- MPLS Virtual Private Networks
- Multiprotocol BGP MPLS VPN
- MPLS VPN OSPF PE and CE Support
- MPLS VPN Support for EIGRP Between PE and CE
- IPv6 VPN over MPLS
- Assigning an ID Number to an MPLS VPN
- MPLS VPN Half-Duplex VRF
- MPLS VPN Show Running VRF
- MPLS VPN VRF CLI for IPv4 and IPv6 VPNs
- MPLS VPN BGP Local Convergence
- MPLS VPN Route Target Rewrite
- MPLS VPN Per VRF Label
- Multi-VRF Selection Using Policy-Based Routing
- MPLS VPN VRF Selection Using Policy-Based Routing
- VRF Aware System Message Logging
- MPLS VPN 6VPE per VRF Label
- Multi-VRF Support
- BGP Best External
- BGP PIC Edge for IP and MPLS-VPN
- MPLS over GRE
- Dynamic Layer 3 VPNs with Multipoint GRE Tunnels
- MPLS VPN 6VPE Support Over IP Tunnels
Contents
- IPv6 VPN over MPLS
- Finding Feature Information
- Prerequisites for IPv6 VPN over MPLS
- Restrictions for IPv6 VPN over MPLS
- Information About IPv6 VPN over MPLS
- IPv6 VPN over MPLS Overview
- Addressing Considerations for IPv6 VPN over MPLS
- Basic IPv6 VPN over MPLS Functionality
- IPv6 VPN Architecture Overview
- IPv6 VPN Next Hop
- MPLS Forwarding
- 6VPE over GRE Tunnels
- VRF Concepts
- IPv6 VPN Scalability
- Advanced IPv6 MPLS VPN Functionality
- Internet Access
- Multiautonomous-System Backbones
- Carrier Supporting Carriers
- How to Configure IPv6 VPN over MPLS
- Configuring a Virtual Routing and Forwarding Instance for IPv6
- Binding a VRF to an Interface
- Configuring a Static Route for PE-to-CE Routing
- Configuring eBGP PE-to-CE Routing Sessions
- Configuring the IPv6 VPN Address Family for iBGP
- Configuring Route Reflectors for Improved Scalability
- Configuring Internet Access
- Configuring the Internet Gateway
- Configuring iBGP 6PE Peering to the VPN PE
- Configuring the Internet Gateway as the Gateway to the Public Domain
- Configuring eBGP Peering to the Internet
- Configuring the IPv6 VPN PE
- Configuring a Default Static Route from the VRF to the Internet Gateway
- Configuring a Static Route from the Default Table to the VRF
- Configuring iBGP 6PE Peering to the Internet Gateway
- Configuring a Multiautonomous-System Backbone for IPv6 VPN
- Configuring the PE VPN for a Multiautonomous-System Backbone
- Configuring iBGP IPv6 VPN Peering to a Route Reflector
- Configuring IPv4 and Label iBGP Peering to a Route Reflector
- Configuring the Route Reflector for a Multiautonomous-System Backbone
- Configuring Peering to the PE VPN
- Configuring the Route Reflector
- Configuring Peering to the Autonomous System Boundary Router
- Configuring Peering to Another ISP Route Reflector
- Configuring the ASBR
- Configuring Peering with Router Reflector RR1
- Configuring Peering with the Other ISP ASBR2
- Configuring CSC for IPv6 VPN
- Configuration Examples for IPv6 VPN over MPLS
- Examples: IPv6 VPN over MPLS Routing
- Example: BGP IPv6 Activity Summary
- Example: Dumping the BGP IPv6 Tables
- Example: Dumping the IPv6 Routing Tables
- Examples: IPv6 VPN over MPLS Forwarding
- Example: PE-CE Connectivity
- Examples: PE Imposition Path
- Examples: PE Disposition Path
- Examples: Label Switch Path
- Examples: IPv6 VPN over MPLS VRF
- Examples: VRF Information
- Example: IPv6 VPN Configuration Using IPv4 Next Hop
- Additional References
- Feature Information for IPv6 VPN over MPLS
- Glossary
IPv6 VPN over MPLS
The Border Gateway Protocol over Multiprotocol Label Switching VPN feature is an implementation of the provider edge (PE)-based Virtual Private Network (VPN) model. In principle, there is no difference between IPv4 and IPv6 VPNs. In both IPv4 and IPv6, multiprotocol Border Gateway Protocol (BGP) is the center of the Multiprotocol Label Switching (MPLS) VPN for IPv6 (VPNv6) architecture. It is used to distribute IPv6 routes over the service provider backbone, using the same procedures to work with overlapping addresses, redistribution policies, and scalability issues.
- Finding Feature Information
- Prerequisites for IPv6 VPN over MPLS
- Restrictions for IPv6 VPN over MPLS
- Information About IPv6 VPN over MPLS
- How to Configure IPv6 VPN over MPLS
- Configuration Examples for IPv6 VPN over MPLS
- Additional References
- Feature Information for IPv6 VPN over MPLS
- Glossary
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Prerequisites for IPv6 VPN over MPLS
Your network must be running the following services before you configure IPv6 VPN operation:
- Multiprotocol Label Switching (MPLS) in provider backbone devices
- MPLS with Virtual Private Network (VPN) code in provider devices with VPN provider edge (PE) devices
- Border Gateway Protocol (BGP) in all devices providing a VPN service
- Cisco Express Forwarding switching in every MPLS-enabled device
- Class of Service (CoS) feature
Restrictions for IPv6 VPN over MPLS
IPv6 VPN over MPLS (6VPE) supports a Multiprotocol Label Switching (MPLS) IPv4-signaled core. An MPLS IPv6-signaled core is not supported.
Information About IPv6 VPN over MPLS
- IPv6 VPN over MPLS Overview
- Addressing Considerations for IPv6 VPN over MPLS
- Basic IPv6 VPN over MPLS Functionality
- Advanced IPv6 MPLS VPN Functionality
IPv6 VPN over MPLS Overview
Multiprotocol Border Gateway Protocol (BGP) is the center of the Multiprotocol Label Switching (MPLS) IPv6 Virtual Private Network (VPN) architecture in both IPv4 and IPv6. It is used to distribute IPv6 routes over the service provider backbone, using the same procedures to work with overlapping addresses, redistribution policies, and scalability issues.
Although IPv6 should not have overlapping address space, IPv6 addresses are prepended with a route distinguisher (RD). A network layer reachability information (NLRI) 3-tuple format (which contains length, IPv6 prefix, and label) is defined to distribute these routes using multiprotocol BGP. The extended community attribute (for example, the route target) is used to control redistribution of routing information by tagging exported routes and filtering imported ones.
For scalability, route reflectors can be used to concentrate routing paths and avoid a full provider edge (PE) mesh. BGP features in IPv6, such as route refresh, automatic route filtering, and outbound route filtering, help reduce the number of routes held in each PE. This document focuses on the following differences between IPv6 and IPv4:
- Creation of a new multiprotocol BGP IPv6 VPN address family and specification of a IPv6 VPN address format
- Specification of a new IPv6 VPN NLRI
- Specification of BGP next-hop encoding when the device has an IPv4-based MPLS core
Some IPv6 VPN features, such as interprovider and Carrier Supporting Carrier (CSC) topologies, are specific to BGP-MPLS IPv6 VPN. Others, such as the link between Autonomous System Boundary Routers (ASBRs), might support IPv4 only, IPv6 only, or both, regardless of the address family being transported.
