Implementing the Dynamic Host Configuration Protocol

This module describes the concepts and tasks you will use to configure Dynamic Host Configuration Protocol (DHCP).


Note


For a complete description of the DHCP commands listed in this module, refer to the Cisco ASR 9000 Series Aggregation Services Router IP Addresses and Services Command Reference publication.


Feature History for Implementing the Dynamic Host Configuration Protocol

Release

Modification

Release 3.7.2

This feature was introduced .

Prerequisites for Configuring DHCP Relay Agent

The following prerequisites are required to configure a DHCP relay agent:

  • You must be in a user group associated with a task group that includes the proper task IDs. The command reference guides include the task IDs required for each command. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

  • A configured and running DHCP client and DHCP server

  • Connectivity between the relay agent and DHCP server

Information About DHCP Relay Agent

A DHCP relay agent is a host that forwards DHCP packets between clients and servers that do not reside on a shared physical subnet. Relay agent forwarding is distinct from the normal forwarding of an IP router where IP datagrams are switched between networks transparently.

DHCP clients use User Datagram Protocol (UDP) broadcasts to send DHCPDISCOVER messages when they lack information about the network to which they belong.

If a client is on a network segment that does not include a server, a relay agent is needed on that network segment to ensure that DHCP packets reach the servers on another network segment. UDP broadcast packets are not forwarded, because most routers are not configured to forward broadcast traffic. You can configure a DHCP relay agent to forward DHCP packets to a remote server by configuring a DHCP relay profile and configure one or more helper addresses in it. You can assign the profile to an interface or a VRF.

Forwarding UDP Broadcasts to a DHCP Server Using a Helper Address demonstrates the process. The DHCP client broadcasts a request for an IP address and additional configuration parameters on its local LAN. Acting as a DHCP relay agent, Router B picks up the broadcast, changes the destination address to the DHCP server's address and sends the message out on another interface. The relay agent inserts the IP address of the interface, on which the DHCP client’s packets are received, into the gateway address (giaddr) field of the DHCP packet, which enables the DHCP server to determine which subnet should receive the offer and identify the appropriate IP address range. The relay agent unicasts the messages to the server address, in this case 172.16.1.2 (which is specified by the helper address in the relay profile).

Figure 1. Forwarding UDP Broadcasts to a DHCP Server Using a Helper Address

Limitations for DHCPv6 Relay Feature

These are the limitations for implementing DHCPv6 relay feature:

  • The multicast addresses are not supported. The helper-address command in DHCPv6 relay profile submode will only support global unicast IPv6 address as the helper address.

  • Only one relay is supported between client and server with an exception of Lightweight DHCPv6 Relay Agent (LRDA) being present on the access side. That is, the Layer 3 relay packets are not supported.

  • Only interface-id and remote-id DHCPv6 option code are added by a relay agent while forwarding the packet to a DHCPv6 server.

    Note


    Configuring DHCPv6 option code is not supported in DHCPv6 relay profile submode.


Secure ARP

In standalone DHCP sessions, the DHCP server adds an ARP entry when it assigns an IP address to a client. However, in IP subscriber sessions, DHCP server does not add an ARP entry. Although ARP establishes correspondences between network addresses, an untrusted device can spoof IP an address not assigned to it posing a security threat for IP subscriber sessions. You can enable the secure ARP feature and allow DHCP to add an ARP cache entry when DHCP assigns an IP address to a client. Secure ARP is disabled by default.

How to Configure and Enable DHCP Relay Agent

This section contains the following tasks:

Configuring and Enabling DHCP Relay Agent with DHCP MAC Address Verification

This section discusses how to configure and enable DHCP Relay Agent with DHCP MAC address verification.

Configuration Example

Router# configure

Router(config)# dhcp ipv4
/* Configures DHCP for IPv4 and enters the DHCPv4 configuration submode. */

Router(config-dhcpv4)# profile client relay
/* Enables DHCP relay profile */

Router(config-dhcpv4)# client-mac-mismatch action drop
/* Enables MAC address verification. If MAC address in the DHCPv4 protocol header does not match the L2 header source MAC address in the DHCPv4 relay profile,
 the frame is dropped  */

Router(config-dhcpv4-relay-profile)# relay information option
/* Inserts the DHCP relay agent information option (option-82 field) in forwarded 
BOOTREQUEST messages to a DHCP server. */

Router(config-dhcpv4-relay-profile)# relay information check
/* (Optional) Configures DHCP to check the validity of the relay agent information 
option in forwarded BOOTREPLY messages. */

Router(config-dhcpv4-relay-profile)# relay information policy drop
/* (Optional) Configures the reforwarding policy for a DHCP relay agent; 
that is, whether the relay agent will drop or keep (using the 'keep' keyword)
 the relay information. */

Router(config-dhcpv4-relay-profile)# relay information option allow-untrusted
/* (Optional) Configures the DHCP IPv4 Relay not to discard BOOTREQUEST packets that have an existing 
relay information option and the giaddr set to zero. */

Router(config-dhcpv4-relay-profile)# giaddr policy drop
/* Drops the packet that has an existing nonzero giaddr value. Use the 'replace' keyword
 to replace the existing giaddr value with a value that it generates (the default behavior).  */

Router(config-dhcpv4-relay-profile)# helper-address vrf vrf1 10.1.1.1
/* Forwards UDP broadcasts, including DHCP. */

Router(config-dhcpv4-relay-profile)# commit

Router(config-dhcpv4-relay-profile)# exit
Router(config-dhcpv4)# vrf vrf1 relay profile client
Router(config-dhcpv4)# commit
/* Configures DHCP Relay on a VRF and commits the entire configuration. */

Running Configuration

Confirm your configuration.

Router# show run
Thu May 11 09:00:57.839 IST
Building configuration...
!! IOS XR Configuration 0.0.0
!! Last configuration change at Thu May 11 09:00:54 2017 by annseque
!
dhcp ipv4
vrf vrf1 relay profile client
profile client relay
client-mac-match action drop
helper-address vrf vrf1 10.1.1.1
giaddr policy drop
relay information check
relay information option
relay information policy drop
relay information option allow-untrusted
!
!

DHCP MAC Address Verification

Use the following show command to check if DHCP MAC address is being verified on the router.

Router# show dhcp ipv4 relay statistics raw all
packet_drop_mac_mismatch                      :         0

The output validates that the DHCP MAC address of the packets is verified.

Configuring the DHCPv6 (Stateless) Relay Agent

Perform this task to specify a destination address to which client messages are forwarded and to enable Dynamic Host Configuration Protocol (DHCP) for IPv6 relay service on the interface.

Configuration Example

To configure the DHCPv6 (stateless) relay agent, you must complete the following configurations:
  1. Enable the DHCP IPv6 configuration mode.

  2. Configure the DHCPv6 relay profile.

  3. Configure helper addresses.

  4. Specify the interface for the relay profile.

Configuration


/* Enter the global configuration mode, and then enter the DHCP IPv6 configuration mode */
Router# configure terminal
Router(config)# dhcp ipv6
Router(config-dhcpv6)# profile test relay
Router(config-dhcpv6-relay-profile)# helper-address vrf default 2001:1::1
Router(config-dhcpv6-relay-profile)# !
Router(config-dhcpv6-relay-profile)# interface TenGigE0/0/0/0 relay profile test
Router(config-dhcpv6)# !

