Examples
This is the sample output for show l2vpn bridge-domain command with
VxLAN parameters configured:
RP/0/RSP0/CPU0:router# show l2vpn bridge-domain bd-name bg1_bd1 detail
Legend: pp = Partially Programmed.
Bridge group: bg1, bridge-domain: bg1_bd1, id: 0, state: up, ShgId: 0, MSTi: 0
Coupled state: disabled
MAC learning: enabled
MAC withdraw: enabled
MAC withdraw for Access PW: enabled
MAC withdraw sent on: bridge port up
MAC withdraw relaying (access to access): disabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: no
MAC port down flush: enabled
MAC Secure: disabled, Logging: disabled
Split Horizon Group: none
Dynamic ARP Inspection: disabled, Logging: disabled
IP Source Guard: disabled, Logging: disabled
DHCPv4 snooping: disabled
IGMP Snooping: enabled
IGMP Snooping profile: none
MLD Snooping profile: none
Storm Control: disabled
Bridge MTU: 1500
MIB cvplsConfigIndex: 1
Filter MAC addresses:
P2MP PW: disabled
Create time: 30/03/2015 22:25:38 (00:26:08 ago)
No status change since creation
ACs: 2 (2 up), VFIs: 1, PWs: 0 (0 up), PBBs: 0 (0 up)
List of ACs:
AC: BVI1, state is up
Type Routed-Interface
MTU 1514; XC ID 0x80000001; interworking none
BVI MAC address:
1000.4444.0001
AC: GigabitEthernet0/8/0/0.1, state is up
Type VLAN; Num Ranges: 1
Outer Tag: 1
VLAN ranges: [1001, 1001]
MTU 1508; XC ID 0x508000a; interworking none
MAC learning: enabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: no
MAC port down flush: enabled
MAC Secure: disabled, Logging: disabled
Split Horizon Group: none
Dynamic ARP Inspection: disabled, Logging: disabled
IP Source Guard: disabled, Logging: disabled
DHCPv4 snooping: disabled
IGMP Snooping: enabled
IGMP Snooping profile: none
MLD Snooping profile: none
Storm Control: bridge-domain policer
Static MAC addresses:
Storm control drop counters:
packets: broadcast 0, multicast 0, unknown unicast 0
bytes: broadcast 0, multicast 0, unknown unicast 0
Dynamic ARP inspection drop counters:
packets: 0, bytes: 0
IP source guard drop counters:
packets: 0, bytes: 0
List of VNIs:
VNI 1, state is up
XC ID 0x80000014
Encap type VXLAN
Overlay nve100, Source 10.0.0.1, Multicast Group 225.1.1.1, UDP Port 4789
Anycast VTEP 100.1.1.1, Anycast Multicast Group 224.10.10.1
MAC learning: enabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: no
MAC port down flush: enabled
MAC Secure: disabled, Logging: disabled
Split Horizon Group: none
Dynamic ARP Inspection: disabled, Logging: disabled
IP Source Guard: disabled, Logging: disabled
DHCPv4 snooping: disabled
IGMP Snooping: enabled
IGMP Snooping profile: none
MLD Snooping profile: none
Storm Control: bridge-domain policer
List of Access PWs:
List of VFIs:
VFI bg1_bd1_vfi (up)
VFI Statistics:
drops: illegal VLAN 0, illegal length 0
The following sample output shows information for the bridge
ports such as attachment circuits and pseudowires for the specific bridge
domains:
RP/0/RSP0/CPU0:router# #show l2vpn bridge-domain
Tue Feb 23 20:21:56.758 PST
Bridge group: 189, bridge-domain: 189, id: 0, state: up, ShgId: 0, MSTi: 0
Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
Filter MAC addresses: 0
ACs: 2 (2 up), VFIs: 0, PWs: 0 (0 up), PBBs: 0 (0 up)
List of ACs:
Gi0/1/0/3.189, state: up, Static MAC addresses: 0
Gi0/1/0/7.189, state: up, Static MAC addresses: 0
List of Access PWs:
List of VFIs:
Bridge group: 190, bridge-domain: 190, id: 1, state: up, ShgId: 0, MSTi: 0
Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
Filter MAC addresses: 0
ACs: 0 (0 up), VFIs: 1, PWs: 3 (3 up), PBBs: 0 (0 up)
List of ACs:
List of Access PWs:
List of VFIs:
VFI 190
Neighbor 10.19.19.19 pw-id 190, state: up, Static MAC addresses: 0
Bridge group: 210, bridge-domain: 210, id: 2, state: up, ShgId: 0, MSTi: 0
Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
Filter MAC addresses: 0
ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up), PBBs: 0 (0 up)
List of ACs:
Gi0/1/0/7.210, state: up, Static MAC addresses: 0
List of Access PWs:
List of VFIs:
VFI 210
Neighbor 10.19.19.19 pw-id 210, state: up, Static MAC addresses: 0
Bridge group: 211, bridge-domain: 211, id: 3, state: up, ShgId: 0, MSTi: 0
Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
Filter MAC addresses: 0
ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up), PBBs: 0 (0 up)
List of ACs:
Gi0/1/0/7.211, state: up, Static MAC addresses: 0
List of Access PWs:
List of VFIs:
VFI 211
Neighbor 10.19.19.19 pw-id 211, state: up, Static MAC addresses: 0
Bridge group: 215, bridge-domain: 215, id: 4, state: up, ShgId: 0, MSTi: 0
Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
Filter MAC addresses: 0
ACs: 2 (2 up), VFIs: 1, PWs: 1 (1 up), PBBs: 0 (0 up)
List of ACs:
Gi0/1/0/3.215, state: up, Static MAC addresses: 0
Gi0/1/0/7.215, state: up, Static MAC addresses: 0
List of Access PWs:
List of VFIs:
VFI 215
Neighbor 10.19.19.19 pw-id 215, state: up, Static MAC addresses: 0
Bridge group: 2130, bridge-domain: 2130, id: 5, state: up, ShgId: 0, MSTi: 0
Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
Filter MAC addresses: 0
ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up), PBBs: 0 (0 up)
List of ACs:
Gi0/1/0/7.2130, state: up, Static MAC addresses: 0
List of Access PWs:
List of VFIs:
VFI 2130
Neighbor 10.19.19.19 pw-id 2130, state: up, Static MAC addresses: 0
This table
describes the significant fields shown in the display.
Table 1. show l2vpn
bridge-domain Command Field Descriptions
Field
|
Description
|
Bridge
group
|
Name of
bridge domain group is displayed.
|
bridge-domain
|
Name of
bridge domain is displayed.
|
id
|
ID
assigned to this bridge domain is displayed.
|
state
|
Current
state of the bridge domain is displayed.
|
ShgId
|
ID for the
default Split Horizon Group assigned to all attachment circuits and access
pseudowires that are part of this bridge domain is displayed.
Note
|
Members
of the special Split Horizon Group ID 0 forwards to other members of the same
SPG.
|
|
The following example shows sample output for a bridge named
bd1:
RP/0/RSP0/CPU0:router# show l2vpn bridge-domain bd-name bd1
Bridge group: g1, bridge-domain: bd1, id: 0, state: up, ShgId: 0, MSTi: 0
Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
Filter MAC addresses: 0
ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
List of ACs:
Gi0/1/0/0, state: up, Static MAC addresses: 2, MSTi: 0 (unprotected)
List of Access PWs:
List of VFIs:
VFI 1
Neighbor 10.1.1.1 pw-id 1, state: up, Static MAC addresses: 0
The following sample output shows brief information about the
bridges:
RP/0/RSP0/CPU0:router# show l2vpn bridge-domain brief
Bridge Group/Bridge-Domain Name ID State Num ACs/up Num PWs/up
-------------------------------- ----- ---------- -------------- ------------
bg1/bd1 0 up 1/1 0/0
bg1/bd2 1 up 0/0 0/0
bg1/bd3 2 up 0/0 0/0
This table describes the significant fields shown in the
display.
Table 2. show l2vpn
bridge-domain brief Command Field Descriptions
Field
|
Description
|
Bridge
Group/Bridge-Domain Name
|
Bridge
domain group name followed by the bridge domain name are displayed.
|
ID
|
ID
assigned to this bridge domain is displayed.
|
State
|
Current
state of the bridge domain is displayed.
|
Num ACs/up
|
Total
number of attachment circuits that are up in this bridge domain is displayed.
|
Num PWs/up
|
Total
number of pseudowires that are up in this bridge domain is displayed. The count
includes both VFI pseudowires and access pseudowires.
|
The following sample output shows detailed information for
IOS-XR releases 5.3.1 and earlier releases.