Addressing Considerations for IPv6 VPN over MPLS
Regardless of the Virtual Private Network (VPN) model deployed, an addressing plan must be defined for the VPN that allows hosts to communicate with other sites using one site within one VPN, as well as with public resources.
VPN IPv4 sites often use private addressing for their addressing plan. These addresses do not need to be registered, and they are not routable on the public network. Whenever a host within a private site needs to access a public domain, it goes through a device that finds a public address on its behalf. With IPv4, this can be a network address translator or an application proxy.
Given the larger address space available with IPv6, the easiest approach to IPv6 addressing is to use IPv6 global addresses for the private addressing plan. Another approach is to use unique local addresses (ULAs). ULAs are easy to filter at site boundaries based on their scope. ULAs are also Internet service provider (ISP)-independent and can be used for communications inside a site without any permanent or intermittent Internet connectivity.
In IPv6 VPN over MPLS (6VPE), ULAs are treated as regular global addresses. The device configuration filters ULA prefixes to prevent them from appearing in the public domain. Link-local addresses on the peer will not be announced by Border Gateway Protocol (BGP) (IPv6 or IPv6 VPN) speakers.
A host within a private site that needs to access a public domain can do so through an IPv6 application proxy (such as a web proxy for accessing web pages), which accesses the public resource on the host’s behalf with a global routable address, or the host can use a public address of its own. In the latter case, if ULAs have been deployed, the IPv6 host also is configured with a routable global address. A source address selection algorithm is used to select one or the other, based on the destination address.
Basic IPv6 VPN over MPLS Functionality
IPv6 VPN over MPLS (6VPE) takes advantage of the coexistence between IPv6 and IPv4 by leveraging an existent Multiprotocol Label Switching (MPLS) IPv4 core network:
IPv6 VPN Architecture Overview
The figure below illustrates the important aspects of the IPv6 Virtual Private Network (VPN) architecture.
The customer edge (CE) devices are connected to the provider’s backbone using provider edge (PE) devices. The PE devices are connected using provider (P1 and P2 in the figure above) devices. The provider (P) devices are unaware of VPN routes, and, in the case of IPv6 over MPLS (6VPE), might support only IPv4. Only PE devices perform VPN-specific tasks. For 6VPE, the PE devices are dual-stack (IPv4 and IPv6) devices.
The routing component of the VPN operation is divided into core routing and edge routing. Core routing, which involves PE devices and P devices, typically is performed by an IPv4 Interior Gateway Protocol (IGP) such as Open Shortest Path First (OSPF) or Intermediate System-to-Intermediate System (IS-IS). In the figure above, the IGP distributes only routes internal to the provider’s autonomous system. The core routing enables connectivity among P and PE devices.
Edge routing takes place in two directions: routing between PE pairs and routing between a PE and a CE. Routing between PE pairs is achieved using multiprotocol internal BGP (iBGP) using the IPv6 VPN address family. This method distributes routes learned from CEs through PE-CE routing, using appropriate route export policies at the ingress PE device and appropriate route import policies at the egress PE device.
Routing between the CE and its PE is achieved using a routing protocol that is VPN routing and forwarding (VRF) aware. Static routes, external BGP (eBGP), and Enhanced Interior Gateway Routing Protocol (EIGRP) are VRF-instance aware. In the figure above, eBGP is used between the CE (CE1) and the PE (PE1). At the same time, the CE runs an IPv6 IGP within the VPN site (site1 in the figure above). The CE redistributes IGP routes into multiprotocol-eBGP address family IPv6. At the PE, these routes are installed in the VRF named vrf1, and forwarded to the remote PEs (PE2 in the figure above), according to export policies defined for this VRF.
IPv6 VPN Next Hop
When the device announces a prefix using the MP_REACH_NLRI attribute, the Multiprotocol Border Gateway Protocol (MP-BGP) running on one provider edge (PE) inserts a BGP next hop in the update message sent to a remote PE. This next hop is either propagated from the received update (for instance, if the PE is a route reflector), or it is the address of the PE sending the update message (the egress PE).
For the IPv6 Virtual Private Network (VPN) address family, the next hop must be an IPv6 VPN address, regardless of the nature of the network between the PE speakers. Because the route distinguisher (RD) has no significance (the address is not part of any VPN), it is set to 0. If the provider network is a native IPv6 network, the remaining part of the next hop is the IPv6 address of the egress PE. Otherwise, it is an IPv4 address used as an IPv6-mapped address (for example, ::FFFF:IPv4-address).
MPLS Forwarding
When it receives IPv6 traffic from one customer site, the ingress provider edge (PE) device uses Multiprotocol Label Switching (MPLS) to tunnel IPv6 Virtual Private Network (VPN) packets over the backbone toward the egress PE device identified as the Border Gateway Protocol (BGP) next hop. The ingress PE device prepends the IPv6 packets with the outer and inner labels before putting the packet on the egress interface.
Under normal operation, a provider (P) device along the forwarding path does not look inside the frame beyond the first label. The provider (P) device either swaps the incoming label with an outgoing one or removes the incoming label if the next device is a PE device. Removing the incoming label is called penultimate hop popping. The remaining label (BGP label) is used to identify the egress PE interface toward the customer site. The label also hides the protocol version (IPv6) from the last P device, which it would otherwise need to forward an IPv6 packet.
A P device is ignorant of the IPv6 VPN routes. The IPv6 header remains hidden under one or more MPLS labels. When the P device receives an MPLS-encapsulated IPv6 packet that cannot be delivered, it has two options. If the P device is IPv6 aware, it exposes the IPv6 header, builds an Internet Control Message Protocol (ICMP) for IPv6 message, and sends the message, which is MPLS encapsulated, to the source of the original packet. If the P device is not IPv6 aware, it drops the packet.
6VPE over GRE Tunnels
In some Cisco software releases, the ingress provider edge (PE) device uses IPv4 generic routing encapsulation (GRE) tunnels combined with IPv6 over MPLS (6VPE) over Multiprotocol Label Switching (MPLS) to tunnel IPv6 Virtual Private Network (VPN) packets over the backbone toward the egress PE device identified as the Border Gateway Protocol (BGP) next hop.
VRF Concepts
A virtual routing and forwarding (VRF) entity works with a private customer-specific Routing Information Base (RIB) and Forwarding Information Base (FIB). Although IPv4 and IPv6 routing tables are distinct, it is convenient for the two protocols to share the same VRF for a specific customer.
IPv6 VPN customers are likely to be existing VPNv4 customers that are either deploying dual-stack hosts and devices or shadowing some of their IPv4 infrastructure with IPv6 nodes. Several deployment models are possible. Some customers use separate logical interfaces for IPv4 and IPv6 and define separate VRFs on each. Although this approach provides flexibility to configure separate policies for IPv4 and IPv6, it prevents sharing the same policy. Another approach, the multiprotocol VRF, keeps a single VRF on the provider edge-customer edge (PE-CE) interface, and enables it for IPv4, IPv6, or both. It is then possible to define common or separate policies for each IP version. With this approach, a VRF is better defined as the set of tables, interfaces, and policies found at the PE, and is used by sites of a particular VPN connected to this PE.
