Configuring the Half-Height Gigabit Ethernet Line Card for the Cisco uBR10012 Universal Broadband Router

Available Languages

Download Options

  • PDF     (249.8 KB)
    View with Adobe Reader on a variety of devices
Updated:November 30, 2012

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Configuring the Half-Height Gigabit Ethernet Line Card for the Cisco uBR10012 Universal Broadband Router

Table Of Contents

Configuring the Half-Height Gigabit Ethernet Line Card for the Cisco uBR10012 Universal Broadband Router

Contents

Prerequisites for Configuring the Half-Height Gigabit Ethernet Line Card

Restrictions for Configuring the Half-Height Gigabit Ethernet Line Card

Information About the Half-Height Gigabit Ethernet Line Card

Benefits

Feature Overview

Faceplate and LEDs

LEDs

SFP Gigabit Ethernet Interface Converter Modules and Cable Specifications

Gigabit Ethernet Line Card Default Values

Half-Height Gigabit Ethernet Line Card Syntax

How to Configure the Half-Height Gigabit Ethernet Line Card

Configuring the Interface

Prerequisites

Restrictions

Example

Enabling Auto-Negotiation

Prerequisites

Restrictions

Example

Assigning a MAC Address

Prerequisites

Restrictions

Example

Setting and Changing Loopback Mode

Prerequisites

Restrictions

Example

Enabling IEEE 802.1Q Encapsulation

Prerequisites

Restrictions

Example

Setting the Maximum Transmission Unit

Prerequisites

Restrictions

Example

Command Examples

show interfaces

show controllers

show running config

Upgrading to a Half-Height Gigabit Ethernet Line Card

Additional References

Related Documents

Standards

MIBs

RFCs

Command Reference

Obtaining Documentation and Submitting a Service Request


Configuring the Half-Height Gigabit Ethernet Line Card for the Cisco uBR10012 Universal Broadband Router

This document describes procedures and Cisco IOS commands for configuring and monitoring the Half-Height Gigabit Ethernet (HHGE) line card in the Cisco uBR10012 router.

History for the Half-Height Gigabit Ethernet Line Card Feature Cisco uBR10012 Universal Broadband Router

Release
Modification

12.3(21)BC1

Support for the GLC-T SFP module.

12.3(13)BC

This feature was introduced.


Finding Support Information for Platforms and Cisco IOS Software Images

Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image support. Access Cisco Feature Navigator at http://www.cisco.com/go/fn. You must have an account on Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear.

Contents

•Prerequisites for Configuring the Half-Height Gigabit Ethernet Line Card

•Restrictions for Configuring the Half-Height Gigabit Ethernet Line Card

•Information About the Half-Height Gigabit Ethernet Line Card

•How to Configure the Half-Height Gigabit Ethernet Line Card

•Command Examples

•Upgrading to a Half-Height Gigabit Ethernet Line Card

•Additional References

•Command Reference

•Obtaining Documentation and Submitting a Service Request

Prerequisites for Configuring the Half-Height Gigabit Ethernet Line Card

To use the HHGE line card, you must ensure the following:

•Cisco IOS Release 12.3(13)BC or later release is installed on your system.

•A Cisco Performance Routing Engine 2 (PRE2) module is installed in the router.

Restrictions for Configuring the Half-Height Gigabit Ethernet Line Card

The following restrictions apply to the HHGE line card:

•It must be used with a PRE2 module.

•It must be placed only in slot 3 and slot 4 in the Cisco uBR10012 universal broadband router. Using slots 1 and slot 2 causes a conflict with the Timing, Communication, and Control Plus (TCC+) modules.

Information About the Half-Height Gigabit Ethernet Line Card

This section describes the Cisco Half-Height Gigabit Ethernet line card.

Benefits

The HHGE provides the following benefits to cable Multiple Service Operators (MSOs), service providers, and their partners and customers:

•Provides 1-port full- duplex 1-Gbps data rate

•Supports EtherChannel network

•Supports OIR for 1000BASE-SX or 1000BASE-LX GBICs, as described in the IEEE 802.3z specifications

•Provides redundant trunks in one chassis slot

•Increases throughput density and load balancing, which enhances high availability

•Supports trunk redundancy in a single slot, which frees up a slot for additional subscriber cards

Feature Overview

The HHGE line card (see Figure 1) contains a single Gigabit Ethernet port that provides a trunk uplink to switches and core routers. The HHGE line card provides the Cisco uBR10012 universal broadband router with an IEEE 802.3z- compliant Ethernet interface that can run up to 1 Gbps in full-duplex mode. The line card uses a small form-factor pluggable (SFP) GigaBit Interface Converter (GBIC) module and supports a variety of Gigabit Ethernet interface types (SX, LX/LH, and ZX), which you can change or upgrade at any time.

