Contents

Configuring Multihop VPDN

Multihop virtual private dialup networking (VPDN) is a specialized VPDN configuration that allows packets to pass through multiple tunnels. Ordinarily, packets are not allowed to pass through more than one tunnel. In a multihop deployment, the VPDN tunnel is terminated after each hop and a new tunnel is initiated to the next hop destination.

Multihop VPDN deployments can also be used to configure a device as a tunnel switch. A tunnel switch acts as both a network access server (NAS) and a tunnel server, able to receive packets from an incoming VPDN tunnel and send them out over an outgoing VPDN tunnel. Tunnel switch configurations can be used between Internet service providers (ISPs) to provide wholesale VPDN services.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for Multihop VPDN

Before you configure multihop VPDN, a VPDN deployment must be configured. For more information about VPDN deployments that are compatible with multihop VPDN scenarios, see the Configuring a Multihop Tunnel Switch.

Restrictions for Multihop VPDN

Only the Layer 2 Tunneling Protocol (L2TP) is supported on the Cisco ASR 1000 Series Aggregation Services Routers.

Information About Multihop VPDN

Tunnel Switching Using Multihop VPDN

Multihop VPDN can be used to configure a device as a tunnel switch. A tunnel switch acts as both a NAS and a tunnel server, receiving packets from an incoming VPDN tunnel and sending them out over an outgoing VPDN tunnel. Tunnel switch configurations can be used between ISPs to provide wholesale VPDN services. A VPDN tunnel switch on the Cisco ASR 1000 Series Aggregation Services Routers can forward L2TP sessions. L2F or Point-to-Point Tunneling Protocol (PPTP) are not supported.

In an L2TP tunnel switching deployment, the tunnel endpoints are considered the originating NAS and the terminating tunnel server. The tunnel switch is not considered a tunnel endpoint.

The figure below shows a network scenario using a basic L2TP tunnel switching deployment.

Figure 1. Tunnel Switching Using Multihop VPDN

The tunnel switch can be configured to terminate incoming VPDN tunnels from multiple devices, and to initiate outgoing VPDN tunnels to one or more tunnel servers.

The Subscriber Service Switch (SSS) framework is supported for VPDN tunnel switching. SSS supports additional Layer 2 protocols, including PPP over Ethernet (PPPoE) and generic routing encapsulation (GRE). Configuring SSS for VPDN tunnel switching is optional. SSS profiles increase the scalability of tunnel switching configurations, particularly in multiprotocol environments.

How to Configure Multihop VPDN

Configuring a Multihop Tunnel Switch

Multihop VPDN can be used to configure a device as a tunnel switch. A tunnel switch acts as both a NAS and a tunnel server, and must be configured with both a NAS VPDN group and a tunnel server VPDN group.

Tunnel switching using the SSS infrastructure is supported. SSS allows L2TP, L2F, PPTP, PPPoE, PPPoA, GRE, and general packet radio service (GPRS) sessions to be switched over virtual links using a tunnel switch. SSS configurations are not required for tunnel switching data over L2TP, L2F, or PPTP tunnels, but SSS increases the scalability of tunnel switching deployments.


Note

On the Cisco ASR 1000 Series Aggregation Services Router, a multihop VPDN tunnel switch can be configured to forward L2TP tunnels only.

Perform these tasks to configure a device as a multihop VPDN tunnel switch:

Prerequisites for Configuring a Multihop Tunnel Switch

  • The tunnel endpoints must be configured for VPDN tunneling as described in the Configuring NAS-Initiated Dial-In VPDN Tunneling module.

  • If you want to perform VPDN tunnel authorization searches based on the multihop hostname, you must configure the search to use the multihop hostname as described in the Configuring AAA for VPDNs module.

Enabling Multihop VPDN on the Tunnel Switch

In tunnel switching deployments, packets must traverse multiple tunnels. Multihop VPDN must be enabled on the tunnel switch for the deployment to function.

