Supported Hardware

These sections describe the hardware supported in Release 12.2(33)SXH and later releases:

Note ● Enter the show power command to display current system power usage.

  • Flash Memory Device Summary

– bootflash: on the RP of all supervisor engines.

– sup-bootdisk: on the SP of these supervisor engines:

Supervisor Engine 720-10GE.

Supervisor Engine 720 with a CompactFlash adapter and CompactFlash card sold by Cisco Systems, Inc., for use in Supervisor Engine 720-10GE.

Supervisor Engine 32.

– sup-bootflash: on the SP of these supervisor engines:

Supervisor Engine 720 without a CompactFlash adapter and CompactFlash card sold by Cisco Systems, Inc., for use in Supervisor Engine 720.

ME 6500.

– disk0: on these supervisor engines:

Supervisor Engine 720-10GE.

Supervisor Engine 720.

Supervisor Engine 32.

ME 6500.

– disk1: on a Supervisor Engine 720.

 

Supervisor Engines

Note For information about DRAM requirements on all supervisor engines, see this publication:

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/qa_c67_457347.html

 

Supervisor Engine 720-10GE (CAT6000-VS-S720-10G/MSFC3)

Supervisor Engine 720-10GE Common Features

  • Switch processor (SP):

– Internal 1-GB CompactFlash card (sup-bootdisk:).

– 1-GB DRAM.

  • Route processor (RP):

– Internal 64-MB bootflash.

– 1-GB DRAM.

  • One of these:

– Policy Feature Card 3CXL (PFC3CXL).

– Policy Feature Card 3C (PFC3C).

– See the “Policy Feature Cards” section.

  • Integrated 720-Gbps Switch Fabric.
  • One external slot:

– disk0:

– For CompactFlash Type II flash PC cards sold by Cisco Systems, Inc., for use in Supervisor Engine 720-10GE.

  • Console port—EIA/TIA-232 (RS-232) port.
  • Ports 1 and 2:

– QoS architecture: 2q4t / 1p3q4t

– Support for Gigabit Ethernet SFP Modules

  • Port 3:

– 10/100/1000 Mbps RJ-45

– QoS architecture: 2q4t / 1p3q4t

  • Ports 4 and 5:

– Support for 10-Gigabit Ethernet X2 tranceivers

– QoS architecture: 2q4t / 1p3q4t or 8q4t / 1p7q4t

Note The 1-Gigabit Ethernet ports and the 10-Gigabit Ethernet ports have the same QoS port architecture (2q4t/1p3q4t) unless you disable the 1-Gigabit Ethernet ports with the mls qos 10g-only global configuration command, which is required to configure DSCP-based queueing. With the 1-Gigabit Ethernet ports disabled, the QoS port architecture of the 10-Gigabit Ethernet ports is 8q4t/1p7q4t.

  • One port group: ports 1 through 5.
  • Two Universal Serial Bus (USB) 2.0 ports (not currently enabled)

Supervisor Engine 720-10GE with PFC3C and PFC3CXL

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
VS-S720-10G-3CXL

Supervisor Engine 720-10GE with PFC3CXL

12.2(33)SXH 1
VS-S720-10G-3C

Supervisor Engine 720-10GE with PFC3C

12.2(33)SXH 1

1.If there are no DFC-equipped modules installed, certain configurations require Release 12.2(33)SXH1 or later and impose configuration restrictions that are described in CSCsj95733.

Supervisor Engine 720-10GE Restrictions

  • In RPR redundancy mode, the ports on a Supervisor Engine 720-10GE in standby mode are disabled.
  • Supervisor Engine 720-10GE requires a high-capacity fan tray (see the “Fan Trays” section). All E-series chassis have a high-capacity fan tray.
  • There are no memory-only upgrade options for the Supervisor Engine 720-10GE.

Supervisor Engine 720 (CAT6000-SUP720/MSFC3)

Supervisor Engine 720 Common Features

– As an upgrade, WS-CF-UPG=

– See this publication:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_17277.html

  • Two external slots (disk0: and disk1:) for CompactFlash Type II flash PC cards sold by Cisco Systems, Inc., for use in Supervisor Engine 720.

Note Some Supervisor Engine 720 Release 12.2SX images are larger than the bootflash device and must be stored on a CompactFlash card (sup-bootdisk: or disk0: or disk1:).

  • Two Ethernet uplink ports:

– 512-KB packet buffer per port

– Port 1—Gigabit Interface Converter (GBIC)

– Port 2—Configurable as either:

• Gigabit Interface Converter (GBIC)

• 10/100/1000 Mbps RJ-45

  • QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
  • Port grouping:

– Number of ports: 2

– Number of port groups: 1

– Port ranges per port group: 1–2

  • Supervisor Engine 720 requires a high-capacity fan tray (see the “Fan Trays” section). All E-series chassis have a high-capacity fan tray.

Supervisor Engine 720 with PFC3BXL

Note If you install WS-SUP720-3BXL=, upgrade the memory on any DFC3-equipped switching modules. See this document for DFC3 memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SUP720-3BXL

Supervisor Engine 720 with PFC3BXL:

  • Switch processor (SP):

– Internal 64-MB bootflash device (sup-bootflash:)
or
internal CompactFlash card ( sup-bootdisk:)

– 1-GB or larger DRAM

  • Route processor (RP):

– 1-GB or larger DRAM

– 64-MB bootflash

12.2(17b)SXA

Supervisor Engine 720 with PFC3B

Note ● See this document for DFC3 memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

  • Use WS-F6K-PFC3BXL = to upgrade a WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3.

– If you install WS-F6K-PFC3BXL=, upgrade the memory on any DFC3-equipped switching modules.

– See this publication for more information about WS-F6K-PFC3BXL=:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16220.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SUP720-3B

Supervisor Engine 720 with PFC3B:

  • Switch processor (SP):

– Internal 64-MB bootflash device (sup-bootflash:)
or
internal CompactFlash card ( sup-bootdisk:)

– 512-MB or larger DRAM

  • Route processor (RP):

– 64-MB bootflash

– 512-MB or larger DRAM

12.2(17d)SXB1

Supervisor Engine 720 with PFC3A

Note ● See this document for DFC3 memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

  • Use WS-F6K-PFC3B= to upgrade a WS-SUP720 with a PFC3B. Use WS-F6K-PFC3BXL = to upgrade a WS-SUP720 with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3.

– If you install WS-F6K-PFC3BXL=, upgrade the memory on any DFC3-equipped switching modules.

– See this publication for more information about WS-F6K-PFC3BXL=:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16220.html

  • Except with WS-F6K-PFC3B= or WS-F6K-PFC3BXL=, do not upgrade the memory on the switch processor or the route processor on a WS-SUP720.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SUP720

Supervisor Engine 720 with PFC3A:

  • Switch processor

– Internal 64-MB bootflash device (sup-bootflash:)
or
internal 512 MB CompactFlash card ( sup-bootdisk:)

– 512-MB DRAM

  • Route processor:

– 64-MB bootflash

– 512-MB DRAM

12.2(14)SX

Supervisor Engine 32 (CAT6000-SUP32/MSFC2A)

Supervisor Engine 32 Restrictions

  • Supervisor Engine 32 requires a high-capacity fan tray (see the “Fan Trays” section). All E-series chassis have a high-capacity fan tray.
  • In some chassis, Supervisor Engine 32 requires a high-capacity power supply (see the “Power Supplies” section).
  • Supervisor Engine 32 cannot support this hardware:

– DFCs (switching modules with DFCs do not power up with a Supervisor Engine 32)

– WS-X6700 series switching modules

– WS-X6816-GBIC switching modules

– The WS-SVC-WISM-1-K9 Wireless Services Module (WiSM)

– 7600-SIP-600 SPA Interface Processor-600 and SPAs supported only in 7600-SIP-600.

  • Supervisor Engine 32 does not support this hardware:

– WS-F6K-PFC3A Policy Feature Card 3A (PFC3A)

– WS-F6K-PFC3BXL Policy Feature Card 3BXL (PFC3BXL)

– CISCO7603 3-slot chassis

  • Supervisor Engine 32 cannot support these software features and commands:

– Egress multicast replication

– Multicast replication mode detection

– All fabric configuration commands

Supervisor Engine 32 Features

Note ● See this publication for Supervisor Engine 32 hardware information:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Module_Installation/Sup_Eng_Guide/supe_gd.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SUP32-10GE-3B
WS-SUP32-GE-3B

Supervisor Engine 32:

  • One 10/100/1000 Mbps RJ-45 port
  • WS-SUP32-10GE

– Two 10-Gigabit Ethernet ports

– Requires XENPAKs

  • WS-SUP32-GE

– Eight SFP ports

– Requires Gigabit or 10/100/1000 Mbps Ethernet SFPs

  • QoS port architecture (Rx/Tx): 2q8t/1p3q8t
  • One external slot (disk0:) for CompactFlash Type II flash PC cards sold by Cisco Systems, Inc., for use in Supervisor Engine 32
  • Switch processor

– Internal 256 MB CompactFlash card (sup-bootdisk:)

– 512-MB or more DRAM (some images require more DRAM)

  • Route processor:

– Internal 64-MB bootflash

– 512-MB or more DRAM (some images require more DRAM)

12.2(18)SXF

Cisco ME 6500 Series Ethernet Switches (ME6524)

 

Product ID
(append “=” for spares)
Product Description
Minimum Software Version
ME-C6524GS-8S

Cisco ME 6500 Series Ethernet switches:

  • Switch processor (SP):

– 256-MB DRAM

– 128-MB bootflash

  • Policy Feature Card 3C (PFC3C):

– Supports a theoretical maximum of 96 K MAC addresses (64 K MAC addresses recommended maximum).

– The PFC3C operates in PFC3C mode. Enter the show platform hardware pfc mode command to display the PFC3 mode.

