Implementing Routing Policy

A routing policy instructs the router to inspect routes, filter them, and potentially modify their attributes as they are accepted from a peer, advertised to a peer, or redistributed from one routing protocol to another.

This module describes how routing protocols make decisions to advertise, aggregate, discard, distribute, export, hold, import, redistribute and modify the routes based on configured routing policy.

The routing policy language (RPL) provides a single, straightforward language in which all routing policy needs can be expressed. RPL was designed to support large-scale routing configurations. It greatly reduces the redundancy inherent in previous routing policy configuration methods. RPL streamlines the routing policy configuration, reduces system resources required to store and process these configurations, and simplifies troubleshooting.

Restrictions for Implementing Routing Policy

These restrictions apply when working with Routing Policy Language implementation:
  • Border Gateway Protocol (BGP), integrated Intermediate System-to-Intermediate System (IS-IS), or Open Shortest Path First (OSPF) must be configured in your network.

  • An individual policy definition of up to 1000 statements are supported. The total number of statements within a policy can be extended to 4000 statements using hierarchical policy constructs. However, this limit is restricted with the use of apply statements.

  • When a policy that is attached directly or indirectly to an attach point needs to be modified, a single commit operation cannot be performed when:
    • Removing a set or policy referred by another policy that is attached to any attach point directly or indirectly.

    • Modifying the policy to remove the reference to the same set or policy that is getting removed.

    The commit must be performed in two steps:
    1. Modify the policy to remove the reference to the policy or set and then commit .

    2. Remove the policy or set and commit .

  • Per-vrf label mode is not supported for Carrier Supporting Carrier (CSC) network with internal and external BGP multipath setup.

  • You cannot change the next hop address to an IPv6 address through RPL policy for a route that starts from an IPv4 peer.

Define Route Policy

This task explains how to define a route policy.


Note


  • If you want to modify an existing routing policy using the command-line interface (CLI), you must redefine the policy by completing this task.

  • Modifying the RPL scale configuration may take a long time.

  • BGP may crash either due to large scale RPL configuration changes, or during consecutive RPL changes. To avoid BGP crash, wait until there are no messages in the BGP In/Out queue before committing further changes.



Tip


You can programmatically configure the route policy using openconfig-routing-policy.yang OpenConfig data model. To get started with using data models, see the Programmability Configuration Guide for Cisco NCS 560 Series Routers.


Procedure


Step 1

configure

Example:


RP/0/RP0/CPU0:router# configure

Enters mode.

Step 2

route-policy name [ parameter1 , parameter2 , . . . , parameterN ]

Example:


RP/0/RP0/CPU0:router(config)# route-policy sample1

Enters route-policy configuration mode.

  • After the route-policy has been entered, a group of commands can be entered to define the route-policy.

Step 3

end-policy

Example:


RP/0/RP0/CPU0:router(config-rpl)# end-policy

Ends the definition of a route policy and exits route-policy configuration mode.

Step 4

Use the commit or end command.

commit —Saves the configuration changes and remains within the configuration session.

end —Prompts user to take one of these actions:
  • Yes — Saves configuration changes and exits the configuration session.

  • No —Exits the configuration session without committing the configuration changes.

  • Cancel —Remains in the configuration session, without committing the configuration changes.


Routing Policy Definition: Example

In the following example, a BGP route policy named sample1 is defined using the route-policy name command. The policy compares the network layer reachability information (NLRI) to the elements in the prefix set test. If it evaluates to true, the policy performs the operations in the then clause. If it evaluates to false, the policy performs the operations in the else clause, that is, sets the MED value to 200 and adds the community 2:100 to the route. The final steps of the example commit the configuration to the router, exit configuration mode, and display the contents of route policy sample1.


configure
 route-policy sample1
  if destination in test then
   drop
  else
   set med 200
   set community (2:100) additive
  endif
 end-policy
 end
show config running route-policy sample1
Building configuration...
 route-policy sample1
  if destination in test then
   drop
  else
   set med 200
   set community (2:100) additive
  endif
 end-policy

Attach Routing Policy to BGP Neighbor

This task explains how to attach a routing policy to a BGP neighbor.

Before you begin

A routing policy must be preconfigured and well defined prior to it being applied at an attach point. If a policy is not predefined, an error message is generated stating that the policy is not defined.

Procedure


Step 1

configure

Example:


RP/0/RP0/CPU0:router# configure

Enters mode.

Step 2

router bgp as-number

Example:


RP/0/RP0/CPU0:router(config)# router bgp 125

Configures a BGP routing process and enters router configuration mode.

  • The as-number argument identifies the autonomous system in which the router resides. Valid values are from 0 to 65535. Private autonomous system numbers that can be used in internal networks range from 64512 to 65535.

Step 3

neighbor ip-address

Example:


RP/0/RP0/CPU0:router(config-bgp)# neighbor 10.0.0.20

Specifies a neighbor IP address.

Step 4

address-family { ipv4 unicast | | ipv6 unicast | } address-family { ipv4 | ipv6 } unicast

Example:


RP/0/RP0/CPU0:router(config-bgp-nbr)# address-family ipv4 unicast

Specifies the address family.

Step 5

route-policy policy-name { in | out }

Example:


RP/0/RP0/CPU0:router(config-bgp-nbr-af)# route-policy example1 in

Attaches the route-policy, which must be well formed and predefined.

Step 6

Use the commit or end command.

commit —Saves the configuration changes and remains within the configuration session.

end —Prompts user to take one of these actions:
  • Yes — Saves configuration changes and exits the configuration session.

  • No —Exits the configuration session without committing the configuration changes.

  • Cancel —Remains in the configuration session, without committing the configuration changes.


Modify Routing Policy Using Text Editor

This task explains how to modify an existing routing policy using a text editor.

Procedure


Step 1

edit { route-policy | prefix-set | as-path-set | community-set | extcommunity-set { rt | soo } | policy-global | rd-set } name [ nano | emacs | vim | inline { add | prepend | remove } set-element ]

Example:


RP/0/RP0/CPU0:router# edit route-policy sample1

Identifies the route policy, prefix set, AS path set, community set, or extended community set name to be modified.

  • A copy of the route policy, prefix set, AS path set, community set, or extended community set is copied to a temporary file and the editor is launched.

  • After editing with Nano, save the editor buffer and exit the editor by using the Ctrl-X keystroke.

  • After editing with Emacs, save the editor buffer by using the Ctrl-X and Ctrl-S keystrokes. To save and exit the editor, use the Ctrl-X and Ctrl-C keystrokes.

  • After editing with Vim, to write to a current file and exit, use the :wq or :x or ZZ keystrokes. To quit and confirm, use the :q keystrokes. To quit and discard changes, use the :q! keystrokes.

Step 2

show rpl route-policy [ name [ detail ] | states | brief ]

Example:


RP/0/RP0/CPU0:router# show rpl route-policy sample2

(Optional) Displays the configuration of a specific named route policy.

  • Use the detail keyword to display all policies and sets that a policy uses.

  • Use the states keyword to display all unused, inactive, and active states.

  • Use the brief keyword to list the names of all extended community sets without their configurations.

Step 3

show rpl prefix-set [ name | states | brief ]

Example:


RP/0/RP0/CPU0:router# show rpl prefix-set prefixset1

(Optional) Displays the contents of a named prefix set.

  • To display the contents of a named AS path set, community set, or extended community set, replace the prefix-set keyword with as-path-set , community-set , or extcommunity-set , respectively.


Simple Inbound Policy: Example

The following policy discards any route whose network layer reachability information (NLRI) specifies a prefix longer than /24, and any route whose NLRI specifies a destination in the address space reserved by RFC 1918. For all remaining routes, it sets the MED and local preference, and adds a community to the list in the route.

For routes whose community lists include any values in the range from 101:202 to 106:202 that have a 16-bit tag portion containing the value 202, the policy prepends autonomous system number 2 twice, and adds the community 2:666 to the list in the route. Of these routes, if the MED is either 666 or 225, then the policy sets the origin of the route to incomplete, and otherwise sets the origin to IGP.

For routes whose community lists do not include any of the values in the range from 101:202 to 106:202, the policy adds the community 2:999 to the list in the route.


prefix-set too-specific
 0.0.0.0/0 ge 25 le 32
end-set

prefix-set rfc1918
 10.0.0.0/8 le 32,
 172.16.0.0/12 le 32,
 192.168.0.0/16 le 32
end-set

route-policy inbound-tx
 if destination in too-specific or destination in rfc1918 then
  drop
 endif
 set med 1000
 set local-preference 90
 set community (2:1001) additive
 if community matches-any ([101..106]:202) then
  prepend as-path 2.30 2
  set community (2:666) additive
 if med is 666 or med is 225 then
  set origin incomplete
 else
  set origin igp
 endif
else
  set community (2:999) additive
 endif
 end-policy

 router bgp 2
  neighbor 10.0.1.2 address-family ipv4 unicast route-policy inbound-tx in

The following policy example shows how to build two inbound policies, in-100 and in-101, for two different peers. In building the specific policies for those peers, the policy reuses some common blocks of policy that may be common to multiple peers. It builds a few basic building blocks, the policies common-inbound, filter-bogons, and set-lpref-prepend.

The filter-bogons building block is a simple policy that filters all undesirable routes, such as those from the RFC 1918 address space. The policy set-lpref-prepend is a utility policy that can set the local preference and prepend the AS path according to parameterized values that are passed in. The common-inbound policy uses these filter-bogons building blocks to build a common block of inbound policy. The common-inbound policy is used as a building block in the construction of in-100 and in-101 along with the set-lpref-prepend building block.


  prefix-set bogon
    10.0.0.0/8 ge 8 le 32,
    0.0.0.0,
    0.0.0.0/0 ge 27 le 32,
    192.168.0.0/16 ge 16 le 32
  end-set
  !
  route-policy in-100
    apply common-inbound
    if community matches-any ([100..120]:135) then
      apply set-lpref-prepend (100,100,2)
      set community (2:1234) additive
    else
      set local-preference 110
    endif
    if community matches-any ([100..666]:[100..999]) then
      set med 444
      set local-preference 200
      set community (no-export) additive
    endif
  end-policy
  !
  route-policy in-101
    apply common-inbound
    if community matches-any ([101..200]:201) then
      apply set-lpref-prepend(100,101,2)
      set community (2:1234) additive
    else
      set local-preference 125
    endif
  end-policy
  !
  route-policy filter-bogons
    if destination in bogon then
  drop
  else 
  pass
    endif
  end-policy
  !
  route-policy common-inbound
    apply filter-bogons
    set origin igp
    set community (2:333)
  end-policy
  !
  route-policy set-lpref-prepend($lpref,$as,$prependcnt)
    set local-preference $lpref
    prepend as-path $as $prependcnt
  end-policy
  

References for Routing Policy

To implement RPL, you need to understand the following concepts:

Routing Policy Language

This section contains the following information:

Routing Policy Language Overview

RPL was developed to support large-scale routing configurations. RPL has several fundamental capabilities that differ from those present in configurations oriented to traditional route maps, access lists, and prefix lists. The first of these capabilities is the ability to build policies in a modular form. Common blocks of policy can be defined and maintained independently. These common blocks of policy can then be applied from other blocks of policy to build complete policies. This capability reduces the amount of configuration information that needs to be maintained. In addition, these common blocks of policy can be parameterized. This parameterization allows for policies that share the same structure but differ in the specific values that are set or matched against to be maintained as independent blocks of policy. For example, three policies that are identical in every way except for the local preference value they set can be represented as one common parameterized policy that takes the varying local preference value as a parameter to the policy.

The policy language introduces the notion of sets. Sets are containers of similar data that can be used in route attribute matching and setting operations. Four set types exist: prefix-sets, community-sets, as-path-sets, and extcommunity-sets. These sets hold groupings of IPv4 or IPv6 prefixes, community values, AS path regular expressions, and extended community values, respectively. Sets are simply containers of data. Most sets also have an inline variant. An inline set allows for small enumerations of values to be used directly in a policy rather than having to refer to a named set. Prefix lists, community lists, and AS path lists must be maintained even when only one or two items are in the list. An inline set in RPL allows the user to place small sets of values directly in the policy body without having to refer to a named set.

