Table of Contents

Preface

New and Changed

B Commands

C Commands

D Commands

F Commands

H Commands

I Commands

L Commands

M Commands

P Commands

Q Commands

S Commands

Show Commands

U Commands

W Commands

Title

Preface

This preface describes the audience, organization, and conventions of the Cisco Nexus 6000 Series NX-OS QoS Command Reference. It also provides information on how to obtain related documentation.

This preface includes the following sections:

- Audience

- Document Conventions

- Related Documentation

- Obtain Documentation and Submit a Service Request

Audience

This publication is for experienced users who configure and maintain Cisco NX-OS devices.

Document Conventions

Command descriptions use these conventions:

Convention

Description

boldface font

Commands and keywords are in boldface.

italic font

Arguments for which you supply values are in italics.

[ ]

Elements in square brackets are optional.

{x | y | z}

Alternative keywords are grouped in braces and separated by vertical bars.

[ x | y | z ]

Optional alternative keywords are grouped in brackets and separated by vertical bars.

string

A nonquoted set of characters. Do not use quotation marks around the string or the string will include the quotation marks.

Screen examples use these conventions:

screen font

Terminal sessions and information that the switch displays are in screen font.

boldface screen font

Information you must enter is in boldface screen font.

italic screen font

Arguments for which you supply values are in italic screen font.

< >

Nonprinting characters, such as passwords, are in angle brackets.

[ ]

Default responses to system prompts are in square brackets.

!, #

An exclamation point (!) or a pound sign (#) at the beginning of a line of code indicates a comment line.

This document uses the following conventions:

Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the manual.

Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Related Documentation

Documentation for the Cisco Nexus 6000 Series Switch is available at the following URL:

http://www.cisco.com/en/US/products/ps12806/tsd_products_support_series_home.html

The documentation set is divided into the following categories:

Release Notes

The release notes are available at the following URL:

http://www.cisco.com/en/US/products/ps12806/prod_release_notes_list.html

Installation and Upgrade Guides

The installation and upgrade guides are available at the following URL:

http://www.cisco.com/en/US/products/ps12806/prod_installation_guides_list.html

Command References

The command references are available at the following URL:

http://www.cisco.com/en/US/products/ps12806/prod_command_reference_list.html

Technical References

The technical references are available at the following URL:

http://www.cisco.com/en/US/products/ps12806/prod_technical_reference_list.html

Configuration Guides

The configuration guides are available at the following URL:

http://www.cisco.com/en/US/products/ps12806/products_installation_and_configuration_guides_list.html

Error and System Messages

The system message reference guide is available at the following URL:

http://www.cisco.com/en/US/products/ps12806/products_system_message_guides_list.html

Documentation Feedback

To provide technical feedback on this document, or to report an error or omission, please send your comments to nexus6k-docfeedback@cisco.com. We appreciate your feedback.

Obtain Documentation and Submit a Service Request

For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What’s New in Cisco Product Documentation.

To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the What’s New in Cisco Product Documentation RSS feed. The RSS feeds are a free service.

New and Changed Information

This chapter provides release-specific information for each new and changed feature in the Cisco Nexus 6000 Series NX-OS QoS Command Reference. The latest version of this document is available at the following Cisco website:

http://www.cisco.com/c/en/us/support/switches/nexus-6000-series-switches/products-command-reference-list.html

To check for additional information about this Cisco NX-OS Release, see the Cisco Nexus 6000 Series NX-OS Release Notes, Release 6.0 available at the following Cisco website:

http://www.cisco.com/c/en/us/support/switches/nexus-6000-series-switches/products-release-notes-list.html

New and Changed Information for Cisco NX-OS Releases

This section includes the following topics:

- New and Changed Information for Cisco NX-OS Release 7.0(1)N1(1)

- New and Changed Information for Cisco NX-OS Release 7.0(3)N1(1)

New and Changed Information for Cisco NX-OS Release 7.0(1)N1(1)

Table 1 summarizes the new and changed features for Cisco NX-OS Release 7.0(1)N1(1) and tells you where they are documented.

Table 1 New and Changed Information for Release 7.0(1)N1(1)

Feature

Description

Where Documented

IPv6 ACL Logging

New feature to monitor ACL flows and log dropped packets on an interface.

logging ip access-list cache

New and Changed Information for Cisco NX-OS Release 7.0(3)N1(1)

Table 2 summarizes the new and changed features for Cisco NX-OS Release 7.0(3)N1(1) and tells you where they are documented.

Table 2 New and Changed Information for Release 7.0(3N1(1)

Feature

Description

Where Documented

FEX-based ACL Classification

New feature that uses TCAM resources on a FEX to perform ACL-based packet classification of incoming packets on the switch.

B Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with B.

bandwidth (QoS)

To allocate a minimum percentage of the interface bandwidth to a queue and configure the bandwidth on both ingress and egress queues, use the bandwidth command. To remove a bandwidth configuration, use the no form of this command.

bandwidth percent percent

no bandwidth percent percent

Syntax Description

percent

Specifies the percentage of bandwidth of the underlying link rate.

percent

Percent value. The range is from 0 to 100.

Command Default

Default bandwidth rate is kbps.

Command Modes

Policy map type queuing class configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to set the bandwidth for the specified queue:

switch(config)# policy-map type queuing my_policy1

switch(config-pmap-que)# class type queuing 1p7q4t-out-pq1

switch(config-pmap-c-que)# bandwidth percent 25

switch(config-pmap-c-que)#

This example shows how to remove the bandwidth for the specified queue:

switch(config)# policy-map type queuing my_policy1

switch(config-pmap-que)# class type queuing 1p7q4t-out-pq1

switch(config-pmap-c-que)# no bandwidth percent 25

switch(config-pmap-c-que)#

Related Commands

Command

Description

show class-map

Displays class maps.

show policy-map

Displays policy maps.

burst maximum

To configure the maximum number of bursts allowed within a time interval before generating an interrupt, use the burst maximum command. To remove the micro-burst maximum configuration, use the no form of this command.

burst maximum {ingress | egress} burst-count max-burst

no burst maximum

Syntax Description

ingress

Specifies that the configuration applies to ingress ports only.

egress

Specifies that the configuration applies to egress ports only.

burst-count max-burst

The maximum number of bursts allowed before the system generates an interrupt. The range is from 1 to 4194303.

Command Default

An interrupt is generated when a micro-burst is detected.

Command Modes

Interface configuration (config-if)

Command History

Release

Modification

7.0(0)N1(1)

This command was introduced.

Usage Guidelines

By default, the system generates an interrupt as soon as it detects a micro-burst. However, you can use the burst maximum command to define a maximum number of bursts that can occur before the system generates an interrupt.

You use this command to configure the maximum number of bursts allowed with a time interval before the system generates an interrupt on a port in the ingress and egress directions. The time interval is calculated as ten times the micro-burst threshold interval (in seconds).

Examples

This example shows how to configure micro-burst thresholds for the ingress ports on an interface:

switch(config)# interface ethernet 1/1

switch(config-if)# burst threshold ingress limit 60 interval 10000000

sswitch(config-if)# #

This example shows how to remove the microburst configuration for ingress ports on the specified interface:

switch(config)# interface ethernet 1/1

switch(config-if)# no burst threshold ingress

switch(config-if)#

Related Commands

Command

Description

burst threshold

Configures micro-burst threshold values for an interface.

clear burst-counters

Clears burst counter values.

show interface burst-counters

Displays burst counter information.

burst threshold

To configure micro-burst threshold values for an interface, on both ingress and egress ports, use the burst threshold command. To remove micro-burst threshold configuration, use the no form of this command.

burst threshold {ingress | egress} {limit percent | size max_bytes} interval interval_time

no burst threshold {ingress | egress}

Syntax Description

ingress

Specifies that the configuration applies to ingress ports only.

egress

Specifies that the configuration applies to egress ports only.

limit percent

Sets the burst threshold to a percentage of the link speed. The range is from 1 to 100.

size max_bytes

Sets the burst threshold to a maximun number of bytes. The range is from 1 to 68719476735 bytes.

interval interval_time

Sets the micro-burst monitoring time interval in micro seconds. The range is from 1 to 16777215.

Command Default

Burst threshold is not configured.

Command Modes

Interface configuration (config-if)

Command History

Release

Modification

7.0(0)N1(1)

This command was introduced.

Usage Guidelines

Use this command to enable micro-burst detection on a port. If activity occurs on the port that meets the specified criteria, it is identified as a micro-burst and the appropriate burst counters are incremented.

Examples

This example shows how to configure micro-burst thresholds for the ingress ports on an interface:

switch(config)# interface ethernet 1/1

switch(config-if)# burst threshold ingress limit 60 interval 10000000

sswitch(config-if)# #

This example shows how to remove the microburst configuration for ingress ports on the specified interface:

switch(config)# interface ethernet 1/1

switch(config-if)# no burst threshold ingress

switch(config-if)#

Related Commands

Command

Description

burst maximum

Configures the maximum number of bursts allowed within a time interval before generating an interrupt.

clear burst-counters

Clears burst counter values.

show interface burst-counters

Displays burst counter information.

C Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with C.

class (control plane policy map)

To specify a control plane class map for a control plane policy map, use the class command. To delete a control plane class map from a control plane policy map, use the no form of this command.

class class-map-name

no class class-map-name

Syntax Description

class-map-name

Name of the class map. The name is alphanumeric, case sensitive, and has a maximum of 64 characters.

Command Default

None

Command Modes

Control plane policy map configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You must create the control plane class maps before you reference them in this command.

This command does not require a license.

Examples

This example shows how to configure a class map for a control plane policy map:

switch# configure terminal

switch(config)# policy-map type control-plane copp-system-policy-customized

switch(config-pmap)# class copp-system-class-dhcp

swtich(config-pmap-c)# police cir 300 bc 1500

swtich(config-pmap-c)#

Related Commands

Command

Description

class-map type control-plane

Creates or configures a control plane class map.

police (policy map)

Configures policing for a class map in a control plane policy map.

policy-map type control-plane

Specifies a control plane policy map and enters policy map configuration mode.

show policy-map type control-plane

Displays configuration information for control plane policy maps.

class (policy map type qos)

To add a reference to an existing qos class map in a policy map and enter the class mode, use the class command. To remove a class from the policy map, use the no form of this command.

class [type qos] class-map-name

no class class-map-name

Syntax Description

type qos

(Optional) Specifies the component type, which is qos for this class. By default, the type is qos.

class-map-name

Reference to a class map. The class map name can be a maximum of 40 characters. The name is case sensitive and can only contain alphabetic characters, numbers, hyphens, and underscores.

Command Default

None

Command Modes

Policy map type qos configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Policy actions in the first class that matches the traffic type are performed.

By default, the class-default class of type qos is created under every policy map of type qos in the system and it is mapped to the QoS group 0. You cannot change this mapping.

You cannot remove the class-default of type qos. If you attempt to delete the class-default class, the switch returns an error message.

Examples

This example shows how to add a reference to a qos class map at the end of a policy map:

switch(config)# policy-map my_policy1

switch(config-pmap-qos)# class traffic_class2

switch(config-pmap-c-qos)#

This example shows how to remove a class map reference in a policy map:

switch(config)# policy-map my_policy1

switch(config-pmap-qos)# no class traffic_class1

switch(config-pmap-qos)#

Related Commands

Command

Description

set dscp

Assigns a DSCP value to the traffic class.

set precedence

Assigns a IP precedence to the traffic class.

set qos-group

Assigns a QoS group to the traffic class.

show class-map type qos

Displays type qos class maps.

show policy-map

Displays policy maps.

class class-default

To add a reference to the system default class that does not match any traffic class, use the class class-default command.

class class-default

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

QoS policy map configuration mode

Control-plane policy map configuration mode

QoS policy map in switch profile configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Traffic that fails to match any class is assigned to a default class of traffic called class-default. You cannot delete this class.

Examples

This example shows how to add a reference to the system default class at the end of a policy map in a switch profile:

switch# configure sync

Enter configuration commands, one per line. End with CNTL/Z.

switch(config-sync)# switch-profile s5010

Switch-Profile started, Profile ID is 1

switch(config-sync-sp)# policy-map type qos my_policy1

switch(config-sync-sp-pmap-qos)# class class-default

switch(config-sync-sp-pmap-c-qos)#

Related Commands

Command

Description

set dscp

Sets the DSCP value for the QoS traffic.

set precedence

Sets the IP precedence value for the QoS traffic.

set qos-group

Assigns a QoS group identifier for a class of traffic.

show policy-map

Displays policy maps.

show switch-profile

Displays information about the switch profile and the configuration revision.

switch-profile

Creates or configures a switch profile.

class type network-qos

To add a reference to an existing network QoS class map in a policy map and enter the class mode, use the class type network-qos command. To remove a class from the policy map, use the no form of this command.

class type network-qos class-map-name

no class type network-qos class-map-name

Syntax Description

class-map-name

Reference to a network QoS class map. The class map name can be a maximum of 40 characters. The name is case sensitive and can only contain alphabetic characters, numbers, hyphens, and underscores.

Command Default

None

Command Modes

Policy map type network-qos configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Policy actions in the first class that matches the traffic type are performed.

Examples

This example shows how to add a reference to a class map in a type network-qos policy map:

switch(config)# policy-map type network-qos nqos_policy

switch(config-pmap-nq)# class type network-qos nqos_class

switch(config-pmap-nq-c)#

This example shows how to remove a class map reference in a type network-qos policy map:

switch(config)# policy-map type network-qos nqos_policy

switch(config-pmap-nq)# no class type network-qos nqos_class

switch(config-pmap-nq)#

Related Commands

Command

Description

mtu

Enables jumbo frames on a traffic class.

pause no-drop

Enables Class-based Flow Control (CBFC) pause characteristics on a traffic class.

queue-limit

Configures queue limits for the traffic class.

set cos

Assigns a CoS value for a class of traffic.

show class-map type network-qos

Displays type network-qos class maps.

show policy-map

Displays policy maps.

class type queuing

To add a reference to an existing queuing class map in a policy map and enter the class mode, use the class type queuing command. To remove a class from the policy map, use the no form of this command.

class type queuing class-map-name

no class type queuing class-map-name

Syntax Description

class-map-name

Reference to a queuing class map. The class map name can be a maximum of 40 characters. The name is case sensitive and can only contain alphabetic characters, numbers, hyphens, and underscores.

Command Default

None

Command Modes

Policy map type queuing configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Policy actions in the first class that matches the traffic type are performed.

Examples

This example shows how to add a reference to a class map in a type queuing policy map:

switch(config)# policy-map type queuing my_policy1

switch(config-pmap-que)# class type queuing 1p7q4t-out-q3

switch(config-pmap-c-que)#

This example shows how to remove a class map reference in a type queuing policy map:

switch(config)# policy-map type queuing my_policy1

switch(config-pmap-que)# no class type queuing 1p7q4t-out-q3

switch(config-pmap-que)#

Related Commands

Command

Description

show class-map type queuing

Displays the type queuing class maps.

show policy-map

Displays policy maps.

class-map

To create or modify a class map and enter the class-map configuration mode, use the class-map command. To remove a class map, use the no form of this command.

class-map [type qos] [match-all | match-any] class-map-name

no class-map [type qos] [match-all | match-any] class-map-name

Syntax Description

type qos

(Optional) Specifies the component type qos for the class map. By default, the class map type is qos.

match-all

Specifies that if the packet matches all the criteria configured for this class map with the match command, then this class map is applied to the packet.

match-any

Specifies that if the packet matches any of the criteria configured for this class map with the match command, then this class map is applied to the packet. This is the default action if match-all is not specified.

class-map-name

Name assigned to the QoS class map. The name can be a maximum of 40 characters. The name is case sensitive and can only contain alphanumeric characters, hyphens, and underscores.

The names class-default and class-fcoe are reserved.

Command Default

type—qos

match-all

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can define a class map for each class of traffic to be used in QoS policies.

If the packet matches any of the criteria configured for this class map with the match command, then this class map is applied to the packet. If no execution strategy is specified (match-any or match-all), then the default value of match-any is applied to the traffic class.

Examples

This example shows how to create or modify a qos class map:

switch(config)# class-map my_class1

switch(config-cmap-qos)#

This example shows how to create a qos class map to match all traffic packets:

switch(config)# class-map type qos match-all my_class2

switch(config-cmap-qos)#

This example shows how to remove a qos class map:

switch(config)# no class-map my_class1

switch(config)#

This example shows the error message that appears when you attempt to remove a class-fcoe class map:

switch(config)# no class-map class-fcoe

ERROR: Reserved class-map(s) cannot be deleted/modified

switch(config)#

Related Commands

Command

Description

description

Adds a summary purpose for the class map.

feature fcoe

Enables FCoE on the switch.

match

Configures traffic class criteria.

policy-map type qos

Creates or modifies a qos policy map.

service-policy

Attaches a policy map to an interface or system policy.

show class-map type qos

Displays qos class maps.

class-map type control-plane

To create or specify a control plane class map and enter class map configuration mode, use the class-map type control-plane command. To delete a control plane class map, use the no form of this command.

class-map type control-plane [match-any] class-map-name

no class-map type control-plane [match-any] class-map-name

Syntax Description

match-any

(Optional) Specifies to match any match conditions in the class map.

class-map-name

Name of the class map. The name is alphanumeric and case-sensitive. The maximum length is 64 characters.

Command Default

match-any

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You cannot use match-any or class-default as names for control plane class maps.

You can delete only dynamic class-maps of type control-plane. You cannot delete static class-maps of type control-plane.

This command does not require a license.

Examples

This example shows how to specify a control plane class map and enter class map configuration mode:

switch# configure terminal

switch(config)# class-map type control-plane copp-system-class-dhcp

switch(config-cmap)#

This example shows how to delete a control plane class map:

switch# configure terminal

switch(config)# no class-map type control-plane copp-system-class-dhcp

switch(config)#

Related Commands

Command

Description

match access-group

Matches traffic with a specified access control list (ACL) group.

show class-map type control-plane

Displays control plane policy map configuration information.

class-map type network-qos

To create or modify a class map that defines a network QoS class of traffic and enter the class-map configuration mode, use the class-map type network-qos command. To remove a class map, use the no form of this command.

class-map type network-qos class_map_name

no class-map type network-qos class_map_name

Syntax Description

class-map-name

Name assigned to the class map. The name class-default is reserved. The name can be a maximum of 40 characters. The name is case sensitive and can only contain alphanumeric characters, hyphens, and underscores.

Command Default

None

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Class maps of type network qos support only the match qos-group command. If a traffic packet matches any of the criteria configured for this class map with the match command, then this class map is applied to the packet. By default, traffic is filtered using the implicit match-any option.