  • Route processor (RP)—Multilayer Switch Feature Card 2A (MSFC2A):

– 512-MB DRAM

– 64-MB bootflash

  • Fan tray: FAN-C6524
  • Power supplies: PWR-400W-DC
  • 64 chassis MAC addresses
  • Eight Gigabit Ethernet SFP ports:

– Requires Gigabit Ethernet SFPs

– 1 port group: ports 25–32

– QoS port architecture (Rx/Tx): 2q8t/1p3q8t

  • ME-C6524GS-8S:

– 24 Gigabit Ethernet SFP ports (requires Gigabit Ethernet SFPs)

– 4 port groups: ports 1–6, 7–12, 13–18, 19–24

– QoS port architecture (Rx/Tx): 1q2t/1p3q8t

  • ME-C6524GT-8S:

– 24 10/100/1000 Mbps RJ-45 Ethernet ports

– 4 port groups: ports 1–6, 7–12, 13–18, 19–24

– QoS port architecture (Rx/Tx): 1q2t/1p3q8t

12.2(33)SXH

Not supported in
12.2(33)SXJ and later releases.

ME-C6524GT-8S

 

Note See this publication for Cisco ME 6500 Series Ethernet switch hardware information:

http://www.cisco.com/en/US/products/ps6845/prod_installation_guides_list.html

Policy Feature Cards

Policy Feature Card Guidelines and Restrictions

  • The PFC3C supports a theoretical maximum of 96 K MAC addresses (64 K MAC addresses recommended maximum).
  • The PFC3A, PFC3B, and PFC3BXL support a theoretical maximum of 64 K MAC addresses (32 K MAC addresses recommended maximum).
  • The PFC3 partitions the hardware FIB table to route IPv4 unicast, IPv4 multicast, MPLS, and IPv6 unicast and multicast traffic in hardware. Traffic for routes that do not have entries in the hardware FIB table are processed by the route processor in software.

The defaults for XL mode are:

– IPv4 unicast and MPLS—512,000 routes

– IPv4 multicast and IPv6 unicast and multicast—256,000 routes

The defaults for Non-XL mode are:

– IPv4 unicast and MPLS—192,000 routes

– IPv4 multicast and IPv6 unicast and multicast—32,000 routes

Note The size of the global internet routing table plus any local routes might exceed the non-XL mode default partition sizes.

These are the theoretical maximum numbers of routes for the supported protocols (the maximums are not supported simultaneously):

– XL mode :

• IPv4 and MPLS—Up to 1,007,000 routes

• IPv4 multicast and IPv6 unicast and multicast—Up to 503,000 routes

– Non-XL mode :

• IPv4 and MPLS—Up to 239,000 routes

• IPv4 multicast and IPv6 unicast and multicast—Up to 119,000 routes

Enter the mls cef maximum-routes command to repartition the hardware FIB table. IPv4 unicast and MPLS require one hardware FIB table entry per route. IPv4 multicast and IPv6 unicast and multicast require two hardware FIB table entries per route. Changing the partition for one protocol makes corresponding changes in the partitions of the other protocols. You must enter the reload command to put configuration changes made with the mls cef maximum-routes command into effect.

Note With a non-XL-mode system, if your requirements cannot be met by repartitioning the hardware FIB table, upgrade components as necessary to operate in XL mode.

  • You cannot use one type of PFC3 on one supervisor engine and a different type on the other supervisor engine for redundancy. You must use identical policy feature cards for redundancy.
  • PFC3A—These restrictions apply to a configuration with a PFC3A and these DFCs:

– PFC3A and DFC3A—No restrictions (PFC3A mode; does not support virtual switch mode).

– PFC3A and DFC3B—The PFC3A restricts DFC3B functionality: the DFC3B functions as a DFC3A (PFC3A mode; does not support virtual switch mode).

– PFC3A and DFC3BXL—The PFC3A restricts DFC3BXL functionality: the DFC3BXL functions as a DFC3A (PFC3A mode; does not support virtual switch mode).

– PFC3A and DFC3C—The PFC3A restricts DFC3C functionality: the DFC3C functions as a DFC3A (PFC3A mode; does not support virtual switch mode).

– PFC3A and DFC3CXL—The PFC3A restricts DFC3CXL functionality: the DFC3CXL functions as a DFC3A (PFC3A mode; does not support virtual switch mode).

  • PFC3B—These restrictions apply to a configuration with a PFC3B and these DFCs:

– PFC3B and DFC3A—PFC3B functionality is restricted by the DFC3A: after a reload with a DFC3A-equipped module installed, the PFC3B functions as a PFC3A (PFC3A mode; does not support virtual switch mode).

– PFC3B and DFC3B—No restrictions (PFC3B mode; does not support virtual switch mode).

– PFC3B and DFC3BXL—The PFC3B restricts DFC3BXL functionality: after a reload with a DFC3BXL-equipped module installed, the DFC3BXL functions as a DFC3B (PFC3B mode; does not support virtual switch mode).

– PFC3B and DFC3C—The PFC3B restricts DFC3C functionality: the DFC3C functions as a DFC3B (PFC3B mode; does not support virtual switch mode).

– PFC3B and DFC3CXL—The PFC3B restricts DFC3CXL functionality: the DFC3CXL functions as a DFC3B (PFC3B mode; does not support virtual switch mode).

  • PFC3BXL—These restrictions apply to a configuration with a PFC3BXL and these DFCs:

– PFC3BXL and DFC3A—PFC3BXL functionality is restricted by the DFC3A: after a reload with a DFC3A-equipped module installed, the PFC3BXL functions as a PFC3A (PFC3A mode; does not support virtual switch mode).

– PFC3BXL and DFC3B—PFC3BXL functionality is restricted by the DFC3B: after a reload with a DFC3B-equipped module installed, the PFC3BXL functions as a PFC3B (PFC3B mode; does not support virtual switch mode).

– PFC3BXL and DFC3BXL—No restrictions (PFC3BXL mode; does not support virtual switch mode).

– PFC3BXL and DFC3C—Each restricts the functionality of the other: the PFC3BXL functions as a PFC3B and the DFC3C functions as a DFC3B (PFC3B mode; does not support virtual switch mode).

– PFC3BXL and DFC3CXL—The PFC3BXL restricts DFC3CXL functionality: the DFC3CXL functions as a DFC3BXL (PFC3BXL mode; does not support virtual switch mode).

  • PFC3C—These restrictions apply to a configuration with a PFC3C and these DFCs:

– PFC3C and DFC3A—PFC3C functionality is restricted by the DFC3A: after a reload with a DFC3A-equipped module installed, the PFC3C functions as a PFC3A (PFC3A mode; does not support virtual switch mode).

– PFC3C and DFC3B—PFC3C functionality is restricted by the DFC3B: after a reload with a DFC3B-equipped module installed, the PFC3C functions as a PFC3B (PFC3B mode; does not support virtual switch mode).

– PFC3C and DFC3BXL—PFC3C functionality is restricted by the DFC3BXL: after a reload with a DFC3BXL-equipped module installed, the PFC3C functions as a PFC3BXL (PFC3BXL mode; does not support virtual switch mode).

– PFC3C and DFC3C—No restrictions (PFC3C mode).

– PFC3C and DFC3CXL—The PFC3C restricts DFC3CXL functionality: the DFC3CXL functions as a DFC3C (PFC3C mode).

  • PFC3CXL—These restrictions apply to a configuration with a PFC3CXL and these DFCs:

– PFC3CXL and DFC3A—PFC3CXL functionality is restricted by the DFC3A: after a reload with a DFC3A-equipped module installed, the PFC3CXL functions as a PFC3A (PFC3A mode; does not support virtual switch mode).

– PFC3CXL and DFC3B—PFC3CXL functionality is restricted by the DFC3B: after a reload with a DFC3B-equipped module installed, the PFC3CXL functions as a PFC3B (PFC3B mode; does not support virtual switch mode).

– PFC3CXL and DFC3BXL—PFC3CXL functionality is restricted by the DFC3BXL: after a reload with a DFC3BXL-equipped module installed, the PFC3CXL functions as a PFC3BXL (PFC3BXL mode; does not support virtual switch mode).

– PFC3CXL and DFC3C—PFC3CXL functionality is restricted by the DFC3C: after a reload with a DFC3C-equipped module installed, the PFC3CXL functions as a PFC3C (PFC3C mode).

– PFC3CXL and DFC3CXL—No restrictions (PFC3CXL mode).

  • Switching modules that you install after bootup that are equipped with a DFC that imposes a more restricted PFC mode than the current PFC mode remain powered down.
  • You must reboot to use a switching module equipped with a DFC that imposes a more restricted PFC mode than the current PFC mode.
  • Enter the show platform hardware pfc mode command to display the PFC mode.

Policy Feature Card 3CXL

Note Use VS-F6K-PFC3CXL= to upgrade a VS-S720-10G-3C with a PFC3CXL. See this publication for more information:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16220.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
VS-F6K-PFC3CXL

Policy Feature Card 3CXL (PFC3CXL)

Supported only with Supervisor Engine 720-10GE

12.2(33)SXH

Policy Feature Card 3C

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
VS-F6K-PFC3C
ME-C6524-PFC3C

Policy Feature Card 3C (PFC3C)

With Supervisor Engine 720-10GE

12.2(33)SXH

With Cisco ME 6500 Series Ethernet switches

12.2(33)SXH

Policy Feature Card 3BXL

Note Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720 or WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3. See this publication for more information:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16220.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6K-PFC3BXL

Policy Feature Card 3BXL (PFC3BXL)

Supported only with Supervisor Engine 720

12.2(17b)SXA

Policy Feature Card 3B

Note Use WS-F6K-PFC3B= to upgrade a WS-SUP720 with a PFC3B. See this publication for more information:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16220.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6K-PFC3B

Policy Feature Card 3B (PFC3B)

With Supervisor Engine 720

12.2(17d)SXB1

With Supervisor Engine 32

12.2(18)SXF

Policy Feature Card 3A

Note WS-F6K-PFC3A is available only on WS-SUP720. It is not orderable.

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6K-PFC3A

Policy Feature Card 3A (PFC3A)

Supported only with Supervisor Engine 720

12.2(14)SX

Distributed and Centralized Forwarding Cards

Note See the “Policy Feature Cards” section for Policy Feature Cards (PFC) and Distributed Forwarding Card (DFC) restrictions.

Distributed Forwarding Card 3CXL

Note ● WS-F6700-DFC3CXL uses memory that is installed on the switching module.

