Cisco IOS Release 12.2SX System Message Guide

CONST_V6 Messages
- CONST_V6-5
CONTROLLER Messages
COPTMONMIB Messages
- COPTMONMIB-3
Cougar Messages
CPU_INTF_FPGA Messages
- CPU_INTF_FPGA-2
- CPU_INTF_FPGA-3
- CPU_INTF_FPGA-4
- CPU_INTF_FPGA-5
CPU_MONITOR Messages
- CPU_MONITOR-2
- CPU_MONITOR-3
- CPU_MONITOR-6
CRYPTO Messages
- CRYPTO-3
- CRYPTO-4
- CRYPTO-5
- CRYPTO-6
CRYPTO_HA Messages
- CRYPTO_HA-3
- CRYPTO_HA-6
CRYPTO_HA_IKE Messages
- CRYPTO_HA_IKE-3
- CRYPTO_HA_IKE-4
CRYPTO_HA_IPSEC Messages
- CRYPTO_HA_IPSEC-3
- CRYPTO_HA_IPSEC-4
CRYPTO_RSA_ISSU Messages
- CRYPTO_RSA_ISSU-3
CSG Messages
- CSG-3
- CSG-4
- CSG-6
CSM_SLB Messages
- CSM_SLB-4
CT3 Messages
CTS Messages
- CTS-0
- CTS-1
- CTS-2
- CTS-3
- CTS-4
- CTS-5
- CTS-6
- CTS-7
CTS_HA Messages
- CTS_HA-3
CTS_HA_ISSU Messages
- CTS_HA_ISSU-3
- CTS_HA_ISSU-6
CWAN_ALARM Messages
- CWAN_ALARM-6
CWAN_ATM Messages
- CWAN_ATM-3
- CWAN_ATM-5
CWAN_ATOM-HA Messages
- CWAN_ATOM-HA-2
- CWAN_ATOM-HA-3
CWAN_CHOC Messages
- CWAN_CHOC-4
CWAN_CHOC_DSX Messages
- CWAN_CHOC_DSX-3
CWAN_CT3 Messages
- CWAN_CT3-3
CWAN_FWD_TABLES Messages
- CWAN_FWD_TABLES-3
CWAN_HA Messages
- CWAN_HA-2
- CWAN_HA-3
- CWAN_HA-4
CWAN_HAL Messages
- CWAN_HAL-3
- CWAN_HAL-4
CWAN_IFMGR Messages
- CWAN_IFMGR-4
CWANLC Messages
- CWANLC-3
- CWANLC-5
CWANLC_ATM Messages
- CWANLC_ATM-3
CWAN_POSEIDON Messages
CWAN_QINQ Messages
- CWAN_QINQ-3
CWAN_RP Messages
- CWAN_RP-0
- CWAN_RP-1
- CWAN_RP-2
- CWAN_RP-3
- CWAN_RP-4
- CWAN_RP-5
- CWAN_RP-6
- CWAN_RP-7
CWAN_SLOT Messages
- CWAN_SLOT-1
CWAN_SP Messages
- CWAN_SP-3
- CWAN_SP-4
CWAN_SPA Messages
CWPA Messages
- CWPA-2
- CWPA-3
- CWPA-4
CWPABRIDGE Messages
CWRPSPA Messages
- CWRPSPA-3
- CWRPSPA-4
- CWRPSPA-6
CWSLC Messages
- CWSLC-3
CWTLC Messages
- CWTLC-0
- CWTLC-2
- CWTLC-3
- CWTLC-4
- CWTLC-5
- CWTLC-6
CWTLC_ATOM Messages
- CWTLC_ATOM-3
CWTLC_CHOC Messages
- CWTLC_CHOC-3
CWTLC_CHOC_DSX Messages
CWTLC_CHOCX Messages
- CWTLC_CHOCX-3
CWTLC_GEWAN Messages
- CWTLC_GEWAN-3
CWTLC_GEWAN-5
CWTLC_QOS Messages
CWTLC_RP Messages
- CWTLC_RP-3

CONST_V6 Messages

This section contains IP version 6 (CONST_V6) messages.

CONST_V6-5

Error Message    %CONST_V6-5-FIB_EXCEP_OFF: Protocol IPv6 recovered from FIB exception

Explanation The IPv6 CEF table successfully reloaded to the hardware FIB TCAM. All IPv6 packets will be switched by the hardware.

Recommended Action No action is required.

Error Message    %CONST_V6-5-FIB_EXCEP_ON: Failed to insert an IPv6 prefix in hardware 
FIB TCAM

Explanation The switch failed to insert an IPv6 entry into the hardware FIB TCAM because the total number of software-forwarding entries exceeded the hardware FIB TCAM limit. Some IPv6 packets might be switched by the software.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

CONTROLLER Messages

This section contains controller messages.

Error Message    %CONTROLLER-5-DOWNDETAIL: Controller [chars], changed state to [chars] 
due to [chars]

Explanation A configurable controller has changed its state.

Recommended Action This is an informational message only. No action is required.

Error Message    %CONTROLLER-3-INBAND_BAD_PAK: Possibly un-encapsulated packet passed 
to Mistral: int [chars], type [int], stat [hex], flags [hex], size [dec], offset 
[dec], total [int]

Explanation A badly encapsulated packet was received from the process level.

Recommended Action If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CONTROLLER-3-INBAND_INVALID_IBL_FILL: Attempting to issue IBL Fill 
when IBL is void of packet.

Explanation The input buffer logic (IBL) did not contain any packets. An IBL fill operation was attempted.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CONTROLLER-3-MISTRAL_INVALID_OBL_PAGE_REQUEST: Invalid request for 
free 'Output Buffer Logic' pages = [dec]

Explanation There was an invalid output buffer logic (OBL) page request. The maximum number of OBL pages has been set to its maximum value of 40 and processing will continue through the normal switching path.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CONTROLLER-3-NO_GIG_SYNC: Inband Gig interface not syncronized, 
status [hex]

Explanation The hardware for transmitting and receiving packets from and to the router is not functioning properly.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CONTROLLER-3-NO_OBL_TO_INBAND: The System Controller OBL to INBAND 
semaphore not obtained.

Explanation The system controller output buffer logic (OBL) to inband semaphore could not be properly obtained.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CONTROLLER-3-NO_SYSTEM_CONTROLLER_INIT_STATUS: The System Controller 
init status of 0xf not obtained, status [hex]

Explanation The system controller initialization status could not be properly obtained.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CONTROLLER-3-NOT_IDLE: Receive path not idle after the reset.

Explanation The receiving hardware is not idle after it has been reset.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CONTROLLER-3-SYSTEM_CONTROLLER_BUSY: The System Controller could not 
finish [chars] operation in time.

Explanation The system controller failed in completing its operation.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CONTROLLER-3-TOOBIG: An attempt made to send giant packet on [chars] 
([dec] bytes from [hex], max allowed [dec])

Explanation An attempt was made to send an oversized packet.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CONTROLLER-5-UPDOWN_BERT: BERT test [chars] on Controller [chars]. 
Forced state to [chars]

Explanation A configurable controller has changed its state.

Recommended Action This is an informational message only. No action is required.

COPTMONMIB Messages

This section contains Cisco Optical Monitoring MIB (COPTMINMIB) messages.

COPTMONMIB-3

Error Message    %COPTMONMIB-3-ENTRYADDFAILED: Registering of the interface with 
ifIndex [dec] to local data structure failed

Explanation An attempt to make an entry for the registering interface failed.

Error Message    %COPTMONMIB-3-ENTRYPRESENT: An entry is already present for the 
registering interface with ifIndex [dec]

Explanation An entry in the OPTICAL MONITORING MIB already exists for the registering interface.

Recommended Action No action is required.

Cougar Messages

This section contains Cougar line card messages.

Error Message    %COUGAR_EHSA-3-NCLK_FUNCVER_MISMATCH: Mismatch in the Network Clock 
Module Functional Version number. The Functional Version of the Network clock 
module in the Primary = [dec].[dec]

Explanation This may lead to loss of Network Clocking functionality if and when a CPU switchover occurs. The system is now running CONDITIONALLY REDUNDANT - subject to the above mentioned restriction

Error Message    No action required.%COUGAR_EHSA-3-TWO_PRIM_DETECT: Other RP has declared 
PRIMARY, two primaries active in chassis. This RP will now crash to avoid this 
condition.

Explanation N/A

Recommended Action No action required.

CPU_INTF_FPGA Messages

This section contains CPU interface field programmable gate array (FPGA) messages.

CPU_INTF_FPGA-2

Error Message    %CPU_INTF_FPGA-2-DEV_INIT_FAILURE: The CPU Interface FPGA 
initialization failed due to [chars]

Explanation The CPU interface FPGA initialization was not successful due to a hardware problem. This condition will cause packet drops.

Error Message    %CPU_INTF_FPGA-2-INT: [chars]

Explanation A fatal interrupt has occurred and the device has been reinitialized.

Error Message    %CPU_INTF_FPGA-2-NULL_DEV_OBJECT: The CPU Interface FPGA device object 
pointer is set to NULL

Explanation The memory location of the CPU Interface FPGA device object is invalid. The CPU interface FPGA operation is disabled and the device interrupt is now masked.

CPU_INTF_FPGA-3

Error Message    %CPU_INTF_FPGA-3-DEV_UNPAUSE_FAIL: Status register is [hex]

Explanation An attempt to unpause traffic from the CPU interface FPGA to the backplane interface ASIC has timed out. This failure may lead to traffic disruption.

Recommended Action If normal traffic processing does not resume, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CPU_INTF_FPGA-3-QUEUE_ALLOC_FAILED: Failed to allocate queue in the 
CPU Interface FPGA for 	SPA in bay ([dec])

Explanation Failed to allocate a queue for the SPA in the given bay. This failure may lead to traffic disruption.

CPU_INTF_FPGA-4

Error Message    %CPU_INTF_FPGA-4-DEV_WARN_INT: [chars]

Explanation The CPU interface FPGA received a nonfatal interrupt. This event should not affect the normal operation of the device.

Recommended Action No action is required.

CPU_INTF_FPGA-5

Error Message    %CPU_INTF_FPGA-5-PAUSE_FAIL: FPGA status register is [hex]

Explanation An attempt to pause traffic from the CPU interface FPGA to the backplane interface ASIC has timed out. This event may lead to traffic disruption.

CPU_MONITOR Messages

This section contains CPU monitor (CPU_MONITOR) messages.

CPU_MONITOR-2

Error Message    %CPU_MONITOR-2-NOT_RUNNING:  CPU_MONITOR messages have not been sent 
for [dec] seconds [[chars] [dec]%/[dec]% ([time-stamp] [dec]%/[dec]%)] [[chars] 
[time-stamp]] [[chars] [time-stamp]] [[chars] [time-stamp]]

Explanation CPU monitor messages have not been detected for a significant amount of time. A timeout is likely to occur soon, which will reset the system.

Recommended Action No action is required.

Error Message    %CPU_MONITOR-2-NOT_RUNNING_TB: CPU_MONITOR traceback: [hex] [hex] 
[hex] [hex] [hex] [hex] [hex] [hex]

Explanation This message provides additional debugging information for the NOT_RUNNING message. The message displays the traceback of the interrupted functions.

Recommended Action No action is required.

CPU_MONITOR-3

Error Message    %CPU_MONITOR-3-KERNEL_OPERATION: CPU_MONITOR kernel operation failed: 
[chars]

Explanation A CPU_MONITOR kernel operation required to identify supect threads has failed.

Recommended Action This is an informational message only. No action is required.

Error Message    %CPU_MONITOR-3-PEER_EXCEPTION: CPU_MONITOR peer has failed due to 
exception , resetting [[dec]/[dec]]

Explanation The CPU monitor messages failed on the peer processor. The system is no longer operational.

Recommended Action No action is required.

Error Message    %CPU_MONITOR-3-PEER_FAILED: CPU_MONITOR peer process has failed to 
receive heartbeats, reset by [%d/%d]

Explanation The CPU monitor messages have failed on the peer process and the system is no longer operational.

Recommended Action No action is required.

Error Message    %CPU_MONITOR-3-TIMED_OUT: CPU_MONITOR messages have failed, resetting 
%s [%d/%d]

Explanation The CPU monitor messages failed and the system is no longer operational.

Recommended Action No action is required.

CPU_MONITOR-6

Error Message    %CPU_MONITOR-6-NOT_HEARD: CPU_MONITOR messages have not been heard for 
%d seconds [%d/%d]

Explanation CPU monitor messages have not been detected for a significant amount of time. [dec] is the number of seconds. A timeout is likely to occur soon, which will reset the system. This error can be caused by a badly seated module or by high traffic in the EOBC channel.

Recommended Action Verify that all modules are seated properly in the chassis. Pull out the module mentioned in the message and inspect the backplane and module for bent pins or hardware damage. If the message persists after reseating all the modules, a hardware problem may exist, such as a defective module or chassis.

CRYPTO Messages

This section contains encryption (CRYPTO) messages.

CRYPTO-3

Error Message    %CRYPTO-3-CONNID_ALLOC_FAIL: Crypto engine failed to allocate a 
connection ID for negotiation from [IP_address] to [IP_address]

Explanation The crypto engine has exhausted all available connection IDs or is otherwise malfunctioning.

Recommended Action Decrease the number of concurrent connections or inspect the crypto engine.

Error Message    %CRYPTO-3-CRYPTO_INV_ACL: Crypto ACL with GT/LT/NEQ operator is not 
supported.

Explanation Crypto map ACL is an invalid map.

Recommended Action Remove the invalid ACL .

Error Message    %CRYPTO-3-ENGINE_BAD_ID: Crypto Engine id [dec] is invalid

Explanation The engine ID of the packet is set to something other than software crypto or hardware crypto. The system cannot determine which encryption (crypto) engine to use. The packet will be sent to the default crypto engine, which is the software crypto engine.

Recommended Action No action is required.

Error Message    %CRYPTO-3-EZVPN_VINTERFACE_CREATE_ERR: EZVPN([chars]): Virtual-access 
interface creation failed

Explanation The virtual interface feature will not work without a virtual access interface. The EZVPN configuration is unusable. You can remove the virtual interface configuration from EZVPN as a workaround.

Error Message    %CRYPTO-3-IKMP_QUERY_KEY: Querying key pair failed.

Explanation Querying public key and private key usinga subject name failed.

Recommended Action Check the subject name in the certificate.

Error Message    %CRYPTO-3-MTREE_CMD_BLOCK: Mtree command [dec] was blocked from the 
the mtree process queue.

Explanation An attempt was made to enqueue a command to the crypto mtree manager process even though IPsec is currently operating in HAPX mode.

Error Message    %CRYPTO-3-RSA_SELFTEST_FAILED: Generated RSA key failed self test

Explanation An automatic test of the newly generated RSA key pair has failed and the RSA key has been automatically deleted.

Recommended Action Retry the operation and attempt to create another RSA key pair. If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CRYPTO-3-TOKENADMINLOCKEDOUT: Cryptographic Token [chars] 
Administrator PIN Locked due to too many unsuccessful login attempts

Explanation The cryptographic token has disabled the Admin PIN due to too many login failures .

