eth Mac Driver DEV_ETHERNET_MAC MAC_0 6
> Flanker Fwd Driver DEV_LAYER_2_LOOKUP L2LKP 6
!--- Check for the L2LKP number for ports 1 and 2.
> Flanker Xbar Driver DEV_XBAR_INTF XBAR_INTF 6
> Flanker Queue Driver DEV_QUEUEING QUEUE 6
> Sacramento Xbar ASIC DEV_SWITCH_FABRIC SWICHF 1
> Flanker L3 Driver DEV_LAYER_3_LOOKUP L3LKP 6
> EDC DEV_PHY PHYS 2
+-----------------------------------------------------------------------+
+----------------+++FRONT PANEL PORT TO ASIC INSTANCE MAP+++------------+
+-----------------------------------------------------------------------+
FP port | PHYS | MAC_0 | L2LKP | L3LKP | QUEUE |SWICHF
1 0 0 0 0 0
!--- The L2KLP for both ports is 0, so both belong to instance 0.
2 0 0 0 0 0
3 1 1 1 1 0
4 1 1 1 1 0
5 0 2 2 2 2 0
6 0 2 2 2 2 0
7 1 3 3 3 3 0
8 1 3 3 3 3 0
9 4 4 4 4 0
10 4 4 4 4 0
11 5 5 5 5 0
12 5 5 5 5 0
+-----------------------------------------------------------------------+
+-----------------------------------------------------------------------+ - 選擇例項，設定觸發器，然後開始捕獲。但是，必須瞭解，有許多選項可用於ELAM觸發器：
module-3# elam asic flanker instance 0
如果要在捕獲（交換機接收的資料包）中包括DBUS，這兩個選項非常重要。 這是未經查詢的原始資料包。RBUS顯示DBUS硬體中的查詢結果。要獲得完整的ELAM和分析，必須捕獲RBUS和DBUS。
module-3(fln-elam)# layer2
module-3(fln-l2-elam)# trigger ?
dbus Pre L2 BUS
rbus Post L2 BUS
-----SNIP-----
下一個輸出顯示可以使用DBUS選項捕獲的資料包型別。在此範例中，已選擇Internet通訊協定第4版(IPv4)封包：
module-3(fln-l2-elam)# trigger dbus ?
以下是您可以選擇使用的一些其他選項：
arp ARP Frame Format
fc Fc hdr Frame Format
ipv4 IPV4 Frame Format
ipv6 IPV6 Frame Format
mpls MPLS
other L2 hdr Frame Format
pup PUP Frame Format
rarp RARP Frame Format
valid On valid packet
module-3(fln-l2-elam)# trigger dbus ipv4 ?
在本示例中，使用if控制代碼為捕獲選擇條件。下一個輸出中顯示的多數選項基於L2、L3和L4報頭。源IP地址和目的IP地址也用於捕獲。
egress Egress packets
!--- Capture packets in egress (outbound from the port).
if If Trigger Condition
ingress Ingress packets
!--- Capture packets in ingress (inbound to the port).
multicast Multicast packet
multicast-replication Multicast replication
module-3(fln-l2-elam)# trigger dbus ipv4 ingress if ?
此輸出顯示了最終的觸發器選項：
<CR>
acos Acos
block-capture Capture l2 blocks
bpdu Bpdu
bundle-port Bundle-port
ccc Ccc
copp Copp
da-type Da-type
de-cfi De cfi
destination-index Destination-index
destination-ipv4-address destination ipv4 address
destination-mac-address Destination-mac-address
destination-vif Destination-vif
df df
dfst Dfst
dft Dft
disable-index-learn Disable-index-learn
disable-new-learn Disable-new-learn
dont-forward Dont-forward
dont-learn Dont-learn
dtag-ftag Dtag-ftag
dtag-ttl Dtag-ttl
dti-type-vpnid Dti type vpnid
error Error
erspan-kpa-valid Erspan kpa valid
ff Ff
frag frag
header-type Header type
ib-length-bundle Ib length bundle
ids-check-fail Ids-check-fail
ignore-acli Ignore-acli
ignore-aclo Ignore-aclo
ignore-qosi Ignore-qosi
ignore-qoso Ignore-qoso
inband-flow-creation-deletion Inband-flow-creation-deletion
index-direct Index-direct
inner-cos Inner-cos
inner-de-valid Inner de valid
inner-drop-eligibility Inner-drop-eligibility
ip-da-multicast Ip-da-multicast
ip-multicast Ip-multicast
ip-multicast-control Ip-multicast-control
ipv6 Ipv6
l2 L2
l2-frame-type L2-frame-type
l2-length-check L2 length check
l2lu-mode L2lu-mode
l3-packet-length l3 packet length
l4-protocol l4 protocol
label-count Label count
last-ethertype Last-ethertype
lbl0-eos Lbl0 eos
lbl0-exp Lbl0 exp
lbl0-lbl Lbl0 lbl
lbl0-ttl Lbl0 ttl
lbl0-valid Lbl0 valid
lbl1-exp Lbl1 exp
lbl1-ttl Lbl1 ttl
mac-in-mac-valid Mac-in-mac-valid
mc Mc
md-acos Md acos
md-destination-table-index Md destination table index
md-fwd-only Md fwd only
md-lif Md lif
md-mark-enable Md mark enable
md-multicast-bridge-disable Md multicast bridge disable
md-preserve-acos Md preserve acos
md-qos-group-id Md qos group id
md-replication-packet Md replication packet
md-router-mac Md router mac
md-ttl-err Md-ttl-err
md-version Md version
mf mf
mim-destination-mac-address Mim-destination-mac-address
mim-source-mac-address Mim-source-mac-address
mlh-type Mlh-type
no-stats No-stats
notify-index-learn Notify-index-learn
notify-new-learn Notify-new-learn
null-label-exp Null label exp
null-label-ttl Null label ttl
null-label-valid Null label valid
option option
outer-cos Outer-cos
outer-drop-eligibility Outer-drop-eligibility
ovl-mlh-bndl Ovl mlh bndl
ovl-ulh-bndl Ovl ulh bndl
ovl-ulh-bndl-1 Ovl-ulh-bndl-1
ovl-ulh-bndl-2 Ovl-ulh-bndl-2
packet-length Packet-length
packet-type Packet type
pdt-tag-gt-2 Pdt-tag-gt-2
pdt-tag0 Pdt-tag0
pdt-tag1 Pdt-tag1
pdt-valid Pdt-valid
pdt-value Pdt-value
port-id Port-id
rbh Rbh
rdt Rdt
recir-shim-vxlan-src-peer-id Recir shim vxlan src peer id
recirc-acos Recirc acos
recirc-bypass-ife Recirc bypass ife
recirc-bypass-l2 Recirc bypass l2
recirc-destination-table-index Recirc destination table index
recirc-forward-only Recirc forward only
recirc-l2-tunnel-encap Recirc l2 tunnel encap
recirc-lif Recirc lif
recirc-ls-hash Recirc ls hash
recirc-mark-enable Recirc mark enable
recirc-multicast-bridge-disable Recirc multicast bridge disable
