Catalyst 4500 Series Switch Software Configuration Guide, Release IOS XE 3.4.xSG and IOS 15.1(2)SGx

Configuring Cisco IOS Auto Smartport Macros

This chapter describes how to configure and apply Auto Smartport macros on the Catalyst 4500 series switch.

This chapter includes the following major sections:

•About Auto Smartport Macros

•Configuring Auto Smartport Macros

•Displaying Auto Smartport

Note For complete syntax and usage information for the switch commands used in this chapter, first look at the Cisco Catalyst 4500 Series Switch Command Reference and related publications at this location:

http://www.cisco.com/en/US/products//hw/switches/ps4324/index.html

If the command is not found in the Catalyst 4500 Series Switch Command Reference, it will be found in the larger Cisco IOS library. Refer to the Cisco IOS Command Reference and related publications at this location:

http://www.cisco.com/en/US/products/ps6350/index.html

About Auto Smartport Macros

Auto Smartport macros dynamically configure ports based on the device type detected on the port. When the switch detects a new device on a port, it applies the appropriate Auto Smartport macro. When a link-down event occurs on the port, the switch removes the macro. For example, when you connect a Cisco IP phone to a port, Auto Smartport automatically applies the Cisco IP phone macro. The Cisco IP phone macro enables quality of service (QoS), security features, and a dedicated voice VLAN to ensure proper treatment of delay-sensitive voice traffic.

Auto Smartport uses event triggers to map devices to macros. The most common event triggers are based on Cisco Discovery Protocol (CDP) messages received from connected devices. The detection of a device (Cisco IP phone, Cisco wireless access point, Cisco switch, or Cisco router) invokes an event trigger for that device.

Link Layer Discovery Protocol (LLDP) is used to detect devices that do not support CDP. Other mechanisms used as event triggers include the 802.1X authentication result and MAC-address learned.

System built-in event triggers exist for various devices based mostly on CDP and LLDP messages (Table 20-1) and some MAC address.and some MAC address. (Through Cisco IOS Release 12.2(54)SG, DMP is detected using the MAC address. Starting with Cisco IOS Release 15.0(2)SG, DMP is also detected using CDP.) These triggers are enabled as long as Auto Smartport is enabled.

You can also define your own trigger. User-defined triggers can be CDP/LLDP-based, a group of MAC addresses, or the value of the attribute-value (AV) pair for the auto-smart-port keyword.

The Auto Smartport macros are groups of CLI commands. Detection of devices on a port triggers the application of the macro for the device. (For example, detecting a CISCO_PHONE event on a port triggers the switch to apply the commands in the CISCO_PHONE_AUTO_SMARTPORT macro.) System built-in macros exist for various devices, and, by default, system built-in triggers are mapped to the corresponding built-in macros. You can change the mapping of built-in triggers or macros as needed.

A macro basically applies or removes a set of CLIs on an interface based on the link status. In a macro, the link status is checked. If the link is up, then a set of CLIs is applied; if the link is down, the set is removed (the no format of the CLIs are applied). The part of the macro that applies the set of CLIs is termed macro. The part that removes the CLIs (the no format of the CLIs) are termed antimacro.

Besides creating user-defined triggers, you can also create user-defined macros and map one to the other among all triggers (both built-in and user-defined) and all macros (both built-in and user-defined). Use the Cisco IOS scripting capability to create the macros. Cisco IOS scripting is a BASH-like language syntax for command automation and variable replacement.

The four detection mechanisms adhere to the following order of priority:

•If 802.1X authentication is configured on a port, an authentication response-based trigger is applied, and other triggers are ignored.

•If 802.1X authentication fails and the CDP/LLDP fallback mechanism is configured, CDP/LLDP triggers for phone devices only; if no fallback mechanism is configured, or a device is not a phone device, nothing is triggered.

•If 802.1X authentication is configured on a port, a MAC address-based trigger is never triggered.

•If 802.1X authentication is not configured on a port, CDP/LLDP has priority over a MAC address-based trigger with a hold-off timer applied for MAC-address based trigger. Between CDP/LLDP, there is no particular order; whichever one arrives first is triggered.