Recommended Action If the user PIN is also locked out, it will be necessary to reinitialize the card. The data on the card will be lost.

Error Message    %CRYPTO-3-TOKENADMINLOGINFAILED: Cryptographic Token [chars] ADMIN 
Login FAILED

Explanation The cryptographic token has rejected the administrator PIN offered by the router.

Recommended Action Enter the crypto pki token admin-pin command to enter the correct PIN.

Error Message     %CRYPTO-3-TOKENAPIFAILURE: Cryptographic Token [chars] API FAILED, 
error = [dec]

Explanation The cryptographic token returned an unexpected error.

Error Message    %CRYPTO-3-TOKENCHANGEPINFAILED: Cryptographic Token [chars] Change PIN 
FAILED

Explanation The cryptographic token has rejected the new PIN offered by the router.

Recommended Action Be sure you are logged in to the token as administrator. Try a longer PIN.

Error Message    %CRYPTO-3-TOKENLOCKEDOUT: Cryptographic Token [chars] PIN Locked due 
to too many unsuccessful login attempts

Explanation The cryptographic token has disabled the user PIN due to too many login failures.

Recommended Action Enter the crypto pki token admin-pin command to enter the correct administrator PIN.

Error Message    %CRYPTO-3-TOKENLOGINFAILED: Cryptographic Token [chars] Login FAILED

Explanation The cryptographic token has rejected the PIN offered bythe router.

Recommended Action Enter the crypto pki token user-pin command to enter the correct PIN.

Error Message    %CRYPTO-3-TOKENSTOREKEYFAILED: Key [chars] store on Cryptographic 
Token [chars] Failed

Explanation An error occurred attempting to write a new key pair out to the cryptographic token.

Recommended Action Try logging in to the token. If the error persists, try logging in as administrator.

CRYPTO-4

Error Message    %CRYPTO-4-ENC_METHOD_NOT_SUPPORTED: Invalid encryption method for IKE 
policy [int]

Explanation The configured encryption method is not supported

Recommended Action Use any of the valid encryption methods for the ISAKMP policy.

Error Message    %CRYPTO-4-EZVPN_SA_LIMIT: [chars]

Explanation The maximum number of EZVPN tunnels that can be set up on the platform has been reached. Active SAs will not be terminated, but additional SAs can not be established until the number of existing SAs decreases.

Recommended Action No action is required.

Error Message    %CRYPTO-4-IA_CLEARTEXT: Unencrypted traffic [chars] [IP_address] 
because crypto optional is configured

Explanation Cleartext traffic is passing through an interface that is configured for encryption. This traffic is accepted because the router has the CRYPTO IPSEC OPTIONAL ENABLE setting, which allows such traffic.

Recommended Action If you did not intend to configure the crypto optional setting, reconfigure the system to turn it off.

Error Message    %CRYPTO-4-IA_ENABLE: Security warning: crypto ipsec optional is 
configured

Explanation The router has the CRYPTO IPSEC OPTIONAL setting enabled. This setting allows data that would normally be encrypted to be sent without encryption.

Recommended Action If you did not intend to configure the crypto optional setting, reconfigure the system to turn it off.

Error Message    %CRYPTO-4-IKE_DENY_SA_REQ: IKE denied an [chars] SA request from 
[chars] to [chars] due to [chars]

Explanation Call Admission Control is configured globally or at the IKE level on this device. As a result, an IKE SA request was denied due to the reason described in the error message.

Recommended Action Depending on the reason that the request was denied, either reduce the load on the system so that it can handle new IKE SA requests, or increase the maximum allowed IKE sessions if more are needed.

Error Message    %CRYPTO-4-IKE_QUICKMODE_BAD_CERT: encrypted connection attempted with 
a peer without the configured certificate attributes

Explanation An encrypting peer attempted to establish an IPsec session with an interface for which it was not authorized. This condition might be considered to be a hostile event.

Recommended Action Verify that the peer is authorized to establish an IPsec session with the interface. If the peer is authorized, this condition might be caused by an incorrect configuration. Contact the administrator of the peer.

Error Message    %CRYPTO-4-IKE_SA_LIMIT: IKE active SA count is [int] but SA limit has 
been set to [int].

Explanation The IKE SA limit that was set is less than the number of active IKE SAs. Active SAs will not be terminated but no additional IKE SAs can be established unless the limit is increased or the number of active SAs decreases.

Recommended Action Increase the IKE SA limit if necessary to establish connectivity.

Error Message     %CRYPTO-4-IKE_SA_NEGO_LIMIT: IKE in-negotiation SA count currently is 
[int] but new limit has been set to [int].

Explanation The IKE in-negotiation SA limit that was set is less than the current number of in-negotiation IKE SA. As of a result, no more new IKE SAs can be created. However, those already in negotiation are allowed to finish.

Recommended Action Increase the IKE SA limit if necessary to establish connectivity.

Error Message    %CRYPTO-4-IKMP_ISR_LIMIT_MAX: INV SPI RECOV LIMIT [dec] maxed 
[IP_address] [IP_address]

Explanation The maximum limit of INVALID SPI RECOVERY SAs has been reached.

Recommended Action You may need to reload the local system.

Error Message    %CRYPTO-4-IPSEC_AAA_START_FAILURE: IPSEC Accounting was unable to send 
start record

Explanation The AAA subsystem was unable to send the accounting start record on behalf of IPsec. This condition can occur if the AAA server is unreachable.

Recommended Action Ensure that the AAA server is reachable and enabled for accounting.

Error Message    %CRYPTO-4-IPSEC_AAA_STOP_FAILURE: IPSEC Accounting was unable to send 
stop record

Explanation The AAA subsystem was unable to send the accounting stop record on behalf of IPsec. This condition can occur if the AAA server is unreachable.

Recommended Action Ensure that the AAA server is reachable and enabled for accounting.

Error Message    %CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED: Transform [chars] not valid 
under IPSec transform [chars]

Explanation The configured encryption algorithm is not supported.

Recommended Action Specify a valid encryption algorithm for the IPsec transform.

Error Message    %CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED_FULL_SPEED: Transform 
[chars] will run with reduced performance because of IPSec transform [chars]

Explanation The configured encryption algorithm will not run on the hardware encryption card. The transform is still usable but will run with reduced performance.

Recommended Action To reach the full performance of the encryption card, specify another encryption algorithm for the IPsec transform.

Error Message     %CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED_WITH_IKE: Transform [chars] 
not usable with IKE because of IPSec transform [chars]

Explanation The configured encryption algorithm is not usable with IKE with the current hardware configuration.

Recommended Action If IKE is required, specify a valid encryption algorithm for the IPsec transform.

Error Message    %CRYPTO-4-NOAUTOSAVE: Configuration was modified. Issue "write memory" 
to save new certificate

Explanation Auto Enrollment has obtained a new router key pair and certificate. However, the running configuration was previously modified.

Recommended Action Enter the write memory command to save the new certificates and keys.

Error Message    %CRYPTO-4-RECVD_PKT_INV_UDP_WRAPPER: Rec'd packet has invalid udp 
wrapper protocol. 	cryptoflags = [hex], sa->udp_wrapper_support = [dec],transform 
= [hex]

Explanation Either a UDP or encapsulated packet was received that is not a correct negotiation transform, or the system expected a UDP-encapsulated packet but received a non-UDP packet. There might be a policy setup error on the peer. This activity could be considered a hostile event.

Recommended Action Contact the administrator of the router or host that sent the packet to compare policy settings.

Error Message    %CRYPTO-4-TOKENKEYSDEACTIVATED: RSA keypairs from token [chars] and 
associated IPSEC sessions being deactivated now

Explanation Router RSA key pairs and associated IPsec sessions are being deactivated because the token containing them was removed.

Recommended Action Reinsert the crypto token.

Error Message     %CRYPTO-4-TOKENKEYTIMEOUT: RSA keypairs for token [chars] and 
associated IPSEC sessions will be deactivated in [dec] seconds

Explanation Router RSA key pairs and associated IPsec sessions will be deactivated when the timeout expires.

Recommended Action Reinsert the crypto token before the timeout expires.

CRYPTO-5

Error Message    %CRYPTO-5-GM_REGSTER: Start registration for group [chars] using 
address [chars]

Explanation Registration for one group has started.

Recommended Action No action is required.

Error Message    %CRYPTO-5-IKE_SA_HA_STATUS: IKE sa's if any, for vip [IP_address] will 
change from [chars] to [chars]

Explanation This is a notification message for crypto IKE SAs changing HA status.

Recommended Action No action is required.

Error Message    %CRYPTO-5-IKMP_AG_MODE_DISABLED: Unable to initiate or respond to 
Aggressive Mode while disabled

Explanation The router is configured to not accept or respond to ISAKMP aggressive mode with any peer.

Recommended Action If you did not intend to disable aggressive mode, remove the command.

Error Message    %CRYPTO-5-IPSEC_SA_HA_STATUS: IPSec sa's if any, for vip [IP_address] 
will change from [chars] to [chars]

Explanation This is a notification message for crypto IPsec SAs changing HA status.

Recommended Action No action is required.

Error Message    %CRYPTO-5-SESSION_STATUS: Crypto tunnel is [chars]. Peer 
[IP_address]:[dec] [chars] [chars] [chars] [chars] [chars] [chars] [chars] [chars]

Explanation This is a notification message for IPsec tunnel status.

Recommended Action This is an informational message only. No action is required.

CRYPTO-6

Error Message    %CRYPTO-6-AUTOGEN: Generated new [dec] bit key pair

Explanation Auto Enrollment has generated a new router key pair.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-AUTOSAVE: Running configuration saved to NVRAM

Explanation Auto Enrollment has obtained a new router key pair and certificate, and has done an automatic write to memory to save them.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-CERTIFSRECV: Could not receive router's Certificate from 
file system.

Explanation The router's certificate could not be received from the file system.

Recommended Action Verify the enrollment URL and verify that the router is able to read from the file system.

Error Message    %CRYPTO-6-CERTIFSSEND: Could not send Certificate enrollment request 
to file system.

Explanation The certificate enrollment request could not be sent to the file system.

Recommended Action Verify the enrollment URL and verify that the router is able to write to the file system.

Error Message    %CRYPTO-6-EZVPN_CONNECTION_DOWN: [chars]

Explanation The EZVPN connection is being closed. The IPsec and IKE security associations will also be brought down along with it.

Recommended Action No action is required.

Error Message     %CRYPTO-6-EZVPN_CONNECTION_UP: [chars]

Explanation The EZVPN connection is up for the specified client. Both IPsec and IKE security associations are up now.

Recommended Action No action is required.

Error Message    %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is [chars]

Explanation The ISAKMP process has been switched on or off either by the CLI or because no crypto map or EZVPN configuration is applied to any interface.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-PKCS12EXPORT_FAIL: PKCS #12 Export Failed.

Explanation An attempt to generate and export a PKCS #12 has failed.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-PKCS12EXPORT_SUCCESS: PKCS #12 Successfully Exported.

Explanation A PKCS #12 has been generated and successfully exported.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-PKCS12IMPORT_FAIL: PKCS #12 Import Failed.

Explanation An attempt to import a PKCS #12 has failed.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-PKCS12IMPORT_SUCCESS: PKCS #12 Successfully Imported.

Explanation A PKCS #12 has been successfully imported.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-3-POLICY_CKSUM_ERROR: Crypto policy checksum failure.

	Crypto access list [chars], crypto map [chars], interface [chars]

Explanation A crypto policy checksum failure has been detected in this router, whose traffic is protected by the crypto policy. This event may be caused by memory corruption occurring in crypto policy data or the memory area has been illegally modified. It may also be caused by software defects. As a result of this event, the router has been forced to reload.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CRYPTO-6-PRNG_SEED_KEY_ERROR: Pseudo-random number generator seed and 
seed key was identical

Explanation The X9.17 random number specification requires checking for the same value appearing as the seed and the seed key. This message indicates that the identical seed and seed key condition was discovered.

Recommended Action The X9.17 random number will occasionally produce this condition, and this is not a problem. If this message occurs frequently, the system should be manually reloaded. If the message is persistent across reloads, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message     %CRYPTO-6-TOKENADMINCHANGEPIN: Cryptographic Token [chars] ADMIN PIN 
change Successful

Explanation The cryptographic token has accepted the new administrator PIN offered by the router.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-TOKENADMINLOGIN: Cryptographic Token [chars] ADMIN Login 
Successful

Explanation The cryptographic token has accepted the administrator PIN offered by the router.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-TOKENCHANGEPIN: Cryptographic Token [chars] PIN change 
Successful

Explanation The cryptographic token has accepted the new PIN offered by the router.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-TOKENINSERTED: Cryptographic token [chars] inserted in 
[chars]

Explanation A cryptographic token has been detected.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-TOKENLOGIN: Cryptographic Token [chars] Login Successful

Explanation The cryptographic token has accepted the PIN offered by the router.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-TOKENLOGOUT: Cryptographic Token [chars] Logout Successful

Explanation The router has logged out from the cryptographic token.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-TOKENREMOVED: Cryptographic token [chars] removed from 
[chars]

Explanation A cryptographic token has been detected.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-TOKENSTOREKEY: Key [chars] stored on Cryptographic Token 
[chars] Successfully

Explanation A new key pair has been written out to the cryptographic token.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-TOKENTIMEOUTCANCELLED: Cryptographic Token [chars] 
re-inserted. removal timeout cancelled

Explanation A cryptographic token containing private keyfiles has been reinserted before the timeout. Router RSA key pairs and associated IPsec sessions will not be deactivated.

Recommended Action This is an informational message only. No action is required.

Error Message    %CRYPTO-6-VPN_TUNNEL_STATUS: [chars]

Explanation VPN tunnel status.

Recommended Action This is an informational message only. No action is required.

CRYPTO_HA Messages

This section contains crypto high availability messages.

CRYPTO_HA-3

Error Message    %CRYPTO_HA-3-IKEADDENTRYFAIL: (VIP=[IP_address])ISAKMP SA entry 
insertion on standby device failed for src=[IP_address], dst=[IP_address]

Explanation An attempt to insert an SA entry transferred from the active device has failed. The SA database is no longer synchronized with that on the active device.

Recommended Action Initiate a manual resynchronization of the ISAKMP SA table.

Error Message    %CRYPTO_HA-3-IKEDELENTRYFAIL: (VIP=[IP_address])ISAKMP SA entry 
deletion on standby device failed for src=[IP_address], dst=[IP_address]

Explanation An attempt to delete an SA entry that was removed on the active device has failed. The SA database is no longer synchronized with that on the active device.

Recommended Action Initiate a manual resynchronization of the ISAKMP SA table.

Error Message    %CRYPTO_HA-3-IKEINSERTKEYFAIL: (VIP=[IP_address])ISAKMP SA entry key 
insertion on standby device failed for src=[IP_address], dst=[IP_address]

Explanation An attempt to insert keys for a new SA entry on the standby device has failed. The standby device will not receive this entry.

Recommended Action Initiate a manual resynchronization of the ISAKMP SA table from the standby device.

