Table Of Contents
Release Notes for Cisco Security MARS Appliance 6.0.5
Introduction
Supported Hardware
New Features
Miscellaneous Changes and Enhancements
New Vendor Signatures
Upgrade Instructions
Important Upgrade Notes
General Notes
Upgrade to 6.0.5
Upgrade to 6.0.4
Upgrade to 6.0.3
Upgrade to 6.0.2
Upgrade to 6.0.1
Upgrade to 5.3.6
Upgrade to 4.3.6
Upgrade Path Matrix
Downloading the Upgrade Package from CCO
Documentation Errata
Important Notes
Caveats
Open Caveats for Supporting Devices
Open Caveats— Release 6.0.5
Resolved Caveats —Release 6.0.5
Resolved Caveats —Releases Prior to 6.0.5
Product Documentation
Obtaining Documentation, Obtaining Support, and Security Guidelines
Release Notes for Cisco Security MARS Appliance 6.0.5
Published: December 17, 2009
Note 
We sometimes update the printed and electronic documentation after original publication. Therefore, you should review the documentation on Cisco.com for any updates.
These release notes are for use with the Cisco Security Monitoring, Analysis, and Response System (MARS), Release 6.0.5 running on any supported MARS Appliance model listed in Supported Hardware.
This chapter contains the following topics:
•Introduction
•Supported Hardware
•New Features
•Upgrade Instructions
•Documentation Errata
•Important Notes
•Caveats
•Product Documentation
•Obtaining Documentation, Obtaining Support, and Security Guidelines
Introduction
Release 6.0.5 is now available as an upgrade of 6.0.4 of your software release in support of the MARS Appliance models as identified in Supported Hardware. Registered SMARTnet users can obtain release 6.0.5 from the Cisco support website at:
http://www.cisco.com/go/mars/
And then click the Download Software link in the Support box on the right side of the MARS product home page.
Supported Hardware
Release 6.0.5 supports the following Cisco Security MARS Appliance models:
Local Controller Appliances: 2nd Generation
•Cisco Security MARS 25R (CS-MARS-25R-K9)
•Cisco Security MARS 25 (CS-MARS-25-K9)
•Cisco Security MARS 55 (CS-MARS-55-K9)
•Cisco Security MARS 110R (CS-MARS-110R-K9)
•Cisco Security MARS 110 (CS-MARS-110-K9)
•Cisco Security MARS 210 (CS-MARS-210-K9)
Local Controller Appliances: 1st Generation
•Cisco Security MARS 20R (CS-MARS-20R-K9) as a MARS 20
•Cisco Security MARS 20 (CS-MARS-20-K9)
•Cisco Security MARS 50 (CS-MARS-50-K9)
•Cisco Security MARS 100e (CS-MARS-100E-K9) as a MARS 100
•Cisco Security MARS 100 (CS-MARS-100-K9)
•Cisco Security MARS 200 (CS-MARS-200-K9)
Global Controller Appliances: 2nd Generation
•Cisco Security MARS GC2R (CS-MARS-GC2R-K9)
•Cisco Security MARS GC2 (CS-MARS-GC2-K9)
Global Controller Appliances: 1st Generation
•Cisco Security MARS GCm (CS-MARS-GCM-K9) as a MARS GC
•Cisco Security MARS GC (CS-MARS-GC-K9)
New Features
In addition to resolved caveats, this release includes the following new features:
This section contains the following topics:
•Miscellaneous Changes and Enhancements
•New Vendor Signatures
Miscellaneous Changes and Enhancements
The following changes and enhancements exist in:
•FIPS 140-2 Level 2 Compliance for the MARS 110R—Some customers, especially those in the federal market, require secure appliance communications to use government approved encryption technologies and provide tamper protection. When used in conjunction with a Cisco FIPS 140-2 Level 2 certified PCI card, the 6.0.5 release of the MARS software enables FIPS 140-2 Level 2 compliance.
•FIPS PCI card for the MARS 110R—To enable the FIPS 140-2 Level 2 solution, customers must order a Cisco FIPS 140-2 Level 2 certified PCI card (part no. CS-MARS-FIPS-K9=) for their existing MARS 110R. The reconfigured appliance with a Cisco FIPS 140-2 Level 2 certified PCI card installed is designated a MARS 110RF model. For more information on the installation of the FIPS certified PCI card, see the CS-MARS FIPS PCI CARD Quick Install document.
