Cisco vWAAS Configuration Guide (for WAAS 6.4.1x)

VMware ESXi for Cisco vWAAS and Cisco WAAS

This section contains the following topics:

• VMware ESXi Versions Supported for Cisco WAAS
• ESXi Server Datastore Memory and Disk Space for vWAAS and vCM Models

VMware ESXi Versions Supported for Cisco WAAS

Table 4-2 VMware ESXi Versions Supported for Cisco WAAS

Note For vWAAS with ESXi Version 5.5 on a Cisco UCS host: if the DRE latency threshold or an AO timeout alarm occurs, check for the I/O command abort in the vWAAS. To do this, use the copy sysreport EXEC command.

If the I/O abort is observed:
Upgrade the RAID controller’s driver to Version 6.610.19.00 or later.

If the I/O abort is still observed after the RAID controller driver upgrade:
Capture and share the following logs for further analysis:
—Guest-VM sysreport
—VMware’s host diagnostic report
—RAID controller’s firmware log

ESXi Server Datastore Memory and Disk Space for vWAAS and vCM Models

This section contains the following topics:

• Table 4-3 shows ESXi server datastore memory and disk space per vWAAS model, for WAAS v4.3.1 through v5.3.5, and for WAAS v5.4.x through v6.x.
• Table 4-4 shows ESXi server datastore memory and disk space per vCM model, for WAAS v4.3.1 through v5.3.5, and for WAAS v5.4.x through v6.x.

Table 4-3 vCPUs, ESXi Server Datastore Memory, and Disk Space by vWAAS Model

Table 4-4 vCPUs, ESXi Server Datastore Memory, and Disk Space by vCM Model

OVA Package for vWAAS on VMware ESXi for WAAS Version 5.x to 6.2.x

For vWAAS on VMware ESXi, for WAAS Version 5.x through 6.2.x, Cisco provides an OVA or NPE OVA package for each vWAAS connection profile (examples shown in Table 4-5) and for each vCM connection profile (examples shown in Table 4-6).

Table 4-5 Cisco OVA Package Format Examples for vWAAS on VMware ESXi

Table 4-6 Cisco OVA Package Formats for vCM for WAAS Versions earlier than Version 6.4.1

OVA Package for vWAAS on VMware ESXi for WAAS Version 6.4.1 and Later

For vWAAS on VMware ESXi, for WAAS Version 6.4.1 and later, Cisco provides a single, unified OVA for NPE and non-NPE version of the WAAS image for all the vWAAS models for that hypervisor.

Each unified OVA package is a pre-configured virtual machine image that is ready to run on a particular hypervisor. The launch script for each unified OVA package file provides the model and other required parameters to launch vWAAS with WAAS in the required configuration.

Here are examples of the unified OVA and NPE OVA package filenames for vWAAS in VMware ESXi:

• OVA—Cisco-ESXi-vWAAS-Unified-6.4.1-b-33.ova
• NPE OVA—Cisco-ESXi-vWAAS-Unified-6.4.1-b-33-npe.ova

The unified OVA package for VMware ESXi contains the following files.

• OVF file—Contains all resource information.
• Flash disk image
• Data system disk
• Akamai disk

Use the VMware ESXi OVF template wizard to deploy these files, described in Installing VMware ESXi for vWAAS for WAAS Version 6.4.1 and Later.

Installing VMware ESXi for vWAAS for WAAS Versions 5.x to 6.2.x

To install the vWAAS Virtual Machine (VM) with VMware vSphere ESXi, follow these steps:

Step 1 From the vSphere Client, choose File > Deploy OVF Template.

The Source window appears (Figure 4-1).

Figure 4-1 vWAAS - Deploy OVF Template

Step 2 Click Browse.

The Open window appears.

Step 3 Navigate to the location of the vWAAS OVA file and click Open.

• If the virtual host was created using an OVA of vWAAS for WAAS Version 5.1.x or later, proceed to Step 4.
• If the virtual host was created using an OVA file of vWAAS for WAAS Version 5.0 or earlier, and you have upgraded vWAAS from inside WAAS, you must verify that the SCSI Controller Type is set to VMware Paravirtual. Otherwise, vWAAS will boot with no disk available, and will fail to load the specified configuration.