Enabling DHCP Relay Agent on an Interface

This task describes how to enable the Cisco IOS XR DHCP relay agent on an interface.


Note


On Cisco IOS XR software, the DHCP relay agent is disabled by default.


SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. interface type name relay profile profile-name
  4. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:


RP/0/RSP0/CPU0:router(config)# dhcp ipv4 

Enters DHCP IPv4 configuration submode.

Step 3

interface type name relay profile profile-name

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4)# interface gigabitethernet 0/0/0
/0 relay profile client

Attaches a relay profile to an interface.

Step 4

commit

Enabling DHCPv6 Relay Agent on an Interface

This task describes how to enable the DHCPv6 relay agent on an interface.

SUMMARY STEPS

  1. configure
  2. dhcp ipv6
  3. interface type interface-instance relay profile profile-name
  4. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Example:


RP/0/RSP0/CPU0:router# configure

Enters global configuration mode.

Step 2

dhcp ipv6

Example:


RP/0/RSP0/CPU0:router(config)# dhcp ipv6 

Configures DHCP for IPv6 and enters the DHCPv6 configuration submode.

Step 3

interface type interface-instance relay profile profile-name

Example:


RP/0/RSP0/CPU0:router(config-dhcpv6)# interface gigabitethernet 0/0/0/0 relay profile client 
Attaches a relay profile to an interface.

Step 4

commit

Enabling DHCPv6 Relay Agent on an Interface: Example


 configure
 dhcp ipv6
 interface gigabitethernet 0/0/0/0 relay profile client
 !
end

Disabling DHCP Relay on an Interface

This task describes how to disable the DHCP relay on an interface by assigning the none profile to the interface.

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. interface type name none
  4. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:


RP/0/RSP0/CPU0:router(config)# dhcp ipv4

Enters DHCP IPv4 configuration submode.

Step 3

interface type name none

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# interface gigabitethernet 
0/1/4/1 none

Disables the DHCP relay on the interface.

Step 4

commit

Enabling DHCP Relay on a VRF

This task describes how to enable DHCP relay on a VRF.

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. vrf vrf-name relay profile profile-name
  4. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:


RP/0/RSP0/CPU0:router(config)# dhcp ipv4

Enters DHCP IPv4 configuration submode.

Step 3

vrf vrf-name relay profile profile-name

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4)# 
vrf default relay profile client

Enables DHCP relay on a VRF.

Step 4

commit

Configuring the Relay Agent Information Feature

This task describes how to configure the DHCP relay agent information option processing capabilities.

A DHCP relay agent may receive a message from another DHCP relay agent that already contains relay information. By default, the relay information from the previous relay agent is replaced (using the replace option).

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. profile profile-name relay
  4. relay information option
  5. relay information check
  6. relay information policy {drop | keep}
  7. relay information option allow-untrusted
  8. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:


RP/0/RSP0/CPU0:router(config)# dhcp ipv4

Enters DHCP IPv4 configuration submode .

Step 3

profile profile-name relay

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4)# profile client relay

Enters DHCP IPv4 profile relay submode .

Step 4

relay information option

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# relay information option

Enables the system to insert the DHCP relay agent information option (option-82 field) in forwarded BOOTREQUEST messages to a DHCP server.

  • This option is injected by the relay agent while forwarding client-originated DHCP packets to the server. Servers recognizing this option can use the information to implement IP address or other parameter assignment policies. When replying, the DHCP server echoes the option back to the relay agent. The relay agent removes the option before forwarding the reply to the client.

  • The relay agent information is organized as a single DHCP option that contains one or more suboptions. These options contain the information known by the relay agent.

    The supported suboptions are:

    • Remote ID

    • Circuit ID

Note

 

This function is disabled by default.

The port field of the default circuit-ID denotes the configured bundle-ID of the bundle. If circuit IDs require that bundles be unique, and because the port field is 8 bits, the low-order 8 bits of configured bundle IDs must be unique. To achieve this, configure bundle-IDs within the range from 0 to 255.

Step 5

relay information check

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# relay information check

(Optional) Configures DHCP to check the validity of the relay agent information option in forwarded BOOTREPLY messages. If an invalid message is received, the relay agent drops the message. If a valid message is received, the relay agent removes the relay agent information option field and forwards the packet.

  • By default, DHCP does not check the validity of the relay agent information option field in DHCP reply packets, received from the DHCP server.

Note

 

Use the relay information check command to reenable this functionality if the functionality has been disabled.

Step 6

relay information policy {drop | keep}

Example:


RP/0/RSP0/CPU0:router(config)# dhcp relay information policy drop

(Optional) Configures the reforwarding policy for a DHCP relay agent; that is, whether the relay agent will drop or keep the relay information.

By default, the DHCP relay agent replaces the relay information option.

Step 7

relay information option allow-untrusted

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# relay information option allow-untrusted

(Optional) Configures the DHCP IPv4 Relay not to discard BOOTREQUEST packets that have an existing relay information option and the giaddr set to zero.

Step 8

commit

Configuring Relay Agent Giaddr Policy

This task describes how to configure the DHCP relay agent’s processing capabilities for received BOOTREQUEST packets that already contain a nonzero giaddr attribute.

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. profile relay
  4. giaddr policy {replace | drop}
  5. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:


RP/0/RSP0/CPU0:router(config)# dhcp ipv4

Enables the DHCP IPv4 configuration submode.

Step 3

profile relay

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4)# profile client relay

Enables profile relay submode.

Step 4

giaddr policy {replace | drop}

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# giaddr policy drop

Specifies the giaddr policy.

  • replaceReplaces the existing giaddr value with a value that it generates.

  • dropDrops the packet that has an existing nonzero giaddr value.

By default, the DHCP relay agent keeps the existing giaddr value.

Step 5

commit

Configuring a DHCPv4 Relay Profile with Multiple Helper Addresses

You can configure up to 16 helper addresses for a DHCPv4 relay profile, as shown in the following example.

  1. Enter the DHCPv4 configuration mode.

    RP/0/RSP0/CPU0:router(config)# dhcp ipv4
  2. Configure the DHCPv4 relay profile.

    RP/0/RSP0/CPU0:router(config-dhcpv4)# profile helper relay
  3. Configure helper addresses.

    You can configure up to 16 IPv4 addresses.

    
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 1.1.1.1
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 2.2.2.2
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 3.3.3.3
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 4.4.4.4
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 5.5.5.5
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 6.6.6.6
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 7.7.7.7
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 8.8.8.8
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 9.9.9.9
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 10.10.10.10
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 11.11.11.11
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 12.12.12.12
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 13.13.13.13
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 14.14.14.14
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 15.15.15.15
    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# helper-address vrf default 16.16.16.16
  4. Confirm your configuration.