•Custom Login Banner Text—According to NIST appliance hardening standards, warning banners are necessary at all access points in the event an organization wishes to prosecute an unauthorized user. CS-MARS provides a customer-defined banner message facility that can provide fair warning to unauthorized users. Banner text of up to 2,000 characters can now be configured form the MARS web interface (ADMIN > System Parameters > Banner Settings). The banner text appears on the login page and as a system message when an SSH connection is made to access the CLI.
New Vendor Signatures
The following table describes the most recent signatures supported for each product or technology:
Tip For full details on supported devices and versions, see Supported and Interoperable Devices and Software for Cisco Security MARS Local Controller 6.0.x.
Revised in 6.0.5
|
Product
|
Signature Version Supported
|
Intrusion Prevention and Detection Signatures
|
Yes
|
Cisco IDS 4.0,
Cisco IPS 5.x,
Cisco IPS 6.x
Cisco IPS 7.x
|
Current through S427 signature release.
|
Yes
|
Cisco ASA
|
Current as of August 26, 2009
|
Yes
|
Cisco IOS 12.2/12.4
|
Current as of August 26, 2009
|
Yes
|
Snort NIDS 2.8
|
Current through the August 1, 2009 signature release.
Latest signature mapped: 15901.
|
Yes
|
ISS RealSecure Network Sensor 6.5 and 7.0, and
ISS RealSecure Server Sensor 6.5 and 7.0
|
XPU 29.080
Release date: August 11, 2009
|
Yes
|
McAfee IntruShield 4.1
|
v4.1.56.13
Release date: August 27, 2009
|
Yes
|
McAfee Entercept HIDS 2.5, 4.0, 6.x
|
Current through the August 18, 2009 signature release.
|
Yes
|
CheckPoint Application Intelligence
(VPN-1 NG with Application Intelligence R65)
|
Current through the September 1, 2009 signature release.
|
Yes
|
Netscreen IDP 2.1, 3.0, 3.1, 4.0, 4.1
|
Signature version: 4.0.
Release date: September 2, 2009
|
No. EOS.
|
Symantec NIDS, v 4.0
|
Signature package: 95
Release date: June 12, 2008
|
Yes
|
Enterasys Dragon 6.x, 7.x
|
Current through the August 25, 2009 signature release.
|
No. EOS.
|
Symantec Manhunt 3.x
(See Symantec NIDS, v 4.0.) 3.4.3 Update 59
|
3.4.3 Update 59
Current through the May 24, 2007 signature release.
|
Vulnerability Scanner Signatures
|
Yes
|
Qualys Guard ANY
|
Current through the September 2, 2009 signature release.
|
Yes
|
E-Eye, Retina Scanner Vulnerability Software, version 5.6New Vendor Signatures
|
Current through the August 31, 2009 signature release.
|
Yes
|
Foundstone, version ANY
|
Current through the September 1, 2009 signature release.
|
Yes
|
Common Vulnerabilities and Exposures (CVE) Database
|
Current with the September 2, 2009 definition update.
|
Miscellaneous Support
|
No
|
Oracle 11g
|
Support for new AUDIT_ACTIONS.
|
Upgrade Instructions
The MARS upgrade packages are the primary vehicle for major, minor, and patch software releases. As administrator of the MARS Appliance, you should check the upgrade site regularly for upgrades. In addition to addressing high-priority caveats, upgrade packages update system inspection rules, event types, and provide the most recent signature support.
For detailed instructions on planning and performing an upgrade or install, refer to "Checklist for Upgrading the Appliance Software" in the Cisco Security MARS Initial Configuration and Upgrade Guide.
Important Upgrade Notes
To ensure that the upgrade from earlier releases is trouble free, this section contains the notes provided in previous releases according the release number. Please refer to the notes that pertain to the release you are upgrading from and any releases following that one.
General Notes
Note The CS-MARS 110R running the FIPS-compliant card cannot be managed by a Global Controller.