Device Classifier

Starting with Cisco Release IOS XE 3.3.0SG and IOS 15.1(1)SG, the device classifier (DC) feature is enabled by default on the Catalyst 4500 series switch.

The DC collects information from MAC-OUI and protocols such as CDP, LLDP, and DHCP to identify devices. You must enable CDP and LLDP on the switch. To make DHCP options information available to the DC, you must enable the DHCP snooping feature on the switch. The device attributes collected from these protocols are evaluated against a set of profiles available to the DC to find the best match. The best-matched profile is used for device identification.

Devices that do not send CDP, LLDP or DHCP traffic may not be properly identified by the device classifier.

Device-classifier uses profile definitions—built-in and default profiles. The built-in profiles contain the device profiles that are known to the Auto Smartport module, comprising a limited set of Cisco devices. They are built into Cisco IOS and cannot be changed. The default profiles are stored as a text file in nonvolatile storage and allow the DC to identify a much larger set of devices. The default profiles are updated as part of the Cisco IOS archive download.

When a new device is detected, the corresponding shell trigger executes the Auto Smartport configuration macro. Auto Smartport has built-in mappings for a large set of devices. You can use the commands described in the "Configuring Mapping Between User-Defined Triggers and Built-in Macros" section to create new mappings. You can create the trigger mappings based on the profile name or device name that is provided by the DC.

Device Visibility Mode

The DC function is enabled on the switch by default. You can disable it by using the no macro auto monitor global configuration command. The DC feature provides show commands to display the devices that are connected to the switch. It also provides information about the physical port to which the device is connected, along with device MAC address and other vendor information. Only directly connected devices, such as another Layer 2 switch, are classified on nonaccess ports. On access ports that are connected to hubs, device classification is limited to 32 devices.

When you enable Auto Smartport, the DC is automatically enabled.

Configuring Auto Smartport Macros

The following topics are included:

•Enabling Auto Smartport Macros

•Auto Smartport Configuration Guidelines

•Configuring Auto Smartport Built-in Macro Parameters

•Configuring User-Defined Event Triggers

•Configuring Mapping Between User-Defined Triggers and Built-in Macros

•Configuring Auto Smartport User-Defined Macros

Enabling Auto Smartport Macros

Note By default, Auto Smartport is disabled globally. To disable Auto Smartport macros on a specific port, use the no macro auto global processing interface command before enabling Auto Smartport globally.

To enable Auto Smartport globally, use the macro auto global processing global configuration command.

To enable Auto Smartport macros, perform this task:

Switch# configure terminal

Switch(config)# [no] macro auto 
global processing [cdp | lldp]

Switch(config)# end

Switch# show running-config

Switch# copy running-config 
startup-config

Use the show shell functions and the show shell triggers privileged EXEC command to display the event triggers, the built-in macros, and the built-in macro default values.

This example shows how enable Auto Smartport on the switch and how to disable the feature on a specific interface:

Switch(config)# macro auto global processing

Switch(config)# interface interface_id

Switch(config-if)# no macro auto processing

Auto Smartport Default Configuration

By default, Cisco IOS shell is enabled and Auto Smartport is disabled globally.

Table 20-1 shows the Auto Smartport built-in event triggers that are embedded in the switch software by default.

Table 20-2 shows the Auto Smartport built-in macros that are embedded in the switch software.

Note By default, the built-in event triggers are mapped to the built-in macros.

Auto Smartport Configuration Guidelines

Auto Smartport guidelines include the following:

•To avoid system conflicts when Auto Smartport macros are applied, remove all port configuration except for 802.1X authentication.

•If the macro conflicts with the original configuration, some macro commands might not be applied, or some antimacro commands might not be applied. (The antimacro is the portion of the applied macro that removes it at link down.)

Note Failure of one command in the macro halts the application of the entire macro.

For example, if 802.1X authentication is enabled, you cannot remove switchport-mode access configuration. You must remove the 802.1X authentication before removing the configuration.

•A port should not be a member of an EtherChannel when applying Auto Smartport macros.

