-
The example
shows how to enable L2CP on a port:
Switch#ProvisionL2CPPortType ?
<cr>
Switch(ProvisionL2CPPortType)#?
ProvisionL2CPPortType sub-mode commands:
default Set a command to its defaults
exit Exit from ProvisionL2CPPortType sub configuration mode
getL2CPPortConfig Get current L2CP configuration request
no Negate a command or set its defaults
setL2CPPortConfig Configure L2CP forward on EVCs on this port
Switch(ProvisionL2CPPortType)#setL2CPPortConfig ?
commit commit setL2CPPortConfig
flush flush all setL2CPPortConfig commands from queue
l2cpPortConfiguration Configure L2CP forward on EVCs on this port
review review setL2CPPortConfig commands
Switch(ProvisionL2CPPortType)#setL2CPPortConfig l2
Switch(ProvisionL2CPPortType)#$pPortConfiguration ?
discard Discard L2CP frames
enabled L2CP configuration enabled/disabled on this port
forward Allow forwarding of L2CP frames
peer Redirect L2CP frames to local protocol entity
portNumber Port number to configure L2CP
Switch(ProvisionL2CPPortType)#$guration portNumber 3
Switch(ProvisionL2CPPortType)#$guration enabled enable
Switch(ProvisionL2CPPortType)#setL2CPPortConfig review
Commands in queue:
setL2CPPortConfig l2cpPortConfiguration portNumber 3
setL2CPPortConfig l2cpPortConfiguration enabled enable
Commands in queue:
setL2CPPortConfig l2cpPortConfiguration portNumber 3
setL2CPPortConfig l2cpPortConfiguration enabled enable
Switch(ProvisionL2CPPortType)#setL2CPPortConfig commit
SetL2CPPortConfig Commit Success!!!
When
SetL2CPPortConfig operation is executed on a NID from a
Cisco ME 1200 NID
, initially GetL2CPPortConfig fetches the
current configuration. This is followed by SetL2CPPortConfig to set the new
L2CP configuration. The following is a sample output on the NID.
#
Decoding of Request message was successful
Decoded record:
GetL2CPPortConfig_Output.l2cpPortConfiguration.enabled = true
GetL2CPPortConfig_Output.l2cpPortConfiguration.portNumber = 3
GetL2CPPortConfig_Output.l2cpPortConfiguration.discard.discardList = ''
GetL2CPPortConfig_Output.l2cpPortConfiguration.forward.forwardList = '16-31'
GetL2CPPortConfig_Output.l2cpPortConfiguration.peer.peerList = '0-15'
GetL2CPPortConfig_Output.xmlns:ns0 = "http://new.webservice.namespace"
GetL2CPPortConfig_Output.xmlns:http = "http://schemas.xmlsoap.org/wsdl/http/"
GetL2CPPortConfig_Output.xmlns:mime = "http://schemas.xmlsoap.org/wsdl/mime/"
GetL2CPPortConfig_Output.xmlns:soap = "http://schemas.xmlsoap.org/wsdl/soap/"
GetL2CPPortConfig_Output.xmlns:soapenc = "http://schemas.xmlsoap.org/soap/encoding/"
GetL2CPPortConfig_Output.xmlns:wsdl = "http://schemas.xmlsoap.org/wsdl/"
Decoding of Request message was successful
Decoded record:
SetL2CPPortConfig_Input.l2cpPortConfiguration.enabled = true
SetL2CPPortConfig_Input.l2cpPortConfiguration.portNumber = 3
SetL2CPPortConfig_Input.l2cpPortConfiguration.discard.discardList = ''
SetL2CPPortConfig_Input.l2cpPortConfiguration.forward.forwardList = '16-31'
SetL2CPPortConfig_Input.l2cpPortConfiguration.peer.peerList = '0-15'
Encoding of Response message was successful
Encoded record:
SetL2CPPortConfig_Output.l2cpPortConfigResponse = 0
SetL2CPPortConfig_Output.xmlns:ns0 = "http://new.webservice.namespace"
SetL2CPPortConfig_Output.xmlns:http = "http://schemas.xmlsoap.org/wsdl/http/"
SetL2CPPortConfig_Output.xmlns:mime = "http://schemas.xmlsoap.org/wsdl/mime/"
SetL2CPPortConfig_Output.xmlns:soap = "http://schemas.xmlsoap.org/wsdl/soap/"
SetL2CPPortConfig_Output.xmlns:soapenc = "http://schemas.xmlsoap.org/soap/encoding/"
SetL2CPPortConfig_Output.xmlns:wsdl = "http://schemas.xmlsoap.org/wsdl/"
-
The examples
shows how to enable L2CP Forward on a port.
Switch#ProvisionL2CPPortType ?
<cr>
Switch(ProvisionL2CPPortType)#?
ProvisionL2CPPortType sub-mode commands:
default Set a command to its defaults
exit Exit from ProvisionL2CPPortType sub configuration mode
getL2CPPortConfig Get current L2CP configuration request
no Negate a command or set its defaults
setL2CPPortConfig Configure L2CP forward on EVCs on this port
Switch(ProvisionL2CPPortType)#setL2CPPortConfig ?
commit commit setL2CPPortConfig
flush flush all setL2CPPortConfig commands from queue
l2cpPortConfiguration Configure L2CP forward on EVCs on this port
review review setL2CPPortConfig commands
Switch(ProvisionL2CPPortType)#setL2CPPortConfig l2
Switch(ProvisionL2CPPortType)#$pPortConfiguration ?
discard Discard L2CP frames
enabled L2CP configuration enabled/disabled on this port
forward Allow forwarding of L2CP frames
peer Redirect L2CP frames to local protocol entity
portNumber Port number to configure L2CP
Switch(ProvisionL2CPPortType)#$guration portNumber 3
Switch(ProvisionL2CPPortType)#$guration enabled enable
Switch(ProvisionL2CPPortType)#$guration forward for
Switch(ProvisionL2CPPortType)#$orward forwardList 1-14
Switch(ProvisionL2CPPortType)#
Switch(ProvisionL2CPPortType)#setL2CPPortConfig review
Commands in queue:
setL2CPPortConfig l2cpPortConfiguration forward forwardList 1-14
setL2CPPortConfig l2cpPortConfiguration portNumber 3
setL2CPPortConfig l2cpPortConfiguration enabled enable
Switch(ProvisionL2CPPortType)#setL2CPPortConfig commit
SetL2CPPortConfig Commit Success!!!
The following
is a sample output on the NID.
#
Decoding of Request message was successful
Decoded record:
GetL2CPPortConfig_Input.l2cpPort = 3
Encoding of Response message was successful
Encoded record:
GetL2CPPortConfig_Output.l2cpPortConfiguration.enabled = true
GetL2CPPortConfig_Output.l2cpPortConfiguration.portNumber = 3
GetL2CPPortConfig_Output.l2cpPortConfiguration.discard.discardList = ''
GetL2CPPortConfig_Output.l2cpPortConfiguration.forward.forwardList = '16-31'
GetL2CPPortConfig_Output.l2cpPortConfiguration.peer.peerList = '0-15'
GetL2CPPortConfig_Output.xmlns:ns0 = "http://new.webservice.namespace"
GetL2CPPortConfig_Output.xmlns:http = "http://schemas.xmlsoap.org/wsdl/http/"
GetL2CPPortConfig_Output.xmlns:mime = "http://schemas.xmlsoap.org/wsdl/mime/"
GetL2CPPortConfig_Output.xmlns:soap = "http://schemas.xmlsoap.org/wsdl/soap/"
GetL2CPPortConfig_Output.xmlns:soapenc = "http://schemas.xmlsoap.org/soap/encoding/"
GetL2CPPortConfig_Output.xmlns:wsdl = "http://schemas.xmlsoap.org/wsdl/"
Decoding of Request message was successful
Decoded record:
SetL2CPPortConfig_Input.l2cpPortConfiguration.enabled = true
SetL2CPPortConfig_Input.l2cpPortConfiguration.portNumber = 3
SetL2CPPortConfig_Input.l2cpPortConfiguration.discard.discardList = ''
SetL2CPPortConfig_Input.l2cpPortConfiguration.forward.forwardList = '1-14'
SetL2CPPortConfig_Input.l2cpPortConfiguration.peer.peerList = '0-15'
Encoding of Response message was successful
Encoded record:
SetL2CPPortConfig_Output.l2cpPortConfigResponse = 0
SetL2CPPortConfig_Output.xmlns:ns0 = "http://new.webservice.namespace"
SetL2CPPortConfig_Output.xmlns:http = "http://schemas.xmlsoap.org/wsdl/http/"
SetL2CPPortConfig_Output.xmlns:mime = "http://schemas.xmlsoap.org/wsdl/mime/"
SetL2CPPortConfig_Output.xmlns:soap = "http://schemas.xmlsoap.org/wsdl/soap/"
SetL2CPPortConfig_Output.xmlns:soapenc = "http://schemas.xmlsoap.org/soap/encoding/"
SetL2CPPortConfig_Output.xmlns:wsdl = "http://schemas.xmlsoap.org/wsdl/"
#show running-config interface GigabitEthernet 1/3
Building configuration...
interface GigabitEthernet 1/3
switchport hybrid allowed vlan 1
switchport hybrid acceptable-frame-type untagged
switchport hybrid ingress-filtering
switchport hybrid port-type unaware
switchport mode trunk
lldp med type end-point
qos dscp-remark rewrite
evc l2cp forward 1-14
-
The examples
shows how to enable L2CP Forward, Peer, Discard on a port.
Switch#ProvisionL2CPPortType ?
<cr>
Switch(ProvisionL2CPPortType)#?
ProvisionL2CPPortType sub-mode commands:
default Set a command to its defaults
exit Exit from ProvisionL2CPPortType sub configuration mode
getL2CPPortConfig Get current L2CP configuration request
no Negate a command or set its defaults
setL2CPPortConfig Configure L2CP forward on EVCs on this port
Switch(ProvisionL2CPPortType)#setL2CPPortConfig ?
commit commit setL2CPPortConfig
flush flush all setL2CPPortConfig commands from queue
l2cpPortConfiguration Configure L2CP forward on EVCs on this port
review review setL2CPPortConfig commands
Switch(ProvisionL2CPPortType)#setL2CPPortConfig l2
Switch(ProvisionL2CPPortType)#$pPortConfiguration ?
discard Discard L2CP frames
enabled L2CP configuration enabled/disabled on this port
forward Allow forwarding of L2CP frames
peer Redirect L2CP frames to local protocol entity
portNumber Port number to configure L2CP
Switch(ProvisionL2CPPortType)#$guration portNumber 3
Switch(ProvisionL2CPPortType)#$guration enabled enable
Switch(ProvisionL2CPPortType)#$guration forward for
Switch(ProvisionL2CPPortType)#$orward forwardList 1-14
Switch(ProvisionL2CPPortType)#$peer peerList 16-20
Switch(ProvisionL2CPPortType)#$guration discard di
Switch(ProvisionL2CPPortType)#$iscard discardList 19
Switch(ProvisionL2CPPortType)#setL2CPPortConfig review
Commands in queue:
setL2CPPortConfig l2cpPortConfiguration portNumber 3
setL2CPPortConfig l2cpPortConfiguration enabled enable
setL2CPPortConfig l2cpPortConfiguration peer peerList 16-20
setL2CPPortConfig l2cpPortConfiguration discard discardList 19
setL2CPPortConfig l2cpPortConfiguration forward forwardList 1-14
Switch(ProvisionL2CPPortType)#setL2CPPortConfig review
Commands in queue:
setL2CPPortConfig l2cpPortConfiguration portNumber 3
setL2CPPortConfig l2cpPortConfiguration enabled enable
setL2CPPortConfig l2cpPortConfiguration peer peerList 16-20
setL2CPPortConfig l2cpPortConfiguration discard discardList 19
setL2CPPortConfig l2cpPortConfiguration forward forwardList 1-14
Switch(ProvisionL2CPPortType)#setL2CPPortConfig commit
SetL2CPPortConfig Commit Success!!!
The following
is a sample output on the NID.
# Decoding of Request message was successful
Decoded record:
GetL2CPPortConfig_Input.l2cpPort = 3
Encoding of Response message was successful
Encoded record:
GetL2CPPortConfig_Output.l2cpPortConfiguration.enabled = true
GetL2CPPortConfig_Output.l2cpPortConfiguration.portNumber = 3
GetL2CPPortConfig_Output.l2cpPortConfiguration.discard.discardList = ''
GetL2CPPortConfig_Output.l2cpPortConfiguration.forward.forwardList = '1-14'
GetL2CPPortConfig_Output.l2cpPortConfiguration.peer.peerList = '0-15'
GetL2CPPortConfig_Output.xmlns:ns0 = "http://new.webservice.namespace"
GetL2CPPortConfig_Output.xmlns:http = "http://schemas.xmlsoap.org/wsdl/http/"
GetL2CPPortConfig_Output.xmlns:mime = "http://schemas.xmlsoap.org/wsdl/mime/"
GetL2CPPortConfig_Output.xmlns:soap = "http://schemas.xmlsoap.org/wsdl/soap/"
GetL2CPPortConfig_Output.xmlns:soapenc = "http://schemas.xmlsoap.org/soap/encoding/"
GetL2CPPortConfig_Output.xmlns:wsdl = "http://schemas.xmlsoap.org/wsdl/"
Decoding of Request message was successful
Decoded record:
SetL2CPPortConfig_Input.l2cpPortConfiguration.enabled = true
SetL2CPPortConfig_Input.l2cpPortConfiguration.portNumber = 3
SetL2CPPortConfig_Input.l2cpPortConfiguration.discard.discardList = '19'
SetL2CPPortConfig_Input.l2cpPortConfiguration.forward.forwardList = '1-14'
SetL2CPPortConfig_Input.l2cpPortConfiguration.peer.peerList = '16-20'
Encoding of Response message was successful
Encoded record:
SetL2CPPortConfig_Output.l2cpPortConfigResponse = 0
SetL2CPPortConfig_Output.xmlns:ns0 = "http://new.webservice.namespace"
SetL2CPPortConfig_Output.xmlns:http = "http://schemas.xmlsoap.org/wsdl/http/"
SetL2CPPortConfig_Output.xmlns:mime = "http://schemas.xmlsoap.org/wsdl/mime/"
SetL2CPPortConfig_Output.xmlns:soap = "http://schemas.xmlsoap.org/wsdl/soap/"
SetL2CPPortConfig_Output.xmlns:soapenc = "http://schemas.xmlsoap.org/soap/encoding/"
SetL2CPPortConfig_Output.xmlns:wsdl = "http://schemas.xmlsoap.org/wsdl/"
# show running-config interface GigabitEthernet 1/3
Building configuration...
interface GigabitEthernet 1/3
switchport hybrid allowed vlan 1
switchport hybrid acceptable-frame-type untagged
switchport hybrid ingress-filtering
switchport hybrid port-type unaware
switchport mode trunk
lldp med type end-point
qos dscp-remark rewrite
evc l2cp peer 16-18,20 forward 1-14 discard 19
!
end
-
The examples
shows how to disable or reset L2CP Discard on a port.
Switch#ProvisionL2CPPortType ?
<cr>
Switch(ProvisionL2CPPortType)#?
ProvisionL2CPPortType sub-mode commands:
default Set a command to its defaults
exit Exit from ProvisionL2CPPortType sub configuration mode
getL2CPPortConfig Get current L2CP configuration request
no Negate a command or set its defaults
setL2CPPortConfig Configure L2CP forward on EVCs on this port
Switch(ProvisionL2CPPortType)#setL2CPPortConfig ?
commit commit setL2CPPortConfig
flush flush all setL2CPPortConfig commands from queue
l2cpPortConfiguration Configure L2CP forward on EVCs on this port
review review setL2CPPortConfig commands
Switch(ProvisionL2CPPortType)#setL2CPPortConfig l2
Switch(ProvisionL2CPPortType)#$pPortConfiguration ?
discard Discard L2CP frames
enabled L2CP configuration enabled/disabled on this port
forward Allow forwarding of L2CP frames
peer Redirect L2CP frames to local protocol entity
portNumber Port number to configure L2CP
Switch(ProvisionL2CPPortType)#$guration portNumber 3
Switch(ProvisionL2CPPortType)#$guration enabled enable
Switch(ProvisionL2CPPortType)#$guration discard di
Switch(ProvisionL2CPPortType)#$iscard discardList no
Switch(ProvisionL2CPPortType)#setL2CPPortConfig review
Commands in queue:
setL2CPPortConfig l2cpPortConfiguration portNumber 3
setL2CPPortConfig l2cpPortConfiguration enabled enable
setL2CPPortConfig l2cpPortConfiguration peer peerList 16-20
setL2CPPortConfig l2cpPortConfiguration discard discardList 19
setL2CPPortConfig l2cpPortConfiguration forward forwardList 1-14
Switch(ProvisionL2CPPortType)#setL2CPPortConfig review
Commands in queue:
setL2CPPortConfig l2cpPortConfiguration portNumber 3
setL2CPPortConfig l2cpPortConfiguration enabled enable
setL2CPPortConfig l2cpPortConfiguration discard discardList no
Switch(ProvisionL2CPPortType)#setL2CPPortConfig commit
SetL2CPPortConfig Commit Success!!!
The following
is a sample output on the NID.
# Decoding of Request message was successful
Decoded record:
GetL2CPPortConfig_Input.l2cpPort = 3
Encoding of Response message was successful
Encoded record:
GetL2CPPortConfig_Output.l2cpPortConfiguration.enabled = true
GetL2CPPortConfig_Output.l2cpPortConfiguration.portNumber = 3
GetL2CPPortConfig_Output.l2cpPortConfiguration.discard.discardList = '19'
GetL2CPPortConfig_Output.l2cpPortConfiguration.forward.forwardList = '1-14'
GetL2CPPortConfig_Output.l2cpPortConfiguration.peer.peerList = '16-20'
GetL2CPPortConfig_Output.xmlns:ns0 = "http://new.webservice.namespace"
GetL2CPPortConfig_Output.xmlns:http = "http://schemas.xmlsoap.org/wsdl/http/"
GetL2CPPortConfig_Output.xmlns:mime = "http://schemas.xmlsoap.org/wsdl/mime/"
GetL2CPPortConfig_Output.xmlns:soap = "http://schemas.xmlsoap.org/wsdl/soap/"
GetL2CPPortConfig_Output.xmlns:soapenc = "http://schemas.xmlsoap.org/soap/encoding/"
GetL2CPPortConfig_Output.xmlns:wsdl = "http://schemas.xmlsoap.org/wsdl/"
Decoding of Request message was successful
Decoded record:
SetL2CPPortConfig_Input.l2cpPortConfiguration.enabled = true
SetL2CPPortConfig_Input.l2cpPortConfiguration.portNumber = 3
SetL2CPPortConfig_Input.l2cpPortConfiguration.discard.discardList = 'no'
SetL2CPPortConfig_Input.l2cpPortConfiguration.forward.forwardList = '1-14'
SetL2CPPortConfig_Input.l2cpPortConfiguration.peer.peerList = '16-20'
Encoding of Response message was successful
Encoded record:
SetL2CPPortConfig_Output.l2cpPortConfigResponse = 0
SetL2CPPortConfig_Output.xmlns:ns0 = "http://new.webservice.namespace"
SetL2CPPortConfig_Output.xmlns:http = "http://schemas.xmlsoap.org/wsdl/http/"
SetL2CPPortConfig_Output.xmlns:mime = "http://schemas.xmlsoap.org/wsdl/mime/"
SetL2CPPortConfig_Output.xmlns:soap = "http://schemas.xmlsoap.org/wsdl/soap/"
SetL2CPPortConfig_Output.xmlns:soapenc = "http://schemas.xmlsoap.org/soap/encoding/"
SetL2CPPortConfig_Output.xmlns:wsdl = "http://schemas.xmlsoap.org/wsdl/"
# show running-config interface GigabitEthernet 1/3
Building configuration...
interface GigabitEthernet 1/3
switchport hybrid allowed vlan 1
switchport hybrid acceptable-frame-type untagged
switchport hybrid ingress-filtering
switchport hybrid port-type unaware
switchport mode trunk
lldp med type end-point
qos dscp-remark rewrite
evc l2cp peer 16-20 forward 1-14
-
The examples
shows how to retrieve current configuration on a NID.
Switch(ProvisionL2CPPortType)#getL2CPPortConfig ?
commit commit getL2CPPortConfig
flush flush all getL2CPPortConfig commands from queue
l2cpPort Get current L2CP configuration request
review review getL2CPPortConfig commands
Switch(ProvisionL2CPPortType)#getL2CPPortConfig l2cpPort ?
<1-6> Get L2CP Port Configuration Request
Switch(ProvisionL2CPPortType)#$Config l2cpPort 3 ?
<cr>
Switch(ProvisionL2CPPortType)#getL2CPPortConfig review
Commands in queue:
getL2CPPortConfig l2cpPort 3
Switch(ProvisionL2CPPortType)#
Switch(ProvisionL2CPPortType)#getL2CPPortConfig commit
GetL2CPPortConfig_Output.l2cpPortConfiguration.enabled = true
GetL2CPPortConfig_Output.l2cpPortConfiguration.portNumber = 3
GetL2CPPortConfig_Output.l2cpPortConfiguration.discard.discardList = 'no'
GetL2CPPortConfig_Output.l2cpPortConfiguration.forward.forwardList = '1-14'
GetL2CPPortConfig_Output.l2cpPortConfiguration.peer.peerList = '16-20'
GetL2CPPortConfig Commit Success!!!
The following
is a sample output on the NID.