    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# show configuration
    Thu Feb  2 13:49:15.605 IST
    Building configuration...
    !! IOS XR Configuration 0.0.0
    dhcp ipv4
     profile helper relay
      helper-address vrf default 1.1.1.1
      helper-address vrf default 2.2.2.2
      helper-address vrf default 3.3.3.3
      helper-address vrf default 4.4.4.4
      helper-address vrf default 5.5.5.5
      helper-address vrf default 6.6.6.6
      helper-address vrf default 7.7.7.7
      helper-address vrf default 8.8.8.8
      helper-address vrf default 9.9.9.9
      helper-address vrf default 10.10.10.10
      helper-address vrf default 11.11.11.11
      helper-address vrf default 12.12.12.12
      helper-address vrf default 13.13.13.13
      helper-address vrf default 14.14.14.14
      helper-address vrf default 15.15.15.15
      helper-address vrf default 16.16.16.16
     !
    !
    end
  5. Commit your configuration.

    RP/0/RSP0/CPU0:router(config-dhcpv4-relay-profile)# commit
  6. Exit the configuration mode and verify the configured helper addresses.

    RP/0/RSP0/CPU0:router# show dhcp ipv4 relay profile name helper
    ...
    Profile: helper
    Helper Addresses:
            1.1.1.1, vrf default
            2.2.2.2, vrf default
            3.3.3.3, vrf default
            4.4.4.4, vrf default
            5.5.5.5, vrf default
            6.6.6.6, vrf default
            7.7.7.7, vrf default
            8.8.8.8, vrf default
            9.9.9.9, vrf default
            10.10.10.10, vrf default
            10.10.10.11, vrf default
            10.10.10.13, vrf default
            10.10.10.14, vrf default
            10.10.10.15, vrf default
            10.10.10.16, vrf default
            10.10.10.17, vrf default
    Information Option: Disabled
    Information Option Allow Untrusted: Disabled
    Information Option VPN: Disabled
    Information Option VPN Mode: RFC
    Information Option Policy: Replace
    Information Option Check: Disabled
    GIADDR Policy: Keep
    Broadcast-flag Policy: Ignore
    VRF References:
    Interface References:
    

    You have successfully configured multiple DHCPv4 relay helper addresses.

Configuring a DHCP Proxy Profile

The DHCP proxy performs all the functions of a relay and also provides some additional functions. The DHCP proxy conceals DHCP server details from DHCP clients. The DHCP proxy modifies the DHCP replies such that the client considers the proxy to be the server. In this state, the client interacts with the proxy as if it is the DHCP server.

This task describes how to configure and enable the DHCP proxy profile.

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. profile profile-name proxy
  4. helper-address [vrf vrf- name ] address [ giaddr gateway-address ]
  5. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:


RP/0/RSP0/CPU0:router(config)# dhcp ipv4

Enters DHCP IPv4 configuration submode .

Step 3

profile profile-name proxy

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4)# profile client proxy

Enters DHCP IPv4 profile proxy submode.

Step 4

helper-address [vrf vrf- name ] address [ giaddr gateway-address ]

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4-proxy-profile)# helper-address  vrf1 
10.10.1.1

Forwards UDP broadcasts, including DHCP.

  • The value of the address argument can be a specific DHCP server address or a network address (if other DHCP servers are on the destination network segment). Using the network address enables other servers to respond to DHCP requests.

  • For multiple servers, configure one helper address for each server.

Step 5

commit

Configuring DHCPv6 Relay Binding Database Write to System Persistent Memory

Perform this task to configure the DHCPv6 relay binding database write to the system persistent memory. This helps to recover the DHCPv6 relay binding table after a system reload. The file names used for a full persistent file write are dhcpv6_srpb_{nodeid}_odd and dhcpv6_srpb_{nodeid}_even . The nodeid is the actual node ID of the node where the file is written. The incremental file is named the same way as the full file, with a _inc appended to it.


Note


With IOS XR Release 6.6.3, DHCPv6 client binding record format written to system persistent memory is changed. Due to this, when you upgrade IOS XR Software from versions lower to 6.6.3 to version 6.6.3 or above, the DHCPv6 process fails to restore the client bindings from the system persistent memory during router reload, and the router losses all the client bindings.


SUMMARY STEPS

  1. configure
  2. dhcp ipv6
  3. database [relay ] [ full-write-interval full-write-interval ] [incremental-write-interval incremental-write-interval ]
  4. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Example:


RP/0/RSP0/CPU0:router# configure

Enters global configuration mode.

Step 2

dhcp ipv6

Example:


RP/0/RSP0/CPU0:router(config)# dhcp ipv6 

Configures DHCP for IPv6 and enters the DHCPv6 configuration mode.

Step 3

database [relay ] [ full-write-interval full-write-interval ] [incremental-write-interval incremental-write-interval ]

Example:


RP/0/RSP0/CPU0:router(config-dhcpv6)# database relay full-write-interval 20 incremental-write-interval 10

Configures the DHCPv6 relay binding table write to the system persistent memory and specifies the time interval at which the full write and incremental file write are to be performed. The range, in minutes, for full-write-interval and incremental-write-interval is from 0 to 1440. The default value is 10 for full-write-interval and 1 for incremental-write-interval .

The DHCP mode should be set as relay .

Step 4

commit

Configuring DHCPv6 relay binding database write to system persistent memory: Example


 configure
 dhcp ipv6
 database relay full-write-interval 15 incremental-write-interval 5
 !
end

DHCPv4 Server

DHCP server accepts address assignment requests and renewals and assigns the IP addresses from predefined groups of addresses contained within Distributed Address Pools (DAPS). DHCP server can also be configured to supply additional information to the requesting client such as subnet mask, domain-name, the IP address of the DNS server, the default router, and other configuration parameters. DHCP server can accept broadcasts from locally attached LAN segments or from DHCP requests that have been forwarded by other DHCP relay agents within the network.

The DHCP proxy performs all the functions of a relay and also provides some additional functions. The DHCP proxy conceals DHCP server details from DHCP clients. The DHCP proxy modifies the DHCP replies such that the client considers the proxy to be the server. In this state, the client interacts with the proxy as if it is the DHCP server.

DHCP IPv4 service based mode selection

As part of DHCP IPv4 service based mode selection feature, a new mode called DHCP base is introduced. If an interface is configured in the DHCP base mode, then the DHCP selects either the DHCP proxy or the DHCP server mode to process the client request by matching option 60 (class-identifier) value of the client request with the configured value under the DHCP base profile.

For example:
 
dhcp ipv4
profile DHCP_BASE base
  match option 60 41424344 profile DHCP_PROXY proxy
  match option 60 41424355 profile DHCP_SERVER server
  default profile DEFAULT_PROFILE server
  relay information authenticate inserted
   !
profile DHCP_PROXY proxy
  helper-address vrf default 10.10.10.1 giaddr 0.0.0.0
!
profile DHCP_SERVER server
  lease 1 0 0
  pool IP_POOL
!
profile DEFAULT_PROFILE server
  lease 1 0 0
  pool IP_POOL
!
!
interface gigabitEthernet 0/0/0/0 base profile DHCP_BASE

The pool is configured under server-profile-mode and server-profile-class-sub-mode. The class-based pool selection is always given priority over profile pool selection.

