M Commands
This chapter describes the Cisco Nexus 1000V commands that begin with the letter M.
mac access-list
To create a MAC ACL, use the mac access-list command. To remove the MAC ACL, use the no form of this command.
mac access-list name
no mac access-list name
Syntax Description
name |
List name. The range of valid values is 1 to 64. |
Defaults
The MAC ACL does not exist.
Command Modes
Global configuration (config)
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to create a MAC ACL:
n1000v#
configure terminal
n1000v(config)#
mac access-list aL1
n1000v(config)#
Related Commands
|
|
---|---|
show access-list |
Displays access list information. |
mac address-table aging-time
To configure the aging time for entries in the Layer 2 table, use the mac address-table aging-time command. To return to the default settings, use the no form of this command.
mac address-table aging-time seconds [vlan vlan-id]
no mac address-table aging-time [vlan vlan-id]
Syntax Description
Defaults
1800 seconds
Command Modes
Global configuration (config)
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
Enter 0 seconds to disable the aging process.
The age value may be rounded off to the nearest multiple of 5 seconds. If the system rounds the value to a different value from that specified by the user (from the rounding process), the system returns an informational message.
When you use this command in the global configuration mode, the age values of all VLANs for which a configuration has not been specified are modified and those VLANs with specifically modified aging times are not modified. When you use the no form of this command without the VLAN parameter, only those VLANs that have not been specifically configured for the aging time reset to the default value. Those VLANs with specifically modified aging times are not modified.
When you use this command and specify a VLAN, the aging time for only the specified VLAN is modified. When you use the no form of this command and specify a VLAN, the aging time for the VLAN is returned to the current global configuration for the aging time, which may or may not be the default value of 300 seconds depending if the global configuration of the device for aging time has been changed.
Aging time is counted from the last time that the switch detected the MAC address.
Examples
This example shows how to change the length of time an entry remains in the MAC address table to 500 seconds for the entire device:
n1000v(config)#
mac address-table aging-time 500
n1000v(config)#
Related Commands
|
|
---|---|
show mac address-table |
Displays information about the MAC address table. |
clear mac address-table aging-time |
Displays information about the MAC address aging time. |
mac address-table static
To configure a static entry for the Layer 2 MAC address table, use the mac address-table static command. To delete the static entry, use the no form of this command.
mac address-table static mac-address vlan vlan-id {[drop | interface {type slot/port | port-channel number]}
no mac address-table static {address mac_addr} {vlan vlan-id}
Syntax Description
Defaults
None
Command Modes
Global configuration (config)
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
You cannot apply the mac address-table static mac-address vlan vlan-id drop command to a multicast MAC address.
The output interface specified cannot be a VLAN interface or a Switched Virtual Interface (SVI).
Use the no form to remove entries that are profiled by the combination of specified entry information.
Examples
This example shows how to add a static entry to the MAC address table:
n1000v(config)#
mac address-table static 0050.3e8d.6400 vlan 3 interface ethernet 2/1
n1000v(config)#
Related Commands
|
|
---|---|
show mac address-table |
Displays information about MAC address table. |
mac port access-group
To enable access control for port groups, use the mac port access-group command. To disable access control for port groups, use the no form of this command.
mac port access-group name {in | out}
no mac port access-group name {in | out}
Syntax Description
name |
Group name. The range of valid values is 1 to 64. |
in |
Specifies inbound traffic. |
out |
Specifies outbound traffic. |
Defaults
Access control for packets is not specified.
Command Modes
Port profile configuration (config-port-prof)
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to enable access control for port groups:
n1000v# configure terminal
n1000v(config)# port-profile 1
n1000v(config-port-prof)# mac port access-group groupOne in
n1000v(config-port-prof)#
Related Commands
|
|
---|---|
show mac |
Displays MAC information. |
match (ACL)
To define ACL matching criteria, use the match command. To remove matching criteria, use the no form of this command.