Error Message    %CRYPTO_HA-3-IKEQUERYKEYFAIL: (VIP=[IP_address])ISAKMP SA entry key 
query on active device failed for src=[IP_address], dst=[IP_address]

Explanation An attempt to query an SA entry for key information to send to the standby device has failed. The standby device will not receive this entry.

Recommended Action Initiate a manual resynchronization of the ISAKMP SA table from the standby device.

Error Message    %CRYPTO_HA-3-IPSECADDENTRYFAIL: (VIP=[IP_address])IPSEC SA entry 
insertion on standby device failed

Explanation An attempt to insert an SA entry transferred from the active device has failed. The SA database is no longer synchronized with the database on the active device.

Recommended Action Initiate a manual resynchronization of the IPsec SA table.

Error Message    %CRYPTO_HA-3-IPSECDELENTRYFAIL: (VIP=[IP_address])IPSEC SA entry 
deletion on standby device failed

Explanation An attempt to delete an SA entry that was removed on the active device has failed. The SA database is no longer synchronized with the database on the active device.

Recommended Action Initiate a manual resynchronization of the IPsec SA table.

CRYPTO_HA-6

Error Message    %CRYPTO_HA-6-IKEDOWN: (VIP=[IP_address])Disabling High Availability 
functionality for the ISAKMP failover group.

Explanation This is a normal notification message when HA is unconfigured for this failover group, or a tracked interface is shut down. However, it may also be a result of a failure.

Recommended Action If the failover was initiated deliberately (for example, by shutting down a tracked interface), then no action is required. Otherwise, investigate the status of the redundancy protocol (HSRP, for example) that may have lead to the Down state notification to the high availability framework.

Error Message    %CRYPTO_HA-6-IKEFAILOVER: (VIP=[IP_address])Taking over as the new 
Active device for the ISAKMP failover group.

Explanation This is a normal notification message when an active device is first elected. Alternatively, it is triggered when a failover occurs within the high availability group. In that case, the formerly active device within the ISAKMP failover group has gone down and this device is taking over as the new active device for the group.

Recommended Action If the failover was initiated deliberately (for example, by shutting down a tracked interface), then no action is required. Otherwise, investigate the status of the previous active device to troubleshoot the reason for failure and take appropriate action.

Error Message    %CRYPTO_HA-6-IKEHAINFINITEMSGLOOP: (VIP=[IP_address])Dropping 
remainder of this HA IKE SSP message because of suspected infinite message loop.

Explanation HA IKE SSP message processing seems to be looping on this message. The processing of this message will be dropped to prevent an infinite loop.

Recommended Action Turning on detailed IKE HA debugs on both HA pairs can help determine what message may be causing this problem.

Error Message    %CRYPTO_HA-6-IKEHANOTENABLE: IKE HA is not enabled.

Explanation IKE HA received a state notification or an SSP message for a VIP that does not have HA enabled.

Recommended Action Verify that IKE stateful failover is configured for the interface with this VIP.

Error Message    %CRYPTO_HA-6-IKEHASYNCCOMPLETE: (VIP=[IP_address])IKE HA state 
synchronization with Active device complete.

Explanation This is a normal notification message after the standby has received either REPLY_ENTRY or DELETE_ENTRY messages for all requests during synchroniztion.

Recommended Action No action is required.

Error Message    %CRYPTO_HA-6-IKESTANDBY: (VIP=[IP_address])Setting up as a Standby 
device for the ISAKMP failover group.

Explanation This is a normal notification message after a standby device comes up.

Recommended Action No action is required.

Error Message    %CRYPTO_HA-6-IKEUPDATEENTRYFAIL: (VIP=[IP_address])ISAKMP SA entry 
update on standby device failed for src=[IP_address], dst=[IP_address]

Explanation An attempt to update an SA entry as specified by the active device has failed. The SA entry will be missing the latest packet level update until another update entry is sent by the active device.

Recommended Action Normally, a subsequent update entry message will self-correct the problem. Manual resynchronization of the ISAKMP SA table by the standby device may be necessary if this message appears repeatedly.

Error Message    %CRYPTO_HA-6-IPSECDOWN: (VIP=[IP_address])Disabling High Availability 
functionality for the IPSEC failover group.

Explanation This is a normal notification message when HA is unconfigured for this failover group, or a tracked interface is shut down. However, it may also be a result of a failure.

Error Message    %CRYPTO_HA-6-IPSECFAILOVER: (VIP=[IP_address])Taking over as the new 
Active device for the IPSEC failover group.

Explanation This is a normal message when a device first becomes active, or when failover occurs within the high availability group. In the failover case, the former active device within the IPsec failover group has gone down and this device is taking over as the new active device for the group.

Recommended Action If the failover was initiated deliberately (for example, by shutting down a tracked interface), then no action is required. Otherwise, investigate the status of the previous active device to troubleshoot the reason for failure and take appropriate action.

Error Message    %CRYPTO_HA-6-IPSECHAMAXINSERTERRORS: IPsec HA has failed inserting SAs 
for the last [int] seconds, the box is either out of resources or has suffered a 
hardware failure

Explanation The device is normally out of resources for short periods of time, and retries will automatically occur. In this case, however, the retries have not succeeded and have stopped. Action is required from the administrator.

Recommended Action Verify that both devices in the HA pair are identical and that the hardware is working properly.

Error Message    %CRYPTO_HA-6-IPSECHANOTENABLE: (VIP=[IP_address])IPSEC HA is not 
enabled.

Explanation IPsec HA received a state notification or an SSP message for a VIP that does not have HA enabled.

Recommended Action Verify that IPsec stateful failover is configured for the interface with this VIP.

Error Message    %CRYPTO_HA-6-IPSECHASYNCCOMPLETE: (VIP=[IP_address])IPSEC HA state 
synchronization with Active device complete.

Explanation This is a normal notification message after the standby has received either a REPLY_ENTRY or a DELETE_ENTRY message for all requests during synchroniztion.

Recommended Action No action is required.

Error Message    %CRYPTO_HA-6-IPSECSTANDBY: (VIP=[IP_address])Setting up as a Standby 
device for the IPSEC failover group.

Explanation This is a normal notification message when a standby device comes up.

Recommended Action No action is required.

Error Message    %CRYPTO_HA-6-IPSECUPDATEENTRYFAIL: (VIP=[IP_address])IPSEC SA entry 
update on standby device failed

Explanation An attempt to update an IPsec SA entry as specified by the active device failed. The SA entry will be missing the latest packet level update, until another update entry is sent by the active device.

Recommended Action Normally, a subsequent update entry message will self-correct the problem. Manual resynchronization of the IPsec SA table by the standby device may be necessary, if this message appears repeatedly.

CRYPTO_HA_IKE Messages

This section contains encryption (CRYPTO) high availability (HA) IKE messages.

CRYPTO_HA_IKE-3

Error Message    %CRYPTO_HA_IKE-3-FAILOVER_ERROR: Attempt to failover IKE SA 
([IP_address]:[IP_address]) failed due to [chars]. No stateful failover available 
for this SA.

Explanation The HA active device attempted to checkpoint the state of an IKE SA to the standby device, but the standby device was unable to create the standby IKE SA.

Recommended Action Search for other error messages at WARNING log level or turn on debugging messages to find the specific cause of the failure.

CRYPTO_HA_IKE-4

Error Message    %CRYPTO_HA_IKE-4-CRYPTO_HA_NOT_SUPPORTED_BY_HW: Crypto hardware is 
enabled and it does not support HA operation '[chars]'

Explanation Crypto hardware is enabled, but the hardware does not support HA operations such as insertion and extraction of keys.

Recommended Action Replace the crypto module with one that supports HA operations, or disable the hardware and use the software crypto engine.

CRYPTO_HA_IPSEC Messages

This section contains encryption (CRYPTO) high availability (HA) IPsec messages.

CRYPTO_HA_IPSEC-3

Error Message    CRYPTO_HA_IPSEC-3-FAILOVER_ERROR: Attempt to failover IPSec SA 
([IP_address]:[IP_address]) failed due to [chars]. No stateful failover available 
for this SA.

Explanation The HA active device attempted to checkpoint the state of an IKE SA to the standby device, but the standby device was unable to create the standby IKE SA.

Recommended Action Search for other error messages at log level WARNING or turn on debugging messages to find the specific cause of the failure.

Error Message     CRYPTO_HA_IPSEC-3-HA_IPSEC_UPDATE_PROC_FAIL: Start of HA IPSec update 
process failed

Explanation The IPsec HA process failed to start. Updates will not be sent from the active device to the standby device.

Recommended Action The module may need to be rebooted if this is a part of an IPsec HA setup.

CRYPTO_HA_IPSEC-4

Error Message    CRYPTO_HA_IPSEC-4-CRYPTO_HA_NOT_SUPPORTED_BY_HW: Crypto hardware is 
enabled and it does not support HA operation '[chars]'

Explanation Crypto Hardware is enabled, but the hardware does not support HA operations such as insertion and extraction of keys.

Recommended Action Replace the crypto module with one that supports HA operations, or disable the hardware and use the software crypto engine.

CRYPTO_RSA_ISSU Messages

This section contains encryption (CRYPTO) RSA in-service software upgrade (ISSU) messages.

CRYPTO_RSA_ISSU-3

Error Message    %CRYPTO_RSA_ISSU-3-GET_BUFFER: Crypto RSA ISSU client failed to get 
buffer for message. Error: %d (%s)

Explanation The crypto RSA ISSU client was unable to obtain a buffer for building a negotiation message. As a result, the client cannot send the negotiation message to the standby unit and the standby unit cannot be brought up.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, and show checkpoint client commands and your pertinent troubleshooting logs.

Error Message    %CRYPTO_RSA_ISSU-3-INIT: Crypto RSA ISSU client initialization failed 
to %s. Error: %d (%s)

Explanation The crypto RSA ISSU client could not be initialized. This condition will cause a catastrophic failure when an ISSU upgrade or downgrade is performed.

Error Message    %CRYPTO_RSA_ISSU-3-INVALID_SESSION: Crypto RSA ISSU client does not 
have a valid registered session.

Explanation The crypto RSA ISSU client does not have a valid registered session. This condition will prevent the standby unit from coming up.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, show issu capability entries, show issu session, and show issu negotiated capability commands and your pertinent troubleshooting logs.

Error Message    %CRYPTO_RSA_ISSU-3-MSG_NOT_OK: Crypto RSA ISSU client message type %d 
is not compatible

Explanation The crypto RSA ISSU client received an incompatible message from the peer unit. Because the message is not compatible, it cannot be processed by this unit.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, show issu message group, show issu session, and show issu negotiated version commands and your pertinent troubleshooting logs.

Error Message    %CRYPTO_RSA_ISSU-3-MSG_SIZE: Crypto RSA ISSU client failed to get the 
MTU for message type %d. Error: %d (%s)

Explanation The crypto RSA ISSU client was unable to calculate the MTU for the message specified. The 802.1X ISSU client will be unable to send the message to the standby unit.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, show issu message group, show issu session, and show issu negotiated version commands and your pertinent troubleshooting logs.

Error Message    %CRYPTO_RSA_ISSU-3-SEND_NEGO_FAILED: Crypto RSA ISSU client failed to 
send negotiation message. Error: %d (%s)

Explanation The crypto RSA ISSU client failed to send a session negotiation message to the peer. This condition will prevent the standby unit from coming up.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, and show checkpoint client commands and your pertinent troubleshooting logs.

Error Message    %CRYPTO_RSA_ISSU-3-SESSION_NEGO: Crypto RSA ISSU client encountered 
unexpected client nego_done. Error: %d (%s)

Explanation The crypto RSA ISSU client encountered an unexpected 'client negotiation done'. If a problem occurs with the ISSU session negotiation, the standby device cannot be brought up properly.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, show issu session, and show issu negotiated capability commands and your pertinent troubleshooting logs.

Error Message    %CRYPTO_RSA_ISSU-3-SESSION_REGISTRY: Crypto RSA ISSU client failed to 
register session information. Error: %d (%s)

Explanation The crypto RSA ISSU client failed to register session information. This condition will prevent the standby unit from coming up.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, show issu capability entries, show issu session, and show issu negotiated capability commands and your pertinent troubleshooting logs.

Error Message    %CRYPTO_RSA_ISSU-3-SESSION_UNREGISTRY: Crypto RSA ISSU client failed 
to unregister session information. Error: %d (%s)

Explanation The crypto RSA ISSU client failed to unregister session information.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, show issu session, and show issu negotiated capability commands and your pertinent troubleshooting logs.

Error Message    %CRYPTO_RSA_ISSU-3-TRANSFORM_FAIL: Crypto RSA ISSU client %s transform 
failed for message type %d. Error: %d (%s)

Explanation The crypto RSA ISSU client could not transform the message. If the transmit transformation failed, the checkpoint message cannot be sent to the standby unit. If the receive transformation failed, the checkpoint message cannot be applied on the standby unit. In either case, the crypto RSA state will not match with the active unit.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, show issu session, and show issu negotiated version commands and your pertinent troubleshooting logs.

CSG Messages

This section contains Content Services Gateway (CSG) messages.

CSG-3

Error Message    %CSG-3-ERROR: Module [dec]: [chars]

Explanation An error occurred in a CSG module.

Error Message    %CSG-3-RELOADNOTOK: CSG ACCOUNTING [chars] reload on module [dec] 
failed.

Explanation This informational message appears whenever a CSG configuration is reloaded as a result of power cycling a CSG card.

Recommended Action This is an informational message only. No action is required.

CSG-4

Error Message    %CSG-4-WARNING: Module [dec]: [chars]

Explanation An undesired event has occurred in a CSG module.

CSG-6

Error Message    %CSG-6-LIRELOADOK: CSG LI reload on module [dec] successful

Explanation The CSG lawful intercept (LI) configuration was reloaded because of the power cycling of a CSG module.

Recommended Action No action is required.

Error Message    %CSG-6-RELOADOK: CSG ACCOUNTING [chars] reload on module [dec] 
successful

Explanation This informational message appears whenever a CSG configuration is reloaded as a result of power cycling a CSG card.

Recommended Action This is an informational message only. No action is required.

CSM_SLB Messages

This section contains Content Switching Module (CSM) server load balancing (SLB) messages.

CSM_SLB-4

Error Message    %CSM_SLB-4-ENV_VARIABLE: Module %d warning: %s %s

Explanation There is a mismatch between the configuration and the specified environment variable.

Recommended Action Check the documentation for any caveats regarding the use of the specified environment variable.

CT3 Messages

This section contains CT3 shared port adapter messages.

Error Message    %CT3-3-CT3NOACC: [chars] - Accumulator is not available

Explanation An invalid TX accumulator is detected.

Error Message    %CT3-3-MBOXRECV: Failed to receive reply [dec] from bay [dec] firmware

Explanation A message was not received from CT3 firmware.

Recommended Action Copy the error message exactly as it appears, collect the output of the show tech-support command immediately, and report it to your technical support representative. If possible, try to do an OIR (Online Insertion and Removal). Please refer to the Cisco documentation for information on 'Online Insertion and Removal' for your platform

Error Message    %CARRIER-2-TOOMANY_CT3: Too many CT3 DFC cards, do not power up invalid 
card in slot [dec]

Explanation The user has put too many CT3 DFC cards in the chassis.

