Implementing LPTS

LPTS Overview

Local Packet Transport Services (LPTS) maintains tables describing all packet flows destined for the secure domain router (SDR), making sure that packets are delivered to their intended destinations.

LPTS uses two components to accomplish this task: the port arbitrator and flow managers. The port arbitrator and flow managers are processes that maintain the tables that describe packet flows for a logical router, known as the Internal Forwarding Information Base (IFIB). The IFIB is used to route received packets to the correct Route Processor for processing.

LPTS interfaces internally with all applications that receive packets from outside the router. LPTS functions without any need for customer configuration. However, the policer values can be customized if required. The LPTS show commands are provided that allow customers to monitor the activity and performance of LPTS flow managers and the port arbitrator.

LPTS Policers

In Cisco IOS XR, the control packets, which are destined to the Route Processor (RP), are policed using a set of ingress policers in the incoming ports. These policers are programmed statically during bootup by LPTS components. The policers are applied based on the flow type of the incoming control traffic. The flow type is determined by looking at the packet headers. The policer rates for these static ingress policers are defined in a configuration file, which are programmed on the route processor during bootup. You can change the policer values based on the flow types of these set of ingress policers. You are able to configure the rate per policer per node.

Configuration Example

Configure the LPTS policer for the OSPF and BGP flowtypes with the following values:

  • ospf unicast default rate 200

  • bgp configured rate 200

  • bgp default rate 100 

Router#configure
Router(config)#lpts pifib hardware police
Router(config-pifib-policer-global)#flow ospf unicast default rate 200
Router(config-pifib-policer-global)#flow bgp configured rate 200
Router(config-pifib-policer-global)#flow bgp default rate 100
Router (config-pifib-policer-global)#commit

Running Configuration

lpts pifib hardware police
flow ospf unicast default rate 200
flow bgp configured rate 200
flow bgp default rate 100
!

Verification

Router#show run lpts pifib hardware police
lpts pifib hardware police
flow ospf unicast default rate 200
flow bgp configured rate 200
flow bgp default rate 100

Note

The show lpts pifib hardware police location 0/RP0/CPU0 command displays pre-Internal Forwarding Information Base (IFIB) information for the designated node.

Configuration Example

Configure the LPTS policer for the OSPF and BGP flow types with the following values:

  • ospf unicast default rate 100

  • bgp configured rate 300 

Router#configure
Router(config)#lpts pifib hardware police
Router(config-pifib-policer-per-node)#flow ospf unicast default rate 200
Router(config-pifib-policer-per-node)#flow bgp configured rate 200
Router(config-pifib-policer-per-node)#flow bgp default rate 100
Router(config-pifib-policer-per-node)#commit

Running Configuration

lpts pifib hardware police location 0/RP0/CPU0
flow ospf unicast default rate 100
flow bgp configured rate 300

Verification

Router#show run lpts pifib hardware police                
lpts pifib hardware police
flow ospf unicast default rate 100
flow bgp configured rate 300
!

Verification

The show controllers npu stats traps-all instance all location 0/0/CPU0 command displays packets that are locally processed and packets that are dropped by the CPU. 