If Auto Smartport is not yet enabled globally, disable Auto Smartport on all the EtherChannel ports before enabling it globally. If Auto Smartport is already enabled, shut down the port and disable it before adding the port to an EtherChannel.

Note If an Auto Smartport macro is applied on an interface, EtherChannel configuration usually fails because of conflict with the auto-QoS configuration applied by the macro.

•The built-in macro default data VLAN is VLAN 1. The default voice VLAN is VLAN 2. You should modify the built-in macro default values if your switch uses different VLANs. To view all built-in macro default values, use the show shell functions privileged EXEC command.

•To detect non-Cisco devices for 802.1X authentication or MAB, configure the RADIUS server to support the Cisco AV pair auto-smart-port=event trigger. You must configure a user-defined trigger with the value returned in the AV pair for auto-smart-port.

•For stationary devices that do not support CDP, MAB, or 802.1X authentication, such as network printers, we recommend that you disable Auto Smartport on the port.

•If authentication is enabled on a port, the switch ignores CDP unless the fallback cdp keyword is in the macro auto global processing global configuration command.

•The order of CLI commands within the macro and the corresponding antimacro can differ.

•Before converting a port into an Layer 3 interface, enter the no macro auto processing command. This prevents Auto Smartport from applying macros on the interface. If Layer 3 is already configured, enter the no macro auto processing command on the Layer 3 interface enable Auto Smartport globally.

•Auto Smartport macros and Smartport cannot coexist on an interface.

•A switch applies a macro in accordance with the LLDP advertisement from the attached device. If the device does not identify itself properly, the wrong macro is applied. Consult the specific device documentation to ensure the device's firmware is current.

•The LWAP's WLC software version must be 6.0.188 ( => Cisco IOS 12.4(21a)JA2) or later to make it detectable as LWAP by AutoSmartport.

•As of Cisco IOS Release 12.2(54)SG, Auto Smartport does not support macros that apply EtherChannel configurations. Interfaces that belong to EtherChannel groups are treated as standard interfaces. You can apply macros on individual interfaces based on the device type but the CLIs in the macro (for example, auto-QoS) might conflict with an EtherChannel configuration. We recommend that you disable Auto Smartport on interfaces belonging to EtherChannels before you enable Auto Smartport globally. If Auto Smartport is already enabled, disable Auto Smartport on the interfaces before configuring EtherChannel.

Configuring Auto Smartport Built-in Macro Parameters

The switch automatically maps from built-in event triggers to built-in macros. You can replace the built-in macro default values with values that are specific to your switch.

To configure Auto Smartport built-in macros parameters, perform this task:

Switch# configure terminal

Switch(config)# macro auto execute 
event trigger builtin built-in 
macro name [parameter=value] 
[parameter=value]

Switch(config)# end

Switch# show running-config

Switch# copy running-config 
startup-config

The no macro auto execute event trigger {[builtin built-in macro name [parameter=value]] | [[parameter=value] {function contents}]} command deletes the mapping.

This example shows how to use two built-in Auto Smartport macros for connecting Cisco switches and Cisco IP phones to the switch. This example modifies the default voice VLAN, access VLAN, and native VLAN for the trunk interface:

Switch# configure terminal

Switch(config)# macro auto execute CISCO_PHONE_EVENT builtin CISCO_PHONE_AUTO_SMARTPORT 
ACCESS_VLAN=10 VOICE_VLAN=20

Switch(config)#

Switch(config)#

Switch(config)#!!! the next command enables auto smart ports globally

Switch(config)# macro auto global processing fallback cdp

Switch(config)#

Switch(config)# exit

Switch#

Switch# show running-config interface gigabitethernet2/7

Building configuration...

Current configuration : 284 bytes

!

switchport access vlan 10

switchport mode access

switchport voice vlan 2

switchport port-security maximum 2

switchport port-security

switchport port-security aging time 2

switchport port-security violation restrict

switchport port-security aging type inactivity

auto qos voip cisco-phone 

qos trust device cisco-phone

neighbor device type phone

macro description CISCO_PHONE_EVENT

spanning-tree portfast

spanning-tree bpduguard enable

service-policy input AutoQos-VoIP-Input-Cos-Policy

service-policy output AutoQos-VoIP-Output-Policy

end

Note You can also use the macro auto device command to simplify changing the parameters for a built-in functions for a device type.

