Cisco ASA 5500 Series Configuration Guide using the CLI, 8.4 and 8.6

General Connection Profile Connection Parameters

General parameters are common to all VPN connections. The general parameters include the following:

• Connection profile name—You specify a connection-profile name when you add or edit a connection profile. The following considerations apply:

– For clients that use preshared keys to authenticate, the connection profile name is the same as the group name that a client passes to the ASA.

– Clients that use certificates to authenticate pass this name as part of the certificate, and the ASA extracts the name from the certificate.

• Connection type—Connection types include IKEv1 remote-access, IPsec Lan-to-LAN, and Anyconnect (SSL/IKEv2). A connection profile can have only one connection type.
• Authentication, Authorization, and Accounting servers—These parameters identify the server groups or lists that the ASA uses for the following purposes:

– Authenticating users

– Obtaining information about services users are authorized to access

– Storing accounting records

A server group can consist of one or more servers.

• Default group policy for the connection—A group policy is a set of user-oriented attributes. The default group policy is the group policy whose attributes the ASA uses as defaults when authenticating or authorizing a tunnel user.
• Client address assignment method—This method includes values for one or more DHCP servers or address pools that the ASA assigns to clients.
• Override account disabled—This parameter lets you override the “account-disabled” indicator received from a AAA server.
• Password management—This parameter lets you warn a user that the current password is due to expire in a specified number of days (the default is 14 days), then offer the user the opportunity to change the password.
• Strip group and strip realm—These parameters direct the way the ASA processes the usernames it receives. They apply only to usernames received in the form user@realm.

A realm is an administrative domain appended to a username with the @ delimiter (user@abc). If you strip the realm, the ASA uses the username and the group (if present) for authentication. If you strip the group, the ASA uses the username and the realm (if present) for authentication.

Enter the strip-realm command to remove the realm qualifier, and enter the strip-group command to remove the group qualilfier from the username during authentication. If you remove both qualifiers, authentication is based on the username alone. Otherwise, authentication is based on the full username@realm or username < delimiter > group string. You must specify strip-realm if your server is unable to parse delimiters.

In addition, for L2TP/IPsec clients only, when you specify the strip-group command the ASA selects the connection profile (tunnel group) for user connections by obtaining the group name from the username presented by the VPN client.

• Authorization required—This parameter lets you require authorization before a user can connect, or turn off that requirement.
• Authorization DN attributes—This parameter specifies which Distinguished Name attributes to use when performing authorization.

IPsec Tunnel-Group Connection Parameters

IPsec parameters include the following:

• A client authentication method: preshared keys, certificates, or both.

– For IKE connections based on preshared keys, this is the alphanumeric key itself (up to 128 characters long), associated with the connection policy.

– Peer-ID validation requirement—This parameter specifies whether to require validating the identity of the peer using the peer’s certificate.

– If you specify certificates or both for the authentication method, the end user must provide a valid certificate in order to authenticate.

• An extended hybrid authentication method: XAUTH and hybrid XAUTH.

You use isakmp ikev1-user-authentication command to implement hybrid XAUTH authentication when you need to use digital certificates for ASA authentication and a different, legacy method for remote VPN user authentication, such as RADIUS, TACACS+ or SecurID.

• ISAKMP (IKE) keepalive settings. This feature lets the ASA monitor the continued presence of a remote peer and report its own presence to that peer. If the peer becomes unresponsive, the ASA removes the connection. Enabling IKE keepalives prevents hung connections when the IKE peer loses connectivity.

There are various forms of IKE keepalives. For this feature to work, both the ASA and its remote peer must support a common form. This feature works with the following peers:

– Cisco AnyConnect VPN Client

– Cisco VPN Client (Release 3.0 and above)

– Cisco VPN 3000 Client (Release 2.x)

– Cisco VPN 3002 Hardware Client

– Cisco VPN 3000 Series Concentrators

– Cisco IOS software

– Cisco Secure PIX Firewall

Non-Cisco VPN clients do not support IKE keepalives.

If you are configuring a group of mixed peers, and some of those peers support IKE keepalives and others do not, enable IKE keepalives for the entire group. The feature does not affect the peers that do not support it.

If you disable IKE keepalives, connections with unresponsive peers remain active until they time out, so we recommend that you keep your idle timeout short. To change your idle timeout, see “Configuring Group Policies” section.

Note To reduce connectivity costs, disable IKE keepalives if this group includes any clients connecting via ISDN lines. ISDN connections normally disconnect if idle, but the IKE keepalive mechanism prevents connections from idling and therefore from disconnecting.

If you do disable IKE keepalives, the client disconnects only when either its IKE or IPsec keys expire. Failed traffic does not disconnect the tunnel with the Peer Timeout Profile values as it does when IKE keepalives are enabled.

Note If you have a LAN-to-LAN configuration using IKE main mode, make sure that the two peers have the same IKE keepalive configuration. Both peers must have IKE keepalives enabled or both peers must have it disabled.

• If you configure authentication using digital certificates, you can specify whether to send the entire certificate chain (which sends the peer the identity certificate and all issuing certificates) or just the issuing certificates (including the root certificate and any subordinate CA certificates).
• You can notify users who are using outdated versions of Windows client software that they need to update their client, and you can provide a mechanism for them to get the updated client version. For VPN 3002 hardware client users, you can trigger an automatic update. You can configure and change the client-update, either for all connection profiles or for particular connection profiles.
• If you configure authentication using digital certificates, you can specify the name of the trustpoint that identifies the certificate to send to the IKE peer.

Connection Profile Connection Parameters for SSL VPN Sessions

Table 67-1 provides a list of connection profile attributes that are specific to SSL VPN (AnyConnect client and clientless) connections. In addition to these attributes, you configure general connection profile attributes common to all VPN connections. For step-by-step information about configuring connection profiles, see Configuring Connection Profiles for Clientless SSL VPN Sessions.

Note In earlier releases, “connection profiles” were known as “tunnel groups.” You configure a connection profile with tunnel-group commands. This chapter often uses these terms interchangeably.

Maximum Connection Profiles

The maximum number of connection profiles (tunnel groups) that an ASA can support is a function of the maximum number of concurrent VPN sessions for the platform + 5. For example, an ASA5505 can support a maximum of 25 concurrent VPN sessions allowing for 30 tunnel groups (25+5). Attempting to add an additional tunnel group beyond the limit results in the following message: "ERROR: The limit of 30 configured tunnel groups has been reached"

Table Table 67-2 specifies the maximum VPN sessions and connection profiles for each ASA platform.

Default IPsec Remote Access Connection Profile Configuration

The contents of the default remote-access connection profile are as follows:

Configuring IPsec Tunnel-Group General Attributes

The general attributes are common across more than one tunnel-group type. IPsec remote access and clientless SSL VPN tunnels share most of the same general attributes. IPsec LAN-to-LAN tunnels use a subset. Refer to the command reference for complete descriptions of all commands. The following sections describe, in order, how to configure remote-access and LAN-to-LAN connection profiles.

Configuring Remote-Access Connection Profiles

Use an remote-access connection profile when setting up a connection between the following remote clients and a central-site ASA:

– Legacy Cisco VPN Client (connecting with IPsec/IKEv1)

– AnyConnect Secure Mobility Client (connecting with SSL or IPsec/IKEv2)

– Clientless SSL VPN (browser-based connecting with SSL)

– Cisco ASA5500 Easy VPN hardware client (connecting with IPsec/IKEv1)

– Cisco VPM 3002 hardware client (connecting with IPsec/IKEv1)

We also provide a default group policy named DfltGrpPolicy.

To configure an remote-access connection profile, first configure the tunnel-group general attributes, then the remote-access attributes. See the following sections:

• Specifying a Name and Type for the Remote Access Connection Profile.
• Configuring Remote-Access Connection Profile General Attributes.
• Configuring Double Authentication
• Configuring Remote-Access Connection Profile IPsec IKEv1 Attributes.
• Configuring IPsec Remote-Access Connection Profile PPP Attributes

Specifying a Name and Type for the Remote Access Connection Profile

Create the connection profile, specifying its name and type, by entering the tunnel-group command. For an remote-access tunnel, the type is remote-access:

For example, to create an remote-access connection profile named TunnelGroup1, enter the following command:

Configuring Remote-Access Connection Profile General Attributes

To configure or change the connection profile general attributes, specify the parameters in the following steps.

Step 1 To configure the general attributes, enter the tunnel-group general-attributes command, which enters tunnel-group general-attributes configuration mode. The prompt changes to indicate the change in mode.

Step 2 Specify the name of the authentication-server group, if any, to use. If you want to use the LOCAL database for authentication if the specified server group fails, append the keyword LOCAL :

The name of the authentication server group can be up to 16 characters long.

You can optionally configure interface-specific authentication by including the name of an interface after the group name. The interface name, which specifies where the tunnel terminates, must be enclosed in parentheses. The following command configures interface-specific authentication for the interface named test using the server named servergroup1 for authentication:

Step 3 Specify the name of the authorization-server group, if any, to use. When you configure this value, users must exist in the authorization database to connect:

The name of the authorization server group can be up to 16 characters long. For example, the following command specifies the use of the authorization-server group FinGroup:

Step 4 Specify the name of the accounting-server group, if any, to use:

The name of the accounting server group can be up to 16 characters long. For example, the following command specifies the use of the accounting-server group named comptroller:

Step 5 Specify the name of the default group policy:

The name of the group policy can be up to 64 characters long. The following example sets DfltGrpPolicy as the name of the default group policy:

Step 6 Specify the names or IP addresses of the DHCP server (up to 10 servers), and the names of the DHCP address pools (up to 6 pools). The defaults are no DHCP server and no address pool. The dhcp-server command will allow you to configure the security appliance to send additional options to the specified DHCP servers when it is trying to get IP addresses for VPN clients. See the dhcp-server command in the Cisco Security Appliance Command Reference guide for more information.

Note If you specify an interface name, you must enclosed it within parentheses.

You configure address pools with the ip local pool command in global configuration mode.

Step 7 Specify the name of the NAC authentication server group, if you are using Network Admission Control, to identify the group of authentication servers to be used for Network Admission Control posture validation. Configure at least one Access Control Server to support NAC. Use the aaa-server command to name the ACS group. Then use the nac-authentication-server-group command, using the same name for the server group.

The following example identifies acs-group1 as the authentication server group to be used for NAC posture validation:

The following example inherits the authentication server group from the default remote access group.

Note NAC requires a Cisco Trust Agent on the remote host.

Step 8 Specify whether to strip the group or the realm from the username before passing it on to the AAA server. The default is not to strip either the group name or the realm.

A realm is an administrative domain. If you strip the realm, the ASA uses the username and the group (if present) authentication. If you strip the group, the ASA uses the username and the realm (if present) for authentication.Enter the strip-realm command to remove the realm qualifier, and use the strip-group command to remove the group qualilfier from the username during authentication. If you remove both qualifiers, authentication is based on the username alone. Otherwise, authentication is based on the full username@realm or username < delimiter > group string. You must specify strip-realm if your server is unable to parse delimiters.

Step 9 Optionally, if your server is a RADIUS, RADIUS with NT, or LDAP server, you can enable password management.

Note If you are using an LDAP directory server for authentication, password management is supported with the Sun Microsystems JAVA System Directory Server (formerly named the Sun ONE Directory Server) and the Microsoft Active Directory.

Sun—The DN configured on the ASA to access a Sun directory server must be able to access the default password policy on that server. We recommend using the directory administrator, or a user with directory administrator privileges, as the DN. Alternatively, you can place an ACI on the default password policy.

Microsoft—You must configure LDAP over SSL to enable password management with Microsoft Active Directory.

See the “Configuring Authorization with LDAP for VPN” section on page 35-16 for more information.

This feature, which is disabled by default, warns a user when the current password is about to expire. The default is to begin warning the user 14 days before expiration:

If the server is an LDAP server, you can specify the number of days (0 through 180) before expiration to begin warning the user about the pending expiration:

Note The password-management command, entered in tunnel-group general-attributes configuration mode replaces the deprecated radius-with-expiry command that was formerly entered in tunnel-group ipsec-attributes mode.

When you configure the password-management command, the ASA notifies the remote user at login that the user’s current password is about to expire or has expired. The ASA then offers the user the opportunity to change the password. If the current password has not yet expired, the user can still log in using that password. The ASA ignores this command if RADIUS or LDAP authentication has not been configured.

Note that this does not change the number of days before the password expires, but rather, the number of days ahead of expiration that the ASA starts warning the user that the password is about to expire.

If you do specify the password-expire-in-days keyword, you must also specify the number of days.

Specifying this command with the number of days set to 0 disables this command. The ASA does not notify the user of the pending expiration, but the user can change the password after it expires.

See Configuring Microsoft Active Directory Settings for Password Management for more information.

Note The ASA, releases 7.1 and later, generally supports password management for the AnyConnect VPN Client, the Cisco IPsec VPN Client, the SSL VPN full-tunneling client, and Clientless connections when authenticating with LDAP or with any RADIUS connection that supports MS-CHAPv2. Password management is not supported for any of these connection types for Kerberos/AD (Windows password) or NT 4.0 Domain.