The MARS Appliance performs a file system consistency check (fsck) on all disks when either of the following conditions is met:
•If the system has not been rebooted during the past 180 days.
•If the system has been rebooted 30 times.
The fsck operation takes a long time to complete, which can result in significant unplanned downtime when rebooting the system after meeting a condition above. For example, a MARS 50 appliance can take up to 90 minutes to perform the operation.
Upgrade to 6.0.5
The 6.0.5 release is a general bug fix and signature update release for all MARS appliance models. However, it offers new functionality for an existing CS-MARS 110R when you order and install a FIPS-compliant PCI card. Once installed, you can configure FIPS-specific features within MARS. For more information, see theCS-MARS FIPS PCI CARD Quick Installdocument.
Note The CS-MARS 110R running the FIPS-compliant card cannot be managed by a Global Controller.
Upgrade to 6.0.4
No important notes exist for the 6.0.4 upgrade.
Upgrade to 6.0.3
No important notes exist for the 6.0.3 upgrade.
Upgrade to 6.0.2
No important notes exist for the 6.0.2 upgrade.
Upgrade to 6.0.1
The upgrade process to 6.0.1 differs based on the release you are upgrading from. If you are upgrading a 5.x release, then you can upgrade to 6.0.1 if you are running 5.3.6. The upgrade from 5.3.6 to 6.0.1 takes several hours, as it also upgrades the Oracle database running on the appliance. If you are running an earlier 5.x release, you must first upgrade to 5.3.6 (see Upgrade to 5.3.6 for details).
However, if you are upgrading a 4.x release, you must migrate the system instead of upgrading. To migrate from a 4.x, you must follow the step-by-step instructions specified in the Migrating Data from Cisco Security MARS 4.x to 6.0.1.
Note When upgrading a "restricted" model of MARS appliance (20R, 100e, or GCm) to MARS Software release 6.0.1, all limits enforced by the restricted model will be ignored. The "restricted" models will perform as unrestricted models (20, 100, or GC) once upgraded to release 6.0.1.
Upgrade to 5.3.6
For notes that are specific to the upgrade to the 5.3.6 release, as well as all previous 5.x releases, see the Release Notes for Cisco Security MARS Appliance 5.3.6.
Upgrade to 4.3.6
For notes that are specific to the upgrade to the 4.3.6 release, as well as all previous 4.x releases, see the Release Notes for Cisco Security MARS Appliance 4.3.6.
Upgrade Path Matrix
When upgrading from one software release to another, a prerequisite release is always required. This prerequisite release is the minimum level required to be running on the appliance before you can upgrade to the most recent release. Table 1 identifies the upgrade path that you must follow to reach the minimum level required to upgrade to current release.
Table 1 Upgrade Path Matrix
From Release
|
Upgrade To
|
Upgrade Package
|
4.3.6
|
6.0.1
|
Migration required. See Migrating Data from Cisco Security MARS 4.x to 6.0.1
|
5.3.6
|
6.0.1
|
csmars-6.0.1.3066.pkg
|
6.0.1 (3066) or 6.0.1 (3070)
|
6.0.2
|
csmars-6.0.2.3102.zip
|
6.0.2
|
6.0.3
|
csmars-6.0.3.3186.zip
|
6.0.3
|
6.0.4
|
csmars-6.0.4.3229.zip
|
6.0.4
|
6.0.5
|
csmars-6.0.5.3358.zip
|
Downloading the Upgrade Package from CCO
Upgrade images and supporting software are found on the CCO software download pages dedicated to MARS. You can access these pages at the following URLs, assuming you have a valid CCO account and that you have registered your SMARTnet contract number for your MARS Appliance
Top-level page:
•http://www.cisco.com/go/mars/
And then click the Download Software link in the Support box on the right side of the MARS product home page.
Result: The Download Software page loads.
From the Download Software page, select one of the following options:
•CS-MARS IPS Signature Updates Archives
•CS-MARS IPS Signature Updates
•CS-MARS Patches and Utilities (supplementary files)
•CS-MARS Recovery Software
•CS-MARS Upgrade Packages
Note If you are upgrading from a release earlier than those posted on CCO, please contact Cisco support for information on obtaining the required images. Do not attempt to skip releases along the upgrade path.