match {{access-group name name} | {[not] cos cos-list} | {[not] dscp {dscp-list | dscp-enum}+} | {[not] precedence {precedence-list | prec-enum}+} | {[not] discard-class discard-class-list} | {[not] qos-group qos-group-list} | {[not] class-map cmap-name} | {[not] packet length len-list} | {[not] ip rtp port-list}}
no match {{access-group name acl-name} | {[not] cos cos-list} | {[not] dscp {dscp-list | dscp-enum}+} | {[not] precedence {precedence-list | prec-enum}+} | {[not] discard-class discard-class-list} | {[not] qos-group qos-group-list} | {[not] class-map cmap-name} | {[not] packet length len-list} | {[not] ip rtp port-list}}
Syntax Description
Defaults
None
Command Modes
Class map configuration (config-cmap-qos
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to configure a class-map match criteria:
n1000v(config)# class-map cl_map1
n1000v(config-cmap-qos)# match access-group name ac_gr1
n1000v(config-cmap-qos)#
This example shows how to remove the class-map match criteria:
n1000v(config)# class-map cl_map1
n1000v(config-cmap-qos)# no match access-group name ac_gr1
n1000v(config-cmap-qos)#
Related Commands
|
|
---|---|
show class map |
Displays class map information. |
match ip (NetFlow)
To define IP matching criteria for a NetFlow flow record, use the match ip command. To remove the matching criteria, use the no form of this command.
match ip {protocol | tos}
no match ip {protocol | tos}
Syntax Description
protocol |
Protocol. |
tos |
Type of service. |
Defaults
None
Command Modes
Flow record configuration (config-flow-record)
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to configure IP matching criteria for a NetFlow flow record and then display the result:
n1000v# config t
n1000v(config)# flow record RecordTest
n1000v(config-flow-record)# match ip protocol
n1000v(config-flow-record)# show flow record
Flow record RecordTest:
No. of users: 0
Template ID: 0
Fields:
match ip protocol
match interface input
match interface output
match flow direction
doc-n1000v(config-flow-record)#
This example shows how to remove the IP matching criteria for a NetFlow flow record a and then display the result:
n1000v# config t
n1000v(config)# flow record RecordTest
n1000v(config-flow-record)# no match ip protocol
n1000v(config-flow-record)# show flow record
Flow record RecordTest:
No. of users: 0
Template ID: 0
Fields:
match interface input
match interface output
match flow direction
doc-n1000v(config-flow-record)#
Related Commands
match ipv4 (NetFlow)
To define IPv4 matching criteria for a NetFlow flow record, use the match ipv4 command. To remove the matching criteria, use the no form of this command.
match ipv4 {source | destination} address
no match ipv4 {source | destination} address
Syntax Description
source |
Source Address. |
destination |
Destination Address. |
address |
Address. |
Defaults
None
Command Modes
Flow record configuration (config-flow-record)
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to configure IPv4 matching criteria for a NetFlow flow record and then display the result:
n1000v# config t
n1000v(config)# flow record RecordTest
n1000v(config-flow-record)# match ipv4 destination address
n1000v(config-flow-record)# show flow record
Flow record RecordTest:
Description: Ipv4flow
No. of users: 0
Template ID: 0
Fields:
match ipv4 destination address
match interface input
match interface output
match flow direction
collect counter packets
n1000v(config-flow-record)#
This example shows how to remove the IPv4 matching criteria for a NetFlow flow record a and then display the result:
n1000v# config t
n1000v(config)# flow record RecordTest
n1000v(config-flow-record)# no match ipv4 destination address
n1000v(config-flow-record)# show flow record
Flow record RecordTest:
No. of users: 0
Template ID: 0
Fields:
match interface input
match interface output
match flow direction
doc-n1000v(config-flow-record)#
Related Commands
match transport (NetFlow)
To define transport matching criteria for a NetFlow flow record, use the match transport command. To remove the matching criteria, use the no form of this command.
match transport {destination-port | source-port}
no match transport {destination-port | source-port}
Syntax Description
destination-port |
Transport destination port. |
source-port |
Transport source port. |
Defaults
None
Command Modes
Flow Record configuration (config-flow-record)
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to configure transport matching criteria for a NetFlow flow record and then display the result:
n1000v# config t
n1000v(config)# flow record RecordTest
n1000v(config-flow-record)# match transport destination-port
n1000v(config-flow-record)# show flow record
Flow record RecordTest:
Description: Ipv4flow
No. of users: 0
Template ID: 0
Fields:
match ipv4 destination-port
match interface input
match interface output
match flow direction
collect counter packets
n1000v(config-flow-record)#
This example shows how to remove the transport matching criteria for a NetFlow flow record a and then display the result:
n1000v# config t
n1000v(config)# flow record RecordTest
n1000v(config-flow-record)# no match transport destination-port
n1000v(config-flow-record)# show flow record
Flow record RecordTest:
No. of users: 0
Template ID: 0
Fields:
match interface input
match interface output
match flow direction
doc-n1000v(config-flow-record)#
Related Commands
media
To specify the media type of a VLAN as Ethernet, use the media command. To remove the type, use the no form of this command.