The DHCPv4 server profile class sub-mode supports configuring DHCP options except few (0, 12, 50, 52, 53, 54, 58, 59, 61, 82, and 255 ).

Configuring DHCPv4 Server Profile

Perform this task to configure the DHCPv4 Server.

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. profile profile-name server
  4. bootfile boot-file-name
  5. broadcast-flag policy unicast-always
  6. class class-name
  7. exit
  8. default-router address1 address2 ... address8
  9. lease { infinite | days minutes seconds }
  10. limit lease { per-circuit-id | per-interface| per-remote-id } value
  11. netbios-name server address1 address2 ... address8
  12. netbios-node-type { number | b-node| h-node | m-node | p-node }
  13. option option-code { ascii string | hex string | ip address}
  14. pool pool-name
  15. requested-ip-address-check disable
  16. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:



RP/0/RSP0/CPU0:router(config) # dhcp ipv4
RP/0/RSP0/CPU0:router(config-dhcpv4)# 

Enables DHCP for IPv4 and enters DHCP IPv4 configuration mode.

Step 3

profile profile-name server

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4 )# profile TEST server
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# 

Enters the server profile configuration mode.

Step 4

bootfile boot-file-name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# bootfile b1

Configures the boot file.

Step 5

broadcast-flag policy unicast-always

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# broadcast-flag policy unicast-always

Configures the broadcast-flag policy to unicast-always.

Step 6

class class-name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# class Class_A
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile-class)

Creates and enters server profile class configuration submode.

Step 7

exit

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile-class)# exit
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# 

Exits the server profile class submode.

Step 8

default-router address1 address2 ... address8

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# default-router 10.20.1.2

Configures the name of the default-router or the IP address.

Step 9

lease { infinite | days minutes seconds }

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# lease infinite

Configures the lease for an IP address assigned from the pool.

Step 10

limit lease { per-circuit-id | per-interface| per-remote-id } value

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# limit lease per-circuit-id 23

Configures the limit on a lease per-circuit-id, per-interface, or per-remote-id.

Step 11

netbios-name server address1 address2 ... address8

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# netbios-name-server 10.20.3.5

Configures the NetBIOS name servers.

Step 12

netbios-node-type { number | b-node| h-node | m-node | p-node }

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# netbios-node-type p-node

Configures the type of NetBIOS node.

Step 13

option option-code { ascii string | hex string | ip address}

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# option 23 ip 10.20.34.56

Configures the DHCP option code.

Step 14

pool pool-name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# pool pool1

Configures the Distributed Address Pool Service (DAPS) pool name.

Step 15

requested-ip-address-check disable

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# requested-ip-address-check disable

Validates a requested IP address.

Step 16

commit

Configuring Multiple Classes with a Pool

Perform this task to configure multiple classes with a pool.

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. profile profile-name server
  4. pool pool-name
  5. class class-name
  6. pool pool_name
  7. match option option [ sub-option sub-option] [ ascii asciiString | hex hexString ]
  8. exit
  9. class class-name
  10. pool pool_name
  11. match vrf vrf-name
  12. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:



RP/0/RSP0/CPU0:router(config) # dhcp ipv4
RP/0/RSP0/CPU0:router(config-dhcpv4)# 

Enables DHCP for IPv4 and enters DHCP IPv4 configuration mode.

Step 3

profile profile-name server

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4 )# profile TEST server
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# 

Enters the server profile configuration mode.

Step 4

pool pool-name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# pool POOL_TEST
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)#

Configures the Distributed Address Pool Service(DAPS) pool name.

Step 5

class class-name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# class Class_A
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

Creates and enters the server profile class.

Step 6

pool pool_name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# pool pool_A
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

Configures the pool name.

Step 7

match option option [ sub-option sub-option] [ ascii asciiString | hex hexString ]

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# match option 60 hex abcd
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

The DHCP server selects a pool from a class by matching options in the received DISCOVER packet with the match option. If none of the classes match, then pools configured under the profile mode are selected. The DHCP server requests DAPS to allocate an address from that pool.

Step 8

exit

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# exit
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)#

Exits the server profile class submode.

Step 9

class class-name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# class Class_B
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

Creates and enters the server profile class.

Step 10

pool pool_name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# pool pool_B
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

Configures the pool name.

Step 11

match vrf vrf-name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# match vrf VRF1
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

The DHCP server selects a pool from a class by matching the options in the received DISCOVER packet with the match command. If none of the classes match, then pools configured under the profile mode are selected. The DHCP server requests DAPS to allocate an address from that pool.

Step 12

commit

Configuring a server profile DAPS with class match option

Perform this task to configure a server profile DAPS with class match option.

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. profile profile-name server
  4. pool pool-name
  5. class class-name
  6. poolpool_name
  7. match option option [ sub-option sub-option] [ ascii asciiString | hex hexString ]
  8. exit
  9. exit
  10. profile profile-name server
  11. dns-server address1 address2 ... address8
  12. pool pool_name
  13. class class-name
  14. poolpool_name
  15. match option option [ sub-option sub-option] [ ascii asciiString | hex hexString ]
  16. exit
  17. exit
  18. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:



RP/0/RSP0/CPU0:router(config) # dhcp ipv4
RP/0/RSP0/CPU0:router(config-dhcpv4)# 

Enables DHCP for IPv4 and enters DHCP IPv4 configuration mode.

Step 3

profile profile-name server

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4 )# profile ISP1 server
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# 

Enters the server profile configuration mode.

Step 4

pool pool-name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# pool ISP1_POOL
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)#

Configures the Distributed Address Pool Service(DAPS) pool name.

Step 5

class class-name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# class ISP1_CLASS
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

Creates and enters the server profile class.

Step 6

poolpool_name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# pool ISP1_CLASS_POOL
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

Configures the pool name.

Step 7

match option option [ sub-option sub-option] [ ascii asciiString | hex hexString ]

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# match option 60 hex PXEClient_1
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

The DHCP server selects a pool from a class by matching the options in the received DISCOVER packet with the match option. If none of the classes match, then pools configured under the profile mode will be selected. The DHCP server requests the DAPS to allocate an address from that pool.

Step 8

exit

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# exit
RP/0/RSP0/CPU0:router(config-dhcpv4-server-prfile)#

Exits the server profile class sub mode.

Step 9

exit

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# exit
RP/0/RSP0/CPU0:router(config-dhcpv4)#

Exits the server profile sub mode.

Step 10

profile profile-name server

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4 )# profile ISP2 server
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# 

Enters the server profile configuration mode.

Step 11

dns-server address1 address2 ... address8

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# dns-server 10.20.3.4
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

Configures the name of the DNS server or the IP address

Step 12

pool pool_name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# pool ISP2_POOL
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

Configures the pool name.

Step 13

class class-name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# class ISP2_CLASS
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

Creates and enters the server profile class.

Step 14

poolpool_name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# pool ISP2_CLASS_POOL
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

Configures the pool name.