Decision making, such as accept and deny, is explicitly controlled by the policy definitions themselves. RPL combines matching operators, which may use set data, with the traditional Boolean logic operators AND, OR, and NOT into complex conditional expressions. All matching operations return a true or false result. The execution of these conditional expressions and their associated actions can then be controlled by using simple if then, elseif, and else structures, which allow the evaluation paths through the policy to be fully specified by the user.

Routing Policy Language Structure

This section describes the basic structure of RPL.

Names

The policy language provides two kinds of persistent, namable objects: sets and policies. Definition of these objects is bracketed by beginning and ending command lines. For example, to define a policy named test, the configuration syntax would look similar to the following:


  route-policy test
  [ . . . policy statements . . . ]
  end-policy
  
  

Legal names for policy objects can be any sequence of the upper- and lowercase alphabetic characters; the numerals 0 to 9; and the punctuation characters period, hyphen, and underscore. A name must begin with a letter or numeral.

Sets

In this context, the term set is used in its mathematical sense to mean an unordered collection of unique elements. The policy language provides sets as a container for groups of values for matching purposes. Sets are used in conditional expressions. The elements of the set are separated by commas. Null (empty) sets are allowed.

In the following example:


  prefix-set backup-routes 
    # currently no backup routes are defined 
  end-set
  
  

a condition such as:


  if destination in backup-routes then 
  
  

evaluates as FALSE for every route, because there is no match-condition in the prefix set that it satisfies.

You may want to perform comparisons against a small number of elements, such as two or three community values, for example. To allow for these comparisons, the user can enumerate these values directly. These enumerations are referred to as inline sets. Functionally, inline sets are equivalent to named sets, but allow for simple tests to be inline. Thus, comparisons do not require that a separate named set be maintained when only one or two elements are being compared. See the set types described in the following sections for the syntax. In general, the syntax for an inline set is a comma-separated list surrounded by parentheses, where element-entry is an entry of an item appropriate to the type of usage such as a prefix or a community value.

The following is an example using an inline community set:


  route-policy sample-inline
  if community matches-any ([10..15]:100) then
  set local-preference 100
  endif
  end-policy
  
  

The following is an equivalent example using the named set test-communities:


  community-set test-communities
  10:100,
  11:100,
  12:100,
  13:100,
  14:100,
  15:100
  end-set
  
  route-policy sample
  if community matches-any test-communities then
  set local-preference 100
  endif
  end-policy
  
  

Both of these policies are functionally equivalent, but the inline form does not require the configuration of the community set just to store the six values. You can choose the form appropriate to the configuration context. In the following sections, examples of both the named set version and the inline form are provided where appropriate.

as-path-set

An AS path set comprises operations for matching an AS path attribute. The only matching operation is a regular expression match.

Named Set Form

The named set form uses the ios-regex keyword to indicate the type of regular expression and requires single quotation marks around the regular expression.

The following is a sample definition of a named AS path set:


  as-path-set aset1
  ios-regex ’_42$’,
  ios-regex ’_127$’
  end-set
  
  

This AS path set comprises two elements. When used in a matching operation, this AS path set matches any route whose AS path ends with either the autonomous system (AS) number 42 or 127.

To remove the named AS path set, use the no as-path-set aset1 command-line interface (CLI) command.


Note


Regular expression matching is CPU intensive. The policy performance can be substantially improved by either collapsing the regular expression patterns together to reduce the total number of regular expression invocations or by using equivalent native as-path match operations such as ‘as-path neighbor-is’, ‘as-path originates-from’ or ‘as-path passes-through’.


Inline Set Form

The inline set form is a parenthesized list of comma-separated expressions, as follows:


  (ios-regex '_42$', ios-regex '_127$')
  
  

This set matches the same AS paths as the previously named set, but does not require the extra effort of creating a named set separate from the policy that uses it.

community-set

A community-set holds community values for matching against the BGP community attribute. A community is a 32-bit quantity. Integer community values must be split in half and expressed as two unsigned decimal integers in the range from 0 to 65535, separated by a colon. Single 32-bit community values are not allowed. The following is the named set form:

Named Set Form

  community-set cset1
  12:34,
  12:56,
  12:78,
  internet
  end-set
  
Inline Set Form

  (12:34, 12:56, 12:78)
  ($as:34, $as:$tag1, 12:78, internet)
  
  

The inline form of a community-set also supports parameterization. Each 16-bit portion of the community may be parameterized.

RPL provides symbolic names for the standard well-known community values: internet is 0:0, no-export is 65535:65281, no-advertise is 65535:65282, and local-as is 65535:65283.

RPL also provides a facility for using wildcards in community specifications. A wildcard is specified by inserting an asterisk (*) in place of one of the 16-bit portions of the community specification; the wildcard indicates that any value for that portion of the community matches. Thus, the following policy matches all communities in which the autonomous system part of the community is 123:


  community-set cset3
     123:*
  end-set
  
  

Every community set must contain at least one community value. Empty community sets are invalid and are rejected.

extcommunity-set

An extended community-set is analogous to a community-set except that it contains extended community values instead of regular community values. It also supports named forms and inline forms. There are three types of extended community sets: cost, soo, and rt.

As with community sets, the inline form supports parameterization within parameterized policies. Either portion of the extended community value can be parameterized.

Wildcards (*) and regular expressions are allowed for extended community set elements.

Every extended community-set must contain at least one extended community value. Empty extended community-sets are invalid and rejected.

The following are syntactic examples:

Named Form for Extcommunity-set RT
An rt set is an extcommunity set used to store BGP Route Target (RT) extended community type communities:

  extcommunity-set rt a_rt_set
     1.2.3.4:666
     1234:666,
     1.2.3.4:777,
     4567:777
  end-set
  
  Inline Set Form for Extcommunity-set RT
  
  (1.2.3.4:666, 1234:666, 1.2.3.4:777, 4567:777)
  ($ipadrr:666, 1234:$tag, 1.2.3.4:777, $tag2:777)
  
These options are supported under extended community set RT:

RP/0/RP0/CPU0:router(config)#extcommunity-set rt rt_set
RP/0/RP0/CPU0:router(config-ext)#?
  #-remark        Remark beginning with '#'
  *               Wildcard (any community or part thereof)
  <1-4294967295>  32-bit decimal number
  <1-65535>       16-bit decimal number
  A.B.C.D/M:N     Extended community - IPv4 prefix format
  A.B.C.D:N       Extended community - IPv4 format
  ASN:N           Extended community - ASPLAIN format
  X.Y:N           Extended community - ASDOT format
  abort           Discard RPL definition and return to top level config
  dfa-regex       DFA style regular expression
  end-set         End of set definition
  exit            Exit from this submode
  ios-regex       Traditional IOS style regular expression
  show            Show partial RPL configuration

Option Description
#-remark Remark beginning with '#'
* Wildcard (any community or part thereof)
<1-4294967295> 32-bit decimal number
<1-65535> 16-bit decimal number
A.B.C.D/M:N Extended community - IPv4 prefix format
A.B.C.D:N Extended community - IPv4 format
ASN:N Extended community - ASPLAIN format
X.Y:N Extended community - ASDOT format
abort Discard RPL definition and return to top level config
dfa-regex DFA style regular expression
end-set End of set definition
exit Exit from this submode
ios-regex Traditional IOS style regular expression
show Show partial RPL configuration
Named Form for Extcommunity-set Soo
A soo set is an extcommunity set used to store BGP Site-of-Origin (SoO) extended community type communities:

  extcommunity-set soo a_soo_set
1.1.1:100,
     100:200
  end-set
  
These options are supported under extended community set Soo:

RP/0/RP0/CPU0:router(config)#extcommunity-set soo soo_set
RP/0/RP0/CPU0:router(config-ext)#?
  #-remark        Remark beginning with '#'
  *               Wildcard (any community or part thereof)
  <1-4294967295>  32-bit decimal number
  <1-65535>       16-bit decimal number
  A.B.C.D/M:N     Extended community - IPv4 prefix format
  A.B.C.D:N       Extended community - IPv4 format
  ASN:N           Extended community - ASPLAIN format
  X.Y:N           Extended community - ASDOT format
  abort           Discard RPL definition and return to top level config
  dfa-regex       DFA style regular expression
  end-set         End of set definition
  exit            Exit from this submode
  ios-regex       Traditional IOS style regular expression
  show            Show partial RPL configuration

Option Description
#-remark Remark beginning with '#'
* Wildcard (any community or part thereof)
<1-4294967295> 32-bit decimal number
<1-65535> 16-bit decimal number
A.B.C.D/M:N Extended community - IPv4 prefix format
A.B.C.D:N Extended community - IPv4 format
ASN:N Extended community - ASPLAIN format
X.Y:N Extended community - ASDOT format
abort Discard RPL definition and return to top level config
dfa-regex DFA style regular expression
end-set End of set definition
exit Exit from this submode
ios-regex Traditional IOS style regular expression
show Show partial RPL configuration
prefix-set

A prefix-set holds IPv4 or IPv6 prefix match specifications, each of which has four parts: an address, a mask length, a minimum matching length, and a maximum matching length. The address is required, but the other three parts are optional. The address is a standard dotted-decimal IPv4 or colon-separated hexadecimal IPv6 address. The mask length, if present, is a nonnegative decimal integer in the range from 0 to 32 (0 to 128 for IPv6) following the address and separated from it by a slash. The optional minimum matching length follows the address and optional mask length and is expressed as the keyword ge (mnemonic for greater than or equal to), followed by a nonnegative decimal integer in the range from 0 to 32 (0 to 128 for IPv6). The optional maximum matching length follows the rest and is expressed by the keyword le (mnemonic for less than or equal to), followed by yet another nonnegative decimal integer in the range from 0 to 32 (0 to 128 for IPv6). A syntactic shortcut for specifying an exact length for prefixes to match is the eq keyword (mnemonic for equal to).

If a prefix match specification has no mask length, then the default mask length is 32 for IPv4 and 128 for IPv6. The default minimum matching length is the mask length. If a minimum matching length is specified, then the default maximum matching length is 32 for IPv4 and 128 for IPv6. Otherwise, if neither minimum nor maximum is specified, the default maximum is the mask length.

The prefix-set itself is a comma-separated list of prefix match specifications. The following are examples:


  prefix-set legal-ipv4-prefix-examples
     10.0.1.1,
     10.0.2.0/24,
     10.0.3.0/24 ge 28,
     10.0.4.0/24 le 28,
     10.0.5.0/24 ge 26 le 30,
     10.0.6.0/24 eq 28,
     10.0.7.2/32 ge 16 le 24,
     10.0.8.0/26 ge 8 le 16
  end-set
  
  prefix-set legal-ipv6-prefix-examples
    2001:0:0:1::/64,
    2001:0:0:2::/64 ge 96,
    2001:0:0:2::/64 ge 96 le 100,
    2001:0:0:2::/64 eq 100
  end-set
  
  

The first element of the prefix-set matches only one possible value, 10.0.1.1/32 or the host address 10.0.1.1. The second element matches only one possible value, 10.0.2.0/24. The third element matches a range of prefix values, from 10.0.3.0/28 to 10.0.3.255/32. The fourth element matches a range of values, from 10.0.4.0/24 to 10.0.4.240/28. The fifth element matches prefixes in the range from 10.0.5.0/26 to 10.0.5.252/30. The sixth element matches any prefix of length 28 in the range from 10.0.6.0/28 through 10.0.6.240/28. The seventh element matches any prefix of length 32 in the range 10.0.[0..255].2/32 (from 10.0.0.2/32 to 10.0.255.2). The eighth element matches any prefix of length 26 in the range 10.[0..255].8.0/26 (from 10.0.8.0/26 to 10.255.8.0/26).

The following prefix-set consists entirely of invalid prefix match specifications:


  prefix-set ILLEGAL-PREFIX-EXAMPLES
     10.1.1.1 ge 16,
     10.1.2.1 le 16,
     10.1.3.0/24 le 23,
     10.1.4.0/24 ge 33,
     10.1.5.0/25 ge 29 le 28
  end-set
  
  

Neither the minimum length nor maximum length is valid without a mask length. For IPv4, the minimum length must be less than 32, the maximum length of an IPv4 prefix. For IPv6, the minimum length must be less than 128, the maximum length of an IPv6 prefix. The maximum length must be equal to or greater than the minimum length.