The figure below illustrates the multiprotocol VRF, in which the VRF named vrf1is enabled for both IPv4 and IPv6 and is associated with two interfaces (IF1, IF2), two sets of tables (IPv4 RIB and FIB and IPv6 RIB and FIB), and a set of common or distinct policies.
IPv6 VPN Scalability
Provider edge (PE)-based Virtual Private Networks (VPNs) such as Border Gateway Protocol-Multiprotocol Label Switching (BGP-MPLS) IPv6 VPN scale better than customer edge (CE)-based VPNs. A network designer must consider scaling when designing the network. The following points need to be considered:
- Routing table size, which includes the size of virtual routing and forwarding (VRF) tables and BGP tables
- Number of BGP sessions, which grows as a square number of PEs
Routing table size concerns occur with PEs that handle many customer sites. Not only do these PEs have one Routing Information Base (RIB) and Forwarding Information Base (FIB) per connected customer, but also the PEs’ BGP tables, which total all entries from individual VRFs, grow accordingly. Another scalability problem occurs when the number of PEs in the provider network grows beyond a certain level. Assuming that a significant number of sites belonging to the same VPN are spread over many PEs, the number of multiprotocol BGP sessions may rapidly become prohibitive: (n -1) x n /2, where n is the number of PEs.
The following features are included in IPv6 VPN over MPLS:
- Route refresh and automatic route filtering—Limits the size of routing tables, because only routes imported into a VRF are kept locally. When the import policy changes, a route refresh can be sent to query a retransmission of routing updates.
- Outbound route filtering (ORF)—Allows the ingress PE to advertise filters to the egress PE so that updates are not sent unnecessarily over the network.
- Route reflectors—Route reflectors (RRs) are internal BGP (iBGP) peers that propagate iBGP routes learned from other iBGP peers. RRs are used to concentrate iBGP sessions.
Advanced IPv6 MPLS VPN Functionality
Advanced Multiprotocol Label Switching (MPLS) features such as accessing the Internet from a Virtual Private Network (VPN) for IPv4, multiautonomous-system backbones, and Carrier Supporting Carriers (CSCs) are generally the same for IPv6 as for IPv4. However, there are differences in addressing and in the way IPv6 over MPLS (6VPE) operates over an IPv4 backbone.
The following sections describe concepts for advanced IPv6 MPLS VPN functionality:
Internet Access
Most Virtual Private Network (VPN) sites require access to the Internet. RFC 4364 describes a set of models for enabling IPv4 and IPv6 VPN access to the Internet. In one model, one interface is used by the customer edge (CE) to connect to the Internet and a different one to connect to the virtual routing and forwarding (VRF) instance. Another model is in which all Internet routes are redistributed into the VRF; however, this approach has the disadvantage of requiring the Internet routes be replicated in each VRF.
In one scenario, a static route is inserted into the VRF table, with a next hop that points to the Internet gateway found in the IPv6 default table. The figure below illustrates this scenario, in which Internet access is provided to the customer in the VRF named vrf1.
A customer site that has access public resources over the Internet must be known by a public prefix. Unlike IPv4, IPv6 does not offer a Network Address Translation (NAT) mechanism that translates private addresses into public addresses when leaving the site boundaries. This implies that hosts within the site speak with public addresses and appear in the public domain.
For outbound traffic, the default route configured in the VRF table at ingress provider edge (PE1) directs traffic for destinations outside the VPN to the Internet gateway.
For inbound traffic, a route must exist at the Internet gateway to direct the traffic for a customer site via its PE of attachment (PE1 in the figure above). This route can be distributed by the ingress PE (PE1) using multiprotocol internal Border Gateway Protocol (iBGP) (with the IPv6 address family configuration), so no specific configuration is needed on a per-VPN PE basis at the Internet gateway. Nevertheless, for inbound traffic at PE1, a route must exist in the default table for the customer site global prefix pointing to the VRF of the site.
Multiautonomous-System Backbones
The problem of interprovider Virtual Private Networks (VPNs) is similar for IPv6 and IPv4, assuming that IPv6 was deployed everywhere IPv4 was deployed.
In IPv6 deployments that cross autonomous system boundaries, providers may have to obtain a peering model, or work with the peering model put in place for VPNv4.
The figure below illustrates interprovider scenarios in IPv6 VPN.
Depending on the network protocol used between Autonomous System Boundary Routers (ASBRs), the three scenarios shown in the figure above can have several implementation options. For instance, scenario B, which suggests a multiprotocol external Border Gateway Protocol (eBGP) IPv6 VPN peering between ASBRs, could use either an IPv6 or an IPv4 link.
In scenario C, multihop multiprotocol eBGP redistributes IPv6 VPN routes across route reflectors in different autonomous systems. Labeled IPv4 routes to the provider edge (PE) devices (in the IPv6 over MPLS case) need to be advertised across ASBRs so that a complete labeled switch path is set up end to end.
Carrier Supporting Carriers
The Carrier Supporting Carrier (CSC) feature provides Virtual Private Network (VPN) access to a customer service provider, so this service needs to exchange routes and send traffic over the Internet service provider (ISP) Multiprotocol Label Switching (MPLS) backbone. The only difference from a regular provider edge (PE) is that it provides MPLS-to-MPLS forwarding on the CSC-customer edge (CE) to CSC-PE interface, rather than IP-to-MPLS forwarding.
The figure below highlights the two ISPs’ interface.
How to Configure IPv6 VPN over MPLS
- Configuring a Virtual Routing and Forwarding Instance for IPv6
- Binding a VRF to an Interface
- Configuring a Static Route for PE-to-CE Routing
- Configuring eBGP PE-to-CE Routing Sessions
- Configuring the IPv6 VPN Address Family for iBGP
- Configuring Route Reflectors for Improved Scalability
- Configuring Internet Access
- Configuring a Multiautonomous-System Backbone for IPv6 VPN
- Configuring CSC for IPv6 VPN
Configuring a Virtual Routing and Forwarding Instance for IPv6
A virtual routing and forwarding (VRF) instance is an address family-independent object that can be enabled and configured for each of the supported address families. Configuring a VRF consists of the following three steps:
- Configuring the address-family-independent part of the VRF
- Enabling and configuring IPv4 for the VRF
- Enabling and configuring IPv6 for the VRF
A VRF is given a name and a route distinguisher (RD). The RD is configured outside the context of the address family, although the RD is used to distinguish overlapping addresses within the context of a particular Border Gateway Protocol (BGP) address family. Having separate RDs for IPv4 VPN addresses and IPv6 VPN addresses does not matter. On Cisco devices, the RDs are the same in order to simplify configuration and VPN management.
Users can configure policies in common between IPv4 and IPv6 when not using an address family context. This feature is shared route targets (import and export), and it is useful in a migration scenario, where IPv4 policies already are configured and IPv6 policies should be the same as the IPv4 policies.
The IPv4 and IPv6 address family can each be enabled and configured separately. Note that the route-target policies entered at this level override global policies that may have been specified during address family-independent configuration.
