Configuring VTP


This chapter describes how to configure the VLAN Trunking Protocol (VTP) in Cisco IOS Release 12.2SX.


Note For complete syntax and usage information for the commands used in this chapter, see the Cisco IOS Master Command List, at this URL:

http://www.cisco.com/en/US/docs/ios/mcl/allreleasemcl/all_book.html



Tip For additional information about Cisco Catalyst 6500 Series Switches (including configuration examples and troubleshooting information), see the documents listed on this page:

http://www.cisco.com/en/US/products/hw/switches/ps708/tsd_products_support_series_home.html

Participate in the Technical Documentation Ideas forum


This chapter consists of these sections:

Understanding VTP

VLAN Interaction

VTP Default Configuration

VTP Configuration Guidelines and Restrictions

Configuring VTP

Understanding VTP

VTP is a Layer 2 messaging protocol that maintains VLAN configuration consistency by managing the addition, deletion, and renaming of VLANs within a VTP domain. A VTP domain (also called a VLAN management domain) is made up of one or more network devices that share the same VTP domain name and that are interconnected with trunks. VTP minimizes misconfigurations and configuration inconsistencies that can result in a number of problems, such as duplicate VLAN names, incorrect VLAN-type specifications, and security violations. Before you create VLANs, you must decide whether to use VTP in your network. With VTP, you can make configuration changes centrally on one or more network devices and have those changes automatically communicated to all the other network devices in the network.


Note For complete information on configuring VLANs, see Chapter 23 "Configuring VLANs."


These sections describe how VTP works:

Understanding the VTP Domain

Understanding VTP Modes

Understanding VTP Advertisements

Understanding VTP Authentication

Understanding VTP Version 2

Understanding VTP Version 3

Understanding VTP Pruning

Understanding the VTP Domain

A VTP domain (also called a VLAN management domain) is made up of one or more interconnected network devices that share the same VTP domain name. A network device can be configured to be in one and only one VTP domain. You make global VLAN configuration changes for the domain using either the command-line interface (CLI) or Simple Network Management Protocol (SNMP).

VTP server mode is the default and the switch is in the no-management domain state until it receives an advertisement for a domain over a trunk link or you configure a management domain.

If the switch receives a VTP advertisement over a trunk link, it inherits the management domain name and the VTP configuration revision number. The switch ignores advertisements with a different management domain name or an earlier configuration revision number.

If you configure the switch as VTP transparent, you can create and modify VLANs but the changes affect only the individual switch. The valid VLAN ranges are as follows:

VTP version 1 and version 2 support VLANs 1 to 1000 only.

In Cisco IOS Release 12.2(33)SXI and later releases, VTP version 3 is supported. In VTP version 3, the entire VLAN range is supported (VLANs 1 to 4094).

The pruning of VLANs still applies to VLANs 1 to 1000 only.

Extended-range VLANs are supported only in VTP version 3. If converting from VTP version 3 to VTP version 2, VLANs in the range 1006 to 4094 are removed from VTP control.

By default, all devices come up as secondary servers. You can enter the vtp primary privileged EXEC mode command to specify a primary server.

In Cisco IOS releases prior to Release 12.2(33)SXI, when using VTP version 1 and version 2, a VTP server is used to back up the database to the NVRAM and allows you to change the database information.

In Cisco IOS Release 12.2(33)SXI and later releases, VTP version 3 is supported. In VTP version 3, there is a VTP-primary server and a VTP-secondary server. A primary server allows you to alter the database information and the database updates sent out are honored by all the devices in the system. A secondary server can only back up the updated VTP configuration received from the primary server in the NVRAMs. The status of the primary and secondary servers is a runtime status and is not configurable.

VTP maps VLANs dynamically across multiple LAN types with unique names and internal index associations. Mapping eliminates excessive device administration required from network administrators.

Understanding VTP Modes

You can configure any one of these VTP modes:

Server—In VTP server mode, you can create, modify, and delete VLANs and specify other configuration parameters (such as VTP version and VTP pruning) for the entire VTP domain. VTP servers advertise their VLAN configuration to other network devices in the same VTP domain and synchronize their VLAN configuration with other network devices based on advertisements received over trunk links. VTP server is the default mode.