For information on obtaining a CCO account, see the following URL:
•http://www.cisco.com/en/US/applicat/cdcrgstr/applications_overview.html
Documentation Errata
•CSCsl14244. User guide does not discuss role of Nessus in the MARS system.
To determine whether specific incidents are false positives, MARS uses Nessus 2.x GPL plug-ins and custom scripts mapped to specific MARS event types. MARS does not use Nessus to perform vulnerability assessments or related reporting.
MARS uses Nessus as one component in determining false positives. When a host resides on a network listed under "Networks for Dynamic Vulnerability Scanning", then MARS uses Nessus to help ascertain whether an attack targeting that host was likely to be successful. When an event does not have corresponding Nessus Attack Scripting Language (NASL) script, MARS uses nmap OS fingerprinting to determine the destination operating system type, and uses nmap-found-OS to match known operating systems affected by the attack.
•CSCsk77546. Discovery Device with SSH 512 module not supported.
The OpenSSH client used by MARS does not support modulus sizes smaller than 768. For example, you cannot discover a device using a SSH login that has 512-byte key.
Important Notes
The following notes apply to the MARS 6.0.x releases:
•CSCsu50839—Report Result Page saves the previous "Other views" selection
If you change the "Other Views" options in the report result page, the changes persist for that report and for that browser. When the report results are viewed later, the browser shows the saved options but the results displayed are always the default options results.
To avoid this issue, always click Display Report to view a scheduled report's results.
•If the client system used to access the MARS GUI is not on the same side of the NAT boundary as the a MARS appliance and the Security Manager server, you can perform policy lookup in read-only mode. However, you cannot start the Security Manager client from the read-only policy lookup table to modify matching policies. The Security Manager client must be on the same side of the NAT as the MARS appliance and the Security Manager server if you want to modify the matching policy from MARS. This restriction is also true if you want to query MARS events from policies.
•The performance of the Summary Page degrades when too many reports are added under My Reports. The smaller the number of reports under My Reports, the faster the Summary page loads. To ensure adequate performance, limit the number of reports to 6. This issue is partially described in CSCse18865.
•Do not to use DISTINCT or SAME in queries, and do not run multi-line queries in Release x.3.4 through 6.0.1. If you run such a query, the system time outs after 20 minutes without returning any results. The message "Timeout Occurred" appears instead. You can use DISTINCT and SAME in a Query to create a rule with the Query interface.
•For Symantec AntiVirus, the Symantec agent hostname (AV client computer name) appears in the "Reported User" column of the event data. Therefore, you can define a query, report or rule related to this agent based on the "Reported User" value.interface. For
•The False Positive and Query pages (multi-column result format) have changed. You can now query on firing events that triggered false positives within a time interval. Such queries will render events that did not appear on the False Positive page. To ensure performance, the False Positive page only displays false positives from the most recent 10,000 firing events. To view additional false positives, you must perform a query.
The following notes describe new behavior based on the resolution of specific caveats. Be sure to check the upgrade notes for each release for important notes on data migration.
Reference Number
|
Description
|
CSCsc50636, CSCsc50652
|
Issues: Back-end IPS process runs at 99% CPU when pulling large IP Logs The Back-end IPS process reaches 1GB in memory used when pulling IP Logs. The process names depending on the version on MARS that is running:
•In release 4.2.1 and earlier, the process names are pnids50_srv and pnids40_srv.
•In release 4.2.2 and later, the process is named csips.
These related issues, are specific to pulling IP logs from Cisco IDS/ IPS devices. The symptom is that the Back-end IPS service consumes the system resources on the MARS Appliance. As an improper configuration of the sensor can significantly degrade the sensor performance as well as that of MARS.
Workaround: Ensure that settings for IP log creation on the sensor limit the size of the IP log (in terms of number of bytes or number of packets captured). Also, verify that IP packet logging is enabled only for signatures of interest and not for all signatures. In addition, the following release-specific maximums are enforced:
•In 4.2.1, a 100 file maximum is enforced for the log file queue when the MARS is configured to pull IP log files. Therefore, it may not pull every IP log file. In addition, the complete IP Log file may not be pulled, instead, data is pulled from the file starting 5 minutes before the alert was generated through the end of the file.