  • See this publication for information about WS-F6700-DFC3CXL upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_15893.html

  • Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Version
WS-F6700-DFC3CXL

Distributed Forwarding Card 3CXL (DFC3CXL) for use on CEF720 modules

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720 and all WS-X6700 series modules

12.2(33)SXH

With Supervisor Engine 720 and WS-X6708-10GE

12.2(18)SXF5

Distributed Forwarding Card 3C

Note ● WS-F6700-DFC3C uses memory that is installed on the switching module.

  • See this publication for information about WS-F6700-DFC3C upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_15893.html

  • Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Version
WS-F6700-DFC3C

Distributed Forwarding Card 3C (DFC3C) for use on CEF720 modules

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720 and all WS-X6700 series modules

12.2(33)SXH

With Supervisor Engine 720 and WS-X6708-10GE

12.2(18)SXF5

Distributed Forwarding Card 3BXL

WS-F6700-DFC3BXL

Note ● WS-F6700-DFC3BXL uses memory that is installed on the switching module.

  • See this publication for information about WS-F6700-DFC3BXL upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_15893.html

  • Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6700-DFC3BXL

Distributed Forwarding Card 3BXL (DFC3BXL) for use on CEF720 modules

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(17d)SXB6

WS-F6K-DFC3BXL

Note ● See this publication for information about WS-F6K-DFC3BXL memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

  • Supervisor Engine 720 supports a WS-F6K-DFC3BXL on these WS-X6516-GBIC switching module hardware revisions:

– Lower than 5.0

– 5.5 and higher

  • Use with Release 12.2(33)SXH or later requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html

  • Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.
  • With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.
  • See external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:

http://www.cisco.com/en/US/ts/fn/200/fn24494.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6K-DFC3BXL

Distributed Forwarding Card 3BXL (DFC3BXL) for use on dCEF256 and CEF256 modules

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXD3

Distributed Forwarding Card 3B

WS-F6700-DFC3B

Note ● WS-F6700-DFC3B uses memory that is installed on the switching module.

  • See this publication for information about WS-F6700-DFC3B upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_15893.html

  • Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6700-DFC3B

Distributed Forwarding Card 3B (DFC3B) for use on CEF720 modules

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(17d)SXB6

WS-F6K-DFC3B

Note ● See this publication for information about WS-F6K-DFC3B memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

  • Use with Release 12.2(33)SXH or later requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html

  • Supervisor Engine 720 supports a WS-F6K-DFC3B on these WS-X6516-GBIC switching module hardware revisions:

– Lower than 5.0

– 5.5 and higher

  • Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.
  • With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.
  • See external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:

http://www.cisco.com/en/US/ts/fn/200/fn24494.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6K-DFC3B

Distributed Forwarding Card 3B (DFC3B) for use on dCEF256 and CEF256 modules

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXD3

Distributed Forwarding Card 3A

WS-F6700-DFC3A

Note ● WS-F6700-DFC3A uses memory that is installed on the switching module.

  • See this publication for information about WS-F6700-DFC3A memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

  • Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6700-DFC3A

Distributed Forwarding Card 3A (DFC3A) for use on CEF720 modules

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(17a)SX

WS-F6K-DFC3A

Note ● Not supported in virtual switch mode.

  • See this publication for information about WS-F6K-DFC3A memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

  • Use with Release 12.2(33)SXH or later requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html

  • Supervisor Engine 720 supports a WS-F6K-DFC3A on these WS-X6516-GBIC switching module hardware revisions:

– Lower than 5.0

– 5.5 and higher

  • Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.
  • With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.
  • See external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:

http://www.cisco.com/en/US/ts/fn/200/fn24494.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6K-DFC3A

Distributed Forwarding Card 3A (DFC3A) for use on dCEF256 and CEF256 modules

Supported only with Supervisor Engine 720

12.2(14)SX

Centralized Forwarding Card (WS-F6700-CFC)

Note ● There are no memory upgrade options for WS-F6700-CFC.

  • Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6700-CFC

Centralized Forwarding Card (CFC) for use on CEF720 modules

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(17a)SX

10-Gigabit Ethernet Switching Modules

76-ES+XT-4TG3CXL, 76-ES+XT-4TG3C

Note ● Not supported in PFC3A mode.

  • CDP is disabled by default on ES+ line card ports ( CSCtk12860).

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
76-ES+XT-4TG3CXL
(has DFC3CXL)
76-ES+XT-4TG3C
(has DFC3C)

Four-port Ethernet Services Plus Extended Transport (ES+XT) Line Card

  • Four 10GE ports
  • Dual fabric connections
  • Network Processors (NP):

– Port 1: NP0

– Port 2: NP1

– Port 3: NP2

– Port 4: NP3

  • Transceivers: LAN/WAN PHY, OTN/G.709

With Supervisor Engine 720-10GE

12.2(33)SXJ1

With Supervisor Engine 720

76-ES+XT-2TG3CXL, 76-ES+XT-2TG3C

Note ● Not supported in PFC3A mode.

  • CDP is disabled by default on ES+ line card ports ( CSCtk12860).

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
76-ES+XT-2TG3CXL
(has DFC3CXL)
76-ES+XT-2TG3C
(has DFC3C)

Two-port Ethernet Services Plus Extended Transport (ES+XT) Line Card

  • Two 10GE ports
  • Single fabric connection
  • Network Processors (NP):

– Port 1: NP0

– Port 2: NP1

  • Transceivers: LAN/WAN PHY, OTN/G.709

With Supervisor Engine 720-10GE

12.2(33)SXJ1

With Supervisor Engine 720

7600-ES+4TG3CXL, 7600-ES+4TG3C

Note ● Not supported in PFC3A mode.

  • CDP is disabled by default on ES+ line card ports ( CSCtk12860).

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
7600-ES+4TG3CXL
(has DFC3CXL)
7600-ES+4TG3C
(has DFC3C)

Four-port Ethernet Services Plus (ES) Line Card

  • Four 10GE ports
  • Dual fabric connections
  • Network Processors (NP):

– Port 1: NP0

– Port 2: NP1

– Port 3: NP2

– Port 4: NP3

With Supervisor Engine 720-10GE

12.2(33)SXJ1

With Supervisor Engine 720

7600-ES+2TG3CXL, 7600-ES+2TG3C

Note ● Not supported in PFC3A mode.

  • CDP is disabled by default on ES+ line card ports ( CSCtk12860).

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
7600-ES+2TG3CXL
(has DFC3CXL)
7600-ES+2TG3C
(has DFC3C)

Two-port Ethernet Services Plus (ES) Line Card

  • Two 10GE ports
  • Single fabric connection
  • Network Processors (NP):

– Port 1: NP0

– Port 2: NP1

With Supervisor Engine 720-10GE

12.2(33)SXJ1

With Supervisor Engine 720

WS-X6716-10T 16-port 10-Gigabit Ethernet Copper Switching Module

Note ● When not configured in oversubscription mode, supported in virtual switch links with Release 12.2(33)SXI and later releases.

  • The orderable product IDs are WS-X6716-10T-3C and WS-X6716-10T-3CXL.
  • The front panel is labeled WS-X6716-10T.
  • Cisco IOS software commands display “WS-X6716-10T” with either WS-F6700-DFC3C or WS-F6700-DFC3CXL.
  • To configure WS-X6716-10T port oversubscription, use the hw-module slot command.
  • In these chassis, operation of a WS-X6716-10T switching module without over-temperature alarms is supported only with operating temperatures up to 40° C:
  • WS-C6513
  • CISCO7613
  • WS-C6509
  • OSR-7609
  • WS-C6506
  • CISCO7606
  • Full NEBS-compliance requires support for operating temperatures up to 55° C, which is available in all other chassis that support WS-X6716-10T.
  • All E-Series chassis provide NEBS compliance.
  • Support in the WS-C6509-NEB-A chassis requires two FAN-MOD-09 modules.
  • Not supported in the WS-C6503, CISCO7603, or WS-C6509-NEB chassis.
  • In a 13-slot chassis, supported only in slots 9 through 13 and does not power up in other slots.
  • Does not support ISL encapsulation.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6716-10T-3CXL
(WS-X6716-10T with
WS-F6700-DFC3CXL)

WS-X6716-10T-3C
(WS-X6716-10T with
WS-F6700-DFC3C)

16-port 10-Gigabit Ethernet copper (RJ-45) module

  • dCEF720
  • Supports egress multicast replication
  • QoS port architecture (Rx/Tx):

– Oversubscription mode : 1p7q2t/1p7q4t

– Performance mode: 8q4t/1p7q4t

– Both modes support DSCP-based queueing

  • Dual switch-fabric connections
    Fabric Channel #1: ports 1–8
    Fabric Channel #2: ports 9–16
  • Number of ports: 16
    Number of port groups: 4
    Port ranges per port group: 1–4, 5–8, 9–12, 13–16

With Supervisor Engine 720-10GE

12.2(33)SXI4
(12.2(33)SXI4a
or later recommended)

With Supervisor Engine 720

WS-X6716-10G 16-port 10-Gigabit Ethernet X2 Switching Module

Note ● The orderable product IDs are WS-X6716-10G-3C and WS-X6716-10G-3CXL.

  • The front panel is labeled WS-X6716-10GE.
  • Cisco IOS software commands display “WS-X6716-10G” with either WS-F6700-DFC3C or WS-F6700-DFC3CXL.
  • To configure WS-X6716-10G port oversubscription, use the hw-module slot command.
  • In these chassis, operation of a WS-X6716-10G switching module without over-temperature alarms is supported only with operating temperatures up to 40° C:

– WS-C6513

– CISCO7613

– WS-C6509

– WS-C6509-NEB

– OSR-7609

– WS-C6506

– CISCO7606

Full NEBS-compliance requires support for operating temperatures up to 55° C, which is available in all other chassis that support WS-X6716-10G.

Note All E-Series chassis provide NEBS compliance.