Client—VTP clients behave the same way as VTP servers, but you cannot create, change, or delete VLANs on a VTP client.

Transparent—VTP transparent network devices do not participate in VTP. A VTP transparent network device does not advertise its VLAN configuration and does not synchronize its VLAN configuration based on received advertisements. However, in VTP version 2, a transparent network device will forward received VTP advertisements from its trunking LAN ports. In VTP version 3, a transparent network device is specific to an instance.

Off—In VTP off mode, a network device functions in the same manner as a VTP transparent device except that it does not forward VTP advertisements.


Note The VTP server mode automatically changes from VTP server mode to VTP client mode if the switch detects a failure while writing configuration to NVRAM. If this happens, the switch cannot be returned to VTP server mode until the NVRAM is functioning.


Understanding VTP Advertisements

Each network device in the VTP domain sends periodic advertisements out each trunking LAN port to a reserved multicast address. VTP advertisements are received by neighboring network devices, which update their VTP and VLAN configurations as necessary.

The following global configuration information is distributed in VTP version 1 and version 2 advertisements:

VLAN IDs (ISL and 802.1Q).

Emulated LAN names (for ATM LANE).

802.10 SAID values (FDDI).

VTP domain name.

VTP configuration revision number.

VLAN configuration, including the maximum transmission unit (MTU) size for each VLAN.

Frame format.

In VTP version 3, the information distributed in VTP version 1 and version 2 advertisements are supported, as well as the following information:

A primary server ID.

An instance number.

A start index.

An advertisement request is sent by a Client or a Server in these situations:

On a trunk coming up on a switch with an invalid database.

On all trunks when the database of a switch becomes invalid as a result of a configuration change or a takeover message.

On a specific trunk where a superior database has been advertised.

VTP version 3 adds the following fields to the subset advertisement request:

A primary server ID.

An instance number.

A window size.

A start index.

Understanding VTP Authentication

In releases prior to Cisco IOS Release 12.2(33)SXI, the secret that is used to validate the received VTP updates is visible in plain text in the show commands and the NVRAM file, const_nvram:vlan.dat. In the event that a device in a VTP domain is compromised, the administrator had to change the VTP secret across all the devices in the VTP domain.

In Cisco IOS Release 12.2(33)SXI and later releases, VTP version 3 is supported. In VTP version 3, you can configure the authentication password to be hidden using the vtp password command. When you configure the authentication password to be hidden, it does not appear in plain text in the configuration. Instead, the secret associated with the password is saved in hexadecimal format in the running configuration. The password-string argument is an ASCII string from 1 to 64 characters identifying the administrative domain for the device.

Understanding VTP Version 2

If you use VTP in your network, you must decide whether to use VTP version 1 or version 2.


Note If you are using VTP in a Token Ring environment, you must use version 2.


VTP version 2 supports the following features not supported in version 1:

Token Ring support—VTP version 2 supports Token Ring LAN switching and VLANs (Token Ring Bridge Relay Function [TrBRF] and Token Ring Concentrator Relay Function [TrCRF]). For more information about Token Ring VLANs, see the "Understanding VLANs" section.

Unrecognized Type-Length-Value (TLV) Support—A VTP server or client propagates configuration changes to its other trunks, even for TLVs that it is not able to parse. The unrecognized TLV is saved in NVRAM.

Version-Dependent Transparent Mode—In VTP version 1, a VTP transparent network device inspects VTP messages for the domain name and version and forwards a message only if the version and domain name match. Because only one domain is supported, VTP version 2 forwards VTP messages in transparent mode without checking the version.

Consistency Checks—In VTP version 2, VLAN consistency checks (such as VLAN names and values) are performed only when you enter new information through the CLI or SNMP. Consistency checks are not performed when new information is obtained from a VTP message, or when information is read from NVRAM. If the digest on a received VTP message is correct, its information is accepted without consistency checks.