•In 4.2.2, a 1,000 file maximum (up from 100 in 4.2.1) is enforced for the log file queue when the MARS is configured to pull IP log files. The complete IP Log file may not be pulled, instead, data is pulled from the file starting 1 minute (down from 5 minutes in 4.2.1) before the alert was generated through the end of the file. And last, 100KB is the maximum IP log size that can be pulled from a MARS Appliance.
|
CSCpn02175
|
Issue: Data computed or stored on a standalone MARS while in standalone mode will not be transferred to a Global Controller. Only data computed on an Local Controller that is currently monitored by a Global Controller will be pushed up.
|
CSCpn02073
|
Issue: After renaming a cloud, clicking the cloud again causes an error.
Workaround: Refresh the page before clicking a renamed cloud.
|
CSCpn01270
|
Issue: The free-form search may not work for the following devices:
•Check Point Opsec NG FP3
•Cisco CSA, 4.0
•Cisco, IDS, 3.1 and 4.0
•ISS, RealSecure, 6.5 and 7.0
•Entercept Entercept, 2.5 and 4.0
•IntruVert IntruShield, 1.5
|
CSCpn00247
|
Issue: The automatic time-out feature built into the GUI does not work when the Summary page is left open with automatic refresh selected.
Resolution: Please log out of the system when you are no longer using it.
|
Caveats
This section describes the open and resolved caveats with respect to this release.
For your convenience in locating caveats in Cisco's Bug Toolkit, the caveat titles listed in this section are drawn directly from the Bug Toolkit database. These caveat titles are not intended to be read as complete sentences because the title field length is limited. In the caveat titles, some truncation of wording or punctuation may be necessary to provide the most complete and concise description. The only modifications made to these titles are as follows:
•Commands are in boldface type.
•Product names and acronyms may be standardized.
•Spelling errors and typos may be corrected.
Note If you are a registered cisco.com user, view Bug Toolkit on cisco.com at the following website:
http://www.cisco.com/support/bugtools
To become a registered cisco.com user, go to the following website:
http://tools.cisco.com/RPF/register/register.do
This section contains the following topics:
•Open Caveats for Supporting Devices
•Open Caveats— Release 6.0.5
•Resolved Caveats —Release 6.0.5
•Resolved Caveats —Releases Prior to 6.0.5
Open Caveats for Supporting Devices
The following caveats affect this release and are part of supported devices or compatible products:
Reference Number
|
Description
|
Cisco Security Manager
|
CSCsm96376
|
Policy lookup icon not shown if device is deleted from MARS
|
CSCsm94537
|
Policy lookup icon not shown for a device deleted and re-added to MARS
|
CSCsm43237
|
Minimum password length for Security Manager account in MARS
|
CSCsf31401
|
MARS query does not highlight rules inside any policy group named Local
|
Firewall Services Module
|
CSCsl27574
|
FWSM Syslog message FWSM-6-302013 with wrong Real and Mapped IP
|
Open Caveats— Release 6.0.5
The following caveats affect this release and are part of MARS.