recirc-preserve-acos Recirc preserve acos
recirc-preserve-ls-hash Recirc preserve ls hash
recirc-preserve-rbh Recirc preserve rbh
recirc-qos-group-id Recirc qos group id
recirc-replication-packet Recirc replication packet
recirc-router-mac Recirc router mac
recirc-ttl-err Recirc ttl err
recirc-valid Recirc-valid
recirc-version Recirc version
redirect Redirect
repl-bypass-ife Repl bypass ife
repl-bypass-l2 Repl bypass l2
repl-disable-local-bridge Repl disable local bridge
repl-fwd-only Repl fwd only
repl-l2-tunnel-encap Repl l2 tunnel encap
repl-l2-tunnel-info Repl l2 tunnel info
repl-lif Repl lif
repl-mark-enable Repl mark enable
repl-met-lif Repl met lif
repl-ml3 Repl ml3
repl-preserve-acos Repl preserve acos
repl-preserve-rbh Repl preserve rbh
repl-qos-group-id Repl qos group id
repl-replication-packet Repl replication packet
repl-router-mac Repl router mac
repl-ttl-err Repl ttl err
repl-version Repl version
rf Rf
second-inner-cos Second inner cos
segment-id Segment id
segment-id-valid Segment id valid
sequence-number Sequence-number
sg-tag Sg-tag
shim-valid Shim valid
source-index Source-index
source-ipv4-address source ipv4 address
source-mac-address Source-mac-address
source-vif Source-vif
status-ce-1q Status-ce-1q
status-is-1q Status-is-1q
sup-eid Sup-eid
tos tos
traceroute Traceroute
trig Any of previous elam triggered
trill-encap Trill-encap
ttl ttl
tunnel-bundle Tunnel bundle
tunnel-type Tunnel type
ulh-type Ulh-type
valid VALID
vl Vl
vlan Vlan
vn-p Vn p
vn-valid Vn-valid
vqi Vqi
vqi-valid Vqi-valid
vsl-num Vsl-num
module-3# elam asic flanker instance 0
module-3(fln-elam)# layer2
module-3(fln-l2-elam)# trigger dbus ipv4 ingress if source-ipv4-address 192.168.12.2
destination-ipv4-address 192.168.13.3
module-3(fln-l2-elam)# trigger rbus ingress if trig附註：RBUS配置通常不複雜且保持簡單。
- 若要檢查觸發器，請輸入status命令，啟動捕獲進程，然後啟動從N7K2到N7K3（192.168.12.1到192.168.13.3）的ping:
module-3(fln-l2-elam)# stat
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 ingress if
source-ipv4-address 192.168.12.2 destination-ipv4-address 192.168.13.3
L2 DBUS: Configured
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus ingress if trig
L2 RBUS: Configured
module-3(fln-l2-elam)# start
module-3(fln-l2-elam)# status
!--- The status shows as Armed because the process has begun.
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 ingress if
source-ipv4-address 192.168.12.2 destination-ipv4-address 192.168.13.1
L2 DBUS: Armed
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus ingress if trig
L2 RBUS: Armed
module-3(fln-l2-elam)#
module-3(fln-l2-elam)# status
!--- If the packet is captured, the status shows Triggered.
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 ingress if
source-ipv4-address 192.168.12.2 destination-ipv4-address 192.168.13.3
L2 DBUS: Triggered
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus ingress if trig
L2 RBUS: Triggered
module-3(fln-l2-elam)# - 如果狀態顯示Triggered，請確認RBUS和DBUS是否具有相同的序列號，以確認它們用於相同的包。在本示例中，使用了0x55，但顯示序列號的列不同：
module-3(fln-l2-elam)# show dbus | in seq
sequence-number : 0x6b vl : 0x0
!--- The sequence number is the same (0x6b).
module-3(fln-l2-elam)# show rbus | in seq
l2-rbus-trigger : 0x1 sequence-number : 0x6b - 輸入show dbus和show rbus命令以驗證DBUS和RBUS。在DBUS命令輸出中查詢源索引，在RBUS命令輸出中查詢destination index:
module-3(fln-l2-elam)# show dbus
cp = 0x1007db4c, buf = 0x1007db4c, end = 0x10089e9c
--------------------------------------------------------------------
Flanker Instance 00 - Capture Buffer On L2 DBUS:
Status(0x0102), TriggerWord(0x000), SampleStored(0x005),CaptureBufferPointer(0x005)
is_l2_egress: 0x0000, data_size: 0x023
[000]: 5902a000 08010000 00000000 0cc01400 00145800 00000000 01800100 00000000
00000000 00000000 003931c8 842850b9 31c88428 50c00000 01ac0000 00000000 00000000
00000000 00000000 00000000 00000005 80005000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00605406 01605406 8180008f f0054608 00000000
Printing packet 0
--------------------------------------------------------------------
L2 DBUS PRS MLH IPV4
--------------------------------------------------------------------
label-count : 0x0 mc : 0x0
null-label-valid : 0x0 null-label-exp : 0x0
null-label-ttl : 0x0 lbl0-vld : 0x0
lbl0-eos : 0x0 lbl0-lbl : 0x0
lbl0-exp : 0x0 lbl0-ttl : 0x0
lbl1-exp : 0x0 lbl1-ttl : 0x0
ipv4 : 0x0 ipv6 : 0x0
l4-protocol : 0x1 df : 0x0
mf : 0x0 frag : 0x0
ttl : 0xff l3-packet-length : 0x54
option : 0x0 tos : 0x0
sup-eid : 0x0 header-type : 0x1
error : 0x0 redirect : 0x0
port-id : 0x0 last-ethertype : 0x800
l2-frame-type : 0x0 da-type : 0x0
packet-type : 0x0 l2-length-check : 0x0
ip-da-multicast : 0x0 ip-multicast : 0x0
ip-multicast-control: 0x0 ids-check-fail : 0x0
traceroute : 0x0 outer-cos : 0x0
inner-cos : 0x0 vqi-valid : 0x0
vqi : 0x0 packet-length : 0x66
vlan : 0xa destination-index : 0x0
source-index : 0xa2c bundle-port : 0x0
acos : 0x0 outer-drop-eligibility: 0x0
inner-drop-eligibility: 0x0 sg-tag : 0x0
rbh : 0x0 vsl-num : 0x0