Step 15

match option option [ sub-option sub-option] [ ascii asciiString | hex hexString ]

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# match option 60 hex PXEClient_2
RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)#

The DHCP server selects a pool from a class by matching the options in the received DISCOVER packet with the match option. If none of the classes match, then pools configured under the profile mode will be selected. The DHCP server requests the DAPS to allocate an address from that pool.

Step 16

exit

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-class)# exit
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)#

Exits the server profile class sub mode.

Step 17

exit

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# exit
RP/0/RSP0/CPU0:router(config-dhcpv4)#

Exits the server profile sub mode.

Step 18

commit

Configuring Server Profile without daps pool match option

Perform this task to configure a server profile without daps pool match option.

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. profile profile-name server
  4. dns-server address1 address2 ... address8
  5. exit
  6. profile profile-name server
  7. dns-server address1 address2 ... address8
  8. exit
  9. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:



RP/0/RSP0/CPU0:router(config) # dhcp ipv4
RP/0/RSP0/CPU0:router(config-dhcpv4)# 

Enables DHCP for IPv4 and enters DHCP IPv4 configuration mode.

Step 3

profile profile-name server

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4 )# profile ISP1 server
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# 

Enters the server profile configuration mode.

Step 4

dns-server address1 address2 ... address8

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# dns-server ISP1.com
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)#

Configures the name of the DNS server or IP address.

Step 5

exit

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# exit
RP/0/RSP0/CPU0:router(config-dhcpv4)#

Exits the server profile sub mode.

Step 6

profile profile-name server

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4 )# profile ISP2 server
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# 

Enters the server profile configuration mode.

Step 7

dns-server address1 address2 ... address8

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# dns-server ISP2.com
RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)#

Configures the name of the DNS server or IP address.

Step 8

exit

Example:



RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# exit
RP/0/RSP0/CPU0:router(config-dhcpv4)#

Exits the server profile sub mode.

Step 9

commit

Configuring an address pool for each ISP on DAPS

Perform this task to configure an address pool for each ISP on Distributed Address Pool Service(DAPS).

SUMMARY STEPS

  1. configure
  2. pool vrf [ all | vrf-name] { ipv4 | ipv6 } pool-name
  3. network address
  4. exit
  5. pool vrf [ all | vrf-name] { ipv4 | ipv6 } pool-name
  6. network address
  7. exit
  8. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

pool vrf [ all | vrf-name] { ipv4 | ipv6 } pool-name

Example:



RP/0/RSP0/CPU0:router(config) # pool vrf ISP_1 ipv4 ISP1_POOL
RP/0/RSP0/CPU0:router(config-pool-ipv4)# 

Configures an IPv4 pool for the specifed VRF or all vrfs.

Step 3

network address

Example:



RP/0/RSP0/CPU0:router(config-pool-ipv4)# network 10.10.10.0 
RP/0/RSP0/CPU0:router(config-pool-ipv4)# 

Specifies network for allocation.

Step 4

exit

Example:



RP/0/RSP0/CPU0:router(config-pool-ipv4)# exit
RP/0/RSP0/CPU0:router(config)#

Exits the pool ipv4 configuration submode.

Step 5

pool vrf [ all | vrf-name] { ipv4 | ipv6 } pool-name

Example:



RP/0/RSP0/CPU0:router(config) # pool vrf ISP_2 ipv4 ISP2_POOL
RP/0/RSP0/CPU0:router(config-pool-ipv4)# 

Configures an IPv4 pool for the specifed VRF or all vrfs.

Step 6

network address

Example:



RP/0/RSP0/CPU0:router(config-pool-ipv4)# network 20.20.20.0  
RP/0/RSP0/CPU0:router(config-pool-ipv4)# 

Specifies network for allocation.

Step 7

exit

Example:



RP/0/RSP0/CPU0:router(config-pool-ipv4)# exit
RP/0/RSP0/CPU0:router(config)#

Exits the pool ipv4 configuration submode.

Step 8

commit

DHCPv4 Client

The Dynamic Host Configuration Protocol (DHCP) client functionality enables the router interfaces to dynamically acquire the IPv4 address using DHCP.

The DHCP provides configuration parameters to Internet hosts. DHCP consists of two components:
  • a protocol to deliver host-specific configuration parameters from a DHCP server to a host.
  • a mechanism to allocate network addresses to hosts.

DHCP is built on a client-server model, where designated DHCP server hosts allocate network addresses, and deliver configuration parameters to dynamically configured hosts.

A relay agent is required if the client and server are not on the same Layer 2 network. The relay agent usually runs on the router, and is required because the client device does not know its own IP address initially. The agent sends out a Layer 2 broadcast to find a server that has this information. The router relays these broadcasts to the DHCP server, and forwards the responses back to the correct Layer 2 address so that the correct device gets the correct configuration information.

DHCP has the ability to allocate IP addresses only for a configurable period of time, called the lease period. If the client is required to retain this IP address for a longer period beyond the lease period, the lease period must be renewed before the IP address expires. The client renews the lease based on configuration that was sent from the server. The client unicasts a REQUEST message using the IP address of the server. When a server receives the REQUEST message and responds with an ACK message. The lease period of the client is extended by the lease time configured in the ACK message.

Restrictions and Limitations

  • DHCP client can be enabled only on management interfaces.
  • Either DHCP or static IP can be configured on an interface.

Enabling DHCP Client on an Interface

The DHCPv4 or DHCPv6 client can be enabled at an interface level. The DHCP component receives a notification when DHCPv4 or DHCPv6 is enabled or disabled on an interface.

Router# configure
Router(config)# interface MgmtEth rack/slot/CPU0/port
Router(config)# interface interface_name ipv6 address dhcp  

DHCPv6 Relay Agent Notification for Prefix Delegation

DHCPv6 relay agent notification for prefix delegation allows the router working as a DHCPv6 relay agent to find prefix delegation options by reviewing the contents of a DHCPv6 RELAY-REPLY packet that is being relayed by the relay agent to the client. When the relay agent finds the prefix delegation option, the relay agent extracts the information about the prefix being delegated and inserts an IPv6 subscriber route matching the prefix delegation information onto the relay agent. Future packets destined to that prefix via relay are forwarded based on the information contained in the prefix delegation. The IPv6 subscriber route remains in the routing table until the prefix delegation lease time expires or the relay agent receives a release packet from the client releasing the prefix delegation.

The relay agent automatically does the subscriber route management.

The IPv6 routes are added when the relay agent relays a RELAY-REPLY packet, and the IPv6 routes are deleted when the prefix delegation lease time expires or the relay agent receives a release message. An IPv6 subscriber route in the routing table of the relay agent can be updated when the prefix delegation lease time is extended.

This feature leaves an IPv6 route on the routing table of the relay agent. This registered IPv6 address allows unicast reverse packet forwarding (uRPF) to work by allowing the router doing the reverse lookup to confirm that the IPv6 address on the relay agent is not malformed or spoofed. The IPv6 route in the routing table of the relay agent can be redistributed to other routing protocols to advertise the subnets to other nodes. When the client sends a DHCP_DECLINE message, the routes are removed.