Examples

This example shows how to create or modify a network qos class map named my_class1:

switch(config)# class-map type network-qos my_class1

switch(config-cmap-nq)#

This example shows how to remove a network qos class map:

switch(config)# no class-map my_class1

switch(config)#

Related Commands

Command

Description

feature fcoe

Enables FCoE on a switch.

match qos-group

Defines a traffic class that matches the QoS group values.

show class-map type network-qos

Displays network qos class maps configured in the system.

class-map type queuing

To create or modify a class map that defines a queuing class of traffic and enter the class-map configuration mode, use the class-map type queuing command. To remove the queuing class map, use the no form of this command.

class-map type queuing class_map_name

no class-map type queuing class_map_name

Syntax Description

class-map-name

Name assigned to the class map or a system-defined queuing class map name. The name class-default is reserved. The name can be a maximum of 40 characters. The name is case sensitive and can only contain alphanumeric characters, hyphens, and underscores.

Command Default

None

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

If you modify the queuing type class maps, the configuration for all ports of the specified port type also changes.

You cannot delete the system-defined queuing class map names.

Class maps of type queuing support only the match qos-group command. If a traffic packet matches any of the criteria configured for this class map with the match command, then this class map is applied to the packet. By default, traffic is filtered using the implicit match-any option.

Examples

This example shows how to create or modify a queuing class map:

switch(config)# class-map type queuing my_class1

switch(config-cmap-que)#

This example shows how to modify a system-defined queuing class map named class-default:

switch(config)# class-map type queuing match-any class-default

switch(config-cmap-que)#

This example shows how to remove a queuing class map:

switch(config)# no class-map type queuing my_class1

switch(config)#

Related Commands

Command

Description

feature fcoe

Enables FCoE on the switch.

match qos-group

Configures a traffic class that matches the QoS group values.

show class-map type queuing

Displays queuing class maps configured in the system.

clear burst counters

To clear the micro-burst counters, use the clear burst counters command.

clear burst-counters [interface {all | ethernet interface}] {both | egrees | ingress }

Syntax Description

interface

(Optional) Clears interface burst counters.

all

Clears burst counters for all interfaces.

ethernet interface

Clears burst counters for the specified ethernet interface only.

ingress

Specifies that the configuration applies to ingress ports only.

egress

Specifies that the configuration applies to egress ports only.

both

Specifies that the configuration applies to both ingress and egress ports.

Command Default

None.

Command Modes

All

Command History

Release

Modification

7.0(0)N1(1)

This command was introduced.

Usage Guidelines

When the burst threshold command is used to enable micro-burst detection on a port, any activity that occurs on the port and that meets the specified criteria, is identified as a micro-burst and the appropriate burst counters are incremented. To clear the burst counters, you use the clear burst counters command.

Examples

This example shows how to clear all burst counters for an ethernet interface:

switch# clear burst counters interface ethernet 1/1 both

switch#

Related Commands

Command

Description

burst threshold

Configures micro-burst threshold values for an interface.

burst maximum

Configures the maximum number of bursts allowed within a time interval before generating an interrupt.

show interface burst-counters

Displays burst counter information.

clear copp statistics

To clear Control Plane Policing (CoPP) statistics, use the clear copp statistics command.

clear copp statistics

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Any configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to clear the CoPP statistics:

switch# clear copp statistics

switch#

Related Commands

Command

Description

class-map type control-plane

Configures a control plane class map.

show policy-map interface control-plane

Displays the CoPP statistics for interfaces.

clear hardware profile latency monitor

To clear switch latency monitoring statistics for egress and ingress port pairs, use the clear hardware profile latency monitor command.

clear hardware profile latency monitor {all | interface ethernet egress-interface-slot/port interface ethernet ingress-interface-slot/port}

Syntax Description

all

Clears the statistics for all egress and ingress port pairs in the system.

interface

Clears the statistics for the specified interface.

ethernet egress-interface-slot/port

Specifies a single egress Ethernet interface and its slot number and port number. The slot number is from 1 to 255. The port number is from 1 to 128.

ethernet ingress-interface-slot/port

Specifies a single ingress Ethernet interface and its slot number and port number. The slot number is from 1 to 255. The port number is from 1 to 128.

Command Default

None

Command Modes

Any configuration mode

Command History

Release

Modification

7.0(0)N1(1)

This command was introduced.

Usage Guidelines

This command does not require a license.

If you reload the card or a module is powered on, you must use the clear hardware profile latency monitor all command to clear the switch latency monitoring statistics.

Examples

The following example shows how to clear all switch latency monitoring statistics:

switch# clear hardware profile latency monitor interface all

The following example shows how to clear switch latency monitoring configuration and statistics information for the specified egress and ingress port pairs:

switch# clear hardware profile latency monitor interface ethernet 1/1 interface ethernet 1/2

Related Commands

Command

Description

clear hardware profile latency monitor

Clears switch latency monitoring statistics.

hardware profile latency monitor base

Specifies the histogram base value to construct switch latency monitoring histograms.

packet latency interface

Enables switch latency histogram monitoring.

show hardware profile latency monitor

Displays switch latency statistics for egress and ingress port pairs.

clear hardware internal bigsur port interface qos-drop-history detail

To clear QoS packet drop history detail, use the clear hardware internal bigsur port interface qos-drop-history detail command in EXEC mode.

clear hardware internal bigsur port ethernet [slot/port] qos-drop-history detail {all | multicast | unicast}

Syntax Description

ethernet 1/1

Specifies Ethernet interface with its slot number and port number as 1/1

slot

Specifies the slot number on the selected interface.

port

Specifies the port number on the selected interface.

all

Specifies the qos drop history brief of type all.

multicast

Specifies the qos drop history brief of type multicast.

unicast

Specifies the qos drop history brief of type unicast.

Command Default

None

Command Modes

EXEC mode

Command History

Release

Modification

7.2(0)N1(1)

This command was introduced.

Examples

This example shows how to clear all QoS packet drop for QoS-drop-history for all ports:

switch# clear hardware internal bigsur all-ports qos-drop-history all

QoS all drops history Cleared for all-ports Cleared

This example shows how to clear multicast QoS packet drop for QoS-drop-history for all ports:

switch# clear hardware internal bigsur all-ports qos-drop-history multicast

QoS multicast drop history for all-ports Cleared

This example shows how to clear unicast QoS packet drop for QoS-drop-history for all ports:

switch# clear hardware internal bigsur all-ports qos-drop-history unicast

QoS unicast drop history for all-ports Cleared

This example shows how to clear all QoS packet drop for QoS-drop-history for port ethernet 1/1:

switch# clear hardware internal bigsur port ethernet 1/1 qos-drop-history all

QoS all drops history Cleared

This example shows how to clear multicast QoS packet drop for QoS-drop-history for port ethernet 1/1:

switch# clear hardware internal bigsur port ethernet 1/1 qos-drop-history multicast

QoS multicast drop history Cleared

This example shows how to clear unicast QoS packet drop for QoS-drop-history for port ethernet 1/1:

switch# clear hardware internal bigsur port ethernet 1/1 qos-drop-history unicast

QoS unicast drop history Cleared

Related Commands

Command

Description

show hardware internal bigsur port ethernet qos-drop-history detail.

To display the number of Ingress QoS multicast packet drops with a timestamp for the Ethernet interface 1/1.

control-plane

To enter control-plane configuration mode, which allows users to associate attributes that are associated with the control plane of the device, use the control-plane command.

control-plane

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

After you use the control-plane command, you can associate a service policy to police all traffic that is destined to the control plane.

Examples

This example shows how to enter the control plane configuration mode:

switch# configure terminal

switch(config)# control-plane

switch(config-cp)#

Related Commands

Command

Description

service-policy (control-plane)

Attaches a policy map to a control plane for aggregate control plane services.

show policy-map type control-plane

Displays the configuration of a class or all classes for the policy map of a control plane.

D Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with D.

description

To add a description to a class map, policy map, or table map, use the description command. To remove the description, use the no form of this command.

description text

no description text

Syntax Description

text

Description for the class map, policy map, or table map. The description can be a maximum of 200 alphanumeric characters.

Command Default

None

Command Modes

Class map type network qos configuration

Class map type qos configuration

Class map type queuing configuration

Policy map type network qos configuration

Policy map type qos configuration

Policy map type queuing configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

Creates or modifies a class map.

policy-map

Creates or modifies a policy map.

show class-map

Displays class maps.

show policy-map

F Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with F.

flowcontrol

To enable IEEE 802.3x link-level flow control for the selected interface, use the flowcontrol command.

flowcontrol [receive {on | off}] [send {on | off}]

Syntax Description

receive

(Optional) Sets flow control in the receive direction.

off

Disables flow control traffic on an interface.

on

Enables flow control traffic on an interface.

send

(Optional) Sets flow control in the send direction.

Command Default

None

Command Modes

Interface configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can use this command on the following interfaces:

- Layer 2 interface

- Layer 3 interface

Note Use the no switchport command to configure an interface as a Layer 3 interface.

Examples

Configures an interface as a Layer 3 routed interface.

priority-flow-control

Sets the PFC mode for the selected interface.

show interface flowcontrol

H Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with H.

hardware pq-drain

To configure the proxy-queue drain rate settings, use the hardware pq-drain command in global confiiguration mode. To disable proxy-queue drain settings, use the no form of this command.

hardware pq-drain 10g 10g-drain-rate 40g 40g-drain-rate

no hardware pq-drain 10g 10g-drain-rate 40g 40g-drain-rate

Syntax Description

10g 10g-drain-rate

Proxy Queue drain rate for the 10 G interface. The range is from 1 Mbps to 20000 Mbps.

40g 40g-drain-rate

Proxy Queue drain rate for the 40 G interface. The range is from 1 Mbps to 80000 Mbps.

Command Default

Disabled

Command Modes

Global configuration mode

Command History

Release

Modification

7.0(0)N1(1)

This command was introduced.

Usage Guidelines

Note This command is applicable to only Cisco Nexus 6000 switches.

When the proxy queue reaches a threshold that indicates congestion, Explicit Congestion Notification (ECN) marking is performed so that the receiver of the packet echoes the congestion indication to the sender. The proxy-queue drain rate is configured to ensure that during congestion at egress ports only a certain amount of packets are drained.

Examples

This example shows how to configure proxy-queue settings to drain 9900 Mbps of traffic from 10 Gigabait interfaces and 39900 Mpbs of traffic from 40 Gigabit interfaces:

switch(config)# hardware pq-drain 10g 9900 40g 39900

Related Commands

Command

Description

hardware random-detect

Configures ECN for a QoS group.

hardware profile latency monitor base

To specify the histogram base-value time to construct switch latency monitoring histograms, use the hardware profile latency monitor base command in global configuration mode. To remove switch latency monitoring base values, use the no form of this command.

hardware profile latency monitor base base-value

no hardware profile latency monitor base

Syntax Description

base-value

Histogram base value used to construct switch latency monitoring histograms. Valid values are multiples of 8 in the range 8 to 2147483640 nanoseconds.

Command Default

Disabled

Command Modes

Global configuration mode

Command History

Release

Modification

7.0(0)N1(1)

This command was introduced.

Usage Guidelines

Note This command is applicable to Cisco Nexus 6000 switches only.

If you enter a base value that is not a multiple of 8, the system automatically modifies the base value to the nearest (lower) number that is a multiple of 8.

Note All previous histogram statistics are lost when you configure, update or delete the base value.

Examples

This example shows how to configure a histogram base value of 800 nanoseconds:

switch(config)# hardware profile latency monitor base 800

Related Commands

Command

Description

clear hardware profile latency monitor

Clears switch latency monitoring statistics.

hardware profile latency monitor

Specifies the histogram base value to construct switch latency monitoring histograms.

packet latency interface

Enables switch latency histogram monitoring.

show hardware profile latency monitor

hardware profile tcam feature interface-qos limit tcam-size

Syntax Description

tcam-size

Interface QoS TCAM limit. The TCAM size can be from 7- 446 entries.

Command Default

None

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

No interface policy entry should be present after the interface_qos limit in the QoS region of any TCAM.

Examples

This example shows how to set the interface QoS TCAM limit to 20 entries:

switch(config)# configue terminal

switch(config)# hardware profile tcam feature interface-qos limit 20

switch(config)# show hardware profile tcam feature qos

Feature Limit

--------------------------------------------------------------------------------

Interface 20

vlan-qos + global-qos 428

switch(config)# copy running-config startup-config

Related Commands

Command

Description

show hardware profile tcam feature qos

Displays the limits of the QoS TCAMs.

hardware card-type qos-policy-offload

no hardware card-type qos-policy-offload

Syntax Description

card-type

Fabric Extender card type. The following Fabric Extender card types are supported:

- N2224TP —Fabric Extender 24x1G 2x10G SFP+ Module

- N2232P —Fabric Extender 32x10G SFP+ 8x10G SFP+ Module

- N2232TM —Fabric Extender 32x10GBase-T 8x10G SFP+ Module

- N2248T —Fabric Extender 48x1G 4x10G SFP+ Module

- N2248TP-E —Fabric Extender 48x1G 4x10G SFP+ Module

- N2248PQ —Fabric Extender 48x10G SPF+ 16x10G SFP+ Module

- N2232TM-E —Fabric Extender 32x10GBase-T 8x10G SFP+ Module

- NB22IBM —Fabric Extender 14x10G SFP+ 8x10G SFP+ Module

Command Default

Disabled

Command Modes

Fabric extender configuration mode (config-fex)#

Command History

Release

Modification

7.0(3)N1(1)

This command was introduced.

Usage Guidelines

If the existing system-level QoS policy is accepted by the FEX, the QoS policy is enforced by the FEX.

If the existing system-level QoS policy is not accepted by the FEX, an error message is displayed and the fabric ports associated with the FEX are error-disabled, which prevents the FEX from being online.

When you disable the feature, the existing system-level QoS policy is removed from the FEX and the enforcement of the existing QoS policy is changed from ACL-based to Class-of-Service (CoS) based. The TCAM entries are removed and packet classification on the FEX is done using the cos2q map in the FEX hardware.

The maximum number of access control entries (ACEs) in a policy applied on the FEX is 30 when offloaded. In Cisco NX-OS Release 7.3(x), the FEX offload capability using interface QoS policies is up to 100 ACEs and up to only 30 ACEs using system QoS policies.

Examples

switch(config)# fex 110

switch(config-fex)# no hardware N2248T qos-policy-offload

switch(config-fex)#

Related Commands

Command

Description

fex

Creates a Fabric Extender and enters fabric extender configuration mode.

show fex

Displays all configured Fabric Extender chassis connected to the switch.

show running-config

Displays the contents of the currently running configuration file, including information on FEX-based ACL classification settings.

hardware random-detect min-thresh 10g 10g-min-theshold 40g 40g-min-threshold max-thresh 10g 10g-max-threshold 40g 40g-max-threshold ecn qos-group group-number

no hardware randon-detect 10g 10g-min-theshold 40g 40g-min-threshold max-thresh 10g 10g-max-threshold 40g 40g-max-threshold ecn qos-group group-number

Syntax Description

min-thresh

Minimum threshold.

10g 10g-min-theshold

Minimum threshold for 10 Gigabit interfaces. The range is from 1 to 67108863 bytes.

40g 40g-min-threshold

Minimum threshold for 40 Gigabit interfaces. The range is from 1 to 67108863 bytes.

max-thresh

Maximum threshold.

10g 10g-max-threshold

Maximum threshold for 10 Gigabit interfaces. The range is from 1 to 67108863 bytes.

40g 40g-max-threshold

Maximum threshold for 40 Gigabit interfaces. The range is from 1 to 67108863 bytes.

ecn

Enables ECN for the specified QoS group.

qos-group group-number

Specifies the QoS group that is being configured.

Command Default

Disabled

Command Modes

Global configuration mode

Command History

Release

Modification

7.0(0)N1(1)

This command was introduced.

Usage Guidelines

Note This command is applicable to only Cisco Nexus 6000 switches.

To implement Weighted Random Early Detection (WRED) Explicit Congestion Notification (ECN) on proxy queues you use the hardware random-detect command to configure minimum and maximum threshold values per QoS group. Then you use the hardware pq-drain command to configure the proxy-queue drain rate.

Examples

This example shows how to enable ECN threshold values for the class-default QoS group:

switch(config)# hardware random-detect min-thresh 10g 64000 40g 4000 max-thresh 10g 128000

40g 246000 ecn qos-group 0

Related Commands

Command

Description

hardware pq-drain

Configures proxy queue drain rate.

hardware unicast voq-limit

no hardware unicast voq-limit

Syntax Description

This command has no arguments or keywords.

Command Default

Disabled

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

To alleviate congestion and blocking, you can use virtual output queuing (VOQ) to prevent one blocked receiver from affecting traffic that is being sent to other noncongested receivers (head-of-line blocking).

Examples

Disables slow port pruning on the switch.

show running-config

hardware unicast voq-limit-sup

no hardware unicast voq-limit-sup

Syntax Description

This command has no arguments or keywords.

Command Default

Disabled

Command Modes

Global configuration

Command History

Release

Modification

7.1(4)N1(1)

This command was introduced.

Usage Guidelines

In a virtual port channel (vPC) topology, enable the command on both the vPC peers.

Note We recommend that you enable this command under the supervision of Cisco Systems Technical Assistance Center.

Examples

Enables the VOQ limit for unicast traffic on a switch.

show running-config

I Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with I.

ip dscp (ERSPAN)

To configure the differentiated dervices code point (DSCP) value of the packets in the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic, use the ip dscp command. To revert to the default value, use the no form of this command.

ip dscp dscp_value

no ip dscp dscp_value

Syntax Description

dscp_value

DSCP value of the packets in the ERSPAN traffic. The range is from 0 to 63.

Command Default

0

Command Modes

ERSPAN session configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to configure the DSCP value of the packets in the ESRSPAN traffic:

switch# configure terminal

switch(config)# monitor session 1 type erspan-source

switch(config-erspan-src)# ip dscp 10

switch(config-erspan-src)#

Related Commands

Command

Description

ip prec

Configures the IP precedence value of the ERSPAN traffic.

ip ttl

Configures the IP time-to-live (TTL) value of the ERSPAN traffic.

monitor-session

Enters the monitor configuration mode for configuring an ERSPAN session for analyzing traffic between ports.

ip ttl (ERSPAN)

To configure the IP time-to-live (TTL) value of the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic, use the ip ttl command. To revert to the default configuration, use the no form of this command.

ip ttl ttl_value

no ip ttl ttl_value

Syntax Description

ttl_value

IP TTL value of the ERSPAN traffic. The range is from 1 to 255.

Command Default

255

Command Modes

ERSPAN session configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to configure the IP TTL value of the ESRSPAN source:

switch# configure terminal

switch(config)# monitor session 1 type erspan-source

switch(config-erspan-src)# ip ttl 30

switch(config-erspan-src)#

This example shows how to remove the IP TTL value from the ESRSPAN source:

switch# configure terminal

switch(config)# monitor session 1 type erspan-source

switch(config-erspan-src)# no ip ttl 30

switch(config-erspan-src)#

Related Commands

Command

Description

ip dscp

Configures the DSCP value of the packets in the ERSPAN traffic.

monitor-session

Enters the monitor configuration mode for configuring an ERSPAN session for analyzing traffic between ports.

L Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with L.

logging ip access-list cache

To configure the ACL logging process, use the logging ip access-list cache command. To revert to the defaults, use the no form of this command.

logging ip access-list cache {interval interval | entries number-of-entries | threshold threshold }

no logging access-list cache {interval interval | entries number-of-entries | threshold threshold }

Syntax Description

interval interval

The log-update interval, in seconds, for the ACL logging process. The default value is 300 seconds. The range is from 5 to 86400 seconds.

entries number-of-entries

The maximum number of flows to be monitored. The default value is 8000. The range is from 0 to 1048576.

threshold threshold

Specifies the packet threshold. If this amount of packets are logged before the expiry of the alert interval, the system generates a Syslog message.

Command Default

Not configured

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(2)

This command was introduced.

Usage Guidelines

To configure the ACL logging process, you first create the IPv6 access-list with log option enabled, then enable filtering of IPv6 traffic on an interface using the specified ACL, and finally configure the ACL logging process parameters.

Examples

This example shows how to set the interval, entries and threshold values for IPv6 ACL logging:

switch(config)# logging ip access-list cache interval 400

switch(config)# logging ip access-list cache entries 100

switch(config)# logging ip access-list cache threshold 900

Related Commands

Command

Description

ipv6 access-list

Creates an IPv6 ACL.

ipv6 port traffic-filter

Applies an IPv6 ACL to an interface as a port ACL.

ipv6 traffic-filter

Applies an IPv6 ACL to an interface.

M Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with M.

match access-group

To identify a specified access control list (ACL) group as a match criteria for a class map, use the match access-group command. To remove an ACL match criteria from a class map, use the no form of this command.

match access-group name acl-name

no match access-group name acl-name

Syntax Description

name acl-name

Matches on the characteristics in the ACL name specified.

Command Default

None

Command Modes

Class-map type qos configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Note The permit and deny ACL keywords do not affect the matching of packets.

Examples

This example shows how to create a qos class map that matches characteristics of the ACL my_acl:

switch(config)# class-map class_acl

switch(config-cmap-qos)# match access-group name my_acl

Related Commands

Command

Description

show class-map

Displays class maps.

match cos

To define the class of traffic using the class of service (CoS) value in a type qos class map, use the match cos command. To remove the match on the CoS value, use the no form of this command.

match [not] cos cos-list

no match [not] cos cos-list

Syntax Description

not

(Optional) Negates the specified match result.

cos-list

Specified CoS value or list of specified CoS values. Valid values are from 0 to 7.

Command Default

None

Command Modes

Class-map type qos configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

To specify a list of values, use one of the following options:

- Specify a range of values separated by a dash

- Specify a noncontiguous list of values separated by commas

Note Only class maps of type qos support the optional not keyword form of this command. Class maps of type queuing do not support the not keyword.

Examples

This example shows how to match on the CoS value for a type qos class map:

switch(config)# class-map class_acl

switch(config-cmap-qos)# match cos 5-7

Related Commands

Command

Description

show class-map

Displays class maps.

match dscp

To identify specific differentiated services code point (DSCP) values in the DiffServ field of the IP Header (either IPv4 or IPv6) as a match criteria, use the match dscp command. To remove specified DSCP values as a match criteria, use the no form of this command.

match [not] dscp dscp-list

no match [not] dscp dscp-list

Syntax Description

not

(Optional) Negates the specified match result.

dscp-list

Specified DSCP value or list of DSCP values. See Table 1 for a list of valid DSCP values.

Command Default

None

Command Modes

Class-map type qos configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

The standard DSCP values are shown in Table 1.

Table 1 Standard DSCP Values

DSCP Value

Description

af11

AF11 dscp (001010)—decimal value 10

af12

AF12 dscp (001100)—decimal value 12

af13

AF13 dscp (001110)—decimal value 14

af21

AF21 dscp (010010)—decimal value 18

af22

AF22 dscp (010100)—decimal value 20

af23

AF23 dscp (010110)—decimal value 22

af31

AF31 dscp (011010)—decimal value 26

af32

AF40 dscp (011100)—decimal value 28

af33

AF33 dscp (011110)—decimal value 30

af41

AF41 dscp (100010)—decimal value 34

af42

AF42 dscp (100100)—decimal value 36

af43

AF43 dscp (100110)—decimal value 38

cs1

CS1 (precedence 1) dscp (001000)—decimal value 8

cs2

CS2 (precedence 2) dscp (010000)—decimal value 16

cs3

CS3 (precedence 3) dscp (011000)—decimal value 24

cs4

CS4 (precedence 4) dscp (100000)—decimal value 32

cs5

CS5 (precedence 5) dscp (101000)—decimal value 40

cs6

CS6 (precedence 6) dscp (110000)—decimal value 48

cs7

CS7 (precedence 7) dscp (111000)—decimal value 56

default

Default dscp (000000)—decimal value 0

ef

EF dscp (101110)—decimal value 46

To specify a list of values, use one of the following options:

- Specify a range of values separated by a dash

- Specify a noncontiguous list of values separated by commas

Examples

This example shows how to match on DSCP value af21:

switch(config)# class-map my_test

switch(config-cmap-qos)# match dscp af21

Related Commands

Command

Description

show class-map

Displays class maps.

match ip rtp

To configure a class map to use the Real-Time Protocol (RTP) port as a match criteria, use the match ip rtp command. To remove the RTP port as a match criteria, use the no form of this command.

match [not] ip rtp port-list

no match [not] ip rtp port-list

Syntax Description

not

(Optional) Negates the specified match result.

port-list

Specified UDP port or list of UDP ports that are using RTP. Valid values range from 2000 to 65535.

Command Default

None

Command Modes

Class-map type qos configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

To specify a list of values, use one of the following options:

- Specify a range of values separated by a dash

- Specify a noncontiguous list of values separated by commas

Examples

This example shows how to match on a port using RTP:

switch(config)# class-map my_test

switch(config-cmap-qos)# match ip rtp 2300

Related Commands

Command

Description

show class-map

Displays class maps.

match precedence

To configure a class map to use the precedence value in the type of service (ToS) byte field of the IP header (either IPv4 or IPv6) as a match criteria, use the match precedence command. To remove the precedence values as a match criteria, use the no form of this command.

match [not] precedence precedence-list

no match [not] precedence precedence-list

Syntax Description

not

(Optional) Negates the specified match result.

precedence-list

Specified IP precedence value or list of IP precedence values specified in bytes. Valid values are shown in Table 2.

Command Default

None

Command Modes

Class-map type qos configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

See Table 2 for a list of precedence values.

Table 2 Precedence Values

Precedence Value

Description

0-7

IP precedence value

critical

Critical precedence (5)

flash

Flash precedence (3)

flash-override

Flash override precedence (4)

immediate

Immediate precedence (2)

internet

Internetwork control precedence (6)

network

Network control precedence (7)

priority

Priority precedence (1)

routine

Routine precedence (0)

To specify a list of values, use one of the following options:

- Specify a range of values separated by a dash

- Specify a noncontiguous list of values separated by commas

Examples

This example shows how to match on an IP precedence value:

switch(config)# class-map my_test

switch(config-cmap-qos)# match precedence 7

Related Commands

Command

Description

show class-map

Displays class maps.

match protocol

To configure a class map to use a specific protocol as a match criterion, use the match protocol command. To remove the specified protocol as a match criteria, use the no form of this command.

match [not] protocol protocol-name

no match [not] protocol protocol-name

Syntax Description

not

(Optional) Negates the specified match result.

protocol-name

Specified protocol name. Valid values are shown in Table 3.

Command Default

None

Command Modes

Class-map type qos configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

The list of valid protocol names is shown in Table 3.

Table 3 Protocol Names

Argument

Description

arp

Address Resolution Protocol (ARP)

clns_es

CLNS End Systems

clns_is

CLNS Intermediate System

dhcp

Dynamic Host Configuration (DHCP)

isci

Internet Small Computer System Interface (iSCSI)

ldp

Label Distribution Protocol (LDP)

netbios

NetBIOS Extended User Interface (NetBEUI)

To specify more than one protocol, enter the command more than once with the desired protocol value each time.

Examples

This example shows how to match on a specified protocol:

switch(config)# class-map my_test

switch(config-cmap-qos)# match protocol ldp

Related Commands

Command

Description

show class-map

Displays class maps.

match qos-group

To configure a class map to use a specific QoS group value as a match criterion, use the match qos-group command. To remove the specified protocol as a match criteria, use the no form of this command.

match [not] qos-group qos-group-list

no match [not] qos-group qos-group-list

Syntax Description

not

(Optional) Negates the specified match result.

qos-group-list

Specified Qos group value or list of QoS group values specified in bytes. Valid values are from 2 to 5.

Command Default

None

Command Modes

Class map type network-qos configuration

Class map type queuing configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

The QoS group is an internal label and is not part of the packet payload or any packet header. The QoS group values have no mathematical significance. For example, a QoS group value of 2 is not greater than 1; the values are used only to internally differentiate QoS groups. As such, this value has local significance only.

You match on the QoS group only in egress policies because its value is undefined until you set it in an ingress policy.

To specify a list of values, use one of the following options:

- Specify a range of values separated by a dash

- Specify a noncontiguous list of values separated by commas

Examples

This example shows how to match on a specified QoS group value:

switch(config)# class-map type queuing my_test

switch(config-cmap-qos)# match qos-group 6

switch(config-cmap-qos)#

Related Commands

Command

Description

class-map type network-qos

Creates or modifies a network qos class map.

class-map type queuing

Creates or modifies a queuing class map.

show class-map

Displays class maps.

mtu (ERSPAN)

To set the maximum transmission unit (MTU) size for Encapsulated Remote Switched Port Analyzer (ERSPAN) packets in a monitor session, use the mtu command. To remove the configured MTU, use the no form of this command.

mtu mtu-value

no mtu mtu-value

Syntax Description

mtu-value

Maximum allowable MTU for ERSPAN packets in a monitor session. The range is from 64 to 1518 bytes.

Command Default

Default is no truncation enabled.

Command Modes

ERSPAN session configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

ERSPAN packets larger than the specified allowable size for the monitor session are truncated.

This command does not require a license.

Examples

This example shows how to set an MTU value for an ERSPAN session:

switch# configure terminal

switch(config)# monitor session 1 type erspan-source

switch(config-erspan-src)# erspan-id 100

switch(config-erspan-src)# mtu 100

switch(config-erspan-src)#

Related Commands

Command

Description

monitor session

Configures a SPAN or ERSPAN session.

show monitor session

Displays the SPAN or ERSPAN session configuration.

mtu (interface)

To configure the maximum transmission unit (MTU) size for Layer 2 and Layer 3 Ethernet interfaces, use the mtu command. To remove the configured MTU, use the no form of this command.

mtu mtu-value

no mtu mtu-value

Syntax Description

mtu-value

MTU value for the class of service (CoS). The range is from 64 to 9216.1500 to 9216.

Command Default

Default MTU value is 1500. For FCoE cos 3, the default is 2158.

Command Modes

Policy map type network-qos class configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can configure an MTU for each virtual link in the system.

Examples

This example shows how to set an MTU value for a class in a type network-qos policy map:

switch(config)# class-map type network-qos my_class1

switch(config-cmap-nq)# match qos-group 1

switch(config-cmap-nq)# exit

switch(config)# policy-map type network-qos my_policy1

switch(config-pmap-nq)# class type network-qos my_class1

switch(config-pmap-nq-c)# mtu 5000

switch(config-pmap-nq-c)#

Related Commands

Command

Description

service-policy

Attaches a policy map to an interface or system policy.

show class-map

Displays class maps.

show policy-map

Displays policy maps.

system qos

Configures a system policy.

P Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with P.

packet latency interface

To enable switch latency histogram monitoring and configure the monitoring mode, use the packet latency interface command in interface configuration mode. To disable switch latency monitoring use the no form of this command.

packet latency interface ethernet ingress-interface-slot/port mode {linear step step-value | exponential step step-value | custom low-latency low-value high-latency high-value}

no packet latency interface ethernet ingress-interface-slot/port

Syntax Description

ethernet ingress-interface-slot/port

Specifies a single ingress Ethernet interface and its slot number and port number. The slot number is from 1 to 255. The port number is from 1 to 128.

mode

Specifies the switch latency monitoring mode.

linear

Specifies linear histogram mode as the monitoring mode.

step step-value

Specifies the step size to be incremented. Valid values are multiples of 8 in the range 8 to 131064 nanoseconds.

exponential

Speechifies exponential histogram as the monitoring mode.

custom

Specifies custom histogram as the monitoring mode.

low-latency low-value

The low latency value in nanoseconds. Valid values are multiples of 8 in the range 8 to 536870904.

high-latency high-value

The high latency value in nanoseconds. Valid values are multiples of 8 in the range 8 to 536870904.

Command Default

Instantaneous mode monitoring is enabled.

Command Modes

Interface configuration (config-if)#

Command History

Release

Modification

7.0(0)N1(1)

This command was introduced.

Usage Guidelines

To configure the monitoring mode between an egress and ingress port pair, you must first enter interface configuration mode on the egress interface. Only one mode (instantaneous, linear, exponential, or custom) can be configured on a port pair at any time.

Note If switch latency monitoring mode is configured without a histogram base value, the system uses a default value of 0, and calculates the histogram buckets accordingly.

Examples

The following example shows how to configure various switch latency monitoring modes between the egress interface (ethernet 1/1) and three different ingress interfaces.

switch (config)# hardware profile latency monitor base 800

switch (config)# interface ethernet 1/1

switch (config-if)# packet latency interface ethernet 1/2 mode linear step 40

switch (config-if)# packet latency interface ethernet 1/3-4 mode exp step 40

switch (config-if)# packet latency interface ethernet 1/5 mode custom low 40 high 1200

Related Commands

Command

Description

clear hardware profile latency monitor

Clears switch latency monitoring statistics.

hardware profile latency monitor base

Specifies the histogram base value to construct switch latency monitoring histograms.

packet latency

Enables switch latency monitoring.

show hardware profile latency monitor

Displays switch latency statistics for egress and ingress port pairs.

pause no-drop

To enable Class Based Flow Control (CBFC) pause characteristics on a class referenced in a type network-qos policy map, use the pause command. To disable the CBFC pause characteristics on a class, use the no form of this command.

pause no-drop [pfc-cos pfc-cos-list]

no pause no-drop [pfc-cos pfc-cos-list]

Syntax Description

pfc-cos

(Optional) Specifies the CoS values to assert priority flow control (PFC) on.

pfc-cos-list

PFC CoS list. The range is from 0 to 7.

Use a comma (,) to separate multiple values, or a hyphen (-) to specify a range of values; for example, 0, 2, 3, or 2-5.

Command Default

By default, pause no-drop is off.

Command Modes

Policy map type network-qos class configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Ethernet interfaces use priority flow control (PFC) to provide lossless service to no-drop system classes. PFC implements pause frames on a per-class basis and uses the IEEE 802.1p CoS value to identify the classes that require lossless service.

You can configure PFC CoS only for traffic classes that match a criteria other than the CoS value (match cos).

Examples

This example shows how to enable pause no-drop on a class referenced in a type network-qos policy map:

switch(config)# class-map type network-qos my_class1

switch(config-cmap-nq)# match qos-group 2

switch(config-cmap-nq)# exit

switch(config)# policy-map type network-qos my_policy1

switch(config-pmap-nq)# class type network-qos my_class1

switch(config-pmap-nq-c)# pause no-drop

switch(config-pmap-nq-c)#

Related Commands

Command

Description

show class-map type network-qos

Displays type network-qos class maps.

show policy-map

Displays policy maps.

pause no-drop buffer-size

To enable Class Based Flow Control (CBFC) pause characteristics on a class referenced in a type network-qos policy map and configure the ingress buffer size for the no-drop class, use the pause no drop buffer-size command. To disable the CBFC pause characteristics on a class and reset the buffer, use the no form of this command.

pause no-drop buffer-size buffer-size pause-threshold xoff-size resume-threshold xon-size

no pause no-drop buffer-size buffer-size pause-threshold xoff-size resume-threshold xon-size

Syntax Description

buffer-size

Buffer size for ingress traffic, in bytes. Valid values are from 10240 to 490880.

Note On a Cisco Nexus device, you can configure a maximum buffer size of 152000 bytes.

pause-threshold

Specifies the buffer limit at which the port pauses the peer.

xoff-size

Buffer limit for pausing, in bytes. Valid values are from 0 to 490880.

Note On a Cisco Nexus device, you can configure a maximum pause threshold value of 103360 bytes.

resume-threshold

Specifies the buffer limit at which the port resumes the peer.

xon-size

Buffer limit at which to resume, in bytes. Valid values are from 0 to 490880.

Note On a Cisco Nexus device you can configure a maximum resume threshold value of 83520 bytes.

Command Default

By default, pause no-drop is on.

Command Modes

Policy map type network-qos class configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Use this command to configure the buffer size and threshold values for a no-drop class. You configure the buffer size to support lossless Ethernet over a link distance of 3000 meters (9843 feet). The switch software rejects the policy if enough buffer resources are not available to support the policy.

When you configure the buffer size, ensure the following:

- The pause threshold value must be greater than the resume threshold value. Otherwise, the following message appears:

ERROR: pause-threshold can't be less then resume-threshold

Examples

This example shows how to enable pause no-drop on a class referenced in a type network-qos policy map:

switch(config)# class-map type network-qos my_class1

switch(config-cmap-nq)# match qos-group 2

switch(config-cmap-nq)# exit

switch(config)# policy-map type network-qos my_policy1

switch(config-pmap-nq)# class type network-qos my_class1

switch(config-pmap-nq-c)# pause no-drop

switch(config-pmap-nq-c)#

This example shows how to set the no-drop buffer size for 3000 metres on a class referenced in a type network-qos policy map on a Cisco Nexus device:

switch(config-pmap-nq)# policy-map type network-qos policy-test

switch(config-pmap-nq)# class type network-qos cu1-ta1

switch(config-pmap-nq-c)# pause no-drop buffer-size 152000 pause-threshold 103360 resume-threshold 83520

switch(config-pmap-nq-c)#

Related Commands

Command

Description

show class-map type network-qos

Displays type network-qos class maps.

show policy-map

Displays policy maps.

police (policy map)

To configure traffic policing for a class map in a control plane policy map, use the police command.

police {rate | cir rate}

Syntax Description

rate

Average rate in packets per second (pps). The range is from 0 to 20480.

cir

Specifies the Committed Information Rate (CIR), in Kbps.

Command Default

None

Command Modes

Control plane policy map configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to configure traffic policing in a control plane policy map with the average rate at 200 packets per second:

switch# configure terminal

switch(config)# policy-map type control-plane copp-system-policy-customized

switch(config-pmap)# class ClassMapA

switch(config-pmap-c)# police 200

switch(config-pmap-c)#

Related Commands

Command

Description

class (policy map)

Specifies a control plane class map for a control plane policy map and enters policy map class configuration mode.

show policy-map type control-plane

Displays configuration information for control plane policy maps.

policy-map type control-plane

To enter the control plane policy map configuration mode, use the policy-map type control-plane command.

policy-map type control-plane policy-map-name

Syntax Description

policy-map-name

Name of the default control plane policy map. The name is alphanumeric, case sensitive, and has a maximum of 64 characters.