Some RADIUS servers that support MS-CHAP do not currently support MS-CHAPv2. The password-management command requires MS-CHAPv2, so please check with your vendor.

The RADIUS server (for example, Cisco ACS) could proxy the authentication request to another authentication server. However, from the ASA perspective, it is talking only to a RADIUS server.

For LDAP, the method to change a password is proprietary for the different LDAP servers on the market. Currently, the ASA implements the proprietary password management logic only for Microsoft Active Directory and Sun LDAP servers. Native LDAP requires an SSL connection. You must enable LDAP over SSL before attempting to do password management for LDAP. By default, LDAP uses port 636.

Step 10 Optionally, configure the ability to override an account-disabled indicator from a AAA server, by entering the override-account-disable command:

Note Allowing override-account-disable is a potential security risk.

Step 11 Specify the attribute or attributes to use in deriving a name for an authorization query from a certificate. This attribute specifies what part of the subject DN field to use as the username for authorization:

For example, the following command specifies the use of the CN attribute as the username for authorization:

The authorization-dn-attributes are C (Country), CN (Common Name), DNQ (DN qualifier), EA (E-mail Address), GENQ (Generational qualifier), GN (Given Name), I (Initials), L (Locality), N (Name), O (Organization), OU (Organizational Unit), SER (Serial Number), SN (Surname), SP (State/Province), T (Title), UID (User ID), and UPN (User Principal Name).

Step 12 Specify whether to require a successful authorization before allowing a user to connect. The default is not to require authorization.

Configuring Double Authentication

Double authentication is an optional feature that requires a user to enter an additional authentication credential, such as a second username and password, on the login screen. Specify the following commands to configure double authentication.

Step 1 Specify the secondary authentication server group. This command specifies the AAA server group to use as the secondary AAA server.

Note This command applies only to AnyConnect client VPN connections.

The secondary server group cannot specify an SDI server group. By default, no secondary authentication is required.

If you use the none keyword, no secondary authentication is required. The groupname value specifies the AAA server group name. Local specifies the use of the internal server database, and when used with the groupname value, LOCAL specifies fallback. For example, to set the primary authentication server group to sdi_group and the secondary authentication server group to ldap_server, enter the following commands:

Note If you specify the use-primary-name keyword, then the login dialog requests only one username. In addition, if the usernames are extracted from a digital certificate, only the primary username is used for authentication.

Step 2 If obtaining the secondary username from a certificate, specify the secondary-username-from-certificate command:

The values for the DN fields to extract from the certificate for use as a secondary username are the same as for the primary username-from-certificate command. Alternatively, you can specify the use-script keyword, which directs the ASA to use a script file generated by ASDM.

For example, to specify the Common Name as the primary username field and Organizational Unit as the secondary username field, enter the following commands:

Step 3 Specify the secondary-pre-fill-username command in tunnel-group webvpn-attributes mode to enable extracting a secondary username from a client certificate for use in authentication. Use the keywords to specify whether this command applies to a clientless connection or an SSL VPN (AnyConnect) client connection and whether you want to hide the extracted username from the end user. This feature is disabled by default. Clientless and SSL-client options can both exist at the same time, but you must configure them in separate commands.

For example, to specify the use of pre-fill-username for both the primary and secondary authentication for a connection, enter the following commands:

Step 4 Specify which authentication server to use to obtain the authorization attributes to apply to the connection. The primary authentication server is the default selection. This command is meaningful only for double authentication.

For example, to specify the use of the secondary authentication server, enter the following commands:

Step 5 Specify which authentication username, primary or secondary, to associate with the session. The default value is primary. With double authentication enabled, it is possible that two distinct usernames are authenticated for the session. The administrator must designate one of the authenticated usernames as the session username. The session username is the username provided for accounting, session database, syslogs, and debug output.

For example, to specify that the authentication username associated with the session must come from the secondary authentication server, enter the following commands:

Configuring Remote-Access Connection Profile IPsec IKEv1 Attributes

To configure the IPsec IKEv1 attributes for a remote-access connection profile, do the following steps. The following description assumes that you have already created the remote-access connection profile. Remote-access connection profiles have more attributes than LAN-to-LAN connection profiles:

Step 1 To specify the IPsec attributes of an remote-access tunnel-group, enter tunnel-group ipsec-attributes mode by entering the following command. The prompt changes to indicate the mode change:

This command enters tunnel-group ipsec-attributes configuration mode, in which you configure the remote-access tunnel-group IPsec attributes.

For example, the following command designates that the tunnel-group ipsec-attributes mode commands that follow pertain to the connection profile named TG1. Notice that the prompt changes to indicate that you are now in tunnel-group ipsec-attributes mode:

Step 2 Specify the preshared key to support IKEv1 connections based on preshared keys. For example, the following command specifies the preshared key xyzx to support IKEv1 connections for an IPsec IKEv1 remote access connection profile:

Step 3 Specify whether to validate the identity of the peer using the peer’s certificate:

The available options are req (required), cert ( if supported by certificate), and nocheck ( do not check). The default is req.

For example, the following command specifies that peer-id validation is required:

Step 4 Specify whether to enable sending of a certificate chain. The following command includes the root certificate and any subordinate CA certificates in the transmission:

This attribute applies to all IPsec tunnel-group types.

Step 5 Specify the name of a trustpoint that identifies the certificate to be sent to the IKE peer:

The following command specifies mytrustpoint as the name of the certificate to be sent to the IKE peer:

Step 6 Specify the ISAKMP keepalive threshold and the number of retries allowed.

The threshold parameter specifies the number of seconds (10 through 3600) that the peer is allowed to idle before beginning keepalive monitoring. The retry parameter is the interval (2 through 10 seconds) between retries after a keepalive response has not been received. IKE keepalives are enabled by default. To disable IKE keepalives, enter the no form of the isakmp command:

For example, the following command sets the IKE keepalive threshold value to 15 seconds and sets the retry interval to 10 seconds:

The default value for the threshold parameter is 300 for remote-access and 10 for LAN-to-LAN, and the default value for the retry parameter is 2.

To specify that the central site (“head end”) should never initiate ISAKMP monitoring, enter the following command:

Step 7 Specify the ISAKMP hybrid authentication method, XAUTH or hybrid XAUTH.

You use isakmp ikev1-user-authentication command to implement hybrid XAUTH authentication when you need to use digital certificates for ASA authentication and a different, legacy method for remote VPN user authentication, such as RADIUS, TACACS+ or SecurID. Hybrid XAUTH breaks phase 1 of IKE down into the following two steps, together called hybrid authentication:

a. The ASA authenticates to the remote VPN user with standard public key techniques. This establishes an IKE security association that is unidirectionally authenticated.

b. An XAUTH exchange then authenticates the remote VPN user. This extended authentication can use one of the supported legacy authentication methods.

Note Before the authentication type can be set to hybrid, you must configure the authentication server, create a preshared key, and configure a trustpoint.

You can use the isakmp ikev1-user-authentication command with the optional interface parameter to specify a particular interface. When you omit the interface parameter, the command applies to all the interfaces and serves as a back-up when the per-interface command is not specified. When there are two isakmp ikev1-user-authentication commands specified for a connection profile, and one uses the interface parameter and one does not, the one specifying the interface takes precedence for that particular interface.

For example, the following commands enable hybrid XAUTH on the inside interface for a connection profile called example-group:

Configuring IPsec Remote-Access Connection Profile PPP Attributes

To configure the Point-to-Point Protocol attributes for a remote-access connection profile, do the following steps. PPP attributes apply only to IPsec remote-access connection profiles. The following description assumes that you have already created the IPsec remote-access connection profile.

Step 1 Enter tunnel-group ppp-attributes configuration mode, in which you configure the remote-access tunnel-group PPP attributes, by entering the following command. The prompt changes to indicate the mode change:

For example, the following command designates that the tunnel-group ppp-attributes mode commands that follow pertain to the connection profile named TG1. Notice that the prompt changes to indicate that you are now in tunnel-group ppp-attributes mode:

Step 2 Specify whether to enable authentication using specific protocols for the PPP connection. The protocol value can be:

• pap—Enables the use of Password Authentication Protocol for the PPP connection.
• chap—Enables the use of Challenge Handshake Authentication Protocol for the PPP connection.
• ms-chap-v1 or ms-chap-v2—Enables the use of Microsoft Challenge Handshake Authentication Protocol, version 1 or version 2 for the PPP connection.
• eap—Enables the use of Extensible Authentication protocol for the PPP connection.

CHAP and MSCHAPv1 are enabled by default.

The syntax of this command is:

To disable authentication for a specific protocol, use the no form of the command:

For example, the following command enables the use of the PAP protocol for a PPP connection.

The following command enables the use of the MS-CHAP, version 2 protocol for a PPP connection:

The following command enables the use of the EAP-PROXY protocol for a PPP connection:

The following command disables the use of the MS-CHAP, version 1 protocol for a PPP connection:

Configuring LAN-to-LAN Connection Profiles

An IPsec LAN-to-LAN VPN connection profile applies only to LAN-to-LAN IPsec client connections. While many of the parameters that you configure are the same as for IPsec remote-access connection profiles, LAN-to-LAN tunnels have fewer parameters. The following sections show you how to configure a LAN-to-LAN connection profile:

• Specifying a Name and Type for a LAN-to-LAN Connection Profile
• Configuring LAN-to-LAN Connection Profile General Attributes
• Configuring LAN-to-LAN IPsec IKEv1 Attributes

Default LAN-to-LAN Connection Profile Configuration

The contents of the default LAN-to-LAN connection profile are as follows:

LAN-to-LAN connection profiles have fewer parameters than remote-access connection profiles, and most of these are the same for both groups. For your convenience in configuring the connection, they are listed separately here. Any parameters that you do not explicitly configure inherit their values from the default connection profile.

Specifying a Name and Type for a LAN-to-LAN Connection Profile

To specify a name and a type for a connection profile, enter the tunnel-group command, as follows:

For a LAN-to-LAN tunnel, the type is ipsec-l2l.; for example, to create the LAN-to-LAN connection profile named docs, enter the following command:

Configuring LAN-to-LAN Connection Profile General Attributes

To configure the connection profile general attributes, do the following steps:

Step 1 Enter tunnel-group general-attributes mode by specifying the general-attributes keyword:

The prompt changes to indicate that you are now in config-general mode, in which you configure the tunnel-group general attributes.

For example, for the connection profile named docs, enter the following command:

Step 2 Specify the name of the accounting-server group, if any, to use:

For example, the following command specifies the use of the accounting-server group acctgserv1:

Step 3 Specify the name of the default group policy:

For example, the following command specifies that the name of the default group policy is MyPolicy:

Configuring LAN-to-LAN IPsec IKEv1 Attributes

To configure the IPsec IKEv1 attributes, do the following steps:

Step 1 To configure the tunnel-group IPsec IKEv1 attributes, enter tunnel-group ipsec-attributes configuration mode by entering the tunnel-group command with the IPsec-attributes keyword.

For example, the following command enters config-ipsec mode so you can configure the parameters for the connection profile named TG1:

The prompt changes to indicate that you are now in tunnel-group ipsec-attributes configuration mode.

Step 2 Specify the preshared key to support IKEv1 connections based on preshared keys.

For example, the following command specifies the preshared key XYZX to support IKEv1 connections for an LAN-to-LAN connection profile:

Step 3 Specify whether to validate the identity of the peer using the peer’s certificate:

The available options are req (required), cert ( if supported by certificate), and nocheck ( do not check). The default is req. For example, the following command sets the peer-id-validate option to nocheck :

Step 4 Specify whether to enable sending of a certificate chain. This action includes the root certificate and any subordinate CA certificates in the transmission:

You can apply this attribute to all tunnel-group types.

Step 5 Specify the name of a trustpoint that identifies the certificate to be sent to the IKE peer:

For example, the following command sets the trustpoint name to mytrustpoint:

You can apply this attribute to all tunnel-group types.

Step 6 Specify the ISAKMP (IKE) keepalive threshold and the number of retries allowed. The threshold parameter specifies the number of seconds (10 through 3600) that the peer is allowed to idle before beginning keepalive monitoring. The retry parameter is the interval (2 through 10 seconds) between retries after a keepalive response has not been received. IKE keepalives are enabled by default. To disable ISAKMP keepalives, enter isakmp keepalive disable.

For example, the following command sets the ISAKMP keepalive threshold to 15 seconds and sets the retry interval to 10 seconds:

The default value for the threshold parameter for LAN-to-LAN is 10, and the default value for the retry parameter is 2.

To specify that the central site (“head end”) should never initiate ISAKMP monitoring, enter the following command:

Step 7 Specify the ISAKMP hybrid authentication method, XAUTH or hybrid XAUTH.

You use isakmp ikev1-user-authentication command to implement hybrid XAUTH authentication when you need to use digital certificates for ASA authentication and a different, legacy method for remote VPN user authentication, such as RADIUS, TACACS+ or SecurID. Hybrid XAUTH breaks phase 1 of IKE down into the following two steps, together called hybrid authentication:

a. The ASA authenticates to the remote VPN user with standard public key techniques. This establishes an IKE security association that is unidirectionally authenticated.

b. An XAUTH exchange then authenticates the remote VPN user. This extended authentication can use one of the supported legacy authentication methods.

