Voice Menu Codes
This section contains a quick-reference list of the voice configuration menu options for the Cisco ATA.
This section contains the following tables of voice menu codes:
•Table B-1—Information Options
•Table B-2—Configuration Parameters
•Table B-3—Software Upgrade codes
Note Follow each voice menu code with #.
Note The term Cisco ATA refers to both the Cisco ATA 186 and the Cisco ATA 188, unless otherwise stated.
Table B-1 lists codes to return basic Cisco ATA information.
Table B-1 Cisco ATA Voice Menu Codes—Information Options
|
|
|
Build information |
123123 |
Build date of the Cisco ATA software |
Review IP address |
21 |
Returns IP address of the Cisco ATA |
Review MAC address |
24 |
Returns media access control (MAC) address of the Cisco ATA |
Review network route IP address |
22 |
Returns IP address of the network route |
Review subnet mask |
23 |
Returns subnet mask of the network route |
Version number |
123 |
Returns version number of the Cisco ATA software |
Table B-2 lists configuration codes.
Table B-2 Cisco ATA Voice Menu Codes—Configuration Parameters
|
|
|
Alternate NTP IP address |
78 |
IP address of the alternate NTP server |
Audio mode |
312 |
Allows finer control of the audio component to suit certain user applications |
Call features |
314 |
Subscribed features statically enabled by the user |
Caller ID method |
316 |
Specifies the signal format when generating the Caller ID format to use |
TFTP Configuration Interval |
80002 |
Interval (in seconds) between configuration updates when TFTP configuration is used, |
Connection mode |
311 |
Controls the connection mode of the call signaling protocol |
Dynamic Host Configuration Protocol (DHCP) |
20 |
Controls whether the Cisco ATA can automatically obtain configuration parameters from a server over the network |
DNS 1 IP |
916 |
IP address of the primary DNS server |
DNS 2 IP |
917 |
IP address of the secondary DNS server |
Encrypt key |
320 |
Encrypts the configuration file on the TFTP server |
Gatekeeper/proxy server IP address |
5 |
H.323 gatekeeper IP address |
H.323 protocol |
38 |
Selects the signaling protocol |
IP address |
1 |
IP address of the Cisco ATA |
LBR codec |
300 |
Low bit rate codec selection |
Login ID 0 |
46 |
Alternate user ID used for authentication |
Login ID 1 |
47 |
Alternate user ID used for authentication |
Media port |
202 |
Specifies which base port the Cisco ATA uses to receive RTP media streams |
Network route address |
2 |
Network router address |
NPrintf address |
81 |
IP address of a host to which all Cisco ATA debug messages are sent |
NTP server address |
141 |
IP address of the NTP server |
Num Tx frames |
35 |
Number of frames transmitted per packet |
Paid features |
315 |
Features subscribed to by the user |
Polarity |
304 |
Controls connect and disconnect polarity |
PWD 0 |
4 |
Password associated with the primary phone line (UID0 or LoginID0) |
PWD 1 |
14 |
Password associated with the secondary phone line (UID1 or LoginID1) |
Rx codec |
36 |
Selects the audio codec type to use to decode received data. The call-receiving station automatically adjusts to the call-initiating station's audio codec type if the call-receiving station supports that audio codec. |
Set password |
7387277 |
Configuration interface password |
Signal timers |
318 |
Timeout values controlling the starting or stopping of a signaling event |
H.323 max number of redirects |
205 |
Maximum number of redirections the Cisco ATA will attempt to reach a callee when making a call |
Subnet mask |
10 |
Specifies the subnet mask for the Cisco ATA |
TFTP URL |
905 |
IP address of the TFTP server when TFTP configuration is used |
Timezone |
302 |
Specifies offset to GMT—used to time-stamp incoming calls for caller ID |
ToConfig |
80001 |
Identifies unconfigured or already-configured Cisco ATAs |
Trace Fflags |
313 |
Enables logging of debug information |
Tx Codec |
37 |
Selects transmitting audio codec preference |
UDP TOS bits |
255 |
Determines the precedence and delay of UDP IP packets |
UID 0 |
3 |
User ID (telephone number) for the PHONE 1 port |
UID 1 |
13 |
User ID (telephone number) for the PHONE 2 port |
Use login ID |
93 |
Determines which pair (UIDx, PWDx or LoginIDx, PWDx) to use for authentication |
Use TFTP |
305 |
Enables TFTP as configuration method |
Table B-3 lists codes used in the software upgrade process. For information about these codes, see "Upgrading the Cisco ATA Signaling Image."
Table B-3 Cisco ATA Voice Menu Codes—Software Upgrade
|
|
|
Upgrade software |
100 |
Used in the software process to enter the IP address of the PC |
Upgrade language to English |
101 |
When upgrading software, changes or upgrades the voice prompt language to English |