  • Support in the WS-C6509-NEB-A chassis requires two FAN-MOD-09 modules.
  • WS-X6716-10G is not supported in the WS-C6503 and CISCO7603 chassis.
  • In a 13-slot chassis, WS-X6716-10G is supported only in slots 9 through 13 and does not power up in other slots.
  • With Release 12.2(33)SXH1, WS-X6716-10G ports in oversubscription mode do not support VACL capture. ( CSCsm46682)
  • Not supported in virtual switch links with Releases earlier than Release 12.2(33)SXI.
  • When not configured in oversubscription mode, supported in virtual switch links with Release 12.2(33)SXI and later releases.
  • Does not support ISL encapsulation.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6716-10G-3CXL
(WS-X6716-10G with
WS-F6700-DFC3CXL)

WS-X6716-10G-3C
(WS-X6716-10G with
WS-F6700-DFC3C)

16-port 10-Gigabit Ethernet X2 module

  • dCEF720
  • Supports egress multicast replication
  • QoS port architecture (Rx/Tx):

– Oversubscription mode : 1p7q2t/1p7q4t

– Performance mode: 8q4t/1p7q4t

– Both modes support DSCP-based queueing

  • Dual switch-fabric connections
    Fabric Channel #1: ports 1–8
    Fabric Channel #2: ports 9–16
  • Number of ports: 16
    Number of port groups: 4
    Port ranges per port group: 1–4, 5–8, 9–12, 13–16

With Supervisor Engine 720-10GE

12.2(33)SXH2

With Supervisor Engine 720

12.2(33)SXH2

WS-X6708-10GE 8-port 10-Gigabit Ethernet X2 Switching Module

Note ● WS-X6708-10G-3C and WS-X6708-10G-3CXL are the orderable product IDs.

  • The front panel is labeled WS-X6708-10GE.
  • Cisco IOS software commands display WS-X6708-10GE with either WS-F6700-DFC3C or WS-F6700-DFC3CXL.
  • To configure WS-X6708-10GE port oversubscription, use the hw-module oversubscription command.
  • In these chassis, operation of a WS-X6708-10GE switching module without over-temperature alarms is supported only with operating temperatures up to 40° C:

– WS-C6513

– CISCO7613

– WS-C6509

– WS-C6509-NEB

– OSR-7609

– WS-C6506

– CISCO7606

Full NEBS-compliance requires support for operating temperatures up to 55° C, which is available in all other chassis that support WS-X6708-10GE.

Note All E-Series chassis provide NEBS compliance.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6708-10G-3C
(WS-X6708-10GE with
WS-F6700-DFC3C)

WS-X6708-10G-3CXL
(WS-X6708-10GE with
WS-F6700-DFC3CXL)

8-port 10-Gigabit Ethernet X2 module

  • dCEF720
  • Supports egress multicast replication
  • QoS port architecture (Rx/Tx):

– Oversubscription mode : 1p7q2t/1p7q4t

– Performance mode: 8q4t/1p7q4t

– Both modes support DSCP-based queueing

  • Dual switch-fabric connections
    Fabric Channel #1: Ports 2, 3, 6, 8
    Fabric Channel #2: Ports 1, 4, 5, 7
  • Number of ports: 8
    Number of port groups: 8
    Port ranges per port group: 1 port in each group

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXF5

WS-X6704-10GE 4-port 10-Gigabit Ethernet XENPAK Switching Module

Note ● WS-X6704-10GE requires one of the following:

– WS-F6700-DFC3CXL

– WS-F6700-DFC3C

– WS-F6700-DFC3BXL (not supported in virtual switch mode)

– WS-F6700-DFC3B (not supported in virtual switch mode)

– WS-F6700-DFC3A (not supported in virtual switch mode)

– WS-F6700-CFC

  • WS-X6704-10GE ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3CXL, WS-F6700-DFC3C, WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.
  • WS-X6704-10GE is supported in the WS-C6503-E chassis.
  • WS-X6704-10GE is not supported in the WS-C6503 and CISCO7603 chassis.
  • In a 13-slot chassis, WS-X6704-10GE is supported only in slots 9 through 13 and does not power up in other slots.
  • On WS-X6704-10GE ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6704-10GE ports that interconnect network devices.
  • Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

  • Does not support ISL encapsulation.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6704-10GE

4-port 10-Gigabit Ethernet XENPAK

  • dCEF720 with a DFC
  • CEF720 with WS-F6700-CFC
  • Supports egress multicast replication
  • QoS port architecture (Rx/Tx):

– With DFC3: 8q8t/1p7q8t

– With CFC: 1q8t/1p7q8t

  • Dual switch-fabric connections
    Fabric Channel #1: Ports 3 and 4
    Fabric Channel #2: Ports 1 and 2
  • Number of ports: 4
    Number of port groups: 4
    Port ranges per port group: 1 port in each group

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720 and DFC3C or DFC3CXL

12.2(33)SXH

With Supervisor Engine 720

12.2(17a)SX

WS-X6502-10GE 1-port 10-Gigabit Ethernet Switching Module

Note ● WS-X6502-10GE does not support ISL encapsulation.

  • Use with Release 12.2(33)SXH or later and a DFC requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6502-10GE

1-port 10-Gigabit Ethernet

  • dCEF256 with a DFC
  • QoS port architecture (Rx/Tx): 1p1q8t/1p2q1t
  • Number of ports: 1
    Number of port groups: 1
    Port ranges per port group: 1 port in 1 group

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

Optical Interface Module (OIM) for WS-X6502-10GE
WS-G6488

10GBASE-LR serial 1310 nm long-reach OIM

12.2(14)SX

WS-G6483

10GBASE-ER serial 1550 nm extended-reach OIM

12.2(14)SX

Gigabit Ethernet Switching Modules

WS-X6748-SFP 48-port Gigabit Ethernet SFP Switching Module

Note ● WS-X6748-SFP requires one of the following:

– WS-F6700-DFC3CXL

– WS-F6700-DFC3C

– WS-F6700-DFC3BXL

– WS-F6700-DFC3B

– WS-F6700-DFC3A

– WS-F6700-CFC

  • WS-X6748-SFP ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3CXL, WS-F6700-DFC3C, WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.
  • WS-X6748-SFP is supported in the WS-C6503-E chassis.
  • WS-X6748-SFP is not supported in the WS-C6503 and CISCO7603 chassis.
  • In a 13-slot chassis, WS-X6748-SFP is supported only in slots 9 through 13 and does not power up in other slots.
  • On WS-X6748-SFP ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6748-SFP ports that interconnect network devices.
  • Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6748-SFP

48-port Gigabit Ethernet SFP

– With DFC3: 2q8t/1p3q8t

– With CFC: 1q8t/1p3q8t

  • Dual switch-fabric connections
    Fabric Channel #1: Ports 2, 4, 6, 8, 10, 12,
    14, 16, 18, 20, 22, 24, 26, 28, 30, 32, 34,
    36, 38, 40, 42, 44, 46, 48
    Fabric Channel #2: Ports 1, 3, 5, 7, 9, 11,
    13, 15, 17, 19, 21, 23, 25, 27, 29, 31, 33,
    35, 37, 39, 41, 43, 45, 47
  • Number of ports: 48
    Number of port groups: 4
    Port ranges per port group:
    1, 3, 5, 7, 9, 11, 13, 15, 17, 19, 21, 23
    2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24
    25, 27, 29, 31, 33, 35, 37, 39, 41, 43, 45, 47
    26, 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720 and DFC3C or DFC3CXL

12.2(33)SXH

With Supervisor Engine 720

12.2(17d)SXB

WS-X6724-SFP 24-port Gigabit Ethernet SFP Switching Module

Note ● WS-X6724-SFP requires one of the following:

– WS-F6700-DFC3CXL

– WS-F6700-DFC3C

– WS-F6700-DFC3BXL (not supported in virtual switch mode)

– WS-F6700-DFC3B (not supported in virtual switch mode)

– WS-F6700-DFC3A (not supported in virtual switch mode)

– WS-F6700-CFC

  • WS-X6724-SFP ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3CXL, WS-F6700-DFC3C, WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.
  • WS-X6724-SFP is supported in the WS-C6503-E chassis.
  • WS-X6724-SFP is not supported in the WS-C6503 and CISCO7603 chassis.
  • WS-X6724-SFP is supported in all slots of a 13-slot chassis.
  • On WS-X6724-SFP ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6724-SFP ports that interconnect network devices.
  • Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6724-SFP

24-port Gigabit Mbps Ethernet SFP

  • dCEF720 with a DFC
  • CEF720 with WS-F6700-CFC
  • Supports egress multicast replication
  • QoS architecture:

– With DFC3: 2q8t/1p3q8t

– With CFC: 1q8t/1p3q8t

  • Number of ports: 24
    Number of port groups: 2
    Port ranges per port group: 1–12, 13–24

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720 and DFC3C or DFC3CXL

12.2(33)SXH

With Supervisor Engine 720

12.2(17a)SX

WS-X6816-GBIC 16-port Gigabit Ethernet GBIC Switching Module

Note ● WS-X6816-GBIC requires one of these for use with Supervisor Engine 720-10GE or Supervisor Engine 720:

– WS-F6K-DFC3BXL

– WS-F6K-DFC3B

– WS-F6K-DFC3A

  • In a 13-slot chassis, WS-X6816-GBIC is supported only in slots 9 through 13 and does not power up in other slots.
  • Use with Release 12.2(33)SXH or later requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6816-GBIC

16-port Gigabit Ethernet GBIC

  • dCEF256
  • QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
  • Dual switch-fabric connections
    Fabric Channel #1: Ports 1–8
    Fabric Channel #2: Ports 9–16
  • Number of ports: 16
    Number of port groups: 2
    Port ranges per port group: 1–8, 9–16

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

WS-X6516A-GBIC 16-Port Gigabit Ethernet GBIC Switching Module

Note ● Use with Release 12.2(33)SXH or later requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6516A-GBIC

16-port Gigabit Ethernet GBIC

  • dCEF256 with a DFC
  • CEF256
  • 1-MB per-port packet buffers
  • Supports egress multicast replication
  • QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
  • Number of ports: 16
    Number of port groups: 2
    Port ranges per port group: 1–8, 9–16

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

WS-X6516-GBIC 16-Port Gigabit Ethernet GBIC Switching Module

Note ● Use with Release 12.2(33)SXH or later and a DFC requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html

  • Supervisor Engine 720 supports a DFC3 on these WS-X6516-GBIC hardware revisions:

– Lower than 5.0

– 5.5 and higher

  • Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC hardware revisions 5.0 through 5.4 do not power up.
  • With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC hardware revisions 5.0 through 5.4 operate in bus mode.
  • See external field notice 24494 for more information:

http://www.cisco.com/en/US/ts/fn/200/fn24494.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6516-GBIC