1.
enable
2.
configure terminal
3.
mpls ipv6 vrf
4.
vrf definition
vrf-name
5.
rd
route-distinguisher
6.
route-target {import |
export |
both}
route-target-ext-community
7.
exit
8.
address-family ipv4 [mdt |
multicast |
tunnel |
unicast [vrf
vrf-name] |
vrf
vrf-name]
9.
route-target {import |
export |
both}
route-target-ext-community
10.
exit
11.
address-family ipv6 [vrf
vrf-name] [unicast |
multicast]
12.
route-target {import |
export |
both}
route-target-ext-community
DETAILED STEPS
Binding a VRF to an Interface
In order to specify which interface belongs to which virtual routing and forwarding (VRF) instance, use the vrf forwarding command for both IPv4 and IPv6. An interface cannot belong to more than one VRF. When the interface is bound to a VRF, previously configured addresses (IPv4 and IPv6) are removed, and they must be reconfigured.
1.
enable
2.
configure terminal
3.
interface
type number
4.
vrf forwarding
vrf-name
5.
ip address
ip-address mask [secondary]
6.
ipv6
address
{ipv6-address
/
prefix-length |
prefix-name
sub-bits/prefix-length
DETAILED STEPS
Configuring a Static Route for PE-to-CE Routing
1.
enable
2.
configure terminal
3.
ipv6
route
[vrf
vrf-name]
ipv6-prefix
/
prefix-length {ipv6-address |
interface-type
interface-number [ipv6-address]} [nexthop-vrf [vrf-name1 |
default]] [administrative-distance] [administrative-multicast-distance |
unicast |
multicast] [next-hop-address] [tag
tag]
DETAILED STEPS
Configuring eBGP PE-to-CE Routing Sessions
1.
enable
2.
configure terminal
3.
router bgp
autonomous-system-number
4.
address-family ipv6 [vrf
vrf-name] [unicast |
multicast]
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
6.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
DETAILED STEPS
Configuring the IPv6 VPN Address Family for iBGP
1.
enable
2.
configure terminal
3.
router bgp
autonomous-system-number
4.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
6.
address-family vpnv6 [unicast]
7.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
8.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-community [both |
standard |
extended]
9.
extended]
exit
DETAILED STEPS
Configuring Route Reflectors for Improved Scalability
In this task, two route reflectors (RRs) are configured for redundancy reasons. Deploying RRs improves scalability by drastically reducing the number of Border Gateway Protocol (BGP) sessions. One RR usually peers with many internal Border Gateway Protocol (iBGP) speakers, preventing a full mesh of BGP sessions.
In a Multiprotocol Label Switching (MPLS)-based core, RRs are not part of the label switch paths and can be located anywhere in the network. For example, in a flat RR design, RRs can be deployed at Level 1 points of presence (POPs) and peer together in a full-mesh topology. In a hierarchical RR design, RRs could be deployed at Level 1 and Level 2 POPs, with Level 1 POPs peering together and with Level 2 RRs.
In a typical case where IPv6 over MPLS (6VPE) is deployed in a preexisting MPLS network (for example, providing VPNv4 services), it is likely that some RR design is already in place, and a similar RR infrastructure for IPv6 Virtual Private Network (VPN) services can be deployed. The figure below illustrates the main peering points between the RR in the ISP POP and the set of its RR clients.
The following list of BGP RR clients must be configured at each IPv6 RR (RR6 and RR6_1 in the figure above) device, at each POP:
- Provider edge (PE) devices (PE-VPN) of the POP providing IPv6 VPN access to the ISP customers. This includes both IPv6 VPN (6VPE) peering for interconnecting customer sites and IPv6 peering (6PE) for providing Internet access to VPN customers (see the “Configuring Internet Access” section).
- Internet gateway (IGW) located in the POP in order to provide PE customers with access to the IPv6 Internet (see the see the “Configuring Internet Access” section).
- RRs from other service providers. This feature is used to provide interautonomous-system connectivity, and it includes both IPv6 and IPv6 VPN peering. This service is described in the “Configuring a Multiautonomous-System Backbone for IPv6 VPN” section.
- RRs in other POPs. All RRs peer together, with both IPv6 and IPv6 VPN address families enabled.
1.
enable
2.
configure
terminal
3.
router
bgp
autonomous-system-number
4.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
6.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
7.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
8.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
9.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
10.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
11.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
12.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
ebgp-multihop [ttl]
13.
address-family
ipv6
14.
neighbor
{ip-address |
peer-group-name |
ipv6-address}
activate
15.
neighbor
{
ip-address
|
ipv6-address |
peer-group-name}
send-label
16.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
route-reflector-client
17.
neighbor
{ip-address |
peer-group-name |
ipv6-address}
activate
18.
neighbor
{
ip-address
|
ipv6-address |
peer-group-name}
send-label
19.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
route-reflector-client
20.
neighbor
{ip-address |
peer-group-name |
ipv6-address}
activate
21.
neighbor
{
ip-address
|
ipv6-address |
peer-group-name}
send-label
22.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
route-reflector-client
23.
exit
24.
address-family
vpnv6
[unicast
25.
neighbor
{ip-address |
peer-group-name |
ipv6-address}
activate
26.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
send-community [both |
standard |
extended]
27.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
route-reflector-client
28.
neighbor
{ip-address |
peer-group-name |
ipv6-address}
activate
29.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
send-community [both |
standard |
extended]
30.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
route-reflector-client
31.
neighbor
{ip-address |
peer-group-name |
ipv6-address}
activate
32.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
send-community [both |
standard |
extended]
33.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
route-reflector-client
34.
neighbor
{ip-address |
ipv6-address |
peer-group-name}
next-hop-unchanged [allpaths
DETAILED STEPS
Configuring Internet Access
Customers with IPv6 Virtual Private Network (VPN) access need to have access to the Internet through IPv6. The design of this service is similar to a global Internet access service. IPv6 VPN over MPLS (6VPE) devices located in a Level 1 point of presence (POP) (colocated with an IGW device) can access the Internet gateway (IGW) natively, whereas 6VPE devices located in Level 2 and Level 3 POPs with no direct access to the IGW can access the IGW in their closest Level 1 POP over 6PE.
Configuring VPN Internet access in such a 6VPE device involves configuring Border Gateway Protocol (BGP) peering with the IGW (in most cases through the IPv6 RR, as described in the “Configuring Route Reflectors for Improved Scalability” section). Then the user must configure cross-table routing to enable communication between the private domain (the VRF) and the public domain (the Internet).
The figure above illustrates the following configuration tasks:
Configuring the Internet Gateway
- Configuring iBGP 6PE Peering to the VPN PE
- Configuring the Internet Gateway as the Gateway to the Public Domain
- Configuring eBGP Peering to the Internet
Configuring iBGP 6PE Peering to the VPN PE
1.
enable
2.
configure terminal
3.
router bgp
autonomous-system-number
4.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
6.
address-family ipv6
7.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
8.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-label
DETAILED STEPS
Configuring the Internet Gateway as the Gateway to the Public Domain
Use the 6PE peering configuration established in the “Configuring iBGP 6PE Peering to the VPN PE” section.
