Contents

These release notes apply to the following software release of the Cisco Network Plug and Play Solution:

■General Availability Release 1.1

These release notes contain the following sections:

■Introduction

■Supported Platforms and Software Requirements

■Upgrade and Downgrade Support

■Limitations

■Sizing Guidelines

■Upgrading a Cisco Catalyst 3650 or 3850 Series Switch to Cisco IOS XE Denali 16.1.1 While Provisioning

■Caveats

■Related Documentation

■Obtaining Documentation and Submitting a Service Request

Introduction

The Cisco Network Plug and Play solution provides a simple, secure, unified, and integrated offering for enterprise network customers to ease new branch or campus device deployments or for provisioning updates to an existing network. The solution provides a unified approach to provision enterprise networks comprised of Cisco routers, switches, and wireless access point devices with a near zero touch deployment experience.

Supported Platforms and Software Requirements

The following tables list Cisco routers, switches, wireless access points, and software releases that support the Cisco Plug and Play IOS Agent and the Cisco Network Plug and Play Solution.

 

1.The non-VLAN 1 feature is not supported on release 15.2.4E. 2.Limited feature support: Trustpool support for devices with smaller NVRAM space is only by using the DHCP options T and Z.

Table 2 lists software releases that have limited feature support. For software releases not listed, all features are supported.

 

1. The following caveats apply: CSCuv42560, CSCuw63034, CSCuy16820, CSCuy33129. For details, see the section Release 1.1 Open Caveats.

2. The following caveat applies: CSCux54515.

3. The following caveat applies: CSCux52544.

 

 

Note: Only official software releases obtained from the Cisco.com software download website are supported for image deployment. Engineering builds are not supported.

Upgrade and Downgrade Support

Limitations

The bulk import function is similar to adding new provisioning rules that can set a device to the pending state. When you export the project and device database, the application displays the correct device state. If you then import the saved database, the devices must contact the APIC-EM controller again to return to the provisioned state because the bulk import feature restores only the device provisioning rules and does not restore the state of devices.

Sizing Guidelines

The Cisco Network Plug and Play application on APIC-EM can support the following:

■A maximum of 10000 devices pre-provisioned in the Cisco Network Plug and Play application for APIC-EM, of which a maximum of 4000 can be router and switch devices and the remainder can be wireless access point devices

■A maximum of 50 devices of all types simultaneously contacting the server and being provisioned

■A maximum of 200 unclaimed devices of all types in the Cisco Network Plug and Play application for APIC-EM

See the Release Notes for Cisco Application Policy Infrastructure Controller Enterprise Module for APIC-EM device support guidelines.

Upgrading a Cisco Catalyst 3650 or 3850 Series Switch to Cisco IOS XE Denali 16.1.1 While Provisioning

This section applies if you have a Cisco Catalyst 3650 or 3850 Series switch with a software release of Cisco IOS XE 3.6.3, 3.7.2, or earlier, it is in a factory default state (unprovisioned in the network), and at the same time as provisioning you want to upgrade it to Cisco IOS XE Denali 16.1.1E.

Such devices with older software releases fail the normal upgrade process to release 16.1.1E, however, you can use the Cisco Network Plug and Play application to do the upgrade while provisioning the device, by using the following steps:

Prerequisite: The Cisco network device to be provisioned is in a factory default state and can be auto-booted with the 16.1.1E image. If you are using a network device that was previously configured or is in an unknown state, see the reset details in the Solution Guide for Cisco Network Plug and Play.

1. Put the Cisco IOS XE Denali 16.1.1E image on a TFTP server that is accessible to the device you are upgrading.

2. Create a configuration file for the device and add the following lines to the end of the file, which will upgrade the software and reload the switch:

The tftp URL must include the IP address of the TFTP server ( ip-address), the directory in which the image resides ( dir), and image filename ( filename).

3. Upload the configuration file in the Cisco Network Plug and Play application, by using the Upload button in the Configurations tab.

4. Add the configuration file to the device information, either in the Projects tab (for a new device that you are preprovisioning) or in the Unplanned Devices tab (for an unclaimed device that is already installed but not yet provisioned).

5. If the device is unclaimed, click Claim to provision it, or if you are preprovisioning a device that is not yet installed, it is automatically provisioned when it is installed. Note that it takes about 25 minutes for the upgrade to complete and there is minimal console output from the device during the process.

6. Verify that device status is Provisioned in the Cisco Network Plug and Play GUI.

7. Verify that the device is successfully deployed by checking the log messages by clicking on the device serial number. Look for the message, “Device was successfully deployed!!”

8. Verify that the installed software release is Denali 16.1.1E by using the show version command on the device.

Caveats

■Release 1.1 Resolved Caveats

■Release 1.1 Open Caveats

Related Documentation

■ Solution Guide for Cisco Network Plug and Play —Solution Guide for the Cisco Network Plug and Play solution.

■ Configuration Guide for Cisco Network Plug and Play on Cisco APIC-EM —Describes how to use the Network Plug and Play application in the APIC-EM to configure Cisco network devices.

■ Cisco Open Plug-n-Play Agent Configuration Guide —Describes how to configure the Cisco Open Plug-n-Play Agent software application that runs on a Cisco IOS or IOS-XE device.

■ Mobile Application User Guide for Cisco Network Plug and Play —Describes how to use the Cisco Network Plug and Play mobile application.

■ Cisco Application Policy Infrastructure Controller Enterprise Module Deployment Guide —Describes how to deploy and troubleshoot the Cisco APIC-EM.

■ Cisco Application Policy Infrastructure Controller Enterprise Module Configuration Guide —Describes how to configure settings for the Cisco APIC-EM.

■ Release Notes for the Cisco Application Policy Infrastructure Controller Enterprise Module —Release Notes for the Cisco APIC-EM.

■ Cisco APIC-EM Quick Start Guide —Guide to getting started with the APIC-EM and including a list of related documentation (available in the APIC-EM GUI).

■ Open Source Used In Cisco APIC-EM —List of open source code used in the Cisco APIC-EM.

■ Open Source Used In Cisco IWAN App Release 1 —List of open source code used in the Cisco IWAN and Cisco Network Plug and Play applications for APIC-EM.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What’s New in Cisco Product Documentation.

To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the  What’s New in Cisco Product Documentation RSS feed. The RSS feeds are a free service.

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

All printed copies and duplicate soft copies are considered un-Controlled copies and the original on-line version should be referred to for latest version.

Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

© 2015-2016 Cisco Systems, Inc. All rights reserved.