ACL Support in RPL Prefix Sets

Access Control List (ACL) type prefix set entries holds IPv4 or IPv6 prefix match specifications, each of which has an address and a wildcard mask. The address and wildcard mask is a standard dotted-decimal IPv4 or colon-separated hexadecimal IPv6 address. The set of bits to be matched are provided in the form of wildcard also called as inverted mask in which a binary 0 means a mandatory match and binary 1 means a do not match condition. The prefix set allows to specify contiguous and non-contiguous set of bits that should be matched in any route.

rd-set

An rd-set is used to create a set with route distinguisher (RD) elements. An RD set is a 64-bit value prepended to an IPv4 address to create a globally unique Border Gateway Protocol (BGP) VPN IPv4 address.

You can define RD values with the following commands:

  • a.b.c.d:m:*—BGP VPN RD in IPv4 format with a wildcard character. For example, 10.0.0.2:255.255.0.0:*.

  • a.b.c.d/m:n—BGP VPN RD in IPv4 format with a mask. For example, 10.0.0.2:255.255.0.0:666.

  • a.b.c.d:** —BGP VPN RD in IPv4 format with a wildcard character. For example, 10.0.0.2:255.255.0.0.

  • a.b.c.d:n— BGP VPN RD in IPv4 format. For example, 10.0.0.2:666.

  • asn:*— BGP VPN RD in ASN format with a wildcard character. For example, 10002:255.255.0.0.

  • asn:n—BGP VPN RD in ASN format. For example, 10002:666.

The following is an example of an rd-set:


  rd-set rdset1
     10.0.0.0/8:*,
     10.0.0.0/8:777,
     10.0.0.0:*,
     10.0.0.0:777,
     65000:*,
     65000:777
  end-set
  
  

Routing Policy Language Components

Four main components in the routing policy language are involved in defining, modifying, and using policies: the configuration front end, policy repository, execution engine, and policy clients themselves.

The configuration front end (CLI) is the mechanism to define and modify policies. This configuration is then stored on the router using the normal storage means and can be displayed using the normal configuration show commands.

The second component of the policy infrastructure, the policy repository, has several responsibilities. First, it compiles the user-entered configuration into a form that the execution engine can understand. Second, it performs much of the verification of policies; and it ensures that defined policies can actually be executed properly. Third, it tracks which attach points are using which policies so that when policies are modified the appropriate clients are properly updated with the new policies relevant to them.

The third component is the execution engine. This component is the piece that actually runs policies as the clients request. The process can be thought of as receiving a route from one of the policy clients and then executing the actual policy against the specific route data.

The fourth component is the policy clients (the routing protocols). This component calls the execution engine at the appropriate times to have a given policy be applied to a given route, and then perform some number of actions. These actions may include deleting the route if policy indicated that it should be dropped, passing along the route to the protocol decision tree as a candidate for the best route, or advertising a policy modified route to a neighbor or peer as appropriate.

Routing Policy Language Usage

This section provides basic routing policy language usage examples.

Pass PolicyPass Policy

The following example shows how the policy accepts all presented routes without modifying the routes.


  route-policy quickstart-pass
  pass
  end-policy
  
Drop Everything Policy

The following example shows how the policy explicitly rejects all routes presented to it. This type of policy is used to ignore everything coming from a specific peer.


  route-policy quickstart-drop
  drop
  end-policy
  
Ignore Routes with Specific AS Numbers in the Path

The following example shows the policy definition in three parts. First, the as-path-set command defines three regular expressions to match against an AS path. Second, the route-policy command applies the AS path set to a route. If the AS path attribute of the route matches the regular expression defined with the as-path-set command, the protocol refuses the route. Third, the route policy is attached to BGP neighbor 10.0.1.2. BGP consults the policy named ignore_path_as on routes received (imported) from neighbor 10.0.1.2.


  as-path-set ignore_path
  ios-regex '_11_',
  ios-regex '_22_',
  ios-regex '_33_'
  end-set
  
  route-policy ignore_path_as
  if as-path in ignore_path then
  drop
  else
  pass
  endif
  end-policy
  
  router bgp 2
  neighbor 10.0.1.2 address-family ipv4 unicast policy ignore_path_as in
  
Set Community Based on MED

The following example shows how the policy tests the MED of a route and modifies the community attribute of the route based on the value of the MED. If the MED value is 127, the policy adds the community 123:456 to the route. If the MED value is 63, the policy adds the value 123:789 to the community attribute of the route. Otherwise, the policy removes the community 123:123 from the route. In any case, the policy instructs the protocol to accept the route.


  route-policy quickstart-med
  if med eq 127 then
  set community (123:456) additive
  elseif med eq 63 then
  set community (123:789) additive
  else
  delete community in (123:123)
  endif
  pass
  end-policy
  
Set Local Preference Based on Community

The following example shows how the community-set named quickstart-communities defines community values. The route policy named quickstart-localpref tests a route for the presence of the communities specified in the quickstart-communities community set. If any of the community values are present in the route, the route policy sets the local preference attribute of the route to 31. In any case, the policy instructs the protocol to accept the route.


  community-set quickstart-communities
  987:654,
  987:543,
  987:321,
  987:210
  end-set
  
  route-policy quickstart-localpref
  if community matches-any quickstart-communities then
  set local-preference 31
  endif
  pass
  end-policy
  
Persistent Remarks

The following example shows how comments are placed in the policy to clarify the meaning of the entries in the set and the statements in the policy. The remarks are persistent, meaning they remain attached to the policy. For example, remarks are displayed in the output of the show running-config command. Adding remarks to the policy makes the policy easier to understand, modify at a later date, and troubleshoot if an unexpected behavior occurs.


  prefix-set rfc1918
  # These are the networks defined as private in RFC1918 (including
  # all subnets thereof)
  10.0.0.0/8 ge 8,
  172.16.0.0/12 ge 12,
  192.168.0.0/16 ge 16
  end-set
  
  route-policy quickstart-remarks
  # Handle routes to RFC1918 networks
  if destination in rfc1918 then
  # Set the community such that we do not export the route
  set community (no-export) additive
  
  endif
  end-policy
  

Policy Definitions

Policy definitions create named sequences of policy statements. A policy definition consists of the CLI route-policy keyword followed by a name, a sequence of policy statements, and the end-policy keyword. For example, the following policy drops any route it encounters:


  route-policy drop-everything
  drop
  end-policy
  
  

The name serves as a handle for binding the policy to protocols. To remove a policy definition, issue the no route-policy name command.

Policies may also refer to other policies such that common blocks of policy can be reused. This reference to other policies is accomplished by using the apply statement, as shown in the following example:


  route-policy check-as-1234
  if as-path passes-through ‘1234.5’ then
  apply drop-everything
  else
  pass
  endif
  end-policy
  
  

The apply statement indicates that the policy drop-everything should be executed if the route under consideration passed through autonomous system 1234.5 before it is received. If a route that has autonomous system 1234.5 in its AS path is received, the route is dropped; otherwise, the route is accepted without modification. This policy is an example of a hierarchical policy. Thus, the semantics of the apply statement are just as if the applied policy were cut and pasted into the applying policy:


  route-policy check-as-1234-prime
   if as-path passes-through '1234.5' then
      drop
   else
      pass
   endif
  end-policy
  
  

You may have as many levels of hierarchy as desired. However, many levels may be difficult to maintain and understand.

Parameterization

In addition to supporting reuse of policies using the apply statement, policies can be defined that allow for parameterization of some of the attributes. The following example shows how to define a parameterized policy named param-example. In this case, the policy takes one parameter, $mytag. Parameters always begin with a dollar sign and consist otherwise of any alphanumeric characters. Parameters can be substituted into any attribute that takes a parameter.

In the following example, a 16-bit community tag is used as a parameter:


  route-policy param-example ($mytag)
  set community (1234:$mytag) additive
  end-policy
  
  

This parameterized policy can then be reused with different parameterization, as shown in the following example. In this manner, policies that share a common structure but use different values in some of their individual statements can be modularized. For details on which attributes can be parameterized, see the individual attribute sections.


  route-policy origin-10
  if as-path originates-from ‘10.5’ then
  apply param-example(10.5)
  else
  pass
  endif
  end-policy
  
  route-policy origin-20
  if as-path originates-from ‘20.5’ then
  apply param-example(20.5)
  else
  pass
  endif
  end-policy
  
  

The parameterized policy param-example provides a policy definition that is expanded with the values provided as the parameters in the apply statement. Note that the policy hierarchy is always maintained, Thus, if the definition of param-example changes, then the behavior of origin_10 and origin_20 changes to match.

The effect of the origin-10 policy is that it adds the community 1234:10 to all routes that pass through this policy and have an AS path indicating the route originated from autonomous system 10. The origin-20 policy is similar except that it adds to community 1234:20 for routes originating from autonomous system 20.

Parameterization at Attach Points

In addition to supporting parameterization using the apply statement, policies can also be defined that allow for parameterization the attributes at attach points. Parameterization is supported at all attach points.

In the following example, we define a parameterized policy "param-example". In this example, the policy takes two parameters "$mymed" and “$prefixset”. Parameters always begin with a dollar sign, and consist otherwise of any alphanumeric characters. Parameters can be substituted into any attribute that takes a parameter. In this example we are passing a MED value and prefix set name as parameters.


  route-policy param-example ($mymed, $prefixset)
    if destination in $prefixset then
    set med $mymed
    endif
  end-policy
  
  

This parameterized policy can then be reused with different parameterizations as shown in the example below. In this manner, policies that share a common structure but use different values in some of their individual statements can be modularized. For details on which attributes can be parameterized, see the individual attributes for each protocol.


  router bgp 2
    neighbor 10.1.1.1
      remote-as 3
      address-family ipv4 unicast
        route-policy param-example(10, prefix_set1)
        route-policy param-example(20, prefix_set2)
  
  

The parameterized policy param-example provides a policy definition that is expanded with the values provided as the parameters in the neighbor route-policy in and out statement.

Global Parameterization

RPL supports the definition of systemwide global parameters that can be used inside policy definition. Global parameters can be configured as follows:


  Policy-global
    glbpathtype ‘ebgp’
    glbtag ‘100’
  end-global
  
  

The global parameter values can be used directly inside a policy definition similar to the local parameters of parameterized policy. In the following example, the globalparam argument, which makes use of the global parameters gbpathtype and glbtag, is defined for a nonparameterized policy.


  route-policy globalparam
    if path-type is $glbpathtype then
      set tag $glbtag
    endif
  end-policy
  
  

When a parameterized policy has a parameter name “collision” with a global parameter name, parameters local to policy definition take precedence, effectively masking off global parameters. In addition, a validation mechanism is in place to prevent the deletion of a particular global parameter if it is referred by any policy.

Semantics of Policy Application

This section discusses how routing policies are evaluated and applied. The following concepts are discussed:

Boolean Operator Precedence

Boolean expressions are evaluated in order of operator precedence, from left to right. The highest precedence operator is NOT, followed by AND, and then OR. The following expression:


  med eq 10 and not destination in (10.1.3.0/24) or community matches-any ([10..25]:35) 
  
  

if fully parenthesized to display the order of evaluation, would look like this:


  (med eq 10 and (not destination in (10.1.3.0/24))) or community matches-any ([10..25]:35)
  
  

The inner NOT applies only to the destination test; the AND combines the result of the NOT expression with the Multi Exit Discriminator (MED) test; and the OR combines that result with the community test. If the order of operations are rearranged:


  not med eq 10 and destination in (10.1.3.0/24) or community matches-any ([10..25]:35)
  
  

then the expression, fully parenthesized, would look like the following:

((not med eq 10) and destination in (10.1.3.0/24)) or community matches-any ([10..25]:35)

Multiple Modifications of Same Attribute

When a policy replaces the value of an attribute multiple times, the last assignment wins because all actions are executed. Because the MED attribute in BGP is one unique value, the last value to which it gets set to wins. Therefore, the following policy results in a route with a MED value of 12:


  set med 9
  set med 10
  set med 11
  set med 12
  
  

This example is trivial, but the feature is not. It is possible to write a policy that effectively changes the value for an attribute. For example:


  set med 8
  if community matches-any cs1 then
  set local-preference 122
  if community matches-any cs2 then
  set med 12
  endif
  endif
  
  

The result is a route with a MED of 8, unless the community list of the route matches both cs1 and cs2, in which case the result is a route with a MED of 12.

