The following example shows how to configure two CLI views, “first” and “second". Thereafter, you can verify the CLI view in the running configuration.

Device(config)# parser view first inclusive
Device(config-view)# secret 5 firstpass
Device(config-view)# command exec exclude show version
Device(config-view)# command exec exclude configure terminal
Device(config-view)# command exec exclude all show ip
Device(config-view)# exit
Device(config)# parser view second
Device(config-view)# secret 5 secondpass
Device(config-view)# command exec include-exclusive show ip interface
Device(config-view)# command exec include logout
Device(config-view)# exit
!
!
Device(config-view)# do show running-config | beg view

parser view first inclusive
 secret 5 $1$MCmh$QuZaU8PIMPlff9sFCZvgW/
 commands exec exclude configure terminal
 commands exec exclude configure
 commands exec exclude all show ip
 commands exec exclude show version
 commands exec exclude show
!
parser view second 
 secret 5 $1$iP2M$R16BXKecMEiQesxLyqygW.
 commands exec include-exclusive show ip interface
 commands exec include show ip
 commands exec include show
 commands exec include logout
!

After you have configured the CLI views “first” and “second", you can issue the enable viewcommand to verify which commands are available in each view. The following example shows which commands are available inside the CLI view “first” after the user has logged into this view. (Because the show ip command is configured with the all option, a complete set of suboptions is shown, except the show ip interface command, which is using the include-exclusive keyword in the second view.)

Device# enable view first
Password:
Device# ?
Exec commands:
  configure  Enter configuration mode
  enable     Turn on privileged commands
  exit       Exit from the EXEC
  show       Show running system information
Device# show ?
  ip       IP information
  parser   Display parser information
  version  System hardware and software status
Device# show ip ?
 
  access-lists            List IP access lists
  accounting              The active IP accounting database
  aliases                 IP alias table
  arp                     IP ARP table
  as-path-access-list     List AS path access lists
  bgp                     BGP information
  cache                   IP fast-switching route cache
  casa                    display casa information
  cef                     Cisco Express Forwarding
  community-list          List community-list
  dfp                     DFP information
  dhcp                    Show items in the DHCP database
  drp                     Director response protocol
  dvmrp                   DVMRP information
  eigrp                   IP-EIGRP show commands
  extcommunity-list       List extended-community list
  flow                    NetFlow switching
  helper-address          helper-address table
  http                    HTTP information
  igmp                    IGMP information
  irdp                    ICMP Device Discovery Protocol
.
.
.

The following example shows how to configure a lawful intercept view, add users to the view, and verify the users that were added:

!Initialize the LI-View.
Device(config)# li-view lipass user li_admin password li_adminpass
Device(config)# end
! Enter the LI-View; that is, check to see what commands are available within the view.
Device# enable view li-view
Password:
Device# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Device(config)# parser view li-view
 
Device(config-view)# ?
View commands:
  commands  Configure commands for a view
  default   Set a command to its defaults
  exit      Exit from view configuration mode
  name      New LI-View name      
  no        Negate a command or set its defaults
  password  Set a password associated with CLI views
Device(config-view)#
! NOTE:LI View configurations are never shown as part of ‘running-configuration’.
! Configure LI Users.
Device(config)# username lawful-intercept li-user1 password li-user1pass
 
Device(config)# username lawful-intercept li-user2 password li-user2pass
! Displaying LI User information.
Device# show users lawful-intercept
li_admin     
li-user1     
li-user2     
Device#

Note	The lawful intercept view is available only on specific images and the view name option is available only in the LI view.

The following sample output from the show running-config command shows that “view_one” and “view_two” have been added to superview “su_view1", “view_three”, and “view_four” have been added to superview “su_view2”:

Device# show running-config
!
parser view su_view1 superview
 secret 5 <encoded password>
 view view_one
 view view_two
!
parser view su_view2 superview
 secret 5 <encoded password>
 view view_three
 view view_four
!