RP/0/RSP0/CPU0:router# show l2vpn bridge-domain detail
Bridge group: 210, bridge-domain: 210, id: 2, state: up, ShgId: 0, MSTi: 0
MAC learning: enabled
MAC withdraw: disabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: no
Security: disabled
Split Horizon Group: none
DHCPv4 snooping: disabled
IGMP Snooping profile: none
Bridge MTU: 9000
Filter MAC addresses:
ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
List of ACs:
AC: GigabitEthernet0/1/0/7.210, state is up
Type VLAN; Num Ranges: 1
vlan ranges: [100, 100]
MTU 9008; XC ID 0x440007; interworking none; MSTi 0 (unprotected)
MAC learning: enabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: no
Security: disabled
Split Horizon Group: enabled
DHCPv4 snooping: disabled
IGMP Snooping profile: none
Storm Control: disabled
Static MAC addresses:
Statistics:
packet totals: receive 31645, send 6
byte totals: receive 2405020, send 456
Storm control drop counters:
packet totals: broadcast 0, multicast 0, unknown unicast 0
byte totals: broadcast 0, multicast 0, unknown unicast 0
List of Access PWs:
List of VFIs:
VFI 210
PW: neighbor 10.19.19.19, PW ID 210, state is up ( established )
PW class not set, XC ID 0xfffc0004
Encapsulation MPLS, protocol LDP
PW type Ethernet, control word disabled, interworking none
PW backup disable delay 0 sec
Sequencing not set
MPLS Local Remote
------------ ------------------------------ -------------------------
Label 16001 16
Group ID 0x2 0x0
Interface 210 unknown
MTU 9000 9000
Control word disabled disabled
PW type Ethernet Ethernet
VCCV CV type 0x2 0x2
(LSP ping verification) (LSP ping verification)
VCCV CC type 0x6 0x2
(router alert label) (router alert label) s
(TTL expiry)
------------ ------------------------------ -------------------------
Create time: 13/04/1900 14:36:13 (17:46:22 ago)
Last time status changed: 13/04/1900 15:37:03 (16:45:32 ago)
MAC withdraw message: send 0 receive 0
Static MAC addresses:
Statistics:
packet totals: receive 6, send 31655
byte totals: receive 432, send 2279160
IGMP Snooping profile: none
VFI Statistics:
drops: illegal VLAN 0, illegal length 0
The following sample output shows that when a bridge operates
in VPLS mode, the irrelevant information for MAC learning is suppressed:
RP/0/RSP0/CPU0:router# show l2vpn bridge-domain detail
Bridge group: g1, bridge-domain: bd1, id: 0, state: up, ShgId: 0, MSTi: 0
MAC learning: enabled
MAC withdraw: disabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: yes
Security: disabled
DHCPv4 snooping: disabled
MTU: 1500
Filter MAC addresses:
ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
List of ACs:
AC: GigabitEthernet0/1/0/0, state is up
Type Ethernet
MTU 1500; XC ID 0x2000001; interworking none; MSTi 0
MAC learning: enabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: yes
Security: disabled
DHCPv4 snooping: disabled
Static MAC addresses:
0000.0000.0000
0001.0002.0003
List of Access PWs:
List of VFIs:
VFI 1
PW: neighbor 10.0.0.1, PW ID 1, state is up ( established )
PW class mpls, XC ID 0xff000001
Encapsulation MPLS, protocol LDP
PW type Ethernet, control word disabled, interworking none
PW backup disable delay 0 sec
Sequencing not set
MPLS Local Remote
------------ ------------------------------ ----------
Label 16003 16003
Group ID 0x0 0x0
Interface 1 1
MTU 1500 1500
Control word disabled disabled
PW type Ethernet Ethernet
VCCV CV type 0x2 0x2
(LSP ping verification) (LSP ping verification)
VCCV CC type 0x2 0x2
(router alert label) (router alert label)
------------ ------------------------------ ----------
Create time: 12/03/2008 14:03:00 (17:17:30 ago)
Last time status changed: 13/03/2008 05:57:58 (01:22:31 ago)
MAC withdraw message: send 0 receive 0
Static MAC addresses:
VFI Statistics:
drops: illegal VLAN 0, illegal length 0
Bridge group: g2, bridge-domain: pbb-bd1, id: 1, state: up, ShgId: 0, MSTi: 0
Type: pbb-edge, I-SID: 1234
Core-bridge: pbb-bd2
MAC learning: enabled
MAC withdraw: disabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: yes
Security: disabled
DHCPv4 snooping: disabled
MTU: 1500
Filter MAC addresses:
ACs: 1 (1 up), VFIs: 0, PWs: 0 (0 up), PBBs: 1 (1 up)
List of PBBs:
PBB Edge, state is up
XC ID 0x2000001
MAC learning: enabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: yes
Split Horizon Group: none
DHCPv4 snooping: disabled
IGMP Snooping profile:
Storm Control: disabled
Unknown-unicast-bmac: 666.777.888
CMAC to BMAC Mapping Table:
CMAC | BMAC
-------------------------------------------------
222.333.444 | 777.888.999
333.444.555 | 888.999.111
Statistics:
packet totals: receive 3919680,send 9328
byte totals: receive 305735040,send 15022146
List of ACs:
AC: GigabitEthernet0/1/0/0, state is up
Type Ethernet
MTU 1500; XC ID 0x2000001; interworking none; MSTi 0
MAC learning: enabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: yes
Security: disabled
DHCPv4 snooping: disabled
Static MAC addresses:
0000.0000.0000
0001.0002.0003
Bridge group: g2, bridge-domain: pbb-bd2, id: 2, state: up, ShgId: 0, MSTi: 0
Type: pbb-core
Number of associated pbb-edge BDs: 1
MAC learning: enabled
MAC withdraw: disabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: yes
Security: disabled
DHCPv4 snooping: disabled
MTU: 1500
Filter MAC addresses:
ACs: 1 (1 up), VFIs: 0, PWs: 0 (0 up), PBBs: 1 (1 up)
List of PBBs:
PBB Core, state is up
Vlan-id: 1; XC ID 0x2000001
MAC learning: enabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 600, Action: none, Notification: syslog
MAC limit reached: no
Security: disabled
Split Horizon Group: none
DHCPv4 snooping: profile foo
IGMP Snooping profile:
Storm Control: disabled
List of ACs:
AC: GigabitEthernet0/1/0/0, state is up
Type Ethernet
MTU 1500; XC ID 0x2000001; interworking none; MSTi 0
MAC learning: enabled
Flooding:
Broadcast & Multicast: enabled
Unknown unicast: enabled
MAC aging time: 300 s, Type: inactivity
MAC limit: 4000, Action: none, Notification: syslog
MAC limit reached: yes
Security: disabled
DHCPv4 snooping: disabled
Static MAC addresses:
0000.0000.0000
0001.0002.0003
This table describes the significant fields shown in the
display.