In the case in which the attribute being modified can contain only one value, it is easy to think of this case as the last statement wins. However, a few attributes can contain multiple values and the result of multiple actions on the attribute is cumulative rather than as a replacement. The first of these cases is the use of the additive keyword on community and extended community evaluation. Consider a policy of the form:


  route-policy community-add
  set community (10:23)
  set community (10:24) additive
  set community (10:25) additive
  end-policy
  
  

This policy sets the community string on the route to contain all three community values: 10:23, 10:24, and 10:25.

The second of these cases is AS path prepending. Consider a policy of the form:


  route-policy prepend-example
  prepend as-path 2.5 3
  prepend as-path 666.5 2
  end-policy
  
  

This policy prepends 666.5 666.5 2.5 2.5 2.5 to the AS path. This prepending is a result of all actions being taken and to the AS path being an attribute that contains an array of values rather than a simple scalar value.

When Attributes Are Modified

A policy does not modify route attribute values until all tests have been completed. In other words, comparison operators always run on the initial data in the route. Intermediate modifications of the route attributes do not have a cascading effect on the evaluation of the policy. Take the following example:


  ifmed eq 12 then
  set med 42
  if med eq 42 then
  drop
  endif
  endif
  
  

This policy never executes the drop statement because the second test (med eq 42) sees the original, unmodified value of the MED in the route. Because the MED has to be 12 to get to the second test, the second test always returns false.

Default Drop Disposition

All route policies have a default action to drop the route under evaluation unless the route has been modified by a policy action or explicitly passed. Applied (nested) policies implement this disposition as though the applied policy were pasted into the point where it is applied.

Consider a policy to allow all routes in the 10 network and set their local preference to 200 while dropping all other routes. You might write the policy as follows:


  route-policy two
  if destination in (10.0.0.0/8 ge 8 le 32) then
  set local-preference 200
  endif
  end-policy
  
  route-policy one
  apply two
  end-policy
  
  

It may appear that policy one drops all routes because it neither contains an explicit pass statement nor modifies a route attribute. However, the applied policy does set an attribute for some routes and this disposition is passed along to policy one. The result is that policy one passes routes with destinations in network 10, and drops all others.

Control Flow

Policy statements are processed sequentially in the order in which they appear in the configuration. Policies that hierarchically reference other policy blocks are processed as if the referenced policy blocks had been directly substituted inline. For example, if the following policies are defined:


  route-policy one
  set weight 100
  end-policy
  
  route-policy two
  set med 200
  end-policy
  
  route-policy three
  apply two
  set community (2:666) additive
  end-policy
  
  route-policy four
  apply one
  apply three
  pass
  end-policy
  
  

Policy four could be rewritten in an equivalent way as follows:


  route-policy four-equivalent
  set weight 100
  set med 200
  set community (2:666) additive
  pass
  end-policy
  

Note


The pass statement is not required and can be removed to represent the equivalent policy in another way.


Policy Verification

Several different types of verification occur when policies are being defined and used.

Range Checking

As policies are being defined, some simple verifications, such as range checking of values, is done. For example, the MED that is being set is checked to verify that it is in a proper range for the MED attribute. However, this range checking cannot cover parameter specifications because they may not have defined values yet. These parameter specifications are verified when a policy is attached to an attach point. The policy repository also verifies that there are no recursive definitions of policy, and that parameter numbers are correct. At attach time, all policies must be well formed. All sets and policies that they reference must be defined and have valid values. Likewise, any parameter values must also be in the proper ranges.

Incomplete Policy and Set References

As long as a given policy is not attached at an attach point, the policy is allowed to refer to nonexistent sets and policies, which allows for freedom of workflow. You can build configurations that reference sets or policy blocks that are not yet defined, and then can later fill in those undefined policies and sets, thereby achieving much greater flexibility in policy definition. Every piece of policy you want to reference while defining a policy need not exist in the configuration. Thus, a user can define a policy sample that references the policy bar using an apply statement even if the policy bar does not exist. Similarly, a user can enter a policy statement that refers to a nonexistent set.

However, the existence of all referenced policies and sets is enforced when a policy is attached. If you attempt to attach the policy sample with the reference to an undefined policy bar at an inbound BGP policy using the neighbor 1.2.3.4 address-family ipv4 unicast policy sample in command, the configuration attempt is rejected because the policy bar does not exist.

Likewise, you cannot remove a route policy or set that is currently in use at an attach point because this removal would result in an undefined reference. An attempt to remove a route policy or set that is currently in use results in an error message to the user.

A condition exists that is referred to as a null policy in which the policy bar exists but has no statements, actions, or dispositions in it. In other words, the policy bar does exist as follows:


  route-policy bar
  end-policy
  
  

This is a valid policy block. It effectively forces all routes to be dropped because it is a policy block that never modifies a route, nor does it include the pass statement. Thus, the default action of drop for the policy block is followed.

Aggregation

The aggregation attach point generates an aggregate route to be advertised based on the conditional presence of subcomponents of that aggregate. Policies attached at this attach point are also able to set any of the valid BGP attributes on the aggregated routes. For example, the policy could set a community value or a MED on the aggregate that is generated. The specified aggregate is generated if any routes evaluated by the named policy pass the policy. More specifics of the aggregate are filtered using the suppress-route keyword. Any actions taken to set attributes in the route affect attributes on the aggregate.

In the policy language, the configuration is controlled by which routes pass the policy. The suppress map was used to selectively filter or suppress specific components of the aggregate when the summary-only flag is not set. In other words, when the aggregate and more specific components are being sent, some of the more specific components can be filtered using a suppress map. In the policy language, this is controlled by selecting the route and setting the suppress flag. The attribute-map allowed the user to set specific attributes on the aggregated route. In the policy language, setting attributes on the aggregated route is controlled by normal action operations.

In the following example, the aggregate address 10.0.0.0/8 is generated if there are any component routes in the range 10.0.0.0/8 ge 8 le 25 except for 10.2.0.0/24. Because summary-only is not set, all components of the aggregate are advertised. However, the specific component 10.1.0.0 are suppressed.


  route-policy sample
    if destination in (10.0.0.0/8 ge 8 le 25) then
      set community (10:33)
    endif
    if destination in (10.2.0.0/24) then
      drop
    endif
    if destination in (10.1.0.0/24) then
      suppress-route
    endif
  end-policy
  
  router bgp 2
  address-family ipv4
    aggregate-address 10.0.0.0/8 route-policy sample
    .
    .
    .
  

The effect of aggregation policy on the attributes of the aggregate is cumulative. Every time an aggregation policy matches a more specific route, the set operations in the policy may modify the aggregate. The aggregate in the following example has a MED value that varies according to the number of more specific routes that comprise the aggregate.


  route-policy bumping-aggregation
    set med +5
  end-policy
  
  

If there are three matching more specific routes, the MED of the aggregate is the default plus 15; if there are seventeen more specific routes, the MED of the aggregate is the default plus 85.

The order that the aggregation policy is applied to prefix paths is deterministic but unspecified. That is, a given set of routes always appears in the same order, but there is no way to predict the order.

A drop in aggregation policy does not prevent generation of an aggregate, but it does prevent the current more specific route from contributing to the aggregate. If another more specific route gives the route a pass, the aggregate is generated. Only one more specific pass is required to generate an aggregate.

Policy Statements

Four types of policy statements exist: remark, disposition (drop and pass), action (set), and if (comparator).

Remark

A remark is text attached to policy configuration but otherwise ignored by the policy language parser. Remarks are useful for documenting parts of a policy. The syntax for a remark is text that has each line prepended with a pound sign (#):


  # This is a simple one-line remark.
  
  # This
  # is a remark
  # comprising multiple
  # lines. 
  
  

In general, remarks are used between complete statements or elements of a set. Remarks are not supported in the middle of statements or within an inline set definition.

Unlike traditional !-comments in the CLI, RPL remarks persist through reboots and when configurations are saved to disk or a TFTP server and then loaded back onto the router.

Disposition

If a policy modifies a route, by default the policy accepts the route. RPL provides a statement to force the opposite—the drop statement. If a policy matches a route and executes a drop, the policy does not accept the route. If a policy does not modify the route, by default the route is dropped. To prevent the route from being dropped, the pass statement is used.

The drop statement indicates that the action to take is to discard the route. When a route is dropped, no further execution of policy occurs. For example, if after executing the first two statements of a policy the drop statement is encountered, the policy stops and the route is discarded.


Note


All policies have a default drop action at the end of execution.


The pass statement allows a policy to continue executing even though the route has not been modified. When a policy has finished executing, any route that has been modified in the policy or any route that has received a pass disposition in the policy, successfully passes the policy and completes the execution. If route policy B_rp is applied within route policy A_rp, execution continues from policy A_rp to policy B_rp and back to policy A_rp provided prefix is not dropped by policy B_rp.


  route-policy A_rp
    set community (10:10)
    apply B_rp
  end-policy
  !
  
  route-policy B_rp
    if destination in (121.23.0.0/16 le 32, 155.12.0.0/16 le 32) then 
    set community (121:155) additive 
    endif 
  end-policy 
  !
  

By default, a route is dropped at the end of policy processing unless either the policy modifies a route attribute or it passes the route by means of an explicit pass statement. For example, if route-policy B is applied within route-policy A, then execution continues from policy A to policy B and back to policy A, provided the prefix is not dropped by policy B.


  route-policy A
     if as-path neighbor-is '123' then
     apply B
     policy statement N
  end-policy
  
  

Whereas the following policies pass all routes that they evaluate.


  route-policy PASS-ALL
  pass
  end-policy
  
  
  route-policy SET-LPREF
  set local-preference 200
  end-policy
  
  

In addition to being implicitly dropped, a route may be dropped by an explicit drop statement. Drop statements cause a route to be dropped immediately so that no further policy processing is done. Note also that a drop statement overrides any previously processed pass statements or attribute modifications. For example, the following policy drops all routes. The first pass statement is executed, but is then immediately overridden by the drop statement. The second pass statement never gets executed.


  route-policy DROP-EXAMPLE
  pass
  drop
  pass
  end-policy
  
  

When one policy applies another, it is as if the applied policy were copied into the right place in the applying policy, and then the same drop-and-pass semantics are put into effect. For example, policies ONE and TWO are equivalent to policy ONE-PRIME:


  route-policy ONE
  apply two
  if as-path neighbor-is '123' then
  pass
  endif
  end-policy
    
  route-policy TWO
  if destination in (10.0.0.0/16 le 32) then
  drop
  endif
  end-policy
  
  route-policy ONE-PRIME
  if destination in (10.0.0.0/16 le 32) then
  drop
  endif    
  if as-path neighbor-is '123' then
  pass
  endif
  end-policy
  
  

Because the effect of an explicit drop statement is immediate, routes in 10.0.0.0/16 le 32 are dropped without any further policy processing. Other routes are then considered to see if they were advertised by autonomous system 123. If they were advertised, they are passed; otherwise, they are implicitly dropped at the end of all policy processing.

The done statement indicates that the action to take is to stop executing the policy and accept the route. When encountering a done statement, the route is passed and no further policy statements are executed. All modifications made to the route prior to the done statement are still valid.

Action

An action is a sequence of primitive operations that modify a route. Most actions, but not all, are distinguished by the set keyword. In a route policy, actions can be grouped together. For example, the following is a route policy comprising three actions:


  route-policy actions
  set med 217
  set community (12:34) additive
  delete community in (12:56)
  end-policy
  

If

In its simplest form, an if statement uses a conditional expression to decide which actions or dispositions should be taken for the given route. For example:


  if as-path in as-path-set-1 then 
  drop 
  endif
  
  

The example indicates that any routes whose AS path is in the set as-path-set-1 are dropped. The contents of the then clause may be an arbitrary sequence of policy statements.