inband-flow-creation-deletion: 0x0 ignore-qoso : 0x0
ignore-qosi : 0x0 ignore-aclo : 0x0
ignore-acli : 0x0 index-direct : 0x0
no-stats : 0x0 dont-forward : 0x0
notify-index-learn : 0x1 notify-new-learn : 0x1
disable-new-learn : 0x0 disable-index-learn : 0x0
dont-learn : 0x0 bpdu : 0x0
ff : 0x0 rf : 0x0
ccc : 0x0 l2 : 0x0
rdt : 0x0 dft : 0x0
dfst : 0x0 status-ce-1q : 0x0
status-is-1q : 0x1 trill-encap : 0x0
mim-valid : 0x0 dtag-ttl : 0x0
dtag-ftag : 0x0 valid : 0x1
erspan-kpa-valid : 0x0 recir-shim-vxlan-src-peer-id: 0x0
vn-valid : 0x0 source-vif : 0x0
destination-vif : 0x0 vn-p : 0x0
sequence-number : 0x6b vl : 0x0
inner-de-valid : 0x0 de-cfi : 0x0
second-inner-cos : 0x0 tunnel-type : 0x0
shim-valid : 0x0
segment-id-valid : 0x0 copp : 0x0
dti-type-vpnid : 0x0 segment-id : 0x0
ib-length-bundle : 0x58000 mlh-type : 0x5
ulh-type : 0x6
source-ipv4-address: 192.168.12.2
destination-ipv4-address: 192.168.13.3
mim-destination-mac-address : 0000.0000.0000
mim-source-mac-address : 0000.0000.0000
destination-mac-address : e4c7.2210.a142
source-mac-address : e4c7.2210.a143
module-3(fln-l2-elam)# show rbus
cp = 0x100a2548, buf = 0x100a2548, end = 0x100ae898
--------------------------------------------------------------------
Flanker Instance 00 - Capture Buffer On L2 RBUS:
Status(0x0102), TriggerWord(0x000), SampleStored(0x005),CaptureBufferPointer(0x005)
is_l2_egress: 0x0000, data_size: 0x018
[000]: 0059d930 0000000c c0000000 03580000 00000000 00000000 0000001f 57b00021
fdfc0000 00000000 02000000 14001402 8b000105 00000000 68200000 00000000 00000000
00000400 00008000 005b0000 00fe0e4c 7220850a 210000a0 000000b6
Printing packet 0
--------------------------------------------------------------------
L2 RBUS INGRESS CONTENT
--------------------------------------------------------------------
pad : 0x16764 valid : 0x1
l2-rbus-trigger : 0x1 sequence-number : 0x6b
rit-ipv4-id : 0x0 ipv4-tunnel-encap : 0x0
rit-mpls-rw : 0x0 ml2-ptr : 0x0
ml3-ptr : 0x0 mark : 0x0
result-cap3 : 0x0 di1-v5-delta-length : 0x0
di1-v5-delta-length-plus: 0x0 di1-v4-delta-length : 0x0
di1-v4-delta-length-plus: 0x0 di2-delta-length : 0x0
di2-delta-length-plus: 0x0 ml2-delta-length : 0x0
ml2-delta-length-plus: 0x0 ml3-delta-length : 0x0
ml3-delta-length-plus: 0x0 s-vector : 0x0
lcpu-ff-valid : 0x0 sup-di-vqi : 0x0
erspan-term-index-dir: 0x0 erspan-buffer-check : 0x0
l2-tunnel-decapped : 0x0 l3-delta-length : 0x0
rit-crc16-valid : 0x1 rit-crc16 : 0xf57b
vntag-p : 0x0 frr-recirc : 0x0
ingress-lif : 0x1 earl-proxy-vld : 0x0
md-di-vld : 0x0 rc : 0x0
segment-id-valid : 0x0 ttl-out : 0xfe
ttl-mid : 0xfe tos-out : 0x0
tos-in : 0x0 orig-vlan1 : 0x0
vlan1 : 0x0 source-peer-id : 0x0
final-ignore-qoso : 0x0 port-id : 0x0
cr-type : 0x1 pup-packet : 0x0
bpdu : 0x0 vdc : 0x0
traceroute : 0x0 de : 0x0
cos : 0x0 inner-drop-eligibility: 0x0
inner-cos : 0x0 acos : 0x0
di-ltl-index : 0x50 l3-multicast-di : 0x50
source-index : 0xa2c vlan : 0x0
index-direct : 0x0 di1-valid : 0x1
vqi : 0x50 di2-valid : 0x0
v5-fpoe-idx : 0x0 di2-fpoe-idx : 0x0
l3-multicast-v5 : 0x0 dft : 0x0
dfst : 0x0 l3-learning-ff : 0x0
result-rbh : 0xd0 di2-cr-type : 0x0
result-2 : 0x1 dtag-ftag : 0x0
dtag-ttl : 0x20 mac-in-mac-op : 0x0
dvif : 0x0 result-cap1 : 0x0
result-cap2 : 0x0 erspan-term : 0x0
erspan-decap : 0x0 dont-learn : 0x0
routed-frame : 0x1 copy-cause : 0x0
l2-copy-cause : 0x0 l3-rit-ptr : 0x5b
sg-tag : 0x0 trill-nh-id : 0x0
ttl-in : 0xfe fc-up : 0x0
up-did : 0x0 did : 0xe4c722
up-sid : 0x0 sid : 0x10a144
shim-l2-tunnel-encap: 0x0 shim-ls-hash : 0x8
shim-rc : 0x0 shim-lif : 0x1
shim-replication-pkt: 0x0 shim-router-mac : 0x1
shim-mark-enable : 0x0 shim-qos-group-id : 0x0
shim-destination-table-index: 0x5b shim-acos-preserve : 0x0
mim-destination-mac-address : 0000.0000.0000
mim-source-mac-address : 0000.0000.0000 - 檢查Sup：上的目標索引和源索引
N7K1# show system internal pixm info ltl 0xa2c
此輸出確認資料包是在埠通道1(Po1)上收到並通過Eth3/5轉發。
PC_TYPE PORT LTL RES_ID LTL_FLAG CB_FLAG MEMB_CNT
------------------------------------------------------------------------------
Normal Po1 0x0a2c 0x16000000 0x00000000 0x00000002 2
Member rbh rbh_cnt
Eth3/2 0x000000f0 0x04
Eth3/1 0x0000000f 0x04
CBL Check States: Ingress: Enabled; Egress: Enabled
VLAN| BD| BD-St | CBL St & Direction:
--------------------------------------------------
1 | 0x15 | INCLUDE_IF_IN_BD | FORWARDING (Both)
10 | 0x19 | INCLUDE_IF_IN_BD | FORWARDING (Both)
Member info
------------------
Type LTL
---------------------------------
PORT_CHANNEL Po1
FLOOD_W_FPOE 0x8019
FLOOD_W_FPOE 0x8015
N7K1# show system internal pixm info ltl 0x50
0x0050 is in DCE/FC pool
Member info
------------------
Type LTL
---------------------------------
PHY_PORT Eth3/5 - 驗證模組上的本地目標邏輯(LTL)是否正確程式設計：
module-3# show system internal pixmc info ltl-cb ltl 0xa2c
ltl |ltl_type|if_index|lc_type| vdc |v4_fpoe|v5_fpoe| base_fpoe_idx | flag
0x0a2c | 4 | Po1 | 2 | 2 | 0x00 | 0x00 | 0x0000 | 0x0
, local ports:
VDCs the entry is part of:
LTL HW programming info
.......................
