- Cisco Unified Border Element Enterprise Protocol-Independent Features and Setup
- SIP INFO Method for DTMF Tone Generation
- DTMF Events through SIP Signaling
- Negotiation of an Audio Codec from a List of Codecs
- iLBC Support for SIP and H.323
- SIP Ability to Send a SIP Registration Message on a Border Element
- SIP Parameter Modification
- Session Refresh with Reinvites
- SIP Stack Portability
- Support for Software Media Termination Point
- Additional References
- Glossary
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Session Refresh with Reinvites
Configuring support for session refresh with reinvites expands the ability of the Cisco Unified Border Element to receive a REINVITE message that contains either a session refresh parameter or a change in media via a new SDP and ensure the session does not time out. The midcall-signaling command distinguishes between the way a Cisco Unified Communications Express and Cisco Unified Border Element releases signaling messages. Most SIP-to-SIP video and SIP-to-SIP ReInvite-based supplementary services features require the Configuring Session Refresh with Reinvites feature to be configured.
Cisco IOS Release 12.4(15)XZ and Earlier Releases
Session refresh support via OPTIONS method. For configuration information, see the "Enabling In-Dialog OPTIONS to Monitor Active SIP Sessions" section.
Cisco IOS Release 12.4(15)XZ and Later Releases
Cisco Unified BE transparently passes other session refresh messages and parameters so that UAs and proxies can establish keepalives on a call.
- The allow-connections sip to sip command must be configured before you configure the Session refresh with Reinvites feature. For more information and configuration steps see the "Configuring SIP-to-SIP Connections in a Cisco Unified Border Element" section.
Cisco Unified Border Element
- Cisco IOS Release 12.4(20)T or a later release must be installed and running on your Cisco Unified Border Element.
Cisco Unified Border Element (Enterprise)
- Cisco IOS XE Release 2.5 or a later release must be installed and running on your Cisco ASR 1000 Series Router.
DETAILED STEPS
| Command or Action | Purpose | |
|---|---|---|
|
|
Example: Router> enable |
Enables privileged EXEC mode.
|
|
|
Example: Router# configure terminal |
Enters global configuration mode. |
|
|
Example: Router(config)# voice service voip |
Enters VoIP voice-service configuration mode. |
|
|
Example: Router(conf-voi-serv)# sip |
Enters SIP configuration mode. |
|
|
Example: Router(conf-serv-sip)# midcall-signaling passthru |
Passes SIP messages from one IP leg to another IP leg. |
|
|
Example: Router(conf-serv-sip)# exit |
Exits the current mode. |
|
|
Example: Router(conf-serv-sip) end |
Returns to privileged EXEC mode. |
Feature Information for Session Refresh with Reinvites
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Feature History Table for the ASR
| Table 1 | Feature Information for Session Refresh with Reinvites |
| Feature Name |
Releases |
Feature Information |
|---|---|---|
| Session Refresh with Reinvites |
12.4(20)T |
Expands the ability of the Cisco Unified BE to control the session refresh parameters and ensure the session does not time out. midcall-signaling |
Feature History Table for the ISR
| Table 2 | Feature Information for Session Refresh with Reinvites |
| Feature Name |
Releases |
Feature Information |
|---|---|---|
| Session Refresh with Reinvites |
Cisco IOS XE Release 2.5 |
Expands the ability of the Cisco Unified BE to control the session refresh parameters and ensure the session does not time out. midcall-signaling |
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
Feedback