Faceplate and LEDs

Figure 1 Half-Height Gigabit Ethernet Line Card Faceplate

1

Ejector levers

4

SFP Gigabit Interface Converter

2

FAIL LED (yellow)

5

Link status LED (green)

3

Receive packet LED (green)

6

Transmit packet LED (green)


LEDs

This HHGE line card faceplate contains the following LEDs that continuously indicate line card status as well as the status of the port during operation (see Figure 1):

•FAIL (yellow)—This LED lights during portions of the POST (Power-On Self Test), but remains off after the POST on a properly working line card. If the line card fails during operation, this LED lights and an alarm event occurs.

The FAIL LED blinks during the following SFP GBIC faults:

–An SFP GBIC other than a Cisco brand is inserted.

–A non-Gigabit Ethernet SFP GBIC is inserted.

–A hardware problem occurs in a valid SFP GBIC.

•LINK (green)—When on, this LED indicates that a carrier signal exists. If negotiation is enabled (at both ends), it indicates successful completion and the port can pass traffic.

Note This LED can also be on if the line card is in internal loopback.

When off, this LED indicates that no carrier signal is detected, negotiation failed, or the port is administratively down.

•RX (green)—When on, this status LED indicates that packets are being received. When this LED is off, the line card is not receiving packets.

•TX (green)—When on, this status LED indicates that packets are being transmitted. When this LED is off, the line card is not transmitting packets.

Note Because this line card operates in full-duplex mode, both the RX and TX LEDs can be on at the same time.

SFP Gigabit Ethernet Interface Converter Modules and Cable Specifications

The HHGE line card supports single Ethernet interfaces based on SFP GBIC technology. The following SFPs are supported by this line card:

•1000BASE-SX SFP—The SFP-GE-S, 1000BASE-SX SFP operates on ordinary multimode fiber optic link spans of up to 550 meters in length.

•1000BASE-LX/LH SFP—The SFP-GE-L, 1000BASE-LX/LH SFP operates on ordinary single-mode fiber optic link spans of up to 10,000 meters in length.

•1000BASE-ZX SFP—The GLC-ZX-SM, 1000BASE-ZX SFP operates on ordinary single-mode fiber optic link spans of up to 70 kilometers (km) in length. Link spans of up to 100 km are possible using premium single-mode fiber or dispersion-shifted single-mode fiber. The SFP provides an optical link budget of 23 dB—the precise link span length depends on multiple factors such as fiber quality, number of splices, and connectors.

When shorter distances of single-mode fiber are used, it may be necessary to insert an inline optical attenuator in the link, to avoid overloading the receiver. A 5-decibel (dB) or 10-dB inline optical attenuator should be inserted between the fiber optic cable plant and the receiving port on the GLC-ZX-SM at each end of the link whenever the fiber optic cable span is less than 25 km.

•1000BASE-T SFP— Support for the GLC-T, 1000BASE-T SFP module was introduced in Cisco IOS Release 12.3(23)BC1.

The Cisco GLC-T, 1000BASE-T SFP module connects a Gigabit Interface Converter (GBIC) port to Category 5 wiring via a standard RJ-45 interface. The maximum Category 5 wiring distance is 100 m. The module provides with an option of connecting to a backhaul network interface. For more information on the Cisco GLC-T 1000BASE-T SFP, see Gigabit Interface Converter (GBIC) Module and Small Form-Factor Pluggable (SFP) GBIC Module Install. Info. and Specifications http://www.cisco.com/en/US/docs/routers/7200/install_and_upgrade/gbic_sfp_modules_install/5067g.html

Note The required line card SFP GBIC is shipped already installed in the line card. Cisco sells individual SFP GBICs separately and you can change the type of Gigabit Ethernet interface supported by this line card by simply changing its SFP GBIC.

Table 1 lists the interface types supported by the HHGE line card.