Recommended Action Remove the extra CT3 DFC card, or 8PRI DFC card causing the problem.

CTS Messages

This section contains Cisco TrustSec (CTS) messages.

CTS-0

Error Message    %CTS-0-AUTHZ_OUT_OF_MEM: %s failed to create %s due to insufficient 
memory

Explanation A Cisco TrustSec (CTS) process failed due to insufficient system memory.

Error Message    %CTS-0-CTS_EMERG: [chars]

Explanation An internal software error occurred.

Error Message    %CTS-0-IFC_OUT_OF_MEM: %s failed to create %s due to insufficient 
memory

Explanation A Cisco TrustSec (CTS) process failed due to insufficient system memory.

CTS-1

Error Message    %CTS-1-CTS_ALERT: [chars]

Explanation An internal software error occurred.

CTS-2

Error Message    %CTS-2-CTS_CRIT: [chars]

Explanation An internal software error occurred.

Recommended Action Copy the error message exactly as it appears on the console or in the system log. Research and attempt to resolve the error using the Output Interpreter https://www.cisco.com/cgi-bin/Support/OutputInterpreter/home.pl. Issue the show tech-support command to gather data that may help identify the nature of the error. Also perform a search of the Bug Toolkit http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support.

CTS-3

Error Message    %CTS-3-AUTHZ_ADD_DATA_FAILED: %s failed to add %s to %s

Explanation An error occurred while the Cisco TrustSec (CTS) authorization attempted to build its database.

Error Message    %CTS-3-AUTHZ_DATA_CREATE_FAILED: %s failed to create %s

Explanation Cisco TrustSec (CTS) authorization was unable to create an internal data structure.

Error Message    %CTS-3-AUTHZ_DATA_EXCEEDS_LIMIT: %s encountered %s(%d) exceeds max(%d)

Explanation Cisco TrustSec (CTS) authorization data exceeded the maximum allowed limit.

Error Message    %CTS-3-AUTHZ_DATA_FAILED: %s failed to obtain %s

Explanation Cisco TrustSec (CTS) authorization was unable to get or create a data structure.

Error Message    %CTS-3-AUTHZ_DATA_NULL: %s encounters NULL %s

Explanation Cisco TrustSec (CTS) authorization encountered an unexpected NULL pointer or data.

Error Message    %CTS-3-AUTHZ_DATA_UNINIT: %s appears uninitialized

Explanation Cisco TrustSec (CTS) authorization unexpectedly encountered uninitialized data.

Error Message    %CTS-3-AUTHZ_FAILED_SYNC_RCV: Standby failed receive sync msg(%s)

Explanation An error occurred while the standby unit was receiving synchronization data from the active unit.

Error Message    %CTS-3-AUTHZ_GENERIC_FAILURE: %s %s

Explanation Cisco TrustSec (CTS) authorization encountered an internal error.

Error Message    %CTS-3-AUTHZ_INSTALL_FAILED: %s failed to install %s %s

Explanation An error occurred while Cisco TrustSec (CTS) authorization attempted to build its database.

Error Message    %CTS-3-AUTHZ_INVALID_DATA: %s encountered invalid %s

Explanation Cisco TrustSec (CTS) authorization encountered an invalid data type.

Error Message    %CTS-3-AUTHZ_NOT_SUPPORTED: %s encountered %s not unsupported

Explanation Cisco TrustSec (CTS) authorization encountered an unsupported data type or feature, possibly due to incompatibility.

Error Message    %CTS-3-AUTHZ_POLICY_FALLBACK_FAILED: Failed to %s Fallback policy for 
%s

Explanation Cisco TrustSec (CTS) was unable to install a fallback authorization policy.

Error Message    %CTS-3-AUTHZ_POLICY_INGRESS_FAILED: Failed to %s Ingress policy for %s

Explanation Cisco TrustSec (CTS) was unable to acquire or install an ingress policy from the access control server.

Error Message    %CTS-3-AUTHZ_POLICY_INTERNAL_FAILED: Failed to acquire/install policy 
for %s due to internal error

Explanation Cisco TrustSec (CTS) was unable to acquire or install a policy due to an internal software error.

Error Message    %CTS-3-AUTHZ_POLICY_PEER_DOWNLOAD_FAILED: Failed to download peer 
policy for %s

Explanation Cisco TrustSec (CTS) was unable to acquire a peer policy from the access control server.

Error Message    %CTS-3-AUTHZ_POLICY_RBACL_FAILED: Failed to %s RBACL %s for SGT=%d

Explanation Cisco TrustSec (CTS) was unable to acquire a role-based access control list (RBACL) policy from the access control server.

Error Message    %CTS-3-AUTHZ_POLICY_WILDCARD_FAILED: Failed to download wildcard 
policy

Explanation Cisco TrustSec (CTS) was unable to acquire a wildcard policy from the access control server.

Error Message    %CTS-3-AUTHZ_SYNC_FAILED: Failed to send %s sync msg(%s) to Standby

Explanation An error occurred while Cisco TrustSec (CTS) authorization was performing a synchronization of the standby unit.

Error Message    %CTS-3-CTS_ERR: [chars]

Explanation An internal software error occurred.

Error Message    %CTS-3-DOT1X_CONFIG_FAILED: Failed to configure dot1x for int(%s)

Explanation Cisco TrustSec (CTS) was unable to configure 802.1X for a CTS link.

Error Message    %CTS-3-DOT1X_FORCE_PORT_AUTHORIZED_FAILED: Failed to force dot1x port 
authorized for int(%s)

Explanation Cisco TrustSec (CTS) authorization was unable to FORCE AUTHORIZED an 802.1X port on a CTS link.

Error Message    %CTS-3-DOT1X_INIT_FAILED: Failed to initialize dot1x for int(%s)

Explanation Cisco TrustSec (CTS) was unable to initialize 802.1X for a CTS link.

Error Message    %CTS-3-DOT1X_PAE_FAILED: Failed to %s dot1x PAE(%s) for int(%s)

Explanation Cisco TrustSec (CTS) was unable to start or stop an 802.1X Port Access Entity (PAE) for a CTS link.

Error Message    %CTS-3-GENERIC_FAILURE: %s %s

Explanation Cisco TrustSec (CTS) encountered an internal error.

Error Message    %CTS-3-GLOBAL_DOT1X_DISABLED: Global dot1x config is currently 
disabled - CTS will not run

Explanation Because global 802.1X is not enabled, Cisco TrustSec (CTS) will not run.

Error Message    %CTS-3-IFC_DATA_DESC_DECODE_FAILED: %s failed to decode the 
data-descriptori - swidb unknown

Explanation Cisco TrustSec (CTS) was unable to decode the data descriptor in order to obtain the software interface descriptor block (SWIDB).

Error Message    %CTS-3-IFC_DATA_DESC_ENCODE_FAILED: %s failed to encode the 
data-descriptor for int(%s)

Explanation Cisco TrustSec (CTS) was unable to encode the software interface descriptor block (SWIDB) into the data descriptor.

Error Message    %CTS-3-IFC_DATA_NULL: %s encounters NULL %s

Explanation Cisco TrustSec (CTS) encountered an unexpected NULL pointer or data.

Error Message    %CTS-3-IFC_LINK_OBJ_FAILED: %s failed to get link_obj for int(%s)

Explanation Cisco TrustSec (CTS) IFC was unable to access the link object.

Error Message    %CTS-3-IFC_SYNC_FAILED: Failed to send %s sync msg(%s) to Standby

Explanation An error occurred while Cisco TrustSec (CTS) IFC was performing a synchronization of the standby unit.

Error Message    %CTS-3-IFC_SYNC_FAILED_2: %s, Failed to send %s sync msg(%s) to Standby

Explanation An error occurred while Cisco TrustSec (CTS) IFC was performing a synchronization of the standby unit.

Error Message    %CTS-3-INVALID_MSGID_RCV: %s received invalid HA/ISSU msgId(%d)

Explanation Cisco TrustSec (CTS) encountered an unexpected invalid HA/ISSU message ID.

Error Message    %CTS-3-PORT_AUTHORIZED_FAILED: Failed to authorize Port for int(%s)

Explanation A port could not be authorized on a Cisco TrustSec (CTS) link.

Error Message    %CTS-3-PP_CTS_EC_NOT_CTS: Physical port is not configured for CTS, but 
port-channel is.

Explanation A physical port cannot join the channel group (port channel) because its Cisco TrustSec (CTS) configuration does not match the channel group's CTS configuration.

Error Message    %CTS-3-PP_CTS_MODE_EC_MISMATCH: Physical port CTS mode does not match 
the port-channel's CTS mode.

Explanation A physical port cannot join the port channel because its Cisco TrustSec (CTS) mode does not match the port channel's CTS mode.

Error Message    %CTS-3-PP_CTS_TIMER_REAUTH_EC_MISMATCH: Cannot bundle interface. CTS 
Reauth Timer mismatch. %s = %d %s = %d

Explanation A physical port cannot join the port channel because its Cisco TrustSec (CTS) reauthentication timer value does not match the port channel's timer value.

Error Message    %CTS-3-PP_NOT_CTS_EC_CTS: Physical port is configured for CTS, but 
port-channel is not.

Explanation A physical port cannot join the channel group (port channel) because its Cisco TrustSec (CTS) configuration does not match the channel group's CTS configuration.

Error Message    %CTS-3-SEND_MSG_TO_CORE_FAILED: Failed to send msg([dec]) to core 
process

Explanation An error occcured while CTS attempts to to send a message event to the core process

Error Message    %CTS-3-SXP_BINDING_ERR: Binding [chars]- [chars]

Explanation SXP binding update error.

Error Message    %CTS-3-SXP_CONN_STATE_CHG_OFF: Connection [chars]-[dec] state changed 
from [chars] to Off.

Explanation SXP Connection with the specified instance number changed state.

Recommended Action No action is required.

Error Message    %CTS-3-SXP_LISTENER: Fail to start global listening socket after TCP 
process restart.

Explanation The Security Exchange Protocol (SXP) process could not start after a restart.

Error Message    %CTS-3-SXP_MSG_PARSE: Connection [chars] [chars]

Explanation An error occurred while parsing SXP message.

CTS-4

Error Message    %CTS-4-CTS_WARNING: [chars]

Explanation An internal software error occurred.

Error Message    %CTS-4-SXP_INTERNAL: CTS SXP [chars]

Explanation The CTS SXP system encountered internal failure.

CTS-5

Error Message    %CTS-5-CTS_NOTICE: [chars]

Explanation Normal but significant conditions

Error Message    %CTS-5-SXP_BINDING_ADD: Binding [chars]- added to SXP database.

Explanation Binding added to the SXP database.

Recommended Action No action is required.

Error Message    %CTS-5-SXP_BINDING_CHG: Binding [chars]- changed: old connection 
instance number:[dec], old sgt:[dec].

Explanation Binding changed in the SXP database.

Recommended Action No action is required.

Error Message    %CTS-5-SXP_BINDING_DEL: Binding [chars]- deleted in SXP database.

Explanation Binding deleted in the SXP database.

Recommended Action No action is required.

Error Message    %CTS-5-SXP_BINDING_FWD: Binding [chars]- is forwarded to the peer.

Explanation SXP forwarded binding to the peer.

Recommended Action No action is required.

Error Message    %CTS-5-SXP_BINDING_REQ: SXP received binding forwarding request 
([chars]) binding [chars].

Explanation SXP received a binding forwarding request.

Recommended Action No action is required.

Error Message    %CTS-5-SXP_BINDING_UPD: Binding [chars] [chars]. Update binding 
manager.

Explanation SXP updated binding manager with the binding change.

Recommended Action No action is required.

Error Message    %CTS-5-SXP_DFT_PASSWORD_CHANGE: CTS SXP password changed.

Explanation The SXP system password has been changed.

Recommended Action No action is required.

Error Message    %CTS-5-SXP_DFT_SRCIP_CHG: SXP default source IP is changed 
[IP_address] -- [IP_address].

Explanation SXP default source IP is changed on this device.

Recommended Action No action is required.

Error Message    %CTS-5-SXP_VRF_DEL: SXP Connection  configuration in VRF:[chars] is 
removed.

Explanation A VRF is removed, the connections configured in this VRF should be removed.

Recommended Action No action is required.

Error Message    %CTS_HA_ISSU-3-CAP_INVALID_SIZE: CTS HA empty tlv size.

Explanation Received empty tlv list during capability negotiation.

CTS-6

Error Message    %CTS-6-DOT1X_FORCE_PORT_AUTHORIZED_SUCCESS: Successfully forced dot1x 
port authorized for int(%s)

Explanation Cisco TrustSec (CTS) authorization caused FORCE AUTHORIZED on an 802.1X port on a CTS link.

Recommended Action No action is required.

Error Message    %CTS-6-DOT1X_PAE_CONFIG: %s dot1x PAE(%s) for int(%s)

Explanation The specified interface has been configured to be an 802.1X Port Access Entity (PAE).

Recommended Action No action is required.

Error Message    %CTS-6-IFC_CACHE_APPLIED: Cache data applied for int(%s)

Explanation The Cisco TrustSec (CTS) link was brought up using cache data.

Recommended Action No action is required.

Error Message    %CTS-6-CTS_INFO: [chars]

Explanation Informational messages

Recommended Action No action is required.

Error Message    %CTS-6-PORT_AUTHORIZED_SUCCESS: Port authorized for int(%s)

Explanation A port was authorized on a Cisco TrustSec (CTS) link.

Recommended Action No action is required.

Error Message    %CTS-6-PORT_UNAUTHORIZED: Port unauthorized for int(%s)

Explanation A port has become unauthorized on a Cisco TrustSec (CTS) link.

Recommended Action No action is required.

Error Message    %CTS-6-SXP_CONFIG: Connection [chars] [chars]

Explanation A SXP configuration error occurred. The connection can not be setup correctly.

Recommended Action Ensure that the connection configure on both ends have the matched mode, IP addresses.

Error Message    %CTS-6-SXP_CONN_STATE_CHG: Connection [chars]-[dec] state changed from 
[chars] to [chars].

Explanation SXP Connection with the specified instance number changed state.

Recommended Action No action is required.

Error Message    %CTS-6-SXP_SRC_IP: Source IP address ([chars] [IP_address]) does not 
belong to this device.

Explanation An error occurred while using this source IP address to set up SXP connection.

Recommended Action Re-configure SXP connection to have a valid source IP address.

Error Message    %CTS-6-SXP_TIMER_START: Connection [chars] [chars] timer started.

Explanation The specified SXP timer started.

Recommended Action No action is required.

Error Message    %CTS-6-SXP_TIMER_STOP: Connection [chars] [chars] timer stopped.

Explanation The specified SXP timer stopped.

Recommended Action No action is required.

CTS-7

Error Message    %CTS-7-CTS_ASSERT: Assertion Failure ( [chars] @[chars]:[dec] ) : 
[chars]

Explanation An internal software error occurred.

Recommended Action Copy the error message exactly as it appears on the console or in the system log. Research and attempt to resolve the error using the Output Interpreter https://www.cisco.com/cgi-bin/Support/OutputInterpreter/home.pl. Issue the show tech-support command to gather data that may help identify the nature of the error. Also perform a search of the Bug Toolkit http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support.