1.
enable
2.
configure terminal
3.
router bgp
autonomous-system-number
4.
address-family ipv6
5.
network
ipv6-address/prefix-length
6.
exit
DETAILED STEPS
Configuring eBGP Peering to the Internet
1.
enable
2.
configure terminal
3.
router bgp
autonomous-system-number
4.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
address-family ipv6
6.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
7.
aggregate-address
address
mask
[as-set] [summary-only] [suppress-map
map-name] [advertise-map
map-name] [attribute-map
map-name]
DETAILED STEPS
Configuring the IPv6 VPN PE
- Configuring a Default Static Route from the VRF to the Internet Gateway
- Configuring a Static Route from the Default Table to the VRF
- Configuring iBGP 6PE Peering to the Internet Gateway
Configuring a Default Static Route from the VRF to the Internet Gateway
1.
enable
2.
configure
terminal
3.
ipv6
route
[vrf
vrf-name]
ipv6-prefix/prefix-length {ipv6-address |
interface-type
interface-number [ipv6-address]} [nexthop-vrf [vrf-name1 |
default]] [administrative-distance] [administrative-multicast-distance |
unicast |
multicast] [next-hop-address] [tag
tag]
DETAILED STEPS
Configuring a Static Route from the Default Table to the VRF
1.
enable
2.
configure
terminal
3.
ipv6
route
[vrf
vrf-name]
ipv6-prefix/prefix-length {ipv6-address |
interface-type
interface-number [ipv6-address]} [nexthop-vrf [vrf-name1 |
default]] [administrative-distance] [administrative-multicast-distance |
unicast |
multicast] [next-hop-address] [tag
tag]
DETAILED STEPS
Configuring iBGP 6PE Peering to the Internet Gateway
1.
enable
2.
configure terminal
3.
router bgp
autonomous-system-number
4.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
6.
address-family ipv6 [vrf
vrf-name] [unicast |
multicast]
7.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
8.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-label
9.
network
ipv6-address/prefix-length
DETAILED STEPS
Configuring a Multiautonomous-System Backbone for IPv6 VPN
Two Virtual Private Network (VPN) sites may be connected to different autonomous systems because the sites are connected to different service providers. The provider edge (PE) devices attached to that VPN is then unable to maintain the internal Border Gateway Protocol (iBGP) connections with each other or with a common route reflector. In this situation, there must be some way to use external BGP (eBGP) to distribute VPN-IPv6 addresses.
The following configuration example illustrates two scenarios, one in which a multiprotocol eBGP-IPv6 VPN peering between autonomous system boundary routers (ASBRs) uses an IPv4 link, and the same scenario using an IPv6 link. If the peering between ASBRs is performed over an IPv4 link, the BGP configuration on ASBR1 is as follows:
router bgp 1001 no bgp default ipv4-unicast no bgp default route-target filter neighbor 192.1.1.1 remote-as 1002 neighbor 192.168.2.11 remote-as 1001 neighbor 192.168.2.11 update-source Loopback1 ! address-family vpnv6 !Peering to ASBR2 over an IPv4 link neighbor 192.1.1.1 activate neighbor 192.1.1.1 send-community extended !Peering to PE1 over an IPv4 link neighbor 192.168.2.11 activate neighbor 192.168.2.11 next-hop-self neighbor 192.168.2.11 send-community extended
If the peering between ASBRs is performed over an IPv6 link, the BGP configuration on ASBR1 is as follows:
router bgp 1001 neighbor 2001:DB8:101::72d remote-as 1002 ! address-family vpnv6 !Peering to ASBR2 over an IPv6 link neighbor 2001:DB8:101::72d activate neighbor 2001:DB8:101::72d send-community extended
The next several tasks describe how to configure the PE VPN for a multiautonomous-system backbone using multihop multiprotocol eBGP to redistribute VPN routes across route reflectors (RRs) in different autonomous systems. Labeled IPv4 routes to the PEs are advertised across ASBRs so that a complete label switch path (LSP) is set up end to end.
In this scenario, the ASBRs are not VPN aware; only the RRs are VPN aware. The following configuration should be available and understood:
The ASBRs are providing the PEs’ loopback addresses to service providers they peer with. That includes: For the VPN PE’s IPv4 loopback address, the address providing is performed over multiprotocol BGP, with the label, up to the remote PEs, so that the label establishes an end-to-end LSP. Therefore, the following MP-BGP peering was set up for VPNv4: - The VPN RRs of each service provider are peering together over eBGP and exchanging VPN routes. The next hop is forwarded unchanged, so that the end-to-end LSP is not via RRs.
To enable IPv6 VPN interautonomous-system access in this scenario, the ISP needs to modify the configurations at the PE VPN and at the RR. The same RRs are set up to provide a similar service for VPNv4. In that context, because the peering between the RR and the ASBR and between ASBRs is solely to exchange labels for IPv4 next hops used by both IPv4 VPN and IPv6 VPN, the ASBRs remain completely IPv6 unaware, and no configuration change is required there.
The figure below shows the BGP peering points required to enable IPv6 interprovider connectivity from the PE-VPN device (providing IPv6 VPN access) to the xxCom network.
The following additional BGP peerings are necessary to enable interautonomous-system communication from the IPv6 VPN PE located in the Level 2 point of presence (POP):
- IPv4 with label peering from the PE VPN to the route reflector named RR1 (which is already configured if VPNv4 interautonomous system is deployed on the same nodes, using the same LSP).
- IPv4 with label peering from RR1 to ASBR1.
- IPv4 with label peering between ASBR1 and ASBR2.
- IPv6 VPN peering between RR1 and RR2 (which is the route reflector in the other autonomous systems) to exchange IPv6 VPN routes.
- IPv6 VPN peering with RR1. If the same route reflectors used to scale the IPv6 VPN service are used for interautonomous-system capability, then this function might also be already configured (see the “Configuring Route Reflectors for Improved Scalability” section ).
Configuring the multiautonomous-system backbone for IPv6 VPN consists of the following tasks:
- Configuring the PE VPN for a Multiautonomous-System Backbone
- Configuring the Route Reflector for a Multiautonomous-System Backbone
- Configuring the ASBR
Configuring the PE VPN for a Multiautonomous-System Backbone
- Configuring iBGP IPv6 VPN Peering to a Route Reflector
- Configuring IPv4 and Label iBGP Peering to a Route Reflector
Configuring iBGP IPv6 VPN Peering to a Route Reflector
Perform this task to configure internal Border Gateway Protocol (iBGP) IPv6 Virtual Private Network (VPN) peering to a route reflector named RR1.
1.
enable
2.
configure terminal
3.
router bgp
autonomous-system-number
4.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
6.
address-family vpnv6 [unicast]
7.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
8.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-community [both |
standard |
extended]
9.
exit
DETAILED STEPS
Configuring IPv4 and Label iBGP Peering to a Route Reflector
Perform this task to configure IPv4 and label internal Border Gateway Protocol (iBGP) peering to a route reflector named RR1.