----------------------------------------------------
|Index | ec |drop|span_vec|SOM|ucr_fab|
|--------------------------------------------------
|[ a2c]| 1| 0| 0| 0| 0|
| RBH | VQI | PS(INST:LPOE)
|----------------------------------
0, 40 0 : 1
1, 40 0 : 1
2, 40 0 : 1
3, 40 0 : 1
4, 44 0 : 10
5, 44 0 : 10
6, 44 0 : 10
7, 44 0 : 10
8, 0 0 : 1
9, 0 0 : 1
a, 0 0 : 1
b, 0 0 : 1
c, 0 0 : 10
d, 0 0 : 10
e, 0 0 : 10
f, 0 0 : 10
module-3# show system internal pixmc info ltl-cb ltl 0x50
ltl |ltl_type|if_index|lc_type| vdc |v4_fpoe | v5_fpoe| base_fpoe_idx | flag
0x0050 | 5 |Eth3/5 | 2 | 2 | 0x00 | 0x00 | 0x0000 | 0x0
, local ports:
VDCs the entry is part of:
LTL HW programming info
.......................
----------------------------------------------------
|Index | ec |drop|span_vec|SOM|ucr_fab|
|--------------------------------------------------
|[ 50]| 1| 0| 0| 0| 0|
| RBH | VQI | PS
|----------------------------
ALL RBH| 50 | 2 : 1 - 在輸出時捕獲ELAM資料包。為了擷取封包，請從IP位址192.168.13.3到192.168.12.2傳送ping回覆。您必須在連線埠通道1介面(e3/1-2)上使用egress關鍵字設定擷取。 介面屬於例項0（如前所述）。
N7K1# att mo 3
如圖所示，源和目標索引都是DBUS的一部分（與入口捕獲中所示不同）。
Attaching to module 3 ...
To exit type 'exit', to abort type '$.'
module-3# el asic flanker instance 0
module-3(fln-elam)# layer2
module-3(fln-l2-elam)# trigger dbus ipv4 egress if source-ipv4-address 192.168.13.3
destination-ipv4-address 192.168.12.2
module-3(fln-l2-elam)# trigger rbus egress if trig
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.13.3 destination-ipv4-address 192.168.12.2
L2 DBUS: Configured
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Configured
module-3(fln-l2-elam)# start
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.13.3 destination-ipv4-address 192.168.12.2
L2 DBUS: Armed
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Armed
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.13.3 destination-ipv4-address 192.168.12.2
L2 DBUS: Triggered
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Triggered
module-3(fln-l2-elam)#
module-3(fln-l2-elam)# show dbus | in seq
sequence-number : 0x8d vl : 0x3
!--- The sequence number is the same.
module-3(fln-l2-elam)# show rbus | in seq
vl : 0x0 sequence-number : 0x8d
module-3(fln-l2-elam)# show dbus
cp = 0x1007db4c, buf = 0x1007db4c, end = 0x10089e9c
--------------------------------------------------------------------
Flanker Instance 00 - Capture Buffer On L2 DBUS:
Status(0x0102), TriggerWord(0x000), SampleStored(0x005),CaptureBufferPointer(0x005)
is_l2_egress: 0x0000, data_size: 0x023
[000]: 48c22000 08210000 40020800 0cc01414 5800a000 00001a40 01030000 00000000
00000000 00000000 003931c8 842850f9 31c88428 50800000 02358000 00000000 00000000
00000000 00000000 00000000 00000000 00005000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00605406 81e05406 0100008f e0054600 00000000
Printing packet 0
--------------------------------------------------------------------
L2 DBUS PRS MLH IPV4
--------------------------------------------------------------------
label-count : 0x0 mc : 0x0
null-label-valid : 0x0 null-label-exp : 0x0
null-label-ttl : 0x0 lbl0-vld : 0x0
lbl0-eos : 0x0 lbl0-lbl : 0x0
lbl0-exp : 0x0 lbl0-ttl : 0x0
lbl1-exp : 0x0 lbl1-ttl : 0x0
ipv4 : 0x0 ipv6 : 0x0
l4-protocol : 0x1 df : 0x0
mf : 0x0 frag : 0x0
ttl : 0xfe l3-packet-length : 0x54
option : 0x0 tos : 0x0
sup-eid : 0x0 header-type : 0x1
error : 0x0 redirect : 0x0
port-id : 0x1 last-ethertype : 0x800
l2-frame-type : 0x0 da-type : 0x0
packet-type : 0x1 l2-length-check : 0x0
ip-da-multicast : 0x0 ip-multicast : 0x0
ip-multicast-control: 0x0 ids-check-fail : 0x0
traceroute : 0x0 outer-cos : 0x0
inner-cos : 0x0 vqi-valid : 0x1
vqi : 0x40 packet-length : 0x66
vlan : 0xa destination-index : 0xa2c
source-index : 0x50 bundle-port : 0x0
acos : 0x0 outer-drop-eligibility: 0x0
inner-drop-eligibility: 0x0 sg-tag : 0x0
rbh : 0xd2 vsl-num : 0x0
inband-flow-creation-deletion: 0x0 ignore-qoso : 0x0
ignore-qosi : 0x0 ignore-aclo : 0x0
ignore-acli : 0x0 index-direct : 0x0
no-stats : 0x0 dont-forward : 0x0
notify-index-learn : 0x1 notify-new-learn : 0x0
disable-new-learn : 0x0 disable-index-learn : 0x0
dont-learn : 0x0 bpdu : 0x0
ff : 0x0 rf : 0x1
ccc : 0x4 l2 : 0x0
rdt : 0x0 dft : 0x0
dfst : 0x0 status-ce-1q : 0x0