CTS_HA Messages

This section contains Cisco TrustSec (CTS) high availability (HA) messages.

CTS_HA-3

Error Message    %CTS_HA-3-CHKPT_REG_FAIL: CTS HA add CTS checkpoint client failure

Explanation The Cisco TrustSec (CTS) high availability (HA) process failed to add a checkpoint client. No CTS data will be synchronized with the standby device.

Error Message    %CTS_HA-3-RECEIVE_FAILED: CTS HA client failed to process message 
recieved from Active device.

Explanation The Cisco TrustSec (CTS) high availability (HA) client on the standby device failed to process a checkpoint message from the active device. The CTS state between the active device and the standby device is not identical.

Error Message    %CTS_HA-3-SEND_FAILED: CTS HA client on Active device failed to send 
checkpoint message. CTS component Id %d, message Id %d

Explanation The Cisco TrustSec (CTS) high availability (HA) client on the active device failed to send a checkpoint message to the standby device. The CTS state between the active device and the standby device is not identical.

CTS_HA_ISSU Messages

This section contains Cisco TrustSec (CTS) high availability (HA) in-service software upgrade (ISSU) messages.

CTS_HA_ISSU-3

Error Message    %CTS_HA_ISSU-3-CAP_INVALID_SIZE: CTS HA empty tlv size.

Explanation Received empty tlv list during capability negotiation.

Error Message    %CTS_HA_ISSU-3-CAP_NOT_COMPATIBLE: CTS HA capability not compatible

Explanation CTS HA failed during capability negotiation.

Error Message    %CTS_HA_ISSU-3-GET_BUFFER: CTS HA ISSU client failed to get buffer for 
message. Error: %d (%s)

Explanation The Cisco TrustSec (CTS) high availability (HA) ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation, the standby device cannot be brought up properly.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, and show checkpoint client commands and your pertinent troubleshooting logs.

Error Message    %CTS_HA_ISSU-3-INIT: CTS HA ISSU client initialization failed to %s. 
Error: %d (%s)

Explanation The Cisco TrustSec (CTS) high availability (HA) ISSU client could not be initialized. This initialization failure must be addressed before an in-service software upgrade or downgrade can be performed successfully. Otherwise, a software upgrade or downgrade will result in downtime.

Error Message    %CTS_HA_ISSU-3-MSG_NOT_COMPATIBLE_WITH_PEER: Message [dec] in 
component [dec] is not compatible with the peer.

Explanation Message not compatible with the peer.

Error Message    %CTS_HA_ISSU-3-SEND_NEGO_FAILED: CTS HA ISSU client failed to send 
negotiation message. Error: %d (%s)

Explanation The Cisco TrustSec (CTS) high availability (HA) ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation, the standby device cannot be brought up properly.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, and show checkpoint client commands and your pertinent troubleshooting logs.

Error Message    %CTS_HA_ISSU-3-SESSION_REGISTRY: CTS HA ISSU client failed to register 
session information. Error: %d (%s)

Explanation The Cisco TrustSec (CTS) high availability (HA) ISSU client failed to register session information. If a problem occurs with the ISSU session registration, the standby device cannot be brought up properly.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, show issu capability entries, show issu session, and show issu negotiated capability commands and your pertinent troubleshooting logs.

Error Message    %CTS_HA_ISSU-3-SESSION_UNREGISTRY: CTS HA ISSU client failed to 
unregister session information. Error: %d (%s)

Explanation The Cisco TrustSec (CTS) high availability (HA) ISSU client failed to unregister session information.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, show issu session, and show issu negotiated capability commands and your pertinent troubleshooting logs.

CTS_HA_ISSU-6

Error Message    %CTS_HA_ISSU-6-INCOMPAT: CTS HA ISSU client negotiation results 
incompatible

Explanation The Cisco TrustSec (CTS) high availability (HA) ISSU client message version is not compatible on the active and standby devices. As a result, no CTS data will be synchronized to the standby device.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, show logging, show issu capability entries, show issu session, and show issu negotiated version commands and your pertinent troubleshooting logs.

CWAN_ALARM Messages

This section contains Constellation WAN (CWAN) alarm messages.

CWAN_ALARM-6

Error Message    %CWAN_ALARM-6-INFO: [chars] [chars] [chars] [chars] [chars]

Explanation This message provides alarm assertion or deassertion information.

Recommended Action This is an informational message only. No action is required.

Error Message    %CWAN_ALARM-6-SONET: [chars] [chars] [chars] [chars] [chars]

Explanation This message is generated whenever an alarm is present in the system (and the alarm status has been reported to the RP) or an alarm has been removed from the system (and the alarm status has been reported to the RP .

Recommended Action This is an informational message only. No action is required.

Error Message    %CTS-6-SXP_PASSWORD_CHANGE: CTS SXP password changed

Explanation The Cisco TrustSec (CTS) Security Exchange Protocol (SXP) system password has been changed.

Recommended Action No action is required.

Error Message    %CTS-6-SXP_STATE_CHANGE: CTS SXP %s

Explanation The Cisco TrustSec (CTS) Security Exchange Protocol (SXP) system component has changed its operational state.

Recommended Action No action is required.

CWAN_ATM Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN ATM port (CWAN_ATM) messages.

CWAN_ATM-3

Error Message    %CWAN_ATM-3-LOWMEM: Could not allocate memory for RFC 1483 packet 
cloning.

Explanation Memory is running low.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message    %CWAN_ATM-3-PORT_ERR: Invalid PORT [dec]

Explanation The specified port does not exist.

Error Message    %CWAN_ATM-3-VCD_ERR: Invalid PortVCD [hex]

Explanation The specified port VCD does not exist.

Error Message    %CWAN_ATM-3-VC_ERR: Invalid VC [hex]

Explanation The specified VC does not exist on the port.

Error Message    %CWAN_ATM-3-VC_OR_PORT_ERR: Invalid VCD [hex] or Port: [dec]

Explanation Either the port or the VCD is invalid.

CWAN_ATM-5

Error Message    %CWAN_ATM-5-UNKNOWN_VCD: Unknown port vcd [hex] in egress packet

Explanation An unknown VCD has been received in the egress path of the module. This condition is most likely a transient condition, and it is usually caused by VCs that are being disassembled and reassembled while traffic is being passed.

Recommended Action No action is required.

CWAN_ATOM-HA Messages

This section contains Any Transport over MPLS (AToM) high availability messages.

CWAN_ATOM-HA-2

Error Message    %CWAN_ATOM_HA-2-ISSU_ERROR: [chars] [chars]

Explanation Platform ATOM HA ISSU client error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log. Research and attempt to resolve the error using the Output Interpreter https://www.cisco.com/cgi-bin/Support/OutputInterpreter/home.pl. Issue the show tech-support command to gather data that may help identify the nature of the error. Also perform a search of the Bug Toolkit http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support.

CWAN_ATOM-HA-3

Error Message    %CWAN_ATOM_HA-3-CF_ERROR: [chars] [dec]

Explanation Platform ATOM HA CF client error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log. Research and attempt to resolve the error using the Output Interpreter https://www.cisco.com/cgi-bin/Support/OutputInterpreter/home.pl. Issue the show tech-support command to gather data that may help identify the nature of the error. Also perform a search of the Bug Toolkit http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support.

Error Message    %CWAN_ATOM_HA-3-RF_ERROR: [chars] [dec]

Explanation Platform ATOM HA RF client error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log. Research and attempt to resolve the error using the Output Interpreter https://www.cisco.com/cgi-bin/Support/OutputInterpreter/home.pl. Issue the show tech-support command to gather data that may help identify the nature of the error. Also perform a search of the Bug Toolkit http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support.

CWAN_CHOC Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN Channelized OC48/OC12-related (CWAN_CHOC) messages.

CWAN_CHOC-4

Error Message    %CWAN_CHOC-4-CORRUPT: [chars] information seems to be corrupted, bad 
value =[int]

Explanation Incorrect parameters were detected internally.

Recommended Action This is only a debug warning message. The unexpected value is discarded.

CWAN_CHOC_DSX Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN CHOC DSX LC Common (CWAN_CHOC_DSX) messages.

CWAN_CHOC_DSX-3

Error Message    %CWAN_CHOC_DSX-3-NODESTROYSUBBLOCK: The [chars] subblock named [chars] 
was not removed

Explanation A software error occurred. This message displays when IDB subblocks cannot be removed.

CWAN_CT3 Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN module Channelized T3 (CWAN_CT3) messages.

CWAN_CT3-3

Error Message    %CWAN_CT3-4-CORRUPT: [chars] information seems to be corrupted, bad 
value =[int]

Explanation Incorrect parameters were detected internally.

Recommended Action This is only a debug warning message. The unexpected value is discarded.

CWAN_FWD_TABLES Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN module forwarding tables messages.

CWAN_FWD_TABLES-3

Error Message    %CWAN_FWD_TABLES-3-CHUNK_CREATE_FAIL: [chars]

Explanation An internal software error occurred.

Error Message    %CWAN_FWD_TABLES-3-CHUNK_DESTROY_FAIL: [chars]

Explanation An internal software error occurred.

Error Message    %CWAN_FWD_TABLES-3-CHUNK_MALLOC_FAIL: [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_FWD_TABLES-3-ENTRY_BUILD_FAIL: [chars] [int]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_FWD_TABLES-3-INVALID_DEST_INFO: [chars] [hex] [hex] [hex]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_FWD_TABLES-3-INVALID_INDEX: [chars] [int]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_FWD_TABLES-3-INVALID_OPR_TYPE: [chars] [dec]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_FWD_TABLES-3-MALLOC_FAILED: [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_FWD_TABLES-3-TABLE_ERROR: [chars]

Explanation An internal software error occurred.

CWAN_HA Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN module high availability (CWAN_HA) messages.

CWAN_HA-2

Error Message    %CWAN_HA-2-CCB_PLAYBACK_ERROR: CCB playback failed for slot [dec].

Explanation The high availability component for WAN modules failed to synchronize new state information for the specified slot.

Recommended Action Reload the redundant supervisor engine to force a fresh bulk synchronization. If this error recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs. Examine both the active supervisor engine and the redundant supervisor engine for messages.

Error Message    %CWAN_HA-2-CCB_RECORD_ERROR: CCB record failed for slot [dec].

Explanation The high availability component for WAN modules failed to record new state information for the specified slot. The system is falling back to RPR mode for high availability.

Recommended Action Examine both the active supervisor engine and the redundant supervisor engine for messages. Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_HA-2-IFCFG_PLAYBACK_ERROR: Interface Configuration command 
[int] playback failed for slot [int]/[int].

Explanation The high availability component for WAN modules failed to synchronize new state information for the specified slot. The redundant system is no longer synchronized with the active system. The redundant supervisor engine was reloaded shortly after this error was encountered.

Recommended Action If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_HA-2-IFCFG_RECORD_ERROR: Interface Configuration command [int] 
record failed for slot [int]/[int].

Explanation The high availability component for WAN modules failed to record some new state information for the specified slot. The system is falling back to RPR mode for high availability.

CWAN_HA-3

Error Message    %CWAN_HA-3-CCB_INIT_ERROR: Failed to initialize CCB list for slot 
[dec].

Explanation The high availability component for WAN modules failed to properly initialize state information for the specified slot. The system is falling back to RPR mode for high availability.

Error Message    %CWAN_HA-3-IFCFG_CMD_NOT_UNIQUE: More than one command registered for 
unique-key generator for interface configuration command [int].

Explanation The high availability component for WAN modules is unable to properly synchronize state information for the current configuration due to a conflict in command identifiers.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_HA-3-IFCFG_INIT_ERROR: Failed to initialize Interface 
Configuration list for slot [int]/[int].

Explanation The high availability component for WAN modules failed to properly initialize state information for the specified slot. The system is falling back to RPR mode for high availability.

Error Message    %CWAN_HA-3-IFCFG_NO_UNIQUE_KEY: No unique-key generator registered for 
interface configuration command [int].

Explanation The high availability component for WAN modules is unable to properly synchronize state information for the current configuration. The system is falling back to RPR mode for high availability.

CWAN_HA-4

Error Message    %CWAN_HA-4-CCB_PLAYBACK_ERROR: CCB playback failed for slot [dec].

Explanation The high availability component for WAN modules failed to synchronize some new state information for the specified slot.

Recommended Action Reload the standby supervisor engine to force a fresh bulk synchronization. If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_HA-4-CCB_RECORD_ERROR: CCB record failed for slot [dec].

Explanation The high availability component for WAN modules failed to record some new state information for the specified slot.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_HA-4-IFCFG_DFLT_LIST_ERROR: For Interface Configuration command 
%u, default retval list search resulted 0x%x for slot %u/%u

Explanation The high availability (HA) component for WAN modules failed to synchronize new state information for the specified slot.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging, show tech-support, and show platform redundancy if-config default-retvals commands and your pertinent troubleshooting logs.

Error Message    %CWAN_HA-4-IFCFG_PLAYBACK_ERROR: Interface Configuration command 
[int] playback failed for slot [int]/[int].

Explanation The high availability component for WAN modules failed to synchronize some new state information for the specified slot.

Recommended Action Copy the error message exactly as it appears on the console or in the system log. Research and attempt to resolve the error using the Output Interpreter https://www.cisco.com/cgi-bin/Support/OutputInterpreter/home.pl. Also perform a search of the Bug Toolkit http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.

Error Message    %CWAN_HA-4-IFCFG_RECORD_ERROR: Interface Configuration command [int] 
record failed for slot [int]/[int].

Explanation The high availability component for WAN modules failed to record some new state information for the specified slot.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_HA-4-LTLSYNCFAIL: Failed to sync LTL data during [chars] for 
[chars] [int]: (slot=[dec],slotunit=[dec],if_num=[dec]) to standby 
(vlan=[int],hash=[int],ltl=[int])

Explanation Some local target logic (LTL) data did not synchronize correctly from the active to the standby RP.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_HA-4-NOSRPBULKSYNC: Failed to [chars] srp bulk data (slot=[dec], 
intf=[dec], type=[dec]), ret code [dec]

Explanation The synchronization of RP bulk data and SRP bulk data failed from the active supervisor engine to the redundant supervisor engine.

Error Message    %CWAN_HA-4-NOSRPSYNC: Failed to sync srp packet 
(slot=[dec],intf=[dec]) to standby, HA_SYNC_STATUS=[dec]

Explanation The RP dynamic synchronization of SRP packets failed from the active supervisor engine to the redundant supervisor engine.

Error Message    %CWAN_HA-4-SRPSYNC: Slot [dec]: [chars]

Explanation The specified error occurred while synchronizing the SRP states from the active supervisor engine RP to the redundant supervisor engine RP.

CWAN_HAL Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN module Halcyon (CWAN_HAL) messages.