16-port Gigabit Ethernet GBIC

  • dCEF256 with a DFC
  • CEF256
  • 512-KB per-port packet buffers
  • QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
  • Number of ports: 16
    Number of port groups: 2
    Port ranges per port group: 1–8, 9–16

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

WS-X6416-GBIC 16-port Gigabit Ethernet GBIC Switching Module

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6416-GBIC

16-port Gigabit Ethernet GBIC

  • QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
  • Number of ports: 16
    Number of port groups: 2
    Port ranges per port group: 1–8, 9–16

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

WS-X6408A-GBIC 8-port Gigabit Ethernet GBIC Switching Module

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6408A-GBIC

8-port Gigabit Ethernet GBIC

  • QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
  • Number of ports: 8
    Number of port groups: 1
    Port ranges per port group: 1–8

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

 

With Supervisor Engine 32

12.2(18)SXF

WS-X6408-GBIC 8-port Gigabit Ethernet GBIC Switching Module

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6408-GBIC

8-port Gigabit Ethernet GBIC

  • QoS port architecture (Rx/Tx): 1q4t / 2q2t
  • Number of ports: 8
    Number of port groups: 1
    Port ranges per port group: 1–8

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

10/100/1000 Ethernet Switching Modules

WS-X6748-GE-TX

Note ● WS-X6748-GE-TX requires one of the following:

– WS-F6700-DFC3CXL

– WS-F6700-DFC3C

– WS-F6700-DFC3BXL (not supported in virtual switch mode)

– WS-F6700-DFC3B (not supported in virtual switch mode)

– WS-F6700-DFC3A (not supported in virtual switch mode)

– WS-F6700-CFC

  • WS-X6748-GE-TX ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3CXL, WS-F6700-DFC3C, WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.
  • WS-X6748-GE-TX is supported in the WS-C6503-E chassis.
  • WS-X6748-GE-TX is not supported in the WS-C6503 and CISCO7603 chassis.
  • In a 13-slot chassis, WS-X6748-GE-TX is supported only in slots 9 through 13 and does not power up in other slots.
  • On WS-X6748-GE-TX ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6748-GE-TX ports that interconnect network devices.
  • Use with Release 12.2(33)SXH or later and a DFC requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6748-GE-TX

48-port 10/100/1000 RJ-45

  • dCEF720 with a DFC
  • CEF720 with WS-F6700-CFC
  • Supports egress multicast replication
  • QoS architecture:

– With DFC3: 2q8t/1p3q8t

– With CFC: 1q8t/1p3q8t

  • Dual switch-fabric connections
    Fabric Channel #1: Ports 25–48
    Fabric Channel #2: Ports 1–24
  • Number of ports: 48
    Number of port groups: 4
    Port ranges per port group: 1–12, 13–24, 25–36, 37–48

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(17a)SX

WS-X6548-GE-TX, WS-X6548V-GE-TX, WS-X6548-GE-45AF

Note ● Release 12.2(17b)SXA and later releases provide support for more than 1 Gbps of traffic per EtherChannel on the WS-X6548-GE-TX (and voice-power daughtercard equipped) switching modules.

  • WS-X6548-GE-TX (and voice-power daughtercard equipped) switching modules do not support these features:

– DFCs

– ISL trunking

– Jumbo frames

– 802.1Q tunneling

– Traffic storm control

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6548-GE-TX
WS-X6548V-GE-TX
WS-X6548-GE-45AF

48-port 10/100/1000 Mbps

  • RJ-45
  • CEF256
  • WS-X6548-GE-TX supports:

– WS-F6K-VPWR-GE

– WS-F6K-GE48-AF

– WS-F6K-48-AF

  • WS-X6548V-GE-TX has WS-F6K-VPWR-GE
  • WS-X6548-GE-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF
  • With WS-F6K-GE48-AF, supports up to 45 ports of ePoE (16.8W).
  • QoS port architecture (Rx/Tx): 1q2t/1p2q2t
  • Number of ports: 48
    Number of port groups: 2
    Port ranges per port group: 1–24, 25–48
  • The aggregate bandwidth of each set of 8 ports (1–8, 9–16, 17–24, 25–32, 33–40, and 41–48) is 1 Gbps.

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720
(except WS-F6K-GE48-AF or WS-F6K-48-AF)

12.2(17a)SX

WS-F6K-GE48-AF or WS-F6K-48-AF
 with Supervisor Engine 720

12.2(17d)SXB

With Supervisor Engine 32

12.2(18)SXF

WS-F6K-GE48-AF or WS-F6K-48-AF
 with Supervisor Engine 32

12.2(18)SXF

WS-X6148E-GE-45AT

Note ● WS-X6148E-GE-45AT does not support:

– DFC

– Traffic storm control

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6148E-GE-45AT

48-port 10/100/1000 Mbps

  • RJ-45
  • WS-X6148E-GE-45AT has WS-F6K-48-AT (IEEE 802.3at PoE)

– With Release 12.2(33)SXJ2 and later releases, supports Class 4 PoE+: 30.00 W at the PSE (12.95 W to 25.50 W at the PD).

– With Releases earlier than Release 12.2(33)SXJ2, supports up to 45 ports of ePoE (16.8 W at the PSE, ePoE for 45 ports maximum).

  • QoS port architecture (Rx/Tx): 1q2t/1p3q8t
  • Number of ports: 48
    Number of port groups: 6
    Port ranges per port group: 1–8, 9–16, 17–24, 25–32, 33–40, 41–48
  • The aggregate bandwidth of each set of 8 ports (1–8, 9–16, 17–24, 25–32, 33–40, and 41–48) is 1 Gbps.

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXI4

With Supervisor Engine 720

With Supervisor Engine 32

WS-X6148A-GE-TX, WS-X6148A-GE-45AF

Note ● WS-X6148A-GE-TX and WS-X6148A-GE-45AF do not support these features:

– WS-F6K-DFC3A, WS-F6K-DFC3B, or WS-F6K-DFC3BXL

– Traffic storm control

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6148A-GE-TX
WS-X6148A-GE-45AF

48-port 10/100/1000 Mbps

  • RJ-45
  • WS-X6148A-GE-TX supports WS-F6K-GE48-AF or WS-F6K-48-AF
  • WS-X6148A-GE-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF
  • With WS-F6K-GE48-AF, supports up to 45 ports of ePoE (16.8W).
  • QoS port architecture (Rx/Tx): 1q2t/1p3q8t
  • Number of ports: 48
    Number of port groups: 6
    Port ranges per port group: 1–8, 9–16, 17–24, 25–32, 33–40, 41–48
  • The aggregate bandwidth of each set of 8 ports (1–8, 9–16, 17–24, 25–32, 33–40, and 41–48) is 1 Gbps.

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXF

With Supervisor Engine 32

12.2(18)SXF

WS-X6148-GE-TX, WS-X6148V-GE-TX, WS-X6148-GE-45AF

Note ● WS-X6148-GE-TX, WS-X6148V-GE-TX, and WS-X6148-GE-45AF do not support these features:

– More than 1 Gbps of traffic per EtherChannel

– WS-F6K-DFC3A, WS-F6K-DFC3B, or WS-F6K-DFC3BXL

– ISL trunking

– Jumbo frames

– 802.1Q tunneling

– Traffic storm control

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6148-GE-TX
WS-X6148V-GE-TX
WS-X6148-GE-45AF

48-port 10/100/1000 Mbps

  • RJ-45
  • WS-X6148-GE-TX supports:

– WS-F6K-VPWR-GE

– WS-F6K-GE48-AF

– WS-F6K-48-AF

  • WS-X6148V-GE-TX has WS-F6K-VPWR-GE
  • WS-X6148-GE-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF
  • With WS-F6K-GE48-AF, supports up to 45 ports of ePoE (16.8W).
  • QoS port architecture (Rx/Tx): 1q2t/1p2q2t
  • Number of ports: 48
    Number of port groups: 2
    Port ranges per port group: 1–24, 25–48
  • The aggregate bandwidth of each port group is 1 Gbps.

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720
(except WS-F6K-GE48-AF or WS-F6K-48-AF)

12.2(17a)SX

WS-F6K-GE48-AF or WS-F6K-48-AF
with Supervisor Engine 720

12.2(17d)SXB

With Supervisor Engine 32

12.2(18)SXF

WS-F6K-GE48-AF or WS-F6K-48-AF
 with Supervisor Engine 32

12.2(18)SXF

WS-X6516-GE-TX

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6516-GE-TX

16-port 10/100/1000BASE-T

  • dCEF256 with a DFC
  • CEF256
  • QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
  • Number of ports: 16
    Number of port groups: 2
    Port ranges per port group: 1–8, 9–16

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

Fast Ethernet Switching Modules

Note Fast Ethernet switching modules are not supported in VSS mode.

WS-X6148-FE-SFP

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6148-FE-SFP

48-port 100BASE-FX

  • Requires Fast Ethernet SFPs
  • QoS port architecture (Rx/Tx): 1p1q4t/1p3q8t
  • Number of ports: 48
    Number of port groups: 3
    Port ranges per port group: 1–16, 17–32, and 33–48

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXF

With Supervisor Engine 32

12.2(18)SXF

WS-X6524-100FX-MM

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6524-100FX-MM

24-port 100FX Ethernet multimode

  • dCEF256 with a DFC
  • CEF256
  • QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t
  • Number of ports: 24
    Number of port groups: 1
    Port ranges per port group: 1–24

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

WS-X6324-100FX-MM

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6324-100FX-MM

24-port 100FX Ethernet

  • Single mode and multimode MT-RJ
  • 128-KB per-port packet buffers
  • QoS port architecture (Rx/Tx): 1q4t / 2q2t
  • Number of ports: 24
    Number of port groups: 2
    Port ranges per port group: 1–12, 13–24

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

Ethernet/Fast Ethernet (10/100) Switching Modules

Note Ethernet/Fast Ethernet (10/100) switching modules are not supported in VSS mode.