Table 3. show l2vpn
bridge-domain detail Command Field Descriptions
Field
|
Description
|
Bridge
group
|
Name of
bridge domain group is displayed.
|
bridge-domain
|
Name of
bridge domain is displayed.
|
ID
|
ID
assigned to this bridge domain is displayed.
|
state
|
Current
state of the bridge domain is displayed.
|
ShgId
|
Split
horizon group ID. This field is not used.
|
MSTi
|
ID for the
Multiple Spanning Tree.
|
Split
Horizon Group
|
Shows
whether the AC is a member of the split horizon group for ACs. There is only
one split horizon group for ACs per bridge domain.
- Enabled—The port belongs to
the split horizon group for ACs.
- None—The port does not
belong to the split horizon group for ACs.
|
The following sample output shows filter information about the
bridge-domain group named g1:
RP/0/RSP0/CPU0:router# show l2vpn bridge-domain group g1
Bridge group: g1, bridge-domain: bd1, id: 0, state: up, ShgId: 0, MSTi: 0
Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
Filter MAC addresses: 0
ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
List of ACs:
Gi0/1/0/0, state: up, Static MAC addresses: 2, MSTi: 0 (unprotected)
List of Access PWs:
List of VFIs:
VFI 1
Neighbor 10.1.1.1 pw-id 1, state: up, Static MAC addresses: 0
The following sample output shows display the filter information
for the interface on the bridge domain for IOS-XR 5.3.1 and earlier releases:
RP/0/RSP0/CPU0:router# show l2vpn bridge-domain interface gigabitEthernet 0/1/0/0
Bridge group: g1, bridge-domain: bd1, id: 0, state: up, ShgId: 0, MSTi: 0
Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
Filter MAC addresses: 0
ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
List of ACs:
Gi0/1/0/0, state: up, Static MAC addresses: 2, MSTi: 0 (unprotected)
The following sample output shows that the bridge domain
contains the pseudowires to match the filter for the neighbor for IOS-XR 5.3.1
and earlier releases:
RP/0/RSP0/CPU0:router# show l2vpn bridge-domain neighbor 10.1.1.1
Bridge group: g1, bridge-domain: bd1, id: 0, state: up, ShgId: 0, MSTi: 0
Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
Filter MAC addresses: 0
ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
List of Access PWs:
List of VFIs:
VFI 1
Neighbor 10.1.1.1 pw-id 1, state: up, Static MAC addresses: 0
The following sample output shows the summary information for
the bridge domain:
RP/0/RSP0/CPU0:router# show l2vpn bridge-domain summary
Number of groups: 1, bridge-domains: 2, Up: 2, Shutdown: 0
Default: 0, pbb-edge: 1, pbb-core: 1
Number of ACs: 1 Up: 1, Down: 0
Number of PWs: 0 Up: 0, Down: 0
This table describes the significant fields shown in the
display.
Table 4. show l2vpn
bridge-domain summary Command Field Descriptions
Field
|
Description
|
Number of
groups
|
Number of
configured bridge domain groups is displayed.
|
bridge-domains
|
Number of
configured bridge domains is displayed.
|
Shutdown
|
Number of
bridge domains that are in Shutdown state is displayed.
|
Number of
ACs
|
Number of
attachment circuits that are in Up state and Down state are displayed.
|
Number of
PWs
|
Number of
pseudowires that are in Up state and Down state are displayed. This includes
the VFI pseudowire and the access pseudowire.
|