CWAN_HAL-3

Error Message    %CWAN_HAL-3-CHUNK_CREATE_FAIL: [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_HAL-3-CHUNK_MALLOC_FAIL: [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_HAL-3-DELETION_FAILED: [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_HAL-3-FILL_OCE_INFO_FAIL: [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_HAL-3-ILLEGAL_DEAGG_PROT_TYPE: [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_HAL-3-ILLEGAL_OBJ_TYPE: [chars] [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_HAL-3-INSERTION_OR_UPDATION_FAILED: [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_HAL-3-LABEL_SPACE_INCONSISTENT: [chars] [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_HAL-3-NULL_OBJ_HANDLE: [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_HAL-3-NULL_PLT_SPACE: [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_HAL-3-TABLE_CREATION_FAILED: [chars] [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

Error Message    %CWAN_HAL-3-TABLE_DELETION_FAILED: [chars] [chars]

Explanation There is a problem with internal software coding. This message should not appear under normal operation.

CWAN_HAL-4

Error Message    %CWAN_HAL-4-UN_SUPPORTED_CONFIG: %s

Explanation The configuration of the WAN module is not supported. A common cause is configuring TE on a GRE tunnel.

CWAN_IFMGR Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN module Interface Manager (CWAN_IFMGR) messages.

CWAN_IFMGR-4

Error Message    %CWAN_IFMGR-4-CREATEFAIL: IM Driver Creation Failed: Interface 
[dec]/[dec]: [chars]

Explanation Driver failed to create an interface with the interface manager.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     %CWAN_IFMGR-4-DESTROYFAIL: IM Driver Destroy Failed: Interface 
[dec]/[dec]: [chars]

Explanation Driver failed to destroy the interface with the interface manager.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     %CWAN_IFMGR-4-REGISTERFAIL: IM Registration Failed: [chars]

Explanation Driver failed to register with the interface manager.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

CWANLC Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN module (CWANLC) messages.

CWANLC-3

Error Message    %CWANLC-3-FPD_INCOMPATIBLE: FPD ID=[int] image in this FPD package is 
for revision [int].x boards. It is incompatible with current board revision of 
[int].[int]

Explanation This FPD package does not contain images that are compatible with the current line card revision.

Recommended Action Perform the FPD upgrade operation with a newer version of an FPD image package that is compatible with the Cisco IOS software that is operating on the switch. Consult with the FPD image package section of the Cisco IOS software release note to confirm that your line card revision is supported for a particular release.

Error Message    %CWANLC-3-CWANLC_EARL_VERSION_NOTICE: CWAN receives mismatch Earl 
version notification. New Earl[int] vs Earl[int]

Explanation The RP determined through an SCP find operation that the version of the EARL switching engine on the module has changed. This message occurs during a switchover operation. The version of the EARL switching engine is specified in the message text.

Error Message    %CWANLC-3-FATAL: [chars]

Explanation The OSM encountered a fatal error.

Error Message    %CWANLC-3-FPD_INCOMPATIBLE: FPD ID=[int] image in this FPD package is 
for revision [int].x boards. It is incompatible with current board revision of 
[int].[int]

Explanation This FPD package does not contain images that are compatible with the current board revision.

Recommended Action Perform the FPD upgrade operation with a newer version of the FPD image package that is compatible with the running Cisco IOS software. Consult with the FPD image package section of the Cisco IOS software release note to confirm if your board revision is supported for a particular release.

Error Message    %CWANLC-3-IPCPORT: Failed to %s IPC port '%s', error %s

Explanation The line card failed to create a port for communication with the route processor.

Error Message    %CWANLC-3-LTL_NOPPEPORTMAP: Failed to retrieve default port mapping 
for packet processor [int]

Explanation The line card software initialization was not completed correctly.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWANLC-3-TVPN_NOMEM: Failed to start vpn, not enough memory

Explanation The OSM could not start VPN due to insufficient memory.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

CWANLC-5

Error Message    %CWANLC-5-NOSCPPING: Linecard has not sent SCP PING responses for too 
long

Explanation The SCP ping mechanism is used by the RP and SP processors to monitor whether the line card that is executing Cisco IOS is in a healthy state. This SCP ping response has not been sent by the line card for a long time; the line card has exported its context information to the RP and may be power cycled. The exported context is available in the output of the show diag command.

Recommended Action Save the show diag command output and contact your Cisco technical support representative if the line card is reset.

CWANLC_ATM Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN ATM module (CWANLC_ATM) messages.

CWANLC_ATM-3

Error Message    %CWANLC_ATM-3-NOVPSPACE: [chars]: out of VP space for VPI [dec]

Explanation Out of virtual paths (VPs) on the segmentation and reassembly (SAR) engine.

Error Message    %CWANLC_ATM-3-VCCLOSEFAIL: [chars]: Failed to remove VC [dec]/[dec] 
cause [int]

Explanation An attempt to remove a virtual circuit on the module failed.

CWAN_POSEIDON Messages

This section contains Optical Services Module (OSM) GE-WAN Route Processor (RP) driver messages.

Error Message    %CWAN_POSEIDON-6-ALARM_INFO: [chars] [chars] [chars] [chars] [chars]

Explanation This message is generated whenever an alarm is present in the system and the alarm status has been reported to the RP, or an alarm has been removed from the system and the alarm status has been reported to the RP.

Recommended Action This is an informational message only. No action is required.

CWAN_QINQ Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN QinQ (CWAN_QINQ) messages.

CWAN_QINQ-3

Error Message    %CWAN_QINQ-3-CWAN_POCH_QINQ_NULL_EGRESS: [chars] QinQ Ether VC have 
received invalid egress assignment on phyport [chars]for trunk encapsulation dot1q 
[int]

Explanation The port channel QinQ Ether VC subinterface being configured contains an invalid egress port assignment. The egress traffic of the OSM port will be stopped for this EVC.

Recommended Action Copy the message exactly as it appears on the console or in the system log. At the line card, enter the show cwan qinq command to gather data that may help identify the cause of the error. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_QINQ-3-CWAN_QINQ_TRUNK_DATAINCONSISTENCY: QinQ data integrity 
check failed for bridge-vlan [int] dot1q [int] using trunk encapsulation dot1q 
[int], existing record shows mapping with encapsulation dot1q [int].

Explanation A data integrity error related to QinQ was detected while a trunk was being configured for the bridge VLAN that is indicated in the message text. The error will be ignored, and the QinQ update will proceed normally.

Recommended Action Enter the show cwan qinq command on the module. Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

CWAN_RP Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN route processor driver (CWAN_RP) messages.

CWAN_RP-0

Error Message    %CWAN_RP-0-LCLOG_MSG : slot [dec]/[dec]: [chars]

Explanation An error has occurred on a module. The slot and CPU number are indicated after the CWAN_RP-0-LCLOG_MSG text. The error message that appears after the slot number is the original message from the module.

Recommended Action Follow any instructions provided in the error message text. If no instructions are provided, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

CWAN_RP-1

Error Message    %CWAN_RP-1-LCLOG_MSG : slot [dec]/[dec]: [chars]

Explanation An error has occurred on a module. The slot and CPU number are indicated after the CWAN_RP-1-LCLOG_MSG text. The error message that appears after the slot number is the original message from the module.

Error Message    %CWAN_RP-1-OVERRIDE_MAC_INVALID: [chars] has invalid 
override-mac-address.

Explanation The user issued an override MAC address that does not match the MAC address of the MSFC. This condition can occur if the configuration was moved to new hardware or the MAC address command was used on another interface. While the system automatically corrects this condition, the configuration needs to be adjusted.

Recommended Action Modify the override MAC address command in the configuration.

CWAN_RP-2

Error Message    %CWAN_RP-2-LCLOG_MSG : slot [dec]/[dec]: [chars]

Explanation An error has occurred on a module. The slot and CPU number are indicated after the CWAN_RP-2-LCLOG_MSG text. The error message that appears after the slot number is the original message from the module.

CWAN_RP-3

Error Message    %CWAN_RP-3-FAILED_CONFIG: Failed to send line card config message 
[chars] for slot [int] port [int]

Explanation The RP could not send the specified configuration message to the line card.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_RP-3-IFCFG_CMD_NOT_OWNER: Process '[chars]' waiting for 
interface configuration command ([hex]) to slot [int]/[int] without acquiring lock 
owned by process '[chars]'

Explanation A process on the RP sent a configuration command to the slot specified in the message and a different process waited for the result. This condition could cause incorrect line card configuration states.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_RP-3-LCLOG_MSG : slot [dec]/[dec]: [chars]

Explanation An error has occurred on a module. The slot and CPU number are indicated after the CWAN_RP-3-LCLOG_MSG text. The error message that appears after the slot number is the original message from the module.

Error Message    %CWAN_RP-3-MODULE_TYPE: cannot find FCI for module type [int] in slot 
[int]

Explanation An internal software error occurred while the system was detecting the module type in the specified slot. The module operation will be affected.

Error Message    %CWAN_RP-3-PROCMSG: Process msg send failed for process[dec]

Explanation An attempt to send a process message failed for the specified process.

Error Message    %CWAN_RP-3-UPGRADE_ERROR: Slot [int]: The ROMMON upgrade failed to 
complete.

Explanation An error occurred during the upgrade process.

Recommended Action If the module reloads successfully, examine the file and try the upgrade process. If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_RP-3-WAN_BRIDGING_CONFIG_EXCEEDED: The number of 
VPLS/EoMPLS/Bridging/QinQ VCs exceeded the maximum supported by the platform

Explanation The user attempted to configure more VPLS, EoMPLS, and bridging VCs than the number that is supported by the platform.

Recommended Action Review the configuration guidelines for the features that are being configured, and reduce the number of VPLS, EoMPLS, and bridging VCs to the number that is supported by the platform.

CWAN_RP-4

Error Message    %CWAN_RP-4-CONFIG_MISMATCH: Irreconcilable Configuration difference 
between Active & Standby Supervisors due to OIR/Config Event -> Reloading Standby 
Supervisor to synchronize the configuration.

Explanation An unexpected configuration difference exists between the active and standby supervisor engines.

Recommended Action The standby supervisor engine is being reloaded. No action is required.

Error Message    %CWAN_RP-4-EMPTY_CWANBAYS: FLEXWAN in slot [dec] is empty. Please 
remove the Flexwan or insert it with atleast one PA

Explanation The FlexWAN in the specified slot does not contain any port adapters.

Recommended Action The FlexWAN should be removed. This is an unsupported configuration.

Error Message    %CWAN_RP-4-IFCFG_CMD_TIMEOUT: Interface configuration command ([hex]) 
to slot [int]/[int] timed out

Explanation The RP sent a configuration command to the slot specified in the message and received no confirmation for the command.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_RP-4-INCR_CFG_SYNC_FAIL: 7600 incremental running-config sync 
for [[dec]/[dec]] failed - [chars]([dec]), Reload Standby

Explanation The specified 7600 series router incremental running configuration synchronization has failed.

Recommended Action Power cycle the redundant supervisor engine.

Error Message    %CWAN_RP-4-INVALID_UNIT: Invalid 7600 Unit: [[dec]/[dec]].

Explanation The specified 7600 series router slot and CPU are beyond the chassis limit.

Recommended Action Power cycle the redundant supervisor engine.

Error Message    %CWAN_RP-4-LCLOG_MSG : slot [dec]/[dec]: [chars]

Explanation An error has occurred on a module. The slot and CPU number are indicated after the CWAN_RP-4-LCLOG_MSG text. The error message that appears after the slot number is the original message from the module.

Error Message    %CWAN_RP-4-MODULE_CONFIG_MISSING: configuration missing for slot [int]

Explanation Some information is missing regarding the configuration of the module in the specified slot. Any startup configuration for the interfaces will not be applied. If the module in the specified slot is a FlexWAN, details about the port adapters in the FlexWAN are missing from the configuration information. This information is missing from the SLOTCACHE ROMMON variable.

Recommended Action If the module in the slot specified in the error message has not previously been inserted, it has no previous configuration; therefore, no action is required. If the configuration for the specified slot in the startup configuration is suitable for the module in that slot, after the module has loaded, manually apply the configuration by using one of the following two methods. The second method requires a system reload.

–Enter the copy nvram:startup-config system:running-config command to reapply your saved configuration and then enter the no shutdown command on all interfaces whose configuration was rejected. Enter the copy system:running-config nvram:startup-config command to save your configuration and the WAN module slot configuration.

–Enter the copy command to copy your startup configuration to a temporary location (for example, copy nvram:startup-config bootflash:tmp-config), and then enter the copy system:running-config nvram:startup-config command to update the WAN module slot configuration. Enter the copy command to restore the temporary copy of the startup configuration (for example, copy bootflash:tmp-config nvram:startup-config), and then enter the reload command to reload the system.

After using the second method, you may want to use the delete command to remove the temporary copy of the startup configuration. To prevent this condition from recurring, ensure that the SLOTCACHE variable is updated whenever modules that require it (FlexWANs, but not OSMs) are moved between slots in the chassis. The SLOTCACHE variable is updated when the running configuration is written to the startup configuration using the copy system:running-config nvram:startup-config command (or the deprecated write memory equivalent). The two methods of restoring the configuration for the module ensure that the SLOTCACHE variable is updated.

CWAN_RP-5

Error Message    %CWAN_RP-5-LCLOG_MSG : slot [dec]/[dec]: [chars]

Explanation An error has occurred on a module. The slot and CPU number are indicated after the CWAN_RP-5-LCLOG_MSG text. The error message that appears after the slot number is the original message from the module.

CWAN_RP-6

Error Message    %CWAN_RP-6-ADF_FILE: Slot [int]: Using VPN-SM Upgrade File: "[chars]"

Explanation The system is booting the specified upgrade image for the VPN Services Module.

Recommended Action No action is required.

Error Message    %CWAN_RP-6-AUX_FILE: Slot [int]: Found VPN-SM Firmware in File: 
"[chars]"

Explanation The file specified in the message was found and will be loaded instead of the bundled image by the VPN Services Module.

Recommended Action No action is required.

Error Message    %CWAN_RP-6-LCLOG_MSG : slot [dec]/[dec]: [chars]

Explanation An error has occurred on a module. The slot and CPU number are indicated after the CWAN_RP-6-LCLOG_MSG text. The error message that appears after the slot number is the original message from the module.

Error Message    %CWAN_RP-6-LC_RESET: The RP is reloaded, resetting slot [dec] is 
necessary. Please ignore errors if any, till the linecard comes up.

Explanation If the system is running Catalyst operating system software on the supervisor engine and Cisco IOS software on the MSFC, the WAN line cards that power up before the RP powers up will be reset automatically.

Recommended Action This is an informational message only. No action is required.

Error Message    %CWAN_RP-6-NO_LC_IMAGE: Line card image in slot [dec] for card_id [dec] 
is not bundled with IOS.

Explanation The line card in the specified slot will be powered down to prevent it from running an image that is not supported by the RP. If the line card image is compatible with the image running on the RP, there might be another problem with the software.

Error Message    %CWAN_RP-6-OUT_OF_RESOURCE: [chars] configuration has exceeded 
available internal resources.

Explanation The resources required for configuration are no longer available. They may have been acquired by another application.

Recommended Action If the requested resources have not been allocated to another application, contact your Cisco technical support representative for further assistance.

Error Message    %CWAN_RP-6-OVERRIDE: Slot [int]: ...Overriding Intrinsic VPN-SM 
Firmware.

Explanation The specified image will be used instead of the bundled image.

Recommended Action No action is required.