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    vpdn multihop


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Router> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Router# configure terminal
     

    Enters global configuration mode.

     
    Step 3 vpdn multihop


    Example:
    Router(config)# vpdn multihop
     

    Enables VPDN multihop.

     
    What to Do Next

    You must perform the task in the Configuring the Multihop Tunnel Switch to Terminate Incoming VPDN Tunnels.

    Configuring the Multihop Tunnel Switch to Terminate Incoming VPDN Tunnels

    A tunnel switch must be configured as a tunnel server, allowing it to terminate incoming VPDN tunnels. You can configure a tunnel switch to terminate tunnels from multiple devices.

    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    vpdn-group name

      4.    description string

      5.    accept-dialin

      6.    protocol l2tp

      7.    virtual-template number

      8.    exit

      9.    terminate-from hostname host-name


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Router> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.

       
      Step 2 configure terminal


      Example:
      Router# configure terminal
       

      Enters global configuration mode.

       
      Step 3 vpdn-group name


      Example:
      Router(config)# vpdn-group 1
       

      Creates a VPDN group and to enters VPDN group configuration mode.

       
      Step 4 description string


      Example:
      Router(config-vpdn)# description myvpdngroup
       

      (Optional) Adds a description to a VPDN group.

       
      Step 5 accept-dialin


      Example:
      Router(config-vpdn)# accept-dialin
       

      Configures a tunnel switch to accept requests from a NAS to establish a tunnel, creates an accept-dialin VPDN subgroup, and enters VPDN accept dial-in subgroup configuration mode.

       
      Step 6 protocol l2tp


      Example:
      Router(config-vpdn-acc-in)# protocol l2tp
       

      Specifies the Layer 2 Tunneling Protocol that the VPDN group will use.

       
      Step 7 virtual-template number


      Example:
      Router(config-vpdn-acc-in)# virtual-template 1
       

      (Optional) Specifies which virtual template will be used to clone virtual access interfaces.

      This step is not required if the virtual access interface is not going to be cloned when a user connects.

       
      Step 8 exit


      Example:
      Router(config-vpdn-acc-in)# exit
       

      Exits to VPDN group configuration mode.

       
      Step 9 terminate-from hostname host-name


      Example:
      Router(config-vpdn)# terminate-from hostname NAS12
       

      Specifies the hostname of the remote NAS that will be required when accepting a VPDN tunnel.

       
      What to Do Next

      You must perform the task in the Configuring the Multihop Tunnel Switch to Initiate Outgoing VPDN Tunnels section.

      Configuring the Multihop Tunnel Switch to Initiate Outgoing VPDN Tunnels

      A tunnel switch must be configured as a NAS, allowing it to initiate outgoing VPDN tunnels. You can configure a tunnel switch to initiate tunnels to multiple devices.

      SUMMARY STEPS

        1.    enable

        2.    configure terminal

        3.    vpdn-group name

        4.    description string

        5.    request-dialin

        6.    protocol l2tp

        7.    Do one of the following:

        • domain domain-name
        • dnis {dnis-number | dnis-group-name}
        • multihop-hostname ingress-tunnel-name

        8.    exit

        9.    initiate-to ip ip-address [limit limit-number] [priority priority-number]


      DETAILED STEPS
         Command or ActionPurpose
        Step 1 enable


        Example:
        Router> enable
         

        Enables privileged EXEC mode.

        • Enter your password if prompted.

         
        Step 2 configure terminal


        Example:
        Router# configure terminal
         

        Enters global configuration mode.

         
        Step 3 vpdn-group name


        Example:
        Router(config)# vpdn-group 1
         

        Creates a VPDN group and enters VPDN group configuration mode.

         
        Step 4 description string


        Example:
        Router(config-vpdn)# description myvpdngroup
         

        (Optional) Adds a description to a VPDN group.

         
        Step 5 request-dialin


        Example:
        Router(config-vpdn)# request-dialin
         

        Configures a tunnel switch to request the establishment of a tunnel to a tunnel server, creates a request-dialin VPDN subgroup, and enters VPDN request dial-in subgroup configuration mode.