Note Before the authentication type can be set to hybrid, you must configure the authentication server, create a preshared key, and configure a trustpoint.

For example, the following commands enable hybrid XAUTH for a connection profile called example-group:

Configuring Connection Profiles for Clientless SSL VPN Sessions

The tunnel-group general attributes for clientless SSL VPN connection profiles are the same as those for IPsec remote-access connection profiles, except that the tunnel-group type is webvpn and the strip-group and strip-realm commands do not apply. You define the attribute specific to clientless SSL VPN separately. The following sections describe how to configure clientless SSL VPN connection profiles:

• Configuring General Tunnel-Group Attributes for Clientless SSL VPN Sessions
• Configuring Tunnel-Group Attributes for Clientless SSL VPN Sessions

Configuring General Tunnel-Group Attributes for Clientless SSL VPN Sessions

To configure or change the connection profile general attributes, specify the parameters in the following steps.

Step 1 To configure the general attributes, enter tunnel-group general-attributes command, which enters tunnel-group general-attributes configuration mode. Note that the prompt changes:

To configure the general attributes for TunnelGroup3, created in the previous section, enter the following command:

Step 2 Specify the name of the authentication-server group, if any, to use. If you want to use the LOCAL database for authentication if the specified server group fails, append the keyword LOCAL:

For example, to configure the authentication server group named test, and to provide fallback to the LOCAL server if the authentication server group fails, enter the following command:

The authentication-server-group name identifies a previously configured authentication server or group of servers. Use the aaa-server command to configure authentication servers. The maximum length of the group tag is 16 characters.

You can also configure interface-specific authentication by including the name of an interface in parentheses before the group name. The following interfaces are available by default:

• inside—Name of interface GigabitEthernet0/1
• outside— Name of interface GigabitEthernet0/0

Other interfaces you have configured (using the interface command) are also available. The following command configures interface-specific authentication for the interface named outside using the server servergroup1 for authentication:

Step 3 Optionally, specify the name of the authorization-server group, if any, to use. If you are not using authorization, go to Step 6. When you configure this value, users must exist in the authorization database to connect:

Use the aaa-server command to configure authorization servers. The maximum length of the group tag is 16 characters.

For example, the following command specifies the use of the authorization-server group FinGroup:

Step 4 Specify whether to require a successful authorization before allowing a user to connect. The default is not to require authorization.

Step 5 Specify the attribute or attributes to use in deriving a name for an authorization query from a certificate. This attribute specifies what part of the subject DN field to use as the username for authorization:

For example, the following command specifies the use of the CN attribute as the username for authorization:

The authorization-dn-attributes are C (Country), CN (Common Name), DNQ (DN qualifier), EA (E-mail Address), GENQ (Generational qualifier), GN (Given Name), I (Initials), L (Locality), N (Name), O (Organization), OU (Organizational Unit), SER (Serial Number), SN (Surname), SP (State/Province), T (Title), UID (User ID), and UPN (User Principal Name).

Step 6 Optionally, specify the name of the accounting-server group, if any, to use. If you are not using accounting, go to Step 7. Use the aaa-server command to configure accounting servers. The maximum length of the group tag is 16 characters.:

For example, the following command specifies the use of the accounting-server group comptroller:

Step 7 Optionally, specify the name of the default group policy. The default value is DfltGrpPolicy:

The following example sets MyDfltGrpPolicy as the name of the default group policy:

Step 8 Optionally, specify the name or IP address of the DHCP server (up to 10 servers), and the names of the DHCP address pools (up to 6 pools). Separate the list items with spaces. The defaults are no DHCP server and no address pool.

Note The interface name must be enclosed in parentheses.

You configure address pools with the ip local pool command in global configuration mode. See Chapter 68, “Configuring IP Addresses for VPNs” for information about configuring address pools.

Step 9 Optionally, if your server is a RADIUS, RADIUS with NT, or LDAP server, you can enable password management.

Note If you are using an LDAP directory server for authentication, password management is supported with the Sun Microsystems JAVA System Directory Server (formerly named the Sun ONE Directory Server) and the Microsoft Active Directory.

• Sun—The DN configured on the ASA to access a Sun directory server must be able to access the default password policy on that server. We recommend using the directory administrator, or a user with directory administrator privileges, as the DN. Alternatively, you can place an ACI on the default password policy.
• Microsoft—You must configure LDAP over SSL to enable password management with Microsoft Active Directory.

See the “Configuring Authorization with LDAP for VPN” section on page 35-16 for more information.

This feature, which is enabled by default, warns a user when the current password is about to expire. The default is to begin warning the user 14 days before expiration:

If the server is an LDAP server, you can specify the number of days (0 through 180) before expiration to begin warning the user about the pending expiration:

Note The password-management command, entered in tunnel-group general-attributes configuration mode replaces the deprecated radius-with-expiry command that was formerly entered in tunnel-group ipsec-attributes mode.

When you configure this command, the ASA notifies the remote user at login that the user’s current password is about to expire or has expired. The ASA then offers the user the opportunity to change the password. If the current password has not yet expired, the user can still log in using that password. The ASA ignores this command if RADIUS or LDAP authentication has not been configured.

Note that this does not change the number of days before the password expires, but rather, the number of days ahead of expiration that the ASA starts warning the user that the password is about to expire.

If you do specify the password-expire-in-days keyword, you must also specify the number of days.

See Configuring Microsoft Active Directory Settings for Password Management for more information.

Step 10 Specifying this command with the number of days set to 0 disables this command. The ASA does not notify the user of the pending expiration, but the user can change the password after it expires.Optionally, configure the ability to override an account-disabled indicator from the AAA server, by entering the override-account-disable command:

Note Allowing override account-disabled is a potential security risk.

Configuring Tunnel-Group Attributes for Clientless SSL VPN Sessions

To configure the parameters specific to a clientless SSL VPN connection profile, follow the steps in this section. Clientless SSL VPN was formerly known as WebVPN, and you configure these attributes in tunnel-group webvpn-attributes mode.

Step 1 To specify the attributes of a clientless SSL VPN tunnel-group, enter tunnel-group webvpn-attributes mode by entering the following command. The prompt changes to indicate the mode change:

For example, to specify the webvpn-attributes for the clientless SSL VPN tunnel-group named sales, enter the following command:

Step 2 To specify the authentication method to use: AAA, digital certificates, or both, enter the authentication command. You can specify either aaa or certificate or both, in any order.

For example, The following command allows both AAA and certificate authentication:

Applying Customization

Customizations determine the appearance of the windows that the user sees upon login. You configure the customization parameters as part of configuring clientless SSL VPN.

To apply a previously defined web-page customization to change the look-and-feel of the web page that the user sees at login, enter the customization command in username webvpn configuration mode:

For example, to use the customization named blueborder, enter the following command:

You configure the customization itself by entering the customization command in webvpn mode.

The following example shows a command sequence that first establishes a customization named “123” that defines a password prompt. The example then defines a clientless SSL VPN tunnel-group named “test” and uses the customization command to specify the use of the customization named “123”:

Step 3 The ASA queries NetBIOS name servers to map NetBIOS names to IP addresses. Clientless SSL VPN requires NetBIOS to access or share files on remote systems. Clientless SSL VPN uses NetBIOS and the CIFS protocol to access or share files on remote systems. When you attempt a file-sharing connection to a Windows computer by using its computer name, the file server you specify corresponds to a specific NetBIOS name that identifies a resource on the network.

To make the NBNS function operational, you must configure at least one NetBIOS server (host). You can configure up to three NBNS servers for redundancy. The ASA uses the first server on the list for NetBIOS/CIFS name resolution. If the query fails, it uses the next server.

To specify the name of the NBNS (NetBIOS Name Service) server to use for CIFS name resolution, use the nbns-server command. You can enter up to three server entries. The first server you configure is the primary server, and the others are backups, for redundancy. You can also specify whether this is a master browser (rather than just a WINS server), the timeout interval, and the number of retries. A WINS server or a master browser is typically on the same network as the ASA, or reachable from that network. You must specify the timeout interval before the number of retries:

For example, to configure the server named nbnsprimary as the primary server and the server 192.168.2.2 as the secondary server, each allowing three retries and having a 5-second timeout, enter the following command:

The timeout interval can range from 1 through 30 seconds (default 2), and the number of retries can be in the range 0 through 10 (default 2).

The nbns-server command in tunnel-group webvpn-attributes configuration mode replaces the deprecated nbns-server command in webvpn configuration mode.

Step 4 To specify alternative names for the group, use the group-alias command. Specifying the group alias creates one or more alternate names by which the user can refer to a tunnel-group. The group alias that you specify here appears in the drop-down list on the user’s login page. Each group can have multiple aliases or no alias, each specified in separate commands. This feature is useful when the same group is known by several common names, such as “Devtest” and “QA”.

For each group alias, enter a group-alias command. Each alias is enabled by default. You can optionally explicitly enable or disable each alias:

For example, to enable the aliases QA and Devtest for a tunnel-group named QA, enter the following commands:

Note The webvpn tunnel-group-list must be enabled for the (dropdown) group list to appear.

Step 5 To specify incoming URLs or IP addresses for the group, use the group-url command. Specifying a group URL or IP address eliminates the need for the user to select a group at login. When a user logs in, the ASA looks for the user’s incoming URL or address in the tunnel-group-policy table. If it finds the URL or address and if group-url is enabled in the connection profile, then the ASA automatically selects the associated connection profile and presents the user with only the username and password fields in the login window. This simplifies the user interface and has the added advantage of never exposing the list of groups to the user. The login window that the user sees uses the customizations configured for that connection profile.

If the URL or address is disabled and group-alias is configured, then the dropdown list of groups is also displayed, and the user must make a selection.

You can configure multiple URLs or addresses (or none) for a group. Each URL or address can be enabled or disabled individually. You must use a separate group-url command for each URL or address specified. You must specify the entire URL or address, including either the http or https protocol.

You cannot associate the same URL or address with multiple groups. The ASA verifies the uniqueness of the URL or address before accepting the URL or address for a connection profile.

For each group URL or address, enter a group-url command. You can optionally explicitly enable (the default) or disable each URL or alias:

For example, to enable the group URLs http://www.cisco.com and http://192.168.10.10 for the tunnel-group named RadiusServer, enter the following commands:

For a more extensive example, see Customizing Login Windows for Users of Clientless SSL VPN sessions.

Step 6 To exempt certain users from running Cisco Secure Desktop on a per connection profile basis if they enter one of the group-urls, enter the following command:

Note Entering this command prevents the detection of endpoint conditions for these sessions, so you may need to adjust the dynamic access policy (DAP) configuration.

Step 7 To specify the DNS server group to use for a connection profile for clientless SSL VPN sessions, use the dns-group command. The group you specify must be one you already configured in global configuration mode (using the dns server-group and name-server commands).

By default, the connection profile uses the DNS server group DefaultDNS. However, this group must be configured before the security appliance can resolve DNS requests.

The following example configures a new DNS server group named corp_dns and specifies that server group for the connection profile telecommuters:

Step 8 (Optional) To enable extracting a username from a client certificate for use in authentication and authorization, use the pre-fill-username command in tunnel-group webvpn-attributes mode. There is no default value.

The pre-fill-username command enables the use of a username extracted from the certificate field specified in the username-from-certificate command (in tunnel-group general-attributes mode) as the username for username/password authentication and authorization. To use this pre-fill username from certificate feature, you must configure both commands.

Note In Release 8.0.4, the username is not pre-filled; instead, any data sent in the username field is ignored.

The following example, entered in global configuration mode, creates an IPsec remote access tunnel group named remotegrp, enables getting the username from a certificate, and specifies that the name for an authentication or authorization query for an SSL VPN client must be derived from a digital certificate:

Step 9 (Optional) To specify whether to override the group policy or username attributes configuration for downloading an AnyConnect or SSL VPN client, use the override-svc-download command. This feature is disabled by default.

The security appliance allows clientless or AnyConnect client connections for remote users based on whether clientless and/or SSL VPN is enabled in the group policy or username attributes with the vpn-tunnel-protocol command. The anyconnect ask command further modifies the client user experience by prompting the user to download the client or return to the WebVPN home page.

However, you might want clientless users logging in under specific tunnel groups to not experience delays waiting for the download prompt to expire before being presented with the clientless SSL VPN home page. You can prevent delays for these users at the connection profile level with the override-svc-download command. This command causes users logging through a connection profile to be immediately presented with the clientless SSL VPN home page regardless of the vpn-tunnel-protocol or anyconnect ask command settings.

In the following example, the you enter tunnel-group webvpn attributes configuration mode for the connection profile engineering and enable the connection profile to override the group policy and username attribute settings for client download prompts:

Step 10 (Optional) To enable the display of a RADIUS reject message on the login screen when authentication is rejected, use the radius-eject-message command:

The following example enables the display of a RADIUS rejection message for the connection profile named engineering:

Customizing Login Windows for Users of Clientless SSL VPN sessions

You can set up different login windows for different groups by using a combination of customization profiles and connection profiles. For example, assuming that you had created a customization profile called salesgui, you can create a connection profile for clientless SSL VPN sessions called sales that uses that customization profile, as the following example shows:

Step 1 In webvpn mode, define a customization for clientless SSL VPN access, in this case named salesgui and change the default logo to mycompanylogo.gif. You must have previously loaded mycompanylogo.gif onto the flash memory of the ASA and saved the configuration. See “ Chapter 74, “Configuring Clientless SSL VPN” ” for details.