1.
enable
2.
configure terminal
3.
router bgp
autonomous-system-number
4.
address-family ipv4 [mdt |
multicast |
tunnel |
unicast [vrf
vrf-name] |
vrf
vrf-name]
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
6.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-label
DETAILED STEPS
Configuring the Route Reflector for a Multiautonomous-System Backbone
- Configuring Peering to the PE VPN
- Configuring the Route Reflector
- Configuring Peering to the Autonomous System Boundary Router
- Configuring Peering to Another ISP Route Reflector
Configuring Peering to the PE VPN
1.
enable
2.
configure terminal
3.
router bgp
autonomous-system-number
4.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
6.
address-family vpnv6 [unicast]
7.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
8.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-community [both |
standard |
extended]
9.
exit
10.
address-family ipv4 [mdt |
multicast |
tunnel |
unicast [vrf
vrf-name] |
vrf
vrf-name]
11.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
12.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-label
13.
exit
DETAILED STEPS
Configuring the Route Reflector
1.
enable
2.
configure terminal
3.
router bgp
autonomous-system-number
4.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
6.
address-family vpnv6 [unicast]
7.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
8.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-community [both |
standard |
extended]
9.
neighbor {ip-address |
ipv6-address |
peer-group-name}
route-reflector-client
10.
exit
11.
address-family
ipv4
[mdt |
multicast |
tunnel |
unicast [vrf
vrf-name] |
vrf
vrf-name]
12.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
13.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-label
14.
exit
DETAILED STEPS
Configuring Peering to the Autonomous System Boundary Router
1.
enable
2.
configure
terminal
3.
router
bgp
autonomous-system-number
4.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
6.
address-family
ipv4
[mdt |
multicast |
tunnel |
unicast [vrf
vrf-name] |
vrf
vrf-name]
7.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
8.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-label
DETAILED STEPS
Configuring Peering to Another ISP Route Reflector
Perform this task to configure peering to an Internet service provider (ISP) route reflector named RR2.
1.
enable
2.
configure
terminal
3.
router
bgp
autonomous-system-number
4.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
6.
neighbor {ip-address |
ipv6-address |
peer-group-name}
ebgp-multihop [ttl]
7.
address-family
vpnv6
[unicast]
8.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
9.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-community [both |
standard |
extended]
10.
neighbor {ip-address |
ipv6-address |
peer-group-name}
next-hop-unchanged [allpaths]
DETAILED STEPS
Configuring the ASBR
Configuring Peering with Router Reflector RR1
1.
enable
2.
configure
terminal
3.
router
bgp
autonomous-system-number
4.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
6.
address-family
ipv4
[mdt |
multicast |
tunnel |
unicast [vrf
vrf-name] |
vrf
vrf-name
7.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
8.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-label
9. exit
DETAILED STEPS
Configuring Peering with the Other ISP ASBR2
1.
enable
2.
configure
terminal
3.
router
bgp
autonomous-system-number
4.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
5.
neighbor {ip-address |
ipv6-address |
peer-group-name}
update-source
interface-type
interface-number
6.
neighbor {ip-address |
ipv6-address |
peer-group-name}
ebgp-multihop [ttl]
7.
address-family
ipv4
[mdt |
multicast |
tunnel |
unicast [vrf
vrf-name] |
vrf
vrf-name]
8.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
9.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-label
10.
network
{network-number [mask
network-mask] |
nsap-prefix} [route-map
map-tag]
11.
network
{network-number [mask
network-mask] |
nsap-prefix} [route-map
map-tag]
DETAILED STEPS
Configuring CSC for IPv6 VPN
Perform this task to configure CsC-PE1 peering configuration with CsC-CE1.
1.
enable
2.
configure
terminal
3.
hostname
name
4.
router
bgp
autonomous-system-number
5.
address-family
ipv6
[vrf
vrf-name] [unicast |
multicast]
6.
neighbor {ip-address |
ipv6-address |
peer-group-name}
remote-as
as-number
7.
neighbor {ip-address |
ipv6-address |
peer-group-name}
activate
8.
neighbor {ip-address |
ipv6-address |
peer-group-name}
send-label
DETAILED STEPS
Configuration Examples for IPv6 VPN over MPLS
- Examples: IPv6 VPN over MPLS Routing
- Examples: IPv6 VPN over MPLS Forwarding
- Examples: IPv6 VPN over MPLS VRF
- Example: IPv6 VPN Configuration Using IPv4 Next Hop
Examples: IPv6 VPN over MPLS Routing
- Example: BGP IPv6 Activity Summary
- Example: Dumping the BGP IPv6 Tables
- Example: Dumping the IPv6 Routing Tables
Example: BGP IPv6 Activity Summary
Device# show bgp ipv6 summary
For address family: IPv6 Unicast
BGP router identifier 192.168.2.126, local AS number 33751
BGP table version is 15, main routing table version 15
12 network entries using 1692 bytes of memory
22 path entries using 1672 bytes of memory
5/4 BGP path/bestpath attribute entries using 580 bytes of memory
14 BGP rrinfo entries using 336 bytes of memory
2 BGP AS-PATH entries using 48 bytes of memory
0 BGP route-map cache entries using 0 bytes of memory
0 BGP filter-list cache entries using 0 bytes of memory
BGP using 4328 total bytes of memory
Dampening enabled. 0 history paths, 0 dampened paths
BGP activity 13/1 prefixes, 23/1 paths, scan interval 60 secs
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
192.168.2.146 4 33751 991 983 15 0 0 16:26:21 10
192.168.2.147 4 33751 991 983 15 0 0 16:26:22 10
FE80::4F6B:44 GigabitEthernet1/0/0
4 20331 982 987 15 0 0 14:55:52 1
Example: Dumping the BGP IPv6 Tables
Each table (for example, BGP IPv6, BGP IPv6 VPN) can be reviewed individually, as shown in the following example:
Device# show bgp ipv6 unicast
BGP table version is 15, local router ID is 192.168.2.126
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
* i2001:DB8:100::/48 ::FFFF:192.168.2.101 0 100 0 10000 ?
*>i ::FFFF:192.168.2.101 0 100 0 10000 ?
* i2001:DB8::1/128 ::FFFF:192.168.2.101 0 100 0 i
*>i ::FFFF:192.168.2.101 0 100 0 i
Example: Dumping the IPv6 Routing Tables
IPv6 routing tables identify each routing protocol contributor to routable entries, as shown in the following example:
Device# show ipv6 route
IPv6 Routing Table - default - 13 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
B - BGP, R - RIP, I1 - ISIS L1, I2 - ISIS L2
IA - ISIS interarea, IS - ISIS summary
O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
B 2001:DB8:100::/48 [200/0]
via 192.168.2.101 Default-IP-Routing-Table, indirectly connected
B 2001:DB8::1/128 [200/0]
via 192.168.2.101 Default-IP-Routing-Table, c
LC 2001:DB8::26/128 [0/0]
via Loopback0, receive
From an IPv6 routing perspective, entries reachable over the MPLS backbone are listed as being indirectly connected, because MPLS is providing a Layer 2 tunnel mechanism.
Examples: IPv6 VPN over MPLS Forwarding
- Example: PE-CE Connectivity
- Examples: PE Imposition Path
- Examples: PE Disposition Path
- Examples: Label Switch Path
Example: PE-CE Connectivity
The ipv6 ping and traceroute commands are useful to check connectivity from a provider edge (PE) to a customer edge (CE), whether locally attached or remote over the Multiprotocol Label Switching (MPLS) backbone.
When a device is locally attached, one can use the ipv6 ping command with the CE link-local address (used for external BGP peering), as shown in the following example:
Device# ping FE80::4F6B:44% Loopback0 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::4F6B:44, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/33/48 ms
The ipv6 ping command also can be used to test remote PE or CE reachability, but only IPv6 global addresses can be used (link-local addresses are not advertised beyond the link):
Device# ping 2001:DB8:1120:1::44 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2001:DB8:1120:1:44::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/33/48 ms
Note that the ping ipv6 and traceroute command functions over MPLS require PEs and CEs to announce one IPv6 global prefix. Each 6PE device announces 2001:DB8::PE#/128, filtered at the autonomous system edge. Each IPv6 CE configures 2001:DB8:prefix:CE#/128 and announces it as part as its less-specific prefix (2001:DB8:prefix::/n).