         
        Step 6 protocol l2tp


        Example:
        Router(config-vpdn-req-in)# protocol l2tp
         

        Specifies the Layer 2 Tunneling Protocol that the VPDN group will use.

         
        Step 7Do one of the following:
        • domain domain-name
        • dnis {dnis-number | dnis-group-name}
        • multihop-hostname ingress-tunnel-name


        Example:
        Router(config-vpdn-req-in)# domain company.com


        Example:
        Router(config-vpdn-req-in)# dnis 5687


        Example:
        Router(config-vpdn-req-in)# multihop-hostname nas1
         

        Requests that PPP calls from a specific domain name be tunneled.

        or

        Requests that PPP calls from a specific DNIS number or DNIS group be tunneled.

        or

        Enables the tunnel switch to initiate a tunnel based on the NAS host name or the ingress tunnel ID.

        Note   

        If you use the multihop-hostname command to configure your tunnel switch, you must configure vpdn search-order command with the multihop-hostname keyword. For more information on configuring the VPDN tunnel authorization search order, see the Configuring AAA for VPDNs module.

         
        Step 8 exit


        Example:
        Router(config-vpdn-req-in)# exit
         

        Exits to VPDN group configuration mode.

         
        Step 9 initiate-to ip ip-address [limit limit-number] [priority priority-number]


        Example:
        Router(config-vpdn)# initiate-to ip 10.1.1.1 limit 12
         

        Specifies an IP address that will be used for Layer 2 tunneling.

        • limit --Maximum number of connections that can be made to this IP address.

        • priority --Priority for this IP address.

        Note   

        The priority keyword is typically not configured on a tunnel switch. Information used for load balancing and failover is configured on a remote authentication, authorization, and accounting (AAA) server instead. For more information about configuring load balancing and failover priorities using a remote AAA server, see the Configuring AAA for VPDNs module.

        • Multiple tunnel servers can be configured on the tunnel switch by configuring multiple initiate-to commands.

         

        Configuration Examples for Multihop VPDN

        Example Configuring Multihop VPDN Tunnel Switching

        The following example configures a NAS, tunnel switch, and tunnel server to establish a multihop VPDN tunnel using L2TP:

        NAS Configuration

        ! Configure the NAS to initiate VPDN dial-in sessions to the tunnel switch
vpdn-group 1
 request-dialin
  protocol l2tp
  domain cisco.com
!
 initiate-to ip 172.22.66.25 
 local name ISP-NAS

        Tunnel Switch Configuration

        !Enable VPDN
vpdn enable
!
!Enable multihop
vpdn multihop
        !
        ! Configure the tunnel switch to use the multihop hostname in the authentication search.
         vpdn search-order multihop-hostname domain dnis
        !
        ! Configure the tunnel switch to accept dial-in sessions from the NAS
vpdn-group tunnelin
 accept-dialin
  protocol l2tp
  virtual-template 1 
!
 terminate-from hostname ISP-NAS
 local name ISP-Sw
!
! Configure the tunnel switch to initiate VPDN dial-in sessions to the tunnel server
vpdn-group tunnelout
 request-dialin
  protocol l2tp
  multihop-hostname ISP-NAS
!
 initiate-to ip 10.2.2.2
 local name ISP-Sw

        Tunnel Server Configuration

        ! Configure the tunnel server to accept dial-in sessions from the NAS
vpdn-group 1
 accept-dialin 
  protocol l2tp
  virtual-template 1 
! 
 terminate-from hostname ISP-Sw
 local name ENT-TS

        Where to Go Next

        You can perform any of the relevant optional tasks in the Configuring Additional VPDN Features and in the VPDN Tunnel Management modules.