Step 2 In global configuration mode, set up a username and associate with it the customization for clientless SSL VPN that you’ve just defined:

Step 3 In global configuration mode, create a tunnel-group for clientless SSL VPN sessions named sales:

Step 4 Specify that you want to use the salesgui customization for this connection profile:

Step 5 Set the group URL to the address that the user enters into the browser to log in to the ASA; for example, if the ASA has the IP address 192.168.3.3, set the group URL to https://192.168.3.3:

If a port number is required for a successful login, include the port number, preceded by a colon. The ASA maps this URL to the sales connection profile and applies the salesgui customization profile to the login screen that the user sees upon logging in to https://192.168.3.3.

Configuring Microsoft Active Directory Settings for Password Management

Note If you are using an LDAP directory server for authentication, password management is supported with the Sun Microsystems JAVA System Directory Server (formerly named the Sun ONE Directory Server) and the Microsoft Active Directory.

• Sun—The DN configured on the ASA to access a Sun directory server must be able to access the default password policy on that server. We recommend using the directory administrator, or a user with directory administrator privileges, as the DN. Alternatively, you can place an ACI on the default password policy.
• Microsoft—You must configure LDAP over SSL to enable password management with Microsoft Active Directory.

See the “Configuring Authorization with LDAP for VPN” section on page 35-16 for more information.

To use password management with Microsoft Active Directory, you must set certain Active Directory parameters as well as configuring password management on the ASA. This section describes the Active Directory settings associated with various password management actions. These descriptions assume that you have also enabled password management on the ASA and configured the corresponding password management attributes. The specific steps in the following sections refer to Active Directory terminology under Windows 2000.

• Using Active Directory to Force the User to Change Password at Next Logon.
• Using Active Directory to Specify Maximum Password Age.
• Using Active Directory to Override an Account Disabled AAA Indicator
• Using Active Directory to Enforce Password Complexity.

The following sections assume that you are using an LDAP directory server for authentication.

Using Active Directory to Force the User to Change Password at Next Logon

To force a user to change the user password at the next logon, specify the password-management command in tunnel-group general-attributes configuration mode on the ASA and do the following steps under Active Directory:

Step 1 Select to Start > Programs > Administrative Tools > Active Directory Users and Computers (Figure 67-1).

Figure 67-1 Active Directory—Administrative Tools Menu

Step 2 Right-click Username > Properties > Account.

Step 3 Check the check box for User must change password at next logon (Figure 67-2).

Figure 67-2 Active Directory—User Must Change Password at Next Logon

The next time this user logs on, the ASA displays the following prompt: “New password required. Password change required. You must enter a new password with a minimum length n to continue.” You can set the minimum required password length, n, as part of the Active Directory configuration at Start > Programs > Administrative Tools > Domain Security Policy > Windows Settings > Security Settings > Account Policies > Password Policy. Select Minimum password length.

Using Active Directory to Specify Maximum Password Age

To enhance security, you can specify that passwords expire after a certain number of days. To specify a maximum password age for a user password, specify the password-management command in tunnel-group general-attributes configuration mode on the ASA and do the following steps under Active Directory:

Step 1 Select Start > Programs > Administrative Tools > Domain Security Policy > Windows Settings > Security Settings > Account Policies > Password Policy.

Step 2 Double-click Maximum password age. This opens the Security Policy Setting dialog box.

Step 3 Check the Define this policy setting check box and specify the maximum password age, in days, that you want to allow.

Figure 67-3 Active Directory—Maximum Password Age

Note The radius-with-expiry command, formerly configured as part of tunnel-group remote-access configuration to perform the password age function, is deprecated. The password-management command, entered in tunnel-group general-attributes mode, replaces it.

Using Active Directory to Override an Account Disabled AAA Indicator

To override an account-disabled indication from a AAA server, specify the override-account-disable command in tunnel-group general-attributes configuration mode on theASA and do the following steps under Active Directory:

Note Allowing override account-disabled is a potential security risk.

Step 1 Select Start > Programs > Administrative Tools > Active Directory Users and Computers.

Step 2 Right-click Username > Properties > Account and select Disable Account from the menu.

Figure 67-4 Active Directory—Override Account Disabled

The user should be able to log on successfully, even though a AAA server provides an account-disabled indicator.

Using Active Directory to Enforce Minimum Password Length

To enforce a minimum length for passwords, specify the password-management command in tunnel-group general-attributes configuration mode on the ASA and do the following steps under Active Directory:

Step 1 Select Start > Programs > Administrative Tools > Domain Security Policy.

Step 2 Select Windows Settings > Security Settings > Account Policies > Password Policy.

Step 3 Double-click Minimum Password Length. This opens the Security Policy Setting dialog box.

Step 4 Check the Define this policy setting check box and specify the minimum number of characters that the password must contain.

Figure 67-5 Active Directory—Minimum Password Length

Using Active Directory to Enforce Password Complexity

To enforce complex passwords—for example, to require that a password contain upper- and lowercase letters, numbers, and special characters—specify the password-management command in tunnel-group general-attributes configuration mode on the ASA and do the following steps under Active Directory:

Step 1 Select Start > Programs > Administrative Tools > Domain Security Policy. Select Windows Settings > Security Settings > Account Policies > Password Policy.

Step 2 Double-click Password must meet complexity requirements to open the Security Policy Setting dialog box.

Step 3 Check the Define this policy setting check box and select Enable.

Figure 67-6 Active Directory—Enforce Password Complexity

Enforcing password complexity takes effect only when the user changes passwords; for example, when you have configured Enforce password change at next login or Password expires in n days. At login, the user receives a prompt to enter a new password, and the system will accept only a complex password.

Configuring the Connection Profile for RADIUS/SDI Message Support for the AnyConnect Client

This section describes procedures to ensure that the AnyConnect VPN client using RSA SecureID Software tokens can properly respond to user prompts delivered to the client through a RADIUS server proxying to an SDI server(s). This section contains the following topics:

• AnyConnect Client and RADIUS/SDI Server Interaction
• Configuring the Security Appliance to Support RADIUS/SDI Messages

Note If you have configured the double-authentication feature, SDI authentication is supported only on the primary authentication server.

AnyConnect Client and RADIUS/SDI Server Interaction

When a remote user connects to the ASA with the AnyConnect VPN client and attempts to authenticate using an RSA SecurID token, the ASA communicates with the RADIUS server, which in turn, communicates with the SDI server about the authentication.

During authentication, the RADIUS server presents access challenge messages to the ASA. Within these challenge messages are reply messages containing text from the SDI server. The message text is different when the ASA is communicating directly with an SDI server than when communicating through the RADIUS proxy. Therefore, in order to appear as a native SDI server to the AnyConnect client, the ASA must interpret the messages from the RADIUS server.

Also, because the SDI messages are configurable on the SDI server, the message text on the ASA must match (in whole or in part) the message text on the SDI server. Otherwise, the prompts displayed to the remote client user may not be appropriate for the action required during authentication. The AnyConnect client may fail to respond and authentication may fail.

The following section describes how to configure the ASA to ensure successful authentication between the client and the SDI server:

Configuring the Security Appliance to Support RADIUS/SDI Messages

The following section describes the steps to configure the ASA to interpret SDI-specific RADIUS reply messages and prompt the AnyConnect user for the appropriate action:

Step 1 Configure a connection profile (tunnel group) to forward RADIUS reply messages in a manner that simulates direct communication with an SDI server using the proxy-auth sdi command from tunnel-group webvpn configuration mode. Users authenticating to the SDI server must connect over this connection profile.

For example:

Step 2 Configure the RADIUS reply message text on the ASA to match (in whole or in part) the message text sent by the RADIUS server with the proxy-auth_map sdi command from tunnel-group webvpn configuration mode.

The default message text used by the ASA is the default message text used by Cisco Secure Access Control Server (ACS). If you are using Cisco Secure ACS, and it is using the default message text, you do not need to configure the message text on the ASA. Otherwise, use the proxy-auth_map sdi command to ensure the message text matches.

Table 67-3 shows the message code, the default RADIUS reply message text, and the function of each message. Because the security appliance searches for strings in the order that they appear in the table, you must ensure that the string you use for the message text is not a subset of another string.

For example, “new PIN” is a subset of the default message text for both new-pin-sup and next-ccode-and-reauth. If you configure new-pin-sup as “new PIN”, when the security appliance receives “new PIN with the next card code” from the RADIUS server, it will match the text to the new-pin-sup code instead of the next-ccode-and-reauth code.

Table 67-3 SDI Op-codes, Default Message Text, and Message Function

The following example enters aaa-server-host mode and changes the text for the RADIUS reply message new-pin-sup :

Default Group Policy

The ASA supplies a default group policy. You can modify this default group policy, but you cannot delete it. A default group policy, named DfltGrpPolicy, always exists on the ASA, but this default group policy does not take effect unless you configure the ASA to use it. When you configure other group policies, any attribute that you do not explicitly specify takes its value from the default group policy. To view the default group policy, enter the following command:

To configure the default group policy, enter the following command:

Note The default group policy is always internal. Despite the fact that the command syntax is
hostname(config)# group-policy DfltGrpPolicy {internal | external}, you cannot change its type to external.

To change any of the attributes of the default group policy, use the group-policy attributes command to enter attributes mode, then specify the commands to change whatever attributes that you want to modify:

Note The attributes mode applies only to internal group policies.

The default group policy, DfltGrpPolicy, that the ASA provides is as follows:

You can modify the default group policy, and you can also create one or more group policies specific to your environment.

Configuring Group Policies

A group policy can apply to any kind of tunnel. In each case, if you do not explicitly define a parameter, the group takes the value from the default group policy. To configure a group policy, follow the steps in the subsequent sections.

Configuring an External Group Policy

External group policies take their attribute values from the external server that you specify. For an external group policy, you must identify the AAA server group that the ASA can query for attributes and specify the password to use when retrieving attributes from the external AAA server group. If you are using an external authentication server, and if your external group-policy attributes exist in the same RADIUS server as the users that you plan to authenticate, you have to make sure that there is no name duplication between them.

Note External group names on the ASA refer to user names on the RADIUS server. In other words, if you configure external group X on the ASA, the RADIUS server sees the query as an authentication request for user X. So external groups are really just user accounts on the RADIUS server that have special meaning to the ASA. If your external group attributes exist in the same RADIUS server as the users that you plan to authenticate, there must be no name duplication between them

The ASA supports user authorization on an external LDAP or RADIUS server. Before you configure the ASA to use an external server, you must configure the server with the correct ASA authorization attributes and, from a subset of these attributes, assign specific permissions to individual users. Follow the instructions in Appendix C, “Configuring an External Server for Authorization and Authentication” to configure your external server.

To configure an external group policy, do the following steps specify a name and type for the group policy, along with the server-group name and a password:

Note For an external group policy, RADIUS is the only supported AAA server type.

For example, the following command creates an external group policy named ExtGroup that gets its attributes from an external RADIUS server named ExtRAD and specifies that the password to use when retrieving the attributes is newpassword:

Note You can configure several vendor-specific attributes (VSAs), as described in Appendix C, “Configuring an External Server for Authorization and Authentication”. If a RADIUS server is configured to return the Class attribute (#25), the ASA uses that attribute to authenticate the Group Name. On the RADIUS server, the attribute must be formatted as: OU=groupname; where groupname is identical to the Group Name configured on the ASA—for example, OU=Finance.

Configuring an Internal Group Policy

To configure an internal group policy, specify a name and type for the group policy:

For example, the following command creates the internal group policy named GroupPolicy1:

The default type is internal.

You can initialize the attributes of an internal group policy to the values of a preexisting group policy by appending the keyword from and specifying the name of the existing policy:

Configuring Group Policy Attributes

For internal group policies, you can specify particular attribute values. To begin, enter group-policy attributes mode, by entering the group-policy attributes command in global configuration mode.

The prompt changes to indicate the mode change. The group-policy-attributes mode lets you configure attribute-value pairs for a specified group policy. In group-policy-attributes mode, explicitly configure the attribute-value pairs that you do not want to inherit from the default group. The commands to do this are described in the following sections.

Configuring WINS and DNS Servers

You can specify primary and secondary WINS servers and DNS servers. The default value in each case is none. To specify these servers, do the following steps:

Step 1 Specify the primary and secondary WINS servers:

The first IP address specified is that of the primary WINS server. The second (optional) IP address is that of the secondary WINS server. Specifying the none keyword instead of an IP address sets WINS servers to a null value, which allows no WINS servers and prevents inheriting a value from a default or specified group policy.

Every time that you enter the wins-server command, you overwrite the existing setting. For example, if you configure WINS server x.x.x.x and then configure WINS server y.y.y.y, the second command overwrites the first, and y.y.y.y becomes the sole WINS server. The same is true for multiple servers. To add a WINS server rather than overwrite previously configured servers, include the IP addresses of all WINS servers when you enter this command.

