Configure Segment Routing for IS-IS Protocol

Integrated Intermediate System-to-Intermediate System (IS-IS), Internet Protocol Version 4 (IPv4), is a standards-based Interior Gateway Protocol (IGP). The Cisco IOS XR software implements the IP routing capabilities described in International Organization for Standardization (ISO)/International Engineering Consortium (IEC) 10589 and RFC 1995, and adds the standard extensions for single topology and multitopology IS-IS for IP Version 6 (IPv6).

This module provides the configuration information used to enable segment routing for IS-IS.


Note


For additional information on implementing IS-IS on your Cisco NCS 5000 Series Router, see the Implementing IS-IS module in the Routing Configuration Guide for Cisco NCS 5000 Series Routers.


Enabling Segment Routing for IS-IS Protocol

Segment routing on the IS-IS control plane supports the following:

  • IPv4 control plane

  • Level 1, level 2, and multi-level routing

  • Prefix SIDs for host prefixes on loopback interfaces

  • Adjacency SIDs for adjacencies

  • MPLS penultimate hop popping (PHP) and explicit-null signaling

This task explains how to enable segment routing for IS-IS.

Before you begin

Your network must support the MPLS Cisco IOS XR software feature before you enable segment routing for IS-IS on your router.


Note


You must enter the commands in the following task list on every IS-IS router in the traffic-engineered portion of your network.


SUMMARY STEPS

  1. configure
  2. router isis instance-id
  3. address-family ipv4 [ unicast ]
  4. metric-style wide [ level { 1 | 2 }]
  5. segment-routing mpls [sr-prefer]
  6. exit
  7. Use the commit or end command.

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Example:


RP/0/RP0/CPU0:router# configure

Enters mode.

Step 2

router isis instance-id

Example:


RP/0/RP0/CPU0:router(config)# router isis isp

Enables IS-IS routing for the specified routing instance, and places the router in router configuration mode.

Note

 
You can change the level of routing to be performed by a particular routing instance by using the is-type router configuration command.

Step 3

address-family ipv4 [ unicast ]

Example:


RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast

Specifies the IPv4 address family, and enters router address family configuration mode.

Step 4

metric-style wide [ level { 1 | 2 }]

Example:


RP/0/RP0/CPU0:router(config-isis-af)# metric-style wide level 1

Configures a router to generate and accept only wide link metrics in the Level 1 area.

Step 5

segment-routing mpls [sr-prefer]

Example:


RP/0/RP0/CPU0:router(config-isis-af)# segment-routing mpls

Segment routing is enabled by the following actions:

  • MPLS forwarding is enabled on all interfaces where IS-IS is active.

  • All known prefix-SIDs in the forwarding plain are programmed, with the prefix-SIDs advertised by remote routers or learned through local or remote mapping server.

  • The prefix-SIDs locally configured are advertised.

Use the sr-prefer keyword to set the preference of segment routing (SR) labels over label distribution protocol (LDP) labels.

Step 6

exit

Example:


RP/0/RP0/CPU0:router(config-isis-af)# exit
RP/0/RP0/CPU0:router(config-isis)# exit

Step 7

Use the commit or end command.

commit —Saves the configuration changes and remains within the configuration session.

end —Prompts user to take one of these actions:
  • Yes — Saves configuration changes and exits the configuration session.

  • No —Exits the configuration session without committing the configuration changes.

  • Cancel —Remains in the configuration session, without committing the configuration changes.

What to do next

Configure the prefix SID.

Configuring a Prefix-SID on the IS-IS Enabled Loopback Interface

A prefix segment identifier (SID) is associated with an IP prefix. The prefix SID is manually configured from the segment routing global block (SRGB) range of labels. A prefix SID is configured under the loopback interface with the loopback address of the node as the prefix. The prefix segment steers the traffic along the shortest path to its destination.

A prefix SID can be a node SID or an Anycast SID. A node SID is a type of prefix SID that identifies a specific node. An Anycast SID is a type of prefix SID that identifies a set of nodes, and is configured with n-flag clear. The set of nodes (Anycast group) is configured to advertise a shared prefix address and prefix SID. Anycast routing enables the steering of traffic toward multiple advertising nodes. Packets addressed to an Anycast address are forwarded to the topologically nearest nodes.

The prefix SID is globally unique within the segment routing domain.

This task explains how to configure prefix segment identifier (SID) index or absolute value on the IS-IS enabled Loopback interface.

Before you begin

Ensure that segment routing is enabled on the corresponding address family.

SUMMARY STEPS

  1. configure
  2. router isis instance-id
  3. interface Loopback instance
  4. address-family ipv4 [ unicast ]
  5. Use the commit or end command.

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Example:


RP/0/RP0/CPU0:router# configure

Enters mode.

Step 2

router isis instance-id

Example:


RP/0/RP0/CPU0:router(config)# router isis 1

Enables IS-IS routing for the specified routing instance, and places the router in router configuration mode.

  • You can change the level of routing to be performed by a particular routing instance by using the is-type router configuration command.