status-is-1q : 0x0 trill-encap : 0x0
mim-valid : 0x0 dtag-ttl : 0x0
dtag-ftag : 0x0 valid : 0x1
erspan-kpa-valid : 0x0 recir-shim-vxlan-src-peer-id: 0x0
vn-valid : 0x0 source-vif : 0x0
destination-vif : 0x0 vn-p : 0x0
sequence-number : 0x8d vl : 0x3
inner-de-valid : 0x0 de-cfi : 0x0
second-inner-cos : 0x0 tunnel-type : 0x0
shim-valid : 0x0
segment-id-valid : 0x0 copp : 0x0
dti-type-vpnid : 0x0 segment-id : 0x0
ib-length-bundle : 0x0 mlh-type : 0x5
ulh-type : 0x6
source-ipv4-address: 192.168.13.3
destination-ipv4-address: 192.168.12.2
mim-destination-mac-address : 0000.0000.0000
mim-source-mac-address : 0000.0000.0000
destination-mac-address : e4c7.2210.a143
source-mac-address : e4c7.2210.a142
module-3(fln-l2-elam)# show rbus
源和目的IP地址正確，在入口ELAM資料包捕獲後解碼；但是，與輸入ELAM相比，方向肯定相反，因為會擷取回傳流量。
cp = 0x100a2548, buf = 0x100a2548, end = 0x100ae898
--------------------------------------------------------------------
Flanker Instance 00 - Capture Buffer On L2 RBUS:
Status(0x1102), TriggerWord(0x000), SampleStored(0x008),CaptureBufferPointer(0x000)
is_l2_egress: 0x0001, data_size: 0x018
[000]: 0048ea00 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 0c000000 00000000 04014008 00005000 00000000
00000726 3910850a 1b931c88 42850800 00000000 00000000 0000008d
Printing packet 0
--------------------------------------------------------------------
L2 RBUS EGRESS CONTENT
--------------------------------------------------------------------
pad : 0x0 valid : 0x1
trig : 0x1 reserved : 0x0
vn-tag-p : 0x0 cbl-vlan-valid : 0x0
vft-hop-count : 0x0 vft-vsan : 0x0
vft-up : 0x0 vft-valid : 0x0
copp : 0x0 segment-id-valid : 0x0
segment-id-23 : 0x0 vsl-num : 0x0
inner-cos : 0x0 inner-drop-eligibility: 0x0
cos : 0x0 drop-eligibility : 0x0
dce-mode : 0x0 flood-to-bd : 0x0
pt-bit-en : 0x1 cpu-port : 0x0
vlan-id : 0xa ip-tos : 0x0
result-rbh : 0x1 met-ptr : 0x2000
packet-type : 0x1 sg-tag : 0x0
dtag-ftag : 0x0 vdc : 0x0
vn-tag-src-vif : 0x0 vn-tag-dst-vif : 0x0
vn-tag-l : 0x0 dc3-tr : 0x0
vl : 0x0 sequence-number : 0x8d
destination-mac-valid: 0x0
source-mac-valid: 0x0
mim-destination-mac-address : 0000.0000.0000
destination-mac-address : e4c7.2210.a143
source-mac-address : e4c7.2210.a142
mim-source-mac-address : 0000.0000.0000 - 檢查N7K1上埠通道1的模組3的基於顏色的邏輯(CBL)，以確定VLAN 10是否通過它轉發流量。CBL是基於每個物理介面的邏輯，因此您應該輸入N7K1上埠通道1的成員介面號，而不是埠通道號。在下一個輸出中，可以看到VLAN 10按照預期轉發它。
CBL用於確定硬體中埠的生成樹協定(STP)狀態。檢查Sup上VLAN的STP時，介面可能會顯示轉送，但模組會封鎖流量。附註：必須分別檢查兩個成員介面（e3/1和e3/2）的CBL。
module-3# show hardware internal mac port 1 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-9,11-4031,4036-4095 |
| Forwarding State | 1,10,4032-4035 |
| Blocked State | |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-9,11-4031,4036-4095 |
| Forwarding State | 1,10,4032-4035 |
| Blocked State | |
| Learning State | |
--------------------------------------------------------------------------------附註：上一個命令用於埠通道1(模組3位於e3/1上)。
module-3# show hardware internal mac port 2 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-9,11-4031,4036-4095 |
| Forwarding State | 1,10,4032-4035 |
| Blocked State | |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-9,11-4031,4036-4095 |
| Forwarding State | 1,10,4032-4035 |
| Blocked State | |
| Learning State | |
--------------------------------------------------------------------------------附註：同樣，此命令檢查連線埠通道2(e3/2)的CBL。
使用分支電纜排除F3系列模組上的ELAM故障
連線分支電纜時，F3系列模組的ELAM過程與常規模組埠上的ELAM過程沒有區別。但是，在嘗試將索引轉換為前面板編號期間，連線埠索引管理員(PIXM)的驗證有一些變更，在這種情況下，介面會從分支纜線接收。
本節中的示例使用的拓撲如下：
+------------+ BreakOut Cable +-----------+
| | e3/8/1-4 te1/1| |
| | +-----------+ |
| |e3/8 | 1/2 | 4500-X |
| N7K3 +----------------------+ |
| | Po2 | 1/3 | |
| | +-----------+ |
| | | 1/4 | |
+------------+ +-----------+-----------+
Vlan20 SVI Vlan20 SVI
IP add 192.168.20.3 IP add 192.168.20.1
在本例中，一根分支電纜連線到乙太網介面3/8，該介面將40千兆埠分為四個10千兆埠。本節提供了所需的配置以供參考。
N7K3(config)# interface breakout module 3 port 8 map 10g-4x
N7K3(config)# show interface brief
---SNIP---
---------------------------------------------------------------
Ethernet VLAN Type Mode Status Reason Speed Port
Interface Ch #
---------------------------------------------------------------
Eth3/7 -- eth routed up none 40G(D) --
Eth3/8/1 1 eth trunk up none 10G(D) 2
!--- From 3/8/1 to 3/8/4.