The following example shows how to configure WINS servers with the IP addresses 10.10.10.15 and 10.10.10.30 for the group policy named FirstGroup:

Step 2 Specify the primary and secondary DNS servers:

The first IP address specified is that of the primary DNS server. The second (optional) IP address is that of the secondary DNS server. Specifying the none keyword instead of an IP address sets DNS servers to a null value, which allows no DNS servers and prevents inheriting a value from a default or specified group policy.

Every time that you enter the dns-server command you overwrite the existing setting. For example, if you configure DNS server x.x.x.x and then configure DNS server y.y.y.y, the second command overwrites the first, and y.y.y.y becomes the sole DNS server. The same is true for multiple servers. To add a DNS server rather than overwrite previously configured servers, include the IP addresses of all DNS servers when you enter this command.

The following example shows how to configure DNS servers with the IP addresses 10.10.10.15, and 10.10.10.30 for the group policy named FirstGroup:

Step 3 Configure the DHCP network scope:

DHCP scope specifies the range of IP addresses (that is, a subnetwork) that the ASA DHCP server should use to assign addresses to users of this group policy.

The following example shows how to set an IP subnetwork of 10.10.85.0 (specifying the address range of 10.10.85.0 through 10.10.85.255) for the group policy named First Group:

Configuring VPN-Specific Attributes

Follow the steps in this section to set the VPN attribute values. The VPN attributes control the access hours, the number of simultaneous logins allowed, the timeouts, the egress VLAN or ACL to apply to VPN sessions, and the tunnel protocol:

Step 1 Set the VPN access hours. To do this, you associate a group policy with a configured time-range policy, using the vpn-access-hours command in group-policy configuration mode.

A group policy can inherit a time-range value from a default or specified group policy. To prevent this inheritance, enter the none keyword instead of the name of a time-range in this command. This keyword sets VPN access hours to a null value, which allows no time-range policy.

The time-range variable is the name of a set of access hours defined in global configuration mode using the time-range command. The following example shows how to associate the group policy named FirstGroup with a time-range policy called 824:

Step 2 Specify the number of simultaneous logins allowed for any user, using the vpn-simultaneous-logins command in group-policy configuration mode.

The default value is 3. The range is an integer in the range 0 through 2147483647. A group policy can inherit this value from another group policy. Enter 0 to disable login and prevent user access. The following example shows how to allow a maximum of 4 simultaneous logins for the group policy named FirstGroup:

Note While the maximum limit for the number of simultaneous logins is very large, allowing several simultaneous logins could compromise security and affect performance.

Stale AnyConnect, IPsec Client, or Clientless sessions (sessions that are terminated abnormally) might remain in the session database, even though a “new” session has been established with the same username.

If the value of vpn-simultaneous-logins is 1, and the same user logs in again after an abnormal termination, then the stale session is removed from the database and the new session is established. If, however, the existing session is still an active connection and the same user logs in again, perhaps from another PC, the first session is logged off and removed from the database, and the new session is established.

If the number of simultaneous logins is a value greater than 1, then, when you have reached that maximum number and try to log in again, the session with the longest idle time is logged off. If all current sessions have been idle an equally long time, then the oldest session is logged off. This action frees up a session and allows the new login.

Step 3 Configure the user timeout period by entering the vpn-idle-timeout command in group-policy configuration mode or in username configuration mode:

AnyConnect (SSL IPsec/IKEv2): Use the global WebVPN default-idle-timeout value (seconds) from the command: hostname(config-webvpn)# default-idle-timeout

The range for this value in the WebVPN default-idle-timeout command is 60-86400 seconds; the default Global WebVPN Idle timeout in seconds -- default is 1800 seconds (30 min).

Note A non-zero idle timeout value is required by ASA for all AnyConnect connections.

For a WebVPN user, the default-idle-timeout value is enforced only if vpn-idle-timeout none is set in the group policy/username attribute.

Site-to-Site (IKEv1, IKEv2) and IKEv1 remote-access: Disable timeout and allow for an unlimited idle period.The following example shows how to set a VPN idle timeout of 15 minutes for the group policy named FirstGroup:

Step 4 Configure the the time at which an idle-timeout alert message is displayed to the user using the vpn-idle-timeout alert-interval {minutes | none} command. This alert message tells users how many minutes left they have until their VPN session is disconnected due to inactivity.

The following example shows how to set vpn-idle-timeout alert-interval so that users will be notified 20 minutes before their VPN session is disconnected due to inactivity. You can specify a range of 1-30 minutes.

hostname(config-webvpn)# vpn-idle-timeout alert-interval 20

The none parameter of the command indicates that users will not receive an alert.

The no form of the command: no vpn-idle-timeout alert-interval

indicates that the VPN idle timeout alert-interval attribute will be inherited from the Default Group Policy.

Step 5 Configure a maximum amount of time for VPN connections, using the vpn-session-timeout command in group-policy configuration mode or in username configuration mode.

The minimum time is 1 minute, and the maximum time is 35791394 minutes. There is no default value. At the end of this period of time, the ASA terminates the connection.

A group policy can inherit this value from another group policy. To prevent inheriting a value, enter the none keyword instead of specifying a number of minutes with this command. Specifying the none keyword permits an unlimited session timeout period and sets session timeout with a null value, which disallows a session timeout.

The following example shows how to set a VPN session timeout of 180 minutes for the group policy named FirstGroup:

Step 6 Configure the the time at which a session-timeout alert message is displayed to the user using the vpn-session-timeout alert-interval {minutes | none} command. This alert message tells users how many minutes left they have until their VPN session is automatically disconnected.

The following example shows how to set the vpn-session-timeout alert-interval so that users will be notified 20 minutes before their VPN session is disconnected. You can specify a range of 1-30 minutes.

hostname(config-webvpn)# vpn-session-timeout alert-interval 20

The none parameter of the command indicates that users will not receive an alert.

The no form of the command: no vpn-session-timeout alert-interval

indicates that the VPN session timeout alert-interval attribute will be inherited from the Default Group Policy.

Step 7 Choose one of the following options to specify an egress VLAN (also called “VLAN mapping”) for remote access or specify an ACL to filter the traffic:

• Enter the following command in group-policy configuration mode to specify the egress VLAN for remote access VPN sessions assigned to this group policy or to a group policy that inherits this group policy:

hostname(config-group-policy)# [ no ] vlan { vlan_id | none }

no vlan removes the vlan_id from the group policy. The group policy inherits the vlan value from the default group policy.

vlan none removes the vlan_id from the group policy and disables VLAN mapping for this group policy. The group policy does not inherit the vlan value from the default group policy.

vlan_id in the command vlan vlan_id is the number of the VLAN, in decimal format, to assign to remote access VPN sessions that use this group policy. The VLAN must be configured on this ASA per the instructions in the “Configuring VLAN Subinterfaces and 802.1Q Trunking” section on page 6-30.

none disables the assignment of a VLAN to the remote access VPN sessions that match this group policy.

Note The egress VLAN feature works for HTTP connections, but not for FTP and CIFS.

• Specify the name of the ACL to apply to VPN session, using the vpn - filter command in group policy mode. (You can also configure this attribute in username mode, in which case the value configured under username supersedes the group-policy value.)

You configure ACLs to permit or deny various types of traffic for this group policy. You then enter the vpn-filter command to apply those ACLs.

To remove the ACL, including a null value created by entering the vpn - filter none command, enter the no form of this command. The no option allows inheritance of a value from another group policy.

A group policy can inherit this value from another group policy. To prevent inheriting a value, enter the none keyword instead of specifying an ACL name. The none keyword indicates that there is no access list and sets a null value, thereby disallowing an access list.

The following example shows how to set a filter that invokes an access list named acl_vpn for the group policy named FirstGroup:

A vpn-filter command is applied to post-decrypted traffic after it exits a tunnel and pre-encrypted traffic before it enters a tunnel. An ACL that is used for a vpn-filter should NOT also be used for an interface access-group. When a vpn-filter command is applied to a group policy that governs Remote Access VPN client connections, the ACL should be configured with the client assigned IP addresses in the src_ip position of the ACL and the local network in the dest_ip position of the ACL.

When a vpn-filter command is applied to a group-policy that governs a LAN to LAN VPN connection, the ACL should be configured with the remote network in the src_ip position of the ACL and the local network in the dest_ip position of the ACL.

Caution should be used when constructing the ACLs for use with the vpn-filter feature. The ACLs are constructed with the post-decrypted traffic in mind. However, ACLs are also applied to the traffic in the opposite direction. For this pre-encrypted traffic that is destined for the tunnel, the ACLs are constructed with the src_ip and dest_ip positions swapped.

In the following example, the vpn-filter is used with a Remote Access VPN client.
This example assumes that the client assigned IP address is 10.10.10.1/24 and the local network is 192.168.1.0/24.

The following ACE will allow the Remote Access VPN client to telnet to the local network:

The following ACE will allow the local network to telnet to the Remote Access client:

Note Note: The ACE access-list vpnfilt-ra permit 10.10.10.1 255.255.255.255 192.168.1.0 255.255.255.0 eq 23 will allow the local network to initiate a connection to the Remote Access client on any TCP port if it uses a source port of 23. The ACE access-list vpnfilt-ra permit 10.10.10.1 255.255.255.255 eq 23 192.168.1.0 255.255.255.0 will allow the Remote Access client to initiate a connection to the local network on any TCP port if it uses a source port of 23.

In the next example, the vpn-filter is used with a LAN to LAN VPN connection. This example assumes that the remote network is 10.0.0.0/24 and the local network is 192.168.1.0/24.
The following ACE will allow remote network to telnet to the local network:

The following ACE will allow the local network to telnet to the remote network:

Note Note: The ACE access-list vpnfilt-l2l permit 10.0.0.0 255.255.255.0 192.168.1.0 255.255.255.0 eq 23 will allow the local network to initiate a connection to the remote network on any TCP port if it uses a source port of 23. The ACE access-list vpnfilt-l2l permit 10.0.0.0 255.255.255.0 eq 23 192.168.1.0 255.255.255.0 will allow the remote network to initiate a connection to the local network on any TCP port if it uses a source port of 23.

Step 8 Specify the VPN tunnel type for this group policy.

vpn-tunnel-protocol { ikev1 | ikev2 | l2tp-ipsec | ssl-client | ssl-clientless}

The default is IPsec. To remove the attribute from the running configuration, enter the no form of this command.

The parameter values for this command follow:

• ikev1—Negotiates an IPsec IKEv1 tunnel between two peers (the Cisco VPN Client or another secure gateway). Creates security associations that govern authentication, encryption, encapsulation, and key management.
• ikev2—Negotiates an IPsec IKEv2 tunnel between two peers (the AnyConnect Secure Mobility Client or another secure gateway). Creates security associations that govern authentication, encryption, encapsulation, and key management.
• l2tp-ipsec —Negotiates an IPsec tunnel for an L2TP connection
• ssl-client—Negotiates an SSL tunnel using TLS or DTLS with the AnyConnect Secure Mobility Client.
• ssl-clientless —Provides VPN services to remote users via an HTTPS-enabled web browser, and does not require a client.

Enter this command to configure one or more tunneling modes. You must configure at least one tunneling mode for users to connect over a VPN tunnel.

The following example shows how to configure the IPsec IKEv1 tunneling mode for the group policy named FirstGroup:

Configuring Security Attributes

The attributes in this section specify certain security settings for the group:

Step 1 Specify whether to let users store their login passwords on the client system, using the password-storage command with the enable keyword in group-policy configuration mode. To disable password storage, use the password-storage command with the disable keyword.

For security reasons, password storage is disabled by default. Enable password storage only on systems that you know to be in secure sites.

To remove the password-storage attribute from the running configuration, enter the no form of this command:

Specifying the no form enables inheritance of a value for password-storage from another group policy.

This command does not apply to interactive hardware client authentication or individual user authentication for hardware clients.

The following example shows how to enable password storage for the group policy named FirstGroup:

Step 2 Specify whether to enable IP compression, which is disabled by default.

Note IP compression is not supported for IPsec IKEv2 connections.

To enable LZS IP compression, enter the ip-comp command with the enable keyword in group-policy configuration mode. To disable IP compression, enter the ip-comp command with the disable keyword.

To remove the ip-comp attribute from the running configuration, enter the no form of this command. This enables inheritance of a value from another group policy.

Enabling data compression might speed up data transmission rates for remote dial-in users connecting with modems.

Caution Data compression increases the memory requirement and CPU usage for each user session and consequently decreases the overall throughput of the ASA. For this reason, we recommend that you enable data compression only for remote users connecting with a modem. Design a group policy specific to modem users, and enable compression only for them.

---

Step 3 Specify whether to require that users reauthenticate on IKE re-key by using the re-xauth command with the enable keyword in group-policy configuration mode.

Note IKE re-key is not supported for IKEv2 connections.

If you enable reauthentication on IKE re-key, the ASA prompts the user to enter a username and password during initial Phase 1 IKE negotiation and also prompts for user authentication whenever an IKE re-key occurs. Reauthentication provides additional security.