Configuring User-Defined Event Triggers

You can configure two types of event triggers: user-defined and MAC address-based.

The following sections describe these triggers:

•802.1X-Based Event Trigger

•MAC Address-Based Event Trigger

802.1X-Based Event Trigger

When using MAB or 802.1X authentication to trigger Auto Smartport macros, you need to create an event trigger that corresponds to the Cisco AV pair (auto-smart-port=event trigger) sent by the RADIUS server.

To configure an event trigger, perform this task:

Switch# configure terminal

Switch(config)# shell trigger 
identifier description

Switch(config)# end

Switch# show shell triggers

Switch# copy running-config 
startup-config

Use the no shell trigger identifier global configuration command to delete the event trigger.

The following example shows how to define a user-defined trigger:

Switch# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# shell trigger RADIUS_MAB_EVENT MAC_AuthBypass Event 

Switch(config)#

MAC Address-Based Event Trigger

To configure a MAC address group as an event trigger, perform this task:

Switch# configure terminal

Switch(config)# macro auto 
mac-address group

Switch(config)# end 

Switch# show shell triggers

Switch# copy running-config 
startup-config

Use the no macro auto mac-address-group grp_name to delete the event trigger.

Configuring Mapping Between User-Defined Triggers and Built-in Macros

You need to map the user-defined trigger to either a built-in macro or user-defined macro.

To map a user-defined trigger to a built-in macros, perform this task:

Switch# configure terminal

Switch(config)# macro auto execute 
event trigger builtin built-in macro 
name [parameter=value] 
[parameter=value]

Switch(config)# end 

Switch# show shell triggers

Switch# copy running-config 
startup-config

This example shows how to map a user-defined event trigger called RADIUS_MAB_EVENT to the built-in macro CISCO_PHONE_AUTO_SMARTPORT with access VLAN set to 10, and how to verify the entries.

This procedure shows how to map a user-defined trigger to a built-in macro:

Step 1 Connect the device to a MAB-enabled switch port.

Step 2 On the RADIUS server, set the attribute-value pair to auto-smart-port=RADIUS_MAB_EVENT.

Step 3 On the switch, create the event trigger RADIUS_MAB_EVENT.

The switch recognizes the attribute-value pair=RADIUS_MAB_EVENT response from the RADIUS server and applies the macro CISCO_PHONE_AUTO_SMARTPORT, as in the following example:

Switch(config)# macro auto execute RADIUS_MAB_EVENT builtin CISCO_PHONE_AUTO_SMARTPORT 
ACCESS_VLAN=10

Switch(config)# exit

Switch# show shell triggers 

User defined triggers

---------------------

Trigger Id: RADIUS_MAB_EVENT

Trigger description: MAC_AuthBypass Event 

Trigger environment: 

Trigger mapping function: CISCO_PHONE_AUTO_SMARTPORT

<output truncated>

Configuring Auto Smartport User-Defined Macros

The Cisco IOS shell provides basic scripting capabilities for configuring the user-defined Auto Smartport macros. These macros can contain multiple lines and can include any CLI command. You can also define variable substitution, conditionals, functions, and triggers within the macro.

Inside a user-defined macro, besides parameters specified through macro auto execute trigger parameter-name=value .., you also can use the following variables published by EEM (Table 20-3):

To map an event trigger to a user-defined macro, perform this task:

Switch# configure terminal

Switch(config)# macro auto 
execute event trigger 
[parameter=value] {function 
contents}

Switch(config)# end

Switch# show running-config

Switch# copy running-config 
startup-config

This example shows how to map a user-defined event trigger called Cisco Digital Media Player (DMP) to a user-defined macro.

Step 1 Connect the DMP to an 802.1X- or MAB-enabled switch port.

Step 2 On the RADIUS server, set the attribute-value pair to auto-smart-port =MY_MEDIAPLAYER_EVENT.