WS-X6548-RJ-45

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6548-RJ-45

48-port 10/100TX RJ-45

  • dCEF256 with a DFC
  • CEF256
  • QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t
  • Number of ports: 48
    Number of port groups: 1
    Port ranges per port group: 1–48

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

WS-X6548-RJ-21

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6548-RJ-21

48-port 10/100TX RJ-21

  • dCEF256 with a DFC
  • CEF256
  • QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t
  • Number of ports: 48
    Number of port groups: 1
    Port ranges per port group: 1–48

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

WS-X6148X2-RJ-45, WS-X6148X2-45AF

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6148X2-RJ-45
WS-X6148X2-45AF

96-port 10/100TX RJ-45

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXF3

With Supervisor Engine 32

12.2(18)SXF3

WS-X6196-RJ-21, WS-X6196-21AF

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6196-RJ-21
WS-X6196-21AF

96-port 10/100TX RJ-21

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXF3

With Supervisor Engine 32

12.2(18)SXF3

WS-X6348-RJ-45, WS-X6348-RJ-45V

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6348-RJ-45
WS-X6348-RJ-45V

48-port 10/100TX RJ-45

  • 128-KB per-port packet buffers
  • QoS port architecture (Rx/Tx): 1q4t / 2q2t
  • WS-X6348-RJ-45 supports WS-F6K-VPWR
  • WS-X6348-RJ-45V has WS-F6K-VPWR
  • Number of ports: 48
    Number of port groups: 4
    Port ranges per port group: 1–12, 13–24, 25–36, 37–48

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

WS-X6348-RJ-21V

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6348-RJ-21V

48-port 10/100TX RJ-21

  • 128-KB per-port packet buffers
  • QoS port architecture (Rx/Tx): 1q4t / 2q2t
  • Has WS-F6K-VPWR
  • Number of ports: 48
    Number of port groups: 4
    Port ranges per port group: 1–12, 13–24, 25–36, 37–48

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

WS-X6148A-RJ-45, WS-X6148A-45AF

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6148A-RJ-45
WS-X6148A-45AF

48-port 10/100TX RJ-45

  • 5.3-MB per-port packet buffers
  • QoS port architecture (Rx/Tx): 1p1q4t/1p3q8t
  • WS-X6148A-RJ-45 supports WS-F6K-GE48-AF or WS-F6K-48-AF
  • WS-X6148A-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF
  • Number of ports: 48
    Number of port groups: 6
    Port ranges per port group: 1–8, 9–16, 17–24, 25–32, 33–40, 41–48

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXF

With Supervisor Engine 32

12.2(18)SXF

WS-X6148-RJ-45, WS-X6148-RJ45V, WS-X6148-45AF

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6148-RJ-45
WS-X6148-RJ45V
WS-X6148-45AF

48-port 10/100TX RJ-45

  • 128-KB per-port packet buffers
  • QoS port architecture (Rx/Tx): 1q4t / 2q2t
  • WS-X6148-RJ-45 supports WS-F6K-VPWR
  • WS-X6148-RJ-45V has WS-F6K-VPWR
  • WS-X6148-45AF has WS-F6K-48-AF
  • Number of ports: 48
    Number of port groups: 4
    Port ranges per port group: 1–12, 13–24, 25–36, 37–48

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720
(except with WS-F6K-48-AF)

12.2(14)SX

WS-F6K-48-AF with Supervisor Engine 720

12.2(17d)SXB

With Supervisor Engine 32

12.2(18)SXF

WS-F6K-48-AF with Supervisor Engine 32

WS-X6148-RJ-21, WS-X6148-RJ21V, WS-X6148-21AF

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6148-RJ-21
WS-X6148-RJ21V
WS-X6148-21AF

48-port 10/100TX RJ-21

  • 128-KB per-port packet buffers
  • QoS port architecture (Rx/Tx): 1q4t / 2q2t
  • WS-X6148-RJ-21 supports WS-F6K-VPWR
  • WS-X6148-RJ-21V has WS-F6K-VPWR
  • WS-X6148-21AF has WS-F6K-48-AF
  • Number of ports: 48
    Number of port groups: 4
    Port ranges per port group: 1–12, 13–24, 25–36, 37–48

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720
(except with WS-F6K-48-AF)

12.2(14)SX

WS-F6K-48-AF with Supervisor Engine 720

12.2(17d)SXB

With Supervisor Engine 32

12.2(18)SXF

WS-F6K-48-AF with Supervisor Engine 32

Power over Ethernet Daughtercards

Note The IEEE 802.3at power over ethernet (PoE) daughtercard is available only with the WS-X6148E-GE-45AT switching module.

WS-F6K-FE48X2-AF

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6K-FE48X2-AF

IEEE 802.3af PoE daughtercard for WS-X6148X2-RJ-45 and WS-X6196-RJ-21.

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXF

With Supervisor Engine 32

12.2(18)SXF

WS-F6K-GE48-AF, WS-F6K-48-AF

Note ● WS-F6K-GE48-AF and WS-F6K-48-AF are not FRUs for these switching modules:

– WS-X6148-RJ-45 or WS-X6148-RJ-45V (replace with WS-X6148-45AF-UG=).

– WS-X6148-RJ-21 or WS-X6148-RJ-21V (replace with WS-X6148-21AF-UG=).

  • With WS-X6548-GE-TX, WS-X6148-GE-TX, and WS-X6148A-GE-TX, supports up to 45 ports of ePoE (16.8W).

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6K-GE48-AF
WS-F6K-48-AF

IEEE 802.3af PoE daughtercard for:

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(17d)SXB

WS-F6K-VPWR-GE

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6K-VPWR-GE

Prestandard PoE daughtercard for WS-X6548-GE-TX and WS-X6148-GE-TX

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(17a)SX

With Supervisor Engine 32

12.2(18)SXF

WS-F6K-VPWR

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-F6K-VPWR

Prestandard PoE daughtercard for:

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

Transceivers

X2 Modules

Note ● WS-X6708-10GE and WS-X6716-10G do not support X2 modules shipped before the release of WS-X6708-10GE with Release 12.2(18)SXF5. The unsupported X2 modules are labeled with a number that ends with -01. (This restriction does not apply to X2-10GB-LRM.)

  • All X2 modules shipped since WS-X6716-10G became available provide EMI compliance with WS-X6716-10G.
  • Some X2 modules shipped before WS-X6716-10G became available might not provide EMI compliance with WS-X6716-10G. See the information listed for each type of X2 module in the following table.
  • For information about X2 modules, see the Cisco 10GBASE X2 Modules data sheet:

http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6574/product_data_sheet0900aecd801f92aa.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
CVR-X2-SFP10G

10G X2 to SFP+ Converter

12.2(33)SXI2


10 Gbps Ethernet SFP+ Modules

SFP-10G-LR—10GBASE-LR 1310 nm SMF

12.2(33)SXJ1

SFP-10G-LRM—10GBASE-LRM 1310 nm MMF and SMF

12.2(33)SXI4

(12.2(33)SXI4a
or later recommended)

SFP-10G-SR—10GBASE-SR 850 nm MMF

12.2(33)SXI2

SFP-H10GB-CU1M—1m Twinax cable, passive, 30AWG cable assembly

SFP-H10GB-CU3M—3m Twinax cable, passive, 30AWG cable assembly

SFP-H10GB-CU5M—5m Twinax cable, passive, 24AWG cable assembly
DWDM-X2-60.61=

10GBASE-DWDM 1560.61 nm X2 (100-GHz ITU grid)

ITU 21

12.2(33)SXI

DWDM-X2-59.79=

10GBASE-DWDM 1559.79 nm X2 (100-GHz ITU grid)

ITU 22

DWDM-X2-58.98=

10GBASE-DWDM 1558.98 nm X2 (100-GHz ITU grid)

ITU 23

DWDM-X2-58.17=

10GBASE-DWDM 1558.17 nm X2 (100-GHz ITU grid)

ITU 24

DWDM-X2-56.55=

10GBASE-DWDM 1556.55 nm X2 (100-GHz ITU grid)

ITU 26

DWDM-X2-55.75=

10GBASE-DWDM 1555.75 nm X2 (100-GHz ITU grid)

ITU 27

DWDM-X2-54.94=

10GBASE-DWDM 1554.94 nm X2 (100-GHz ITU grid)

ITU 28

DWDM-X2-54.13=

10GBASE-DWDM 1554.13 nm X2 (100-GHz ITU grid)

ITU 29

DWDM-X2-52.52=

10GBASE-DWDM 1552.52 nm X2 (100-GHz ITU grid)

ITU 31

DWDM-X2-51.72=

10GBASE-DWDM 1551.72 nm X2 (100-GHz ITU grid)

ITU 32

DWDM-X2-50.92=

10GBASE-DWDM 1550.92 nm X2 (100-GHz ITU grid)

ITU 33

DWDM-X2-50.12=

10GBASE-DWDM 1550.12 nm X2 (100-GHz ITU grid)

ITU 34

DWDM-X2-48.51=

10GBASE-DWDM 1548.51 nm X2 (100-GHz ITU grid)

ITU 36

DWDM-X2-47.72=

10GBASE-DWDM 1547.72 nm X2 (100-GHz ITU grid)

ITU 37

DWDM-X2-46.92=

10GBASE-DWDM 1546.92 nm X2 (100-GHz ITU grid)

ITU 38

DWDM-X2-46.12=

10GBASE-DWDM 1546.12 nm X2 (100-GHz ITU grid)

ITU 39

DWDM-X2-44.53=

10GBASE-DWDM 1544.53 nm X2 (100-GHz ITU grid)

ITU 41

DWDM-X2-43.73=

10GBASE-DWDM 1543.73 nm X2 (100-GHz ITU grid)

ITU 42

DWDM-X2-42.94=

10GBASE-DWDM 1542.94 nm X2 (100-GHz ITU grid)

ITU 43

DWDM-X2-42.14=

10GBASE-DWDM 1542.14 nm X2 (100-GHz ITU grid)

ITU 44

DWDM-X2-40.56=

10GBASE-DWDM 1540.56 nm X2 (100-GHz ITU grid)

ITU 46

DWDM-X2-39.77=

10GBASE-DWDM 1539.77 nm X2 (100-GHz ITU grid)

ITU 47

DWDM-X2-38.98=

10GBASE-DWDM 1538.98 nm X2 (100-GHz ITU grid)