If the configured re-key interval is very short, users might find the repeated authorization requests inconvenient. To avoid repeated authorization requests, disable reauthentication. To check the configured re-key interval, in monitoring mode, enter the show crypto ipsec sa command to view the security association lifetime in seconds and lifetime in kilobytes of data. To disable user reauthentication on IKE re-key, enter the disable keyword. Reauthentication on IKE re-key is disabled by default.

To enable inheritance of a value for reauthentication on IKE re-key from another group policy, remove the re-xauth attribute from the running configuration by entering the no form of this command.

Note Reauthentication fails if there is no user at the other end of the connection.

Step 4 Specify whether to restrict remote users to access only through the connection profile, using the group-lock command in group-policy configuration mode.

The tunnel-grp-name variable specifies the name of an existing connection profile that the ASA requires for the user to connect. Group-lock restricts users by checking if the group configured in the VPN client is the same as the connection profile to which the user is assigned. If it is not, the ASA prevents the user from connecting. If you do not configure group-lock, the ASA authenticates users without regard to the assigned group. Group locking is disabled by default.

To remove the group-lock attribute from the running configuration, enter the no form of this command. This option allows inheritance of a value from another group policy.

To disable group-lock, enter the group-lock command with the none keyword. The none keyword sets group-lock to a null value, thereby allowing no group-lock restriction. It also prevents inheriting a group-lock value from a default or specified group policy

Step 5 Specify whether to enable perfect forward secrecy. In IPsec negotiations, perfect forward secrecy ensures that each new cryptographic key is unrelated to any previous key. A group policy can inherit a value for perfect forward secrecy from another group policy. Perfect forward secrecy is disabled by default. To enable perfect forward secrecy, use the pfs command with the enable keyword in group-policy configuration mode.

To disable perfect forward secrecy, enter the pfs command with the disable keyword.

To remove the perfect forward secrecy attribute from the running configuration and prevent inheriting a value, enter the no form of this command.

Configuring the Banner Message

Specify the banner, or welcome message, if any, that you want to display. The default is no banner. The message that you specify is displayed on remote clients when they connect. To specify a banner, enter the banner command in group-policy configuration mode. The banner text can be up to 510 characters long. Enter the “\n” sequence to insert a carriage return.

Note A carriage-return/line-feed included in the banner counts as two characters.

To delete a banner, enter the no form of this command. Be aware that using the no version of the command deletes all banners for the group policy.

A group policy can inherit this value from another group policy. To prevent inheriting a value, enter the none keyword instead of specifying a value for the banner string, as follows:

The following example shows how to create a banner for the group policy named FirstGroup:

Configuring IPsec-UDP Attributes for IKEv1

IPsec over UDP, sometimes called IPsec through NAT, lets a Cisco VPN client or hardware client connect via UDP to a ASA that is running NAT. It is disabled by default. IPsec over UDP is proprietary; it applies only to remote-access connections, and it requires mode configuration. The ASA exchanges configuration parameters with the client while negotiating SAs. Using IPsec over UDP may slightly degrade system performance.

To enable IPsec over UDP, configure the ipsec-udp command with the enable keyword in group-policy configuration mode, as follows:

To use IPsec over UDP, you must also configure the ipsec-udp-port command, as described below.

To disable IPsec over UDP, enter the disable keyword. To remove the IPsec over UDP attribute from the running configuration, enter the no form of this command. This enables inheritance of a value for IPsec over UDP from another group policy.

The Cisco VPN client must also be configured to use IPsec over UDP (it is configured to use it by default). The VPN 3002 requires no configuration to use IPsec over UDP.

The following example shows how to set IPsec over UDP for the group policy named FirstGroup:

If you enabled IPsec over UDP, you must also configure the ipsec-udp-port command in group-policy configuration mode. This command sets a UDP port number for IPsec over UDP. In IPsec negotiations, the ASA listens on the configured port and forwards UDP traffic for that port even if other filter rules drop UDP traffic. The port numbers can range from 4001 through 49151. The default port value is 10000.

To disable the UDP port, enter the no form of this command. This enables inheritance of a value for the IPsec over UDP port from another group policy.

The following example shows how to set an IPsec UDP port to port 4025 for the group policy named FirstGroup:

Configuring Split-Tunneling Attributes

Split tunneling lets a remote-access client conditionally direct packets over a VPN tunnel in encrypted form or to a network interface in clear text form. With split tunneling enabled, packets not bound for destinations on the other side of the tunnel do not have to be encrypted, sent across the tunnel, decrypted, and then routed to a final destination. The split-tunnel-policy command applies this split tunneling policy to a specific network.

Note The ASA does not currently support split tunneling for IPv6 traffic. The ASA tunnels all IPv6 traffic through the VPN connection, even when the it has no IPv6 configuration.

Differences in Client Split Tunneling Behavior for Traffic within the Subnet

The AnyConnect client and the legacy Cisco VPN client (the IPsec/IKEv1 client) behave differently when passing traffic to sites within the same subnet as the IP address assigned by the ASA. With AnyConnect, the client passes traffic to all sites specified in the split tunneling policy you configured, and to all sites that fall within the same subnet as the IP address assigned by the ASA. For example, if the IP address assigned by the ASA is 10.1.1.1 with a mask of 255.0.0.0, the endpoint device passes all traffic destined to 10.0.0.0/8, regardless of the split tunneling policy.

By contrast, the legacy Cisco VPN client only passes traffic to addresses specified by the split-tunneling policy, regardless of the subnet assigned to the client.

Therefore, use a netmask for the assigned IP address that properly references the expected local subnet.

Setting the Split-Tunneling Policy

Set the rules for tunneling traffic by specifying the split-tunneling policy:

The default is to tunnel all traffic. To set a split tunneling policy, enter the split-tunnel-policy command in group-policy configuration mode. To remove the split-tunnel-policy attribute from the running configuration, enter the no form of this command. This enables inheritance of a value for split tunneling from another group policy.

The excludespecified keyword defines a list of networks to which traffic goes in the clear. This feature is useful for remote users who want to access devices on their local network, such as printers, while they are connected to the corporate network through a tunnel. This option applies only to the Cisco VPN client.

The tunnelall keyword specifies that no traffic goes in the clear or to any other destination than the ASA. This, in effect, disables split tunneling. Remote users reach Internet networks through the corporate network and do not have access to local networks. This is the default option.

The tunnelspecified keyword tunnels all traffic from or to the specified networks. This option enables split tunneling. It lets you create a network list of addresses to tunnel. Data to all other addresses travels in the clear and is routed by the remote user’s Internet service provider.

Note Split tunneling is primarily a traffic management feature, not a security feature. For optimum security, we recommend that you do not enable split tunneling.

The following example shows how to set a split tunneling policy of tunneling only specified networks for the group policy named FirstGroup:

Creating a Network List for Split-Tunneling

Create a network list for split tunneling using the split-tunnel-network-list command in group-policy configuration mode.

Split tunneling network lists distinguish networks that require traffic to travel across the tunnel from those that do not require tunneling. The ASA makes split tunneling decisions on the basis of a network list, which is an ACL that consists of a list of addresses on the private network.

If you use extended ACLs, the source network determines the split-tunneling network. The destination network is ignored. In addition, because any is not an actual IP address or network address, do not use the term for the source in the ACL.

The value access-list name parameter identifies an access list that enumerates the networks to tunnel or not tunnel.

The none keyword indicates that there is no network list for split tunneling; the ASA tunnels all traffic. Specifying the none keyword sets a split tunneling network list with a null value, thereby disallowing split tunneling. It also prevents inheriting a default split tunneling network list from a default or specified group policy.

To delete a network list, enter the no form of this command. To delete all split tunneling network lists, enter the no split-tunnel-network-list command without arguments. This command deletes all configured network lists, including a null list if you created one by entering the none keyword.

When there are no split tunneling network lists, users inherit any network lists that exist in the default or specified group policy. To prevent users from inheriting such network lists, enter the split-tunnel-network-list none command.

The following example shows how to set a network list called FirstList for the group policy named FirstGroup:

Configuring Domain Attributes for Tunneling

You can specify a default domain name for tunneled packets or a list of domains to be resolved through the split tunnel. The following sections describe how to set these domains.

Defining a Default Domain Name for Tunneled Packets

The ASA passes the default domain name to the IPsec client to append to DNS queries that omit the domain field. When there are no default domain names, users inherit the default domain name in the default group policy. To specify the default domain name for users of the group policy, enter the default-domain command in group-policy configuration mode. To delete a domain name, enter the no form of this command.

The value domain-name parameter identifies the default domain name for the group. To specify that there is no default domain name, enter the none keyword. This command sets a default domain name with a null value, which disallows a default domain name and prevents inheriting a default domain name from a default or specified group policy.

To delete all default domain names, enter the no default-domain command without arguments. This command deletes all configured default domain names, including a null list if you created one by entering the default-domain command with the none keyword. The no form allows inheriting a domain name.

The following example shows how to set a default domain name of FirstDomain for the group policy named FirstGroup:

Defining a List of Domains for Split Tunneling

Enter a list of domains to be resolved through the split tunnel. Enter the split-dns command in group-policy configuration mode. To delete a list, enter the no form of this command.

When there are no split tunneling domain lists, users inherit any that exist in the default group policy. To prevent users from inheriting such split tunneling domain lists, enter the split-dns command with the none keyword.

To delete all split tunneling domain lists, enter the no split-dns command without arguments. This deletes all configured split tunneling domain lists, including a null list created by issuing the split-dns command with the none keyword.

The parameter value domain-name provides a domain name that the ASA resolves through the split tunnel. The none keyword indicates that there is no split DNS list. It also sets a split DNS list with a null value, thereby disallowing a split DNS list, and prevents inheriting a split DNS list from a default or specified group policy. The syntax of the command is as follows:

Enter a single space to separate each entry in the list of domains. There is no limit on the number of entries, but the entire string can be no longer than 255 characters. You can use only alphanumeric characters, hyphens (-), and periods (.). If the default domain name is to be resolved through the tunnel, you must explicitly include that name in this list.

The following example shows how to configure the domains Domain1, Domain2, Domain3, and Domain4 to be resolved through split tunneling for the group policy named FirstGroup:

Configuring DHCP Intercept

A Microsoft XP anomaly results in the corruption of domain names if split tunnel options exceed 255 bytes. To avoid this problem, the ASA limits the number of routes it sends to 27 to 40 routes, with the number of routes dependent on the classes of the routes.

DHCP Intercept lets Microsoft Windows XP clients use split-tunneling with the ASA. The ASA replies directly to the Microsoft Windows XP client DHCP Inform message, providing that client with the subnet mask, domain name, and classless static routes for the tunnel IP address. For Windows clients prior to Windows XP, DHCP Intercept provides the domain name and subnet mask. This is useful in environments in which using a DHCP server is not advantageous.

The intercept-dhcp command enables or disables DHCP intercept. The syntax of this command is as follows:

[ no ] intercept-dhcp

The netmask variable provides the subnet mask for the tunnel IP address. The no version of the command removes the DHCP intercept from the configuration.

The following example shows how to set DHCP Intercepts for the group policy named FirstGroup:

Configuring Attributes for VPN Hardware Clients

The commands in this section enable or disable secure unit authentication and user authentication, and set a user authentication timeout value for VPN hardware clients. They also let you allow Cisco IP phones and LEAP packets to bypass individual user authentication and allow hardware clients using Network Extension Mode to connect.

Configuring Secure Unit Authentication

Secure unit authentication provides additional security by requiring VPN hardware clients to authenticate with a username and password each time that the client initiates a tunnel. With this feature enabled, the hardware client does not have a saved username and password. Secure unit authentication is disabled by default.

Note With this feature enabled, to bring up a VPN tunnel, a user must be present to enter the username and password.

Secure unit authentication requires that you have an authentication server group configured for the connection profile the hardware client(s) use. If you require secure unit authentication on the primary ASA, be sure to configure it on any backup servers as well.

Specify whether to enable secure unit authentication by entering the secure-unit-authentication command with the enable keyword in group-policy configuration mode.

To disable secure unit authentication, enter the disable keyword. To remove the secure unit authentication attribute from the running configuration, enter the no form of this command. This option allows inheritance of a value for secure unit authentication from another group policy.

The following example shows how to enable secure unit authentication for the group policy named FirstGroup:

Configuring User Authentication

User authentication is disabled by default. When enabled, user authentication requires that individual users behind a hardware client authenticate to gain access to the network across the tunnel. Individual users authenticate according to the order of authentication servers that you configure.

Specify whether to enable user authentication by entering the user-authentication command with the enable keyword in group-policy configuration mode.

To disable user authentication, enter the disable keyword. To remove the user authentication attribute from the running configuration, enter the no form of this command. This option allows inheritance of a value for user authentication from another group policy.

If you require user authentication on the primary ASA, be sure to configure it on any backup servers as well.

The following example shows how to enable user authentication for the group policy named FirstGroup:

Configuring an Idle Timeout

Set an idle timeout for individual users behind hardware clients by entering the user-authentication-idle-timeout command in group-policy configuration mode. If there is no communication activity by a user behind a hardware client in the idle timeout period, the ASA terminates the client’s access:

Note This timer terminates only the client’s access through the VPN tunnel, not the VPN tunnel itself.