Eth3/8/2 1 eth trunk up none 10G(D) 2
Eth3/8/3 1 eth trunk up none 10G(D) 2
Eth3/8/4 1 eth trunk up none 10G(D) 2
在先前的輸出中，您可以看到Ethernet interface 3/7仍然是40 Gigabit連線埠；但是，Ethernet interface 3/8現在分為四個10-Gigabit連線埠，可以分別進行設定：
N7K3# show run interface e3/8/1 - 4
!Command: show running-config interface Ethernet3/8/1-4
!Time: Mon May 4 01:46:28 2015
version 6.2(8a)
interface Ethernet3/8/1
switchport
switchport mode trunk
switchport trunk allowed vlan 10,20
no shutdown
interface Ethernet3/8/2
switchport
switchport mode trunk
switchport trunk allowed vlan 30,40
no shutdown
interface Ethernet3/8/3
switchport
switchport mode trunk
switchport trunk allowed vlan 50
no shutdown
interface Ethernet3/8/4
switchport
switchport mode trunk
no shutdown
開始從N7K3交換虛擬介面(SVI)20 IP地址(192.168.20.3)到4500 SVI 20 IP地址(192.168.20.1)的資料包捕獲。 在出口到4500時，資料包將在N7K3上捕獲，並將應答從4500傳送到N7K3。
如上一節所述，必須瞭解Flanker例項才能應用觸發器。此輸出顯示了模組3的附件：
N7K3# attach module 3
Attaching to module 3 ...
To exit type 'exit', to abort type '$.'
module-3# show hardware internal dev
dev-port-map dev-version
module-3# show hardware internal dev-port-map
--------------------------------------------------------------
CARD_TYPE: 12 port 40G
>Front Panel ports:12
--------------------------------------------------------------
Device name Dev role Abbr num_inst:
--------------------------------------------------------------
> Flanker Eth Mac Driver DEV_ETHERNET_MAC MAC_0 6
> Flanker Fwd Driver DEV_LAYER_2_LOOKUP L2LKP 6
> Flanker Xbar Driver DEV_XBAR_INTF XBAR_INTF 6
> Flanker Queue Driver DEV_QUEUEING QUEUE 6
> Sacramento Xbar ASIC DEV_SWITCH_FABRIC SWICHF 1
> Flanker L3 Driver DEV_LAYER_3_LOOKUP L3LKP 6
> EDC DEV_PHY PHYS 2
+-----------------------------------------------------------------------+
+----------------+++FRONT PANEL PORT TO ASIC INSTANCE MAP+++------------+
+-----------------------------------------------------------------------+
FP port | PHYS | MAC_0 | L2LKP | L3LKP | QUEUE |SWICHF
1 0 0 0 0 0
2 0 0 0 0 0
3 1 1 1 1 0
4 1 1 1 1 0
5 0 2 2 2 2 0
6 0 2 2 2 2 0
7 1 3 3 3 3 0
8 1 3 3 3 3 0
!--- The port 8 L2LKP column shows a value of 3.
9 4 4 4 4 0
10 4 4 4 4 0
11 5 5 5 5 0
12 5 5 5 5 0
+-----------------------------------------------------------------------+
+-----------------------------------------------------------------------+
在此輸出中，埠8位於flanker例項3上。現在您已瞭解該例項，可以通過源和目標IP地址放置觸發器。因為您將捕獲從N7K3到4500的ping請求，所以它將是一個出口ELAM。
module-3# elam asic flanker instance 3
module-3(fln-elam)# layer2
module-3(fln-l2-elam)# trigger dbus ipv4 egress if source-ipv4-address 192.168.20.3
destination-ipv4-address 192.168.20.1
module-3(fln-l2-elam)# trigger rbus egress if trig
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 3: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.20.3 destination-ipv4-address 192.168.20.1
L2 DBUS: Configured
ELAM Slot 3 instance 3: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Configured
module-3(fln-l2-elam)# start
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 3: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.20.3 destination-ipv4-address 192.168.20.1
L2 DBUS: Armed
ELAM Slot 3 instance 3: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Armed
從N7K3向4500發起ping:
N7K3# ping 192.168.20.1
PING 192.168.20.1 (192.168.20.1): 56 data bytes
36 bytes from 192.168.20.3: Destination Host Unreachable
Request 0 timed out
64 bytes from 192.168.20.1: icmp_seq=1 ttl=254 time=6.49 ms
64 bytes from 192.168.20.1: icmp_seq=2 ttl=254 time=6.518 ms
64 bytes from 192.168.20.1: icmp_seq=3 ttl=254 time=7.936 ms
64 bytes from 192.168.20.1: icmp_seq=4 ttl=254 time=7.945 ms
--- 192.168.20.1 ping statistics ---
5 packets transmitted, 4 packets received, 20.00% packet loss
round-trip min/avg/max = 6.49/7.222/7.945 ms
以下是ELAM狀態：
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 3: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.20.3 destination-ipv4-address 192.168.20.1
L2 DBUS: Triggered
ELAM Slot 3 instance 3: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Triggered
驗證序列號是否相同：
module-3(fln-l2-elam)# show dbus | in seq
sequence-number : 0x27 vl : 0x3
module-3(fln-l2-elam)# show rbus | in seq
vl : 0x0 sequence-number : 0x27
序列號相同。現在您可以檢查DBUS和RBUS資訊：
module-3(fln-l2-elam)# show dbus
cp = 0x1011033c, buf = 0x1011033c, end = 0x1011c68c
--------------------------------------------------------------------
Flanker Instance 03 - Capture Buffer On L2 DBUS:
Status(0x0102), TriggerWord(0x000), SampleStored(0x004),CaptureBufferPointer(0x004)
is_l2_egress: 0x0000, data_size: 0x023