Error Message    %CWAN_RP-6-UPGRADE_COMPLETE: Slot [int]: ROMMON upgrade complete. 
Reset the card for the changes to take effect.

Explanation The ROMMON upgrade has completed successfully. The module must be reloaded for the changes to take effect.

Recommended Action No action is required.

CWAN_RP-7

Error Message    %CWAN_RP-7-LCLOG_MSG : slot [dec]/[dec]: [chars]

Explanation An error has occurred on a module. The slot and CPU number are indicated after the CWAN_RP-7-LCLOG_MSG text. The error message that appears after the slot number is the original message from the module.

CWAN_SLOT Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN slot (CWAN_SLOT) messages.

CWAN_SLOT-1

Error Message    %CWAN_SLOT-1-CF_ADDFAILED: Failed to register chkpt client, client = 
%d

Explanation The checkpoint facility client could not be registered.

Error Message    %CWAN_SLOT-1-CF_NOBUF: Failed to get chkpt buffer, client = %d

Explanation The checkpoint facility could not obtain buffer memory.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

CWAN_SP Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router WAN switch processor (CWAN_SP) messages.

CWAN_SP-3

Error Message    %CWAN_SP-3-INIT_FAIL: Failed to allocate [dec] bytes memory needed for 
CWAN SP module initialization

Explanation A memory allocation failure has occurred during initialization of WAN SP module.

Recommended Action Upgrade to a higher memory size on the switch processor (SP).

CWAN_SP-4

Error Message    %CWAN_SP-4-UNKNOWN_PW: Unknown CWAN pseudo wire on vlan [dec], port 
[dec]/[dec]

Explanation An unknown WAN pseudowire is being used.

CWAN_SPA Messages

This section contains shared port adapter (SPA) on OSR messages.

Error Message    %CWAN_SPA-3-CREATION_FAILURE: slot=[dec] subslot=[dec], 
spa_type=[hex], lc_type=[hex].

Explanation An attempt to create a SPA object has failed.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_SPA-3-DIAG_CONFIG: [chars] did not complete [dec]/[dec]

Explanation An error has occurred during diagnostic test.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_SPA-3-INVALID_DATA_INSTANCE: interface type [chars], slot [dec] 
port [dec] vc [dec] : [chars]

Explanation The data required to support the specified interface is not available.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_SPA-3-INVALID_IF_INDEX: index= [dec], cardType=[hex], 
spaType=[hex], slot [dec] subSlot [dec] slotunit [dec] vc [dec]

Explanation The index for the interface is not valid.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_SPA-3-INVALID_INDX_RANGE: index1= [dec], index2= [dec], 
maxIndex= [dec]

Explanation Invalid index range.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_SPA-3-MEM_ALLOC_ERROR: [chars]

Explanation A memory allocation error has occurred.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_SPA-3-NULL_SPA_PTR:

Explanation The pointer to a SPA object is null.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_SPA-3-NULL_VFT: [chars] virtual function table is not 
initialized. spaType=[hex]

Explanation A required function table is not initialized.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_SPA-3-NULL_VFUNC: [chars] vector is not initialized. 
spaType=[hex]

Explanation A required function vector is not initialized.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_SPA-3-POWER_CYCLE: [chars] occurred on Shared Port Adapter 
[int]/[int]

Explanation An error has occurred that will cause the shared port adapter to be power cycled.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWAN_SPA-3-SPA_CREATION_FAILURE: slot=[dec] subslot=[dec], 
PID=[chars] lc_type=[hex].

Explanation An attempt to create a SPA object has failed.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

CWPA Messages

This section contains Catalyst 6500 series switch and Cisco 7600 series router port adapter module (CWPA) messages.

CWPA-2

Error Message    %CWPA-2-BAD_HWVERS: Unable to determine board hardware version

Explanation The module software cannot read the module hardware version. This condition indicates a hardware error.

Error Message    %CWPA-2-PAOIR: Port adapter OIR not supported, reloading

Explanation An OIR operation occurred on the port adapters of the specified module, but OIR is not supported on the port adapter. This error has caused the module to fail and reload.

Recommended Action Do not attempt OIR on the port adapters of the specified module.

Error Message    %CWPA-2-PA_VOLFAIL: Port adapter [dec]V failed, Reloading flexwan

Explanation The module encountered an error involving power delivery to the module. Probable causes for this error are an environmental condition, an overtemperature condition, or inconsistent voltage to the module.

Recommended Action Verify that the input voltage and the temperature of the module are within acceptable ranges.

Error Message    %CWPA-2-WHICH_INT: Unexpected [chars] interrupt, INT status = [hex]

Explanation The module specified in the error message has encountered an unexpected interrupt.

CWPA-3

Error Message    %CWPA-3-DIAGFAIL: Failed to handle diag [chars] [dec]

Explanation The module failed to execute a diagnostics command.

Error Message    %CWPA-3-PROCCREATEFAIL: Failed to create [chars] process

Explanation A module failed to create a process that is necessary for proper functioning of the module.

Recommended Action If a statistics export process was not created, check the I/O rate and the bytes that are getting incremented in the show interface command output for the nonchannelized interfaces on the FlexWAN and Enhanced FlexWAN modules. You can also get the statistics from the show interface acc command output or the show interface stats command output. Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

CWPA-4

Error Message    %CWPA-4-HEADER_TOO_BIG: Needs [dec] bytes, with only [dec] bytes 
available. Packet size [int], received from [chars], buffer [hex] packet start 
[hex]:

[hex]:[hex] [hex] [hex] [hex] [hex] [hex] [hex] [hex]

[hex]:[hex] [hex] [hex] [hex] [hex] [hex] [hex] [hex]

Explanation A packet was sent from the port adapter to either the route processor or the line card. That packet did not have enough available space to append the header. A new particle has been linked to the packet to store the header.

Recommended Action No action is required.

CWPABRIDGE Messages

This section contains CWPA bridging messages.

Error Message    %CWPABRIDGE-3-BADLTL: [chars] got bad LTL index [hex] for vlan [int] 
ckt_id [int] sent from RP

Explanation The RP has provided the line card with an invalid value for the local target logic (LTL) index value.

Recommended Action If the bridging traffic stops going through, copy the message exactly as it appears on the console or in the system log. At the RP console exec prompt, enter the following commands:

show log,
show cwan bridge,
show atm vlan,
show mac-address-table dynamic detail,
show cwan ltl

The output of these commands will enable the engineer to gather more information about the condition. Contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message    %CWPABRIDGE-3-NOCLONEDPAK: Unable to allocate pak header for cloned 
pak

Explanation A line card is not able to allocate a pak header for a cloned pak that is used for flooding packets among bridged WAN links.

Recommended Action On the Cisco support website, use the online Software Advisor and check the release notes for the code you are running to determine the minimum amount of memory. If you have sufficient memory and are still seeing this error message, load the previous image on the unit to return the unit to an operational state and retrieve the information needed to report this problem. Copy the contents of the line card's crashinfo data from the cwan slot/bay bootflash: command, where slot and bay belong to the line card. When you open a TAC case, provide the line card's crashinfo data and the output of the show tech command from the router.

CWRPSPA Messages

This section contains messages for shared port adapters (SPAs) on the Catalyst 6500 Series Switch and Cisco 7600 Series Router WAN route processor (RP).

CWRPSPA-3

Error Message    %CWRPSPA-3-HWIDB_FAILURE: Creation: slot [dec] subSlot [dec] port 
[dec] vc [dec]

Explanation Failed to create a hardware interface descriptor block (HWIDB).

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWRPSPA-3-INVALID_PORT_NUM: slot=[dec] port=[dec], hwidbType=[hex], 
max_port_num=[dec], LCtype=[hex]

Explanation The port number is out of range.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWRPSPA-3-MAX_SPA: Power to IPSEC-SPA-2G in [chars] is denied because 
it has exceeded the number allowed([dec])

Explanation The number of IPSEC-SPA-2G port adapters in a chassis is limited. This message displays when the number of IPSEC-SPA-2G port adapters in the chassis has exceeded the limit.

Recommended Action Use only the number of supported IPSEC-SPA-2G port adapters.

Error Message    %CWRPSPA-3-NO_HOST_INFO: slot [dec] subSlot [dec], spaType [hex]

Explanation Failed to get information about the host line card.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

CWRPSPA-4

Error Message    %CWRPSPA-4-SPA_CMD_NO_RESP: [chars]: No response for interface 
configuration command [int]

Explanation A timeout occurred while the RP was waiting for a response from the line card. This condition may occur when the line card CPU is too busy to respond to the configuration command.

Recommended Action Retry the configuration command.

Error Message    %CWRPSPA-4-SPA_RESP_CMD_MISMATCH: [chars]: Expecting response to 
interface configuration command [int] but received response to command [int].

Explanation An internal synchronization error occurred while configuring the interface. The configuration may not have succeeded.

Recommended Action Check that the running configuration for the interface is correct. If this message occurred on the standby, try reloading the standby to ensure that its configuration is in sync. If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

CWRPSPA-6

Error Message    %CWRPSPA-6-CARDRELOAD: Module [int] reload due to SPA insert in 
[int]/[int].

Explanation When inserting a SPA on the specified module, the module resets.

Recommended Action This message is informational. No action is required.

CWSLC Messages

This section contains WAN SiByte Module (CWSLC) messages.

CWSLC-3

Error Message    %CWSLC-3-DIAGFAIL: Failed to handle diag [chars] [dec]

Explanation The module failed to execute a diagnostics command.

Error Message    %CWSLC-3-DIAGSKIP: Skipped diag for port [dec]

Explanation The module skipped diagnostics for the specified port.

Error Message    %CWSLC-3-DIAGWARNING: Backplane DIP switches settings incorrect

Explanation The backplane DIP switches need to be set properly.

Recommended Action Refer to the 7600 SIP and SPA Hardware Installation Guide for information about how DIP switches must be set.

Error Message    %CWSLC-3-IPCALLOCFAIL: Failed to allocate IPC buffer [chars]

Explanation An Enhanced FlexWAN module failed to allocate a buffer for communication with the route processor (MSFC).

Error Message    %CWSLC-3-IPCSENDFAIL: Failed to send IPC message [chars]

Explanation An Enhanced FlexWAN module failed to send a message to the route processor (MSFC).

Error Message    %CWSLC-3-LC_ENCAP_UPDATEFAIL: Could not update encapsulation on 
[chars] to [int]

Explanation The line card failed to update the new encapsulation that was requested. The interface data structures could not be temporarily locked to perform the encapsulation change

Recommended Action If the interface does not come up with the new encapsulation, remove and reconfigure the encapsulation on the interface. If the error persists after a few attempts at reconfiguration, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

CWTLC Messages

This section contains WAN Optical Services Module (CWTLC) messages.

CWTLC-0

Error Message    %CWTLC-0-FATAL_EXCEPTION: [chars]

Explanation The OSM encountered a fatal exception.

CWTLC-2

Error Message    %CWTLC-2-FATAL_ATM: [chars]

Explanation The OSM encountered a fatal line management interrupt. This error is not recoverable and will cause the system to fail.

Error Message    %CWTLC-2-PCITIMEOUT: Fatal Local I-O Bus [dec] Timeout Addr = [hex]

Explanation The OSM encountered a PCI timeout.

Error Message    %CWTLC-2-PLIM_RX: [chars]

Explanation The OSM encountered an FPGA error that caused a sequence error.

Error Message    %CWTLC-2-SLAVEPCI: [chars]

Explanation The OSM encountered a PCI error.

Error Message    %CWTLC-2-TESTCRASH: [chars]

Explanation The user entered a command that caused the module to fail.

Recommended Action No action is required.

CWTLC-3

Error Message    %CWTLC-3-ATMTXFIFO: [chars]

Explanation The OSM encountered an error with the FPGA that has caused the FIFO queue to exceed the maximum limit. This condition will cause the system to fail.

Error Message    %CWTLC-3-CONST_SWITCHING_BUS_INTERFACE_ASIC_ERR: Constellation 
Switching Bus Interface Asic [[dec]] error: [chars]

Explanation The CWTLC switching bus interface ASIC received an error.

Recommended Action If traffic recovers, no action is required. Otherwise, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC-3-CONST_SWITCHING_BUS_INTERFACE_ASIC_HWERR: Constellation 
Switching Bus Interface Asic [[dec]] HW error: [chars]

Explanation The CWTLC switching bus interface ASIC received a hardware error and will be reset.

Error Message    %CWTLC-3-DMA_ENGINE_ASIC_ERR: DMA Engine Asic [[dec]] error: [chars]

Explanation The CWTLC DMA engine ASIC received an error.

Error Message    %CWTLC-0-DMA_ENGINE_ASIC_FATAL_ERR: DMA Engine Asic[[dec]] fatal 
error: [chars]

Explanation The CWTLC DMA engine ASIC received a fatal error.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC-3-ERR_DETAIL: [chars]

Explanation This message provides additional error details for a previous message, which may be of use to your technical support representative.

Recommended Action Follow the instructions for any system messages preceding this one and be sure to include the text from this error.

Error Message    %CWTLC-3-EXCEPTION_ERR: [chars]

Explanation The OSM encountered an error exception.

Error Message    %CWTLC-3-FABRIC_INTERFACE_ASIC_FATAL: OSM Fabric Interface ASIC Fatal 
Error. ERROR CODE: [chars]

Explanation The OSM fabric interface ASIC received a fatal error.

Error Message    %CWTLC-3-FABRIC_INTERFACE_ASIC_PXF: CWAN PXF Client [[dec]] Not 
Running

Explanation An ASIC device on the OSM has detected that the designated PXF client is not running.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC-3-FR_BAD_BRIDGING: Frame Relay: old bridge-vlan([int]) or new 
bridge-vlan([int]) on the bridged interface [chars] is malformed

Explanation This is an unexpected update from the route processor and should be ignored.

Recommended Action This is an informational message only. No action is required.

Error Message    %CWTLC-3-FR_INTLEVEL: unexpected interrupt level invocation of 
frame-relay handler:[chars] if_number([dec]) dlci([dec])

Explanation Some feature code mistakenly invoked the module Frame Relay handler, which is designed to run at process level. This condition may lead to data corruption and a module failure.

Error Message    %CWTLC-3-LTL_ERR: Inconsistent port selection [hex] assigment for 
PXF([dec]) Vlan([dec]) on PXF([int])

Explanation The port selection information stored in the database is not valid.

Recommended Action Shut down the interface VLAN and restart the interface VLAN.

Error Message    %CWTLC-3-MCAST_REPL_ENGINE_FATAL: Multicast Replication Engine Asic 
Fatal Error. Resetting ASIC.

Explanation The OSM multicast replication engine ASIC received a fatal error.

Error Message    %CWTLC-3-MEDUSA_FATAL: OSM Medusa ASIC Fatal Error. ERROR CODE: 
[chars]

Explanation The OSM Medusa ASIC received the specified fatal error.

Recommended Action No action is required if traffic recovers. If traffic does not recover, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC-3-MEDUSAPXF: CWAN PXF Client [[dec]] Not Running

Explanation An ASIC device on the OSM has detected that the specified PXF client is not running.

Error Message    %CWTLC-3-NOMEM: [chars]

Explanation The OSM could not obtain statistics due to depleted memory.