The following example contains two action statements:


  if origin is igp then
  set med 42
  prepend as-path 73.5 5
  endif
  
  

The CLI provides support for the exit command as an alternative to the endif command.

The if statement also permits an else clause, which is executed if the if condition is false:


  if med eq 8 then
  set community (12:34) additive
  else
  set community (12:56) additive
  endif
  
  

The policy language also provides syntax, using the elseif keyword, to string together a sequence of tests:


  if med eq 150 then
  set local-preference 10
  elseif med eq 200 then
  set local-preference 60
  elseif med eq 250 then
  set local-preference 110
  else
  set local-preference 0
  endif
  
  

The statements within an if statement may themselves be if statements, as shown in the following example:


  if community matches-any (12:34,56:78) then
  if med eq 150 then
  drop
  endif
  set local-preference 100
  endif
  
  

This policy example sets the value of the local preference attribute to 100 on any route that has a community value of 12:34 or 56:78 associated with it. However, if any of these routes has a MED value of 150, then these routes with either the community value of 12:34 or 56:78 and a MED of 150 are dropped.

Boolean Conditions

In the previous section describing the if statement, all of the examples use simple Boolean conditions that evaluate to either true or false. RPL also provides a way to build compound conditions from simple conditions by means of Boolean operators.

Three Boolean operators exist: negation (not), conjunction (and), and disjunction (or). In the policy language, negation has the highest precedence, followed by conjunction, and then by disjunction. Parentheses may be used to group compound conditions to override precedence or to improve readability.

The following simple condition:


  med eq 42
  
  

is true only if the value of the MED in the route is 42, otherwise it is false.

A simple condition may also be negated using the not operator:


  not next-hop in (10.0.2.2)
  
  

Any Boolean condition enclosed in parentheses is itself a Boolean condition:


  (destination in prefix-list-1)
  
  

A compound condition takes either of two forms. It can be a simple expression followed by the and operator, itself followed by a simple condition:


  med eq 42 and next-hop in (10.0.2.2)
  
  

A compound condition may also be a simpler expression followed by the or operator and then another simple condition:


  origin is igp or origin is incomplete
  
  

An entire compound condition may be enclosed in parentheses:


  (med eq 42 and next-hop in (10.0.2.2))
  
  

The parentheses may serve to make the grouping of subconditions more readable, or they may force the evaluation of a subcondition as a unit.

In the following example, the highest-precedence not operator applies only to the destination test, the and operator combines the result of the not expression with the community test, and the or operator combines that result with the MED test.


  med eq 10 or not destination in (10.1.3.0/24) and community matches-any ([12..34]:[56..78])
  
  

With a set of parentheses to express the precedence, the result is the following:


  med eq 10 or ((not destination in (10.1.3.0/24)) and community matches-any ([12..34]:[56..78])
  
  

The following is another example of a complex expression:


  (origin is igp or origin is incomplete or not med eq 42) and next-hop in (10.0.2.2)
  
  

The left conjunction is a compound condition enclosed in parentheses. The first simple condition of the inner compound condition tests the value of the origin attribute; if it is Interior Gateway Protocol (IGP), then the inner compound condition is true. Otherwise, the evaluation moves on to test the value of the origin attribute again, and if it is incomplete, then the inner compound condition is true. Otherwise, the evaluation moves to check the next component condition, which is a negation of a simple condition.

apply

As discussed in the sections on policy definitions and parameterization of policies, the apply command executes another policy (either parameterized or unparameterized) from within another policy, which allows for the reuse of common blocks of policy. When combined with the ability to parameterize common blocks of policy, the apply command becomes a powerful tool for reducing repetitive configuration.

Attach Points

Policies do not become useful until they are applied to routes, and for policies to be applied to routes they need to be made known to routing protocols. In BGP, for example, there are several situations where policies can be used, the most common of these is defining import and export policy. The policy attach point is the point in which an association is formed between a specific protocol entity, in this case a BGP neighbor, and a specific named policy. It is important to note that a verification step happens at this point. Each time a policy is attached, the given policy and any policies it may apply are checked to ensure that the policy can be validly used at that attach point. For example, if a user defines a policy that sets the IS-IS level attribute and then attempts to attach this policy as an inbound BGP policy, the attempt would be rejected because BGP routes do not carry IS-IS attributes. Likewise, when policies are modified that are in use, the attempt to modify the policy is verified against all current uses of the policy to ensure that the modification is compatible with the current uses.

Each protocol has a distinct definition of the set of attributes (commands) that compose a route. For example, BGP routes may have a community attribute, which is undefined in OSPF. Routes in IS-IS have a level attribute, which is unknown to BGP. Routes carried internally in the RIB may have a tag attribute.

When a policy is attached to a protocol, the protocol checks the policy to ensure the policy operates using route attributes known to the protocol. If the protocol uses unknown attributes, then the protocol rejects the attachment. For example, OSPF rejects attachment of a policy that tests the values of BGP communities.

The situation is made more complex by the fact that each protocol has access to at least two distinct route types. In addition to native protocol routes, for example BGP or IS-IS, some protocol policy attach points operate on RIB routes, which is the common central representation. Using BGP as an example, the protocol provides an attach point to apply policy to routes redistributed from the RIB to BGP. An attach point dealing with two different kinds of routes permits a mix of operations: RIB attribute operations for matching and BGP attribute operations for setting.


Note


The protocol configuration rejects attempts to attach policies that perform unsupported operations.


The following sections describe the protocol attach points, including information on the attributes (commands) and operations that are valid for each attach point.

BGP Policy Attach Points

This section describes each of the BGP policy attach points and provides a summary of the BGP attributes and operators.

Additional-Path

The additional-path attach point provides increased control based on various attribute match operations. This attach point is used to decide whether a route-policy should be used to select additional-paths for a BGP speaker to be able to send multiple paths for the prefix.

The add path enables BGP prefix independent convergence (PIC) at the edge routers.

This example shows how to set a route-policy "add-path-policy" to be used for enabling selection of additional paths:
router bgp 100
 address-family ipv4 unicast
 additional-paths selection route-policy add-path-policy

Dampening

The dampening attach point controls the default route-dampening behavior within BGP. Unless overridden by a more specific policy on the associate peer, all routes in BGP apply the associated policy to set their dampening attributes.

The following policy sets dampening values for BGP IPv4 unicast routes. Those routes that are more specific than a /25 take longer to recover after they are dampened than the routes that are less specific than /25.


Note


When the dampening policy runs for a route, then the last "set dampening" statement that is encountered, takes effect.

  • If a "drop" statement is encountered, then the route is not dampened; even if the "set dampening" statement is encountered.

  • If a "pass" or "done" statement is encountered but not the "set dampening" statement, then the route is dampened using the default dampening parameters.

For example:

  • When policy1 applies another policy that is called policy2 and if a "pass" statement is encountered in policy2, then policy2 exits and continues to execute policy1.

  • If a "done" statement is encountered in policy2, then both policy1 and policy2 exits immediately.



  route-policy sample_damp
    if destination in (0.0.0.0/0 ge 25) then
      set dampening halflife 30 others default
    else
      set dampening halflife 20 others default
    endif
  end-policy
  
  router bgp 2
    address-family ipv4 unicast
      bgp dampening route-policy sample_damp
      .
      .
      .
  
Default Originate

The default originate attach point allows the default route (0.0.0.0/0) to be conditionally generated and advertised to a peer, based on the presence of other routes. It accomplishes this configuration by evaluating the associated policy against routes in the Routing Information Base (RIB). If any routes pass the policy, the default route is generated and sent to the relevant peer.

The following policy generates and sends a default-route to the BGP neighbor 10.0.0.1 if any routes that match 10.0.0.0/8 ge 8 le 32 are present in the RIB.


  route-policy sample-originate
    if rib-has-route in (10.0.0.0/8 ge 8 le 32) then
       pass
    endif
  end-policy
  
  router bgp 2
    neighbor 10.0.0.1
      remote-as 3
      address-family ipv4 unicast
      default-originate policy sample-originate
      .
      .
      .
  
Neighbor Export

The neighbor export attach point selects the BGP routes to send to a given peer or group of peers. The routes are selected by running the set of possible BGP routes through the associated policy. Any routes that pass the policy are then sent as updates to the peer or group of peers. The routes that are sent may have had their BGP attributes altered by the policy that has been applied.

The following policy sends all BGP routes to neighbor 10.0.0.5. Routes that are tagged with any community in the range 2:100 to 2:200 are sent with a MED of 100 and a community of 2:666. The rest of the routes are sent with a MED of 200 and a community of 2:200.


  route-policy sample-export
    if community matches-any (2:[100-200]) then
      set med 100
      set community (2:666)
    else
      set med 200
      set community (2:200)
    endif
  end-policy
  
  router bgp 2
    neighbor 10.0.0.5
      remote-as 3
    address-family ipv4 unicast
      route-policy sample-export out
      .
      .
      .
  
Neighbor Import

The neighbor import attach point controls the reception of routes from a specific peer. All routes that are received by a peer are run through the attached policy. Any routes that pass the attached policy are passed to the BGP Routing Information Base (BRIB) as possible candidates for selection as best path routes.

When a BGP import policy is modified, it is necessary to rerun all the routes that have been received from that peer against the new policy. The modified policy may now discard routes that were previously allowed through, allow through previously discarded routes, or change the way the routes are modified. A new configuration option in BGP (bgp auto-policy-soft-reset) that allows this modification to happen automatically in cases for which either soft reconfiguration is configured or the BGP route-refresh capability has been negotiated.

The following example shows how to receive routes from neighbor 10.0.0.1. Any routes received with the community 3:100 have their local preference set to 100 and their community tag set to 2:666. All other routes received from this peer have their local preference set to 200 and their community tag set to 2:200.


  route-policy sample_import
    if community matches-any (3:100) then
      set local-preference 100
      set community (2:666)
    else
      set local-preference 200
      set community (2:200)
    endif
  end-policy
  
  router bgp 2
    neighbor 10.0.0.1
      remote-as 3
      address-family ipv4 unicast
        route-policy sample_import in
        .
        .
        .
  
Network

The network attach point controls the injection of routes from the RIB into BGP. A route policy attached at this point is able to set any of the valid BGP attributes on the routes that are being injected.

The following example shows a route policy attached at the network attach point that sets the well-known community no-export for any routes more specific than /24:


  route-policy NetworkControl
    if destination in (0.0.0.0/0 ge 25) then
      set community (no-export) additive
    endif
  end-policy
  
  router bgp 2
    address-family ipv4 unicast
      network 172.16.0.5/27 route-policy NetworkControl
  
Redistribute

The redistribute attach point allows routes from other sources to be advertised by BGP. The policy attached at this point is able to set any of the valid BGP attributes on the routes that are being redistributed. Likewise, selection operators allow a user to control what route sources are being redistributed and which routes from those sources.

The following example shows how to redistribute all routes from OSPF instance 12 into BGP. If OSPF were carrying a default route, it is dropped. Routes carrying a tag of 10 have their local preference set to 300 and the community value of 2:666 and no-advertise attached. All other routes have their local preference set to 200 and a community value of 2:100 set.


  route-policy sample_redistribute
    if destination in (0.0.0.0/0) then
      drop
    endif
    if tag eq 10 then
       set local-preference 300
       set community (2:666, no-advertise)
    else
      set local-preference 200
      set community (2:100)
    endif
  end-policy
  
  router bgp 2
    address-family ipv4 unicast
      redistribute ospf 12 route-policy sample_redistribute
      .
      .
  
Show BGP

The show bgp attach point allows the user to display selected BGP routes that pass the given policy. Any routes that are not dropped by the attached policy are displayed in a manner similar to the output of the show bgp command.

