Cisco ASR 1006 Router Description
The Cisco ASR 1006 Router supports full-width card modules. It is designed with a single midplane with connectors on one interface midplane. The Cisco ASR 1006 Router supports:
-
Three Cisco ASR 1000 Series SPA Interface Processors (SIPs)
-
Twelve SPA slots
-
Two embedded services processors (Cisco ASR1000-ESP10, Cisco ASR1000-ESP20, Cisco ASR1000-ESP40, or Cisco ASR1000-ESP100)
![]() Note |
Cisco ASR1000-ESP40 and Cisco ASR1000-ESP100 are supported on Cisco ASR 1006 Router only if Cisco ASR1000-RP2 is installed on the router. |
-
Two Cisco ASR 1000 Series Route Processors (Cisco ASR1000-RP1 or Cisco ASR1000-RP2
) -
Dual (redundant) AC and DC power supplies
This section contains the following topics:
Front View
The following image shows the Cisco ASR 1006 Router with modules and filler plates installed.
![](/c/dam/en/us/td/i/200001-300000/280001-290000/280001-281000/280032.eps/_jcr_content/renditions/280032.jpg)
1 |
Slot R0 with ASR 1000 Series RP |
5 |
ASR 1000 Series SIP slot 0 |
2 |
Slot R1 with ASR 1000 Series RP |
6 |
ASR 1000 Series SIP slot 1 |
3 |
Slot F0 with ASR 1000 Series ESP |
7 |
ASR 1000 Series SIP slot 2 |
4 |
Slot F1 with ASR 1000 Series ESP |
Rear View
The following image shows the rear of the Cisco ASR 1006 Router with the ASR1006-PWR-AC power supply installed.
![](/c/dam/en/us/td/i/200001-300000/280001-290000/280001-281000/280029.eps/_jcr_content/renditions/280029.jpg)
1 |
AC power supply fan |
5 |
AC power supply handle |
2 |
AC power supply DB-25 alarm connector—A female DB-25 sub connector which enables you to attach an external alarm monitoring facility to the router, thus supporting a telco-style of handling alarm conditions in the router. For a description of the DB-25 alarm connector, see the “How Cisco ASR1000-RP Alarm Monitoring Works” section on page 2-22 . |
6 |
AC power inlet |
3 |
Cable tie wrap tabs |
7 |
AC power supply Standby switch. A Standby switch is not considered a disconnect. |
4 |
AC power supply captive screws |
8 |
AC power supply LEDs |
Internal fans draw cooling air into the chassis and across internal components to maintain an acceptable operating temperature. (See Cisco ASR 1006 Router Rear View with the AC Power Supply (ASR1006-PWR-AC).) The fans are located at the rear of the chassis. A two-hole grounding lug is located on the side of the chassis. Two power supplies, either two AC power supplies or two DC power supplies, are accessed from the rear of the router.
![]() Note |
You have already unpacked your chassis and read all the site requirements for your new equipment. Proceed with the installation. |
![]() Note |
Do not combine AC and DC power supplies in the same chassis. |
![]() Warning |
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 |
![]() Warning |
Before you install, operate, or service the system, read the Regulatory Compliance and Safety Information for Cisco ASR 1000 Series Aggregation Services Routers publication. This document provides important safety information you should know before working with the system. Statement 200 |
![]() Note |
You have already unpacked your chassis and read all the site requirements for your new equipment. Proceed with the installation. |
Cisco ASR 1006 Router Slot Numbering
1 |
Slot RP0 with ASR 1000 Series RP1 |
5 |
ASR 1000 Series SIP slot 0 |
2 |
Slot RP1 with ASR 1000 Series RP1 |
6 |
ASR 1000 Series SIP slot 1 |
3 |
Slot FP0 with ASR 1000 Series ESP |
7 |
ASR 1000 Series SIP slot 2 |
4 |
Slot FP1 with ASR 1000 Series ESP |
— |
— |
The Cisco ASR 1006 Router contains three Cisco ASR 1000 Series SPA Interfaces (SIPs) that support four subslots for the installation of SPAs.
shows the Cisco ASR 1006 Router SPA subslot location.