If needed, change the SCSI controller type to VMware Paravirtual by following these steps:

a. Power down the vWAAS.

b. From the VMware vCenter, navigate to vSphere Client > Edit Settings > Hardware.

c. Choose SCSI controller 0.

d. From the Change Type drop-down list, verify that the SCSI Controller Type is set to VMware Paravirtual. If this is not the case, choose VMware Paravirtual.

e. Click OK.

f. Power up the vWAAS, with WAAS Version 6.1.x or later.

Step 4 Click Next to accept the selected OVA file.

The Name and Location window appears.

Step 5 Enter a name for the vWAAS VM, choose the appropriate data center, and then click Next.

The Cluster window appears (if a cluster is configured), or the Resource Pool window appears (if a resource pool is configured). Otherwise, the Datastore window appears (in this case, skip to Step 7).

Figure 4-2 vWAAS - Name and Data Center Location

Step 6 If configured, choose a cluster for the vWAAS VM or, if configured, choose the resource pool and then click Next.

The Datastore window appears.

Step 7 Choose a datastore to host the virtual machine and click Next.

Figure 4-3 vWAAS - Datastore

Note The datastore must be formatted with a block size greater than 1 MB to support file sizes larger than 256 GB.

The Create a Disk window appears.

Step 8 The Disk Provisioning section has three disk format options: Thick Provision Lazy Zeroed, Thick Provision Eager Zeroed, and Thin Provision. Select Thick Provision Eager Zeroed.

Note You must choose the Thick Provision Eager Zeroed disk format for vWAAS deployment; this is the format recommended with vWAAS deployment for a clean installation.

Step 9 Click Next.

The Network Mapping window appears.

Step 10 Choose the network mapping provided by ESXi and click Next. You have the option to change this later if necessary.

The Ready to Complete window appears.

Figure 4-4 vWAAS - Network Mapping

Step 11 Click Finish to complete the installation.

The status window appears while the OVA file is being deployed.

Figure 4-5 vWAAS - Status Window

Step 12 When the deployment is finished, the Deployment Completed Successfully window appears.

Figure 4-6 vWAAS - Completed

Step 13 Click Close.

Step 14 You are ready to start the VM. Highlight the vWAAS VM and click Power on Virtual Machine.

Step 15 After vWAAS finishes booting, click the Console tab to view boot up messages.

Figure 4-7 vWAAS - Console

Note Under rare conditions, the vWAAS VM may boot into diskless mode if other VMs on the host VM server do not release control of system resources or the physical disks become unresponsive. For information on how to resolve this situation, see Resolving Diskless Startup and Disk Failure in Chapter 10, “Troubleshooting Cisco vWAAS.”

For vWAAS configuration information, see Chapter 2, “Configuring Cisco vWAAS and Viewing vWAAS Components” .

Installing VMware ESXi for vWAAS for WAAS Version 6.4.1 and Later

vWAAS for WAAS Version 6.4.1 and later supports VMware vCenter Version 6.0.0. To deploy any vWAAS or vCM Model for WAAS Version 6.4.1 and later on VMware ESXi, register the ESXi host with VMware vSphere vCenter version 6.0.

Note The OVA deployment for WAAS Version 6.4.1 and later must be done only through VMware vCenter.

To deploy the VMware ESXi hypervisor for vWAAS for WAAS Version 6.4.1 and later, follow these steps:

Step 1 Log in into the VMware vCenter using VMware vSphere Client (Figure 4-8).

Figure 4-8 VMware vSphere Client Login Window

Step 2 To begin the task of adding the ESXi host into the datacenter on VMware vCenter Client, you must first create a datacenter. Navigate to Actions > New Datacenter....

Step 3 At the Create Datacenter page, click Add.

Step 4 In the Create Datacenter dialog box:

a. In the Name field enter a name for the datacenter. The name can contain up to 16 alphanumeric characters with no spaces and no special characters.

b. In the Description field enter a description for this datacenter.

Step 5 To add the host into the datacenter on VMware vCenter Client, navigate to the Getting Started tab > Add Host... menu selection (Figure 4-9).

Figure 4-9 Add Host... Menu Selection

Step 6 Choose Specify Connection Settings and the Specify Connection Settings window appears (Figure 4-10).

Figure 4-10 Specify Connection Settings Window

a. In the Connection pane Host field, enter the ESXi host name or IP address.

b. In the Authorization pane Username and Password fields, enter the ESXi username and password.

c. Click Next.

Step 7 The Host Information window appears (Figure 4-11), which displays information you can review for the specified host, including host name or IP address, vendor name, model name and number, the VMware version, and the associated virtual machines.

Figure 4-11 Host Information Window

a. If the displayed host information meets your system requirements, click Next.