[000]: 4c1ea000 20a10000 40021040 0cc02801 04080000 00000000 08100000 00000000
00000000 00000000 003c1fc1 8732dff9 31c88428 51000000 009d8000 00000000 00000000
00000000 00000000 00000000 00000000 00005000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 0060540a 01e0540a 0080008f f0054608 00000000
Printing packet 0
--------------------------------------------------------------------
L2 DBUS PRS MLH IPV4
--------------------------------------------------------------------
label-count : 0x0 mc : 0x0
null-label-valid : 0x0 null-label-exp : 0x0
null-label-ttl : 0x0 lbl0-vld : 0x0
lbl0-eos : 0x0 lbl0-lbl : 0x0
lbl0-exp : 0x0 lbl0-ttl : 0x0
lbl1-exp : 0x0 lbl1-ttl : 0x0
ipv4 : 0x0 ipv6 : 0x0
l4-protocol : 0x1 df : 0x0
mf : 0x0 frag : 0x0
ttl : 0xff l3-packet-length : 0x54
option : 0x0 tos : 0x0
sup-eid : 0x1 header-type : 0x0
error : 0x0 redirect : 0x0
port-id : 0x5 last-ethertype : 0x800
l2-frame-type : 0x0 da-type : 0x0
packet-type : 0x1 l2-length-check : 0x0
ip-da-multicast : 0x0 ip-multicast : 0x0
ip-multicast-control: 0x0 ids-check-fail : 0x0
traceroute : 0x0 outer-cos : 0x0
inner-cos : 0x0 vqi-valid : 0x1
vqi : 0x82 packet-length : 0x66
vlan : 0x14 destination-index : 0x82
source-index : 0x400 bundle-port : 0x0
acos : 0x0 outer-drop-eligibility: 0x0
inner-drop-eligibility: 0x0 sg-tag : 0x0
rbh : 0x0 vsl-num : 0x0
inband-flow-creation-deletion: 0x0 ignore-qoso : 0x0
ignore-qosi : 0x0 ignore-aclo : 0x0
ignore-acli : 0x0 index-direct : 0x1
no-stats : 0x0 dont-forward : 0x0
notify-index-learn : 0x0 notify-new-learn : 0x0
disable-new-learn : 0x0 disable-index-learn : 0x0
dont-learn : 0x1 bpdu : 0x0
ff : 0x0 rf : 0x0
ccc : 0x0 l2 : 0x0
rdt : 0x0 dft : 0x0
dfst : 0x0 status-ce-1q : 0x0
status-is-1q : 0x0 trill-encap : 0x0
mim-valid : 0x0 dtag-ttl : 0x0
dtag-ftag : 0x0 valid : 0x1
erspan-kpa-valid : 0x0 recir-shim-vxlan-src-peer-id: 0x0
vn-valid : 0x0 source-vif : 0x0
destination-vif : 0x0 vn-p : 0x0
sequence-number : 0x27 vl : 0x3
inner-de-valid : 0x0 de-cfi : 0x0
second-inner-cos : 0x0 tunnel-type : 0x0
shim-valid : 0x0
segment-id-valid : 0x0 copp : 0x0
dti-type-vpnid : 0x0 segment-id : 0x0
ib-length-bundle : 0x0 mlh-type : 0x5
ulh-type : 0x6
source-ipv4-address: 192.168.20.3
destination-ipv4-address: 192.168.20.1
mim-destination-mac-address : 0000.0000.0000
mim-source-mac-address : 0000.0000.0000
destination-mac-address : f07f.061c.cb7f
source-mac-address : e4c7.2210.a144
module-3(fln-l2-elam)#
module-3(fln-l2-elam)#
module-3(fln-l2-elam)#
module-3(fln-l2-elam)# show rbus
cp = 0x10134d38, buf = 0x10134d38, end = 0x10141088
--------------------------------------------------------------------
Flanker Instance 03 - Capture Buffer On L2 RBUS:
Status(0x1102), TriggerWord(0x000), SampleStored(0x008),CaptureBufferPointer(0x000)
is_l2_egress: 0x0001, data_size: 0x018
[000]: 004c4780 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 0c001000 00000000 80028010 00009000 00000000
00000783 f830e65b fb931c88 42851000 00000000 00000000 00000027
Printing packet 0
--------------------------------------------------------------------
L2 RBUS EGRESS CONTENT
--------------------------------------------------------------------
pad : 0x0 valid : 0x1
trig : 0x1 reserved : 0x0
vn-tag-p : 0x1 cbl-vlan-valid : 0x0
vft-hop-count : 0x0 vft-vsan : 0x0
vft-up : 0x0 vft-valid : 0x0
copp : 0x0 segment-id-valid : 0x0
segment-id-23 : 0x0 vsl-num : 0x0
inner-cos : 0x0 inner-drop-eligibility: 0x0
cos : 0x0 drop-eligibility : 0x0
dce-mode : 0x0 flood-to-bd : 0x0
pt-bit-en : 0x20 cpu-port : 0x0
vlan-id : 0x14 ip-tos : 0x0
result-rbh : 0x2 met-ptr : 0x4000
packet-type : 0x1 sg-tag : 0x0
dtag-ftag : 0x0 vdc : 0x0
vn-tag-src-vif : 0x0 vn-tag-dst-vif : 0x0
vn-tag-l : 0x0 dc3-tr : 0x0
vl : 0x0 sequence-number : 0x27
destination-mac-valid: 0x0
source-mac-valid: 0x0
mim-destination-mac-address : 0000.0000.0000
destination-mac-address : f07f.061c.cb7f
source-mac-address : e4c7.2210.a144
mim-source-mac-address : 0000.0000.0000
將目標和源索引轉換為前面板埠以確認流：
N7K3# show system internal pixm info ltl 0x400
0x0400 is in SUP In-band LTL range
此輸出顯示源索引。您知道這是正確的，因為從Sup向N7K3發出了ping。下一個輸出顯示了輸出介面(e3/8/1)，它是N7K上允許VLAN 20的兩個介面之一。另一個介面是e3/8/4,4500上由於STP而被阻止。
N7K3# show system internal pixm info ltl 0x82
0x0082 is in DCE/FC pool
Member info
------------------
Type LTL
---------------------------------
PHY_PORT Eth3/8/1
FLOOD_W_FPOE 0x8039
FLOOD_W_FPOE 0x803f
驗證已使用N7K上的分支電纜建立的埠的CBL。要檢查CBL，您必須擁有所有新形成的埠的硬體埠號。
附註：交換器上不存在介面e3/8。僅顯示新形成的埠。
N7K3# show interface e3/8
^
% Incomplete command at '^' marker.