Configuring DHCPv6 Stateful Relay Agent for Prefix Delegation

Perform this task to configure Dynamic Host Configuration Protocol (DHCP) IPv6 relay agent notification for prefix delegation.

SUMMARY STEPS

  1. configure
  2. dhcp ipv6
  3. profile profile-name proxy
  4. helper-address ipv6-address interface type interface-path-id
  5. exit
  6. interface type interface-path-id proxy
  7. profile profile-name
  8. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv6

Example:



RP/0/RSP0/CPU0:router(config) # dhcp ipv6
RP/0/RSP0/CPU0:router(config-dhcpv6)# 

Enables DHCP for IPv6 and enters DHCP IPv6 configuration mode.

Step 3

profile profile-name proxy

Example:



RP/0/RSP0/CPU0:router(config-dhcpv6)# profile downstream proxy
RP/0/RSP0/CPU0:router(config-dhcpv6-profile)# 

Enters the proxy profile configuration mode.

Step 4

helper-address ipv6-address interface type interface-path-id

Example:



RP/0/RSP0/CPU0:router(config-dhcpv6-profile)# helper-address 2001:db8::1 GigabitEthernet 0/1/0/1
RP/0/RSP0/CPU0:router(config-dhcpv6-profile)

Configure the DHCP IPv6 relay agent.

Step 5

exit

Example:



RP/0/RSP0/CPU0:router(config-dhcpv6-profile)# exit
RP/0/RSP0/CPU0:router(config-dhcpv6)# 

Exits from the profile configuration mode.

Step 6

interface type interface-path-id proxy

Example:



RP/0/RSP0/CPU0:router(config-dhcpv6)# interface GigabitEthernet 0/1/0/0 proxy
RP/0/RSP0/CPU0:router(config-dhcpv6-if)# 

Enables IPv6 DHCP on an interface and acts as an IPv6 DHCP stateful relay agent.

Step 7

profile profile-name

Example:



RP/0/RSP0/CPU0:router(config-dhcpv6-if)# profile downstream
RP/0/RSP0/CPU0:router(config-dhcpv6-if)# 

Enters the profile configuration mode.

Step 8

commit

Enabling Secure ARP

Secure ARP is disabled by default; this task describes how to enable secure ARP.

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. Do one of the following:
    • profile profile-name proxy
    • profile profile-name server
  4. secure-arp
  5. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:


RP/0/RSP0/CPU0:router(config)# dhcp ipv4

Enters DHCP IPv4 configuration mode.

Step 3

Do one of the following:

  • profile profile-name proxy
  • profile profile-name server

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4)# profile profile1 server

Enters DHCP IPv4 profile proxy or server submode.

Step 4

secure-arp

Example:


RP/0/RSP0/CPU0:router(config-dhcpv4-server-profile)# secure-arp

Enables secure ARP.

Step 5

commit

Configuration Examples for the DHCP Relay Agent

This section provides the following configuration examples:

DHCP Relay Profile: Example

The following example shows how to configure the Cisco IOS XR relay profile:


dhcp ipv4 
 profile client relay
  helper-address vrf foo 10.10.1.1
 !        
! ...

DHCP Relay on an Interface: Example

The following example shows how to enable the DHCP relay agent on an interface:


dhcp ipv4
 interface GigabitEthernet 0/1/1/0 relay profile client
!

DHCP Relay on a VRF: Example

The following example shows how to enable the DHCP relay agent on a VRF:


dhcp ipv4
 vrf default relay profile client
!

Relay Agent Information Option Support: Example

The following example shows how to enable the relay agent and the insertion and removal of the DHCP relay information option:


dhcp ipv4
 profile client relay
relay information option

 !
!

Relay Agent Giaddr Policy: Example

The following example shows how to configure relay agent giaddr policy:


dhcp ipv4
 profile client relay
  giaddr policy drop
 !
!

Implementing DHCP Snooping

Prerequisites for Configuring DHCP Snooping

The following prerequisites are required example shows how to configure DHCP IPv4 snooping relay agent broadcast flag policy:

  • You must be in a user group associated with a task group that includes the proper task IDs. The command reference guides include the task IDs required for each command. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

  • A Cisco ASR 9000 Series Router running Cisco IOS XR software.

  • A configured and running DHCP client and DHCP server.

Information about DHCP Snooping

DHCP Snooping features are focused on the edge of the aggregation network. Security features are applied at the first point of entry for subscribers. Relay agent information option information is used to identify the subscriber’s line, which is either the DSL line to the subscriber’s home or the first port in the aggregation network.

The central concept for DHCP snooping is that of trusted and untrusted links. A trusted link is one providing secure access for traffic on that link. On an untrusted link, subscriber identity and subscriber traffic cannot be determined. DHCP snooping runs on untrusted links to provide subscriber identity. DHCP Snooping in an Aggregation Network shows an aggregation network. The link from the DSLAM to the aggregation network is untrusted and is the point of presence for DHCP snooping. The links connecting the switches in the aggregation network and the link from the aggregation network to the intelligent edge is considered trusted.


Note


Enabling both DHCP relay on a BVI and DHCP snooping in a bridge domain that has a BVI can result in duplicate DHCP messages from the DHCP client to the DHCP server.


Figure 2. DHCP Snooping in an Aggregation Network

Trusted and Untrusted Ports

On trusted ports, DHCP BOOTREQUEST packets are forwarded by DHCP snooping. The client’s address lease is not tracked and the client is not bound to the port. DHCP BOOTREPLY packets are forwarded.

When the first DHCP BOOTREQUEST packet from a client is received on an untrusted port, DHCP snooping binds the client to the bridge port and tracks the clients’s address lease. When that address lease expires, the client is deleted from the database and is unbound from the bridge port. Packets from this client received on this bridge port are processed and forwarded as long as the binding exists. Packets that are received on another bridge port from this client are dropped while the binding exists. DHCP snooping only forwards DHCP BOOTREPLY packets for this client on the bridge port that the client is bound to. DHCP BOOTREPLY packets that are received on untrusted ports are not forwarded.

DHCP Snooping in a Bridge Domain

To enable DHCP snooping in a bridge domain, there must be at least two profiles, a trusted profile and an untrusted profile. The untrusted profile is assigned to the client-facing ports, and the trusted profile is assigned to the server-facing ports. In most cases, there are many client facing ports and few server-facing ports. The simplest example is two ports, a client-facing port and a server-facing port, with an untrusted profile explicitly assigned to the client-facing port and a trusted profile assigned to the server-facing port.

Assigning Profiles to a Bridge Domain

Because there are normally many client-facing ports and a small number of server-facing ports, the operator assigns the untrusted profile to the bridge domain. This configuration effectively assigns an untrusted profile to every port in the bridge domain. This action saves the operator from explicitly assigning the untrusted profile to all of the client-facing ports. Because there also must be server-facing ports that have trusted DHCP snooping profiles, in order for DHCP snooping to function properly, this untrusted DHCP snooping profile assignment is overridden to server-facing ports by specifically configuring trusted DHCP snooping profiles on the server-facing ports. For ports in the bridge domain that do not require DHCP snooping, all should have the none profile assigned to them to disable DHCP snooping on those ports.

