Enabling Bidirectional SXP Support

The Bidirectional SXP Support feature enhances the functionality of Cisco TrustSec with SXP version 4 by adding support for Security Group Tag (SGT) Exchange Protocol (SXP) bindings that can be propagated in both directions between a speaker and a listener over a single connection.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for Bidirectional SXP Support

  • Ensure that Cisco TrustSec is configured on the device. For more information, see the “Cisco TrustSec Support for IOS” chapter in the Cisco TrustSec Configuration Guide.

Restrictions for Bidirectional SXP Support

  • The peers at each end of the connection must be configured as a bidirectional connection using the both keyword. It is a wrong configuration to have one end configured as a bidirectional connection using the both keyword and the other end configured as a speaker or listener (unidirectional connection).

Information About Bidirectional SXP Support

Bidirectional SXP Support Overview

Cisco TrustSec builds secure networks by establishing domains of trusted network devices. Each device in the domain is authenticated by its peers. The peer that produces data is the speaker and the corresponding peer is the listener.

With the support for bidirectional Security Group Tag (SGT) Exchange Protocol (SXP) configuration, a peer can act as both a speaker and a listener and propagate SXP bindings in both directions using a single connection.

The bidirectional SXP configuration is managed with one pair of IP addresses. On either end, only the listener initiates the SXP connection and the speaker accepts the incoming connection.

Figure 1. Bidirectional SXP Connection



In addition, SXP version 4 (SXPv4) continues to support the loop detection mechanism (to prevent stale binding in the network).

How to Enable Bidirectional SXP Support

Configuring Bidirectional SXP Support

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    cts sxp enable

    4.    cts sxp default password

    5.    cts sxp default source-ip

    6.    cts sxp connection peer ipv4-address {source | password} {default | none} mode {local | peer} both [vrf vrf-name]

    7.    cts sxp speaker hold-time minimum-period

    8.    cts sxp listener hold-time minimum-period maximum-period

    9.    exit


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example: 
    Device> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example: 
    Device# configure terminal
     

    Enters global configuration mode.

     
    Step 3 cts sxp enable


    Example: 
    Device(config)# cts sxp enable
     

    Enables the Cisco TrustSec Security Group Tag (SGT) Exchange Protocol version 4 (SXPv4) on a network device.

     
    Step 4 cts sxp default password


    Example: 
    Device(config)# cts sxp default password Cisco123
     

    (Optional) Specifies the Cisco TrustSec SGT SXP default password.

     
    Step 5 cts sxp default source-ip


    Example: 
    Device(config)# cts sxp default source-ip 10.20.2.2
     

    (Optional) Configures the Cisco TrustSec SGT SXP source IPv4 address.

     
    Step 6 cts sxp connection peer ipv4-address {source | password} {default | none} mode {local | peer} both [vrf vrf-name]


    Example: 
    Device(config)# cts sxp connection peer 10.20.2.2 password default mode local both
     

    Configures the Cisco TrustSec SXP peer address connection for a bidirectional SXP configuration. The both keyword configures the bidirectional SXP configuration.

    The source keyword specifies the IPv4 address of the source device. If no address is specified, the connection uses the default source address, if configured, or the address of the port.

    The password keyword specifies the password that Cisco TrustSec SXP uses for the connection using the following options:

    • default—Use the default Cisco TrustSec SXP password you configured using the cts sxp default password command.

    • none—A password is not used.

    The mode keyword specifies the role of the remote peer device:

    • local—The specified mode refers to the local device.

    • peer—The specified mode refers to the peer device.

    • both—Specifies that the device is both the speaker and the listener in the bidirectional SXP connection.

    The optional vrf keyword specifies the VRF to the peer. The default is the default VRF.

     
    Step 7 cts sxp speaker hold-time minimum-period


    Example: 
    Device(config)# cts sxp speaker hold-time 950
     

    (Optional) Configures the global hold time (in seconds) of a speaker network device for Cisco TrustSec SGT SXPv4. The valid range is from 1 to 65534. The default is 120.

     
    Step 8 cts sxp listener hold-time minimum-period maximum-period


    Example: 
    Device(config)# cts sxp listener hold-time 750 1500
     

    (Optional) Configures the global hold time (in seconds) of a listener network device for Cisco TrustSec SGT SXPv4. The valid range is from 1 to 65534. The default is 90 to 180.