media ethernet
no media
Syntax Description
ethernet |
Specifies Ethernet media type. |
Defaults
None
Command Modes
VLAN configuration (config-vlan)
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to configure media type:
n1000v#
configure terminal
n1000v(
config)#
media ethernet
n1000v(
config)#
Related Commands
|
|
---|---|
show vlan |
Displays VLAN information. |
mkdir
To create a new directory, use the mkdir command.
mkdir {bootflash: | debug: | volatile:}
Syntax Description
bootflash: |
Specifies bootflash as the directory name. |
debug: |
Specifies debug as the directory name. |
volatile: |
Specifies volatile as the directory name. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to create the bootflash: directory:
n1000v#
mkdir bootflash:
Related Commands
|
|
---|---|
cd |
Changes the current working directory. |
dir |
Displays the directory contents. |
pwd |
Displays the name of the current working directory. |
module vem
To enter commands on the VEM remotely from the Cisco Nexus 1000V, use the module vem command.
module vem module-number execute line [line]
Syntax Description
module-number |
Specifies the module number. The range is 3 to 66. |
execute |
Specifies the command to execute on the VEM. |
line |
(Optional)The syntax of the command to be sent to the VEM. |
Defaults
None
Command Modes
EXEC
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the VEM port profile configuration remotely from the Cisco Nexus 1000V:
n1000v#
module vem 3 execute vemcmd show port-profile
This example shows how to display the VEM VSD configuration remotely from the Cisco Nexus 1000V:
n1000v# module vem 3 execute vemcmd show vsd
ID Def_Act ILTL OLTL NMLTL State Member LTLs
1 DROP 48 49 4 ENA 54,52,55,53
2 FRWD 50 51 0 ENA
vsim-cp# module vem 3 execute vemcmd show vsd ports
LTL IfIndex VSD_ID VSD_PORT_TYPE
48 1b020000 1 INSIDE
49 1b020010 1 OUTSIDE
50 1b020020 2 INSIDE
51 1b020030 2 OUTSIDE
52 1b020040 1 REGULAR
53 1b020050 1 REGULAR
54 1b020060 1 REGULAR
55 1b020070 1 REGULAR
n1000v#
Related Commands
|
|
---|---|
show module vem |
Displays Virtual Ethernet Module information. |
monitor session
To enter the monitor configuration mode for configuring an Ethernet switch port analyzer (SPAN) session for analyzing traffic between ports, use the monitor session command.
To disable monitoring a SPAN session(s), use the no form of this command.
monitor session {session-number [shut | type erspan-source] | all shut}
no monitor session {session-number [shut | type erspan-source] | all shut}
Syntax Description
Defaults
None
Command Modes
Global configuration (config)
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to enter the monitor configuration mode for configuring SPAN session number 2 for analyzing traffic between ports:
n1000v#
configuration t
n1000v(config)#
monitor session 2
n1000v(config-monitor)#
This example shows how to remove the configuration for SPAN session 2 for analyzing traffic between ports:
n1000v#
configuration t
n1000v(config)#
no monitor session 2
n1000v(config)#
Related Commands
|
|
---|---|
show monitor |
Displays Ethernet SPAN information. |
move
To move a file from one directory to another, use the move command.
move [filesystem:[//module/][directory/] | directory/]source-filename {{filesystem:[//module/][directory/] | directory/}[destination-filename] | target-filename}
Syntax Description
Defaults
The default name for the destination file is the same as the source filename.
Command Modes
Any
network-admin
Command History
|
|
---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
You can make a copy of a file by using the copy command.
Tip You can rename a file by moving it within the same directory.
Examples
This example shows how to move a file to another directory:
n1000v# move file1 my_files:file2
This example shows how to move a file to another file system:
n1000v# move file1 slot0:
This example shows how to move a file to another supervisor module:
n1000v# move file1 bootflash://sup-remote/file1.bak
Related Commands
|
|
---|---|
cd |
Changes the current working directory. |
copy |
Makes a copy of a file. |
dir |
Displays the directory contents. |
pwd |
Displays the name of the current working directory. |
mtu
To configure the maximum transmission unit (MTU) size for an interface, use the mtu command. To remove the configured MTU size from the interface, use the no form of this command.
mtu size
no mtu size
Syntax Description
size |
Specifies the MTU size. The range is 1500 to 9000. |
Defaults
1500 Bytes
Command Modes
Interface configuration (config-if)
network-admin
Command History
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to set the MTU size to 2000:
n1000v#
configure terminal
n1000v(
config)#
interface port-channel 2
n1000v(
config-if)#
mtu 2000
Related Commands
|
|
---|---|
show interface |
Displays information about the interface, which includes MTU size. |