Relay Information Options

You can configure a DHCP snooping profile to insert the relay information option (option 82) into DHCP client packets only when it is assigned to a client port. The relay information option allow-untrusted command addresses what to do with DHCP client packets when there is a null giaddr and a relay-information option already in the client packet when it is received. This is a different condition than a DHCP snooping trusted/untrusted port. The relay information option allow-untrusted command determines how the DHCP snooping application handles untrusted relay information options.

How to Configure DHCP Snooping

This section contains the following tasks:

Enabling DHCP Snooping in a Bridge Domain

The following configuration creates two ports, a client-facing port and a server-facing port. In Step 1 through Step 8, an untrusted DHCP snooping profile is assigned to the client bridge port and trusted DHCP snooping profile is assigned to the server bridge port. In Step 9 through Step 18, an untrusted DHCP snooping profile is assigned to the bridge domain and trusted DHCP snooping profiles are assigned to server bridge ports.

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. profile untrusted-profile-name snoop
  4. exit
  5. dhcp ipv4
  6. profile profile-name snoop
  7. trusted
  8. exit
  9. l2vpn
  10. bridge group group-name
  11. bridge-domain bridge-domain-name
  12. interface type interface-path-id
  13. dhcp ipv4 snoop profile untrusted-profile-name
  14. interface type interface-path-id
  15. dhcp ipv4 snoop profile trusted-profile-name
  16. exit
  17. exit
  18. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:

RP/0/RSP0/CPU0:router(config)# dhcp ipv4

Enters DHCP IPv4 profile configuration submode.

Step 3

profile untrusted-profile-name snoop

Example:

RP/0/RSP0/CPU0:router(config-dhcpv4)# profile untrustedClientProfile snoop

Configures an untrusted DHCP snooping profile for the client port.

Step 4

exit

Example:

RP/0/RSP0/CPU0:router(config-dhcpv4)# exit

Exits DHCP IPv4 profile configuration mode.

Step 5

dhcp ipv4

Example:

RP/0/RSP0/CPU0:router(config)# dhcp ipv4

Enables DHCP for IPv4 and enters DHCP IPv4 profile configuration mode.

Step 6

profile profile-name snoop

Example:

RP/0/RSP0/CPU0:router(config-dhcpv4)# profile trustedServerProfile snoop

Configures a trusted DHCP snooping profile for the server port.

Step 7

trusted

Example:

RP/0/RSP0/CPU0:router(config-dhcv4)# trusted

Configures a DHCP snoop profile to be trusted.

Step 8

exit

Example:

RP/0/RSP0/CPU0:router(config-dhcv4)# exit

Exits DHCP IPv4 profile configuration mode.

Step 9

l2vpn

Example:

RP/0/RSP0/CPU0:router(config)# l2vpn

Enters l2vpn configuration mode.

Step 10

bridge group group-name

Example:

RP/0/RSP0/CPU0:router(config-l2vpn)# bridge group ccc

Creates a bridge group to contain bridge domains and enters l2vpn bridge group configuration submode.

Step 11

bridge-domain bridge-domain-name

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg)# bridge-domain ddd

Establishes a bridge domain.

Step 12

interface type interface-path-id

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# interface gigabitethernet 0/1/0/0

Identifies an interface.

Step 13

dhcp ipv4 snoop profile untrusted-profile-name

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd-ac)# dhcp ipv4 snoop profile untrustedClientProfile

Attaches an untrusted DHCP snoop profile to the bridge port.

Step 14

interface type interface-path-id

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd-ac)# gigabitethernet 0/1/0/1

Identifies an interface.

Step 15

dhcp ipv4 snoop profile trusted-profile-name

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd-ac)# dhcp ipv4 snoop profile trustedServerProfile

Attaches a trusted DHCP snoop profile to the bridge port.

Step 16

exit

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd-ac)# exit

Exits the l2vpn bridge group bridge-domain interface configuration submode.

Step 17

exit

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# exit

Exits the l2vpn bridge group bridge-domain configuration submode.

Step 18

commit

Disabling DHCP Snooping on a Specific Bridge Port

The following configuration enables DHCP to snoop packets on all bridge ports in the bridge domain ISP1 except for bridge port GigabitEthernet 0/1/0/1 and GigabitEthernet 0/1/0/2. DHCP snooping is disabled on bridge port GigabitEthernet 0/1/0/1. Bridge port GigabitEthernet 0/1/0/2 is the trusted port that connects to the server. In this example, no additional features are enabled, so only DHCP snooping is running.

SUMMARY STEPS

  1. configure
  2. l2vpn
  3. bridge group group-name
  4. bridge-domain bridge-domain-name
  5. dhcp ipv4 snoop profile profile-name
  6. interface type interface-path-id
  7. dhcp ipv4 none
  8. interface type interface-path-id
  9. dhcp ipv4 snoop profile profile-name
  10. exit
  11. exit
  12. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

l2vpn

Example:

RP/0/RSP0/CPU0:router(config)# l2vpn

Enters l2vpn configuration submode.

Step 3

bridge group group-name

Example:

RP/0/RSP0/CPU0:router(config-l2vpn)# bridge group GRP1

Creates a bridge group to contain bridge domains and enters l2vpn bridge group configuration submode.

Step 4

bridge-domain bridge-domain-name

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg)# bridge-domain ISP1

Establishes a bridge domain and enters l2vpn bridge group bridge-domain configuration submode.

Step 5

dhcp ipv4 snoop profile profile-name

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# dhcp ipv4 snoop profile untrustedClientProfile

Attaches the untrusted DHCP snooping profile to the bridge domain.

Step 6

interface type interface-path-id

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# interface gigabitethernet 0/1/0/1

Identifies an interface and enters l2vpn bridge group bridge-domain interface configuration submode.

Step 7

dhcp ipv4 none

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd-if)# dhcp ipv4 none

Disables DHCP snooping on the port.

Step 8

interface type interface-path-id

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# interface gigabitethernet 0/1/0/2

Identifies an interface and enters l2vpn bridge group bridge-domain interface configuration submode.

Step 9

dhcp ipv4 snoop profile profile-name

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# dhcp ipv4 snoop profile trustedServerProfile

Attaches the trusted DHCP snooping profile to a port.

Step 10

exit

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bd-bg)# exit

Exits l2vpn bridge-domain bridge group interface configuration submode.

Step 11

exit

Example:

RP/0/RSP0/CPU0:router(config-l2vpn-bg)# exit

Exits l2vpn bridge-domain submode.

Step 12

commit

Using the Relay Information Option

This task shows how to use the relay information commands to insert the relay information option (option 82) into DHCP client packets and forward DHCP packets with untrusted relay information options.

SUMMARY STEPS

  1. configure
  2. dhcp ipv4
  3. profile profile-name snoop
  4. relay information option
  5. relay information option allow-untrusted
  6. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Step 2

dhcp ipv4

Example:

RP/0/RSP0/CPU0:router(config)# dhcp ipv4

Enters DHCP IPv4 profile configuration submode.

Step 3

profile profile-name snoop

Example:

RP/0/RSP0/CPU0:router(config-dhcpv4)# profile untrustedClientProfile snoop

Configures an untrusted DHCP snooping profile for the client port.

Step 4

relay information option

Example:

RP/0/RSP0/CPU0:router(config-dhcpv4-snoop-profile)# relay information option

Enables the system to insert the DHCP relay information option field in forwarded BOOTREQUEST messages to a DHCP server.

Step 5

relay information option allow-untrusted

Example:

RP/0/RSP0/CPU0:router(config-dhcpv4-snoop-profile)# relay information option allow-untrusted

Configures DHCP IPv4 relay not to discard BOOTREQUEST packets that have an existing relay information option and the giaddr set to zero.

Step 6

commit

Configuration Examples for DHCP Snooping

This section provides the following configuration examples:

Assigning a DHCP Profile to a Bridge Domain: Example

The following example shows how to enable DHCP snooping in a bridge domain:


l2vpn
 bridge group GRP1
  bridge-domain ISP1
   dhcp ipv4 profile untrustedClientProfile snoop

Disabling DHCP Snooping on a Specific Bridge Port: Example

The following example shows how to disable DHCP snooping on a specific bridge port:


interface gigabitethernet 0/1/0/1
 dhcp ipv4 none

Configuring a DHCP Profile for Trusted Bridge Ports: Example

The following example shows how to configure a DHCP profile for trusted bridge ports:


dhcp ipv4 profile trustedServerProfile snoop
 trusted

Configuring an Untrusted Profile on a Bridge Domain: Example

The following example shows how to attach a profile to a bridge domain and disable snooping on a bridge port.


l2vpn
 bridge group GRP1
  bridge-domain ISP1
   dhcp ipv4 profile untrustedClientProfile snoop
    interface gigabitethernet 0/1/0/1
     dhcp ipv4 none

Configuring a Trusted Bridge Port: Example

The following example shows ow to assign a trusted DHCP snooping profile to a bridge port:


l2vpn
 bridge group GRP1
  bridge-domain ISP1
   interface gigabitethernet 0/1/0/2
    dhcp ipv4 profile trustedServerProfile snoop

DHCPv6 Proxy Binding Table Reload Persistency

The Cisco IOS-XR Dynamic Host Configuration Protocol (DHCP) application is responsible for maintaining the DHCP binding state for the DHCP leases allocated to clients by the DHCP application. These binding states are learned by the DHCP application (proxy/relay/snooping). DHCP clients expect to maintain a DHCP lease regardless of the events that occur to the DHCP application.


Note


From Release 6.2.2 onwards, 200K sessions are supported on a proxy or server running DHCPv6.


This feature enables the DHCP application to maintain bind state through the above events:
  • Process restart – Local checkpoint

  • RP failover – Hot standby RP through checkpoint

  • LC IMDR – Local checkpoint

  • LC OIR – Shadow table on RP

  • System restart – Bindings saved on local disk

Configuring DHCPv6 Proxy Binding Database Write to System Persistent Memory

Perform this task to configure the DHCPv6 binding database write to the system persistent memory. This helps to recover the DHCPv6 binding table after a system reload. The file names used for a full persistent file write are dhcpv6_srpb_{nodeid}_odd and dhcpv6_srpb_{nodeid}_even . The nodeid is the actual node ID of the node where the file is written. The incremental file is named the same way as the full file, with a _inc appended to it.


Note


From Release 6.2.2 onwards, 200K sessions are supported on a proxy or server running DHCPv6.


SUMMARY STEPS

  1. configure
  2. dhcp ipv6
  3. database [proxy ] [ full-write-interval full-write-interval ] [incremental-write-interval incremental-write-interval ]
  4. commit

DETAILED STEPS

  Command or Action Purpose

Step 1

configure

Example:


RP/0/RSP0/CPU0:router# configure

Enters global configuration mode.

Step 2

dhcp ipv6

Example:


RP/0/RSP0/CPU0:router(config)# dhcp ipv6 

Configures DHCP for IPv6 and enters the DHCPv6 configuration mode.

Step 3

database [proxy ] [ full-write-interval full-write-interval ] [incremental-write-interval incremental-write-interval ]

Example:


RP/0/RSP0/CPU0:router(config-dhcpv6)# database proxy full-write-interval 20 incremental-write-interval 10

Configures the DHCPv6 binding table write to the system persistent memory and specifies the time interval at which the full write and incremental file write are to be performed. The range, in minutes, for full-write-interval and incremental-write-interval is from 0 to 1440. The default value is 10 for full-write-interval and 1 for incremental-write-interval .

The DHCP mode should be set as proxy .

Step 4

commit

Configuring DHCP binding database write to system persistent memory: Example


 configure
 dhcp ipv6
 database proxy full-write-interval 15 incremental-write-interval 5
 !
end

DHCP Session MAC Throttle

The ASR9K router supports the DHCP session MAC throttle feature. This feature limits the number of DHCP client requests reaching the ASR9K, based on the MAC address of the DHCP clients. This feature is supported for the DHCPv4 proxy, the DHCPv4 server, and the DHCPV6 proxy. The feature prevents a DHCP client from sending multiple DISCOVER packets to the ASR9K router, within short periods of time. This, in turn, prevents that client from impacting the session establishment of other DHCP clients.


Note


From Release 6.2.2 onwards, 200K sessions are supported on a proxy or server running DHCPv6.


A unique throttle entry is created in the system for each unique MAC address received on any interface where the profile is attached.

To configure the DHCP session MAC throttle feature, use the sessions mac throttle command in the respective DHCP profile configuration mode.

Configuring DHCP Session MAC Throttle: Example



dhcp ipv4
 profile p1 server
  sessions mac throttle 300 60 40
 !
 interface GigabitEthernet0/0/0/0 server profile p1
!

Additional References

The following sections provide references related to implementing the Cisco IOS XR DHCP relay agent and DHCP snooping features.

Related Documents

Related Topic

Document Title

Cisco IOS XR

DHCP commands

DHCP Commands module in the IP Addresses and Services Command Reference for Cisco ASR 9000 Series Routers

Getting started material

Cisco ASR 9000 Series Aggregation Services Router Getting Started Guide

Information about user groups and task IDs

Configuring AAA Services module in the System Security Configuration Guide for Cisco ASR 9000 Series Routers

Standards

Standards

Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

MIBs

MIBs

MIBs Link

To locate and download MIBs, use the Cisco MIB Locator found at the following URL and choose a platform under the Cisco Access Products menu: https://mibs.cloudapps.cisco.com/ITDIT/MIBS/servlet/index

RFCs

RFC

Title

RFC 2131

Dynamic Host Configuration Protocol

Technical Assistance

Description

Link

The Cisco Technical Support website contains thousands of pages of searchable technical content, including links to products, technologies, solutions, technical tips, and tools. Registered Cisco.com users can log in from this page to access even more content.

http://www.cisco.com/techsupport