    Note    The maximum-period value must be greater than or equal to the minimum-period value.
     
    Step 9 exit


    Example: 
    Device(config)# exit
     

    Exits global configuration mode.

     

    Verifying Bidirectional SXP Support Configuration

    SUMMARY STEPS

      1.    enable

      2.    show cts sxp {connections | sgt-map} [brief | vrf vrf-name]


    DETAILED STEPS
      Step 1   enable

      Enables privileged EXEC mode.

      • Enter your password if prompted.



      Example: 
      Device> enable

      Step 2   show cts sxp {connections | sgt-map} [brief | vrf vrf-name]

      Displays Cisco TrustSec Exchange Protocol (SXP) status and connections.



      Example: 

      Device# show cts sxp connections

SXP : Enabled
Highest Version Supported: 4
Default Password : Set
Default Source IP: Not Set
Connection retry open period: 120 secs
Reconcile period: 120 secs
Retry open timer is running
----------------------------------------------
Peer IP : 2.0.0.2
Source IP : 1.0.0.2
Conn status : On (Speaker) :: On (Listener)
Conn version : 4
Local mode : Both
Connection inst# : 1
TCP conn fd : 1(Speaker) 3(Listener)
TCP conn password: default SXP password
Duration since last state change: 1:03:38:03 (dd:hr:mm:sec) :: 0:00:00:46 (dd:hr:mm:sec)


      Device# show cts sxp connection brief

SXP : Enabled
Highest Version Supported: 4
Default Password : Set
Default Source IP: Not Set
Connection retry open period: 120 secs
Reconcile period: 120 secs
Retry open timer is running
-----------------------------------------------------
Peer_IP Source_IP Conn Status Duration
---------------------------------------------------
2.0.0.2 1.0.0.2 On(Speaker)::On(Listener) 0:00:37:17 (dd:hr:mm:sec)::0:00:37:19 (dd:hr:mm:sec)

      The following table describes the various scenarios for the connection status output.

      Table 1 Connection Status Output Scenarios
      Node1 Node2 Node1 CLI Output for Connection Status Node2 CLI Output for Connection Status
      Both Both

      On (Speaker)

      On (Listener)

      On (Speaker)

      On (Listener)

      Speaker Listener On On
      Listener Speaker On On

      Configuration Examples for Bidirectional SXP Support

      Example: Configuring Bidirectional SXP Support

      The following example shows how to enable bidirectional CTS-SXP and configure the SXP peer connection on Device_A to connect to Device_B: 

      Device_A> enable
Device_A# configure terminal
Device_A(config)# cts sxp enable
Device_A(config)# cts sxp default password Cisco123
Device_A(config)# cts sxp default source-ip 10.10.1.1
Device_A(config)# cts sxp connection peer 10.20.2.2 password default mode local both
Device_A(config)# exit

      The following example shows how to configure the bidirectional CTS-SXP peer connection on Device_B to connect to Device_A: 

      Device_B> enable
Device_B# configure terminal
Device_B(config)# cts sxp enable
Device_B(config)# cts sxp default password Password123
Device_B(config)# cts sxp default source-ip 10.20.2.2
Device_B(config)# cts sxp connection peer 10.10.1.1 password default mode local both
Device_B(config)# exit

      Additional References for Bidirectional SXP Support

      Related Documents

      Related Topic

      Document Title

      Cisco IOS commands

      Cisco IOS Master Command List, All Releases

      Security commands

      Cisco TrustSec configuration

      “Cisco TrustSec Support for IOS” chapter in the Cisco TrustSec Configuration Guide

      Technical Assistance

      Description Link

      The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

      To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

      Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

      http:/​/​www.cisco.com/​support

      Feature Information for Bidirectional SXP Support

      The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

      Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.
      Table 2 Feature Information for Bidirectional SXP Support

      Feature Name

      Releases

      Feature Information

      Bidirectional SXP Support

      Cisco IOS 15.2(2)E

      The Bidirectional SXP Support feature enhances the functionality of Cisco TrustSec with SXP version 4 by adding support for Security Group Tag (SGT) Exchange Protocol (SXP) bindings that can be propagated in both directions between a speaker and a listener over a single connection.

      In Cisco IOS Release 15.2(2)E, this feature is supported on the following platforms:

      • Cisco Catalyst 3750-X Series Switches

      • Cisco Catalyst 3560-X Series Switches

      The following command was introduced or modified: cts sxp connection peer.