Activation

Table 1 GBIC Port Cabling Specifications

SFP GBIC
Wavelength
(nm)
Fiber Type
Core Size
(microns)
Modal Bandwidth
(MHz/km)
Cable Distance

1000BASE-SX
SFP-GE-S

850

MMF

62.5
62.5
50.0
50.0

160
200
400
500

722 ft (220 m)
902 ft (275 m)
1640 ft (500 m)
1804 ft (550 m)

1000BASE-LX/LH
SFP-GE-L

1300

MMF1


SMF

62.5
50.0
50.0
8 to 10

500
400
500
—

1804 ft (550 m)
1804 ft (550 m)
1804 ft (550 m)
32,808 ft (10 km)

1000BASE-ZX
GLC-ZX-SM

1550

SMF

9, 10

—

43.4 to 62 miles
(70 to 100 km)2

1000BASE-T

GLC-T

NA

NA

NA

NA

328 ft (100 m)

1 A mode-conditioning patch cord is required. Using an ordinary patch cord with MMF, 1000BASE-LX/LH SFP modules, and a short link distance (ten meters) can cause transceiver saturation resulting in an elevated bit error rate (BER). In addition, when using the LX/LH SFP module with 62.5-micron diameter MMF, you must install a mode-conditioning patch cord between the SFP module and the MMF cable on both the transmit and receive ends of the link. The mode-conditioning patch cord is required for link distances greater than 984 ft (300 m).

2 The 1000BASE-ZX SFP module can reach up to 100 km by using dispersion-shifted SMF or low attenuation SMF; the distance depends on fiber quality, number of splices, and connectors.


For more information about the SFPs, see the following URL: http://www.cisco.com/en/US/products/hw/modules/ps5000/tsd_products_support_series_home.html

Gigabit Ethernet Line Card Default Values

Table 2 lists default values for the Gigabit Ethernet line cards. Table 2 includes the command used for modifying a default value and indicates if a value needs to be the same (or opposite) on the remote end of the connection.

Table 2 Gigabit Ethernet Line Card Defaults

Command Name
Default Setting
Command Syntax
Remote Side Setting

auto-negotiation

Enabled

[no] negotiation auto

Same

mtu

1500 (half-height)

mtu [bytes]

Same


Half-Height Gigabit Ethernet Line Card Syntax

To specify an interface number in a configuration command, use the syntax in Table 3 to identify interfaces on the HHGE line cards.

Table 3 HHGE Interface Syntax

Card
Slot
Subslot
Port

HHGE

3 and 4

0 and 1

0


The following example shows the syntax for configuring an HHGE line card in slot 3: 

Router(config)# interface GigabitEthernet 3/0/0

How to Configure the Half-Height Gigabit Ethernet Line Card

The following sections describe configuration commands used for configuring the HHGE line card.

•Configuring the Interface

•Enabling Auto-Negotiation

•Assigning a MAC Address

•Setting and Changing Loopback Mode

•Enabling IEEE 802.1Q Encapsulation

•Setting the Maximum Transmission Unit

Configuring the Interface

Use the following procedure to create a basic configuration (enabling an interface and specifying IP routing) for a Gigabit Ethernet interface. Be prepared with the information you need, such as the interface IP address.

Prerequisites

Cisco IOS Release 12.3(21)BC1 or later release

Restrictions

The HHGE must be in slots 3/0/0, 3/1/0, 4/0/0, or 4/1/0.

SUMMARY STEPS

1. enable

2. configure terminal

3. interface gigabitethernet [slot/subslot/port]

4. ip address [xxx.xxx.xxx.xx]

5. end

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

interface gigabitethernet [slot/subslot/port]

Example:

Router#(config t) interface gigabitethernet 3/0/0

Selects the interface slot, subslot, and port, and enters interface configuration mode.

Step 4 

ip address [xxx.xxx.xxx.xx xxx.xxx.xxx.x]

Example:

Router(config-if)# ip address 192.168.172.12 255.255.255.0

Assigns an IP address and subnet mask to the interface.

Step 5 

end

Example:

Router(config-if)# end

Exits the configuration mode.

Example

The following example defines the initial steps for configuring the HHGE interface: 

Router# configure terminal

Router(config)# interface gigabitethernet 3/0/0

Router(config-if)# ip address 192.168.172.12 255.255.255.0 

Router(config-if)# end

 
   
 
     
    
    
   
 Enabling Auto-Negotiation 
 
    
   
 To set auto-negotiation mode for a Gigabit Ethernet interface, use the negotiation auto command. 
 
    
   
 To remove auto-negotiation, use the no form of the command. 
 
    
   
 Selecting the no negotiation auto command causes the interface to enter a state called force-link-up. 
 
