- Cisco Unified Border Element Enterprise Management
- Cisco UBE Out-of-dialog OPTIONS Ping for Specified SIP Servers or Endpoints
- Pulse Code Modulation (PCM) Audio Capture
- Stateful Switchover Between Redundancy Paired Intra or Inter-box Devices
- SIP-to-SIP Extended Feature Functionality for Session Border Controllers
- Clearable SIP-UA Statistics
- Additional References
- Glossary
- Finding Feature Information
- Prerequisites for Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
- Restrictions for Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
- Information About Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
- Feature Information for Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
Stateful switchover provides protection for network edge devices with dual Route Processors (RPs) that represent a single point of failure in the network design, and where an outage might result in loss of service for customers.
- Finding Feature Information
- Prerequisites for Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
- Restrictions for Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
- Information About Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
- Feature Information for Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Prerequisites for Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
Cisco Unified Border Element (Enterprise)
Cisco Unified Border Element
Restrictions for Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
Information About Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
In specific Cisco networking devices that support dual RPs, stateful switchover takes advantage of Route Processor redundancy to increase network availability. When two route processors (RPs) are installed, one RP acts as the active RP, and the other acts as a backup, or standby RP. Following an initial synchronization between the two processors if the active RP fails, or is manually taken down for maintenance or removed, the standby RP detects the failure and initiates a switchover. During a switchover, the standby RP assumes control of the router, connects with the network interfaces, and activates the local network management interface and system console. Stateful switchover dynamically maintains Route Processor state information between them.
The following conditions and restrictions apply to the current implementation of SSO:
- Calls that are handled by nondefault session application (TCL/VXML) will not be checkpointed prebridge.
- Calls that require a DSP to be inserted (for example: Transcoded Calls) will not be checkpointed.
- Flow-through calls whose state has not been accurately checkpointed will be cleared with media inactivity-based clean up. This condition could occur if active failure happens when:
For more information about the Stateful Switchover feature and for detailed procedures for enabling this feature, see the "Configuring Stateful Switchover" chapter of the Cisco IOS High Availability Configuration Guide, Release 12.2SR
Feature Information for Stateful Switchover Between Redundancy Paired Intra- or Inter-box Devices
| Feature Name |
Releases |
Feature Information |
|---|---|---|
| Stateful Switchover Between Redundancy Paired Intra or Inter-box Devices |
Cisco IOS XE Release 3.2S |
Provides protection for network edge devices with dual Route Processors (RPs) that represent a single point of failure in the network design, and where an outage might result in loss of service for customers. The following commands were introduced or modified: None. |
| Stateful Switchover Between Redundancy Paired Intra or Inter-box Devices |
Cisco IOS Release 15.2(3)T |
Provides protection for network edge devices with dual Route Processors (RPs) that represent a single point of failure in the network design, and where an outage might result in loss of service for customers. The following commands were introduced or modified: None. |
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
Feedback