Step 3

interface Loopback instance

Example:


RP/0/RP0/CPU0:router(config-isis)# interface Loopback0

Specifies the loopback interface and instance.

Step 4

address-family ipv4 [ unicast ]

Example:

The following is an example for ipv4 address family:

RP/0/RP0/CPU0:router(config-isis-if)# address-family ipv4 unicast

Specifies the IPv4 address family, and enters router address family configuration mode.

Step 5

Use the commit or end command.

commit —Saves the configuration changes and remains within the configuration session.

end —Prompts user to take one of these actions:
  • Yes — Saves configuration changes and exits the configuration session.

  • No —Exits the configuration session without committing the configuration changes.

  • Cancel —Remains in the configuration session, without committing the configuration changes.

Verify the prefix-SID configuration:

RP/0/RP0/CPU0:router# show isis database verbose 

IS-IS 1 (Level-2) Link State Database
LSPID                 LSP Seq Num  LSP Checksum  LSP Holdtime  ATT/P/OL
router.00-00        * 0x0000039b   0xfc27        1079            0/0/0
  Area Address: 49.0001
  NLPID:        0xcc
  NLPID:        0x8e
  MT:           Standard (IPv4 Unicast)
  Hostname:     router
  IP Address:   10.0.0.1
  Router Cap:   10.0.0.1, D:0, S:0
    Segment Routing: I:1 V:1, SRGB Base: 16000 Range: 8000
<...>
  Metric: 0          IP-Extended 10.0.0.1/32
    Prefix-SID Index: 1001, Algorithm:0, R:0 N:1 P:0 E:0 V:0 L:0
<...>

 

IS-IS Prefix Attributes for Extended IPv4 and IPv6 Reachability

The following sub-TLVs support the advertisement of IPv4 and IPv6 prefix attribute flags and the source router ID of the router that originated a prefix advertisement, as described in RFC 7794.

  • Prefix Attribute Flags

  • IPv4 and IPv6 Source Router ID

Prefix Attribute Flags

The Prefix Attribute Flag sub-TLV supports the advertisement of attribute flags associated with prefix advertisements. Knowing if an advertised prefix is directly connected to the advertising router helps to determine how labels that are associated with an incoming packet should be processed.

This section describes the behavior of each flag when a prefix advertisement is learned from one level to another.


Note


Prefix attributes are only added when wide metric is used.

Prefix Attribute Flags Sub-TLV Format


   0 1 2 3 4 5 6 7 ...
  +-+-+-+-+-+-+-+-+...
  |X|R|N|          ...
  +-+-+-+-+-+-+-+-+...

Prefix Attribute Flags Sub-TLV Fields

Field

Description

X (External Prefix Flag)

This flag is set if the prefix has been redistributed from another protocol. The value of the flag is preserved when the prefix is propagated to another level.

R (Re-advertisement Flag)

This flag is set to 1 by the Level 1-2 router when the prefix is propagated between IS-IS levels (from Level 1 to Level 2, or from Level 2 to Level 1).

This flag is set to 0 when the prefix is connected locally to an IS-IS-enabled interface (regardless of the level configured on the interface).

N (Node Flag)

For prefixes that are propagated from another level:

  1. Copy the N-flag from the prefix attribute sub-TLV, if present in the source level.

  2. Copy the N-flag from the prefix-SID sub-TLV, if present in the source level.

  3. Otherwise, set to 0.

For connected prefixes:

  1. Set to 0 if prefix-attributes n-flag-clear is configured (see Configuring Prefix Attribute N-flag-clear).

  2. Set to 0 if n-flag-clear{ n-flag-clearSID-index | n-flag-clearSID-value} n-flag-clear is configured (see Configuring a Prefix-SID on the IS-IS Enabled Loopback Interface).

  3. Otherwise, set to 1 when the prefix is a host prefix (/32 for IPV4, /128 for IPv6) that is associated with a loopback address.

    Note

     
    If the flag is set and the prefix length is not a host prefix, then the flag must be ignored.

IPv4 and IPv6 Source Router ID

The Source Router ID sub-TLV identifies the source of the prefix advertisement. The IPv4 and IPv6 source router ID is displayed in the output of the show isis database verbose command.

The Source Router ID sub-TLV is added when the following conditions are met:

  1. The prefix is locally connected.

  2. The N-flag is set to 1 (when it's a host prefix and the n-flag-clear configuration is not used).

  3. The router ID is configured in the corresponding address family.

The source router ID is propagated between levels.

Table 1. Source Router Sub-TLV Format

IPv4 Source Router ID

Type: 11

Length: 4

Value: IPv4 Router ID of the source of the prefix advertisement

IPv6 Source Router ID

Type: 12

Length: 16

Value: IPv6 Router ID of the source of the prefix advertisement

Configuring Prefix Attribute N-flag-clear

The N-flag is set to 1 when the prefix is a host prefix (/32 for IPV4, /128 for IPv6) that is associated with a loopback address. The advertising router can be configured to not set this flag. This task explains how to clear the N-flag.

SUMMARY STEPS

  1. configure
  2. router isis instance-id
  3. interface Loopback instance
  4. prefix-attributes n-flag-clear[ Level-1| Level-2]
  5. Use the commit or end command.