Command Default

None

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

In Cisco Nexus devices, you cannot create a user-defined Control Plane Policing (CoPP) policy map. The switch software includes a default control plane policy map, copp-system-policy-default, and one customized policy map, copp-system-policy-customized. You cannot add or remove classes from the default control-plane policy map. You can, however, add or remove classes to or from the copp-system-policy-customized control-plane policy map.

If you attempt to create a control plane policy with a name other than the default, you will see the following error message:

ERROR: Policy-map create failed

This command does not require a license.

Examples

This example shows how to enter the control plane policy map configuration mode:

switch# configure terminal

switch(config)# policy-map type control-plane copp-system-policy-customized

switch(config-pmap)#

This example shows the error message that appears when you create a control plane policy map other than the default control plane policy map:

switch# configure terminal

switch(config)# policy-map type control-plane PolicyMapA

ERROR: Policy-map create failed

switch(config)#

Related Commands

Command

Description

show policy-map type control-plane

Displays configuration information for control plane policy maps.

policy-map type network-qos

To create or modify a policy map and enter the policy map type network-qos configuration mode, use the policy-map type network-qos command. To remove a policy map, use the no form of this command.

policy-map type network-qos policy-map-name

no policy-map type network-qos policy-map-name

Syntax Description

policy-map-name

Name assigned to a type network-qos policy map. The name can be a maximum of 40 alphanumeric characters.

Command Default

None

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Use the service-policy command to assign policy maps to interfaces.

On a Cisco Nexus device, the switch software does not automatically attach the class-fcoe class map to a policy map. You can manually add the class-fcoe class to a policy map. On all other Cisco Nexus 5000 Series switches, this class is, by default, included in a policy map. On a Cisco Nexus device, you can remove the class-fcoe class from a policy map.

You can configure the qos-group of a class-fcoe class map on a Cisco Nexus device using the set qos-group command. The default qos-group value is 1.

Examples

This example shows how to create or modify a type network-qos policy map:

switch(config)# policy-map type network-qos my_policy1

switch(config-pmap-nq)#

This example shows how to remove a type network-qos policy map:

switch(config)# no policy-map type network-qos my_policy1

switch(config)

Related Commands

Command

Description

class type network-qos

References a type network-qos class map in a policy map.

description

Adds a description to a class map or policy map.

feature fcoe

Enables FCoE on the switch.

set qos-group

Assigns a QoS group identifier for a class of traffic.

show policy-map

Displays policy maps.

policy-map (type qos)

To create or modify a policy map and enter the policy map type qos configuration mode, use the policy-map command. To remove a QoS policy map, use the no form of this command.

policy-map [type qos] qos-policy-map-name

no policy-map [type qos] qos-policy-map-name

Syntax Description

type qos

(Optional) Specifies the type qos policy map.

qos-policy-map-name

Name assigned to a type qos policy map. The name can be a maximum of 40 alphanumeric characters.

Command Default

The software enters the policy map type qos configuration mode if you enter the policy-map command without specifying a type.

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Use the service-policy command to assign policy maps to interfaces.

On a Cisco Nexus device, the switch software does not automatically attach the class-fcoe class map to a policy map. You can manually add the class-fcoe class to a policy map. On all other Cisco Nexus 5000 Series switches, this class is, by default, included in a policy map. On a Cisco Nexus device, you can remove the class-fcoe class from a policy map.

You can configure the qos-group of a class-fcoe class map on a Cisco Nexus device using the set qos-group command. The default qos-group value is 1.

Examples

This example shows how to create or modify a type qos policy map:

switch(config)# policy-map my_policy1

switch(config-pmap-qos)#

This example shows how to remove a type qos policy map:

switch(config)# no policy-map my_policy1

Related Commands

Command

Description

class-map type qos

Configures a qos class map.

feature fcoe

Enables FCoE features on the switch.

service-policy

Attaches a policy map to an interface.

set dscp

Sets the DSCP value for the QoS traffic.

set precedence

Sets the IP precedence value for the QoS traffic.

set qos-group

Assigns a QoS group identifier for a class of traffic.

show policy-map

Displays policy maps.

policy-map type queuing

To create or modify a policy map and enter the policy map type queuing configuration mode, use the policy-map type queuing command. To remove a policy map, use the no form of this command.

policy-map type queuing queuing-policy-map-name

no policy-map type queuing queuing-policy-map-name

Syntax Description

queuing-policy-map-name

Name assigned to a type queuing policy map. The name can be a maximum of 40 alphanumeric characters.

Command Default

None

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Use the service-policy command to assign policy maps to interfaces.

On a Cisco Nexus device, the switch software does not automatically attach the class-fcoe class map to a policy map. You can manually add the class-fcoe class to a policy map. On all other Cisco Nexus 5000 Series switches, this class is, by default, included in a policy map. On a Cisco Nexus device, you can remove the class-fcoe class from a policy map.

You can configure the following on a class-fcoe class map:

- Bandwidth

The bandwidth value must be greater than zero (0).

- qos-group (on a Cisco Nexus device)

Note On a Cisco Nexus device, the default qos-group value is 1.

Examples

This example shows how to create or modify a queuing policy map:

switch(config)# policy-map type queuing my_policy1

switch(config-pmap-que)# class type queuing my_class1

switch(config-pmap-c-que)# bandwidth percent 75

switch(config-pmap-c-que)# exit

switch(config-pmap-que)#

This example shows how to remove a type queuing policy map:

switch(config)# no policy-map type queuing my_policy1

switch(config)#

Related Commands

Command

Description

bandwidth

Configures the interface bandwidth.

service-policy

Attaches a policy map to an interface.

set qos-group

Assigns a QoS group identifier for a class of traffic.

show policy-map

Displays policy maps.

priority

To assign a priority to a traffic class in a policy map, use the priority command. To remove the mapping, use the no form of this command.

priority

no priority

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Policy map type queuing class configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

When you configure a strict priority queue for a traffic class in a policy map, the priority class receives preference over other class queues. This queue is serviced before all other queues except queue zero (which carries control traffic, not data traffic).

Examples

This example shows how to map the traffic class to a strict priority queue:

switch(config)# policy-map type queuing my_policy1

switch(config-pmap-que)# class type queuing 8q2t-in-q4

switch(config-pmap-c-que)# priority

switch(config-pmap-que)#

Related Commands

Command

Description

show policy-map

Displays the policy maps.

priority (virtual Ethernet interface)

To assign a priority to a virtual Ethernet interface traffic class in a policy map, use the priority command. To remove the mapping, use the no form of this command.

priority veth-priority

no priority

Syntax Description

veth-priority

Virtual Ethernet interface priority. The range is from 0 to 65535.

Command Default

None

Command Modes

Virtual Ethernet interface configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Before you use this command, you must configure a virtual Ethernet interface by using the interface vethernet command.

When you configure a strict priority queue for a traffic class in a policy map, the priority class receives preference over other class queues. This queue is serviced before all other queues except queue zero (which carries control traffic, not data traffic).

Examples

This example shows how to configure the priority for a virtual Ethernet interface:

switch(config)# interface vethernet 10

switch(config-if)# priority

switch(config-if)#

Related Commands

Command

Description

interface vethernet

Configures a virtual Ethernet interface.

show policy-map

Displays the policy maps.

priority-flow-control

To set the priority-flow-control (PFC) mode for the selected interface, use the priority-flow-control command.

priority-flow-control mode {auto | on | off}

no priority-flow-control mode {auto | on | off}

Syntax Description

auto

Negotiates PFC capability.

on

Force-enables PFC.

off

Force-disables PFC.

Command Default

Auto

Command Modes

Interface configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can use this command on the following interfaces:

- Layer 2 interface

- Layer 3 interface

Note Use the no switchport command to configure an interface as a Layer 3 interface.

Examples

This example shows how to force-enable PFC on an interface:

switch# configure terminal

switch(config)# interface ethernet 1/2

switch(config-if)# priority-flow-control mode on

switch(config-if)#

This example shows how to force-disable PFC on an interface:

switch# configure terminal

switch(config)# interface ethernet 1/5

switch(config-if)# priority-flow-control mode off

switch(config-if)#

Related Commands

Command

Description

flowcontrol

Sets link-level flow control for the selected interface.

no switchport

Configures an interface as a Layer 3 routed interface.

show interface flowcontrol

Displays the detailed listing of the flow control settings on all interfaces.

show interface priority-flow-control

Displays the priority flow control details for a specified interface.

Q Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with Q.

queue-limit

To configure tail drop by setting queue limits on ingress queues, use the queue-limit command. To remove a queue limit, use the no form of this command.

queue-limit queue-size bytes

no queue-limit queue-size bytes

Syntax Description

queue-size

Queue size threshold (in bytes). The range is from 20480 to 204800. For the Cisco Nexus device, the range is from 20480 to 426880 bytes.

Command Default

None

Command Modes

Policy map type network-qos class configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can use this command to specify or modify the maximum number of packets the queue can hold for a class policy configured in a policy map. The system drops packets that exceed the configured queue-size threshold.

You can use this command only for network-qos class maps that do not have “pause” configured.

Examples

This example shows how to assign a queue limit to a policy map network-qos class:

switch(config)# policy-map type network-qos my_queue

switch(config-pmap-nq)# class type network-qos nqos_class

switch(config-pmap-nq-c)# queue-limit 20480 bytes

switch(config-pmap-nq-c)#

This example shows how to remove a queue limit from a policy map queuing class:

switch(config)# policy-map type network-qos my_queue

switch(config-pmap-nq)# class type network-qos nqos_class

switch(config-pmap-nq-c)# no queue-limit 20480 bytes

switch(config-pmap-nq-c)#

Related Commands

Command

Description

pause no-drop

Enables pause characteristics on a class referenced in a type network-qos policy map.

show policy-map

Displays policy maps.

S Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with S.

service-policy

To attach a policy map to an interface, use the service-policy command. To remove a service-policy from an interface, use the no form of this command.

service-policy {input | type {qos input | queuing {input | output}}} policy-map-name

no service-policy {input | type {qos input | queuing {input | output}}} policy-map-name

Syntax Description

input

Applies this policy map to packets coming into this interface.

type

Specifies whether the policy map is of type qos or queuing.

qos

Specifies a policy map of type qos.

queuing

Specifies a policy map of type queuing.

output

Applies this policy map to packets going out of this interface.

policy-map-name

Name of the policy map to attach to this interface. Only one policy map can be attached to the input and one to the output of a given interface for each of the policy type qos and queuing.

The policy map name can be a maximum of 40 alphanumeric characters.

Command Default

None

Command Modes

Interface configuration mode

Subinterface configuration mode

Vlan configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can attach one ingress and one egress type queuing policy map to an interface of type port, and port channel. Only one policy map can be attached to the input of a given interface for each of the policy type qos and queuing.

Examples

This example shows how to attach a queuing policy map to the ingress packets of a Layer 2 port interface:

switch# configure terminal

switch(config)# interface ethernet 2/1

switch(config-if)# service-policy type queuing input my_input_q_policy

switch(config-if)#

This example shows how to attach qos type policy maps to the incoming packets of a Layer 2 interface:

switch# configure terminal

switch(config)# system qos

switch(config-sys-qos)# service-policy type qos input my_policy1

switch(config-sys-qos)#

This example shows how to attach a qos type policy map named set-dscp to the incoming packets of a Layer 2 interface:

switch# configure terminal

switch(config)# policy-map type qos set-dscp

switch(config-pmap-qos)# class class-0

switch(config-pmap-c-qos)# set dscp ef

switch(config-pmap-c-qos)# exit

switch(config-pmap-qos)# class class-1-2

switch(config-pmap-c-qos)# set precedence 4

switch(config-pmap-c-qos)# exit

switch(config-pmap-qos)# exit

switch(config)# interface ethernet 2/1

switch(config-if)# service-policy type qos input set-dscp

switch(config-if)#

This example shows how to attach a queuing policy map to a Layer 3 interface:

switch# configure terminal

switch(config)# interface ethernet 1/5

switch(config-if)# no switchport

switch(config-if)# service-policy type queuing input my_input_q_policy

switch(config-if)#

Related Commands

Command

Description

no switchport

Configures an interface as a Layer 3 routed interface.

show policy-map interface brief

Displays all interfaces and VLANs with attached service policies in a brief format.

system qos

Configures a system policy.

service-policy (control-plane)

To attach a policy map to a control plane for aggregate control plane services, use the service-policy command.

service-policy input policy-map-name

Syntax Description

input

Applies the specified service policy to packets that are entering the control plane.

policy-map-name

Name of the control plane policy map to be attached. The name can be a maximum of 64 alphanumeric characters.

Command Default

None

Command Modes

Control-plane configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

After using the control-plane command, you should use the service-policy command to configure a quality of service (QoS) policy. This policy is attached to the control plane interface for aggregate control plane services, which can control the number or rate of packets that are going to the process level.

Examples

This example shows how to attach a control-plane policy map to the control plane:

switch# configure terminal

switch(config)# ip access-list ipv4-acl-telnet

switch(config-acl)# permit tcp 10.23.0.0/16 10.176.0.0/16

switch(config-acl)# exit

switch(config)# class-map type control-plane telnet-class

switch(config-cmap)# match access-group name ipv4-acl-telnet

switch(config-cmap)# exit

switch(config)# policy-map type control-plane copp-system-policy

switch(config-pmap)# class telnet-class

switch(config-pmap-c)# police 1000

switch(config-pmap-c)# exit

switch(config-pmap)# exit

switch(config)# control-plane

switch(config-cp)# service-policy input copp-system-policy

switch(config-cp)# exit

switch(config)#

Related Commands

Command

Description

control-plane

Enters control-plane configuration mode.

policy-map type control-plane

Creates or modifies a control plane policy map.

show policy-map control-plane

Displays the configuration of a class or all classes for the policy map of a control plane.

service-policy (system qos)

To attach a policy map to a system policy, use the service-policy command. To remove a service policy from a system policy, use the no form of this command.

service-policy {input | type {network-qos | qos input | queuing {input | output}}} policy-map-name

no service-policy {input | type {network-qos | qos input | queuing {input | output}}} policy-map-name

Syntax Description

input

Applies this policy map to packets coming into this interface.

type

Specifies whether the policy map is of type network-qos, qos, or queuing.

network-qos

Specifies a policy map of type network-qos.

qos

Specifies a policy map of type qos.

queuing

Specifies a policy map of type queuing.

output

Applies this policy map to packets going out of this interface.

policy-map-name

Name of the policy map to attach to this interface. The policy map name can be a maximum of 40 alphanumeric characters.

Command Default

None

Command Modes

System QoS configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to attach a queuing policy map to the system policy:

switch# configure terminal

switch(config)# system qos

switch(config-sys-qos)# service-policy type queuing input my_input_q_policy

switch(config-sys-qos)#

Related Commands

Command

Description

show policy-map

Displays policy maps.

system qos

Configures a system policy.

service-policy (virtual Ethernet interface)

To attach a policy map to a virtual Ethernet interface, use the service-policy command. To remove a service policy from a virtual Ethernet interface, use the no form of this command.

service-policy {input | type {qos input | queuing {input | output}}} policy-map-name

no service-policy {input | type {qos input | queuing {input | output}}} policy-map-name

Syntax Description

input

Applies this policy map to packets coming into this virtual interface.

type

Specifies the policy map of type qos.

qos

Specifies a policy map of type qos.

queuing

Specifies a policy map of type queuing.

input

Applies the policy map to packets coming into this interface.

output

Applies the policy map to packets going out of this interface.

policy-map-name

Name of the policy map to attach to this interface. Only one policy map can be attached to the input of a given interface for the policy type qos.

The policy map name can be a maximum of 40 alphanumeric characters.

Command Default

None

Command Modes

Virtual Ethernet interface configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can attach one ingress and one egress type queuing policy map to an interface of type port and port channel. Only one policy map can be attached to the input of a given interface for each of the policy type qos and queuing.

Note For more information on using service policies, see the Quality of Service Guide for your platform.

Examples

This example shows how to attach a qos policy map to the ingress packets of a virtual Ethernet interface:

switch# configure terminal

switch(config)# interface vethernet 12

switch(config-if)# service-policy type qos input my_veth_policy

switch(config-if)#

This example shows how to attach a queuing policy that is configured for traffic shaping to the incoming packets of a virtual Ethernet interface:

switch(config)# policy-map type queuing p2

switch(config-pmap-que)# class type queuing class-default

switch(config-pmap-c-que)# shape 30 kbps 3000

switch(config-pmap-c-que)# exit

switch(config-pmap-que)# exit

switch(config)# interface vethernet 1

switch(config-if)# service-policy type queuing input p2

switch(config-if)#

Related Commands

Command

Description

interface vethernet

Configures a virtual Ethernet interface.

policy-map type queuing

Configures a queuing policy map.

show policy-map interface brief

Displays all interfaces and VLANs with attached service policies in a brief format.

system qos

Configures a system policy.

set cos (policy map type network-qos)

To assign a class of service (CoS) value for a class of traffic in a type network-qos policy map, use the set command. To remove the assigned value from the class, use the no form of this command.

set cos cos-value

no set cos cos-value

Syntax Description

cos-value

CoS value to assign for this class of traffic. The range is from 0 to 7.

Command Default

None

Command Modes

Policy map type network-qos class configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can use this command only on type network-qos policies that are attached to egress ports.

Layer 3 topologies you must configure each qos-group in the network-qos policy with a unique cos value.

Examples

This example shows how to assign a CoS value for a class of traffic in a type network-qos policy map:

switch(config)# policy-map type network-qos my_policy1

switch(config-pmap-nq)# class type network-qos traffic_class2

switch(config-pmap-nq-c)# set cos 3

switch(config-pmap-nq-c)#

This example shows how to remove the assignment of CoS for a class of traffic in a type network-qos policy map:

switch(config)# policy-map type network-qos my_policy1

switch(config-pmap-nq)# class type network-qos traffic_class2

switch(config-pmap-nq-c)# no set cos 3

switch(config-pmap-nq-c)#

Related Commands

Command

Description

show policy-map

Displays policy maps.

set dscp

To assign a Differentiated Services Code Point (DSCP) value for a traffic class in a type qos policy map on a Cisco Nexus 5548 switch, use the set dscp command. To remove a previously set DSCP value, use the no form of this command.

set dscp dscp-value

no set dscp dscp-value

Syntax Description

dscp-value

DSCP value or parameter to assign for this class of traffic. Valid values are from 0 to 63.

For a list of standard DSCP values, see Table 1.

Command Default

None

Command Modes

Policy map type qos configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Marking is a method that you use to modify the QoS fields of the incoming and outgoing packets.