Error Message    %CWTLC-3-NO_STATID: PXF([dec]): no stat_id is available for statistics 
collection

Explanation The OSM has used up all resources for statistics collection. No additional resources are available for further statistics collection.

Recommended Action Reduce the number of features configured on the specified PXF. If conditions warrant, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC-3-OLDIOFPGA: Upgrade your I/O FPGA

Explanation The OSM has an earlier release of the I/O FPGA software.

Recommended Action Contact your Cisco technical support representative to upgrade the I/O FPGA software.

Error Message    %CWTLC-3-PLIM_TX: [chars]

Explanation The OSM encountered an FPGA error that caused a sequence error. The module will attempt to recover from the error.

Recommended Action If the system recovers, no action is required. If the system does not recover, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC-3-PORTERROR: Port control error, cmd=[chars], port=[dec]

Explanation The port control command function has failed.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC-3-SECPAIRINT: Unexpected VA/Toaster interrupt from second pair

Explanation The OSM experienced an unexpected interrupt.

Error Message    %CWTLC-3-TITANFATAL: Titan Fatal Error. Resetting ASIC.

Explanation The OSM Titan ASIC received a fatal error.

Error Message    %CWTLC-3-TMC_STATID_INCONSISTENCY: PXF([dec]):Inconsistent stats 
id([hex]) [int] packets dropped.

Explanation The WAN module received inconsistent statistics from the PXF. The PXF reported that a packet was dropped, but the PXF did not report the correct packet count.

Error Message    %CWTLC-3-TMTRIE_ALLOC_FAILED: Failed to allocate toaster mtrie nodes.

Explanation The system encountered an error while it was attempting to allocate memory from a WAN OSM component.

Recommended Action Reduce the number of routes associated with a VRF identifier or upgrade the WAN OSM to a higher version.

Error Message    %CWTLC-3-UNSUPPORTED_LABEL_RANGE: The maximum label range configured 
for this system exceeds

the [int] limit supported by the OSM module.

Explanation The MPLS label range configured for this system is not supported. The maximum label range limit is specified in the message.

Recommended Action Change the maximum MPLS label range by entering the mpls label range command.

Error Message    %CWTLC-3-VTMS: [chars]

Explanation The OSM could not schedule the wheel entry. The reason for the error is specified in the error message text.

Error Message    %CWTLC-3-VTMSQ_NOTIDLE: Queue not idle when modifying Q([hex])

Explanation The VTMS queue was in the process of being modified for a change in QoS configuration, but packets were still going through the queue. When the queue is being modified, there is usually no traffic in the queue.

CWTLC-4

Error Message    %CWTLC-4-ASIC_RESET: Reset asics - [chars]

Explanation The ASICs on the OSM are resetting. System traffic should recover and continue normally after the module resets.

Recommended Action No action is required.

Error Message    %CWTLC-4-CONST_SWITCHING_BUS_INTERFACE_ASIC_CONFIG_ERR: Constellation 
Switching Bus Interface Asic [[dec]] configuration failed after [dec] retries.

Explanation The CWTLC switching bus interface ASIC failed to be configured correctly.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC-4-MEDUSAERROR: Medusa Error. [chars]

Explanation The CWTLC Medusa ASIC received a recoverable error.

Error Message    %CWTLC-4-PINNACLE_OLDIOFPGA: Link negotiation maybe be affected, 
upgrade I/O FPGA

Explanation The system detected an earlier release of the I/O FPGA software. The I/O FPGA software needs to be upgraded to the latest release.

Recommended Action Upgrade the I/O FPGA software to the newest release. If you require assistance, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC-4-PORT_ASIC_OLDIOFPGA: Link negotiation maybe be affected, 
upgrade I/O FPGA

Explanation An earlier version of the I/O FPGA software has been detected.

Recommended Action Upgrade the I/O FPGA software to the latest version. If you require assistance, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC-4-TMC_INVALID_STATID: PXF:Invalid-Statid ([dec]) for vc [int] 
under interface [int]

Explanation The OSM has encountered an internal error while setting up the statistics system.

CWTLC-5

Error Message    %CWTLC-5-BUS_SEQ_ERR: Constellation bus Sequence Error. Resetting port 
ASICS.

Explanation The SP detected a sequence error on the backplane bus of the OSM. The system called a reset sequence from the EARL to recover from this error. System traffic should recover and continue normally.

Recommended Action If traffic recovers, no action is required. If traffic does not recover, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC-5-DATAPATH_RECOVERY_PATCH: EARL reset patch invoked.

Explanation The ASICs on the OSM were reset so that the module could recover from a bus sequence error. This condition usually occurs under heavy traffic with HA-related switchover or a module OIR operation. System traffic should recover and continue normally.

Error Message    %CWTLC-5-FABRIC_INTERFACE_ASIC_RE_INIT: Fabric Interface Asic 
Re-initialize.

Explanation The OSM fabric interface ASIC is being reinitialized because of a system backplane bus sequence error, a fatal ASIC error, or a line card error.

Error Message    %CWTLC-5-MEDUSA_RE_INIT: Medusa Re-initialize.

Explanation The OSM Medusa ASIC is being reinitialized because of a system backplane bus sequence error or a fatal ASIC error on the module itself.

Error Message    %CWTLC-5-PENDING_PATCH: Invoke pending data recovery patch.

Explanation The ASICs on the OSM line card has been reset so that it can recover from backplane switching bus sequence errors or local hardware ASIC errors. This condition is usually occurs under stress trafficwith HA-related switchover or a line card OIR operation. System traffic should recover and continue normally.

CWTLC-6

Error Message    %CWTLC-6-FABRIC_INTERFACE_ASIC_MODECHANGE: Fabric Interface Asic 
switching bus Mode changed to [chars]

Explanation The supervisor engine has changed the CWTLC fabric interface ASIC switching bus mode.

Recommended Action No action is required.

CWTLC_ATOM Messages

This section contains Any Transport over MPLS messages for WAN Optical Services Modules (CWTLC_ATOM).

CWTLC_ATOM-3

Error Message    %CWTLC_ATOM-3-INTFID_ERR: The internal interface ID [hex] for the AToM 
interface [chars] is invalid for the connection ID [hex]

Explanation The internal interface ID that is required by the OSM to establish an AToM connection is either invalid or is mismatched with the control plane MPLS data structure for this connection. The current interface ID of the OSM has lost its synchronization with the interface ID of the control plane for this connection. This condition is usually caused by unfavorable network conditions such as a failover operation and can occur during normal system operation.

Recommended Action Enter the appropriate AToM commands for either the Frame Relay over MPLS, Cell Relay over MPLS, AAL5 over MPLS, or Frame Relay local switching to remove the AToM connection, then add the connection again. Performing this action once should successfully reestablish the connection.

Error Message    %CWTLC_ATOM-3-OSM_BB1_CONFIG_UNSUPPORTED: Attempt to configure Frame 
Relay over MPLS or Frame Relay localswitching on a non-enhanced OSM

Explanation Frame Relay over MPLS and Frame Relay local switching features are supported only on enhanced Optical Services Modules. Nonenhanced OSMs do not support these features.

Recommended Action Remove the configuration of the unsupported features, or upgrade this module to an enhanced OSM.

CWTLC_CHOC Messages

This section contains Cyclops Channelized OC48/OC12 (CWTLC_CHOC) messages.

CWTLC_CHOC-3

Error Message    %CWTLC_CHOC-3-HWERROR: [chars]

Explanation The module hardware has experienced the specified error.

CWTLC_CHOC_DSX Messages

This section contains Optical Services Module (OSM) CHOC DSX LC common messages.

Error Message    %CWTLC_CHOC_DSX-3-HWERROR: [chars]

Explanation A hardware error involving the OSM line card has occurred.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

CWTLC_CHOCX Messages

This section contains Optical Services Module (OSM) Channelized OC12/OC3 module (CWTLC_CHOCX) messages.

CWTLC_CHOCX-3

Error Message    %CWTLC_CHOCX-3-HWERROR: [chars]

Explanation The module hardware has experienced the specified error.

CWTLC_GEWAN Messages

This section contains Gigabit Ethernet WAN module (CWTLC_GEWAN) messages.

CWTLC_GEWAN-3

Error Message    %CWTLC_GEWAN-3-FPGA_PROG_FAILED: [chars] FPGA initialization failed 
due to [chars]

Explanation The FPGA could not be initialized. The cause of this condition is specified in the message text on the console or in the system log. As a result of this condition, the device is not operational and has been disabled.

Recommended Action Reload the line card. If the problem persists, copy the message exactly as it appears on the console or in the system log. Enter the show module command to gather data that may help identify the cause of the error. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC_GEWAN-3-GEMAC_9K_MODE_FIX_FAILED: Fix for 9k buffer mode failed 
for GEMAC[[dec]]

Explanation An error has occurred while the system was setting the GEMAC component of the Gigabit Ethernet WAN module in 9,000-buffer mode (a buffer mode that supports jumbo frames). This condition occurred on the port specified in the error message.

Error Message    %CWTLC_GEWAN-3-GEMAC_INIT_FAILED: Device initialization failed for 
GEMAC[[dec]]

Explanation An error occurred during initialization of the GEMAC device.

Error Message    %CWTLC_GEWAN-3-IF2PORT: Cannot determine port from interface [dec] for 
operation [dec] with [[enet]]

Explanation The port number could not be determined from the given interface number.

Error Message    %CWTLC_GEWAN-3-MAC_OP_BAD: Unknown MAC address operation [dec] with 
[[enet]] on port [dec]

Explanation The specified MAC address operation is unknown and cannot be performed.

Error Message    %CWTLC_GEWAN-3-PORT_AUTONEG_FAIL: Failed to [chars] auto-negotiation 
[chars] on port [dec]

Explanation The enabling/disabling of the auto-negotiation functionality on a GE-WAN port has failed.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC_GEWAN-3-PORT_CMD_FAIL: Port [chars] failed on port [dec]

Explanation A GE-WAN port command has failed.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC_GEWAN-3-TABLE_ADD_REMOVE_FAILED: MAC address table [chars] with 
[[enet]] failed on port [dec]

Explanation The addition or removal of a MAC address from the MAC address table has failed.

Error Message    %CWTLC_GEWAN-3-ZICO_INIT_FAILED: Device initialization failed for Zico 
FPGA[[dec]]

Explanation An error occurred during initialization of the protocol converter FPGA.

CWTLC_GEWAN-5

Error Message    %CWTLC_GEWAN-5-GEMAC_INTR: [chars]: [chars]

Explanation The GEMAC component of the Gigabit Ethernet WAN module caused an error interruption.

Recommended Action Reload the module. If the problem persists, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC_GEWAN-5-LINKFPGA_INTR: Index[[dec]] Cause[[hex]]: [chars]

Explanation The link FPGA component of the Gigabit Ethernet WAN module caused an error interruption to occur.

CWTLC_QOS Messages

This section contains Optical Services Module (OSM) supervisor engine line card QoS messages.

Error Message    %CWTLC_QOS-3-CHUNK_INIT_FAIL: [chars]: [chars] allocation failed

Explanation The OSM detected a memory allocation failure. The installed amount of memory could be insufficient for the software features that are configured.

Recommended Action If this message appears continuously, a memory upgrade might be required.

Error Message    %CWTLC_QOS-3-CHUNK_MALLOC_FAIL: [chars]: chunk_malloc for [chars] 
failed

Explanation The OSM detected a memory allocation failure. The installed amount of memory could be insufficient for the software features that are configured.

Recommended Action If this message appears continuously, a memory upgrade might be required.

Error Message    %CWTLC_QOS-3-MISC: [chars]: [chars] [dec]

Explanation The OSM detected the software error event that is specified in the message text.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC_QOS-4-STATS_CLASS_INFO_INVALID: Stats process found invalid 
class_info [[hex]], stat_type [[hex]] caller_pc [[hex]] caller_pc1 [[hex]].

Explanation The OSM has detected invalid class data. This condition is transient when the policy map is modified and the update is propagated to the OSM.

Recommended Action If this message appears continuously, reset theline card by entering the hw-module module <> reset command. Copy the message exactly as it appears on the console or in the system log. Enter the show tech-support command to gather data that may help identify the cause of the error. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

Error Message    %CWTLC_QOS-3-WRED_CLASS_INDEX_NOT_FOUND: sub-class limit has exceeded

Explanation The OSM supports only 29 WRED classes: 8 CS, 12 AF, 1 EF, and 8 user-defined DSCP values.

Recommended Action Refer to the technical documentation for more information about WRED configurations on the OSM.

CWTLC_RP Messages

This section contains WAN Toaster-based module route processor (CWTLC_RP) messages.

CWTLC_RP-3

Error Message    %CWTLC_RP-3-TMEM_IMPROPER_SEL: Improperly nested PXF [int] memory 
select/deselect at nested level [int]. Value stored with select ([hex]) does not 
match the value passed with deselect ([hex])

Explanation The last PXF select operation was not followed by a deselect operation.

Bias-Free Language

Results

Chapter: CONST_V6 through CWTLC_RP

CONST_V6 Messages

CONST_V6-5

CONTROLLER Messages

COPTMONMIB Messages

COPTMONMIB-3

Cougar Messages

CPU_INTF_FPGA Messages

CPU_INTF_FPGA-2

CPU_INTF_FPGA-3

CPU_INTF_FPGA-4

CPU_INTF_FPGA-5

CPU_MONITOR Messages

CPU_MONITOR-2

CPU_MONITOR-3

CPU_MONITOR-6

CRYPTO Messages

CRYPTO-3

CRYPTO-4

CRYPTO-5

CRYPTO-6

CRYPTO_HA Messages

CRYPTO_HA-3

CRYPTO_HA-6

CRYPTO_HA_IKE Messages

CRYPTO_HA_IKE-3

CRYPTO_HA_IKE-4

CRYPTO_HA_IPSEC Messages

CRYPTO_HA_IPSEC-3

CRYPTO_HA_IPSEC-4

CRYPTO_RSA_ISSU Messages

CRYPTO_RSA_ISSU-3

CSG Messages

CSG-3

CSG-4

CSG-6

CSM_SLB Messages

CSM_SLB-4

CT3 Messages

CTS Messages

CTS-0

CTS-1

CTS-2

CTS-3

CTS-4

CTS-5

CTS-6

CTS-7

CTS_HA Messages

CTS_HA-3

CTS_HA_ISSU Messages

CTS_HA_ISSU-3

CTS_HA_ISSU-6

CWAN_ALARM Messages

CWAN_ALARM-6

CWAN_ATM Messages

CWAN_ATM-3

CWAN_ATM-5

CWAN_ATOM-HA Messages

CWAN_ATOM-HA-2

CWAN_ATOM-HA-3

CWAN_CHOC Messages

CWAN_CHOC-4

CWAN_CHOC_DSX Messages

CWAN_CHOC_DSX-3

CWAN_CT3 Messages

CWAN_CT3-3

CWAN_FWD_TABLES Messages

CWAN_FWD_TABLES-3

CWAN_HA Messages

CWAN_HA-2

CWAN_HA-3

CWAN_HA-4

CWAN_HAL Messages

CWAN_HAL-3

CWAN_HAL-4

CWAN_IFMGR Messages