In the following example, the show bgp route-policy command is used to display any BGP routes carrying a MED of 5:


  route-policy sample-display
    if med eq 5 then
      pass
    endif
  end-policy
  !
  show bgp route-policy sample-display
  
  

A show bgp policy route-policy command also exists, which runs all routes in the RIB past the named policy as if the RIB were an outbound BGP policy. This command then displays what each route looked like before it was modified and after it was modified, as shown in the following example:


  show rpl route-policy test2
  
  route-policy test2
    if (destination in  (10.0.0.0/8 ge 8 le 32)) then
      set med 333
    endif
  end-policy
  !

  show bgp
  
  BGP router identifier 10.0.0.1, local AS number 2
  BGP main routing table version 11
  BGP scan interval 60 secs
  Status codes:s suppressed, d damped, h history, * valid, > best
                i - internal, S stale
  Origin codes:i - IGP, e - EGP, ? - incomplete
     Network            Next Hop            Metric LocPrf Weight Path
  *> 10.0.0.0           10.0.1.2                10             0 3 ?
  *> 10.0.0.0/9         10.0.1.2                10             0 3 ?
  *> 10.0.0.0/10        10.0.1.2                10             0 3 ?
  *> 10.0.0.0/11        10.0.1.2                10             0 3 ?
  *> 10.1.0.0/16        10.0.1.2                10             0 3 ?
  *> 10.3.30.0/24       10.0.1.2                10             0 3 ?
  *> 10.3.30.128/25     10.0.1.2                10             0 3 ?
  *> 10.128.0.0/9       10.0.1.2                10             0 3 ?
  *> 10.255.0.0/24      10.0.101.2            1000    555      0 100 e
  *> 10.255.64.0/24     10.0.101.2            1000    555      0 100 e
  ....
  
  
show bgp policy route-policy test2
  
  10.0.0.0/8 is advertised to 10.0.101.2
  
    Path info:
      neighbor:10.0.1.2        neighbor router id:10.0.1.2
      valid  external  best  
    Attributes after inbound policy was applied:
      next hop:10.0.1.2
      MET ORG AS 
      origin:incomplete  neighbor as:3  metric:10  
      aspath:3
    Attributes after outbound policy was applied:
      next hop:10.0.1.2
      MET ORG AS 
      origin:incomplete  neighbor as:3  metric:333  
      aspath:2 3
  ...
  
Table Policy

The table policy attach point allows the user to configure traffic-index values on routes as they are installed into the global routing table. This attach point supports the BGP policy accounting feature. BGP policy accounting uses the traffic indexes that are set on the BGP routes to track various counters. This way, router operators can select different sets of BGP route attributes using the matching operations and then set different traffic indexes for each different class of route they are interested in tracking.

The following example shows how to set the traffic index to 10 in IPv4 unicast routes that originated from autonomous system 10.33. Likewise, any IPv4 unicast routes that originated from autonomous system 11.60 have their traffic index set to 11 when they are installed into the FIB. These traffic indexes are then used to count traffic being forwarded on these routes inline cards by enabling the BGP policy accounting counters on the interfaces of interest.


  route-policy sample-table
    if as-path originates-from ‘10.33’ then
      set traffic-index 10
    elseif as-path originates-from ‘11.60’ then
      set traffic-index 11
    endif
  end-policy
  
  router bgp 2
    address-family ipv4 unicast
      table-policy sample-table
      .
      .
      .
  
Import

The import attach point provides control over the import of routes from the global VPN IPv4 table to a particular VPN routing and forwarding (VRF) instance.

For Layer 3 VPN networks, provider edge (PE) routers learn of VPN IPv4 routes through the Multiprotocol Internal Border Gateway Protocol (MP-iBGP) from other PE routers and automatically filters out route announcements that do not contain route targets that match any import route targets of its VRFs.

This automatic route filtering happens without RPL configuration; however, to provide more control over the import of routes in a VRF, you can configure a VRF import policy.

The following example shows how to perform matches based on a route target extended community and then sets the next hop. If the route has route target value 10:91, then the next hop is set to 172.16.0.1. If the route has route target value 11:92, then the next hop is set to 172.16.0.2. If the route has Site-of-Origin (SoO) value 10:111111 or 10:111222, then the route is dropped. All other non-matching routes are dropped.

When you configure import route policy for a particular VRF, you must define the import route-target values. Configuring import route-policy command does not take effect until you configure the import route-target command with the route-target value. The import route target value acts as a first-level filter. The import policy that you configure using the import route-policy command acts as a second-level filter.


  route-policy bgpvrf_import
    if extcommunity rt matches-any (10:91) then
      set next-hop 172.16.0.1
    elseif extcommunity rt matches-every (11:92) then
      set next-hop 172.16.0.2
    elseif extcommunity soo matches-any (10:111111, 10:111222) then
      pass
    endif
  end-policy
  
  vrf vrf_import
    address-family ipv4 unicast
      import route-policy bgpvrf_import
      .
      .
      .
  
import route-target
         65001:2200
       !
          export route-target
          65001:2201
Export

The export attach point provides control over the export of routes from a particular VRF to a global VPN IPv4 table.

For Layer 3 VPN networks, export route targets are added to the VPN IPv4 routes when VRF IPv4 routes are converted into VPN IPv4 routes and advertised through the MP-iBGP to other PE routers (or flow from one VRF to another within a PE router).

A set of export route targets is configured with the VRF without RPL configuration; however, to set route targets conditionally, you can configure a VRF export policy.

The following example shows some match and set operations supported for the export route policy. If a route matches 172.16.1.0/24 then the route target extended community is set to 10:101, and the weight is set to 211. If the route does not match 172.16.1.0/24 but the origin of the route is egp, then the local preference is set to 212 and the route target extended community is set to 10:101. If the route does not match those specified criteria, then the route target extended community 10:111222 is added to the route. In addition, RT 10:111222 is added to the route that matches any of the previous conditions as well.


  route-policy bgpvrf_export
    if destination in (172.16.1.0/24) then
      set extcommunity rt (10:101)
      set weight 211
    elseif origin is egp then
      set local-preference 212
      set extcommunity rt (10:101)
    endif
    set extcommunity rt (10:111222) additive
  end-policy
  
  vrf vrf-export
    address-family ipv4 unicast
      export route-policy bgpvrf-export
      .
      .
      .
  
Retain Route-Target

The retain route target attach point within BGP allows the specification of match criteria based only on route target extended community. The attach point is useful at the route reflector (RR) or at the Autonomous System Boundary Router (ASBR).

Typically, an RR has to retain all IPv4 VPN routes to peer with its PE routers. These PEs might require routers tagged with different route target IPv4 VPN routes resulting in non-scalable RRs. You can achieve scalability if you configure an RR to retain routes with a defined set of route target extended communities, and a specific set of VPNs to service.

Another reason to use this attach point is for an ASBR. ASBRs do not require that VRFs be configured, but need this configuration to retain the IPv4 VPN prefix information.

The following example shows how to configure the route policy retainer and apply it to the retain route target attach point. The route is accepted if the route contains route target extended communities 10:615, 10:6150, and 15.15.15.15.:15. All other non-matching routes are dropped.


  extcommunity-set rt rtset1
    0:615, 
    10:6150, 
  
  ..15.15.15.15.:15
    end-set
  
  route-policy retainer
    if extcommunity rt matches-any rtset1 then
      pass
    endif
  end-policy
  
  router bgp 2
    address-family vpnv4 unicast
      retain route-target route-policy retainer
      .
      .
      .
  
Allocate-Label

The allocate-label attach point provides increased control based on various attribute match operations. This attach point is typically used in inter-AS option C to decide whether the label should be allocated or not when sending updates to the neighbor for the IPv4 labeled unicast address family. The attribute setting actions supported are for pass and drop.

Label-Mode

The label-mode attachpoint provides facility to choose label mode based on arbitrary match criteria such as prefix value, community. This attach point is typically used to set the type of label mode to per-ce or per-vrf or per-prefix based on deployment preferences. The attribute setting actions supported are for pass and drop.

Neighbor-ORF

The neighbor-orf attach point provides the filtering of incoming BGP route updates using only prefix-based matching. In addition to using this as an inbound filter, the prefixes and disposition (drop or pass) are sent to upstream neighbors as an Outbound Route Filter (ORF) to allow them to perform filtering.

The following example shows how to configure a route policy orf-preset and apply it to the neighbor ORF attach point. The prefix of the route is dropped if it matches any prefix specified in orf-preset (172.16.1.0/24, 172.16.5.0/24, 172.16.11.0/24). In addition to this inbound filtering, BGP also sends these prefix entries to the upstream neighbor with a permit or deny so that the neighbor can filter updates before sending them on to their destination.


  prefix-set orf-preset
    172.16.1.0/24,
    172.16.5.0/24,
    172.16.11.0/24
  end-set
  
  route-policy policy-orf
    if orf prefix in orf-preset then
      drop
    endif
    if orf prefix in (172.16.3.0/24, 172.16.7.0/24, 172.16.13.0/24) then
      pass
    endif
  
  router bgp 2
    neighbor 1.1.1.1
      remote-as 3
      address-family ipv4 unicast
        orf route-policy policy-orf
      .
      .
      .
  
Next-hop

The next-hop attach point provides increased control based on protocol and prefix-based match operations. The attach point is typically used to decide whether to act on a next-hop notification (up or down) event.

Support for next-hop tracking allows BGP to monitor reachability for routes in the Routing Information Base (RIB) that can directly affect BGP prefixes. The route policy at the BGP next-hop attach point helps limit notifications delivered to BGP for specific prefixes. The route policy is applied on RIB routes. Typically, route policies are used in conjunction with next-hop tracking to monitor non-BGP routes.

The following example shows how to configure the BGP next-hop tracking feature using a route policy to monitor static or connected routes with the prefix 10.0.0.0 and prefix length 8.


  route-policy nxthp_policy_A
    if destination in (10.0.0.0/8) and protocol in (static, connected) then
      pass
    endif
  end-policy
  
  router bgp 2
    address-family ipv4 unicast
      nexthop route-policy nxthp_policy_A
        .
        .
        .
  
Clear-Policy

The clear-policy attach point provides increased control based on various AS path match operations when using a clear bgp command. This attach point is typically used to decide whether to clear BGP flap statistics based on AS-path-based match operations.

The following example shows how to configure a route policy where the in operator evaluates to true if one or more of the regular expression matches in the set my-as-set successfully match the AS path associated with the route. If it is a match, then the clear command clears the associated flap statistics.


  as-path-set my-as-set
    ios-regex '_12$',
    ios-regex '_13$'
  end-set
  
  route-policy policy_a
    if as-path in my-as-set then
      pass
    else
      drop
    endif
  end-policy
  
  clear bgp ipv4 unicast flap-statistics route-policy policy_a
  
Debug

The debug attach point provides increased control based on prefix-based match operations. This attach point is typically used to filter debug output for various BGP commands based on the prefix of the route.

The following example shows how to configure a route policy that will only pass the prefix 20.0.0.0 with prefix length 8; therefore, the debug output shows up only for that prefix.


  route-policy policy_b
    if destination in (10.0.0.0/8) then
      pass
    else
      drop
  
    endif
  end-policy
  
  
  debug bgp update  route-policy policy_b
  
BGP Attributes and Operators

This table summarizes the BGP attributes and operators per attach points.