Understanding VTP Version 3


Note If you are using VTP in a Token Ring environment, you must use version 2.


In Cisco IOS Release 12.2(33)SXI and later releases, VTP version 3 is supported. VTP version 3 supports all the features in version 1 and version 2. VTP version 3 also supports the following features not supported in version 1 and version 2:

Enhanced authentication—In VTP version 3, you can configure the authentication password to be hidden using the vtp password command. When you configure the authentication password to be hidden, it does not appear in plain text in the configuration. Instead, the secret associated with the password is saved in hexadecimal format in the running configuration. The password-string argument is an ASCII string from 1 to 64 characters identifying the administrative domain for the device.

The hidden and secret keywords for VTP password are supported only in VTP version 3. If converting to VTP version 2 from VTP version 3, you must remove the hidden or secret keyword prior to the conversion. These keywords are supported on the Catalyst 6500 series switch only.

Support for extended range VLAN database propagation—VTP version 1 and version 2 support VLANs 1 to 1000 only. In VTP version 3, the entire VLAN range is supported (VLANs 1 to 4094). The pruning of VLANs still applies to VLANs 1 to 1000 only. Extended-range VLANs are supported in VTP version 3 only. Private VLANs are supported in VTP version 3. If you convert from VTP version 3 to VTP version 2, the VLANs in the range 1006 to 4094 are removed from VTP control.

VLANs 1002 to 1005 are reserved VLANs in VTP version 1, version 2, and version 3.

Support for propagation of any database in a domain—In VTP version 1 and version 2, a VTP server is used to back up the database to the NVRAM and allows you to change the database information.


Note In Cisco IOS Release 12.2(33)SXI and later releases, VTP version 3 supports Multiple Spanning Tree (802.1s) (MST) database propagation separate from the VLAN database only. In the MST database propagation, there is a VTP primary server and a VTP econdary server. A primary server allows you to alter the database information, and the database updates sent out are honored by all the devices in the system. A secondary server can only back up the updated VTP configuration received from the primary server in the NVRAMs. The status of the primary and secondary servers is a runtime status and is not configurable.


By default, all devices come up as secondary servers. You can enter the vtp primary privileged EXEC mode command to specify a primary server.

The primary-server status is needed only when database changes have to be performed and is obtained when the administrator issues a takeover message in the domain. The primary-server status is lost when you reload, switch over, or the domain parameters change. The secondary servers back up the configuration and continue to propagate the database. You can have a working VTP domain without any primary servers. Primary and secondary servers may exist on an instance in the domain.

In VTP version 3, there is no longer a restriction to propagate only VLAN database information. You can use VTP version 3 to propagate any database information across the VTP domain. A separate instance of the protocol is running for each application that uses VTP.

Two VTP version 3 regions can only communicate over a VTP version 1 or VTP version 2 region in transparent mode.

CLI to turn off/on VTP on a per-trunk basis—You can enable VTP on a per-trunk basis using the vtp interface configuration mode command. You can disable VTP on a per-trunk basis using the no form of this command. When you disable VTP on the trunking port, all the VTP instances for that port are disabled. You will not be provided with the option of setting VTP to OFF for the MST database and ON for the VLAN database.

VTP on a global basis—When you set VTP mode to OFF globally, this applies to all the trunking ports in the system. Unlike the per-port configuration, you can specify the OFF option on a per-VTP instance basis. For example, the system could be configured as VTP-server for the VLAN database and as VTP-off for the MST database. In this case, VLAN databases are propagated by VTP, MST updates are sent out on the trunk ports in the system, and the MST updates received by the system are discarded.

Understanding VTP Pruning

VTP pruning enhances network bandwidth use by reducing unnecessary flooded traffic, such as broadcast, multicast, unknown, and flooded unicast packets. VTP pruning increases available bandwidth by restricting flooded traffic to those trunk links that the traffic must use to access the appropriate network devices. By default, VTP pruning is disabled.

In VTP versions 1 and 2, when you enable or disable pruning, it is propagated to the entire domain and accepted by all the devices in that domain. In VTP version 3, the domain administrator must manually enable or disable VTP pruning explicitly on each device.

