|
|
|
|
Configuring DSCP for Locally Originated Packets |
Added the ip dscp-lop command. |
6.2(12) |
I Commands |
Configuring IPv6 |
Added the no-autoconfig keyword to the ipv6 nd prefix command |
6.2(8) |
I Commands |
Configuring Advanced BGP |
Added the following commands:
- ip forward
- ipv6 nd mac-extract
- timers prefix-peer-wait
Added the unchanged keyword to the set ip nexthop command. Updated the usage guidelines for the address-family (BGP) command. |
6.2(8) |
A Commands B Commands I Commands S Commands |
BGP PIC for Unicast |
Added the ip adjacency notify command. Added the install backup keywords to the additional paths command. |
6.2(8) |
A Commands I Commands |
OSPFv2 |
Added the max-metric route lsa (OPSFv2) command. |
6.2(8) |
M Commands |
OSPFv3 |
Added the max-metric route lsa (OPSFv3) command. |
6.2(8) |
M Commands |
DN bit ignore |
Added the down-bit-ignore command. |
6.2(2) |
D Commands |
Advanced BGP |
Added the following commands:
- disable-peer-as-check
- inject-map
- redistribute static route-map allow
- route-map allow permit
- set ip address prefix-list
- unsuppress-map
|
6.2(2) |
D Commands I Commands S Commands R Commands T Commands |
BGP |
Added the as-format asdot command. |
6.2(2) |
A Commands |
Configuring Advanced OSPFv2 |
Added the discard-route command. |
|
D Commands |
Configuring Basic OSPFv2 |
Added the following commands:
- name-lookup
- passive-interface default
|
6.2(2) |
N Commands P Commands |
Configuring EIGRP |
Added the match source-protocol command. |
6.2(2) |
M Commands |
Configuring IPv6 |
Added the following commands:
- ipv6 nd cache limit
- ipv6 nd dad attempts
- ipv6 nd fast-path
|
6.2(2) |
I Commands |
Configuring Static Routing |
Added the show ip static-route track-table command. |
6.2(2) |
Show Commands |
IP ARP |
Added the ip arp cache limit command. |
6.2(2) |
I Commands |
Glean Optimization |
Added the ip arp fast-path command. |
6.2(2) |
I Commands |
HRSP |
Added the following commands:
- follow
- hsrp version 2
- hsrp ipv6
- hsrp mac-refresh
- name
- passive-interface default
- show hsrp mgo
|
6.2(2) |
F Commands H Commands N Commands P Commands Show Commands |
Configuring ISIS |
Added the following commands:
- default isis passive-interface
- isis passive-interface
- no isis passive-interface
|
6.2(2) |
D Commands I Commands N Commands |
Configuring Policy-Based Routing |
Added the following commands:
- ipv4 local policy route-map
- ipv6 local policy route-map
- show local policy
|
6.2(2) |
I Commands Show Commands |
OSPFv2 and OSPFv3 |
Added the name-lookup command. |
6.2(2) |
N Commands |
Unicast FIB |
Added the following commands:
- event fib resource tcam usage
- event fib route
- show event manager events action-log policy
- show event manager policy-state
|
6.2(2) |
E Commands Show Commands |
VRRPv3 |
Added the following commands:
- feature vrrpv3
- vrrpv3 address-family
- timers advertise
- vrrs leader
- show fhrp
- vfhrp delay
- vrrs pathway
- show vrrs client
- show vrrs pathway
- show vrrs server
- show vrrs tag
|
6.2(2) |
F Commands Show Commands T Commands V Commands |
BGP |
Added the set path-selection all advertise command. |
6.1(1) |
S Commands |
Added the capability additional-paths command. |
6.1(1) |
C Commands |
Added the additional-paths command. |
6.1(1) |
A Commands |
Added weight command. |
6.1(1) |
W Commands |
Changed the show bgp ipv4 unicast command output. |
6.1(1) |
Show Commands |
OSPF and OSPFv3 |
Added the set-distance command. |
6.1(1) |
S Commands |
IS-IS |
Added the IPv6 keyword to the syntax description of address-family (RIP) command. |
6.1(1) |
A Commands |
OSPF and OSPFv3 |
Added the inter-area and intra-area keywords to the syntax description of match route-type command. |
6.1(1) |
T Commands |
|
Added the metric direct 0 command. |
6.1(1) |
M Commands |
OSPF |
Added the table-map (OSPF) command. |
6.1(1) |
T Commands |
IS-IS |
Added the adjacency-check command. |
6.1(1) |
A Commands |
EIGRP Wide Metrics |
Added the metric version command. |
5.2(1) |