Router# show controllers npu stats traps-all instance all location 0/0/CPU0 

Trap Type                                     NPU  Trap TrapStats   Policer Packet    Packet
                                              ID    ID      ID              Accepted  Dropped
==============================================================================================
RxTrapMimSaMove(CFM_DOWM_MEP_DMM)             0    6    0x6         32037   0         0         
RxTrapMimSaUnknown(RCY_CFM_DOWN_MEP_DMM)      0    7    0x7         32037   0         0         
RxTrapAuthSaLookupFail (IPMC default)         0    8    0x8         32033   0         0         
RxTrapSaMulticast                             0    11   0xb         32018   0         0         
RxTrapArpMyIp                                 0    13   0xd         32001   0         0         
RxTrapArp                                     0    14   0xe         32001   11        0         
RxTrapDhcpv4Server                            0    18   0x12        32022   0         0         
RxTrapDhcpv4Client                            0    19   0x13        32022   0         0         
RxTrapDhcpv6Server                            0    20   0x14        32022   0         0         
RxTrapDhcpv6Client                            0    21   0x15        32022   0         0         
RxTrapL2Cache_LACP                            0    23   0x17        32003   0         0         
RxTrapL2Cache_LLDP1                           0    24   0x18        32004   0         0         
RxTrapL2Cache_LLDP2                           0    25   0x19        32004   1205548   0         
RxTrapL2Cache_LLDP3                           0    26   0x1a        32004   0         0         
RxTrapL2Cache_ELMI                            0    27   0x1b        32005   0         0         
RxTrapL2Cache_BPDU                            0    28   0x1c        32027   0         0         
RxTrapL2Cache_BUNDLE_BPDU                     0    29   0x1d        32027   0         0         
RxTrapL2Cache_CDP                             0    30   0x1e        32002   0         0         
RxTrapHeaderSizeErr                           0    32   0x20        32018   0         0         
RxTrapIpCompMcInvalidIp                       0    35   0x23        32018   0         0         
RxTrapMyMacAndIpDisabled                      0    36   0x24        32018   0         0         
RxTrapMyMacAndMplsDisable                     0    37   0x25        32018   0         0         
RxTrapArpReply                                0    38   0x26        32001   2693      0         
RxTrapFibDrop                                 0    41   0x29        32018   0         0         
RxTrapMTU                                     0    42   0x2a        32020   0         0         
RxTrapMiscDrop                                0    43   0x2b        32018   0         0         
RxTrapL2AclDeny                               0    44   0x2c        32034   0         0         
Rx_UNKNOWN_PACKET                             0    46   0x2e        32018   0         0         
RxTrapL3AclDeny                               0    47   0x2f        32034   0         0         
RxTrapOamY1731MplsTp(OAM_SWOFF_DN_CCM)        0    57   0x39        32029   0         0         
RxTrapOamY1731Pwe(OAM_SWOFF_DN_CCM)           0    58   0x3a        32030   0         0         
RxTrapOamLevel                                0    64   0x40        32023   0         0         
RxTrapRedirectToCpuOamPacket                  0    65   0x41        32025   0         0         
RxTrapOamPassive                              0    66   0x42        32024   0         0         
RxTrap1588                                    0    67   0x43        32038   0         0         
RxTrapExternalLookupError                     0    72   0x48        32018   0         0         
RxTrapArplookupFail                           0    73   0x49        32001   0         0         
RxTrapUcLooseRpfFail                          0    84   0x54        32035   0         0         
RxTrapMplsControlWordTrap                     0    88   0x58        32015   0         0         
RxTrapMplsControlWordDrop                     0    89   0x59        32015   0         0         
RxTrapMplsUnknownLabel                        0    90   0x5a        32018   0         0         
RxTrapIpv4VersionError                        0    98   0x62        32018   0         0         
RxTrapIpv4ChecksumError                       0    99   0x63        32018   0         0         
RxTrapIpv4HeaderLengthError                   0    100  0x64        32018   0         0         
RxTrapIpv4TotalLengthError                    0    101  0x65        32018   0         0         
RxTrapIpv4Ttl0                                0    102  0x66        32008   0         0         
RxTrapIpv4Ttl1                                0    104  0x68        32008   0         0         
RxTrapIpv4DipZero                             0    106  0x6a        32018   0         0         
RxTrapIpv4SipIsMc                             0    107  0x6b        32018   0         0         
RxTrapIpv6VersionError                        0    109  0x6d        32018   0         0         
RxTrapIpv6HopCount0                           0    110  0x6e        32011   0         0         
RxTrapIpv6LoopbackAddress                     0    113  0x71        32018   0         0         
RxTrapIpv6MulticastSource                     0    114  0x72        32018   0         0         
RxTrapIpv6NextHeaderNull                      0    115  0x73        32010   0         0         
RxTrapIpv6Ipv4CompatibleDestination           0    121  0x79        32018   0         0         
RxTrapMplsTtl1                                0    125  0x7d        32012   316278    2249      
RxTrapUcStrictRpfFail                         0    137  0x89        32035   0         0         
RxTrapMcExplicitRpfFail                       0    138  0x8a        32033   0         0         
RxTrapOamp(OAM_BDL_DN_NON_CCM)                0    141  0x8d        32031   0         0         
RxTrapOamEthUpAccelerated(OAM_BDL_UP_NON_CCM) 0    145  0x91        32032   0         0         
RxTrapReceive                                 0    150  0x96        32017   125266112 0         
RxTrapUserDefine_FIB_IPV4_NULL0               0    151  0x97        32018   0         0         
RxTrapUserDefine_FIB_IPV6_NULL0               0    152  0x98        32018   0         0         
RxTrapUserDefine_FIB_IPV4_GLEAN               0    153  0x99        32016   0         0         
RxTrapUserDefine_FIB_IPV6_GLEAN               0    154  0x9a        32016   0         0         
RxTrapUserDefine_IPV4_OPTIONS                 0    155  0x9b        32006   0         0         
RxTrapUserDefine_IPV4_RSVP_OPTIONS            0    156  0x9c        32007   0         0         
RxTrapUserDefine                              0    157  0x9d        32026   0         0         
RxTrapUserDefine_BFD                          0    163  0xa3        32028   0         0         
RxTrapMC                                      0    181  0xb5        32033   0         0         
RxNetflowSnoopTrap0                           0    182  0xb6        32018   0         0         
RxNetflowSnoopTrap1                           0    183  0xb7        32018   0         0         
RxTrapMimSaMove(CFM_DOWM_MEP_DMM)             1    6    0x6         32037   0         0         
RxTrapMimSaUnknown(RCY_CFM_DOWN_MEP_DMM)      1    7    0x7         32037   0         0         
RxTrapAuthSaLookupFail (IPMC default)         1    8    0x8         32033   0         0         
RxTrapSaMulticast                             1    11   0xb         32018   0         0         
RxTrapArpMyIp                                 1    13   0xd         32001   0         0