ITU 48
DWDM-X2-38.19=

10GBASE-DWDM 1538.19 nm X2 (100-GHz ITU grid)

ITU 49
DWDM-X2-36.61=

10GBASE-DWDM 1536.61 nm X2 (100-GHz ITU grid)

ITU 51
DWDM-X2-35.82=

10GBASE-DWDM 1535.82 nm X2 (100-GHz ITU grid)

ITU 52
DWDM-X2-35.04=

10GBASE-DWDM 1535.04 nm X2 (100-GHz ITU grid)

ITU 53
DWDM-X2-34.25=

10GBASE-DWDM 1534.25 nm X2 (100-GHz ITU grid)

ITU 54
DWDM-X2-32.68=

10GBASE-DWDM 1532.68 nm X2 (100-GHz ITU grid)

ITU 56
DWDM-X2-31.90=

10GBASE-DWDM 1531.90 nm X2 (100-GHz ITU grid)

ITU 57
DWDM-X2-31.12=

10GBASE-DWDM 1531.12 nm X2 (100-GHz ITU grid)

ITU 58
DWDM-X2-30.33=

10GBASE-DWDM 1530.33 nm X2 (100-GHz ITU grid)

ITU 59
X2-10GB-T

10GBASE-T X2 Module for CAT6A/CAT7 copper cable

12.2(33)SXJ1
X2-10GB-ZR

10GBASE-ZR X2 Module for SMF

12.2(33)SXI

X2-10GB-CX4

10GBASE for CX4 (copper) cable

12.2(18)SXF5

X2-10GB-ER

10GBASE-ER Serial 1550-nm extended-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

Note X2-10GB-ER modules labeled with a number that ends with -02 do not provide EMI compliance with WS-X6716-10G.

12.2(18)SXF5

X2-10GB-LR

10GBASE-LR Serial 1310-nm long-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

Note X2-10GB-LR modules labeled with a number that ends with -02 or -03 do not provide EMI compliance with WS-X6716-10G.

12.2(18)SXF5

X2-10GB-LRM

10GBASE-LRM for FDDI-grade multimode fiber (MMF)

Note Not supported by the show idprom command. (CSCsj35671)

12.2(18)SXF8

X2-10GB-LX4

10GBASE-LX4 Serial 1310-nm multimode (MMF)

Note

  • See field notice 62840 for information about unsupported 10GBASE-LX4 modules:

http://www.cisco.com/en/US/ts/fn/misc/FN62840.html

12.2(18)SXF5

X2-10GB-SR

10GBASE-SR Serial 850-nm short-reach multimode (MMF)

12.2(18)SXF5

XENPAKs

Note ● For information about DWDM XENPAKs, see the Cisco 10GBase DWDM XENPAK Modules data sheet:

http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6576/product_data_sheet0900aecd801f9333.html

  • For information about other XENPAKs, see the Cisco 10GBASE XENPAK Modules data sheet:

http://www.cisco.com/en/US/prod/collateral/modules/ps2797/ps5138/product_data_sheet09186a008007cd00_ps5251_Products_Data_Sheet.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
XENPAK-10GB-LRM

10GBASE-LRM XENPAK Module for MMF

Note Not supported by the show idprom command. (CSCsl21260)

12.2(33)SXH1

DWDM-XENPAK

10GBASE dense wavelength-division multiplexing (DWDM) 100-GHz ITU grid

12.2(18)SXE

WDM-XENPAK-REC

10GBASE receive-only wavelength division multiplexing (WDM)

12.2(18)SXE

XENPAK-10GB-CX4

10GBASE for CX4 (copper) cable; uses Infiniband connectors

12.2(17d)SXB1

XENPAK-10GB-ER

10GBASE-ER Serial 1550-nm extended-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

Note XENPAK-10GB-ER units with Part No. 800-24557-01 are not supported, as described in this external field notice (CSCee47030):

http://www.cisco.com/en/US/ts/fn/200/fn29736.html

12.2(17a)SX

XENPAK-10GB-ER+

10GBASE-ER Serial 1550-nm extended-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

12.2(17a)SX

XENPAK-10GB-LR

10GBASE-LR Serial 1310-nm long-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

12.2(17a)SX

XENPAK-10GB-LR+

10GBASE-LR Serial 1310-nm long-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

12.2(17a)SX

XENPAK-10GB-LW

10GBASE-LW XENPAK Module with WAN PHY for SMF

Note XENPAK-10GB-LW operates at an interface speed compatible with SONET/SDH OC-192/STM-64. XENPAK-10GB-LW links might go up and down if the data rate exceeds 9Gbs. (CSCsi58211)

12.2(18)SXE

XENPAK-10GB-LX4

10GBASE-LX4 Serial 1310-nm multimode (MMF)

12.2(17a)SX1

XENPAK-10GB-SR

10GBASE-SR Serial 850-nm short-reach multimode (MMF)

12.2(17a)SX1

XENPAK-10GB-ZR

10GBASE for any SMF type

12.2(18)SXF

Small Form-Factor Pluggable (SFP) Modules

These sections describe SFPs:

Gigabit Ethernet SFP Modules

Note ● For information about coarse wavelength-division multiplexing (CWDM) SFPs, see the Cisco CWDM GBIC and SFP Solutions data sheet:

http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6575/product_data_sheet09186a00801a557c_ps4999_Products_Data_Sheet.html

  • For information about DWDM SFPs, see the Cisco Dense Wavelength-Division Multiplexing Small Form-Factor Pluggable Module data sheet:

http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6576/product_data_sheet0900aecd80582763.html

  • See the “Unsupported Hardware” section for information about unsupported DWDM-SFPs.
  • For information about other SFPs, see the Cisco SFP Optics For Gigabit Ethernet Applications data sheet:

http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6577/product_data_sheet0900aecd8033f885.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
GLC-BX-D

1000BASE-BX10 SFP module for single-strand SMF, 1490-nm TX/1310-nm RX wavelength

12.2(18)SXE

GLC-BX-U

1000BASE-BX10 SFP module for single-strand SMF, 1310-nm TX/1490-nm RX wavelength

12.2(18)SXE

GLC-LH-SMD
GLC-LH-SM

1000BASE-LX/LH SFP

12.2(17a)SX

GLC-SX-MMD
GLC-SX-MM

1000BASE-SX SFP

12.2(14)SX

GLC-T

1000BASE-T 10/100/1000 SFP module

Note Supported only at 1000 Mbps.

12.2(17a)SX

GLC-ZX-SM

1000BASE-ZX SFP module

12.2(17d)SXB1

CWDM-SFP-1470

CWDM 1470-nm (Gray) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module

12.2(17a)SX

CWDM-SFP-1490

CWDM 1490-nm (Violet) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module

12.2(17a)SX

CWDM-SFP-1510

CWDM 1510-nm (Blue) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module

12.2(17a)SX

CWDM-SFP-1530

CWDM 1530-nm (Green) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module

12.2(17a)SX

CWDM-SFP-1550

CWDM 1550-nm (Yellow) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module

12.2(17a)SX

CWDM-SFP-1570

CWDM 1570-nm (Orange) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module

12.2(17a)SX

CWDM-SFP-1590

CWDM 1590-nm (Red) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module

12.2(17a)SX

CWDM-SFP-1610

CWDM 1610-nm (Brown) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module

12.2(17a)SX

DWDM-SFP-5817

1000BASE-DWDM 1558.17 nm SFP (100-GHz ITU grid) SFP module

12.2(33)SXH

DWDM-SFP-5252

1000BASE-DWDM 1552.52 nm SFP (100-GHz ITU grid) SFP module

12.2(33)SXH

DWDM-SFP-5172

1000BASE-DWDM 1551.72 nm SFP (100-GHz ITU grid) SFP module

12.2(33)SXH

DWDM-SFP-5012

1000BASE-DWDM 1550.12 nm SFP (100-GHz ITU grid) SFP module

12.2(33)SXH

DWDM-SFP-4692

1000BASE-DWDM 1546.92 nm SFP (100-GHz ITU grid) SFP module

12.2(33)SXH

DWDM-SFP-4373

1000BASE-DWDM 1543.73 nm SFP (100-GHz ITU grid) SFP module

12.2(33)SXH

DWDM-SFP-4214

1000BASE-DWDM 1542.14 nm SFP (100-GHz ITU grid) SFP module

12.2(33)SXH

DWDM-SFP-3977

1000BASE-DWDM 1539.77 nm SFP (100-GHz ITU grid) SFP module

12.2(33)SXH

DWDM-SFP-3898

1000BASE-DWDM 1538.98 nm SFP (100-GHz ITU grid) SFP module

12.2(33)SXH

DWDM-SFP-3582

1000BASE-DWDM 1535.82 nm SFP (100-GHz ITU grid) SFP module

12.2(33)SXH

DWDM-SFP-3504

1000BASE-DWDM 1535.04 nm SFP (100-GHz ITU grid) SFP module

12.2(33)SXH

DWDM-SFP-6061

1000BASE-DWDM 1560.61 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-5979

1000BASE-DWDM 1559.79 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-5898

1000BASE-DWDM 1558.98 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-5655

1000BASE-DWDM 1556.55 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-5575

1000BASE-DWDM 1555.75 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-5494

1000BASE-DWDM 1554.94 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-5413

1000BASE-DWDM 1554.13 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-5092

1000BASE-DWDM 1550.92 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-4851

1000BASE-DWDM 1548.51 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-4772

1000BASE-DWDM 1547.72 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-4612

1000BASE-DWDM 1546.12 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-4453

1000BASE-DWDM 1544.53 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-4294

1000BASE-DWDM 1542.94 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-4056

1000BASE-DWDM 1540.56 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-3819

1000BASE-DWDM 1538.19 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-3661

1000BASE-DWDM 1536.61 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-3425

1000BASE-DWDM 1534.25 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-3268

1000BASE-DWDM 1532.68 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-3190

1000BASE-DWDM 1531.90 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-3112

1000BASE-DWDM 1531.12 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-3033

1000BASE-DWDM 1530.33 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

Fast Ethernet SFP+ Modules

Note ● Fast Ethernet SFPs are supported in these modules:

– CAT6000-VS-S720-10G/MSFC3

– ME6524

– WS-X6148-FE-SFP

  • For information about Fast Ethernet SFPs, see the Cisco 100BASE-X SFP For Fast Ethernet SFP Ports data sheet:

http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6578/product_data_sheet0900aecd801f931c.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
GLC-FE-100BX-U

100BASE-BX10-U SFP

12.2(18)SXF2

GLC-FE-100BX-D

100BASE-BX10-D SFP

12.2(18)SXF2

GLC-FE-100EX

100BASEEX SFP

12.2(18)SXF

GLC-FE-100ZX

100BASEZX SFP

12.2(18)SXF

GLC-FE-100FX

100BASEFX SFP

12.2(18)SXF

GLC-FE-100LX

100BASELX SFP

12.2(18)SXF

Note GLC-GE-100FX Fast Ethernet SFPs are not supported.