        Additional References

        Related Documents

        Related Topic

        Document Title

        Cisco IOS commands

        Cisco IOS Master Commands List, All Releases

        VPDN commands

        Cisco IOS VPDN Command Reference

        VPDN technology overview

        VPDN Technology Overview

        Broadband access aggregation and DSL commands

        Cisco IOS Broadband Access Aggregation and DSL Command Reference

        Standards

        Standard

        Title

        No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

        --

        MIBs

        MIB

        MIBs Link

        No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

        To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:

        http:/​/​www.cisco.com/​go/​mibs

        RFCs

        RFC

        Title

        RFC 2661

        Layer Two Tunneling Protocol (L2TP)

        Technical Assistance

        Description

        Link

        The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

        http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

        Feature Information for Multihop VPDN

        The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

        Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to . An account on Cisco.com is not required.
        Table 1 Feature Information for Multihop VPDN

        Feature Name

        Software Releases

        Feature Configuration Information

        Multihop VPDN

        Cisco IOS XE Release 2.2

        This feature was introduced on Cisco ASR 1000 Series Routers.

        Multihop VPDN is a specialized VPDN configuration that allows packets to pass through multiple tunnels. Ordinarily, packets are not allowed to pass through more than one tunnel. In a multihop deployment, the VPDN tunnel is terminated after each hop and a new tunnel is initiated to the next hop destination.

        No commands were introduced or modified by this feature.

        Subscriber Service Switch

        Cisco IOS XE Release 2.2.1

        This feature provides flexibility on where and how many subscribers are connected to available services and how those services are defined. The primary focus of SSS is to direct PPP from one point to another using a Layer 2 subscriber policy. The policy will manage tunneling of PPP in a policy-based bridging fashion.

        The following VPDN commands were introduced or modified by this feature:

        multihop-hostname and vpdn search-order.

        Configuring Multihop VPDN

        Configuring Multihop VPDN

        Multihop virtual private dialup networking (VPDN) is a specialized VPDN configuration that allows packets to pass through multiple tunnels. Ordinarily, packets are not allowed to pass through more than one tunnel. In a multihop deployment, the VPDN tunnel is terminated after each hop and a new tunnel is initiated to the next hop destination.

        Multihop VPDN deployments can also be used to configure a device as a tunnel switch. A tunnel switch acts as both a network access server (NAS) and a tunnel server, able to receive packets from an incoming VPDN tunnel and send them out over an outgoing VPDN tunnel. Tunnel switch configurations can be used between Internet service providers (ISPs) to provide wholesale VPDN services.

        Finding Feature Information

        Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

        Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

        Prerequisites for Multihop VPDN

        Before you configure multihop VPDN, a VPDN deployment must be configured. For more information about VPDN deployments that are compatible with multihop VPDN scenarios, see the Configuring a Multihop Tunnel Switch.

        Restrictions for Multihop VPDN

        Only the Layer 2 Tunneling Protocol (L2TP) is supported on the Cisco ASR 1000 Series Aggregation Services Routers.

        Information About Multihop VPDN

        Tunnel Switching Using Multihop VPDN

        Multihop VPDN can be used to configure a device as a tunnel switch. A tunnel switch acts as both a NAS and a tunnel server, receiving packets from an incoming VPDN tunnel and sending them out over an outgoing VPDN tunnel. Tunnel switch configurations can be used between ISPs to provide wholesale VPDN services. A VPDN tunnel switch on the Cisco ASR 1000 Series Aggregation Services Routers can forward L2TP sessions. L2F or Point-to-Point Tunneling Protocol (PPTP) are not supported.

        In an L2TP tunnel switching deployment, the tunnel endpoints are considered the originating NAS and the terminating tunnel server. The tunnel switch is not considered a tunnel endpoint.

        The figure below shows a network scenario using a basic L2TP tunnel switching deployment.

        Figure 1. Tunnel Switching Using Multihop VPDN

        The tunnel switch can be configured to terminate incoming VPDN tunnels from multiple devices, and to initiate outgoing VPDN tunnels to one or more tunnel servers.