For VTP pruning to be effective, all devices in the management domain must support VTP pruning. On devices that do not support VTP pruning, you must manually configure the VLANs allowed on trunks.

Figure 22-1 shows a switched network without VTP pruning enabled. Interface 1 on network Switch 1 and port 2 on Switch 4 are assigned to the Red VLAN. A broadcast is sent from the host connected to Switch 1. Switch 1 floods the broadcast, and every network device in the network receives it, even though Switches 3, 5, and 6 have no ports in the Red VLAN.

You enable pruning globally on the switch (see the "Enabling VTP Pruning" section). You configure pruning on Layer 2 trunking LAN ports (see the "Configuring a Layer 2 Switching Port as a Trunk" section).

Figure 22-1 Flooding Traffic without VTP Pruning

Figure 22-2 shows the same switched network with VTP pruning enabled. The broadcast traffic from Switch 1 is not forwarded to Switches 3, 5, and 6 because traffic for the Red VLAN has been pruned on the links indicated (port 5 on Switch 2 and port 4 on Switch 4).

Figure 22-2 Flooding Traffic with VTP Pruning

Enabling VTP pruning on a VTP server enables pruning for the entire management domain. VTP pruning takes effect several seconds after you enable it. By default, VLANs 2 through 1000 are pruning eligible. VTP pruning does not prune traffic from pruning-ineligible VLANs. VLAN 1 is always pruning ineligible; traffic from VLAN 1 cannot be pruned.

To configure VTP pruning on a trunking LAN port, use the switchport trunk pruning vlan command (see the "Configuring a Layer 2 Switching Port as a Trunk" section). VTP pruning operates when a LAN port is trunking. You can set VLAN pruning eligibility when VTP pruning is enabled or disabled for the VTP domain, when any given VLAN exists or not, and when the LAN port is currently trunking or not.

VLAN Interaction

This section describes the VLAN interaction between devices with different VTP versions:

Interaction Between VTP Version 3 and VTP Version 2 Devices

Interaction Between VTP Version 3 and VTP Version 1 Devices

Interaction Between VTP Version 3 and VTP Version 2 Devices

When a VTP version 3 device on a trunk port receives messages from a VTP version 2 device, the VTP version 3 device sends a scaled-down version of the VLAN database on that particular trunk in a VTP version 2 format. A VTP version 3 device does not send out VTP version 2-formatted packets on a trunk port unless it first receives VTP version 2 packets on that trunk. If the VTP version 3 device does not receive VTP version 2 packets for an interval of time on the trunk port, the VTP version 3 device stops transmitting VTP version 2 packets on that trunk port.

Even when a VTP version 3 device detects a VTP version 2 device on a trunk port, the VTP version 3 device continues to send VTP version 3 packets in addition to VTP version 3 device 2 packets, to allow two kinds of neighbors to coexist on the trunk. VTP version 3 sends VTP version 3 and VTP version 2 updates on VTP version 2-detected trunks.

A VTP version 3 device does not accept configuration from a VTP version 2 (or VTP version 1) device.

Unlike in VTP version 2, when you configure the VTP version to be version 3, version 3 does not configure all the VTP version 3-capable devices in the domain to start behaving as VTP version 3 systems.

Interaction Between VTP Version 3 and VTP Version 1 Devices

When a VTP version 1 device that is capable of VTP version 2 or VTP version 3 receives a VTP version 3 packet, it will be configured as a VTP version 2 device if VTP version 2 conflicts do not exist.

VTP version 1-only capable devices cannot interoperate with VTP version 3 devices.

VTP Default Configuration

Table 22-1 shows the default VTP configuration.

Table 22-1 VTP Default Configuration 

Feature
Default Value

VTP domain name

Null

VTP version 1 and version 2 mode

Server

VTP version 3 mode

The VTP version 3 VLAN database mode is the same as the VLAN database mode in VTP version 1 or 2 after the conversion from VTP version 1 or 2 to VTP version 3. For example, the VTP version 1 or 2 VLAN database mode is carried over to VTP version 3 VLAN database mode.