     
    
   
 Prerequisites 
 
    
   
 None 
 
     
    
   
 Restrictions 
 
    
   
 None 
 
     
    
   
 SUMMARY STEPS 
 
    
   
  1. enable 
 
    
   
  2. configure terminal 
 
    
   
  3. interface gigabitethernet [slot/subslot/port] 
 
    
   
  4. negotiation auto 
 
    
   
  5. end 
 
     
    
   
 DETAILED STEPS 
 
    
   
 
 
   
 
    
 
      
      
      
 
         
        
        

          Command or Action 
        
 		 
        
        

          Purpose 
        
 		 
      
 
      
 
       
 Step 1  
 		 
       
enable 
 
        

          Example: 
        
 
Router> enable 
 
       
 Enables privileged EXEC mode. 
 
 •Enter your password if prompted. 
 		 
      
 
      
 
       
 Step 2  
 		 
       
configure terminal 
 
        

          Example: 
        
 
Router# configure terminal 
 
       
 Enters global configuration mode. 
 		 
      
 
      
 
       
 Step 3  
 		 
       
interface gigabitethernet [slot/subslot/port] 
 
        

          Example: 
        
 
Router(config)# interface gigabitethernet 3/0/0 
 
       
 Selects the slot, subslot, and port to configure, and enters interface configuration mode. 
 		 
      
 
      
 
       
 Step 4  
 		 
       
negotiation auto 
 
        

          Example: 
        
 
router(config-if)# negotiation auto 
 
       
 Selects auto-negotiation. 
 
 If necessary, modify the HHGE line card configuration or that of the remote device to ensure that, where appropriate, they use the same settings. For more information, refer to Table 2. 
 		 
      
 
      
 
       
 Step 5  
 		 
       
end 
 
        

          Example: 
        
 
Router(config-if)# end 
 
       
 Exits the configuration mode. 
 		 
      
 
      
    
 
   
 
   
 
 
     
    
   
 Example 
 
    
   
 The following example defines auto-negotiation mode for a Gigabit Ethernet interface: 
 
    
   
 
    
Router# configure terminal

 
   
 
    
   
 
    
Router(config)# interface gigabitethernet 3/0/0

 
   
 
    
   
 
    
Router(config-if)# negotiation auto

 
   
 
    
   
 
    
Router(config-if)# end

 
   
 
    
   
 
    
 
   
 
     
    
    
   
 Assigning a MAC Address 
 
    
   
 Use the mac-address command to preserve a MAC address when you move a line card to a new slot or chassis. You may want to preserve the MAC address if you have an access list that refers to it. If you use this command, you should change the address on the original slot so that you do not have two slots with the same address. 
 
    
   
 To assign a user- defined MAC address for a Gigabit Ethernet interface, use the mac-address command. To remove the user-defined MAC address, use the no form of the command. 
 
    
   
 mac-address address 
 
    
   
 The address variable is a two-byte hexadecimal value. 
 
     
    
   
 Prerequisites 
 
    
   
 None 
 
     
    
   
 Restrictions 
 
    
   
 None 
 
     
    
   
 SUMMARY STEPS 
 
    
   
  1. configure terminal 
 
    
   
  2. interface gigabitethernet [slot/subslot/port] 
 
    
   
  3. mac-address address 
 
    
   
  4. end 
 
     
    
   
 DETAILED STEPS 
 
    
   
 
 
   
 
    
 
      
      
      
 
         
        
        

          Command or Action 
        
 		 
        
        

          Purpose 
        
 		 
      
 
      
 
       
 Step 1  
 		 
       
configure terminal 
 
        

          Example: 
        
 
Router# configure terminal 
 
       
 Enters global configuration mode. 
 		 
      
 
      
 
       
 Step 2  
 		 
       
interface gigabitethernet [slot/subslot/port] 
 
        

          Example: 
        
 
Router(config)# interface gigabitethernet 3/0/0 
 
       
 Defines the slot address where the MAC is applied. 
 		 
      
 
      
 
       
 Step 3  
 		 
       
mac-address address 
 
        

          Example: 
        
 
Router(config-if)# mac-address 6000.0001.0003 
 
       
 Defines the MAC address. 
 		 
      
 
      
 
       
 Step 4  
 		 
       
end 
 
        

          Example: 
        
 
Router(config-if)# end 
 
       
 Exits the configuration mode. 
 		 