Reference Number
|
Description
|
CSCpn00173
|
Nessus should check pre-NAT address instead of Post-NAT address
|
CSCpn00183
|
Adding devices w/o "Activate" can cause "messy" graph
|
CSCpn00212
|
Graphgen crashes when there are many non-existent devices
|
CSCpn00293
|
using TAB in editing fields
|
CSCpn00455
|
Graph doesn't refresh when a cloud is renamed
|
CSCpn00586
|
nasl message text needs to be changed
|
CSCpn00908
|
"Domain" in Configuration page - no use
|
CSCpn01134
|
Cloud name input box accepts invalid characters
|
CSCpn01219
|
Cleanup script for invalid /etc/qpage.conf entries
|
CSCpn01293
|
Host OS listing needs cleaning
|
CSCpn01319
|
pnreset command does not cause reboot
|
CSCpn01382
|
Security device type hosts don't show up in IP management
|
CSCpn01398
|
Unable to shutdown an interface
|
CSCpn01438
|
Batch Query: Under high load, some batch queries may not complete
|
CSCpn02061
|
Saving .csv files under WinXP SP2 results in .htm extension
|
CSCpn02177
|
Docs: Filesystem Check after 22 reboots
|
CSCpn02383
|
IIS parsing must be separated from Windows log
|
CSCpn02385
|
Applied $TARGET01 for GC Query Source IP resulted in "resultCounter
|
CSCpn02398
|
XML escaping errors in Keyword Search in Rule
|
CSCpn02410
|
rule was not fired because Oracle log used upper case for user
|
CSCpn02414
|
GC/LC user rule is too long to fit into a page if keyword is long
|
CSCpn02470
|
Server csv function could not handle special characters in password
|
CSCpn02511
|
need to fix errors in affected os
|
CSCpn02549
|
JavaScript Error from ViewReport when clicking Edit/Clear
|
CSCpn02558
|
"Agent" didn't be removed correctly
|
CSCpn02566
|
rebooting mars while it is upgrading cause the box not accessible
|
CSCpn02574
|
Time change on system causes GC/LC communication problem
|
CSCpn02666
|
Batch Query Results with one item returned -> no data in graph in em
|
CSCpn02869
|
Rules editing: changing entry for select window pulldown after error
|
CSCpn02901
|
GC/LC, rule does not display user <cxu> but allows such cfg
|
CSCpn02968
|
Network group search is not working for "All IP addresses"
|
CSCpn02973
|
Not able to downgrade a security analyst to Notification only user
|
CSCpn02976
|
GC:LC - Communication issues after time zone change
|
CSCpn03057
|
Copied rules have shortened year in front, which is confusing (ex. 0
|
CSCsb67871
|
Got System Error In GC After Re-installed New Version In LC
|
CSCsb77550
|
CSV-re import of CSA and Symantec agents unsuccessful
|
CSCsb80082
|
Deleting a LC w/o exchanging certificates doesn't set mode to Standalone
|
CSCsc04484
|
LC Rule/Report list shows empty after deletion of GC group
|
CSCsc59363
|
Need improvement to GUI for multi-line rules
|
CSCsc90480
|
MARS Incident notification options are not configurable
|
CSCsd61749
|
pnrestore doesn't restore all of the system config
|
CSCsd84350
|
CS-MARS/CSM: Credentials change on CSM side not checked.
|
CSCsd86896
|
Clicking the clear button when editing the query type doesn't work.
|
CSCsd89457
|
Incorrect handling of time range for rules that fire periodically.
|
CSCse09127
|
Failed load from csv returns incorrect status
|
CSCse10945
|
Summary Page Graphs Spontaneously Change Displayed Size (w/ multi-head)
|
CSCse18816
|
UI takes 99% CPU, hanging browser and slowing system while expanding all
|
CSCse31722
|
Cloud toggle only works on first page of reporting devices
|
CSCse34407
|
Query Tab -> Multi column query returns wrong results.
|
CSCse42953
|
CS-Mars - unable to show L2 path when source and destination in same net
|
CSCse45884
|
LLV query causes client CPU to go to 100%
|
CSCse51642
|
IPlanet Unknown Device Event Type Parsing Error
|
CSCse54808
|
The time stamp shown by the pndbusage command is incorrect.
|
CSCse85972
|
Unresolved symbol in Java build (though didnot stop building)
|
CSCse98029
|
Occasionally corrupted event data enters into MARS database
|
CSCsf26715
|
Inaccuracy in per-context memory utilization for multi-context devices
|
CSCsf31207
|
Mars doesn't support new/changed FWSM 3.1.3 maintenance release syslogs
|
CSCsf99844
|
wrong values for current connections using CLI "show resource usage"
|
CSCsg64119
|
rule's keyword editor treats NOT as binary rather than unary
|
CSCsg73786
|
Devices should not be added to MARS if Discovery is unsuccessful
|
CSCsg82600
|
some syslog results in unknownDET with 'Activate'
|
CSCsh00013
|
Case Management: history does indicate change of ownership
|
CSCsh44351
|
CSM multiple hostname matches failed to return multiple hosts
|
CSCsh87005
|
Support pn_client_encoding table after schema change in Bootes
|
CSCsh97060
|
MARs says it can delete up to 500 at a time but only lets you delete 50.