Understanding ACL-based Policers

ACL-based LPTS policers are session-based policers that provide secure network access for each session.

Benefits

These are the benefits of ACL-based policer:

  • Provides rate limit on incoming packets based on session.

  • Modifies policer rates depending on traffic load.

  • Blocks entire traffic based on a specific session without impacting other sessions with the same flow.

Restrictions

  • It is recommended to have up to 10 prefixes in a single ACL. The ACEs in an ACL should be managed such that there is no overlap of prefixes.

  • Up to 50 ACL-based LPTS policers can be configured on a router.

  • ACL-based LPTS policers can be configured to an IPv4 LPTS session that has a particular flow type and that matches the default VRF.

  • ACL-based LPTS policers can be configured to an IPv4 or IPv6 LPTS session that has a particular flow type and that matches the VRF ID.

Configure IPv4 ACL-based LPTS Policers

This section describes how you can configure IPv4 ACL-based LPTS policers.

Configuration Example

To configure ACL-based LPTS policers for IPv4 sessions, complete the following configurations:

  1. Configure an ACL.

  2. Configure LPTS policer for a particular IPv4 session matching an ACL and VRF.

Configuration


/* Enter the global configuration mode and configure an ACL */
Router# configure
Router(config)# ipv4 access-list ACL1_OSPF
Router(config-ipv4-acl)# 10 permit ipv4 host 192.168.1.5 any
Router(config-ipv4-acl)# commit
Router(config-ipv4-acl)# exit

/* Configure LPTS policer for a particular IPv4 session matching an ACL and VRF. */
Router(config)# lpts pifib hardware police
Router(config-pifib-policer-global)# acl ACL1_OSPF rate 2000 vrf red8
Router(config-if)# commit

Verification

Use the following command to display the ACL-based LPTS policer entries attached to matching entries: 