      
 
      
    
 
   
 
   
 
 
     
    
   
 Example 
 
    
   
 The following example defines a MAC address for a Gigabit Ethernet interface: 
 
    
   
 
    
Router# configure terminal

 
   
 
    
   
 
    
Router(config)# interface gigabitethernet 3/0/0

 
   
 
    
   
 
    
Router(config-if)# mac-address 6000.0001.0003

 
   
 
    
   
 
    
Router(config-if)# end

 
   
 
    
   
 
    
 
   
 
     
    
    
   
 Setting and Changing Loopback Mode 
 
    
   
 To set loopback mode for a Gigabit Ethernet interface, use the loopback command. To remove loopback mode, use the no form of the command. 
 
    
   
 loopback [internal | external 
 
    
   
 Where: 
 
    
   
 •external runs a loopback that requires a loopback connector. 
 
    
   
 •internal runs a loopback at the MAC controller. 
 
     
    
   
 Prerequisites 
 
    
   
 None 
 
     
    
   
 Restrictions 
 
    
   
 None 
 
     
    
   
 SUMMARY STEPS 
 
    
   
  1. configure terminal 
 
    
   
  2. interface gigabitethernet [slot/subslot/port] 
 
    
   
  3. loopback [internal | external] 
 
    
   
  4. end 
 
     
    
   
 DETAILED STEPS 
 
    
   
 
 
   
 
    
 
      
      
      
 
         
        
        

          Command or Action 
        
 		 
        
        

          Purpose 
        
 		 
      
 
      
 
       
 Step 1  
 		 
       
configure terminal 
 
        

          Example: 
        
 
Router# configure terminal 
 
       
 Enters global configuration mode. 
 		 
      
 
      
 
       
 Step 2  
 		 
       
interface gigabitethernet [slot/subslot/port] 
 
        

          Example: 
        
 
Router(config)# interface gigabitethernet 3/0/0 
 
       
 Enters interface configuration mode. 
 		 
      
 
      
 
       
 Step 3  
 		 
       
loopback [internal | external] 
 
        

          Example: 
        
 
Router(config-if)# loopback internal 
 
       
 Sets loopback mode for the interface, where: 
 
 •internal runs a loopback at the MAC controller. 
 
 •external runs a loopback that requires a loopback connector. 
 		 
      
 
      
 
       
 Step 4  
 		 
       
end 
 
        

          Example: 
        
 
Router(config-if)# end 
 
       
 Exits the configuration mode. 
 		 
      
 
      
    
 
   
 
   
 
 
     
    
   
 Example 
 
    
   
 The following example defines an internal loopback mode for a Gigabit Ethernet interface: 
 
    
   
 
    
Router# configure terminal

 
   
 
    
   
 
    
Router(config)# interface gigabitethernet 3/0/0

 
   
 
    
   
 
    
Router(config-if)# loopback internal

 
   
 
    
   
 
    
Router(config-if)# end

 
   
 
    
   
 
    
 
   
 
     
    
    
   
 Enabling IEEE 802.1Q Encapsulation 
 
    
   
 To enable IEEE 802.1Q encapsulation of traffic on a Gigabit Ethernet interface, use the encapsulation dot1q command. To remove IEEE 802.1Q encapsulation, use the no form of the command. 
 
    
   
 encapsulation dot1q vlan-id 
 
     
    
   
 Prerequisites 
 
    
   
 None 
 
     
    
   
 Restrictions 
 
    
   
 None 
 
     
    
   
 SUMMARY STEPS 
 
    
   
  1. configure terminal 
 
    
   
  2. interface gigabitethernet [slot/subslot/port] 
 
    
   
  3. encapsulation dot1q vlan-id 
 
    
   
  4. end 
 
     
    
   
 DETAILED STEPS 
 
    
   
 
 
   
 
    
 
      
      
      
 
         
        
        

          Command or Action 
        
 		 
        
        

          Purpose 
        
 		 
      
 
      
 
       
 Step 1  
 		 
       
configure terminal 
 
        

          Example: 
        
 
Router# configure terminal 
 
       
 Enters global configuration mode. 
 		 
      
 
      
 
       
 Step 2  
 		 
       
interface gigabitethernet [slot/subslot/port] 
 
        

          Example: 
        
 
Router(config)# interface gigabitethernet 3/0/0 
 
       
 Enters interface configuration mode. 
 		 
      
 
      
 
       
 Step 3  
 		 
       
encapsulation dot1q vlan-id 
 
        

          Example: 
        
 
Router(config-if)# encapsulation dot1q 101 
 
       
 Enables IEEE 802.1Q encapsulation of traffic onthe interface, where: 
 
 •vlan-id is VLAN identifier. Range is 1 to 1000. 
 		 