        The Subscriber Service Switch (SSS) framework is supported for VPDN tunnel switching. SSS supports additional Layer 2 protocols, including PPP over Ethernet (PPPoE) and generic routing encapsulation (GRE). Configuring SSS for VPDN tunnel switching is optional. SSS profiles increase the scalability of tunnel switching configurations, particularly in multiprotocol environments.

        How to Configure Multihop VPDN

        Configuring a Multihop Tunnel Switch

        Multihop VPDN can be used to configure a device as a tunnel switch. A tunnel switch acts as both a NAS and a tunnel server, and must be configured with both a NAS VPDN group and a tunnel server VPDN group.

        Tunnel switching using the SSS infrastructure is supported. SSS allows L2TP, L2F, PPTP, PPPoE, PPPoA, GRE, and general packet radio service (GPRS) sessions to be switched over virtual links using a tunnel switch. SSS configurations are not required for tunnel switching data over L2TP, L2F, or PPTP tunnels, but SSS increases the scalability of tunnel switching deployments.


        Note

        On the Cisco ASR 1000 Series Aggregation Services Router, a multihop VPDN tunnel switch can be configured to forward L2TP tunnels only.

        Perform these tasks to configure a device as a multihop VPDN tunnel switch:

        Prerequisites for Configuring a Multihop Tunnel Switch

        • The tunnel endpoints must be configured for VPDN tunneling as described in the Configuring NAS-Initiated Dial-In VPDN Tunneling module.

        • If you want to perform VPDN tunnel authorization searches based on the multihop hostname, you must configure the search to use the multihop hostname as described in the Configuring AAA for VPDNs module.

        Enabling Multihop VPDN on the Tunnel Switch

        In tunnel switching deployments, packets must traverse multiple tunnels. Multihop VPDN must be enabled on the tunnel switch for the deployment to function.

        SUMMARY STEPS

          1.    enable

          2.    configure terminal

          3.    vpdn multihop


        DETAILED STEPS
           Command or ActionPurpose
          Step 1 enable


          Example:
          Router> enable
           

          Enables privileged EXEC mode.

          • Enter your password if prompted.

           
          Step 2 configure terminal


          Example:
          Router# configure terminal
           

          Enters global configuration mode.

           
          Step 3 vpdn multihop


          Example:
          Router(config)# vpdn multihop
           

          Enables VPDN multihop.

           
          What to Do Next

          Configuring the Multihop Tunnel Switch to Terminate Incoming VPDN Tunnels

          A tunnel switch must be configured as a tunnel server, allowing it to terminate incoming VPDN tunnels. You can configure a tunnel switch to terminate tunnels from multiple devices.

          SUMMARY STEPS

            1.    enable

            2.    configure terminal

            3.    vpdn-group name

            4.    description string

            5.    accept-dialin

            6.    protocol l2tp

            7.    virtual-template number

            8.    exit

            9.    terminate-from hostname host-name


          DETAILED STEPS
             Command or ActionPurpose
            Step 1 enable


            Example:
            Router> enable
             

            Enables privileged EXEC mode.

            • Enter your password if prompted.

             
            Step 2 configure terminal


            Example:
            Router# configure terminal
             

            Enters global configuration mode.

             
            Step 3 vpdn-group name


            Example:
            Router(config)# vpdn-group 1
             

            Creates a VPDN group and to enters VPDN group configuration mode.

             
            Step 4 description string


            Example:
            Router(config-vpdn)# description myvpdngroup
             

            (Optional) Adds a description to a VPDN group.

             
            Step 5 accept-dialin


            Example:
            Router(config-vpdn)# accept-dialin
             

            Configures a tunnel switch to accept requests from a NAS to establish a tunnel, creates an accept-dialin VPDN subgroup, and enters VPDN accept dial-in subgroup configuration mode.

             
            Step 6 protocol l2tp


            Example:
            Router(config-vpdn-acc-in)# protocol l2tp
             

            Specifies the Layer 2 Tunneling Protocol that the VPDN group will use.