Reachability of remote PEs and CEs can be tested by using the traceroute command. If you have configured all PEs with the no mpls ip propagate-ttl forwarded command, when the traceroute command is executed from a CE, its output will show only the IPv6 nodes:
Device# traceroute 2001:DB8::1 Type escape sequence to abort. Tracing the route to 2001:DB8::1 1 2001:DB8::26 [AS 33751] 32 msec 32 msec 20 msec 2 2001:DB8::1 [AS 33751] [MPLS: Label 73 Exp 0] 20 msec 20 msec 20 msec 3 2001:DB8::1 [AS 33751] 28 msec 20 msec 20 msec
After the P devices have been upgraded with images that support ICMPv6, the traceroute command executed on the PE device (Time to Live [TTL] is then propagated) will also show P devices’ responses, as shown in the following example:
Device# traceroute 2001:DB8::1 Type escape sequence to abort. Tracing the route to 2001:DB8::1 1 ::FFFF:172.20.25.1 [MPLS: Labels 38/73 Exp 0] 40 msec 32 msec 32 msec 2 ::FFFF:172.20.10.1 [MPLS: Labels 30/73 Exp 0] 60 msec 32 msec 32 msec 3 2001:DB8::1 [MPLS: Label 73 Exp 0] 32 msec 32 msec 16 msec
When run from a 6VPE device, both the ping ipv6 and traceroute commands accept a vrf argument, exactly as in the case of VPNv4.
Note that the traceroute command is useful for evaluating the path across the MPLS backbone, but not for troubleshooting data-plane failures. The P devices are IPv6 unaware (and are also VPNv4 unaware), so the ICMPv6 messages that they generate in response to the traceroute command are forwarded to the egress PE using the received label stack. The egress PE can route the ICMPv6 message to the source of the traceroute. When the MPLS path is broken, it is also broken from the ICMP message, which cannot reach the egress PE.
Examples: PE Imposition Path
On Cisco devices, the most useful tool for troubleshooting the imposition path for IPv6 is the show ipv6 cef command.
You can use the show ipv6 cef command to display the IPv6 forwarding table with label stacks used for each destination prefix, as shown in the following example:
Device# show ipv6 cef 2001:DB8:100::/48 nexthop 172.20.25.1 GigabitEtherent0/0/0 label 38 72 2001:DB8::1/128 nexthop 172.20.25.1 GigabitEtherent0/0/0 label 38 73 2001:DB8::26/128 attached to Loopback0, receive
You can use the show ipv6 cef command to display details for a specific IPv6 entry in the forwarding table and to analyze how the destination was resolved and the label stack computed, as shown in the following example:
Device# show ipv6 cef 2001:DB8:100::/48 internal
2001:DB8:100::/48, epoch 0, RIB[B], refcount 4
sources: RIB
..
recursive via 192.168.2.101[IPv4:Default] label 72, fib 0252B1F8, 1 terminal fib
path 024F56A8, path list 024F0BA8, share 0/1, type attached nexthop
ifnums: (none)
path_list contains at least one resolved destination(s). HW IPv4 notified.
nexthop 172.20.25.1 GigabitEtherent0/0/0 label 38, adjacency IP adj out of GigabitEtherent0/0/0 0289BEF0
output chain: label 72 label 38 TAG adj out of GigabitEtherent0/0/0 0289BD80
The detailed output in the previous example shows that each label composing the label stack has a different origin that can be tracked down individually. The Border Gateway Protocol (BGP) table has the bottom label, as shown in the following example:
Device# show bgp ipv6 unicast 2001:DB8:100::/48
BGP routing table entry for 2001:DB8:100::/48, version 2
Paths: (2 available, best #2, table default)
Advertised to update-groups:
1
10000
::FFFF:192.168.2.101 (metric 30) from 192.168.2.147 (192.168.2.147)
Origin incomplete, metric 0, localpref 100, valid, internal
Originator: 192.168.2.101, Cluster list: 192.168.2.147,
mpls labels in/out nolabel/72
10000
::FFFF:192.168.2.101 (metric 30) from 192.168.2.146 (192.168.2.146)
Origin incomplete, metric 0, localpref 100, valid, internal, best
Originator: 192.168.2.101, Cluster list: 192.168.2.146,
mpls labels in/out nolabel/72
Label Distribution Protocol (LDP), as shown in this example, displays the other labels:
Device# show mpls ldp bindings 192.168.2.101 32
lib entry: 192.168.2.101/32, rev 56
local binding: label: 40
remote binding: lsr: 192.168.2.119:0, label: 38
Device# show mpls ldp bindings 172.20.25.0 24
lib entry: 172.20.25.0/24, rev 2
local binding: label: imp-null
remote binding: lsr: 192.168.2.119:0, label: imp-null
Examples: PE Disposition Path
Use the following examples to troubleshoot the disposition path.
The following example shows the Multiprotocol Label Switching (MPLS) forwarding table information for troubleshooting the disposition path.
Device# show mpls forwarding-table Local Outgoing Prefix Bytes Label Outgoing Next Hop Label Label or VC or Tunnel Id Switched interface 16 Pop Label 192.168.2.114/32 0 GE0/0/0 point2point 17 26 192.168.2.146/32 0 GE0/0/0 point2point .. 72 No Label 2001:DB8:100::/48 63121 GE1/0/0 point2point 73 Aggregate 2001:DB8::1/128 24123
The following example shows the label used for switching, which has been announced by iBGP (6PE in this example) and can be checked:
Device# show bgp ipv6 2001:DB8:100::/48
BGP routing table entry for 2001:DB8:100::/48, version 2
Paths: (1 available, best #1, table default)
Advertised to update-groups:
2
10000
FE80::2710:2 (FE80::2710:2) from FE80::2710:2 GigabitEthernet1/0/0 (192.168.2.103)
Origin incomplete, metric 0, localpref 100, valid, external, best,
Examples: Label Switch Path
Because the 6PE and 6VPE label switch path (LSP) endpoints are IPv4 addresses, the IPv4 tools for troubleshooting LSPs are useful for detecting data-plane failures that would lead to IPv6 traffic black-holing.
The following example displays the LSP IPv4 end to analyze the LSP:
Device# show ipv6 route 2001:DB8::1/128
Routing entry for 2001:DB8::1/128
Known via "bgp 33751", distance 200, metric 0, type internal
Route count is 1/1, share count 0
Routing paths:
192.168.2.101%Default-IP-Routing-Table indirectly connected
MPLS Required
Last updated 02:42:12 ago
The following example shows the traceroute LSP:
Device# traceroute mpls ipv4 192.168.2.101/32 verbose
Tracing MPLS Label Switched Path to 192.168.2.101/32, timeout is 2 seconds
Codes: '!' - success, 'Q' - request not transmitted,
'.' - timeout, 'U' - unreachable,
'R' - downstream router but not target,
'M' - malformed request
Type escape sequence to abort.