Router#show lpts pifib hardward entry statistics location 0/RP0/CPU0
Offset  NPU   L3   VRF id  L4  Intf Dest Pkts/Drops laddr,Port     raddr,Port  acl name
-----  -----  ---  -----  ---  ---  -----  -------  --------        --------   -----
  37   0 [0] IPV4   *    any  any   Local  0/0     any,any           any,any
  38   0 [1] IPV4   *    any  any   Local  0/0     any,any           any,any
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
 187   0 [0] IPV4   *    ICMP any   Local  0/0     any,8             any,ECHO   ACL3_ICMP
 188   0 [1] IPV4   *    ICMP any   Local  0/0     any,8             any,ECHO   ACL3_ICMP
 189   0 [2] IPV4   *    ICMP any   Local  0/0     any,8             any,ECHO   ACL3_ICMP
 190   0 [3] IPV4   *    ICMP any   Local  0/0     any,8             any,ECHO   ACL3_ICMP
8963   0 [0] IPV4 default UDP OptV2 Local  22588/0 192.168.10.2,646  any,any    ACL4_UDP
8964   0 [1] IPV4 default UDP OptV2 Local  22590/0 192.168.10.2,646  any,any    ACL4_UDP
8965   0 [2] IPV4 default UDP OptV2 Local  0/0     192.168.10.2,646  any,any    ACL4_UDP
8966   0 [3] IPV4 default UDP OptV2 Local  0/0     192.168.10.2,646  any,any    ACL4_UDP
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
8279   0 [0] IPV4 default OSPF OptV2 Local 846248/0 192.168.10.5,any any,any    ACL1_OSPF
8280   0 [1] IPV4 default OSPF OptV2 Local 962717/0 192.168.10.5,any any,any    ACL1_OSPF
8281   0 [3] IPV4 default OSPF OptV2 Local 421169/0 192.168.10.5,any any,any    ACL1_OSPF
8281   0 [4] IPV4 default OSPF OptV2 Local 0/0      192.168.10.5,any any,any    ACL1_OSPF
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
8339   0 [0] IPV4 red8    OSPF OptV2 Local  0/0     192.168.10.5,any any,any    ACL1_OSPF
8340   0 [1] IPV4 red8    OSPF OptV2 Local  0/0     192.168.10.5,any any,any    ACL1_OSPF
8341   0 [2] IPV4 red8    OSPF OptV2 Local  11099/0 192.168.10.5,any any,any    ACL1_OSPF
8342   0 [1] IPV4 red8    OSPF OptV2 Local  0/0     192.168.10.5,any any,any    ACL1_OSPF
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
8363   0 [0] IPV4  red7   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8364   0 [1] IPV4  red7   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8365   0 [2] IPV4  red7   OSPF OptV2 Local  11099/0 192.168.10.5,any any,any    ACL1_OSPF
8366   0 [3] IPV4  red7   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
8375   0 [0] IPV4  red6   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8376   0 [1] IPV4  red6   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8377   0 [2] IPV4  red6   OSPF OptV2 Local  11103/0 192.168.10.5,any any,any    ACL1_OSPF
8378   0 [3] IPV4  red6   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
8391   0 [0] IPV4  red5   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8392   0 [1] IPV4  red5   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8393   0 [2] IPV4  red5   OSPF OptV2 Local  11104/0 192.168.10.5,any any,any    ACL1_OSPF
8394   0 [3] IPV4  red5   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
8411   0 [0] IPV4  red4   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8412   0 [1] IPV4  red4   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8413   0 [2] IPV4  red4   OSPF OptV2 Local  11101/0 192.168.10.5,any any,any    ACL1_OSPF
8414   0 [3] IPV4  red4   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
8427   0 [0] IPV4  red3   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8428   0 [1] IPV4  red3   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8429   0 [2] IPV4  red3   OSPF OptV2 Local  11107/0 192.168.10.5,any any,any    ACL1_OSPF
8430   0 [3] IPV4  red3   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
8439   0 [0] IPV4  red1   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8440   0 [1] IPV4  red1   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
8441   0 [2] IPV4  red1   OSPF OptV2 Local  11099/0 192.168.10.5,any any,any    ACL1_OSPF
8442   0 [3] IPV4  red1   OSPF OptV2 Local   0/0    192.168.10.5,any any,any    ACL1_OSPF
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
  .      .     .    .     .    .     .       .         .                .
8276   0 [1] IPV4 default OSPF OptV2 Local  1752/0  any,any         any,any

Configure IPv6 ACL-based LPTS Policers

This section describes how you can configure IPv6 ACL-based LPTS policers.

Configuration Example

To configure ACL-based LPTS policers for IPv6 sessions, complete the following configurations:

  1. Configure a VRF.

  2. Configure an ACL.

  3. Configure LPTS policer for a particular IPv6 session matching an ACL and VRF ID.

Configuration


/* Enter the global configuration mode and configure an VRF */
Router# configure
Router(config)# vrf red83
Router(config)# commit

/* Configure an ACL */
Router(config)# ipv6 access-list ACL33
Router(config-ipv6-acl)# 10 permit ipv6 host 4000:21::1 host 4000:21::2
Router(config-ipv6-acl)# 60 permit ipv6 host 4000:53::1 host 4000:53::2
Router(config-ipv6-acl)# commit
Router(config-ipv6-acl)# exit

/* Configure LPTS policer for a particular IPv6 session matching an ACL and VRF ID. */
Router(config)# lpts pifib hardware police
Router(config-pifib-policer-global)# acl ACL33 rate 5000 vrf red83 ipv6
Router(config-pifib-policer-global)# commit

Verification

Use the following command to display the ACL-based LPTS policer entries attached to matching entries: 

Router#show lpts pifib hardward entry statistics location 0/RP0/CPU0

Offset  NPU   L3   VRF id  L4   Intf Dest Pkts/Drops  laddr,Port    raddr,Port    acl name
-----  -----  ---  -----  ---  ---  -----  -------    --------      --------      -----
1498   0 [0] IPV6  red83  TCP  any  Local  383/0  4000:53::1,179  4000:53::1,179   ACL33
1499   0 [1] IPV6  red83  TCP  any  Local  0/0    4000:53::1,179  4000:53::2,43329 ACL33
1450   0 [2] IPV6  red83  TCP  any  Local  0/0    4000:53::1,179  4000:53::2,43329 ACL33
1451   0 [3] IPV6  red83  TCP  any  Local  0/0    4000:53::1,179  4000:53::2,43329 ACL33