Step 8 The Assign License window appears.

There are two options: Assign an existing license key to this host and Assign a new license key to this host.

a. Use one of the radio buttons to assign an existing license key or to assign a new license key to this host.

b. Click Next.

Note Licenses are installed and managed only on individual devices, not device groups. For more information about licenses, see the “Configuring Other System Settings” chapter, section “Managing Software Licenses” of the Cisco Wide Area Application Services Configuration Guide.

Step 9 The Configure Lockdown Mode window appears (Figure 4-12).

Figure 4-12 Configure Lockdown Mode Window

Step 10 Lockdown mode is disabled by default.

• Leave the Enable Lockdown Mode check box unchecked to keep lockdown mode disabled.

When lockdown mode is disabled, all router and module communication commands behave normally.

• Check the Enable Lockdown Mode check box to enable lockdown mode.

When lockdown mode is enabled, the VMware vSphere Hypervisor host can be only be managed by the VMware vCenter Server using its internal user called vpxuser. All other configuration methods, such as the vSphere Client, PowerCLI, and vCLI are disabled.

Step 11 Click Next.

Step 12 The Virtual Machine Location window appears (Figure 4-13).

Figure 4-13 Virtual Machine Location Window

a. Select a location in the vCenter Server Inventory for the specified host’s virtual machines.

b. Click Next.

Step 13 The vSphere Client window is displayed with the Recent Tasks pane displaying a Completed status for this task (Figure 4-14).

Figure 4-14 vSphere Client Recent Tasks Pane

Step 14 Navigate to File > Deploy OVF Template... (Figure 4-15).

Figure 4-15 Deploy OVF Template... Menu Selection

Step 15 Download the vWAAS OVA from the Cisco Wide Area Application Services (WAAS) Download Software Page.

Step 16 Navigate to File > Deploy OVF Template... > Source.

Step 17 The Source window appears (Figure 4-16), where you select the OVA file.

Figure 4-16 Source Window

a. From the Deploy from a file or URL drop-down list, select the OVA file.

Step 18 The OVF Template Details window appears (Figure 4-17), where you can verify the OVF template details including product name, version, vendor, download size, size on disk, and a description.

Figure 4-17 OVF Template Details Window

a. To accept the selected OVA file, click Next.

Step 19 The Name and Location window appears (Figure 4-18), where you specify a name and location for the deployed template.

Figure 4-18 Name and Location Window

a. In the Name field, enter the name for the vWAAS VM.

b. At the Inventory Location listing, select the location to deploy (datacenter).

c. Click Next.

Step 20 The Deployment Configuration window appears (Figure 4-19).

Figure 4-19 Deployment Configuration Window

a. From the Configuration drop-down list, choose the vWAAS model to deploy. After you choose a vWAAS model, the window displays a description of the vWAAS model, such as “Deploy a vWAAS-200 connection profile with 2 vCPU, 4 GB RAM.”

b. Click Next.

Step 21 The Host/Cluster window is displayed (Figure 4-20), where you can choose a host or cluster to run the deployed template.

Figure 4-20 Host/Cluster Window

a. Select the ESXi host or cluster where you need to run the deployed template.

b. Click Next.

Step 22 The Disk Format window is displayed (Figure 4-21), which displays data store address and available disk space, in GB, and provisioning choices.

Figure 4-21 Disk Format Window

Note You must choose Thick Provision Eager Zeroed for vWAAS deployment.

a. Click Next.

Step 23 The Network Mapping window appears (Figure 4-22).

Figure 4-22 Network Mapping Window

a. Choose the required network mapping settings for your system.

b. Click Next.

Step 24 The Ready to Complete window appears (Figure 4-23), where you can verify the details of your deployment.

Figure 4-23 Ready to Complete Window

a. If the displayed details are the ones you have specified for your deployment, click the Power on after deployment check box.

b. To start the deployment task, click Finish.

Step 25 The Status window appears while the OVA file is being deployed (Figure 4-24) and then shows a completion message after the deployment has completed successfully (Figure 4-25).

Figure 4-24 Deployment In Progress Status Window

Figure 4-25 Deployment Completion Status Window

a. After deployment is completed, click Close.

Step 26 Navigate to Home > Inventory > Hosts and Clusters. The Inventory panel now shows the newly deployed device.

Step 27 Highlight the newly deployed device and open the Console window to display this device (Figure 4-26).

Figure 4-26 Console Window Displaying Newly Deployed Device