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Example:


RP/0/RP0/CPU0:router# configure

Enters mode.

Step 2

router isis instance-id

Example:


RP/0/RP0/CPU0:router(config)# router isis 1

Step 3

interface Loopback instance

Example:


RP/0/RP0/CPU0:router(config)# interface Loopback0

Specifies the loopback interface.

Step 4

prefix-attributes n-flag-clear[ Level-1| Level-2]

Example:


RP/0/RP0/CPU0:router(config-if)# isis prefix-attributes n-flag-clear

Clears the prefix attribute N-flag explicitly.

Step 5

Use the commit or end command.

commit —Saves the configuration changes and remains within the configuration session.

end —Prompts user to take one of these actions:
  • Yes — Saves configuration changes and exits the configuration session.

  • No —Exits the configuration session without committing the configuration changes.

  • Cancel —Remains in the configuration session, without committing the configuration changes.

Verify the prefix attribute configuration:

RP/0/RP0/CPU0:router# show isis database verbose 

IS-IS 1 (Level-2) Link State Database
LSPID                 LSP Seq Num  LSP Checksum  LSP Holdtime  ATT/P/OL
router.00-00        * 0x0000039b   0xfc27        1079            0/0/0
  Area Address: 49.0001
  NLPID:        0xcc
  NLPID:        0x8e
  MT:           Standard (IPv4 Unicast)
  MT:           IPv6 Unicast                                     0/0/0
  Hostname:     router
  IP Address:   10.0.0.1
  IPv6 Address: 2001:0db8:1234::0a00:0001
  Router Cap:   10.0.0.1, D:0, S:0
    Segment Routing: I:1 V:1, SRGB Base: 16000 Range: 8000
    SR Algorithm: 
      Algorithm: 0
      Algorithm: 1
<...>
  Metric: 0          IP-Extended 10.0.0.1/32
    Prefix-SID Index: 1001, Algorithm:0, R:1 N:0 P:1 E:0 V:0 L:0
    Prefix Attribute Flags: X:0 R:1 N:0
  Metric: 10         IP-Extended 10.0.0.2/32
    Prefix-SID Index: 1002, Algorithm:0, R:0 N:1 P:0 E:0 V:0 L:0
    Prefix Attribute Flags: X:0 R:0 N:1
    Source Router ID: 10.0.0.2
<...>

 

IS-IS Multi-Domain Prefix SID and Domain Stitching: Example

IS-IS Multi-Domain Prefix SID and Domain Stitching allows you to configure multiple IS-IS instances on the same loopback interface for domain border nodes. You specify a loopback interface and prefix SID under multiple IS-IS instances to make the prefix and prefix SID reachable in different domains.

This example uses the following topology. Node 5 and 9 are border nodes between two IS-IS domains (Domain1 and Domain2). Node 10 is configured as the Segment Routing Path Computation Element (SR-PCE).

Figure 1. Multi-Domain Topology

Configure IS-IS Multi-Domain Prefix SID

Specify a loopback interface and prefix SID under multiple IS-IS instances on each border node:


Example: Border Node 5
router isis Domain1
 interface Loopback0
  address-family ipv4 unicast
   prefix-sid absolute 16005

router isis Domain2
 interface Loopback0
  address-family ipv4 unicast
   prefix-sid absolute 16005


Example: Border Node 9
router isis Domain1
 interface Loopback0
  address-family ipv4 unicast
   prefix-sid absolute 16009

router isis Domain2
 interface Loopback0
  address-family ipv4 unicast
   prefix-sid absolute 16009

Border nodes 5 and 9 each run two IS-IS instances (Domain1 and Domain2) and advertise their Loopback0 prefix and prefix SID in both domains.

Nodes in both domains can reach the border nodes by using the same prefix and prefix SID. For example, Node 3 and Node 22 can reach Node 5 using prefix SID 16005.

Configure Common Router ID

On each border node, configure a common TE router ID under each IS-IS instance:


Example: Border Node 5
router isis Domain1
 address-family ipv4 unicast
  router-id loopback0

router isis Domain2
 address-family ipv4 unicast
  router-id loopback0 


Example: Border Node 9
router isis Domain1
 address-family ipv4 unicast
  router-id loopback0 

router isis Domain2
 address-family ipv4 unicast
  router-id loopback0 

Distribute IS-IS Link-State Data

Configure BGP Link-state (BGP-LS) on Node 13 and Node 14 to report their local domain to Node 10:


Example: Node 13
router isis Domain1
 distribute link-state instance-id instance-id 


Example: Node 14
router isis Domain2
 distribute link-state instance-id instance-id 

Link-state ID starts from 32. One ID is required per IGP domain. Different domain IDs are essential to identify that the SR-TE TED belongs to a particular IGP domain.

Nodes 13 and 14 each reports its local domain in BGP-LS to Node 10.

Node 10 identifies the border nodes (Nodes 5 and 9) by their common advertised TE router ID, then combines (stitches) the domains on these border nodes for end-to-end path computations.