      
 
      
 
       
 Step 4  
 		 
       
end 
 
        

          Example: 
        
 
Router(config-if)# end 
 
       
 Exits the configuration mode. 
 		 
      
 
      
    
 
   
 
   
 
 
     
    
   
 Example 
 
    
   
 The following example encapsulates VLAN traffic using the IEEE 802.1Q protocol for VLAN 101 on an HHGE interface: 
 
    
   
 
    
Router# configure terminal

 
   
 
    
   
 
    
Router(config)# interface gigabitethernet 3/0/0

 
   
 
    
   
 
    
Router(config-if)# encapsulation dot1q 101

 
   
 
    
   
 
    
Router(config-if)# end

 
   
 
    
   
 
    
 
   
 
     
    
    
   
 Setting the Maximum Transmission Unit 
 
    
   
 To adjust the maximum transmission unit (MTU) size on a Gigabit Ethernet interface, use the mtu command. Use the no form of this command to restore the MTU value to its original default value of 1500. 
 
    
   
 mtu [bytes] 
 
     
    
   
 Prerequisites 
 
    
   
 None 
 
     
    
   
 Restrictions 
 
    
   
 None 
 
     
    
   
 SUMMARY STEPS 
 
    
   
  1. configure terminal 
 
    
   
  2. interface gigabitethernet [slot/subslot/port] 
 
    
   
  3. mtu [bytes] 
 
    
   
  4. end 
 
     
    
   
 DETAILED STEPS 
 
    
   
 
 
   
 
    
 
      
      
      
 
         
        
        

          Command or Action 
        
 		 
        
        

          Purpose 
        
 		 
      
 
      
 
       
 Step 1  
 		 
       
configure terminal 
 
        

          Example: 
        
 
Router# configure terminal 
 
       
 Enters global configuration mode. 
 		 
      
 
      
 
       
 Step 2  
 		 
       
interface gigabitethernet [slot/subslot/port] 
 
        

          Example: 
        
 
Router(config)# interface gigabitethernet 3/0/0 
 
       
 Enters interface configuration mode. 
 		 
      
 
      
 
       
 Step 3  
 		 
       
mtu [bytes] 
 
        

          Example: 
        
 
Router(config-if)# mtu 4470 
 
       
 Sets maximum transmission unit (MTU), where: 
 
 •bytes specifies the size in bytes. Range is 1500 to 4470. 
 
 If necessary, modify the HHGE line card configuration or that of the remote device to ensure that, where appropriate, they use the same settings. For more information, refer to Table 2. 
 		 
      
 
      
 
       
 Step 4  
 		 
       
end 
 
        

          Example: 
        
 
Router(config-if)# end 
 
       
 Exits the configuration mode. 
 		 
      
 
      
    
 
   
 
   
 
 
     
    
   
 Example 
 
    
   
 The following example sets the MTU to 4470 on a Gigabit Ethernet interface: 
 
    
   
 
    
Router# configure terminal

 
   
 
    
   
 
    
Router(config)# interface gigabitethernet 3/0/0

 
   
 
    
   
 
    
Router(config-if)# mtu 4470

 
   
 
    
   
 
    
Router(config-if)# end

 
   
 
    
   
 
    
 
   
 
     
    
    
   
 Command Examples 
 
    
   
 The following examples include: 
 
    
   
 •show interfaces 
 
    
   
 •show controllers 
 
    
   
 •show running config 
 
     
    
    
   
 show interfaces 
 
    
   
 The show interfaces gigabitethernet command is used to indicate the type of Gigabit Ethernet line card installed, and the media type. 
 
    
   
 
    
Router# show interfaces gigabitethernet 4/0/0

 
   
 
    
   
 
    
GigabitEthernet4/0/0 is up, line protocol is up 

 
   
 
    
   
 
    
  Hardware is Half-height Gigabit Ethernet MAC Controller, address is 0005.00e3.fd00

 
   
 
    
   
 
    
  Internet address is 40.1.1.1/16

 
   
 
    
   
 
    
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, 

 
   
 
    
   
 
    
          reliability 255/255, txload 1/255, rxload 2/255

 
   
 
    
   
 
    
  Encapsulation ARPA, loopback not set

 
   
 
    
   
 
    
  Keepalive set (10 sec)

 
   
 
    