Table 1. BGP Attributes and Operators

Attach Point

Attribute

Match

Set

aggregation

as-path

in

is-local

length

neighbor-is

originates-from

passes-through

unique-length

as-path-length

is, ge, le, eq

as-path-unique-length

is, ge, le, eq

community

is-empty

matches-any

matches-every

set

set additive

delete in

delete not in

delete all

destination

in

extcommunity cost

set

set additive

local-preference

is, ge, le, eq

set

med

is, eg, ge, le

setset +set -

next-hop

in

set

origin

is

set

source

in

suppress-route

suppress-route

weight

set

allocate-label

as-path

in

is-local

length

neighbor-is

originates-from

passes-through

unique-length

as-path-length

is, ge, le, eq

as-path-unique-length

is, ge, le, eq

community

is-empty

matches-any

matches-every

destination

in

label

set

local-preference

is, ge, le, eq

med

is, eg, ge, le

next-hop

in

origin

is

source

in

clear-policy

as-path

in

is-local

length

neighbor-is

originates-from

passes-through

unique-length

as-path-length

is, ge, le, eq

as-path-unique-length

is, ge, le, eq

dampening

as-path

in

is-local

length

neighbor-is

originates-from

passes-through

unique-length

as-path-length

is, ge, le, eq

as-path-unique-length

is, ge, le, eq

community

is-empty

matches-any

matches-every

dampening

—/

set dampening

destination

in

local-preference

is, ge, le, eq

med

is, eg, ge, le

next-hop

in

origin

is

source

in

debug

destination

in

default originate

med

set

set +

set -

rib-has-route

in

neighbor-in

as-path

in

is-local

length

NA

neighbor-is

originates-from

passes-through

unique-length

prepend

prepend most-recent

remove as-path private-as

replace

as-path-length

is, ge, le, eq

as-path-unique-length

is, ge, le, eq

communitycommunity with ‘peeras’

is-empty

matches-any

matches-every

set

set additive

delete-in

delete-not-in

delete-all

destination

in

extcommunity cost

set

set additive

extcommunity rt

is-empty

matches-any

matches-every

matches-within

set

additive

delete-in

delete-not-in

delete-all

extcommunity soo

is-empty

matches-any

matches-every

matches-within

local-preference

is, ge, le, eq

set

med

is, eg, ge, le

set

set +

set -

next-hop

in

set

set peer address

origin

is

set

route-aggregated

route-aggregated

NA

source

in

weight

set

neighbor-out

as-path

in

is-local

length

neighbor-is

originates-from

passes-through

unique-length

prepend

prepend most-recent

remove as-path private-as

replace

as-path-length

is, ge, le, eq

as-path-unique-length

is, ge, le, eq

communitycommunity with ‘peeras’

is-empty

matches-any

matches-every

set

set additive

delete-in

delete-not-in

delete-all

destination

in

extcommunity cost

set

set additive

extcommunity rt

is-empty

matches-any

matches-every

matches-within

set

additive

delete-in

delete-not-in

delete-all

extcommunity soo

is-empty

matches-any

matches-every

matches-within

local-preference

is, ge, le, eq

set

med

is, eg, ge, le

set

set +

set -

set max-unreachable

set igp-cost

next-hop

in

set

set self

origin

is

set

path-type

is

rd

in

route-aggregated

route-aggregated

source

in

unsuppress-route

unsuppress-route

vpn-distinguisher

set

neighbor-orf

orf-prefix

in

n/a

network

as-path

prepend

community

set

set additive

delete-in

delete-not-in

delete-all

destination

in

extcommunity cost

set

set additive

mpls-label

route-has-label

local-preference

set

med

set

set+

set-

next-hop

in

set

origin

set

route-type

is

tag

is, ge, le, eq

weight

set

next-hop

destination

in

protocol

is,in

source

in

redistribute

as-path

prepend

community

set

set additive

delete in

delete not in

delete all

destination

in

extcommunity cost

setset additive

local-preference

set

med

set

set+

set-

next-hop

in

set

origin

set

mpls-label

route-has-label

route-type

is

tag

is, eq, ge, le

weight

set

retain-rt

extcommunity rt

is-empty

matches-any

matches-every

matches-within

show

as-path

in

is-local

length

neighbor-is

originates-from

passes-through

unique-length

as-path-length

is, ge, le, eq

as-path-unique-length

is, ge, le, eq

community

is-empty

matches-any

matches-every

destination

in

extcommunity rt

is-empty

matches-any

matches-every

matches-within

extcommunity soo

is-empty

matches-any

matches-every

matches-within

med

is, eg, ge, le

next-hop

in

origin

is

source

in

Some BGP route attributes are inaccessible from some BGP attach points for various reasons. For example, the set med igp-cost only command makes sense when there is a configured igp-cost to provide a source value.

This table summarizes which operations are valid and where they are valid.

Table 2. Restricted BGP Operations by Attach Point

Command

import

export

aggregation

redistribution

prepend as-path most-recent

eBGP only

eBGP only

n/a

n/a

replace as-path

eBGP only

eBGP only

n/a

n/a

set med igp-cost

forbidden

eBGP only

forbidden

forbidden

set weight

n/a

forbidden

n/a

n/a

suppress

forbidden

forbidden

n/a

forbidden

Default-Information Originate

The default-information originate attach point allows the user to conditionally inject the default route 0.0.0.0/0 into the OSPF link-state database, which is done by evaluating the attached policy. If any routes in the local RIB pass the policy, then the default route is inserted into the link-state database.

The following example shows how to generate a default route if any of the routes that match 10.0.0.0/8 ge 8 le 25 are present in the RIB:


  route-policy ospf-originate
    if rib-has-route in (10.0.0.0/8 ge 8 le 25) then
      pass
    endif
  end-policy
  
  router ospf 1
    default-information originate policy ospf-originate
    .
    .
    .
  

OSPF Policy Attach Points

This section describes each of the OSPF policy attach points and provides a summary of the OSPF attributes and operators.

Redistribute

The redistribute attach point within OSPF injects routes from other routing protocol sources into the OSPF link-state database, which is done by selecting the routes it wants to import from each protocol. It then sets the OSPF parameters of cost and metric type. The policy can control how the routes are injected into OSPF by using the set metric-type or set ospf-metric command.

The following example shows how to redistribute routes from IS-IS instance instance_10 into OSPF instance 1 using the policy OSPF-redist. The policy sets the metric type to type-2 for all redistributed routes. IS-IS routes with a tag of 10 have their cost set to 100, and IS-IS routes with a tag of 20 have their OSPF cost set to 200. Any IS-IS routes not carrying a tag of either 10 or 20 are not be redistributed into the OSPF link-state database.


  route-policy OSPF-redist
    set metric-type type-2
    if tag eq 10 then
  
   ..set ospf-metric  2
    elseif tag eq 20 then
  
   ..set ospf-metric   3
    else
      drop
    endif
  end-policy
  router ospf 1
    redistribute isis instance_10 policy OSPF-redist
    .
    .
    .
  
Area-in

The area-in attach point within OSPF allows you to filter inbound OSPF type-3 summary link-state advertisements (LSAs). The attach point provides prefix-based matching and hence increased control for filtering type-3 summary LSAs.

The following example shows how to configure the prefix for OSPF summary LSAs. If the prefix matches any of 10 .105.3.0/24, 10 .105.7.0/24, 10 .105.13.0/24, it is accepted. If the prefix matches any of 10 .106.3.0/24, 10 .106.7.0/24, 10 .106.13.0/24, it is dropped.


  route-policy OSPF-area-in
    if destination in (10
.105.3.0/24, 10
.105.7.0/24, 10
.105.13.0/24) then
      drop
    endif
    if destination in (10
.106.3.0/24, 10
.106.7.0/24, 10
.106.13.0/24) then
      pass
    endif
  end-policy
  
  router ospf 1
    area 1
      route-policy OSPF-area-in in 
  
Area-out

The area-out attach point within OSPF allows you to filter outbound OSPF type-3 summary LSAs. The attach point provides prefix-based matching and, hence, increased control for filtering type-3 summary LSAs.

The following example shows how to configure the prefix for OSPF summary LSAs. If the prefix matches any of 11 .105.3.0/24, 11 .105.7.0/24, 11 .105.13.0/24, it is announced. If the prefix matches any of 10.105.3.0/24, 10 .105.7.0/24, 10 .105.13.0/24, it is dropped and not announced.

route-policy OSPF-area-out
    if destination in (10
.105.3.0/24, 10
.105.7.0/24, 10
.105.13.0/24) then
      drop
    endif
    if destination in (11
.105.3.0/24, 11
.105.7.0/24, 11
.105.13.0/24) then
      pass
    endif
  end-policy
  
  router ospf 1
    area 1
      route-policy OSPF-area-out out
  
OSPF Attributes and Operators

This table summarizes the OSPF attributes and operators per attach points.

Table 3. OSPF Attributes and Operators

Attach Point

Attribute

Match

Set

default-information originate

ospf-metric

set

metric-type

set

tag

set

rib-has-route

in

redistribute

destination

in

metric-type

set

ospf-metric

set

next-hop

in

mpls-label

route-has-label

rib-metric

is, le, ge, eq

n/a

route-type

is

tag

is, eq, ge, le

set

area-in

destination

in

area-out

destination

in

spf-prefix-priority

destination

in

n/a

spf-priority

n/a

set

tag

is, le, ge, eq

n/a

Distribute-list in

The distribute-list in attach point within OSPF allows use of route policies to filter OSPF prefixes. The distribute-list in route-policy can be configured at OSPF instance, area, and interface levels. The route-policy used in the distribute-list in command supports match statements, "destination" and "rib-metric". The "set" commands are not supported in the route-policy.

These are examples of valid route-policies for "distribute-list in":

route-policy DEST
  if destination in (10.10.10.10/32) then
    drop
  else
    pass
  endif
end-policy


route-policy METRIC
  if rib-metric ge 10 and rib-metric le 19 then
    drop
  else
    pass
  endif
end-policy


prefix-set R-PFX
  10.10.10.30
end-set

route-policy R-SET
  if destination in R-PFX and rib-metric le 20 then
    pass
  else
    drop
  endif
end-policy

OSPFv3 Policy Attach Points

This section describes each of the OSPFv3 policy attach points and provides a summary of the OSPFv3 attributes and operators.

Redistribute

The redistribute attach point within OSPFv3 injects routes from other routing protocol sources into the OSPFv3 link-state database, which is done by selecting the route types it wants to import from each protocol. It then sets the OSPFv3 parameters of cost and metric type. The policy can control how the routes are injected into OSPFv3 by using the metric type command.

The following example shows how to redistribute routes from BGP instance 15 into OSPF instance 1 using the policy OSPFv3-redist. The policy sets the metric type to type-2 for all redistributed routes. BGP routes with a tag of 10 have their cost set to 100, and BGP routes with a tag of 20 have their OSPFv3 cost set to 200. Any BGP routes not carrying a tag of either 10 or 20 are not be redistributed into the OSPFv3 link-state database.


  route-policy OSPFv3-redist
    set metric-type type-2
    if tag eq 10 then
      set extcommunity cost 100
    elseif tag eq 20 then
      set extcommunity cost 200
    else
      drop
    endif
  end-policy
  
  router ospfv3 1
    redistribute bgp 15 policy OSPFv3-redist
    .
    .
    .
  
OSPFv3 Attributes and Operators

This table summarizes the OSPFv3 attributes and operators per attach points.

Table 4. OSPFv3 Attributes and Operators

Attach Point

Attribute

Match

Set

default-information originate

ospf-metric

set

metric-type

set

tag

set

rib-has-route

in

redistribute

destination

in

ospf-metric

set

metric-type

set

route-type

is

tag

is, eq, ge, le

IS-IS Policy Attach Points

This section describes each of the IS-IS policy attach points and provides a summary of the IS-IS attributes and operators.

Default-Information Originate

The default-information originate attach point within IS-IS allows the default route 0.0.0.0/0 to be conditionally injected into the IS-IS route database.

The following example shows how to generate an IPv4 unicast default route if any of the routes that match 10.0.0.0/8 ge 8 le 25 is present in the RIB. The cost of the IS-IS route is set to 100 and the level is set to level-1-2 on the default route that is injected into the IS-IS database.


  route-policy isis-originate
    if rib-has-route in (10.0.0.0/8 ge 8 le 25) then
  
      set level level-1-2
    endif
  end-policy
  
  router isis instance_10
    address-family ipv4 unicast
      default-information originate policy isis_originate
      .
  
Inter-area-propagate

The inter-area-propagate attach point within IS-IS allows the prefixes to be conditionally propagated from one level to another level within the same IS-IS instance.

The following example shows how to allow prefixes to be leaked from the level 1 LSP into the level 2 LSP if any of the prefixes match 10.0.0.0/8 ge 8 le 25.


  route-policy isis-propagate
    if destination in (10.0.0.0/8 ge 8 le 25) then
      pass
    endif
  end-policy
  
  
  router isis instance_10
    address-family ipv4 unicast
      propagate level 1 into level 2 policy isis-propagate
      .
  

Nondestructive Editing of Routing Policy

The Nondestructive Editing of Routing Policy changes the default exit behavior under routing policy configuration mode to terminate the configuration.