|
CSCsi07186
|
User can input unsupported characters in AAA device name
|
CSCsi13100
|
gui.sh dev build makes different JBOSS web.xml than make release
|
CSCsi18757
|
CS-MARS - Request to have the "ssldump" command in the MARS CLI.
|
CSCsi29398
|
CS-Mars does mitigate to the proper endpoint
|
CSCsi49285
|
Mismatch in results between query and report.
|
CSCsi49330
|
Mismatch in results between query and report when query is based on user
|
CSCsi49396
|
Mismatch in results between query & report when query based on desti. IP
|
CSCsi49419
|
The application hangs, while getting the results for a query.
|
CSCsi49474
|
Mismatch results between query and report (custom column)
|
CSCsi51999
|
Edit SW based Application device need submit twice
|
CSCsi52731
|
mars reboots w/o asking for confirmation after user clicked cfg update
|
CSCsi62384
|
The performace test kills all the process during the weekend run
|
CSCsi65960
|
L2 mitigation has problem finding path
|
CSCsi68126
|
For multiple context mode, inbound/outbound error reports are incorrect.
|
CSCsi69310
|
security hole happens if users close browsers without click logout
|
CSCsi86420
|
with 60% event rate capacity, query events ranked by time takes 20 min
|
CSCsi91734
|
Mismatch in results between query and report for All Matching Events
|
CSCsi93283
|
Mismatch between query and report results for source port ranking.
|
CSCsj15066
|
Report is not emailed because of Message exceeds maximum fixed size
|
CSCsj20697
|
LC did not get added to GC so unable to generate syslogs.
|
CSCsj23845
|
CS-MARS Action filter doesn't work if not associated with incidents
|
CSCsj28376
|
Box may not be able to reboot after recovery, under certain conditions
|
CSCsj51240
|
Paging does not work for report right after adding it to a case.
|
CSCsj66955
|
scheduled discovery is scheduled at wrong time
|
CSCsj69985
|
Syslogrelay is accepting same IP for both source and collector
|
CSCsj90505
|
Inline/Batch query not match on NAT connection report
|
CSCsj90875
|
Inline/Batch query: result mismatch on Matched Rule Ranking
|
CSCsj96592
|
Adding LC with version lower than 4.3.1 should version mismatch err
|
CSCsk04282
|
MARS failed to import 1000 hosts vulnerablilty information
|
CSCsk26308
|
pink error when listing devices while scalability script running
|
CSCsk27276
|
MARS: Isolated Networks in Topology due to 'ip unnumbered' Interface
|
CSCsk39645
|
GUI doesn't check duplicate agent ip address when adding application
|
CSCsl58216
|
MARS Layer 2 path and mitigation issues with IOS 12.3 and 12.4 version
|
CSCsm40349
|
rare crashing issue due to file system check/memory short
|
CSCso01260
|
Loading hosts from seed file does not fill interface information on MARS
|
CSCso59056
|
pnrestore throws the warning of archive version 0
|
CSCso97681
|
Host name appears inconsistently on Incident Vector Topology
|
CSCsq57230
|
custom parser performance issue
|
CSCsq69190
|
4.3.5 eth1 IP address not migrated to 5.3.5
|
CSCsq75966
|
Actual Time For 'pnexp' Or 'pnimp' Is Much Higher Than Estimated
|
CSCsq88032
|
Anomaly baselines are not part of archive/restore data
|
CSCsr41052
|
MARS not showing the switches in L2 mitigation path consistently
|
CSCsv23244
|
Unable to edit Cisco Switch IOS event parser in 6.0.1 DSF feature.
|
CSCsv40163
|
MARS adding wrong device entry after adding ISS Provetia as ISS RS 7.0
|
CSCsv66667
|
MARS not printing the correct Layer 2 topology
|
CSCsw36540
|
CSM-MARS linkage is not working when AAA is configured as Authentication
|
CSCsw80468
|
Querying events filter by severity level not generating any reports
|
CSCsx01576
|
Unable to parse NAC 4.5
|
CSCsx10815
|
Invalid insp rule propagated from GC to LC even when rule ok on GC
|
CSCsx48620
|
MARS 6.0.2 Issue with modifying user roles.