M Commands |
Added the metric rib-scale command. |
5.2(1) |
M Commands |
Layer 3 VPN Support |
Added the show bgp vpnv4 unicast command. |
5.2(1) |
S Commands |
Added the show bgp vpnv6 unicast command. |
5.2(1) |
S Commands |
Local AS (BGP) Support |
Added the local-as (bgp) command. |
5.2(1) |
L Commands |
Passive Interface Support |
Added the passive-interface command |
5.2(1) |
P Commands |
Peer Gateway Exclude VLAN Support |
Added the peer-gateway exclude-vlan command. |
5.2(1) |
P Commands |
Route Policy Manager |
Added the set interface command. |
5.2(1) |
S Commands |
|
Added the set extcommunity cost command. |
5.2(1) |
|
Added the set extcommunity rt command. |
5.2(1) |
Added the set nssa-only command. |
5.2(1) |
Added the set extcommunity cost command. |
5.2(1) |
|
Added the hardware ip glean throttle maximum command. |
5.1(1) |
|
Glean Throttle |
Added the hardware ip glean throttle command. |
5.1(1) |
H Commands |
|
Added the hardware ip glean throttle timeout command. |
5.1(1) |
|
Added the hardware ip glean throttle syslog command. |
5.1(1) |
Added the show ip arp summary command. |
5.1(1) |
Show Commands |
Added the show ip adjacency summary command. |
5.1(1) |
Added the show ip adjacency throttle statistics command. |
5.1(1) |
L3 Routing |
Added the hardware proxy layer-3 forwarding command. |
5.1(1) |
H Commands |
|
Added the show hardware proxy layer-3 detail command. |
5.1(1) |
Show Commands |
|
Added the show hardware proxy layer-3 counters command. |
5.1(1) |
|
Added the clear hardware proxy layer-3 counters command. |
5.1(1) |
C Commands |
WCCP Enhancement |
Added the hia-timeout keyword to the syntax description. |
5.1(1) |
H Commands |
Added the show running-config wccp command. |
5.1(1) |
Show Commands |
Added the show version internal build-identifier command. |
5.1(1) |
GLBP |
Added the GLBP extended timer commands. |
5.0(2) |
G Commands |
Route Policy Manager |
Added the match mac-list , mac-list , and match vlan commands. |
5.0(2) |
M Commands |
FIB |
Deprecated the hardware forwarding dynamic-allocation command. |
5.0 |
H Commands |
Deprecated the show hardware forwarding dynamic-allocation status command. |
5.0 |
Show Commands |
BGP |
Added advertise-map, nexthop trigger-delay, nexthop route-map, low-memory exempt and extended community commands. |
4.2(1) |
A Commands L Commands N Commands Show Commands |
EIGRP, IS-IS |
Added redistribute maximum-prefix commands. |
4.2(1) |
L Commands |
OSPF |
Added ip router ospf multi-area, ipv6 router ospfv3 multi-area, and redistribute maximum-prefix commands. |
4.2(1) |
I Commands L Commands |
Route Policy Manager |
Added ip extcommunity, match extcommunity, set extcommunity, and set excomm-delete commands. |
4.2(1) |
I Commands M Commands S Commands |
WCCP |
Added WCCPv2 commands. |
4.2(1) |
C Commands I Commands Show Commands |
HSRP |
Added threshold support for priority (HSRP) command. |
4.1(3) |
P Commands |
IP |
Changed platform ip verify commands to hardware ip verify commands. |
4.1(3) |
H Commands P Commands |
EIGRP |
Added IPv6 commands. |
4.1(2) |
A Commands C Commands I Commands Show Commands |
Object Tracking |
Added ipv6 keyword to track and show track commands. |
4.1(2) |
T Commands Show Commands |
EIGRP |
Removed the eigrp keyword from graceful-restart, log-adjacency-changes, and log-neighbor-warnings commands. Replaced the policy keyword with route-map keyword in the show ip eigrp policy statistics and clear ip eigrp policy statistics redistribute commands. Removed the nsf command. Added authentication key-chain (EIGRP and authentication mode (EIGRP) to support authentication in a VRF. Added the clear ip eigrp accounting and clear ip eigrp traffic commands. |
4.0(3) |
A Commands C Commands E Commands N Commands Show Commands |
ARP |
Added the ip arp gratuitous command. |
4.0(3) |
I Commands |
BGP local AS number |
Added local-as command. |
4.0(3) |
L Commands |
EIGRP maximum paths |
Modified maximum-paths (EIGRP) command default to 8. |
4.0(2) |
M Commands |