You can set the value of standard QoS fields IP precedence, DSCP, and Class of Service (CoS), and internal labels that can be used in subsequent actions. Marking is used to identify the traffic type for use in policing, queuing, and scheduling traffic (only CoS is used in scheduling).

Use this command to classify the traffic based on the DSCP packet header field (either IPv4 or IPv6). When you set the DSCP value for a packet, make sure that you use a traffic class other than the class-default system class. For example, qos-group x, where x is any value from 1 to 5.

Note You cannot set the DSCP packet header field (either IPv4 or IPv6) if the traffic is in the class-default system class (qos-group 0).

You can set the DSCP value in the six most significant bits of the DiffServ field of the IP header to a specified value. You can enter numeric values from 0 to 63, as well as the standard DSCP values shown in Table 1.

If you set the values for more than two IP header fields (either IPv4 or IPv6), an error similar to the following appears:

ERROR: Only 2 sets out of qos-group/cos/dscp/precedence/discard-class are allowed. Please remove other set action before applying this one.

Note You can set DSCP or IP precedence but you cannot set both values because they modify the same field in the IP packet.

After you set the DSCP value, for the QoS policy map to work correct and create the specified QoS groups, make sure that you attach the QoS policy map to a system policy, then define a network-qos policy map and attach it to the system policy. Make sure that the QoS group of the QoS policy map matches that of the of the network-qos policy.

Examples

This example shows how to set the DSCP value for a QoS policy:

switch(config)# policy-map type qos my_policy

switch(config-pmap-qos)# class type qos my_class

switch(config-pmap-c-qos)# set dscp cs6

switch(config-pmap-c-qos)# set qos-group 2

switch(config-pmap-c-qos)# exit

switch(config-pmap-qos)# exit

switch(config)# system qos

switch(config-sys-qos)# service-policy type qos input my_policy

switch(config-sys-qos)# exit

switch(config)# class-map type network-qos nqos_class

switch(config-cmap-nq)# match qos-group 2

switch(config-cmap-nq)# exit

switch(config)# policy-map type network-qos nqos_policy

switch(config-pmap-nq)# class type network-qos nqos_class

switch(config-pmap-nq-c)# exit

switch(config-pmap-nq)# exit

switch(config)# system qos

switch(config-sys-qos)# service-policy type network-qos nqos_policy

switch(config-sys-qos)# exit

switch(config)#

Related Commands

Command

Description

copy running-config startup-config

Copies the running configuration to the startup configuration file.

show policy-map type qos

Displays the QoS policy maps.

show running-config ipqos

Displays the QoS running configuration.

set precedence

To set the precedence value in an IP header (either IPv4 or IPv6) for a class of traffic in a type qos policy map on a Cisco Nexus 5548 switch, use the set precedence command. To leave the precedence value unchanged for the class, use the no form of this command.

set precedence precedence-value

no set precedence precedence-value

Syntax Description

precedence-value

IP precedence value to assign for this class of traffic. Valid values are from 0 to 7.

For a list of standard precedence values, see Table 2.

Command Default

None

Command Modes

Policy map type qos configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Marking is a method that you use to modify the QoS fields of the incoming and outgoing packets.

You can set the value of standard QoS fields IP precedence, DSCP, and Class of Service (CoS), and internal labels that can be used in subsequent actions. Marking is used to identify the traffic type for use in policing, queuing, and scheduling traffic (only CoS is used in scheduling).

Use this command to classify the traffic based on the IP precedence packet header field. When you set the IP precedence value for a packet, make sure that you use a traffic class other than the class-default system class. For example, qos-group x, where x is any value from 1 to 5.

Note You cannot set the IP precedence packet header field if the traffic is in the class-default system class (qos-group 0).

If you set the values for more than two IP header fields, you see the following error message:

ERROR: Only 2 sets out of qos-group/cos/dscp/precedence/discard-class are allowed. Please remove other set action before applying this one.

Note You can set DSCP or IP precedence but you cannot set both values because they modify the same field in the IP packet.

After you set the IP precedence value, for the QoS policy map to work correct and create the specified QoS groups, make sure that you attach the QoS policy map to a system policy, then define a network-qos policy map and attach it to the system policy. Make sure that the QoS group of the QoS policy map matches that of the of the network-qos policy.

Examples

This example shows how to set the IP precedence value for a QoS policy:

switch(config)# policy-map type qos my_policy

switch(config-pmap-qos)# class type qos my_class

switch(config-pmap-c-qos)# set precedence 5

switch(config-pmap-c-qos)# set qos-group 2

switch(config-pmap-c-qos)# exit

switch(config-pmap-qos)# exit

switch(config)# system qos

switch(config-sys-qos)# service-policy type qos input my_policy

switch(config-sys-qos)# exit

switch(config)# class-map type network-qos nqos_class

switch(config-cmap-nq)# match qos-group 2

switch(config-cmap-nq)# exit

switch(config)# policy-map type network-qos nqos_policy

switch(config-pmap-nq)# class type network-qos nqos_class

switch(config-pmap-nq-c)# exit

switch(config-pmap-nq)# exit

switch(config)# system qos

switch(config-sys-qos)# service-policy type network-qos nqos_policy

switch(config-sys-qos)# exit

switch(config)#

Related Commands

Command

Description

copy running-config startup-config

Copies the running configuration to the startup configuration file.

show policy-map type qos

Displays the QoS policy maps.

show running-config ipqos

Displays the QoS running configuration.

show startup-config ipqos

Displays the QoS configuration stored in the startup file.

set qos-group

To assign the QoS group identifier for a class of traffic in a type qos policy map, use the set qos-group command. To remove the assigned value from the class, use the no form of this command.

set qos-group qos-group-value

no set qos-group qos-group-value

Syntax Description

qos-group-value

QoS group value to assign for this class of traffic. The range is from 1 to 5 for a Cisco Nexus device. On a Cisco Nexus device, the default is 1.

Command Default

1 on a Cisco Nexus 5548 switch.

Command Modes

Policy map type qos class configuration

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can set the QoS group identifier value only in ingress policies. You can set a maximum of 5 QoS groups in ingress policies.

If you set the values for more than two IP header fields in a policy map class, an error message similar to the following appears:

ERROR: Only 2 sets out of qos-group/cos/dscp/precedence/discard-class are allowed. Please remove other set action before applying this one.

Examples

This example shows how to assign a QoS group identifier for a class of traffic in a type qos policy map:

switch(config)# policy-map my_policy

switch(config-pmap-qos)# class my_class

switch(config-pmap-c-qos)# set qos-group 3

switch(config-pmap-c-qos)#

Related Commands

Command

Description

copy running-config startup-config

Copies the running configuration to the startup configuration file.

show policy-map type qos

Displays the QoS policy maps.

show running-config ipqos

Displays the QoS running configuration.

show startup-config ipqos

Displays the QoS configuration stored in the startup file.

shape (virtual Ethernet interface)

To configure shaping on an egress queue to impose a maximum rate on it, use the shape command. To remove a shaping configuration, use the no form of this command.

shape target-rate {kbps | mbps | gbps} burst-size

no shape target-rate {kbps | mbps | gbps} burst-size

Syntax Description

target-rate

Traffic rate. The range is from 1 to 10,000,000,000.

kbps

Specifies the units of 1000 bits per second.

mbps

Specifies the units of megabits per second.

gbps

Specifies the units of gigabits per second.

burst-size

Burst size in bytes. The range is from 1500 to 65535.

Command Default

None

Command Modes

Policy map type queuing class configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Traffic shaping is supported only on virtual Ethernet interfaces.

Shaping rate limits the traffic with a specified rate. You can configure shaping only in the ingress direction. All traffic on the virtual Ethernet interface is rate limited to the given shaping rate.

Note If you configure shaping, you cannot configure priority in the same policy map.

This command does not require a license.

Examples

This example shows how to configure shaping on a queuing policy map and apply the policy to a virtual Ethernet interface:

switch# configure terminal

switch(config)# policy-map type queuing p2

switch(config-pmap-que)# class type queuing class-default

switch(config-pmap-c-que)# shape 30 kbps 3000

switch(config-pmap-c-que)# exit

switch(config-pmap-que)# exit

switch(config)# interface vethernet 1

switch(config-if)# service-policy type queuing input p2

switch(config-if)#

Related Commands

Command

Description

service-policy (virtual Ethernet interface)

Applies a policy map to a virtual Ethernet interface.

show policy-map

Displays the policy map information.

system jumbomtu

To define the upper bound of any maximum transmission unit (MTU) in the system, use the system jumbomtu command.

system jumbomtu [value]

Syntax Description

value

Jumbomtu value. The range is from 2158 to 9216.

Command Default

9216 bytes

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to define the upper bound of any MTU in the system:

switch(config)# system jumbomtu 9216

switch(config)#

Related Commands

Command

Description

show interface

Displays the jumbo MTU frames sent and received on the specified interface.

system qos

To configure a system policy, use the system qos command.

system qos

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to configure a system qos to apply a queuing policy to all interfaces in the system:

switch(config)# system qos

switch(config-sys-qos)#

Related Commands

Command

Description

service-policy

Associates the system class policy-map to the service policy for the system.

Show Commands

This chapter describes the Cisco NX-OS quality of service (QoS) show commands.

show class-map type control-plane

To display control plane class map information, use the show class-map type control-plane command.

show class-map type control-plane [class-map-name]

Syntax Description

class-map-name

(Optional) Name of the control plane class map. The name is alphanumeric and case sensitive. The maximum length is 64 characters.

Command Default

None

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display control plane class map information:

switch# show class-map type control-plane

class-map type control-plane match-any copp-system-class-arp

match protocol arp

class-map type control-plane match-any copp-system-class-bgp

match protocol bgp

class-map type control-plane match-any copp-system-class-bridging

match protocol bridging

class-map type control-plane match-any copp-system-class-cdp

match protocol cdp

class-map type control-plane match-any copp-system-class-default

match protocol default

<--Output truncated-->

switch#

Related Commands

Command

Description

class-map type control-plane

Creates or configures a control plane class map.

show class-map type network-qos

To display type network-qos class maps, use the show class-map type network-qos command.

show class-map type network-qos [class-map-name]

Syntax Description

class-map-name

Name of the class map. The name can be a maximum of 40 alphanumeric characters.

Command Default

Displays all type network-qos class maps if no class map name is specified.

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

If you do not specify the type, the command displays all the class maps configured in the system.

Examples

This example shows how to display all type network-qos class maps:

switch(config)# show class-map type network-qos

Type network-qos class-maps

==============================

class-map type network-qos s1

match qos-group 2

class-map type network-qos s2

match qos-group 3

class-map type network-qos s3

match qos-group 4

class-map type network-qos s4

match qos-group 5

class-map type network-qos cu1

match qos-group 2

class-map type network-qos cu2

match qos-group 3

class-map type network-qos cu3

match qos-group 4

class-map type network-qos cu4

match qos-group 5

class-map type network-qos new

match qos-group 2

class-map type network-qos class7

match qos-group 5

class-map type network-qos class-0

match qos-group 2

class-map type network-qos ip-based

match qos-group 5

class-map type network-qos class-1-2

match qos-group 3

class-map type network-qos class-4-7

match qos-group 4

class-map type network-qos cos-based

match qos-group 2

class-map type network-qos class-fcoe

match qos-group 1

class-map type network-qos class-flood

match qos-group 2

class-map type network-qos cos-based-3

match qos-group 3

class-map type network-qos cos-based-4

match qos-group 4

class-map type network-qos class-default

match qos-group 0

class-map type network-qos class-multicast

class-map type network-qos class-ip-multicast

match qos-group 5

switch(config)#

Related Commands

Command

Description

class-map

Creates or modifies a class map.

show class-map type qos

To display type qos class maps, use the show class-map type qos command.

show class-map type qos [class-map-name]

Syntax Description

class-map-name

Named class map. The name class-default is reserved. The name can be a maximum of 40 alphanumeric characters.

Command Default

Displays all type qos class maps if no class map name is specified.

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display all type qos class maps on a switch:

switch(config)# show class-map type qos

Type qos class-maps

===================

class-map type qos s1

match cos 0

class-map type qos s2

match protocol ldp

match ip rtp 2000

match protocol dhcp

match protocol arp

class-map type qos s3

match access-group name mac

class-map type qos s4

match access-group name ipv4

class-map type qos cp1

match precedence 4-5

match cos 0,4

match dscp 4

match protocol ldp

match protocol arp

class-map type qos cp2

match ip rtp 2000

match cos 0

class-map type qos cp3

match access-group name mac

class-map type qos cp5

class-map type qos cq1

match protocol ldp

match precedence 7

match cos 0

class-map type qos cq2

match protocol ldp

match cos 1-2

class-map type qos cq3

match access-group name mac

class-map type qos cq4

match access-group name ipv4-1

class-map type qos cq5

match access-group name ipv6-based

class-map type qos p1.1

match cos 7

class-map type qos p1.2

match protocol ldp

match ip rtp 2000-6001,10000-20000,60000-65535

match dscp 1

match protocol dhcp

match protocol arp

match precedence 0-7

class-map type qos p1.3

match access-group name mac

class-map type qos p1.4

match access-group name ipv4

class-map type qos p2.1

match cos 0,7

class-map type qos p2.2

match protocol ldp

match ip rtp 2000-6000,6002,10000-20000,60000-65535

match dscp 2

match protocol dhcp

match protocol arp

match precedence 0-7

class-map type qos p2.3

match access-group name mac

class-map type qos p2.4

match access-group name ipv4

class-map type qos p3.1

match cos 0,7

class-map type qos p3.2

match protocol ldp

match ip rtp 2000-6000,6003,10000-20000,60000-65535

match dscp 3

match protocol dhcp

match protocol arp

match precedence 0-7

class-map type qos p3.3

match access-group name mac

class-map type qos p3.4

match access-group name ipv4

class-map type qos p4.1

match cos 0,7

class-map type qos p4.2

match protocol ldp

match ip rtp 2000-6000,6004,10000-20000,60000-65535

match dscp 4

match protocol dhcp

match protocol arp

match precedence 0-7

class-map type qos p4.3

match access-group name mac

class-map type qos p4.4

match access-group name ipv4

class-map type qos p5.1

match cos 0,7

class-map type qos p5.2

match protocol ldp

match ip rtp 2000-6000,6005,10000-20000,60000-65535

match dscp 5

match protocol dhcp

match protocol arp

match precedence 0-7

class-map type qos p5.3

match access-group name mac

class-map type qos p5.4

match access-group name ipv4

class-map type qos p6.1

match cos 0,7

class-map type qos p6.2

match protocol ldp

match ip rtp 2000-6000,6006,10000-20000,60000-65535

match dscp 6

match protocol dhcp

match protocol arp

match precedence 0-7

class-map type qos p6.3

match access-group name mac

class-map type qos p6.4

match access-group name ipv4

class-map type qos p7.1

match cos 0,7

class-map type qos p7.2

match protocol ldp

match ip rtp 2000-6000,6007,10000-20000,60000-65535

match dscp 7

match protocol dhcp

match protocol arp

match precedence 0-7

class-map type qos p7.3

match access-group name mac

class-map type qos p7.4

match access-group name ipv4

class-map type qos p8.1

match cos 0,7

class-map type qos p8.2

match protocol ldp

match ip rtp 2000-6000,6008,10000-20000,60000-65535

match dscp 8

match protocol dhcp

match protocol arp

match precedence 0-7

class-map type qos p8.3

match access-group name mac

class-map type qos p8.4

match access-group name ipv4

class-map type qos p9.1

match cos 0,7

class-map type qos p9.2

match protocol ldp

match ip rtp 2000-6000,6009,10000-20000,60000-65535

match dscp 9

match protocol dhcp

match protocol arp

match precedence 0-7

class-map type qos p9.3

match access-group name mac

class-map type qos p9.4

match access-group name ipv4

class-map type qos class-0

match cos 0

class-map type qos class-6

match cos 6

class-map type qos class-7

match cos 7

class-map type qos clsas-0

class-map type qos cos-6-7

match cos 7

class-map type qos ip-based

match access-group name ip-based

class-map type qos acl-based

match access-group name ipPacl

class-map type qos class-1-2

match cos 1-2

class-map type qos class-4-5

match cos 4-5

class-map type qos class-4-6

match cos 5

class-map type qos class-4-7

match cos 5,7

class-map type qos class-405

class-map type qos cos-based

class-map type qos mac-based

match access-group name foo

class-map type qos udp-based

match access-group name ip-based

class-map type qos class-fcoe

match cos 3

class-map type qos class-flood

class-map type qos class-default

match any

class-map type qos class-all-flood

match all flood

class-map type qos class-ip-multicast

match ip multicast

switch(config)#

This example shows how to display a specific class map:

switch# show class-map type qos class-4-6

Type qos class-maps

===================

class-map type qos class-4-6

match cos 5

switch#

This example shows how to display all type qos class maps:

switch# show class-map type qos

Type qos class-maps

===================

class-map type qos match-any class-fcoe

match cos 3

class-map type qos match-any class-default

match any

class-map type qos match-any class-all-flood

match all flood

class-map type qos match-any class-ip-multicast

match ip multicast

switch#

Related Commands

Command

Description

class-map

Creates or modifies a class map.

show class-map type queuing

To display type queuing class maps, use the show class-map type queuing command.

show class-map type queuing [class-map-name]

Syntax Description

class-map-name

Named class map. The name can be a maximum of 40 alphanumeric characters.

Command Default

Displays all type queuing class maps if no class map name is specified.

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display all type queuing class maps on a switch:

switch(config)# show class-map type queuing

Type queuing class-maps

=======================

class-map type queuing s1

match qos-group 2

class-map type queuing s2

match qos-group 3

class-map type queuing s3

match qos-group 4

class-map type queuing s4

match qos-group 5

class-map type queuing cq1

match qos-group 2

class-map type queuing cq2

match qos-group 3

class-map type queuing cq3

match qos-group 4

class-map type queuing cq4

match qos-group 5

class-map type queuing pq1

class-map type queuing cqe1

match qos-group 2

class-map type queuing cqe2

match qos-group 3

class-map type queuing cqe3

match qos-group 4

class-map type queuing cqe4

match qos-group 5

class-map type queuing p1.1

match qos-group 2

class-map type queuing p1.2

match qos-group 3

class-map type queuing p1.3

match qos-group 4

class-map type queuing p1.4

match qos-group 5

class-map type queuing p2.1

match qos-group 2

class-map type queuing p2.2

match qos-group 3

class-map type queuing p2.3

match qos-group 4

class-map type queuing p2.4

match qos-group 5

class-map type queuing p3.1

match qos-group 2

class-map type queuing p3.2

match qos-group 3

<--Output truncated-->

switch(config)#

This example shows how to display all type queuing class maps:

switch# show class-map type queuing

Type queuing class-maps

=======================

class-map type queuing class-fcoe

match qos-group 1

class-map type queuing class-default

match qos-group 0

class-map type queuing class-all-flood

match qos-group 2

class-map type queuing class-ip-multicast

match qos-group 2

switch#

Related Commands

Command

Description

class-map

Creates or modifies a class map.

show copp status

To display the Control Plane Policing (CoPP) configuration status, use the show copp status command.

show copp status

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Any configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the CoPP configuration status information:

switch# show copp status

Last Config Operation: class class-default

Last Config Operation Timestamp: 05:06:14 UTC Jan 1 2013

Last Config Operation Status: Success

Policy-map attached to the control-plane: copp-system-policy-default

switch#

Related Commands

Command

Description

clear copp statistics

Clears the CoPP statistics.

show running-config copp

Displays CoPP configuration information in the running configuration.

show interface flowcontrol

To display the detailed listing of the flow control settings on all interfaces, use the show interface flowcontrol command.

show interface flowcontrol [module number]

Syntax Description

module number

(Optional) Displays flow control settings on all interfaces on a specified module. The module number range is from 1 to 3.