Step 3 On the switch, create the event trigger CISCO_DMP_EVENT, and map it to the user-defined macro commands shown below.

The switch recognizes the attribute-value pair=CISCO_DMP_EVENT response from the RADIUS server and applies the macro associated with this event trigger.

The following example shows the macro portion of the automacro:

Switch(config)# shell trigger CISCO_DMP_EVENT Cisco DMP player

Switch(config)# macro auto execute CISCO_DMP_EVENT { 

if [[ $LINKUP -eq YES ]]; then 

conf t 

 interface $INTERFACE 

   macro description $TRIGGER 

   switchport access vlan 1 

   switchport mode access 

   switchport port-security 

   switchport port-security maximum 1 

   switchport port-security violation restrict 

   switchport port-security aging time 2 

   switchport port-security aging type inactivity 

   spanning-tree portfast 

   spanning-tree bpduguard enable 

   exit 

fi 

The following represents the anti-macro portion of the automacro:

if [[ $LINKUP -eq NO ]]; then 

conf t 

interface $INTERFACE 

     no macro description $TRIGGER 

     no switchport access vlan 1 

     if [[ $AUTH_ENABLED -eq NO ]]; then 

        no switchport mode access 

     fi 

     no switchport port-security 

     no switchport port-security maximum 1 

     no switchport port-security violation restrict 

     no switchport port-security aging time 2 

     no switchport port-security aging type inactivity 

     no spanning-tree portfast 

     no spanning-tree bpduguard enable 

     exit 

fi

}

Switch(config)# end

Table 20-4 lists the supported shell keywords your can apply in your macros and antimacro statements.

Table 20-5 lists the shell keywords that are not supported in macros and antimacros.

Displaying Auto Smartport

To display the Auto Smartport and static Smartport macros, use one or more of the privileged EXEC commands in Table 20-6.

show macro auto monitor clients

show macro auto monitor device

show macro auto monitor type

show parser macro

show parser macro name macro-name

show parser macro brief

show parser macro description [interface 
interface-id]

show shell

This example shows how to use the show macro auto monitor device privileged EXEC command with the optional mac-address keyword to view summary information about the connected device with the specified MAC address:

Switch# show macro auto monitor device mac-address 001f.9e90.1250

MAC_Address       Port_Id     Profile Name

==============    =======     ============================

001f.9e90.1250    Gi1/0/4    Cisco-AP-Aironet-1130

==========================================================

This example shows how to use the show macro auto monitor type privileged EXEC command with no optional keywords to view the devices recognized by the device classifier:

Switch# show macro auto monitor type table

  Valid         Type       Profile Name                         min Conf   ID 

===========  =========  ==================                      ========  ====

  Valid        Default      Apple-Device                              10        0    

  Valid        Default      Aruba-Device                              10        1    

  Valid        Default      Avaya-Device                              10        2    

  Valid        Default      Avaya-IP-Phone                            20        3    

  Valid        Default      BlackBerry                                20        4    

  Valid        Default      Cisco-Device                              10        5    

  Valid        Default      Cisco-IP-Phone                            20        6    

  Valid        Default      Cisco-IP-Phone-7902                       70        7    

  Valid        Default      Cisco-IP-Phone-7905                       70        8    

  Valid        Default      Cisco-IP-Phone-7906                       70        9    

  Valid        Default      Cisco-IP-Phone-7910                       70        10   

  Valid        Default      Cisco-IP-Phone-7911                       70        11   

  Valid        Default      Cisco-IP-Phone-7912                       70        12   

  Valid        Default      Cisco-IP-Phone-7940                       70        13   

  Valid        Default      Cisco-IP-Phone-7941                       70        14   

  Valid        Default      Cisco-IP-Phone-7942                       70        15   

  Valid        Default      Cisco-IP-Phone-7945                       70        16   

  Valid        Default      Cisco-IP-Phone-7945G                      70        17   

  Valid        Default      Cisco-IP-Phone-7960                       70        18   

  Valid        Default      Cisco-IP-Phone-7961                       70        19   

  Valid        Default      Cisco-IP-Phone-7962                       70        20   

  Valid        Default      Cisco-IP-Phone-7965                       70        21   

  Valid        Default      Cisco-IP-Phone-7970                       70        22   

  Valid        Default      Cisco-IP-Phone-7971                       70        23   

  Valid        Default      Cisco-IP-Phone-7975                       70        24   

  Valid        Default      Cisco-IP-Phone-7985                       70        25   

  Valid        Default      Cisco-IP-Phone-9971                       70        26   

  Valid        Default      Cisco-WLC-2100-Series                     40        27   

  Valid        Default      DLink-Device                              10        28   

  Valid        Default      Enterasys-Device                          10        29   

  Valid        Default      HP-Device                                 10        30   

  Valid        Default      HP-JetDirect-Printer                      30        31   

  Valid        Default      Lexmark-Device                            10        32   

  Valid        Default      Lexmark-Printer-E260dn                    30        33   

  Valid        Default      Microsoft-Device                          10        34   

  Valid        Default      Netgear-Device                            10        35   

  Valid        Default      NintendoWII                               10        36   

  Valid        Default      Nortel-Device                             10        37   

  Valid        Default      Nortel-IP-Phone-2000-Series               20        38   

  Valid        Default      SonyPS3                                   10        39   

  Valid        Default      XBOX360                                   20        40   

  Valid        Default      Xerox-Device                              10        41   

  Valid        Default      Xerox-Printer-Phaser3250                  30        42   

  Valid        Default      Aruba-AP                                  20        43   

  Valid        Default      Cisco-Access-Point                        10        44   

  Valid        Default      Cisco-IP-Conference-Station-7935          70        45   

  Valid        Default      Cisco-IP-Conference-Station-7936          70        46   

  Valid        Default      Cisco-IP-Conference-Station-7937          70        47   

  Valid        Default      DLink-DAP-1522                            20        48   

  Valid        Default      Cisco-AP-Aironet-1130                     30        49   

  Valid        Default      Cisco-AP-Aironet-1240                     30        50   

  Valid        Default      Cisco-AP-Aironet-1250                     30        51   

  Valid        Default      Cisco-AIR-LAP                             25        52   

  Valid        Default      Cisco-AIR-LAP-1130                        30        53   

  Valid        Default      Cisco-AIR-LAP-1240                        50        54   

  Valid        Default      Cisco-AIR-LAP-1250                        50        55   

  Valid        Default      Cisco-AIR-AP                              25        56   

  Valid        Default      Cisco-AIR-AP-1130                         30        57   

  Valid        Default      Cisco-AIR-AP-1240                         50        58   

  Valid        Default      Cisco-AIR-AP-1250                         50        59   

  Invalid      Default      Sun-Workstation                           10        60   

  Valid        Default      Linksys-Device                            20        61   

  Valid        Default      LinksysWAP54G-Device                      30        62   

  Valid        Default      HTC-Device                                10        63   