|
CSCsx51498
|
the deleted devices are still showing in the resource utilization report
|
CSCsx68259
|
MARS device support for Check Point NG FP3
|
CSCsx95786
|
User defined rule doesn't work for keyword with NOT condition
|
CSCsy15761
|
Cisco SNMP Traps with enterprise id 9 are parsed incorrectly
|
CSCsy45872
|
Unknown Device Event Type for ACS 4.2
|
CSCsz29163
|
CS-MARS Single Zone Report Showing Info from other Zones
|
CSCsz49880
|
Inactive rules becomes active after importing using DSF
|
CSCsz56227
|
Severity not evaluated/matched correctly for CSA and some IPS events
|
CSCsz78202
|
querying IPS events with prot:IP(SNMP traps) generates improper results
|
CSCsz80005
|
Mars: Changing runtime logging levels in CLI does not change it in GUI
|
CSCsz84861
|
MARS - l2 path does not show stacked switches
|
CSCsz85334
|
CS-MARS: Unable to update custom signature package
|
CSCsz85727
|
wrong info on pop up while deleting a site on GC.
|
CSCta07951
|
Older unsupported versions of checkpoint should not be supported in MARS
|
CSCta09391
|
CS-MARS-6.0-Filtering on Red severity slow and Oracle pegged.
|
CSCta49936
|
GC report with BTF site reference is always stays in progress.
|
CSCta74645
|
ASA site report takes a few seconds to display even on a non-busy box
|
CSCtb12268
|
DSF export/import feature for rules/report with sites is not working
|
CSCtb39169
|
MARS 6.0.x pulling of IDS 4.x sensors not working via rdep
|
CSCtb69227
|
CSM device causing query pink box
|
CSCtb77737
|
MARS-210 stuck at cardinarlity calculation
|
CSCtb92648
|
Custom column query with keyword doesn't return results
|
CSCtc05633
|
Cross launching from CSM causes LC / GC certificate issues
|
CSCtc25411
|
MARS: Oracle polling interval is ignored when connections are limited
|
CSCtc36976
|
CS-MARS: Custom column reports exported to CSV format missing sessions
|
Resolved Caveats —Release 6.0.5
The following customer found or previously release noted caveats have been resolved in this release.
Reference Number
|
Description
|
CSCsu50276
|
Apache Tomcat Multiple Content Length Headers Information Disclosure
|
CSCsy49888
|
All matching events with eventtype criteria doesn't give accurate result
|
CSCta70131
|
Report "Top Botnet Sites" peak/recent view has missing columns
|
CSCta75934
|
CSMARS: Scheduled Keyword-query Reports w/Special Chars Give No Results
|
CSCtb02436
|
"export all" doesn't export configuration
|
CSCtb12636
|
scheduled reports for firing events causes pink box error
|
CSCtb38233
|
CS-MARS: cross launch for IPS event from MARS to CSM fails.
|
CSCtb42495
|
pn_snmp_oid file overwritten by new datawork
|
CSCtb52450
|
Passwords of windows "pull" devices in CS-MARS log files
|
CSCtb56195
|
Migration from 6.0.4 gen1->gen2 - DB Optimization page not created
|
CSCtb65588
|
"password expired" status when adding existing LC users to GC
|
CSCtb66072
|
Keyword index falls into infinite loop when trying to close index file
|
CSCtb69246
|
Check the potential LC to GC communication problem before mid-night
|
CSCtb87141
|
CS-MARS 6.X Documentation error: Post Progress LED's description
|
CSCtc12127
|
Retrieve raw event message timeout
|
Resolved Caveats —Releases Prior to 6.0.5
For the list of caveats resolved in releases prior to this one, see the following documents:
•http://www.cisco.com/en/US/products/ps6241/prod_release_notes_list.html
Product Documentation
For the complete list of documents supporting this release, see the release-specific document roadmap:
•Cisco Secure MARS Documentation Guide and Warranty
http://www.cisco.com/en/US/products/ps6241/products_documentation_roadmaps_list.html
Lists document set that supports the MARS release and summarizes contents of each document.
•For general product information, see:
http://www.cisco.com/go/mars
Obtaining Documentation, Obtaining Support, and Security Guidelines
For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
Feedback