The idle timeout indicated in response to the show uauth command is always the idle timeout value of the user who authenticated the tunnel on the Cisco Easy VPN remote device.

The minutes parameter specifies the number of minutes in the idle timeout period. The minimum is 1 minute, the default is 30 minutes, and the maximum is 35791394 minutes.

To delete the idle timeout value, enter the no form of this command. This option allows inheritance of an idle timeout value from another group policy.

To prevent inheriting an idle timeout value, enter the user-authentication-idle-timeout command with the none keyword. This command sets the idle timeout with a null value, which disallows an idle timeout and prevents inheriting an user authentication idle timeout value from a default or specified group policy.

The following example shows how to set an idle timeout value of 45 minutes for the group policy named FirstGroup:

Configuring IP Phone Bypass

You can allow Cisco IP phones to bypass individual user authentication behind a hardware client. To enable IP Phone Bypass, enter the ip-phone-bypass command with the enable keyword in group-policy configuration mode. IP Phone Bypass lets IP phones behind hardware clients connect without undergoing user authentication processes. IP Phone Bypass is disabled by default. If enabled, secure unit authentication remains in effect.

To disable IP Phone Bypass, enter the disable keyword. To remove the IP phone Bypass attribute from the running configuration, enter the no form of this command. This option allows inheritance of a value for IP Phone Bypass from another group policy:

Note You must configure mac-exempt to exempt the clients from authentication. Refer to the “Configuring Device Pass-Through” section on page 71-8 for more information.

Configuring LEAP Bypass

When LEAP Bypass is enabled, LEAP packets from wireless devices behind a VPN 3002 hardware client travel across a VPN tunnel prior to user authentication. This action lets workstations using Cisco wireless access point devices establish LEAP authentication and then authenticate again per user authentication. LEAP Bypass is disabled by default.

To allow LEAP packets from Cisco wireless access points to bypass individual users authentication, enter the leap-bypass command with the enable keyword in group-policy configuration mode. To disable LEAP Bypass, enter the disable keyword. To remove the LEAP Bypass attribute from the running configuration, enter the no form of this command. This option allows inheritance of a value for LEAP Bypass from another group policy:

Note IEEE 802.1X is a standard for authentication on wired and wireless networks. It provides wireless LANs with strong mutual authentication between clients and authentication servers, which can provide dynamic per-user, per session wireless encryption privacy (WEP) keys, removing administrative burdens and security issues that are present with static WEP keys.

Cisco Systems has developed an 802.1X wireless authentication type called Cisco LEAP. LEAP (Lightweight Extensible Authentication Protocol) implements mutual authentication between a wireless client on one side of a connection and a RADIUS server on the other side. The credentials used for authentication, including a password, are always encrypted before they are transmitted over the wireless medium.

Cisco LEAP authenticates wireless clients to RADIUS servers. It does not include RADIUS accounting services.

This feature does not work as intended if you enable interactive hardware client authentication.

Caution There might be security risks to your network in allowing any unauthenticated traffic to traverse the tunnel.

---

The following example shows how to set LEAP Bypass for the group policy named FirstGroup:

Enabling Network Extension Mode

Network extension mode lets hardware clients present a single, routable network to the remote private network over the VPN tunnel. IPsec encapsulates all traffic from the private network behind the hardware client to networks behind the ASA. PAT does not apply. Therefore, devices behind the ASA have direct access to devices on the private network behind the hardware client over the tunnel, and only over the tunnel, and vice versa. The hardware client must initiate the tunnel, but after the tunnel is up, either side can initiate data exchange.

Enable network extension mode for hardware clients by entering the nem command with the enable keyword in group-policy configuration mode:

To disable NEM, enter the disable keyword. To remove the NEM attribute from the running configuration, enter the no form of this command. This option allows inheritance of a value from another group policy.

The following example shows how to set NEM for the group policy named FirstGroup:

Configuring Backup Server Attributes

Configure backup servers if you plan on using them. IPsec backup servers let a VPN client connect to the central site when the primary ASA is unavailable.When you configure backup servers, the ASA pushes the server list to the client as the IPsec tunnel is established. Backup servers do not exist until you configure them, either on the client or on the primary ASA.

Configure backup servers either on the client or on the primary ASA. If you configure backup servers on the ASA, it pushes the backup server policy to the clients in the group, replacing the backup server list on the client if one is configured.

Note If you are using hostnames, it is wise to have backup DNS and WINS servers on a separate network from that of the primary DNS and WINS servers. Otherwise, if clients behind a hardware client obtain DNS and WINS information from the hardware client via DHCP, and the connection to the primary server is lost, and the backup servers have different DNS and WINS information, clients cannot be updated until the DHCP lease expires. In addition, if you use hostnames and the DNS server is unavailable, significant delays can occur.

To configure backup servers, enter the backup-servers command in group-policy configuration mode:

To remove a backup server, enter the no form of this command with the backup server specified. To remove the backup-servers attribute from the running configuration and enable inheritance of a value for backup-servers from another group policy, enter the no form of this command without arguments.

The clear-client-config keyword specifies that the client uses no backup servers. The ASA pushes a null server list.

The keep-client-config keyword specifies that the ASA sends no backup server information to the client. The client uses its own backup server list, if configured. This is the default.

The server1 server 2.... server10 parameter list is a space-delimited, priority-ordered list of servers for the VPN client to use when the primary ASA is unavailable. This list identifies servers by IP address or hostname. The list can be 500 characters long, and it can contain up to10 entries.

The following example shows how to configure backup servers with IP addresses 10.10.10.1 and 192.168.10.14, for the group policy named FirstGroup:

Configuring Browser Client Parameters

The following commands configure the proxy server parameters for a client.

Step 1 Configure a browser proxy server and port for a client device by entering the msie-proxy server command in group-policy configuration mode:

The default value is none. To remove the attribute from the configuration, use the no form of the command.

The line containing the proxy server IP address or hostname and the port number must be less than 100 characters long.

The following example shows how to configure the IP address 192.168.10.1 as a Microsoft Internet Explorer proxy server, using port 880, for the group policy named FirstGroup:

Step 2 Configure the browser proxy actions (“methods”) for a client device by entering the msie-proxy method command in group-policy configuration mode.

The default value is use-server. To remove the attribute from the configuration, use the no form of the command.

The available methods are as follows:

• auto-detect —Enables the use of automatic proxy server detection in the browser for the client device.
• no-modify —Leaves the HTTP browser proxy server setting in the browser unchanged for this client device.
• no-proxy— Disables the HTTP proxy setting in the browser for the client device.
• use-server— Sets the HTTP proxy server setting in the browser to use the value configured in the msie-proxy server command.

The line containing the proxy server IP address or hostname and the port number must be less than 100 characters long.

The following example shows how to configure auto-detect as the browser proxy setting for the group policy named FirstGroup:

The following example configures the proxy setting for the group policy named FirstGroup to use the server QAserver, port 1001 as the server for the client device:

Step 3 Configure browser proxy exception list settings for a local bypass on the client device by entering the msie-proxy except-list command in group-policy configuration mode. These addresses are not accessed by a proxy server. This list corresponds to the Exceptions box in the Proxy Settings dialog box.

To remove the attribute from the configuration, use the no form of the command.

• value server:port— Specifies the IP address or name of an MSIE server and port that is applied for this client device. The port number is optional.
• none— Indicates that there is no IP address/hostname or port and prevents inheriting an exception list.

By default, msie-proxy except-list is disabled.

The line containing the proxy server IP address or hostname and the port number must be less than 100 characters long.

The following example shows how to set a browser proxy exception list, consisting of the server at IP address 192.168.20.1, using port 880, for the group policy named FirstGroup:

Step 4 Enable or disable browser proxy local-bypass settings for a client device by entering the msie-proxy local-bypass command in group-policy configuration mode.

To remove the attribute from the configuration, use the no form of the command.

By default, msie-proxy local-bypass is disabled.

The following example shows how to enable browser proxy local-bypass for the group policy named FirstGroup:

Configuring Network Admission Control Parameters

The group-policy NAC commands in this section all have default values. Unless you have a good reason for changing them, accept the default values for these parameters.

The security appliance uses Extensible Authentication Protocol (EAP) over UDP (EAPoUDP) messaging to validate the posture of remote hosts. Posture validation involves the checking of a remote host for compliancy with safety requirements before the assignment of a network access policy. An Access Control Server must be configured for Network Admission Control before you configure NAC on the security appliance.

The Access Control Server downloads the posture token, an informational text string configurable on the ACS, to the security appliance to aid in system monitoring, reporting, debugging, and logging. A typical posture token is Healthy, Checkup, Quarantine, Infected, or Unknown. Following posture validation or clientless authentication, the ACS downloads the access policy for the session to the security appliance.

The following parameters let you configure Network Admission Control settings for the default group policy or an alternative group policy.

Step 1 ( Optional) Configure the status query timer period. The security appliance starts the status query timer after each successful posture validation and status query response. The expiration of this timer triggers a query for changes in the host posture, referred to as a status query. Enter the number of seconds in the range 30 through 1800. The default setting is 300.

To specify the interval between each successful posture validation in a Network Admission Control session and the next query for changes in the host posture, use the nac-sq-period command in group-policy configuration mode:

To inherit the value of the status query timer from the default group policy, access the alternative group policy from which to inherit it, then use the no form of this command:

The following example changes the value of the status query timer to 1800 seconds:

The following example inherits the value of the status query timer from the default group policy:

Step 2 ( Optional) Configure the NAC revalidation period. The security appliance starts the revalidation timer after each successful posture validation. The expiration of this timer triggers the next unconditional posture validation. The security appliance maintains posture validation during revalidation. The default group policy becomes effective if the Access Control Server is unavailable during posture validation or revalidation. Enter the interval in seconds between each successful posture validation. The range is 300 through 86400. The default setting is 36000.

To specify the interval between each successful posture validation in a Network Admission Control session, use the nac-reval-period command in group-policy configuration mode:

To inherit the value of the Revalidation Timer from the default group policy, access the alternative group policy from which to inherit it, then use the no form of this command:

The following example changes the revalidation timer to 86400 seconds:

The following example inherits the value of the revalidation timer from the default group policy:

Step 3 ( Optional) Configure the default ACL for NAC. The security appliance applies the security policy associated with the selected ACL if posture validation fails. Specify none or an extended ACL. The default setting is none. If the setting is none and posture validation fails, the security appliance applies the default group policy.

To specify the ACL to be used as the default ACL for Network Admission Control sessions that fail posture validation, use the nac-default-acl command in group-policy configuration mode:

To inherit the ACL from the default group policy, access the alternative group policy from which to inherit it, then use the no form of this command:

The elements of this command are as follows:

• acl-name— Specifies the name of the posture validation server group, as configured on the ASA using the aaa-server host command. The name must match the server-tag variable specified in that command.
• none— Disables inheritance of the ACL from the default group policy and does not apply an ACL to NAC sessions that fail posture validation.

Because NAC is disabled by default, VPN traffic traversing the ASA is not subject to the NAC Default ACL until NAC is enabled.

The following example identifies acl-1 as the ACL to be applied when posture validation fails:

The following example inherits the ACL from the default group policy:

The following example disables inheritance of the ACL from the default group policy and does not apply an ACL to NAC sessions that fail posture validation:

Step 4 Configure NAC exemptions for VPN. By default, the exemption list is empty.The default value of the filter attribute is none. Enter the vpn-nac-exempt once for each operating system (and ACL) to be matched to exempt remote hosts from posture validation.

To add an entry to the list of remote computer types that are exempt from posture validation, use the vpn-nac-exempt command in group-policy configuration mode.

To disable inheritance and specify that all hosts are subject to posture validation, use the none keyword immediately following vpn-nac-exempt.

To remove an entry from the exemption list, use the no form of this command and name the operating system (and ACL) in the entry to be removed.

To remove all entries from the exemption list associated with this group policy and inherit the list from the default group policy, use the no form of this command without specifying additional keywords.

The syntax elements for these commands are as follows:

• acl-name— Name of the ACL present in the ASA configuration.
• disable—Disables the entry in the exemption list without removing it from the list.
• filter —( Optional) filter to apply an ACL to filter the traffic if the computer matches the os name.
• none— When entered immediately after vpn-nac-exempt, this keyword disables inheritance and specifies that all hosts will be subject to posture validation.When entered immediately after filter, this keyword indicates that the entry does not specify an ACL.
• OS— Exempts an operating system from posture validation.
• os name— Operating system name. Quotation marks are required only if the name includes a space (for example, “Windows XP”).

The following example adds all hosts running Windows XP to the list of computers that are exempt from posture validation:

The following example exempts all hosts running Windows 98 that match an ACE in the ACL named acl-1:

The following example adds the same entry to the exemption list, but disables it:

The following example removes the same entry from the exemption list, regardless of whether it is disabled:

The following example disables inheritance and specifies that all hosts will be subject to posture validation:

The following example removes all entries from the exemption list:

Step 5 Enable or disable Network Admission Control by entering the following command:

To inherit the NAC setting from the default group policy, access the alternative group policy from which to inherit it, then use the no form of this command:

By default, NAC is disabled. Enabling NAC requires posture validation for remote access. If the remote computer passes the validation checks, the ACS server downloads the access policy for the ASA to enforce. NAC is disabled by default.