# Decoding of Request message was successful
Decoded record:
GetL2CPPortConfig_Input.l2cpPort = 3
Encoding of Response message was successful
Encoded record:
GetL2CPPortConfig_Output.l2cpPortConfiguration.enabled = true
GetL2CPPortConfig_Output.l2cpPortConfiguration.portNumber = 3
GetL2CPPortConfig_Output.l2cpPortConfiguration.discard.discardList = 'no'
GetL2CPPortConfig_Output.l2cpPortConfiguration.forward.forwardList = '1-14'
GetL2CPPortConfig_Output.l2cpPortConfiguration.peer.peerList = '16-20'
GetL2CPPortConfig_Output.xmlns:ns0 = "http://new.webservice.namespace"
GetL2CPPortConfig_Output.xmlns:http = "http://schemas.xmlsoap.org/wsdl/http/"
GetL2CPPortConfig_Output.xmlns:mime = "http://schemas.xmlsoap.org/wsdl/mime/"
GetL2CPPortConfig_Output.xmlns:soap = "http://schemas.xmlsoap.org/wsdl/soap/"
GetL2CPPortConfig_Output.xmlns:soapenc = "http://schemas.xmlsoap.org/soap/encoding/"
GetL2CPPortConfig_Output.xmlns:wsdl = "http://schemas.xmlsoap.org/wsdl/"
-
The examples
shows how to flush L2CP configuration on a port.
Switch#ProvisionL2CPPortType ?
<cr>
Switch(ProvisionL2CPPortType)#?
ProvisionL2CPPortType sub-mode commands:
default Set a command to its defaults
exit Exit from ProvisionL2CPPortType sub configuration mode
getL2CPPortConfig Get current L2CP configuration request
no Negate a command or set its defaults
setL2CPPortConfig Configure L2CP forward on EVCs on this port
Switch(ProvisionL2CPPortType)#setL2CPPortConfig ?
commit commit setL2CPPortConfig
flush flush all setL2CPPortConfig commands from queue
l2cpPortConfiguration Configure L2CP forward on EVCs on this port
review review setL2CPPortConfig commands
Switch(ProvisionL2CPPortType)#setL2CPPortConfig review
Commands in queue:
setL2CPPortConfig l2cpPortConfiguration portNumber 3
setL2CPPortConfig l2cpPortConfiguration enabled enable
setL2CPPortConfig l2cpPortConfiguration forward forwardList 1-14
setL2CPPortConfig l2cpPortConfiguration peer peerList 16-20
Switch(ProvisionL2CPPortType)#setL2CPPortConfig flush
Switch(ProvisionL2CPPortType)#setL2CPPortConfig review
No commands in queue
-
The examples
shows how to remove specific configuration CLI from a
Cisco ME 1200 NID
.
Switch#ProvisionL2CPPortType ?
<cr>
Switch(ProvisionL2CPPortType)#?
ProvisionL2CPPortType sub-mode commands:
default Set a command to its defaults
exit Exit from ProvisionL2CPPortType sub configuration mode
getL2CPPortConfig Get current L2CP configuration request
no Negate a command or set its defaults
setL2CPPortConfig Configure L2CP forward on EVCs on this port
Switch(ProvisionL2CPPortType)#setL2CPPortConfig ?
commit commit setL2CPPortConfig
flush flush all setL2CPPortConfig commands from queue
l2cpPortConfiguration Configure L2CP forward on EVCs on this port
review review setL2CPPortConfig commands
Switch(ProvisionL2CPPortType)#setL2CPPortConfig review
Commands in queue:
setL2CPPortConfig l2cpPortConfiguration portNumber 3
setL2CPPortConfig l2cpPortConfiguration enabled enable
setL2CPPortConfig l2cpPortConfiguration forward forwardList 1-14
setL2CPPortConfig l2cpPortConfiguration peer peerList 16-20
Switch(ProvisionL2CPPortType)#no setL2CPPortConfig l2cpPor$
Switch(ProvisionL2CPPortType)#$n forward forwardList 1-14
Switch(ProvisionL2CPPortType)#setL2CPPortConfig review
Commands in queue:
setL2CPPortConfig l2cpPortConfiguration portNumber 3
setL2CPPortConfig l2cpPortConfiguration enabled enable
setL2CPPortConfig l2cpPortConfiguration peer peerList 16-20
Switch(ProvisionL2CPPortType)#setL2CPPortConfig review
Commands in queue:
setL2CPPortConfig l2cpPortConfiguration portNumber 3
setL2CPPortConfig l2cpPortConfiguration enabled enable
setL2CPPortConfig l2cpPortConfiguration peer peerList 16-20
Switch(ProvisionL2CPPortType)#setL2CPPortConfig commit
SetL2CPPortConfig Commit Success!!!