N7K3#
由於使用了分支電纜並且交換機上不存在e3/8介面，因此用於獲取硬體埠號的計算方式會改變。對於支援分支的任何模組，硬體埠編號均不同。您應首先檢查連線埠是否支援中斷：
N7K3# show int e3/7 capabilities
Ethernet3/7
Model: N7K-F312FQ-25
Type (SFP capable): QSFP-40G-CR4
Speed: 10000,40000
Duplex: full
---SNIP---
PFC capable: yes
Breakout capable: yes
如圖所示，埠e3/7支援分支，這意味著其頻寬可以分為四個10千兆埠。類似地，具有100千兆埠的其他的F3系列模組可以分為十個埠，每個埠為10千兆位，或者三個埠為40千兆位，超額訂閱。這取決於模組。
由於本示例中的F3系列模組具有40千兆埠，且每個埠可分成四個埠，因此每個埠的硬體埠號在零基擴展上為0-3、4-7、8-11...40-43、44-47。第一個示例中的埠上有分支電纜，則其硬體埠編號將為0、1、2和3。如果沒有分支電纜，則其硬體埠編號將為0（1、2和3將處於活動狀態）。
由於父埠是e3/8，如果使用它時沒有分支電纜，則其硬體埠號為28；如果使用它與分支電纜，則硬體埠號為28、29、30和31。此命令輸出顯示活動的硬體埠（從零開始）：
N7K3# show system internal ifindex info mod 3
Init DB dump follows:
module_num_bitmask = 0x3ffff
Slot:3, Proc:1, breakout_factor:0, sw_card_id:0, active_cfg_ports:, broken_fp_po
rts:
Slot:3, Proc:2, breakout_factor:4, sw_card_id:155, active_cfg_ports:0,4,8,12,16,
20,24,28-32,36,40,44, broken_fp_ports:28
Lookup DB dump follows:
Slot:3, breakout_factor:4
斷開的埠硬體埠號為28，現在分為四個(28-32)。 現在您可以連線模組3並檢查硬體中的CBL:
N7K3# attach module 3
Attaching to module 3 ...
To exit type 'exit', to abort type '$.'
module-3#
F3系列模組要求根據基於一個的刻度格式化埠號。因此，您應該輸入29、30、31和32:
module-3# show hardware internal mac port ?
<1-96> Port number (1-based)
!--- This is context sensitive, so it helps to say the port number is 1-based.
以下是乙太網路介面3/8/1的執行組態，用於檢查並確認VLAN轉送狀態：
interface Ethernet3/8/1
switchport
switchport mode trunk
switchport trunk allowed vlan 10,20
no shutdown
module-3# show hardware internal mac port 29 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-9,11-19,21-4031,4036-4095 |
| Forwarding State | 10,20,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-9,11-19,21-4031,4036-4095 |
| Forwarding State | 10,20,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
以下是乙太網路介面3/8/2的執行組態，用於檢查並確認VLAN轉送狀態：
interface Ethernet3/8/2
switchport
switchport mode trunk
switchport trunk allowed vlan 30,40
no shutdown
module-3# show hardware internal mac port 30 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-29,31-39,41-4031,4036-4095 |
| Forwarding State | 30,40,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-29,31-39,41-4031,4036-4095 |
| Forwarding State | 30,40,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
以下是乙太網路介面3/8/3的執行組態，用於檢查並確認VLAN轉送狀態：
interface Ethernet3/8/3
switchport
switchport mode trunk
switchport trunk allowed vlan 50
no shutdown
module-3# show hardware internal mac port 31 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-49,51-4031,4036-4095 |
| Forwarding State | 50,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-49,51-4031,4036-4095 |
| Forwarding State | 50,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
以下是乙太網路介面3/8/4的執行組態，用於檢查並確認VLAN轉送狀態（允許所有已設定的VLAN）：
interface Ethernet3/8/4
switchport
switchport mode trunk
no shutdown
module-3# show hardware internal mac port 32 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-9,11-19,21-29,31-39,41-49,51-59,61-669,671-4031 |
| Disabled State | 4036-4095 |
| Forwarding State | 1,20,30,40,50,60,670,4032-4035 |
| Blocked State | 10 |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-9,11-19,21-29,31-39,41-49,51-59,61-669,671-4031 |
| Disabled State | 4036-4095 |
| Forwarding State | 1,20,30,40,50,60,670,4032-4035 |
| Blocked State | 10 |
| Learning State | |
--------------------------------------------------------------------------------
CBL顯示轉發的VLAN正確。
您可以使用show hardware internal error module <module number>命令獲取硬體埠號。當必須檢查未顯示在show interface x/y 命令輸出中的任何內部丟棄時，此命令非常有用。以下是範例：
N7K2# show hardware internal errors module 3
---SNIP---
Instance:1
Cntr Name Value Ports
----- ---- ----- -----
3836 igr rx pl: cbl drops 0000000000000001 10 -
4636 igr rx pl: cbl drops 0000000000000001 14 -
Instance:2
Cntr Name Value Ports
----- ---- ----- -----
423 igr in upm: pkts with symbol/sequence error rcvd 0000000000000478 18 -
455 igr in upm: pkts with symbol/sequence error rcvd 0000000000000478 17 -
487 igr in upm: pkts with symbol/sequence error rcvd 0000000000000478 19 -
519 igr in upm: pkts with symbol/sequence error rcvd 0000000000000478 20 -
Instance:3
Cntr Name Value Ports
----- ---- ----- -----
423 igr in upm: pkts with symbol/sequence error rcvd 0000000000000745 26 -
455 igr in upm: pkts with symbol/sequence error rcvd 0000000000000745 25 -
487 igr in upm: pkts with symbol/sequence error rcvd 0000000000000745 27 -
519 igr in upm: pkts with symbol/sequence error rcvd 0000000000000745 28 -
550 igr in upm: pkts rcvd, with RCODE violation 0000359810913821 30 -
551 igr in upm: pkts with symbol/sequence error rcvd 0000425092490108 30 -
552 igr in upm: pkts with error 0000000000176136 30 -
582 igr in upm: pkts rcvd, with RCODE violation 0000000000292641 29 -
583 igr in upm: pkts with symbol/sequence error rcvd 0000000000114014 29 -
614 igr in upm: pkts rcvd, with RCODE violation 0000133362265995 31 -
615 igr in upm: pkts with symbol/sequence error rcvd 0000146701474013 31 -
616 igr in upm: pkts with error 0000000000157479 31 -
646 igr in upm: pkts rcvd, with RCODE violation 0000000002160959 32 -
647 igr in upm: pkts with symbol/sequence error rcvd 0000000003722562 32 -
648 igr in upm: pkts with error 0000000000000002 32 -
由思科工程師貢獻
- Mohammed NijamuddinCisco TAC Engineer
意見