   
 
    
  Full-duplex, 1000Mb/s, link type is autonegotiation, media type is SX

 
   
 
    
   
 
    
  output flow-control is XOFF, input flow-control is XOFF

 
   
 
    
   
 
    
  ARP type: ARPA, ARP Timeout 04:00:00

 
   
 
    
   
 
    
  Last input 00:00:07, output 00:00:03, output hang never

 
   
 
    
   
 
    
  Last clearing of "show interface" counters 01:09:13

 
   
 
    
   
 
    
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

 
   
 
    
   
 
    
  Queueing strategy: fifo

 
   
 
    
   
 
    
  Output queue: 0/40 (size/max)

 
   
 
    
   
 
    
  30 second input rate 9613000 bits/sec, 20029 packets/sec

 
   
 
    
   
 
    
  30 second output rate 452000 bits/sec, 884 packets/sec

 
   
 
    
   
 
    
     73181143 packets input, 95919224 bytes, 0 no buffer

 
   
 
    
   
 
    
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

 
   
 
    
   
 
    
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

 
   
 
    
   
 
    
     0 watchdog, 69 multicast, 0 pause input

 
   
 
    
   
 
    
     0 input packets with dribble condition detected

 
   
 
    
   
 
    
     44824427 packets output, 2868784657 bytes, 0 underruns

 
   
 
    
   
 
    
     0 output errors, 0 collisions, 0 interface resets

 
   
 
    
   
 
    
     0 babbles, 0 late collision, 0 deferred

 
   
 
    
   
 
    
     0 lost carrier, 0 no carrier, 0 pause output

 
   
 
    
   
 
    
     0 output buffer failures, 0 output buffers swapped out

 
   
 
     
    
    
   
 show controllers 
 
    
   
 The show controllers command shows the type of SFP module installed in the Gigabit Ethernet line card. 
 
    
   
 
    
Router# show controllers gigabitethernet 4/0/0

 
   
 
    
   
 
    
Interface GigabitEthernet4/0/0(idb 0x70CAE948)

 
   
 
    
   
 
    
Hardware is Half-height Gigabit Ethernet MAC Controller, network connection mode is auto

 
   
 
    
   
 
    
  network link is up

 
   
 
    
   
 
    
  loopback type is none

 
   
 
    
   
 
    
  SFP type is 1000BASE-SX

 
   
 
    
   
 
    
  ip_routecache=0x11(dfs=0/mdfs=0), max_mtu=1524

 
   
 
    
   
 
    
  c10k_ge1h_ds=0x63E34E4C

 
   
 
    
   
 
    
  resets=3, reset_init=1, reset_restart=3

 
   
 
    
   
 
    
  link_state_reason=7

 
   
 
     
    
    
   
 show running config 
 
    
   
 The show running config command shows which line cards are installed in which slots. Half-height line cards are installed in slot 3 (0, 1) and slot 4 (0, 1). 
 
    
   
 
    
Router# show running-config 

 
   
 
    
   
 
    
 
   
 
    
   
 
    
card 1/1 2cable-tccplus

 
   
 
    
   
 
    
card 2/0 1gigethernet-1

 
   
 
    
   
 
    
card 2/1 2cable-tccplus

 
   
 
    
   
 
    
card 3/0 1gigethernet-hh-1

 
   
 
    
   
 
    
card 4/0 1gigethernet-hh-1

 
   
 
    
   
 
    
card 4/1 1gigethernet-hh-1

 
   
 
    
   
 
    
card 5/0 5cable-mc520u-d

 
   
 
    
   
 
    
 
   
 
     
    
    
   
 Upgrading to a Half-Height Gigabit Ethernet Line Card 
 
    
   
 This section provides instructions for upgrading from two full height gigabit Ethernet line cards to half-height Gigabit Ethernet line cards. 
 
   
 
    
    
   
 Step 1 Verify traffic is passing through slot 3/0 and slot 4/0. 
 
    
    
   
 Step 2 Administratively shut down the line card in slot 3/0 and let traffic reroute through slot 4/0. 
 
    
   
 Step 3 Remove the full-height line card in slot 3/0. 
 
    
   
 Step 4 Install the slot splitter into slot 3/0. 
 
    
    
   
 Step 5 Install the HHGE line card in slot splitter 3/0/0. 
 
    
    
   
 Step 6 Configure and bring up the HHGE line card in slot 3/0/0. 
 