An Access Control Server must be present on the network.

The following example enables NAC for the group policy:

Configuring Address Pools

Configure a list of address pools for allocating addresses to remote clients by entering the address-pools command in group-policy attributes configuration mode:

The address-pools settings in this command override the local pool settings in the group. You can specify a list of up to six local address pools to use for local address allocation.

The order in which you specify the pools is significant. The ASA allocates addresses from these pools in the order in which the pools appear in this command.

To remove the attribute from the group policy and enable inheritance from other sources of group policy, use the no form of this command:

The command address-pools none disables this attribute from being inherited from other sources of policy, such as the DefaultGrpPolicy:

The command no address pools none removes the address-pools none command from the configuration, restoring the default value, which is to allow inheritance.

hostname(config-group-policy)#

The syntax elements of this command are as follows:

• address_pool— Specifies the name of the address pool configured with the ip local pool command. You can specify up to 6 local address pools.
• none— Specifies that no address pools are configured and disables inheritance from other sources of group policy.
• value— Specifies a list of up to 6 address pools from which to assign addresses.

The following example entered in config-general configuration mode, configures pool 1 and pool20 as lists of address pools to use for allocating addresses to remote clients for GroupPolicy1:

Configuring Firewall Policies

A firewall isolates and protects a computer from the Internet by inspecting each inbound and outbound individual packet of data to determine whether to allow or drop it. Firewalls provide extra security if remote users in a group have split tunneling configured. In this case, the firewall protects the user’s PC, and thereby the corporate network, from intrusions by way of the Internet or the user’s local LAN. Remote users connecting to the ASA with the VPN client can choose the appropriate firewall option.

Set personal firewall policies that the ASA pushes to the VPN client during IKE tunnel negotiation by using the client-firewall command in group-policy configuration mode. To delete a firewall policy, enter the no form of this command.

To delete all firewall policies, enter the no client-firewall command without arguments. This command deletes all configured firewall policies, including a null policy if you created one by entering the client-firewall command with the none keyword.

When there are no firewall policies, users inherit any that exist in the default or other group policy. To prevent users from inheriting such firewall policies, enter the client-firewall command with the none keyword.

The Add or Edit Group Policy window, Client Firewall tab, lets you configure firewall settings for VPN clients for the group policy being added or modified.

Note Only VPN clients running Microsoft Windows can use these firewall features. They are currently not available to hardware clients or other (non-Windows) software clients.

In the first scenario, a remote user has a personal firewall installed on the PC. The VPN client enforces firewall policy defined on the local firewall, and it monitors that firewall to make sure it is running. If the firewall stops running, the VPN client drops the connection to the ASA. (This firewall enforcement mechanism is called Are You There (AYT), because the VPN client monitors the firewall by sending it periodic “are you there?” messages; if no reply comes, the VPN client knows the firewall is down and terminates its connection to the ASA.) The network administrator might configure these PC firewalls originally, but with this approach, each user can customize his or her own configuration.

In the second scenario, you might prefer to enforce a centralized firewall policy for personal firewalls on VPN client PCs. A common example would be to block Internet traffic to remote PCs in a group using split tunneling. This approach protects the PCs, and therefore the central site, from intrusions from the Internet while tunnels are established. This firewall scenario is called push policy or Central Protection Policy (CPP). On the ASA, you create a set of traffic management rules to enforce on the VPN client, associate those rules with a filter, and designate that filter as the firewall policy. The ASA pushes this policy down to the VPN client. The VPN client then in turn passes the policy to the local firewall, which enforces it.

Overview of the Integrity Server and ASA Interaction

The VPN client software and the Integrity client software are co-resident on a remote PC. The following steps summarize the actions of the remote PC, ASA, and Integrity server in the establishment of a session between the PC and the enterprise private network:

1. The VPN client software (residing on the same remote PC as the Integrity client software) connects to the ASA and tells the ASA what type of firewall client it is.

2. After the ASA approves the client firewall type, the ASA passes Integrity server address information back to the Integrity client.

3. With the ASA acting as a proxy, the Integrity client establishes a restricted connection with the Integrity server. A restricted connection is only between the Integrity client and the Integrity server.

4. The Integrity server determines if the Integrity client is in compliance with the mandated security policies. If the Integrity client is in compliance with security policies, the Integrity server instructs the ASA to open the connection and provide the Integrity client with connection details.

5. On the remote PC, the VPN client passes connection details to the Integrity client and signals that policy enforcement should begin immediately and the Integrity client can enter the private network.

6. After the VPN connection is established, the Integrity server continues to monitor the state of the Integrity client using client heartbeat messages.

Note The current release of the ASA supports one Integrity server at a time, even though the user interfaces support the configuration of up to five Integrity servers. If the active Integrity server fails, configure another one on the ASA and then reestablish the VPN client session.

Configuring Integrity Server Support

This section describes an example procedure for configuring the ASA to support the Zone Labs Integrity servers. The procedure involves configuring address, port, connection fail timeout and fail states, and SSL certificate parameters.

To configure the Integrity server, perform the following steps:

To set the firewall client type to the Zone Labs Integrity type, enter the following command:

Setting Client Firewall Parameters

Enter the following commands to set the appropriate client firewall parameters. You can configure only one instance of each command. Table 67-4 lists the syntax elements of these commands. For more information, see the “Configuring Firewall Policies” section.

Cisco Integrated Firewall

Cisco Security Agent

No Firewall

Custom Firewall

Zone Labs Firewalls

Note When the firewall type is zonelabs-integrity, do not include arguments. The Zone Labs Integrity Server determines the policies.

Sygate Personal Firewalls

Network Ice, Black Ice Firewall:

The following example shows how to set a client firewall policy that requires Cisco Intrusion Prevention Security Agent for the group policy named FirstGroup:

Configuring Client Access Rules

Configure rules that limit the remote access client types and versions that can connect via IPsec through the ASA by using the client-access-rule command in group-policy configuration mode. Construct rules according to these guidelines:

• If you do not define any rules, the ASA permits all connection types.
• When a client matches none of the rules, the ASA denies the connection. If you define a deny rule, you must also define at least one permit rule; otherwise, the ASA denies all connections.
• For both software and hardware clients, type and version must exactly match their appearance in the show vpn-sessiondb remote display.
• The * character is a wildcard, which you can enter multiple times in each rule. For example, client-access rul e 3 deny type * version 3.* creates a priority 3 client access rule that denies all client types running release versions 3.x software.
• You can construct a maximum of 25 rules per group policy.
• There is a limit of 255 characters for an entire set of rules.
• You can enter n/a for clients that do not send client type and/or version.

To delete a rule, enter the no form of this command. This command is equivalent to the following command:

To delete all rules, enter the no client-access-rule command without arguments. This deletes all configured rules, including a null rule if you created one by issuing the client-access-rule command with the none keyword.

By default, there are no access rules. When there are no client access rules, users inherit any rules that exist in the default group policy.

To prevent users from inheriting client access rules, enter the client-access-rule command with the none keyword. The result of this command is that all client types and versions can connect.

Table 67-5 explains the meaning of the keywords and parameters in these commands.

The following example shows how to create client access rules for the group policy named FirstGroup. These rules permit Cisco VPN clients running software version 4.x, while denying all Windows NT clients:

Note The “type” field is a free-form string that allows any value, but that value must match the fixed value that the client sends to the ASA at connect time.

Configuring Group-Policy Attributes for Clientless SSL VPN Sessions

Clientless SSL VPN lets users establish a secure, remote-access VPN tunnel to the ASA using a web browser. There is no need for either a software or hardware client. Clientless SSL VPN provides easy access to a broad range of web resources and web-enabled applications from almost any computer that can reach HTTPS Internet sites. Clientless SSL VPN uses SSL and its successor, TLS1, to provide a secure connection between remote users and specific, supported internal resources that you configure at a central site. The ASA recognizes connections that need to be proxied, and the HTTP server interacts with the authentication subsystem to authenticate users. By default, clientless SSL VPN is disabled.

You can customize a configuration of clientless SSL VPN for specific internal group policies.

Note The webvpn mode that you enter from global configuration mode lets you configure global settings for clientless SSL VPN sessions. The webvpn mode described in this section, which you enter from group-policy configuration mode, lets you customize a configuration of group policies specifically for clientless SSL VPN sessions.

In group-policy webvpn configuration mode, you can specify whether to inherit or customize the following parameters, each of which is described in the subsequent sections:

• customizations
• html-content-filter
• homepage
• filter
• url-list
• port-forward
• port-forward-name
• sso server (single-signon server)
• auto-signon
• deny message
• AnyConnect Secure Mobility Client
• keep-alive ignore
• HTTP compression

In many instances, you define the webvpn attributes as part of configuring clientless SSL VPN, then you apply those definitions to specific groups when you configure the group-policy webvpn attributes. Enter group-policy webvpn configuration mode by using the webvpn command in group-policy configuration mode. Webvpn commands for group policies define access to files, URLs and TCP applications over clientless SSL VPN sessions. They also identify ACLs and types of traffic to filter. Clientless SSL VPN is disabled by default. See the description of Chapter 74, “Configuring Clientless SSL VPN” for more information about configuring the attributes for clientless SSL VPN sessions.

To remove all commands entered in group-policy webvpn configuration mode, enter the no form of this command. These webvpn commands apply to the username or group policy from which you configure them.

The following example shows how to enter group-policy webvpn configuration mode for the group policy named FirstGroup:

Applying Customization

Customizations determine the appearance of the windows that the user sees upon login. You configure the customization parameters as part of configuring clientless SSL VPN. To apply a previously defined web-page customization to change the look-and-feel of the web page that the user sees at login, enter the customization command in group-policy webvpn configuration mode:

For example, to use the customization named blueborder, enter the following command:

You configure the customization itself by entering the customization command in webvpn mode.

The following example shows a command sequence that first establishes a customization named 123 that defines a password prompt. The example then defines a group policy named testpolicy and uses the customization command to specify the use of the customization named 123 for clientless SSL VPN sessions:

Specifying a “Deny” Message

You can specify the message delivered to a remote user who logs into a clientless SSL VPN session successfully, but has no VPN privileges, by entering the deny-message command in group-policy webvpn configuration mode:

The no deny-message value command removes the message string, so that the remote user does not receive a message.

The no deny-message none command removes the attribute from the connection profile policy configuration. The policy inherits the attribute value.

The message can be up to 491 alphanumeric characters long, including special characters, spaces, and punctuation, but not counting the enclosing quotation marks. The text appears on the remote user’s browser upon login. When typing the string in the deny-message value command, continue typing even if the command wraps.

The default deny message is: “Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information.”

The first command in the following example creates an internal group policy named group2. The subsequent commands modify the attributes, including the webvpn deny message associated with that policy.

Configuring Group-Policy Filter Attributes for Clientless SSL VPN Sessions

Specify whether to filter Java, ActiveX, images, scripts, and cookies from clientless SSL VPN sessions for this group policy by using the html-content-filter command in webvpn mode. HTML filtering is disabled by default.

To remove a content filter, enter the no form of this command. To remove all content filters, including a null value created by issuing the html-content-filter command with the none keyword, enter the no form of this command without arguments. The no option allows inheritance of a value from another group policy. To prevent inheriting an html content filter, enter the html-content-filter command with the none keyword.

Using the command a second time overrides the previous setting.

Table 67-6 describes the meaning of the keywords used in this command.

The following example shows how to set filtering of JAVA and ActiveX, cookies, and images for the group policy named FirstGroup:

Specifying the User Home Page

Specify a URL for the web page that displays when a user in this group logs in by using the homepage command in group-policy webvpn configuration mode. There is no default home page.

To remove a configured home page, including a null value created by issuing the homepage none command, enter the no form of this command. The no option allows inheritance of a value from another group policy. To prevent inheriting a home page, enter the homepage none command.

The none keyword indicates that there is no home page for clientless SSL VPN sessions. It sets a null value, thereby disallowing a home page and prevents inheriting an home page.

The url-string variable following the keyword value provides a URL for the home page. The string must begin with either http:// or https://.

Configuring Auto-Signon

The auto-signon command is a single sign-on method for users of clientless SSL VPN sessions. It passes the login credentials (username and password) to internal servers for authentication using NTLM authentication, basic authentication, or both. Multiple auto-signon commands can be entered and are processed according to the input order (early commands take precedence).

You can use the auto-signon feature in three modes: webvpn configuration, webvpn group configuration, or webvpn username configuration mode. The typical precedence behavior applies where username supersedes group, and group supersedes global. The mode you choose depends upon the desired scope of authentication.

To disable auto-signon for a particular user to a particular server, use the no form of the command with the original specification of IP block or URI. To disable authentication to all servers, use the no form without arguments. The no option allows inheritance of a value from the group policy.

The following example, entered in group-policy webvpn configuration mode, configures auto-signon for the user named anyuser, using basic authentication, to servers with IP addresses ranging from 10.1.1.0 to 10.1.1.255:

The following example commands configure auto-signon for users of clientless SSL VPN sessions, using either basic or NTLM authentication, to servers defined by the URI mask https://*.example.com/*: