Use the System Template to create a tracker for static routes.

1. From Cisco vManage menu, choose Configuration > Templates.

2. Click Feature Templates.

   Note	In Cisco vManage Release 20.7.x and earlier releases, Feature Templates is titled Feature.

3. Navigate to the Cisco System template for the device.

   Note	For information about creating a System template, see Create System Template.

4. Click Tracker. Click New Endpoint Tracker to configure the tracker parameters.

   Table 2. Tracker Parameters

   Field	Description
   Name	Name of the tracker. The name can be up to 128 alphanumeric characters.
   Threshold	Wait time for the probe to return a response before declaring that the configured endpoint is down. Range is from 100 to 1000 milliseconds. Default is 300 milliseconds.
   Interval	Time interval between probes to determine the status of the configured endpoint. Default is 60 seconds (1 minute). Range is from 10 to 600 seconds.
   Multiplier	Number of times probes are sent before declaring that the endpoint is down. Range is from 1 to 10. Default is 3.
   Tracker Type	From the drop-down, choose Global. From the Tracker Type field drop-down, choose Static Route. From Cisco SD-WAN Release 20.7.1, you can configure a tracker group with dual endpoints on Cisco vEdge devices and associate this tracker group to a static route.
   Endpoint Type	Choose endpoint type IP Address.
   End-Point Type: IP Address	IP address of the static route end point. This is the destination on the internet to which the router sends probes to determine the status of the route.

5. Click Add.

6. Click Save.

7. To create a tracker group, click New Endpoint Tracker.

   From the Tracker Type drop-down list, choose tracker-group and configure the tracker group parameters.

   Note	Ensure that you have created two trackers to form a tracker group.

   Table 3. Tracker Group Parameters

   Fields	Description
   Name	Name of the tracker group.
   Tracker Type	From the drop-down, choose Global. From the Tracker Type field drop-down, choose Static Route. From Cisco SD-WAN Release 20.7.1, you can configure a tracker group with dual endpoints on Cisco vEdge devices and associate this tracker group to a static route.
   Tracker Elements	This field is displayed only if you chose Tracker-group as the tracker type. Add the existing interface tracker names (separated by a space). When you add this tracker to the template, the tracker group is associated with these individual trackers, and you can then associate the tracker group to a static route.
   Tracker Boolean	From the drop-down list, choose Global. This field is displayed only if you chose tracker-group as the Tracker Type. By default, the OR option is selected. Choose AND or OR. OR ensures that the static route status is reported as active if either one of the associated trackers of the tracker group report that the route is active. If you select AND, the static route status is reported as active if both the associated trackers of the tracker group report that the route is active.

8. Click Add.

9. Click Save.

   Note	Complete all the mandatory actions before you save the template.

Use the VPN template to associate a tracker to a static route next hop.

Note	You can apply only one tracker per static route next hop.

1. From the Cisco vManage menu, choose Configuration > Templates.

2. Click Feature Templates.

   Note	In Cisco vManage Release 20.7.x and earlier releases, Feature Templates is titled Feature.

3. Navigate to the Cisco VPN Template for the device.

   Note	For information about creating a VPN template, see Create VPN Template.

4. Enter Template Name and Description as required.

5. In Basic Configuration, by default, VPN is set to 0. Set a VPN value within (1–511, 513–65530) range for service VPNs, for service-side data traffic on Cisco IOS XE SD-WAN devices.

   Note	You can configure static route tracker only on service VPNs.

6. Click IPv4 Route.

7. Click New IPv4 Route.

8. In the IPv4 Prefix field, enter a value.

9. Click Next Hop.

10. Click Add Next Hop and enter values for the fields listed in the table.

    Parameter Name	Description
    Address	Specify the next-hop IPv4 address.
    Distance	Specify the administrative distance for the route.
    Tracker	Enter the name of the gateway tracker to determine whether the next hop is reachable before adding that route to the route table of the device.
    Add Next Hop	Enter the name of the gateway tracker with the next hop address to determine whether the next hop is reachable before adding that route to the route table of the device.

11. Click Add to create the static route with the next-hop tracker.

    Note	Configuring a static route with a next-hop 'X.X.X.255' is not supported. Cisco vEdge device does not implement RFC 3021.

12. Click Save.

Note	You need to fill all the mandatory fields in the form to save the VPN template.

View Static Route Tracker

To view information about a static tracker on a transport interface:

1. From the Cisco vManage menu, choose Monitor > Devices.

   Cisco vManage Release 20.6.x and earlier: From the Cisco vManage menu, choose Monitor > Network.

2. Choose a device from the list of devices.

3. Click Real Time.

4. From the Device Options drop-down list, choose Static Route Tracker Info.