    
    
   
 Step 7 Repeat Step 2, Step 5, and Step 6 for the HHGE line card in slot 3/1/0 
 
    
   
 Step 8 Repeat Step 1 through Step 7 for the full-height line card in slot 4/0. 
 
   
 
    
     
    
    
   
 Additional References 
 
     
    
   
 Related Documents
 
   
 
    
 
      
      
      
 
        
        

          Document Name 
        
 		 
        
        

          Document Link 
        
 		 
      
 
      
 
       
 Cisco UBR10012 Universal Broadband Router Release Notes 
 		 
       
 http://www.cisco.com/en/US/products/hw/cable/ps2209/prod_release_notes_list.html 
 		 
      
 
      
 
       
 Cisco uBR10012 Universal Broadband Router Software Configuration Guide 
 		 
       
 http://www.cisco.com/en/US/docs/cable/cmts/ubr10012/configuration/guide/scg.html 
 		 
      
 
      
 
       
 Cisco uBR10012 Universal Broadband Router Hardware Installation Guide 
 		 
       
 http://www.cisco.com/en/US/docs/cable/cmts/ubr10012/installation/guide/hig.html 
 		 
      
 
      
 
       
 Regulatory Compliance and Safety Information for the Cisco uBR10012 Universal Broadband Router  
 		 
       
 http://www.cisco.com/en/US/docs/cable/cmts/ubr10012/regulatory/compliance/ub10rcsi.html 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
     
    
    
   
 Standards
 
   
 
    
 
      
      
      
 
        
        

          Standard 
        
 		 
        
        

          Title 
        
 		 
      
 
      
 
       
 DOCSIS 1.0 
 		 
       
 Data Over Cable Service Interface Specification 1.0 
 		 
      
 
      
 
       
 DOCSIS 1.1 
 		 
       
 Data Over Cable Service Interface Specification 1.1 
 		 
      
 
      
 
       
 DOCSIS 2.0 
 		 
       
 Data Over Cable Service Interface Specification 2.0 
 		 
      
 
      
 
       
 IEEE 802.1q 
 		 
       
 VLAN frame-tagging standard 
 		 
      
 
      
 
       
 IEEE 802.3x 
 		 
       
 Flow control standard 
 		 
      
 
      
 
       
 IEEE 802.3ab 
 		 
       
 1000BASE-T, or Gigabit CX standard (using UTP Cat-5 cabling) specification 
 		 
      
 
      
 
       
 IEEE 802.3z 
 		 
       
 Gigabit Ethernet specification 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
     
    
    
   
 MIBs
 
   
 
    
 
      
      
      
 
        
        

          MIB 
        
 		 
        
        

          MIBs Link 
        
 		 
      
 
      
 
       
 •Cisco IF-MIB 
 
 •Cisco Entity-MIB 
 
 •Cisco Ethernet Link-MIB 
 
 •Cisco GE-MIB 
 		 
       
 To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL: 
 
 http://www.cisco.com/go/mibs 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
     
    
    
   
 RFCs
 
   
 
    
 
      
      
      
 
        
        

          RFC 
        
 		 
        
        

          Title 
        
 		 
      
 
      
 
       
 RFC 1213 
 		 
       
 Management Information Base for Network Management of TCP/IP-based internets:MIB-II 
 		 
      
 
      
 
       
 RFC 1573 
 		 
       
 Evolution of the Interfaces Group of MIB-II 
 		 
      
 
      
 
       
 RFC 2863 
 		 
       
 The Interfaces Group MIB 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
     
    
    
   
 Command Reference 
 
    
   
 This feature uses no new or modified commands. 
 
     
    
    
   
 Obtaining Documentation and Submitting a Service Request 
 
    
   
 For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: 
 
    
   
 http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html 
 
    
   
 Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0. 
 
    
    
   
 This document is to be used in conjunction with the documents listed in the Additional References section. 
 
    
    
    
   
 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) 
 
    
    
    
   
 © 2005-2008 Cisco Systems, Inc. All rights reserved. 
 
    
  
 
  
  
 


    
    


















     

     
    
    








	




    


    

        





































    

    

        

    

    
    
     
			
            

























    
    
    
    









            

                

















  
  

  
    
    
    
    
  






            

        
            
            




















  
Was this Document Helpful?

  
    
    
  
  
    
      
      FeedbackFeedback
    
  







            

                

















  
    
  



            


            

                
















    
Contact Cisco

    







            


            
            































    
   
    





            

                























      

    
    	
This Document Applies to These Products