0 172.20.25.2 0.0.0.0 MRU 1500 [Labels: 38 Exp: 0]
R 1 172.20.25.1 0.0.0.0 MRU 1500 [Labels: 30 Exp: 0] 40 ms, ret code 6
R 2 172.20.10.1 0.0.0.0 MRU 1504 [Labels: implicit-null Exp: 0] 60 ms, ret code 6
! 3 172.20.40.1 48 ms
Examples: IPv6 VPN over MPLS VRF
Examples: VRF Information
The following entries show VRF information for 6VPE.
The following is sample output from a Cisco Express Forwarding FIB associated with a virtual routing and forwarding (VRF) instance named cisco1:
Device# show ipv6 cef vrf cisco1 2001:8::/64 attached to GigabitEthernet0/0/1 2001:8::3/128 receive 2002:8::/64 nexthop 10.1.1.2 GigabitEthernet0/1/0 label 22 19 2010::/64 nexthop 2001:8::1 GigabitEthernet0/0/1 2012::/64 attached to Loopback1 2012::1/128 receive
The following is sample output regarding an IPv6 routing table associated with a VRF named cisco1:
Device# show ipv6 route vrf cisco1
IPv6 Routing Table cisco1 - 6 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
C 2001:8::/64 [0/0]
via ::, GigabitEthernet0/0/1
L 2001:8::3/128 [0/0]
via ::, GigabitEthernet0/0/1
B 2002:8::/64 [200/0]
via ::FFFF:192.168.1.4,
B 2010::/64 [20/1]
via 2001:8::1,
C 2012::/64 [0/0]
via ::, Loopback1
L 2012::1/128 [0/0]
via ::, Loopback1
Example: IPv6 VPN Configuration Using IPv4 Next Hop
The following example illustrates a 6VPE next hop:
interface Loopback0 ip address 192.168.2.11 255.255.255.255 ! router bgp 100 neighbor 192.168.2.10 remote-as 100 neighbor 192.168.2.10 update-source Loopback0 ! address-family vpnv6 neighbor 192.168.2.10 activate neighbor 192.168.2.10 send-community extended exit-address-family
By default, the next hop advertised will be the IPv6 Virtual Private Network (VPN) address:
[0:0]::FFFF:192.168.2.10
Note that it is a 192-bit address in the format of [RD]::FFFF:IPv4-address.
When the Border Gateway Protocol (BGP) IPv6 VPN peers share a common subnet, the MP_REACH_NLRI attribute contains a link-local address next hop in addition to the global address next hop. This situation typically occurs in an interautonomous-system topology when autonomous system boundary routers (ASBRs) are facing each other. In that case, the link-local next hop is used locally, and the global next hop is readvertised by BGP.
The BGP next hop is the keystone for building the label stack. The inner label is obtained from the BGP network layer reachability information (NLRI), and the outer label is the Label Distribution Protocol (LDP) label to reach the IPv4 address embedded into the BGP next hop.
Additional References
Related Documents
Related Topic |
Document Title |
|---|---|
|
Cisco IOS commands |
|
|
IPv6 addressing and connectivity |
IPv6 Configuration Guide Library |
|
IPv6 commands |
|
|
Cisco IOS IPv6 features |
|
|
Configuring MPLS Layer 3 VPNs |
"MPLS Virtual Private Networks" module in the MPLS Layer 3 VPNs Configuration Guide |
Standards and RFCs
Standard/RFC |
Title |
|---|---|
|
RFCs for IPv6 |
Technical Assistance
Description |
Link |
|---|---|
|
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. |
Feature Information for IPv6 VPN over MPLS
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Feature Name |
Releases |
Feature Information |
|---|---|---|
|
IPv6 VPN over MPLS (6VPE) |
12.2(28)SB 12.2(33)SRB 12.2(33)SXI 12.4(20)T 15.0(1)S Cisco IOS XE Release 3.1S Cisco IOS XE Release 3.6S |
The IPv6 VPN (6VPE) over a MPLS IPv4 core infrastructure feature allows ISPs to offer IPv6 VPN services to their customers. In Cisco IOS Release 12.2(28)SB, this feature was introduced. In Cisco IOS Releases 12.2(33)SRB, 12.2(33)SXI, 12.4(20)T, and 15.0(1)S, this feature was integrated. In Cisco IOS XE Release 3.1S, this feature was implemented on the Cisco ASR 1000 Series Aggregation Services Router. In Cisco IOS XE Release 3.6S, support was added for the Cisco ASR 903 Router. The following commands were introduced or modified: aggregate-address, address-family ipv6, address-family vpnv6, ipv6 route, mls ipv6 vrf, neighbor activate, neighbor ebgp-multihop, neighbor next-hop-unchanged, neighbor remote-as, neighbor route-reflector-client, neighbor send-community, neighbor send-label, neighbor update-source, network, rd, router bgp, route-target, vrf definition, vrf forwarding. |
|
IPv6 VPN over MPLS (6VPE) InterAS Options |
12.2(33)SB2 Cisco IOS XE Release 3.1S |
IPv6 supports this feature. |
Glossary
- 6VPE device—Provider edge device providing BGP-MPLS IPv6 VPN service over an IPv4-based MPLS core. It is a IPv6 VPN PE, dual-stack device that implements 6PE concepts on the core-facing interfaces.
- customer edge (CE) device—A service provider device that connects to VPN customer sites.
- Forwarding Information Base (FIB)—Table containing the information necessary to forward IP datagrams. At a minimum, the FIB contains the interface identifier and next-hop information for each reachable destination network prefix.
- inbound route filtering (IRF)—A BGP capability used for filtering incoming BGP updates that are not to be imported by the receiving PE device.
- IPv6 provider edge device (6PE device)—Device running a BGP-based mechanism to interconnect IPv6 islands over an MPLS-enabled IPv4 cloud.
- IPv6 VPN address—A IPv6 VPN address is a 24-byte identifier, beginning with an 8-byte route distinguisher (RD) and ending with a 16-byte IPv6 address. Sometimes it is called an IPv6 VPN address.
- IPv6 VPN address family—The address-family identifier (AFI) identifies a particular network-layer protocol and the subsequent AFI (SAFI) provides additional information. The AFI IPv6 SAFI VPN (AFI=2, SAFI=128) is called the IPv6 VPN address family. Sometimes it is called the IPv6 VPN address family. Similarly AFI IPv4 SAFI VPN is the VPNv4 address family.
- network layer reachability information (NLRI)—BGP sends routing update messages containing NLRI to describe a route and how to get there. In this context, an NLRI is a prefix. A BGP update message carries one or more NLRI prefixes and the attributes of a route for the NLRI prefixes; the route attributes include a BGP next hop gateway address and community values.
- outbound route filtering (ORF)—A BGP capability used to filtering outgoing BGP routing updates.
- point of presence (POP)—Physical location where an interexchange carrier installed equipment to interconnect with a local exchange carrier.
- provider edge (PE) device—A service provider device connected to VPN customer sites.
- route distinguisher (RD)—A 64-bit value prepended to an IPv6 prefix to create a globally unique IPv6 VPN address.
- Routing Information Base (RIB)—Also called the routing table.
- Virtual routing and forwarding (VRF)—A VPN routing and forwarding instance in a PE.
- VRF table—A routing and a forwarding table associated to a VRF. This is a customer-specific table that enables the PE device to maintain independent routing states for each customer.