  Valid        Default      MotorolaMobile-Device                     10        64   

  Valid        Default      VMWare-Device                             10        65   

  Valid        Default      ISE-Appliance                             10        66   

  Valid        Built-in     Cisco-Device                              10        0    

  Valid        Built-in     Cisco-Router                              10        1    

  Valid        Built-in     Router                                    10        2    

  Valid        Built-in     Cisco-IP-Camera                           10        3    

  Valid        Built-in     Cisco-IP-Camera-2xxx                      30        4    

  Valid        Built-in     Cisco-IP-Camera-2421                      50        5    

  Valid        Built-in     Cisco-IP-Camera-2500                      50        6    

  Valid        Built-in     Cisco-IP-Camera-2520                      50        7    

  Valid        Built-in     Cisco-IP-Camera-2530                      50        8    

  Valid        Built-in     Cisco-IP-Camera-4xxx                      50        9    

  Valid        Built-in     Cisco-Transparent-Bridge                  8         10   

  Valid        Built-in     Transparent-Bridge                        8         11   

  Valid        Built-in     Cisco-Source-Bridge                       10        12   

  Valid        Built-in     Cisco-Switch                              10        13   

  Valid        Built-in     Cisco-IP-Phone                            20        14   

  Valid        Built-in     IP-Phone                                  20        15   

  Valid        Built-in     Cisco-DMP                                 10        16   

  Valid        Built-in     Cisco-DMP-4305G                           70        17   

  Valid        Built-in     Cisco-DMP-4310G                           70        18   

  Valid        Built-in     Cisco-DMP-4400G                           70        19   

  Valid        Built-in     Cisco-WLC-2100-Series                     40        20   

  Valid        Built-in     Cisco-Access-Point                        10        21   

  Valid        Built-in     Cisco-AIR-LAP                             30        22   

  Valid        Built-in     Cisco-AIR-AP                              30        23   

  Valid        Built-in     Linksys-Device                            20        24 

This example shows how to use the show shell triggers privileged EXEC command to view the event triggers in the switch software:

Switch# show shell triggers

User defined triggers

---------------------

Built-in triggers

-----------------

Trigger Id: CISCO_PHONE_EVENT

Trigger description: Event for ip-phone macro

Trigger environment: ACCESS_VLAN=1 VOICE_VLAN=2

Trigger mapping function: CISCO_PHONE_AUTO_SMARTPORT

Trigger Id: CISCO_ROUTER_EVENT

Trigger description: Event for router macro

Trigger environment: NATIVE_VLAN=1

Trigger mapping function: CISCO_ROUTER_AUTO_SMARTPORT

Trigger Id: CISCO_SWITCH_EVENT

Trigger description: Event for switch macro

Trigger environment: NATIVE_VLAN=1

Trigger mapping function: CISCO_SWITCH_AUTO_SMARTPORT

Trigger Id: CISCO_WIRELESS_AP_EVENT

Trigger description: Event for Wireless Access Point macro

Trigger environment: NATIVE_VLAN=1

Trigger mapping function: CISCO_AP_AUTO_SMARTPORT

Trigger Id: CISCO_WIRELESS_LIGHTWEIGHT_AP_EVENT

Trigger description: Event for Wireless Lightweight Access Point macro

Trigger environment: NATIVE_VLAN=1

Trigger mapping function: CISCO_LWAP_AUTO_SMARTPORT

This example shows how to use the show shell functions privileged EXEC command to view the built-in macros in the switch software:

Switch# show shell functions 

#User defined functions:

#Built-in functions:

function CISCO_AP_AUTO_SMARTPORT () {

    if [[ $LINKUP -eq YES ]]; then

        conf t

            interface  $INTERFACE

                macro description $TRIGGER

                switchport trunk encapsulation dot1q

                switchport trunk native vlan $NATIVE_VLAN

                switchport trunk allowed vlan ALL

                switchport mode trunk

                switchport nonegotiate

                auto qos voip trust

                mls qos trust cos

            exit

        end

    fi

    if [[ $LINKUP -eq NO ]]; then

        conf t

            interface  $INTERFACE

                no macro description

                no switchport nonegotiate

                no switchport trunk native vlan $NATIVE_VLAN

                no switchport trunk allowed vlan ALL

                no auto qos voip trust

                no mls qos trust cos

                if [[ $AUTH_ENABLED -eq NO ]]; then

                    no switchport mode

                    no switchport trunk encapsulation

                fi

            exit

        end

    fi

} 

function CISCO_SWITCH_AUTO_SMARTPORT () {

    if [[ $LINKUP -eq YES ]]; then

        conf t

            interface  $INTERFACE

                macro description $TRIGGER

                auto qos voip trust

                switchport trunk encapsulation dot1q

                switchport trunk native vlan $NATIVE_VLAN

                switchport trunk allowed vlan ALL

                switchport mode trunk

            exit

        end

    else

         conf t

             interface  $INTERFACE

                 no macro description

                 no auto qos voip trust

                 no switchport mode trunk

                 no switchport trunk encapsulation dot1q

                 no switchport trunk native vlan $NATIVE_VLAN

                 no switchport trunk allowed vlan ALL

             exit

         end

    fi

} 

<output truncated>