Command Default

None

Command Modes

EXEC mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can use this command to display the flow control information for the following interfaces:

- Layer 2 interface

- Layer 3 interface

Note Use the no switchport command to configure an interface as a Layer 3 interface, and then use the flowcontrol command to configure flow control for the interface.

Examples

This example shows how to display the flow control settings on all interfaces on a switch:

switch# show interface flowcontrol

--------------------------------------------------------------------------------

Port Send FlowControl Receive FlowControl RxPause TxPause

admin oper admin oper

--------------------------------------------------------------------------------

Eth1/1 off off off off 0 0

Eth1/2 off off off off 0 0

Eth1/3 off off off off 0 0

Eth1/4 off off off off 0 0

Eth1/5 off off off off 0 0

Eth1/6 off off off off 0 0

Eth1/7 off off off off 0 0

Eth1/8 off off off off 0 0

Eth1/9 off off off off 0 0

Eth1/10 off off off off 0 0

Eth1/11 off off off off 0 0

--More--

switch#

show hardware profile latency monitor

To display switch latency statistics for egress and ingress port pairs, use the show hardware profile latency monitor command.

show hardware profile latency monitor interface ethernet egress-interface-slot/port interface ethernet ingress-interface-slot/port

Syntax Description

interface

Displays the statistics for the specified interface.

ethernet egress-interface-slot/port

Specifies a single egress Ethernet interface and its slot number and port number. The slot number is from 1 to 255. The port number is from 1 to 128.

ethernet ingress-interface-slot/port

Specifies a single ingress Ethernet interface and its slot number and port number. The slot number is from 1 to 255. The port number is from 1 to 128.

Command Default

None

Command Modes

Any configuration mode

Command History

Release

Modification

7.0(0)N1(1)

This command was introduced.

Usage Guidelines

This command does not require a license. The ASIC reports a high latency value when the number of packets for a given latency range is monitored using the histograms or when the maximum latency value is monitored in the instantaneous mode. The maximum latency value is approximately 0.4 sec, which is incorrect. Ignore the value displayed because this is an unexpected behavior and does not have any functional impact on the switch.

Examples

The following example shows switch latency monitoring configuration and statistics information when instantaneous mode monitoring is enabled:

switch# show hardware profile latency monitor interface ethernet 1/1 interface ethernet 1/2-3

--------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/2 Mode: Inst

--------------------------------------------------------------------------------

| | Minimum | Maximum | Average |

--------------------------------------------------------------------------------

| cnt | 0 | 0| 0|

---------------------------------------------------------------------------------

---------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/3 Mode: Inst

--------------------------------------------------------------------------------

| | Minimum | Maximum | Average |

--------------------------------------------------------------------------------

| cnt | 0 | 0| 0|

--------------------------------------------------------------------------------

The following example shows switch latency monitoring configuration and statistics information when instantaneous mode monitoring is enabled:

switch# show hardware profile latency monitor interface ethernet 2/3 interface ethernet 2/2

--------------------------------------------------------------------------------

Egress Port: Ethernet2/3 Ingress Port: Ethernet2/2 Mode: Inst

--------------------------------------------------------------------------------

| | Minimum | Maximum | Average |

--------------------------------------------------------------------------------

| cnt | 736 | 463128320 | 904 |

--------------------------------------------------------------------------------

Note Ignore the maximum value because it does not have any functional impact on the switch.

The following example shows switch latency monitoring configuration and statistics information when linear histogram mode monitoring is enabled:

switch# show hardware profile latency monitor interface ethernet 1/1 interface ethernet 1/2

--------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/2 Mode: Linear Histogram

--------------------------------------------------------------------------------

| Range| 800-840| 840-880| 880-920| 920-960|

--------------------------------------------------------------------------------

| cnt | 0| 0| 0| 0|

--------------------------------------------------------------------------------

The following example shows switch latency monitoring configuration and statistics information when linear histogram mode monitoring is enabled:

switch# show hardware profile latency monitor interface ethernet 1/1 interface ethernet 1/9

----------------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/9 Mode: Linear Histogram

----------------------------------------------------------------------------------------

|Range| 463120000-463124000|463124000-463128000|463128000-463132000|463132000-463136000|

----------------------------------------------------------------------------------------

| cnt| 0 | 0 | 35 | 0 |

----------------------------------------------------------------------------------------

Note Ignore the ranges with high values because they do not have any functional impact on the switch.

The following example shows switch latency monitoring configuration and statistics information when exponential histogram mode monitoring is enabled:

switch# show hardware profile latency monitor interface ethernet 1/1 interface ethernet 1/3

--------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/3 Mode: Exp Histogram

--------------------------------------------------------------------------------

| Range| 840-880| 880-960| 960-1120| 1120-1440|

--------------------------------------------------------------------------------

| cnt | 0| 0| 0| 0|

-------------------------------------------------------------------------------

The following example shows switch latency monitoring configuration and statistics information when custom histogram mode monitoring is enabled:

switch# show hardware profile latency monitor interface ethernet 1/1 interface ethernet 1/5

--------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/5 Mode: Custom Histogram

--------------------------------------------------------------------------------

| Range| 840 <= Latency < 2000| 840 > Latency >= 2000|

--------------------------------------------------------------------------------

| cnt | 0| 0|

--------------------------------------------------------------------------------

The following example shows switch latency monitoring configuration and statistics information when a range of ingress interfaces are enabled:

switch# show hardware profile latency monitor interface ethernet 1/1 interface ethernet 1/2-5

--------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/2 Mode: Inst

--------------------------------------------------------------------------------

--------------------------------------------------------------------------------

| | Minimum | Maximum | Average |

--------------------------------------------------------------------------------

| cnt | 0 | 0| 0|

--------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/3 Mode: Inst

--------------------------------------------------------------------------------

| | Minimum | Maximum | Average |

--------------------------------------------------------------------------------

| cnt | 0 | 0| 0|

--------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/4 Mode: Inst

--------------------------------------------------------------------------------

| | Minimum | Maximum | Average |

--------------------------------------------------------------------------------

| cnt | 0 | 0| 0|

--------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/5 Mode: Exp Histogram

--------------------------------------------------------------------------------

| Range| 48-96| 96-129| 129-384| 384-768|

--------------------------------------------------------------------------------

| cnt | 0| 0| 0| 0|

-------------------------------------------------------------------------------

The following example shows switch latency monitoring configuration and statistics information when a range of ingress and egress interfaces are enabled:

switch# show hardware profile latency monitor interface ethernet 1/1-2 interface ethernet 1/2-3

--------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/2 Mode: Inst

--------------------------------------------------------------------------------

| | Minimum | Maximum | Average |

--------------------------------------------------------------------------------

| cnt | 0 | 0| 0|

--------------------------------------------------------------------------------

Egress Port: Ethernet1/1 Ingress Port: Ethernet1/3 Mode: Inst

--------------------------------------------------------------------------------

| | Minimum | Maximum | Average |

--------------------------------------------------------------------------------

| cnt | 0 | 0| 0|

--------------------------------------------------------------------------------

Egress Port: Ethernet1/2 Ingress Port: Ethernet1/2 Mode: Inst

--------------------------------------------------------------------------------

| | Minimum | Maximum | Average |

--------------------------------------------------------------------------------

| cnt | 0 | 0| 0|

--------------------------------------------------------------------------------

Egress Port: Ethernet1/2 Ingress Port: Ethernet1/3 Mode: Inst

--------------------------------------------------------------------------------

| | Minimum | Maximum | Average |

--------------------------------------------------------------------------------

| cnt | 0 | 0| 0|

--------------------------------------------------------------------------------

Related Commands

Command

Description

clear hardware profile latency monitor

Clears switch latency monitoring statistics.

hardware profile latency monitor base

Specifies the histogram base value to construct switch latency monitoring histograms.

packet latency interface

Enables switch latency histogram monitoring.

show hardware profile tcam feature qos

To display the the limits of the QoS TCAMs, use the show hardware profile tcam feature-qos command.

show hardware profile tcam feature qos tcam-size

Syntax Description

tcam-size

Interface QoS TCAM limit. The tcam-size can be from 7- 446 entries.

Command Default

None

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

No interface policy entry should be present after the interface_qos limit in the QoS region of any TCAM.

Examples

This example shows how to set the interface QoS TCAM limit to 20 entries:

switch(config)# configue terminal

switch(config)# hardware profile tcam feature interface-qos limit 20

switch(config)# show hardware profile tcam feature qos

Feature Limit

--------------------------------------------------------------------------------

Interface 20

vlan-qos + global-qos 428

switch(config)# copy running-config startup-config

Related Commands

Command

Description

hardware profile tcam feature interface-qos limit

Configures the QoS TCAM limit

show hardware internal bigsur all-ports qos-drop-history brief

To display the number of Ingress QoS packet drops that are associated with a timestamp, use show hardware internal bigsur all-ports qos-drop-history brief in EXEC mode.

show hardware internal bigsur all-ports qos-drop-history brief {all | unicast | multicaste}

Syntax Description

all

Specifies the qos-drop-history brief of type all.

unicast

Specifies the qos-drop-history brief of type unicast

multicast

Specifies the qos-drop-history brief of type multicast

Command Default

None

Command Modes

EXEC mode

Command History

Release

Modification

7.2(0)N1(1)

This command was introduced.

Examples

This example shows the number of Ingress all packet drops with timestamp for QoS-drop-history brief:

switch# show hardware internal bigsur all-ports qos-drop-history brief all

QoS all drops history

+-------------+------------+------------+------------+------------+------------+

| port | 5sec | 10sec | 60sec | 5min | 1hr |

+-------------+------------+------------+------------+------------+------------+

sup-eth1| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

sup-eth2| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/1| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/2| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/3| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/4| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/5| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/6| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/7| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/8| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/9| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/10| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/11| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/12| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/13| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/14| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/15| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/16| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/17| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/18| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/19| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/20| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/21| 0| 0| 0| 0| 0|

This example shows the number of Ingress multicast packet drops with timestamp for QoS-drop-history brief:

switch# show hardware internal bigsur all-ports qos-drop-history brief multicast

QoS multicast drop history

+-------------+------------+------------+------------+------------+------------+

| port | 5sec | 10sec | 60sec | 5min | 1hr |

+-------------+------------+------------+------------+------------+------------+

sup-eth1| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

sup-eth2| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/1| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/2| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/3| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/4| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/5| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/6| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/7| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/8| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/9| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/10| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/11| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/12| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/13| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/14| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/15| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/16| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/17| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/18| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/19| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/20| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/21| 0| 0| 0| 0| 0|

This example shows the number of Ingress unicast packet drops with timestamp for QoS-drop-history brief:

switch# show hardware internal bigsur all-ports qos-drop-history brief unicast

QoS unicast drop history

+-------------+------------+------------+------------+------------+------------+

| port | 5sec | 10sec | 60sec | 5min | 1hr |

+-------------+------------+------------+------------+------------+------------+

sup-eth1| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

sup-eth2| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/1| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/2| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/3| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/4| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/5| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/6| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/7| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/8| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/9| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/10| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/11| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/12| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/13| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/14| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/15| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/16| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/17| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/18| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/19| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/20| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Ethernet1/21| 0| 0| 0| 0| 0|

Related Commands

Command

Description

show hardware internal bigsur port interface qos-drop-history brief

To display the number of ingress packet drops for qos-drop history of type ‘brief’ of port type ethernet.

show hardware internal bigsur port interface qos-drop-history detail

To displays the number of Ingress packet Drops for qos-drop history of type ‘detail’, use the show hardware internal bigsur port interface qos-drop-history detail command in EXEC mode.

show hardware internal bigsur port ethernet [slot | port] qos-drop-history detail {all | multicast | unicast}

Syntax Description

ethernet

Specifies the interface type as ethernet with slot and port number as 1

slot

Specifies the slot number on the selected interface.

port

Specifies the port number on the selected interface.

all

Specifies the qos-drop-history brief of type all.

unicast

Specifies the qos-drop-history brief of type unicast

multicast

Specifies the qos-drop-history brief of type multicast

Command Default

None

Command Modes

EXEC mode

Command History

Release

Modification

7.2(0)N1(1)

This command was introduced.

Examples

This example shows the number of Ingress all packet drops with timestamp for QoS-drop-history detail for the selected ethernet interface:

switch# show hardware internal bigsur port ethernet 1/1 qos-drop-history detail all

QoS all drops history

+-------------------+----------+

| Timestamp | Drops |

+-------------------+----------+

|2015:06:02 09:12:17| 0|

+-------------------+----------+

|2015:06:02 09:12:12| 0|

+-------------------+----------+

|2015:06:02 09:12:07| 0|

+-------------------+----------+

|2015:06:02 09:12:02| 0|

+-------------------+----------+

|2015:06:02 09:11:56| 0|

+-------------------+----------+

|2015:06:02 09:11:51| 0|

+-------------------+----------+

|2015:06:02 09:11:46| 0|

+-------------------+----------+

|2015:06:02 09:11:41| 0|

+-------------------+----------+

|2015:06:02 09:11:36| 0|

+-------------------+----------+

This example shows the number of Ingress multicast packet drops with timestamp for QoS-drop-history detail for the selected ethernet interface:

switch# show hardware internal bigsur port ethernet 1/1 qos-drop-history detail multicast

QoS multicast drop history

+-------------------+----------+

| Timestamp | Drops |

+-------------------+----------+

|2015:06:02 09:16:14| 0|

+-------------------+----------+

|2015:06:02 09:16:09| 0|

+-------------------+----------+

|2015:06:02 09:16:03| 0|

+-------------------+----------+

|2015:06:02 09:15:58| 0|

+-------------------+----------+

|2015:06:02 09:15:53| 0|

+-------------------+----------+

|2015:06:02 09:15:48| 0|

+-------------------+----------+

|2015:06:02 09:15:43| 0|

+-------------------+----------+

|2015:06:02 09:15:38| 0|

+-------------------+----------+

|2015:06:02 09:15:33| 0|

+-------------------+----------+

|2015:06:02 09:15:27| 0|

+-------------------+----------+

|2015:06:02 09:15:22| 0|

This example shows the number of Ingress unicast packet drops with timestamp for QoS-drop-history detail for the selected ethernet interface:

switch# show hardware internal bigsur port ethernet 1/1 qos-drop-history detail unicast

QoS unicast drop history

+-------------------+----------+

| Timestamp | Drops |

+-------------------+----------+

|2015:06:02 09:13:03| 0|

+-------------------+----------+

|2015:06:02 09:12:58| 0|

+-------------------+----------+

|2015:06:02 09:12:53| 0|

+-------------------+----------+

|2015:06:02 09:12:48| 0|

+-------------------+----------+

|2015:06:02 09:12:43| 0|

+-------------------+----------+

|2015:06:02 09:12:37| 0|

+-------------------+----------+

|2015:06:02 09:12:32| 0|

+-------------------+----------+

|2015:06:02 09:12:27| 0|

+-------------------+----------+

|2015:06:02 09:12:22| 0|

+-------------------+----------+

|2015:06:02 09:12:17| 0|

+-------------------+----------+

|2015:06:02 09:12:12| 0|

+-------------------+----------+

|2015:06:02 09:12:07| 0|

+-------------------+----------+

|2015:06:02 09:12:02| 0|

+-------------------+----------+

|2015:06:02 09:11:56| 0|

+-------------------+----------+

|2015:06:02 09:11:51| 0|

+-------------------+----------+

|2015:06:02 09:11:46| 0|

Related Commands

Command

Description

show hardware internal bigsur port interface qos-drop-history detail

To display the number of ingress packet drops for qos-drop history of type ‘brief’ of port type ethernet.

show hardware internal bigsur port interface qos-drop-history brief

To displays the number of Ingress packet Drops for qos-drop history of type ‘brief’, use the show hardware internal bigsur port interface qos-drop-history brief command in EXEC mode.

show hardware internal bigsur port ethernet [slot | port] qos-drop-history brief {all | multicast | unicast}

Syntax Description

ethernet

Specifies the interface type as ethernet with slot and port number as 1

slot

Specifies the slot number on the selected interface.

port

Specifies the port number on the selected interface.

all

Specifies the qos-drop-history brief of type all.

unicast

Specifies the qos-drop-history brief of type unicast

multicast

Specifies the qos-drop-history brief of type multicast

Command Default

None

Command Modes

EXEC mode

Command History

Release

Modification

7.2(0)N1(1)

This command was introduced.

Examples

This example shows the number of Ingress all packet drops with timestamp for QoS-drop-history brief for the selected ethernet interface:

switch# show hardware internal bigsur port ethernet 1/1 qos-drop-history brief all

QoS all drops history

+-------------+------------+------------+------------+------------+------------+

| port | 5sec | 10sec | 60sec | 5min | 1hr |

+-------------+------------+------------+------------+------------+------------+

Ethernet1/1| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

This example shows the number of Ingress multicast packet drops with timestamp for QoS-drop-history detail for the selected ethernet interface:

switch# show hardware internal bigsur port ethernet 1/1 qos-drop-history brief unicast

QoS unicast drop history

+-------------+------------+------------+------------+------------+------------+

| port | 5sec | 10sec | 60sec | 5min | 1hr |

+-------------+------------+------------+------------+------------+------------+

Ethernet1/1| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

This example shows the number of Ingress unicast packet drops with timestamp for QoS-drop-history detail for the selected ethernet interface:

switch# show hardware internal bigsur port ethernet 1/1 qos-drop-history brief multicast

QoS multicast drop history

+-------------+------------+------------+------------+------------+------------+

| port | 5sec | 10sec | 60sec | 5min | 1hr |

+-------------+------------+------------+------------+------------+------------+

Ethernet1/1| 0| 0| 0| 0| 0|

--------------+------------+------------+------------+------------+------------

Related Commands

Command

Description

show hardware internal bigsur port interface qos-drop-history detail

To display the number of ingress packet drops for qos-drop history of type ‘detail’ of port type ethernet.

show interface burst-counters

To display the micro-burst counter information for a specified interface or all interfaces, use the show interface burst-counters command.

show interface [ethernet slot/port]] burst-counters

Syntax Description

ethernet slot/port

(Optional) Specifies a single Ethernet interface and its slot number and port number. The slot number is from 1 to 255. The port number is from 1 to 128.