The default exit command acts as end-policy, end-set, or end-if. If the exit command is executed under route policy configuration mode, the changes are applied and configuration is updated. This destructs the existing policy. The rpl set-exit-as-abort command allows to overwrite the default behavior of the exit command under the route policy configuration mode.

Attached Policy Modification

Policies that are in use do, on occasion, need to be modified. In the traditional configuration model, a policy modification would be done by completely removing the policy and reentering re-entering it. However, this model allows for a window of time in which no policy is attached and default actions to be used, which is an opportunity for inconsistencies to exist. To close this window of opportunity, you can modify a policy in use at an attach point by respecifying it, which allows for policies that are in use to be changed, without having a window of time in which no policy is applied at the given attach point.


Note


A route policy or set that is in use at an attach point cannot be removed because this removal would result in an undefined reference. An attempt to remove a route policy or set that is in use at an attach point results in an error message to the user.


Nonattached Policy Modification

As long as a given policy is not attached at an attach point, the policy is allowed to refer to nonexistent sets and policies. Configurations can be built that reference sets or policy blocks that are not yet defined, and then later those undefined policies and sets can be filled in. This method of building configurations gives much greater flexibility in policy definition. Every piece of policy you want to reference while defining a policy need not exist in the configuration. Thus, you can define a policy sample1 that references a policy sample2 using an apply statement even if the policy sample2 does not exist. Similarly, you can enter a policy statement that refers to a nonexistent set.

However, the existence of all referenced policies and sets is enforced when a policy is attached. Thus, if a user attempts to attach the policy sample1 with the reference to an undefined policy sample2 at an inbound BGP policy using the statement neighbor 1.2.3.4 address-family ipv4 unicast policy sample1 in, the configuration attempt is rejected because the policy sample2 does not exist.

Editing Routing Policy Configuration Elements

RPL is based on statements rather than on lines. That is, within the begin-end pair that brackets policy statements from the CLI, a new line is merely a separator, the same as a space character.

The CLI provides the means to enter and delete route policy statements. RPL provides a means to edit the contents of the policy between the begin-end brackets, using a text editor. The following text editors are available on the software for editing RPL policies:

  • Nano (default)

  • Emacs

  • Vim

Editing Routing Policy Configuration Elements Using Emacs Editor

To edit the contents of a routing policy using the Emacs editor, use the following CLI command in XR EXEC mode:


  
         edit 
         
            route-policy
           
         
            name 
  
            emacs
  
           
  
  
      

A copy of the route policy is copied to a temporary file and the editor is launched. After editing, save the editor buffer by using the Ctrl-X and Ctrl-S keystrokes. To save and exit the editor, use the Ctrl-X and Ctrl-C keystrokes. When you quit the editor, the buffer is committed. If there are no parse errors, the configuration is committed:


  RP/0/RP0/CPU0:router# edit route-policy policy_A
  ----------------------------------------
  == MicroEMACS 3.8b () == rpl_edit.139281 ==
    if destination in (2001::/8) then
      drop
    endif
  end-policy
  !
  
  == MicroEMACS 3.8b () == rpl_edit.139281 ==
  Parsing.
  83 bytes parsed in 1 sec (82)bytes/sec
  Committing.
  1 items committed in 1 sec (0)items/sec
  Updating.
  Updated Commit database in 1 sec 
  
  

If there are parse errors, you are asked whether editing should continue:


  RP/0/RP0/CPU0:router#edit route-policy policy_B
  == MicroEMACS 3.8b () == rpl_edit.141738
  route-policy policy_B
   set metric-type type_1
   if destination in (2001::/8) then
      drop
    endif  
  end-policy
  !
  == MicroEMACS 3.8b () == rpl_edit.141738 ==
  Parsing.
  105 bytes parsed in 1 sec (103)bytes/sec
  
  % Syntax/Authorization errors in one or more commands.!! CONFIGURATION 
  FAILED DUE TO SYNTAX/AUTHORIZATION ERRORS
   set metric-type type_1
   if destination in (2001::/8) then
      drop
    endif
  end-policy
  !
  
  Continue editing? [no]:
  
  

If you answer yes, the editor continues on the text buffer from where you left off. If you answer no, the running configuration is not changed and the editing session is ended.

Editing Routing Policy Configuration Elements Using Vim Editor

Editing elements of a routing policy with Vim (Vi IMproved) is similar to editing them with Emacs except for some feature differences such as the keystrokes to save and quit. To write to a current file and exit, use the :wq or :x or ZZ keystrokes. To quit and confirm, use the :q keystrokes. To quit and discard changes, use the :q! keystrokes.

You can reference detailed online documentation for Vim at this URL: http://www.vim.org/

Editing Routing Policy Configuration Elements Using CLI

The CLI allows you to enter and delete route policy statements. You can complete a policy configuration block by entering applicable commands such as end-policy or end-set. Alternatively, the CLI interpreter allows you to use the exit command to complete a policy configuration block. The abort command is used to discard the current policy configuration and return to mode.

Editing Routing Policy Configuration Elements Using Nano Editor

To edit the contents of a routing policy using the Nano editor, use the following CLI command in XR EXEC mode:


  
         edit route-policy 
         
            name
           
         
            nano
           
  
  
      

A copy of the route policy is copied to a temporary file and the editor is launched. After editing, enter Ctrl-X to save the file and exit the editor. The available editor commands are displayed on screen.

Detailed information on using the Nano editor is available at this URL: http://www.nano-editor.org/.

Not all Nano editor features are supported on the software.

Editing Routing Policy Language set elements Using XML

RPL supports editing set elements using XML. Entries can be appended, prepended, or deleted to an existing set without replacing it through XML.

Hierarchical Policy Conditions

The Hierarchical Policy Conditions feature enables the ability to specify a route policy within the "if" statement of another route policy. This ability enables route-policies to be applied for configurations that are based on hierarchical policies.

With the Hierarchical Policy Conditions feature, the software supports Apply Condition policies that can be used with various types of Boolean operators along with various other matching statements.

Apply Condition Policies

Apply Condition policies allow usage of a route-policy within an "if" statement of another route-policy.

Consider route-policy configurations Parent , Child A , and Child B :
route-policy ChildA
 if destination in (10.10.0.0/16) then
  set local-pref 111
 endif
end-policy
!
route-policy ChildB
 if as-path originates-from '222' then
  set community (333:222) additive
 endif
end-policy
!
route-policy Parent
 if apply ChildA and apply ChildB then
  set community (333:333) additive
 else
  set community (333:444) additive
 endif
end-policy
!

In the above scenarios, whenever the policy Parent is executed, the decision of the "if" condition in that is selected based on the result of policies Child A and Child B . The policy Parent is equivalent to policy merged as given below:

route-policy merged
 if destination in (10.10.0.0/16) and as-path originates-from '222' then
  set local-pref 111
  set community (333:222, 333:333) additive
 elseif destination in (10.10.0.0/16) then /*Only Policy ChildA is pass */
  set local-pref 111
  set community (333:444) additive	/*From else block */
 elseif as-path originates-from '222' then /*Only Policy ChildB is pass */
  set community (333:222, 333:444) additive /*From else block */
 else
  set community (333:444) additive /*From else block */
 endif
end-policy

Apply Conditions can be used with parameters and are supported on all attach points and on all clients. Hierarchical Apply Conditions can be used without any constraints on a cascaded level.

Existing route policy semantics can be expanded to include this Apply Condition:

Route-policy policy_name
 If apply policyA and apply policyB then
      Set med 100
 Else if not apply policyD then
      Set med 200
 Else
    Set med 300
 Endif
End-policy
Behavior of pass/drop/done RPL Statements for Simple Hierarchical Policies

This table describes the behavior of pass /drop /done RPL statements, with a possible sequence for executing the done statement for Simple Hierarchical Policies.

Route-policies with simple hierarchical policies Possible done statement execution sequence Behavior
pass

pass

Continue_list

Marks the prefix as "acceptable" and continues with execution of continue_list statements.
drop

Stmts_list

drop

Rejects the route immediately on hitting the drop statement and stops policy execution.
done

Stmts_list

done

Accepts the route immediately on hitting the done statement and stops policy execution.
pass followed by done

pass

Statement_list

done

Exits immediately at the done statement with "accept route".
drop followed by done

drop

Statement list

done

This is an invalid scenario at execution point of time. Policy terminates execution at the drop statement itself, without going through the statement list or the done statement; the prefix will be rejected or dropped.
Behavior of pass/drop/done RPL Statements for Hierarchical Policy Conditions

This section describes the behavior of pass /drop /done RPL statements, with a possible sequence for executing the done statement for Hierarchical Policy Conditions.

Terminology for policy execution: "true-path", "false-path", and "continue-path".


Route-policy parent
  If apply hierarchical_policy_condition then
     TRUE-PATH         : if hierarchical_policy_condition  returns TRUE then this path will be executed.
  Else
     FALSE-PATH       : if hierarchical_policy_condition  returns FALSE then this path will be executed.
  End-if
  CONTINUE-PATH             : Irrespective of the TRUE/FALSE this path will be executed.
 End-policy

Hierarchical policy conditions Possible done statement execution sequence Behavior
pass

pass

Continue_list

Marks the return value as "true" and continues execution within the same policy condition.

If there is no statement after "pass ", returns "true".

pass followed by done

pass or set action statement

Stmt_list

done

Marks the return value as "true" and continues execution till the done statement. Returns "true" to the apply policy condition to take "true-path".
done

Stmt_list without pass or set operation

DONE

Returns " false". Condition takes "false-path".
drop

Stmt_list

drop

Stmt_list

The prefix is dropped or rejected.

Nested Wildcard Apply Policy

The hierarchical constructs of Routing Policy Language (RPL) allows one policy to refer to another policy. The referred or called policy is known as a child policy. The policy from which another policy is referred is called calling or parent policy. A calling or parent policy can nest multiple child policies for attachment to a common set of BGP neighbors. The nested wildcard apply policy allows wildcard (*) based apply nesting. The wildcard operation permits declaration of a generic apply statement that calls all policies that contain a specific defined set of alphanumeric characters, defined on the router.

A wildcard is specified by placing an asterisk (*) at the end of the policy name in an apply statement. Passing parameters to wildcard policy is not supported. The wildcard indicates that any value for that portion of the apply policy matches.

To illustrate nested wildcard apply policy, consider this policy hierarchy:
route-policy Nested_Wilcard
apply service_policy_customer*
end-policy

route-policy service_policy_customer_a
if destination in prfx_set_customer_a  then
set extcommunity rt (1:1) additive 
endif
end-policy

route-policy service_policy_customer_b
if destination in prfx_set_customer_b then
set extcommunity rt (1:1) additive
endif
end-policy

route-policy service_policy_customer_c
if destination in prfx_set_customer_c then
set extcommunity rt (1:1) additive
endif
end-policy

Here, a single parent apply statement (apply service_policy_customer*) calls (inherits) all child polices that contain the identified character string "service_policy_customer". As each child policy is defined globally, the parent dynamically nests the child policies based on the policy name. The parent is configured once and inherits each child policy on demand. There is no direct association between the parent and the child policies beyond the wildcard match statement.

VRF Import Policy Enhancement

The VRF RPL based import policy feature provides the ability to perform import operation based solely on import route-policy, by matching on route-targets (RTs) and other criteria specified within the policy. No need to explicitly configure import RTs under global VRF-address family configuration mode. If the import RTs and import route-policy is already defined, then the routes will be imported from RTs configured under import RT and then follows the route-policy attached at import route-policy.

Use the source rt import-policy command under VRF sub-mode of VPN address-family configuration mode to enable this feature.

Match Aggregated Route

The Match Aggregated Route feature helps to match BGP aggregated route from the non-aggregated route. BGP can aggregate a group of routes into a single prefix before sending updates to a neighbor. With Match Aggregated Route feature, route policy separates this aggregated route from other routes.

Remove Private AS in Inbound Policy

BGP appends its own as-path before sending out packets to neighbors. When a packet traverses multiple iBGP neighbors, the as-path structure will have many private autonomous systems (AS) in them. The Remove Private AS in Inbound Policy will give the capability to delete those private autonomous systems using RPL route-policy. The remove as-path private-as command removes autonomous systems (AS) with AS number 64512 through 65535.