MST database mode

Transparent

VTP version 3 server type

Secondary

VTP version 2 state

Version 2 is disabled

VTP password

None

VTP pruning

Disabled


VTP Configuration Guidelines and Restrictions

When implementing VTP in your network, follow these guidelines and restrictions:

Supervisor engine redundancy does not support nondefault VLAN data filenames or locations. Do not enter the vtp file file_name command on a switch that has a redundant supervisor engine.

Before installing a redundant supervisor engine, enter the no vtp file command to return to the default configuration.

All network devices in a VTP domain must run the same VTP version.

You must configure a password on each network device in the management domain when in secure mode.


Caution If you configure VTP in secure mode, the management domain will not function properly if you do not assign a management domain password to each network device in the domain.

A VTP version 2-capable network device can operate in the same VTP domain as a network device that runs VTP version 1 if VTP version 2 is disabled on the VTP version 2-capable network device (VTP version 2 is disabled by default).

Do not enable VTP version 2 on a network device unless all of the network devices in the same VTP domain are version 2-capable. When you enable VTP version 2 on a network device, all of the version 2-capable network devices in the domain enable VTP version 2.

In a Token Ring environment, you must enable VTP version 2 for Token Ring VLAN switching to function properly.

When you enable or disable VTP pruning on a VTP server, VTP pruning for the entire management domain is enabled or disabled.

The pruning-eligibility configuration applies globally to all trunks on the switch. You cannot configure pruning eligibility separately for each trunk.

When you configure VLANs as pruning eligible or pruning ineligible, pruning eligibility for those VLANs is affected on that switch only, not on all network devices in the VTP domain.

VTP version 1 and VTP version 2 do not propagate configuration information for extended-range VLANs (VLAN numbers 1006 to 4094). You must configure extended-range VLANs manually on each network device.

VTP version 3 supports extended-range VLANs (VLAN numbers 1006 to 4094). If you convert from VTP version 3 to VTP version 2, the VLANs in the range 1006 to 4094 are removed from VTP control.

VTP version 3 supports propagation of any database in a domain by allowing you to configure a primary and secondary server.

In Cisco IOS Release 12.2(33)SXI and later releases, the network administrator has to manually configure VTP version 3 on the switches that need to run VTP version 3.

Prior to configuring VTP version 3, you must ensure that the spanning-tree extend system-id command has been enabled.

VTP version 3 is not supported on private VLAN (PVLAN) ports.

If there is insufficient DRAM available for use by VTP, the VTP mode changes to transparent.

Network devices in VTP transparent mode do not send VTP Join messages. On trunk connections to network devices in VTP transparent mode, configure the VLANs that are used by the transparent-mode network devices or that need to be carried across trunks as pruning ineligible. For information about configuring prune eligibility, see the "Configuring the List of Prune-Eligible VLANs" section.

Configuring VTP

These sections describe how to configure VTP:

Configuring VTP Global Parameters

Configuring the VTP Mode

Configuring VTP Mode on a Per-Port Basis

Displaying VTP Statistics

Configuring VTP Global Parameters

These sections describe configuring the VTP global parameters:

Configuring VTP Version 1 and Version 2 Passwords

Configuring VTP Version 3 Password

Enabling VTP Pruning

Enabling VTP Version 2

Enabling VTP Version 3


Note You can enter the VTP global parameters in either global configuration mode or in EXEC mode.


Configuring VTP Version 1 and Version 2 Passwords

To configure the VTP version 1 and version 2 global parameters, perform this task:

Command
Purpose

Router(config)# vtp password password-string

Sets a password, which can be from 1 to 64 characters long, for the VTP domain.

Router(config)# no vtp password

Clears the password.


This example shows one way to configure a VTP password in global configuration mode:

Router# configure terminal 
Router(config)# vtp password WATER 
Setting device VLAN database password to WATER.
Router# 
 
   

This example shows how to configure a VTP password in EXEC mode:

Router# vtp password WATER
Setting device VLAN database password to WATER.
Router# 

Note The password is not stored in the running-config file.


Configuring VTP Version 3 Password

To configure the VTP version 3 password, perform this task:

Command
Purpose

Router(config)# vtp password password-string [hidden | secret]

Configures a password, which can be from 1 to 64 characters long or in 32-digit hexadecimal format, for the VTP domain.

Note When entering the secret keyword, the password-string must be entered in 32-digit hexadecimal format.

Router(config)# no vtp password

Clears the password.


This example shows one way to configure a VTP password in global configuration mode:

Router# configure terminal 
Router(config)# vtp password water 
Setting device VTP database password to water.
Router# 
 
   

Note If you configure a VTP password in EXEC mode, the password is not stored in the running-config file.


This example shows one way to configure the password with a hidden key saved in hexadecimal format in the running configuration:

Router# configure terminal 
Router(config)# vtp password 82214640C5D90868B6A0D8103657A721 hidden
Setting device VTP password
Router# 
 
   

This example shows how you configure the password secret key in hexadecimal format:

Router# configure terminal 
Router(config)# vtp password 300F060A2B0601035301020107010201 secret
Setting device VTP password
Router# 

Configuring VTP Version 3 Server Type

To specify a primary server, perform this task:

 
Command
Purpose

Step 1 

Router# vtp primary [vlan | mst] [force]

Configure this device as the primary server.

Step 2 

Router# show vtp status

Verifies the configuration.

The vtp primary command does not have a no form. To return to the secondary server status, one of the following conditions must be met:

System reload.

Switchover between redundant supervisors.

Takeover from another server.

Change in the mode configuration.

Any domain configuration change (version, domain name, domain password).

This example shows how to configure this device as the primary server if the password feature is disabled:

Router# vtp primary
This system is becoming primary server for feature vlan
No conflicting VTP version 3 devices found.
Do you want to continue? [confirm]y
Router#
 
   

This example shows how to configure this device as the primary server for the VTP VLAN feature if the password feature is disabled:

Router# vtp primary vlan
This system is becoming primary server for feature vlan
No conflicting VTP version 3 devices found.
Do you want to continue? [confirm]y
Router#
 
   

This example shows how to force this device to be the primary server for the VTP MST feature if the password feature is disabled:

Router# vtp primary mst force
This system is becoming primary server for feature MST
No conflicting VTP version 3 devices found.
Do you want to continue? [confirm]y
Router#
 
   

This example shows how to force this device to be the primary server for the VTP MST feature when the domain VTP password is set with the hidden or secret keyword:

Router# vtp primary mst force
Enter VTP password: water1
This switch is becoming Primary server for mst feature in the VTP domain
VTP Database Conf Switch ID      Primary Server Revision System Name 
------------ ---- -------------- -------------- -------- --------------------
VLANDB       Yes  00d0.00b8.1400=00d0.00b8.1400 1        stp7 
Do you want to continue (y/n) [n]? y
Router#

Enabling VTP Pruning

To enable VTP pruning in the management domain, perform this task:

 
Command
Purpose

Step 1 

Router(config)# vtp pruning

Enables VTP pruning in the management domain.

Router(config)# no vtp pruning

Disables VTP pruning in the management domain.

Step 2 

Router# show vtp status

Verifies the configuration.

This example shows one way to enable VTP pruning in the management domain:

Router# configure terminal 
Router(config)# vtp pruning
Pruning switched ON
 
   

This example shows how to enable VTP pruning in the management domain with any release:

Router# vtp pruning
Pruning switched ON
 
   

This example shows how to verify the configuration:

Router# show vtp status | include Pruning
VTP Pruning Mode: Enabled
Router# 
 
   

For information about configuring prune eligibility, see the "Configuring the List of Prune-Eligible VLANs" section.

Enabling VTP Version 2

VTP version 2 is disabled by default on VTP version 2-capable network devices. When you enable VTP
version 2 on a network device, every VTP version 2-capable network device in the VTP domain enables version 2.


Caution VTP version 1 and VTP version 2 are not interoperable on network devices in the same VTP domain. Every network device in the VTP domain must use the same VTP version. Do not enable VTP version 2 unless every network device in the VTP domain supports version 2.


Note In a Token Ring environment, you must enable VTP version 2 for Token Ring VLAN switching to function properly on devices that support Token Ring interfaces.


To enable VTP version 2, perform this task:

 
Command
Purpose

Step 1 

Router(config)# vtp version {1 | 2}

Enables VTP version 2.

Router(config)# no vtp version

Reverts to the default (VTP version 1).

Step 2 

Router# show vtp status

Verifies the configuration.

This example shows one way to enable VTP version 2:

Router# configure terminal 
Router(config)# vtp version 2 
V2 mode enabled.
Router(config)# 
 
   

This example shows how to enable VTP version 2 with any release:

Router# vtp version 2 
V2 mode enabled.
Router# 
 
   

This example shows how to verify the configuration:

Router# show vtp status | include V2 
VTP V2 Mode: Enabled
Router# 

Enabling VTP Version 3

VTP version 3 is disabled by default. You can enable version 3 in global configuration mode only. In Cisco IOS Release 12.2(33)SXI and later releases, the network administrator has to manually configure VTP version 3 on the switches that need to run VTP version 3.


Note Prior to configuring VTP version 3, you must ensure that the spanning-tree extend system-id command has been enabled.



Caution In VTP version 3, both the primary and secondary servers may exist on an instance in the domain.

To enable VTP version 3, perform this task:

 
Command
Purpose

Step 1 

Router(config)# vtp version 3

Enables VTP version 3.

Router(config)# no vtp version

Reverts to the default (VTP version 1).

Step 2 

Router# show vtp status

Verifies the configuration.

This example shows one way to enable VTP version 3:

Router# configure terminal 
Router(config)# vtp version 3 
Router(config)# 
 
   

This example shows how to verify the configuration:

Router# show vtp status
VTP Version capable             : 1 to 3
VTP version running             : 3
VTP Domain Name                 : lab_switch
VTP Pruning Mode                : Disabled
VTP Traps Generation            : Disabled
Device ID                       : 0015.c724.0040
 
   
Feature VLAN:
--------------
VTP Operating Mode                : Server
Number of existing VLANs          : 6
Number of existing extended VLANs : 0
Configuration Revision            : 0
Primary ID                        : 0000.0000.0000
Primary Description               :
MD5 digest                        : 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
                                    0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
 
   
 
   
Feature MST:
--------------
VTP Operating Mode                : Transparent
 
   
 
   
Feature UNKNOWN:
--------------
VTP Operating Mode                : Transparent
Router# 

Configuring the VTP Mode

To configure the VTP mode, perform this task:

 
Command
Purpose

Step 1 

Router(config)# vtp mode {client | server | transparent | off} {vlan | mst | unknown}

Configures the VTP mode.

Step 2 

Router(config)# vtp domain domain-name

(Optional for server mode) Defines the VTP domain name, which can be up to 32 characters long. VTP server mode requires a domain name. If the switch has a trunk connection to a VTP domain, the switch learns the domain name from the VTP server in the domain.

Note You cannot clear the domain name.

Step 3 

Router(config)# end

Exits VLAN configuration mode.

Step 4 

Router# show vtp status

Verifies the configuration.


Note When VTP is disabled, you can enter VLAN configuration commands in configuration mode instead of the VLAN database mode and the VLAN configuration is stored in the startup configuration file.


This example shows how to configure the switch as a VTP server:

Router# configuration terminal
Router(config)# vtp mode server
Setting device to VTP SERVER mode.
Router(config)# vtp domain lab_network
Setting VTP domain name to lab_network
Router(config)# end
Router# 
 
   

This example shows how to configure the switch as a VTP client:

Router# configuration terminal
Router(config)# vtp mode client
Setting device to VTP CLIENT mode.
Router(config)# exit
Router# 
 
   

This example shows how to disable VTP on the switch:

Router# configuration terminal
Router(config)# vtp mode transparent
Setting device to VTP TRANSPARENT mode.
Router(config)# end
Router# 
 
   

This example shows how to disable VTP on the switch and to disable VTP advertisement forwarding:

Router# config terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)# vtp mode off
Setting device to VTP OFF mode.
Router(config)# exit
Router#
 
   

This example shows how to verify the configuration:

Router# show vtp status 
VTP Version capable             : 1 to 3
VTP version running             : 3
VTP Domain Name                 : lab_network
VTP Pruning Mode                : Disabled
VTP Traps Generation            : Disabled
Device ID                       : 0015.c724.0040
 
   
Feature VLAN:
--------------
VTP Operating Mode                : Server
Number of existing VLANs          : 6
Number of existing extended VLANs : 0
Configuration Revision            : 0
Primary ID                        : 0000.0000.0000
Primary Description               :
MD5 digest                        : 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
                                    0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
 
   
Feature MST:
--------------
VTP Operating Mode                : Transparent
 
   
Feature UNKNOWN:
--------------
VTP Operating Mode                : Transparent
 
   
Router# 
 
   
 
   

Configuring VTP Mode on a Per-Port Basis

With Release 12.2(33)SXH and later releases, you can configure VTP mode on a per-port basis. The VTP enable value will be applied only when a port becomes switched port in trunk mode. Incoming and outgoing vtp pdus are blocked; not forwarded. With Release 12.2(33)SXI and later releases, in VTP version 3, you can also configure VTP mode on a per-trunk basis. To configure VTP mode, perform this task:

 
Command
Purpose

Step 1 

Router(config)# interface type1  slot/port

Selects an interface to configure.

Step 2 

Router(config-if)# vtp

Enables VTP on the specified port.

Step 3 

Router(config-if)# end

Exits interface configuration mode.

Step 4 

Router# show running-config interface type slot/port

Verifies the change to the port.

Step 5 

Router# show vtp interface

Verifies the configuration.

1 type = fastethernet, gigabitethernet, or tengigabitethernet

This example shows how to configure VTP mode on a port:

Router# config terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)# interface gigabitethernet 3/5
Router(config-if)# vtp
Router(config-if)# end
Router#
 
   

This example shows how to disable VTP mode on a port:

Router# config terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)# interface gigabitethernet 3/5
Router(config-if)# no vtp
Router(config-if)# end
Router#
 
   

This example shows how to verify the configuration change:

Router# show vtp interface gigabitethernet 3/5
 
   
 Interface               VTP Status
------------------------------------
 GigabitEthernet3/5       disabled
Router#
 
   

This example shows how to verify the interface:

Router# show vtp interface
 
   
 Interface               VTP Status
------------------------------------
 GigabitEthernet3/1       enabled
 GigabitEthernet3/2       enabled
 GigabitEthernet3/3       enabled
 GigabitEthernet3/4       enabled
 GigabitEthernet3/5       disabled
 GigabitEthernet3/6       enabled
 ...

Displaying VTP Statistics

To display VTP statistics, including VTP advertisements sent and received and VTP errors, perform this task:

Command
Purpose

Router# show vtp counters

Displays VTP statistics.


This example shows how to display VTP statistics:

Router# show vtp counters
VTP statistics:
Summary advertisements received    : 7
Subset advertisements received     : 5
Request advertisements received    : 0
Summary advertisements transmitted : 997
Subset advertisements transmitted  : 13
Request advertisements transmitted : 3
Number of config revision errors   : 0
Number of config digest errors     : 0
Number of V1 summary errors        : 0
 
   
VTP pruning statistics:
 
   
Trunk            Join Transmitted Join Received    Summary advts received from
                                                   non-pruning-capable device
---------------- ---------------- ---------------- ---------------------------
Fa5/8               43071            42766            5

Tip For additional information about Cisco Catalyst 6500 Series Switches (including configuration examples and troubleshooting information), see the documents listed on this page:

http://www.cisco.com/en/US/products/hw/switches/ps708/tsd_products_support_series_home.html

Participate in the Technical Documentation Ideas forum