Command Default

None

Command Modes

Any command mode

Command History

Release

Modification

7.0(0)N1(1)

This command was introduced.

Usage Guidelines

When the burst threshold command is used to enable micro-burst detection on a port, any activity that occurs on the port and that meets the specified criteria, is identified as a micro-burst and the appropriate burst counters are incremented. To display the burst counter information, you use the show burst-counters command.

If you do not specify an interface, the show interface burst-counters command will display the micro-burst counter information for all interfaces.

Examples

This example shows how to display the micro-burst counter details for a specified interface:

switch# show interface ethernet 1/1 burst-counters

--------------------------------------------------------------------

| Interface | Ingress Bursts | Egress Bursts | Total Bursts |

--------------------------------------------------------------------

| Ethernet1/1| 0| 0| 0|

switch#

This example shows how to display the micro-burst counter details for all interfaces where micro-burst monitoring is configured. In this example, micro-burst counters are configured on the Ethernet 1/1 and Ethernet 1/5 interfaces:

switch# show interface burst-counters

switch# show interface burst-counters

--------------------------------------------------------------------

| Interface | Ingress Bursts | Egress Bursts | Total Bursts |

--------------------------------------------------------------------

| Ethernet1/1| N/A| 50| 50|

| Ethernet1/5| 50| N/A| 50|

Related Commands

Command

Description

burst maximum

Configures the maximum number of bursts allowed within a time interval before generating an interrupt.

burst threshold

Configures micro-burst threshold values for an interface.

clear burst-counters

Clears burst counter values.

show interface priority-flow-control

To display the priority flow control details for a specified interface, use the show interface priority-flow-control command.

show interface [ethernet slot/[QSFP-module/]port]] priority-flow-control

Syntax Description

ethernet slot/QSFP-module/port]

(Optional) Specifies the Ethernet interface and its slot number and port number. The slot number is from 1 to 255. The QSFP-module number is from 1 to 199. The port number is from 1 to 128.

Command Default

None

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can use this command to display the priority flow control information for the following interfaces:

- Layer 2 interface

- Layer 3 interface

Note Use the no switchport command to configure an interface as a Layer 3 interface, and then use the flowcontrol command to configure flow control for the interface.

If you do not specify an interface, the show interface priority-flow-control command will display the priority flow control information for all interfaces (Layer 2, Layer 3).

Examples

This example shows how to display the priority flow control details for a specified interface:

switch# show interface ethernet 1/2 priority-flow-control

============================================================

Port Mode Oper(VL bmap) RxPPP TxPPP

============================================================

Ethernet1/2 Auto On (9) 4088353 1890

switch#

The interface specified is Ethernet 1/2, the PFC mode is set to negotiate PFC capability, the operation is on, and packets transmitted is 1890.

This example shows how to display the priority flow control information for a specified Layer 3 interface:

switch# show interface ethernet 1/5 priority-flow-control

============================================================

Port Mode Oper(VL bmap) RxPPP TxPPP

============================================================

Ethernet1/5 On On (0) 0 0

switch#

This example shows how to display the priority flow control information for all interfaces:

switch# show interface priority-flow-control

============================================================

Port Mode Oper(VL bmap) RxPPP TxPPP

============================================================

Ethernet1/1 Auto Off 0 0

Ethernet1/2 Auto Off 0 0

Ethernet1/3 Auto Off 0 0

Ethernet1/4 Auto Off 0 0

Ethernet1/5 On On (0) 0 0

Ethernet1/6 Auto Off 0 0

Ethernet1/7 Auto Off 0 0

Ethernet1/8 Auto Off 0 0

Ethernet1/9 Auto Off 0 0

Ethernet1/10 Auto Off 0 0

Ethernet1/11 Auto Off 0 0

Ethernet1/12 Auto Off 0 0

Ethernet1/13 Auto Off 0 0

Ethernet1/14 Auto Off 0 0

Ethernet1/15 Auto Off 0 0

Ethernet1/16 Auto Off 0 0

Ethernet1/17 Auto Off 0 0

Ethernet1/18 Auto Off 0 0

Ethernet1/19 Auto Off 0 0

Ethernet1/20 Auto Off 0 0

Ethernet1/21 Auto Off 0 0

Ethernet1/22 Auto Off 0 0

Ethernet1/23 Auto Off 0 0

Ethernet1/24 Auto Off 0 0

Ethernet1/25 Auto Off 0 0

Ethernet1/26 Auto Off 0 0

Ethernet1/27 Auto Off 0 0

Ethernet1/28 Auto Off 0 0

Ethernet1/29 Auto Off 0 0

Ethernet1/30 Auto Off 0 0

Ethernet1/31 Auto Off 0 0

Ethernet1/32 Auto Off 0 0

Ethernet3/1 Auto Off 0 0

Ethernet3/2 Auto Off 0 0

Ethernet3/3 Auto Off 0 0

Ethernet3/4 Auto Off 0 0

Ethernet3/5 Auto Off 0 0

Ethernet3/6 Auto Off 0 0

Ethernet3/7 Auto Off 0 0

Ethernet3/8 Auto Off 0 0

Ethernet3/9 Auto Off 0 0

Ethernet3/10 Auto Off 0 0

Ethernet3/11 Auto Off 0 0

Ethernet3/12 Auto Off 0 0

Ethernet3/13 Auto Off 0 0

Ethernet3/14 Auto Off 0 0

Ethernet3/15 Auto Off 0 0

Ethernet3/16 Auto Off 0 0

Ethernet3/17 Auto Off 0 0

Ethernet3/18 Auto Off 0 0

Ethernet3/19 Auto Off 0 0

Ethernet3/20 Auto Off 0 0

Ethernet3/21 Auto Off 0 0

Ethernet3/22 Auto Off 0 0

Ethernet3/23 Auto Off 0 0

Ethernet3/24 Auto Off 0 0

Ethernet3/25 Auto Off 0 0

Ethernet3/26 Auto Off 0 0

Ethernet3/27 Auto Off 0 0

Ethernet3/28 Auto Off 0 0

Ethernet3/29 Auto Off 0 0

Ethernet3/30 Auto Off 0 0

Ethernet3/31 Auto Off 0 0

Ethernet3/32 Auto Off 0 0

Ethernet100/1/1 Auto Off 0 0

Ethernet100/1/2 Auto Off 0 0

Ethernet100/1/3 Auto Off 0 0

Ethernet100/1/4 Auto Off 0 0

Ethernet100/1/5 Auto Off 0 0

Ethernet100/1/6 Auto Off 0 0

Ethernet100/1/7 Auto Off 0 0

Ethernet100/1/8 Auto Off 0 0

Ethernet100/1/9 Auto Off 0 0

Ethernet100/1/10 Auto Off 0 0

Ethernet100/1/11 Auto Off 0 0

Ethernet100/1/12 Auto Off 0 0

Ethernet100/1/13 Auto Off 0 0

Ethernet100/1/14 Auto Off 0 0

Ethernet100/1/15 Auto Off 0 0

Ethernet100/1/16 Auto Off 0 0

switch#

Related Commands

Command

Description

no switchport

Configures a Layer 3 routed interface.

priority-flow-control

Sets the PFC mode for the selected interface.

show interface untagged-cos

To display the untagged class of service (CoS) values for a specified interface, use the show interface untagged-cos command.

show interface untagged-cos [module module_no]

Syntax Description

module

(Optional) Displays the interfaces on this module of the switch chassis.

module_no

Module number in the switch chassis. The range is from 1 to 18.

Command Default

None

Command Modes

EXEC mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the untagged CoS values for interfaces:

switch# show interface untagged-cos

=================================

Interface Untagged-CoS

=================================

port-channel1

port-channel3 2

port-channel5 5

port-channel6

port-channel12

port-channel15

port-channel20

port-channel24

port-channel25

port-channel33

port-channel41

port-channel44

--More--

switch#

This example shows how to display the untagged CoS values for all interfaces (Layer 2, Layer 3):

switch# show interface untagged-cos

S3(config-if)# show int untagged-cos

=================================

Interface Untagged-CoS

=================================

port-channel100

port-channel127

port-channel128

Ethernet1/1

Ethernet1/2

Ethernet1/3

Ethernet1/4

Ethernet1/5 3

Ethernet1/6

Ethernet1/7

Ethernet1/8

Ethernet1/9

Ethernet1/10

Ethernet1/11

Ethernet1/12

:

<--snip-->

Ethernet3/31

Ethernet3/32

Ethernet100/1/1

Ethernet100/1/2

<--Output truncated-->

switch#

Related Commands

Command

Description

untagged cos

Sets a CoS value for untagged Ethernet frames.

show policy-map

To display policy maps, use the show policy-map command.

show policy-map [type {network-qos | qos | queuing}] [policy-map-name]

Syntax Description

type

(Optional) Specifies the component type to display.

network-qos

Displays policy maps of type network-qos.

qos

Displays policy maps of type qos only.

queuing

Displays policy maps of type queuing only.

policy-map-name

(Optional) Named policy map. The name can be a maximum of 40 alphanumeric characters.

Command Default

None

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

When you enter the show policy-map command with no arguments or keywords, the system also displays the Control Plane Policing (CoPP) information.

Examples

This example shows how to display a named network-qos policy map:

switch# show policy-map type network-qos my_pnq

Type network-qos policy-maps

===============================

policy-map type network-qos my_pnq

class type network-qos cl_nq

multicast-optimize

queue-limit 20480 bytes

mtu 1500

class type network-qos class-fcoe

pause no-drop

mtu 2158

class type network-qos class-default

mtu 1500

switch#

Related Commands

Command

Description

policy-map

Creates or modifies a policy map.

show policy-map interface

To display the service policy maps configured on the interfaces, use the show policy-map interface command.

show policy-map interface [ethernet slot/[QSFP-module/]port | port-channel channel-number] [input | output] [type {qos | queuing}]

Syntax Description

ethernet

(Optional) Displays policy maps assigned to Ethernet interfaces.

slot/[QSFP-module/]port

Ethernet interface slot number and port number. The slot number is from 1 to 255. The QSFP-module number is from 1 to 199. The port number is from 1 to 128.

port-channel

(Optional) Displays policy maps assigned to EtherChannels.

channel-number

EtherChannel number. The number is from 1 to 4096.

input

(Optional) Displays policy maps assigned to input traffic only.

output

(Optional) Displays policy maps assigned to output traffic only.

type

(Optional) Specifies the component type to display.

qos

Displays policy maps of type qos only.

queuing

Displays policy maps of type queuing only.

Command Default

None

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Statistics are on by default.

Examples

This example shows how to display policy maps assigned to a specified interface:

switch(config)# show policy-map interface ethernet 2/10

This example shows how to display QoS policy maps assigned to a specified interface:

switch# show policy-map interface ethernet 3/1 type qos

Global statistics status : disabled

Ethernet3/1

Service-policy (qos) input: s

policy statistics status: disabled

Class-map (qos): s1 (match-any)

Match: cos 0

set qos-group 2

Class-map (qos): class-1-2 (match-any)

Match: cos 1-2

set qos-group 3

Class-map (qos): class-4-5 (match-any)

Match: cos 4-5

set qos-group 4

Class-map (qos): class-6 (match-any)

Match: cos 6

set qos-group 5

Class-map (qos): class-fcoe (match-any)

Match: cos 3

set qos-group 1

Class-map (qos): class-default (match-any)

Match: any

set qos-group 0

switch#

This example shows how to display the policy maps assigned to the output traffic of a specified interface:

switch# show policy-map interface ethernet 3/1 output

Global statistics status : disabled

Ethernet3/1

Service-policy (queuing) output: pqe1

policy statistics status: disabled

Class-map (queuing): cqe1 (match-any)

Match: qos-group 2

bandwidth percent 20

Class-map (queuing): cqe2 (match-any)

Match: qos-group 3

priority

Class-map (queuing): cqe3 (match-any)

Match: qos-group 4

bandwidth percent 20

Class-map (queuing): cqe4 (match-any)

Match: qos-group 5

bandwidth percent 40

Class-map (queuing): class-fcoe (match-any)

Match: qos-group 1

bandwidth percent 10

Class-map (queuing): class-default (match-any)

Match: qos-group 0

bandwidth percent 5

switch#

This example shows how to display the policy maps assigned to the input traffic of a virtual Ethernet interface:

switch# show policy-map interface vethernet 10 input type queuing

Global statistics status : disabled

Vethernet10

Service-policy (queuing) input: p2

policy statistics status: disabled

Class-map (queuing): class-default (match-any)

Match: qos-group 0

bandwidth percent 50

shape 30 kbps

switch#

Related Commands

Command

Description

policy-map

Creates or modifies a policy map.

service-policy (virtual Ethernet interface)

Attaches a policy map to a virtual Ethernet interface.

show policy-map interface brief

To display policy maps applied to interfaces in a brief format, use the show policy-map interface brief command.

show policy-map interface brief

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display assigned policy maps in a brief format:

switch(config)# show policy-map interface brief

Interface [Status]:INP QOS INP QUE OUT QUE

===================================================================

port-channel1 [Active]:p1 pqe1 pqe1

port-channel3 [Active]:s pqe1 pqe1

port-channel5 [Active]:s pqe1 pqe1

port-channel6 [Active]:s pqe1 pqe1

port-channel12 [Active]:p12 p12-in p12-out

port-channel15 [Active]:s pqe1 pqe1

port-channel20 [Active]:s pqe1 pqe1

port-channel24 [Active]:p4 pqe1 pqe1

port-channel25 [Active]:p4 pqe1 pqe1

port-channel33 [Active]:s pqe1 pqe1

port-channel41 [Active]:s pqe1 pqe1

port-channel44 [Active]:s pqe1 pqe1

port-channel48 [Active]:s pqe1 pqe1

port-channel101 [Active]:s pqe1 pqe1

port-channel102 [Active]:p4

port-channel103 [Active]:p4

port-channel104 [Active]:p4

port-channel105 [Active]:p4

port-channel106 [Active]:p4

port-channel107 [Active]:p4

--More--

switch(config)#

This example shows how to display assigned policy maps in a brief format on a switch that runs Cisco NX-OS Release 5.0(3)N1(1):

switch# show policy-map interface brief

S3(config-if)# show policy-map interface brief

Interface/VLAN [Status]:INP QOS OUT QOS INP QUE OUT QUE

================================================================================

port-channel100 [Active]:default-in-po default-in-po default-out-p

port-channel127 [Active]:default-in-po default-in-po default-out-p

port-channel128 [Active]:default-in-po default-in-po default-out-p

Ethernet1/1 [Active]:default-in-po default-in-po default-out-p

Ethernet1/2 [Active]:default-in-po default-in-po default-out-p

Ethernet1/3 [Active]:default-in-po default-in-po default-out-p

Ethernet1/4 [Active]:default-in-po default-in-po default-out-p

Ethernet1/5 [Active]:default-in-po default-in-po default-out-p

Ethernet1/6 [Active]:default-in-po default-in-po default-out-p

:

<Snip>

:

Ethernet3/31 [Active]:default-in-po default-in-po default-out-p

Ethernet3/32 [Active]:default-in-po default-in-po default-out-p

Ethernet100/1/1 [Active]:default-in-po default-in-po default-out-p

Ethernet100/1/2 [Active]:default-in-po default-in-po default-out-p

Ethernet100/1/3 [Active]:default-in-po default-in-po default-out-p

<--Output truncated-->

switch#

Related Commands

Command

Description

policy-map

Creates or modifies a policy map.

show policy-map

Displays policy maps.

show policy-map interface control-plane

To display the control-plane policy maps applied to interfaces, use the show policy-map interface control-plane command.

show policy-map interface control-plane

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display assigned control-plane policy maps:

switch# show policy-map interface control-plane

control Plane

service-policy input: copp-system-policy-default

class-map copp-system-class-igmp (match-any)

match protocol igmp

police cir 1024 kbps , bc 65535 bytes

conformed 0 bytes; action: transmit

violated 0 bytes; action: drop

class-map copp-system-class-pim-hello (match-any)

match protocol pim

police cir 1024 kbps , bc 4800000 bytes

conformed 0 bytes; action: transmit

violated 0 bytes; action: drop

class-map copp-system-class-bridging (match-any)

match protocol bridging

police cir 20000 kbps , bc 4800000 bytes

conformed 0 bytes; action: transmit

violated 0 bytes; action: drop

class-map copp-system-class-arp (match-any)

match protocol arp

<--Output truncated-->

switch(config)#

Related Commands

Command

Description

policy-map

Creates or modifies a policy map.

show policy-map

Displays policy maps.

show policy-map system

To display all active policy maps in the system, use the show policy-map system command.

show policy-map system [type {network-qos | qos [input] | queuing [input | output]}]

Syntax Description

type

(Optional) Specifies the component type to display.

network-qos

Displays policy maps of type network-qos only.

qos

Displays policy maps of type qos only.

input

(Optional) Displays policy maps assigned to input traffic.

queuing

Displays policy maps of type queuing only.

output

(Optional) Displays policy maps assigned to output traffic.

Command Default

All policy maps

Command Modes

EXEC mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

If you do not specify a policy map type and name, the system displays all the active policy maps in the system.

Examples

This example shows how to display all active policy maps in the system:

switch# show policy-map system

Type network-qos policy-maps

===============================

policy-map type network-qos s

class type network-qos s2 match qos-group 3

mtu 4000

class type network-qos s1 match qos-group 2

mtu 5000

set cos 0

multicast-optimize

pause no-drop

class type network-qos s3 match qos-group 4

mtu 9216

class type network-qos s4 match qos-group 5

mtu 9216

class type network-qos class-fcoe match qos-group 1

pause no-drop

mtu 2158

class type network-qos class-default match qos-group 0

mtu 1500

Service-policy (qos) input: s

policy statistics status: disabled

Class-map (qos): s1 (match-any)

Match: cos 0

set qos-group 2

Class-map (qos): class-1-2 (match-any)

Match: cos 1-2

set qos-group 3

Class-map (qos): class-4-5 (match-any)

Match: cos 4-5

set qos-group 4

Class-map (qos): class-6 (match-any)

Match: cos 6

set qos-group 5

Class-map (qos): class-fcoe (match-any)

Match: cos 3

set qos-group 1

Class-map (qos): class-default (match-any)

Match: any

set qos-group 0

Service-policy (queuing) input: pqe1

policy statistics status: disabled

Class-map (queuing): cqe1 (match-any)

Match: qos-group 2

bandwidth percent 20

Class-map (queuing): cqe2 (match-any)

Match: qos-group 3

priority

Class-map (queuing): cqe3 (match-any)

Match: qos-group 4

bandwidth percent 20

Class-map (queuing): cqe4 (match-any)

Match: qos-group 5

bandwidth percent 40

Class-map (queuing): class-fcoe (match-any)

Match: qos-group 1

bandwidth percent 10

Class-map (queuing): class-default (match-any)

Match: qos-group 0

bandwidth percent 5

Service-policy (queuing) output: pqe1

policy statistics status: disabled

Class-map (queuing): cqe1 (match-any)

Match: qos-group 2

bandwidth percent 20

Class-map (queuing): cqe2 (match-any)

Match: qos-group 3

priority

Class-map (queuing): cqe3 (match-any)

Match: qos-group 4

bandwidth percent 20

Class-map (queuing): cqe4 (match-any)

Match: qos-group 5

bandwidth percent 40

Class-map (queuing): class-fcoe (match-any)

Match: qos-group 1

bandwidth percent 10

Class-map (queuing): class-default (match-any)

Match: qos-group 0

bandwidth percent 5

switch#

This example shows how to display active network-qos policy maps in the system:

switch# show policy-map system type network-qos

Type network-qos policy-maps

===============================

policy-map type network-qos s

class type network-qos s2 match qos-group 3

mtu 4000

class type network-qos s1 match qos-group 2

mtu 5000

set cos 0

multicast-optimize

pause no-drop

class type network-qos s3 match qos-group 4

mtu 9216

class type network-qos s4 match qos-group 5

mtu 9216

class type network-qos class-fcoe match qos-group 1

pause no-drop

mtu 2158

class type network-qos class-default match qos-group 0

mtu 1500

switch#

Related Commands

Command

Description

show policy-map

Displays all policy maps.

show policy-map type control-plane

To display control plane policy map information, use the show policy-map type control-plane command.

show policy-map type control-plane [expand] [name policy-map-name]

Syntax Description

expand

(Optional) Displays expanded control plane policy map information.

name policy-map-name

(Optional) Specifies the name of the control plane policy map. The name is case sensitive and can be a maximum of 64 alphanumeric characters.