             
            Step 7 virtual-template number


            Example:
            Router(config-vpdn-acc-in)# virtual-template 1
             

            (Optional) Specifies which virtual template will be used to clone virtual access interfaces.

            This step is not required if the virtual access interface is not going to be cloned when a user connects.

             
            Step 8 exit


            Example:
            Router(config-vpdn-acc-in)# exit
             

            Exits to VPDN group configuration mode.

             
            Step 9 terminate-from hostname host-name


            Example:
            Router(config-vpdn)# terminate-from hostname NAS12
             

            Specifies the hostname of the remote NAS that will be required when accepting a VPDN tunnel.

             
            What to Do Next

            You must perform the task in the Configuring the Multihop Tunnel Switch to Initiate Outgoing VPDN Tunnels section.

            Configuring the Multihop Tunnel Switch to Initiate Outgoing VPDN Tunnels

            A tunnel switch must be configured as a NAS, allowing it to initiate outgoing VPDN tunnels. You can configure a tunnel switch to initiate tunnels to multiple devices.

            SUMMARY STEPS

              1.    enable

              2.    configure terminal

              3.    vpdn-group name

              4.    description string

              5.    request-dialin

              6.    protocol l2tp

              7.    Do one of the following:

              • domain domain-name
              • dnis {dnis-number | dnis-group-name}
              • multihop-hostname ingress-tunnel-name

              8.    exit

              9.    initiate-to ip ip-address [limit limit-number] [priority priority-number]


            DETAILED STEPS
               Command or ActionPurpose
              Step 1 enable


              Example:
              Router> enable
               

              Enables privileged EXEC mode.

              • Enter your password if prompted.

               
              Step 2 configure terminal


              Example:
              Router# configure terminal
               

              Enters global configuration mode.

               
              Step 3 vpdn-group name


              Example:
              Router(config)# vpdn-group 1
               

              Creates a VPDN group and enters VPDN group configuration mode.

               
              Step 4 description string


              Example:
              Router(config-vpdn)# description myvpdngroup
               

              (Optional) Adds a description to a VPDN group.

               
              Step 5 request-dialin


              Example:
              Router(config-vpdn)# request-dialin
               

              Configures a tunnel switch to request the establishment of a tunnel to a tunnel server, creates a request-dialin VPDN subgroup, and enters VPDN request dial-in subgroup configuration mode.

               
              Step 6 protocol l2tp


              Example:
              Router(config-vpdn-req-in)# protocol l2tp
               

              Specifies the Layer 2 Tunneling Protocol that the VPDN group will use.

               
              Step 7Do one of the following:
              • domain domain-name
              • dnis {dnis-number | dnis-group-name}
              • multihop-hostname ingress-tunnel-name


              Example:
              Router(config-vpdn-req-in)# domain company.com


              Example:
              Router(config-vpdn-req-in)# dnis 5687


              Example:
              Router(config-vpdn-req-in)# multihop-hostname nas1
               

              Requests that PPP calls from a specific domain name be tunneled.

              or

              Requests that PPP calls from a specific DNIS number or DNIS group be tunneled.

              or

              Enables the tunnel switch to initiate a tunnel based on the NAS host name or the ingress tunnel ID.

              Note   

              If you use the multihop-hostname command to configure your tunnel switch, you must configure vpdn search-order command with the multihop-hostname keyword. For more information on configuring the VPDN tunnel authorization search order, see the Configuring AAA for VPDNs module.

               
              Step 8 exit


              Example:
              Router(config-vpdn-req-in)# exit
               

              Exits to VPDN group configuration mode.

               
              Step 9 initiate-to ip ip-address [limit limit-number] [priority priority-number]


              Example:
              Router(config-vpdn)# initiate-to ip 10.1.1.1 limit 12
               

              Specifies an IP address that will be used for Layer 2 tunneling.

              • limit --Maximum number of connections that can be made to this IP address.

              • priority --Priority for this IP address.

              Note   

              The priority keyword is typically not configured on a tunnel switch. Information used for load balancing and failover is configured on a remote authentication, authorization, and accounting (AAA) server instead. For more information about configuring load balancing and failover priorities using a remote AAA server, see the Configuring AAA for VPDNs module.

              • Multiple tunnel servers can be configured on the tunnel switch by configuring multiple initiate-to commands.

               

              Configuration Examples for Multihop VPDN

              Example Configuring Multihop VPDN Tunnel Switching

              The following example configures a NAS, tunnel switch, and tunnel server to establish a multihop VPDN tunnel using L2TP:

              NAS Configuration

              ! Configure the NAS to initiate VPDN dial-in sessions to the tunnel switch
vpdn-group 1
 request-dialin
  protocol l2tp
  domain cisco.com
!
 initiate-to ip 172.22.66.25 
 local name ISP-NAS

              Tunnel Switch Configuration

              !Enable VPDN
vpdn enable
!
!Enable multihop
vpdn multihop
              !
              ! Configure the tunnel switch to use the multihop hostname in the authentication search.
               vpdn search-order multihop-hostname domain dnis
              !
              ! Configure the tunnel switch to accept dial-in sessions from the NAS
vpdn-group tunnelin
 accept-dialin
  protocol l2tp
  virtual-template 1 
!
 terminate-from hostname ISP-NAS
 local name ISP-Sw
!
! Configure the tunnel switch to initiate VPDN dial-in sessions to the tunnel server
vpdn-group tunnelout
 request-dialin
  protocol l2tp
  multihop-hostname ISP-NAS
!
 initiate-to ip 10.2.2.2
 local name ISP-Sw

              Tunnel Server Configuration

              ! Configure the tunnel server to accept dial-in sessions from the NAS
vpdn-group 1
 accept-dialin 
  protocol l2tp
  virtual-template 1 
! 
 terminate-from hostname ISP-Sw
 local name ENT-TS

              Where to Go Next

              You can perform any of the relevant optional tasks in the Configuring Additional VPDN Features and in the VPDN Tunnel Management modules.

              Additional References

              Related Documents

              Related Topic

              Document Title

              Cisco IOS commands

              Cisco IOS Master Commands List, All Releases

              VPDN commands

              Cisco IOS VPDN Command Reference

              VPDN technology overview

              VPDN Technology Overview

              Broadband access aggregation and DSL commands

              Cisco IOS Broadband Access Aggregation and DSL Command Reference

              Standards

              Standard

              Title

              No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

              --

              MIBs

              MIB

              MIBs Link

              No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

              To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:

              http:/​/​www.cisco.com/​go/​mibs

              RFCs

              RFC

              Title

              RFC 2661

              Layer Two Tunneling Protocol (L2TP)

              Technical Assistance

              Description

              Link

              The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

              http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

              Feature Information for Multihop VPDN

              The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

              Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to . An account on Cisco.com is not required.
              Table 1 Feature Information for Multihop VPDN

              Feature Name

              Software Releases

              Feature Configuration Information

              Multihop VPDN

              Cisco IOS XE Release 2.2

              This feature was introduced on Cisco ASR 1000 Series Routers.

              Multihop VPDN is a specialized VPDN configuration that allows packets to pass through multiple tunnels. Ordinarily, packets are not allowed to pass through more than one tunnel. In a multihop deployment, the VPDN tunnel is terminated after each hop and a new tunnel is initiated to the next hop destination.

              No commands were introduced or modified by this feature.

              Subscriber Service Switch

              Cisco IOS XE Release 2.2.1

              This feature provides flexibility on where and how many subscribers are connected to available services and how those services are defined. The primary focus of SSS is to direct PPP from one point to another using a Layer 2 subscriber policy. The policy will manage tunneling of PPP in a policy-based bridging fashion.

              The following VPDN commands were introduced or modified by this feature:

              multihop-hostname and vpdn search-order.