Command Default

None

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display control plane policy map information:

switch# show policy-map type control-plane

policy-map type control-plane copp-system-policy-customized

class copp-system-class-igmp

police cir 1024 kbps bc 65535 bytes

class copp-system-class-pim-hello

police cir 1024 kbps bc 4800000 bytes

class copp-system-class-bridging

police cir 20000 kbps bc 4800000 bytes

class copp-system-class-arp

police cir 1024 kbps bc 3600000 bytes

class copp-system-class-dhcp

police cir 1024 kbps bc 4800000 bytes

class copp-system-class-mgmt

police cir 12000 kbps bc 4800000 bytes

class copp-system-class-lacp

police cir 1024 kbps bc 4800000 bytes

class copp-system-class-lldp

police cir 2048 kbps bc 4800000 bytes

class copp-system-class-udld

police cir 2048 kbps bc 4800000 bytes

<--Output truncated-->

switch#

This example shows how to display control plane policy map information in expanded format:

switch# show policy-map type control-plane expand

Related Commands

Command

Description

policy-map type control-plane

Creates or configures a control plane policy map.

show policy-map vlan

To display VLAN policy maps, use the show policy-map vlan command.

show policy-map vlan [vlan-number]

Syntax Description

vlan-number

Displays the QoS policies configured on the specified VLAN.

Command Default

None

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You must configure the interface QoS limit and policy map before using the show policy-map vlan command. The TCAM must have enough free entries to configure the service policy on the VLAN.

Examples

This example shows how to display the QoS policies configured on the specified VLAN:

switch# show policy-map vlan 101

Service-policy (qos) input: vpq1

===============================

policy status statistics: disabled

class-map (qos): vcq2 (match-any)

match: cos 2

match: precedence 1

set cos-group 2

set prec 2

class-map (qos): vcq4 (match-any)

match: access-group ipacl1-vq

match: prec 7

set cos-group 4

class-map (qos): vcq4 (match-any)

match: cos 1

set cos-group 3

class-map (qos): vcq4 (match-any)

match: any

set cos-group 0

switch#

Related Commands

Command

Description

policy-map

Creates or modifies a policy map.

show queuing interface

To display the queuing information on interfaces, use the show queuing interface command.

show queuing interface [ethernet slot/[QSFP-module/]port]

Syntax Description

ethernet

(Optional) Specifies that queuing information to be displayed for an Ethernet interface.

slot/[QSFP-module/]port]

(Optional) The slot number is from 1 to 255. The QSFP-module number is from 1 to 199. The port number is from 1 to 128.

Command Default

Displays the queuing information for all interfaces.

Command Modes

EXEC mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the queuing information for all interfaces:

switch# show queuing interface

Ethernet1/1 queuing information:

TX Queuing

qos-group sched-type oper-bandwidth

0 WRR 100

1 WRR 0

2 WRR 0

3 WRR 0

RX Queuing

qos-group 0

q-size: 100160, HW MTU: 1500 (1500 configured)

drop-type: drop, xon: 0, xoff: 0

Statistics:

Pkts received over the port : 0

Ucast pkts sent to the cross-bar : 0

Mcast pkts sent to the cross-bar : 0

Ucast pkts received from the cross-bar : 0

Pkts sent to the port : 150

Pkts discarded on ingress : 0

Per-priority-pause status : Rx (Inactive), Tx (Inactive)

qos-group 1

q-size: 100160, HW MTU: 1500 (1500 configured)

drop-type: drop, xon: 0, xoff: 0

Statistics:

Pkts received over the port : 0

Ucast pkts sent to the cross-bar : 0

Mcast pkts sent to the cross-bar : 0

Ucast pkts received from the cross-bar : 0

Pkts sent to the port : 0

Pkts discarded on ingress : 0

Per-priority-pause status : Rx (Inactive), Tx (Inactive)

qos-group 2

q-size: 100160, HW MTU: 1500 (1500 configured)

drop-type: drop, xon: 0, xoff: 0

Statistics:

Pkts received over the port : 0

Ucast pkts sent to the cross-bar : 0

Mcast pkts sent to the cross-bar : 0

Ucast pkts received from the cross-bar : 0

Pkts sent to the port : 0

Pkts discarded on ingress : 0

Per-priority-pause status : Rx (Inactive), Tx (Inactive)

qos-group 3

q-size: 100160, HW MTU: 1500 (1500 configured)

drop-type: drop, xon: 0, xoff: 0

Statistics:

Pkts received over the port : 0

Ucast pkts sent to the cross-bar : 0

Mcast pkts sent to the cross-bar : 0

Ucast pkts received from the cross-bar : 0

Pkts sent to the port : 0

Pkts discarded on ingress : 0

Per-priority-pause status : Rx (Inactive), Tx (Inactive)

switch#

This example shows how to display the queuing information on Ethernet interface 1/2:

switch# show queuing interface ethernet 1/2

Ethernet1/2 queuing information:

TX Queuing

qos-group sched-type oper-bandwidth

0 WRR 73

1 WRR 0

2 WRR 1

3 WRR 6

4 WRR 20

5 priority 0

RX Queuing

qos-group 0

q-size: 25600, HW MTU: 9280 (9216 configured)

drop-type: drop, xon: 0, xoff: 160

Statistics:

Pkts received over the port : 0

Ucast pkts sent to the cross-bar : 0

Mcast pkts sent to the cross-bar : 0

Ucast pkts received from the cross-bar : 1851526994

Pkts sent to the port : 1851527000

Pkts discarded on ingress : 0

Per-priority-pause status : Rx (Inactive), Tx (Inactive)

qos-group 1

q-size: 76800, HW MTU: 2240 (2158 configured)

drop-type: no-drop, xon: 128, xoff: 240

Statistics:

Pkts received over the port : 0

Ucast pkts sent to the cross-bar : 0

Mcast pkts sent to the cross-bar : 0

Ucast pkts received from the cross-bar : 0

Pkts sent to the port : 0

Pkts discarded on ingress : 0

Per-priority-pause status : Rx (Inactive), Tx (Inactive)

qos-group 2

q-size: 20480, HW MTU: 9280 (9216 configured)

drop-type: drop, xon: 0, xoff: 128

Statistics:

Pkts received over the port : 0

Ucast pkts sent to the cross-bar : 0

Mcast pkts sent to the cross-bar : 0

Ucast pkts received from the cross-bar : 0

Pkts sent to the port : 0

Pkts discarded on ingress : 0

Per-priority-pause status : Rx (Inactive), Tx (Inactive)

--More--

switch#

Table 1 describes the significant fields shown in the display.

Table 1 show queuing interface Field Descriptions

Field

Description

Ethernet ...

Ethernet interface information.

qoS-group

Information about QoS groups configured on the switch.

sched-type

Type of schedule.

WRR

Weighted round robin(WRR). Queue eight for scheduling.

Priority

Priority of the queue.

q-size

Queue size.

drop-type

Queue drop type can be either drop or no-drop.

MTU

Maximum transmit unit (MTU) for the queue.

Xon

Transmission on at this threshold.

Xoff

Transmission off at this threshold.

Related Commands

Command

Description

hardware buffer-threshold

Configures the hardware buffer threshold.

hardware queue-limit

Configures the hardware queue limit.

show fex

Displays all configured Fabric Extender chassis connected to the switch.

show running-config copp

To display Control Plane Policing (CoPP) configuration information in the running configuration, use the show running-config copp command.

show running-config copp [all]

Syntax Description

all

(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the configured CoPP information in the running configuration on a switch that runs Cisco NX-OS Release 5.1(3)N1(1):

switch# show running-config copp

This example shows how to display the configured and default CoPP information in the running configuration:

switch# show running-config copp all

Related Commands

Command

Description

control-plane

Enters the control-plane configuration mode.

copy running-config startup-config

Copies the running configuration to the startup configuration file.

show startup-config aclmgr

Displays the ACL startup configuration.

show startup-config copp

Displays the CoPP configuration information in the startup configuration file.

show running-config ipqos

To display information about the running-system configuration for quality of service (QoS), use the show running-config ipqos command.

show running-config ipqos [all]

Syntax Description

all

(Optional) Displays configured and default information.

Command Default

None

Command Modes

EXEC mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Use this command to view a list of default and configured class maps and policy maps and the policies attached to interfaces.

Examples

This example shows how to display QoS information on a switch that runs Cisco NX-OS Release 5.0(2)N1(1):

switch# show running-config ipqos

!Command: show running-config ipqos

!Time: Thu Sep 9 06:26:49 2010

version 5.0(2)N1(1)

class-map type qos class-fcoe

match cos 4

class-map type qos match-all 1

match cos 1

class-map type qos match-all 2

match cos 2

class-map type qos match-all 3

match cos 3

class-map type qos match-all 4

class-map type qos match-any 5

match cos 5,7

class-map type qos match-all arp

match protocol dhcp

match protocol arp

match cos 3

class-map type qos match-all cos

match cos 5

class-map type qos match-all dot

match access-group name dot

class-map type qos match-all my_class

match dscp 3

match precedence 0

match protocol dhcp

class-map type qos match-all new

match protocol netbios

:

<snip>

class-map type queuing my_qclass

match qos-group 3

class-map type queuing Video-Signalling

match qos-group 4

class-map type queuing class-ip-multicast

match qos-group 4

policy-map type qos 5

class 5

set qos-group 2

class Video

set qos-group 3

policy-map type qos my_policy

class my_class

set precedence 5

set dscp 5

class myQAll

set precedence 3

set dscp 48

:

<snip>

policy-map type network-qos my_policy1

class type network-qos my_class1

pause no-drop buffer-size 143680 pause-threshold 58860 resume-threshold 3840

class type network-qos class-fcoe

pause no-drop

mtu 2158

class type network-qos class-default

:

<snip>

system qos

service-policy type qos input voice

service-policy type network-qos Network

service-policy type queuing output Queu

service-policy type queuing input Queue

<--output truncated-->

switch#

This example shows how to display QoS information on a switch that runs Cisco NX-OS Release 5.0(3)N1(1):

switch# show running-config ipqos

!Command: show running-config ipqos

!Time: Sun Apr 20 07:22:36 2008

version 5.0(3)N1(1)

class-map type qos class-fcoe

class-map type qos match-all c1

match cos 3-5

class-map type queuing class-fcoe

match qos-group 1

class-map type queuing class-all-flood

match qos-group 2

class-map type queuing class-ip-multicast

match qos-group 2

policy-map type qos p1

class c1

set qos-group 3

class-map type network-qos n1

match qos-group 1

class-map type network-qos class-fcoe

match qos-group 1

class-map type network-qos class-all-flood

match qos-group 2

class-map type network-qos class-ip-multicast

match qos-group 2

policy-map type network-qos n2

class type network-qos n1

class type network-qos class-default

multicast-optimize

interface Ethernet1/5

priority-flow-control mode on

untagged cos 3

switch#

The above display shows the QoS information for Layer 3 interfaces (Ethernet 1/5 configured as a Layer 3 interface).

Related Commands

Command

Description

copy running-config startup-config

Copies the running configuration to the startup configuration file.

show class-map

Displays information about class maps.

show policy-map

Displays information about policy maps.

show startup-config copp

To display the Control Plane Policing (CoPP) configuration information in the startup configuration, use the show startup-config copp command.

show startup-config copp

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the CoPP information in the startup configuration:

switch# show startup-config copp

Related Commands

Command

Description

control-plane

Enters the control-plane configuration mode.

copy running-config startup-config

Copies the running configuration to the startup configuration file.

show running-config copp

Displays the CoPP configuration information in the running configuration.

show startup-config ipqos

To display quality of service (QoS) configuration information in the startup configuration, use the show startup-config ipqos command.

show startup-config ipqos [all]

Syntax Description

all

(Optional) Displays configured and default information.

Command Default

None

Command Modes

EXEC mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the QoS information in the startup configuration file:

switch# show startup-config ipqos

!Command: show startup-config ipqos

!Time: Thu Sep 9 07:42:33 2010

!Startup config saved at: Tue Sep 7 08:45:03 2010

version 5.0(2)N1(1)

class-map type qos class-fcoe

match cos 4

class-map type qos match-all 1

match cos 1

class-map type qos match-all 2

match cos 2

class-map type qos match-all 3

match cos 3

class-map type qos match-all 4

class-map type qos match-any 5

match cos 5,7

class-map type qos match-all arp

match protocol dhcp

match protocol arp

match cos 3

class-map type qos match-all cos

match cos 5

class-map type qos match-all dot

match access-group name dot

class-map type qos match-all new

match protocol netbios

class-map type qos match-all rtp

match ip rtp 2000-40000

class-map type qos match-all dscp

match dscp 46

match precedence 7

match protocol arp

class-map type qos match-all Video

match dscp 34

class-map type qos match-all Voice

match dscp 40,46

class-map type qos match-all class1

match ip rtp 2000

class-map type qos match-all class2

match cos 1

class-map type qos match-all class3

match protocol arp

class-map type qos match-all class4

match protocol dhcp

class-map type qos match-all class5

match protocol ldp

:

:

<--output truncated--

switch#

Related Commands

Command

Description

copy running-config startup-config

Copies the running configuration to the startup configuration file.

show class-map

Displays information about class maps.

show policy-map

Displays information about policy maps.

show wrr-queue cos-map

To display the mapped class of service (CoS) values to egress queues, use the show wrr-queue cos-map command.

show wrr-queue cos-map

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the CoS values that are mapped to the egress queue:

switch# show wrr-queue cos-map

MCAST Queue ID Cos Map

0 0 1

1 2

2 3 4 5

3 6 7

switch#

Related Commands

Command

Description

wrr-queue cos-map

Maps class of service (CoS) values to select one of the egress queues.

U Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with U.

untagged cos

To override the class of service (CoS) value for the selected interface, use the untagged cos command. To revert to the defaults, use the no form of this command.

untagged cos cos-value

no untagged cos cos-value

Syntax Description

cos-value

Class of service (CoS) value for untagged frames. Values can range from 1 to 7.

Command Default

None

Command Modes

Interface configuration mode

Subinterface configuration mode

Virtual Ethernet interface configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

You can use this command on the following interfaces:

- Layer 2 interface

- Layer 3 interface

Note Use the no switchport command to configure an interface as a Layer 3 interface.

- Virtual Ethernet interface

Note Use the feature-set virtualization command to enable the Cisco Adapter Fabric Extender (Adapter-FEX) on the switch. Use the interface vethernet command to configure a virtual Ethernet interface.

Ethernet frames received with no CoS value are given a CoS value of 0.

On a Cisco Nexus 5548 switch, you can configure a type qos policy map and untagged CoS on the same interface.

Examples

This example shows how to set the CoS value to 4 for untagged frames received on an interface:

switch# configure terminal

switch(config)# interface ethernet 1/2

switch(config-if)# untagged cos 4

This example shows how to set the CoS value to 3 for untagged frames received on a Layer 3 interface:

switch# configure terminal

switch(config)# interface ethernet 1/5

switch(config-if)# no switchport

switch(config-if)# untagged cos 3

switch(config-if)#

This example shows how to set the CoS value to 5 for untagged frames received on a virtual Ethernet interface:

switch# configure terminal

switch(config)# feature adapter-fex

Virtualization Plugin license checked out successfully

Virtualization Plugin extracted successfully

All Virtualization processes enabled successfully

switch(config)# interface vethernet 10

switch(config-if)# untagged cos 5

switch(config-if)#

Related Commands

Command

Description

feature-set virtualization

Enables the Cisco Virtual Machine features on the switch.

interface vethernet

Configures a virtual Ethernet interface.

match cos

Sets the CoS value to match for the selected class.

no switchport

Configures an interface as a Layer 3 routed interface.

show interface untagged-cos

Displays the untagged CoS values for interfaces.

W Commands

This chapter describes the Cisco NX-OS quality of service (QoS) commands that begin with W.

wrr-queue cos-map

To map assigned class of service (CoS) values to select one of the egress queues, use the wrr-queue cos-map command. To return the CoS map to the default setting, use the no form of this command.

wrr-queue cos-map queue-id cos1 ... cos8

no wrr-queue cos-map queue-id cos1 ... cos8

Syntax Description

queue-id

ID of the egress queue. The range is from 0 to 3.

cos1... cos8

CoS values that are mapped to select a queue. Enter up to eight CoS values. Separate each value with a space. The range is from 0 to 7.

Command Default

The defaults are as follows:

- Receive queue 0 and transmit queue 0: CoS 0 and 1.

- Receive queue 1 and transmit queue 1: CoS 2 and 3.

- Receive queue 2 and transmit queue 2: CoS 4 and 5.

- Receive queue 3 and transmit queue 3: CoS 6 and 7.

Command Modes

Global configuration mode

Command History

Release

Modification

6.0(2)N1(1)

This command was introduced.

Usage Guidelines

Note This command is applicable only to Layer 3 multicast traffic.

You can use this command to distribute traffic into different queues, where each queue is configured with different weighted round robin (WRR) parameters.

You can configure a maximum of four multicast queues for Layer 3 multicast traffic. We recommend that you configure at least one class of service (CoS) value for each multicast queue.

Examples

Cisco Nexus 6000 Series NX-OS QoS Command Reference

Cisco NX-OS Releases 7.x

First Published: January 27, 2014

Last Updated: June 30, 2014

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

Cisco Nexus 6000 Series NX-OS QoS Command Reference

© 2014 Cisco Systems, Inc. All rights reserved.