Gigabit Interface Converters (GBICs)

Note The support listed in this section applies to all modules that use GBICs.

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WDM-GBIC-REC

Receive-only wavelength division multiplexing (WDM) GBIC

12.2(18)SXE

DWDM-GBIC

Dense wavelength division multiplexing (DWDM) GBIC

12.2(17a)SX

CWDM-GBIC-1470

Cisco 1000BASE-CWDM GBIC, 1470 nm (Gray)

12.2(17a)SX

CWDM-GBIC-1490

Cisco 1000BASE-CWDM GBIC, 1490 nm (Violet)
CWDM-GBIC-1510

Cisco 1000BASE-CWDM GBIC, 1510 nm (Blue)
CWDM-GBIC-1530

Cisco 1000BASE-CWDM GBIC, 1530 nm (Green)
CWDM-GBIC-1550

Cisco 1000BASE-CWDM GBIC, 1550 nm (Yellow)
CWDM-GBIC-1570

Cisco 1000BASE-CWDM GBIC, 1570 nm (Orange)
CWDM-GBIC-1590

Cisco 1000BASE-CWDM GBIC, 1590 nm (Red)
CWDM-GBIC-1610

Cisco 1000BASE-CWDM GBIC, 1610 nm (Brown)
WS-G5483

1000BASET GBIC

12.2(14)SX

WS-G5484

Short wavelength, 1000BASE-SX

12.2(14)SX

WS-G5486

Long wavelength/long haul, 1000BASE-LX/LH

12.2(14)SX

WS-G5487

Extended distance, 1000BASE-ZX

12.2(14)SX

Shared Port Adapter (SPA) Interface Processors (SIPs)

Note ● SIPs are supported only in images that contain “_wan” in the image name.

 

 

Product ID
(append “=” for spares)
Product Description
Minimum
Software
Versions
7600-SIP-600

SPA Interface Processor-600

Note

  • 7600-SIP-600 has a WS-F6700-DFC3BXL.
  • Not supported with Supervisor Engine 32.
  • In Release 12.2(33)SXJ1 and later releases, CDP is disabled by default on 7600-SIP-600 ports ( CSCtk12860).

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXI

With Supervisor Engine 720

Note

  • Not supported in PFC3A mode.
  • Not supported in release 12.2(33)SXH and rebuilds.

12.2(18)SXF
12.2(33)SXI
7600-SIP-400

SPA Interface Processor-400

With Supervisor Engine 720-10GE in VSS mode

12.2(33)SXI4

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720 (not supported in PFC3A mode)

12.2(18)SXE

With Supervisor Engine 32

12.2(18)SXF
7600-SIP-200

SPA Interface Processor-200

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXE

With Supervisor Engine 32

12.2(18)SXF

Shared Port Adapters (SPAs)

These sections describe SPAs:

Ethernet SPAs

These sections describe Ethernet SPAs:

10-Gigabit Ethernet SPAs

Note Release 12.2(33)SXH and rebuilds do not support 7600-SIP-600.

 

Product ID

(append “=” for spares)

SIP Support
Product Description
Minimum
Software
Versions
SPA-1X10GE-L-V2

7600-SIP-400

1-Port 10 Gigabit Ethernet SPA

12.2(33)SXI2

SPA-1XTENGE-XFP

7600-SIP-600

1-port 10-Gigabit Ethernet SPA

12.2(33)SXI

XFP Modules Supported in 10-Gigabit Ethernet SPAs
XFP-10GLR-OC192LR

10-Gigabit Ethernet LR (10 km)

Gigabit Ethernet SPAs

Note Release 12.2(33)SXH and rebuilds do not support 7600-SIP-600.

 

Product ID

(append “=” for spares)

SIP Support
Product Description
Minimum
Software
Versions
SPA-10X1GE

7600-SIP-600

10-port Gigabit Ethernet SPA, SFP Optics

12.2(33)SXI

SPA-5X1GE-V2

7600-SIP-600

5-port Gigabit Ethernet SPA, SFP Optics

12.2(33)SXJ

SPA-5X1GE

7600-SIP-600

5-port Gigabit Ethernet SPA, SFP Optics

12.2(33)SXI

SPA-2X1GE-V2

7600-SIP-400

2-port Gigabit Ethernet SPA, SFP Optics, version 2

12.2(33)SXI

SPA-2X1GE

7600-SIP-400

2-port Gigabit Ethernet SPA, SFP Optics

12.2(18)SXF

SFPs Supported in Gigabit Ethernet SPAs
SFP-GE-S

Extended Temperature SX SFP

12.2(18)SXF

SFP-GE-L

Extended Temperature LX/LH SFP
SFP-GE-Z

Extended Temperature ZX SFP
SFP-GE-T

Cisco 1000BASE-T SFP (NEBS 3 ESD)

12.2(33)SXH

10/100 Mbps Ethernet SPAs

 

Product ID

(append “=” for spares)

SIP Support
Product Description
Minimum
Software
Versions
SPA-8X1FE-TX-V2

7600-SIP-200

8-port 10/100 Ethernet SPA TX

12.2(33)SXH

SPA-4X1FE-TX-V2

7600-SIP-200

4-port 10/100 Ethernet SPA TX

12.2(33)SXH

POS SPAs

Note ● Release 12.2(33)SXH and rebuilds do not support 7600-SIP-600.

  • With Release 12.2(33)SXI and later releases where CSCso97991 is not resolved, you must configure an appropriate burst size when you configure QoS policing on WAN ports. Do not rely on the burst size calculated by QoS.

 

 

Product ID

(append “=” for spares)

SIP Support
Product Description
Minimum
Software
Versions
SPA-OC192POS-VSR

7600-SIP-600

1-port OC-192c/STM-64 POS/RPR SPA, VSR-1

12.2(33)SXI

SPA-OC192POS-LR

7600-SIP-600

1-port OC-192c/STM-64 POS/RPR SPA, SM-LR

12.2(33)SXI

SPA-OC192POS-XFP

7600-SIP-600

1-port OC-192c/STM-64 POS/RPR SPA, XFP Optics

12.2(33)SXI

XFP Modules Supported in SPA-OC192POS-XFP

XFP-10GLR-OC192SR Single-Mode (SM) Short Reach (SR)

XFP-10GER-OC192IR Single-Mode (SM) Intermediate Reach (IR-2)
SPA-OC192POS-VSR

7600-SIP-600

1-port OC-192c/STM-64 POS/RPR SPA, VSR-1

12.2(33)SXI

SPA-2XOC48POS/RPR

7600-SIP-400

2-Port OC-48 POS/RPR SPA

Note Requires SFPs.

12.2(33)SXI

SPA-1XOC48POS/RPR

7600-SIP-400

1-Port OC-48 POS/RPR SPA

Note Requires SFPs.

12.2(18)SXF10

SPA-2XOC3-POS

7600-SIP-200
7600-SIP-400

2-port OC-3c/STM-1c POS SPA

Note Requires SFPs.

12.2(18)SXE

SPA-4XOC3-POS

7600-SIP-200
7600-SIP-400

4-port OC-3c/STM-1c POS SPA

Note Requires SFPs.

12.2(18)SXE

SPA-1XOC12-POS

7600-SIP-400

1-port OC-12c/STM-4c POS SPA

Note Requires an SFP.

12.2(18)SXE

ATM SPAs

Note ● Release 12.2(33)SXH and rebuilds do not support ATM SPAs.

  • With Release 12.2(33)SXI and later releases where CSCso97991 is not resolved, you must configure an appropriate burst size when you configure QoS policing on WAN ports. Do not rely on the burst size calculated by QoS.

 

 

Product ID

(append “=” for spares)

SIP Support
Product Description
Minimum
Software
Versions
SPA-1XOC12-ATM

7600-SIP-400

1-Port OC-12c/STM-4c ATM SPA

Note Requires an SFP.

12.2(18)SXE

SPA-2XOC3-ATM

7600-SIP-200
7600-SIP-400

2-port OC-3c/STM-1c ATM SPA

Note Requires SFPs.

12.2(18)SXE

SPA-4XOC3-ATM

7600-SIP-200
7600-SIP-400

4-port OC-3c/STM-1c ATM SPA

Note Requires SFPs.

12.2(18)SXE

SPA-1XOC48-ATM

7600-SIP-400

1 port OC-48c/STM-16 ATM SPA

12.2(18)SXF

SFPs for OC3 and OC12 POS and ATM SPAs

 

Product ID

(append “=” for spares)

Product Description
SFP-OC3-MM

OC-3/STM-1 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, MMF, LC connector
SFP-OC3-SR

OC-3/STM-1 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, LC connector
SFP-OC3-IR1

OC-3/STM-1 pluggable intermediate-reach (15 km) transceiver module, 1310-nm wavelength, LC connector
SFP-OC3-LR1

OC-3/STM-1 pluggable long-reach (40 km) transceiver module, 1310-nm wavelength, LC connector
SFP-OC3-LR2

OC-3/STM-1 pluggable long-reach (80 km) transceiver module, 1550-nm wavelength, LC connector
SFP-OC12-MM

OC-12/STM-4 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, MMF, LC connector
SFP-OC12-SR

OC-12/STM-4 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, LC connector
SFP-OC12-IR1

OC-12/STM-4 pluggable intermediate-reach (15 km) transceiver module, 1310-nm wavelength

SFP-OC12-LR1

OC-12/STM-4 pluggable long-reach (40 km) transceiver module, 1310-nm wavelength, LC connector
SFP-OC12-LR2

OC-12/STM-4 pluggable long-reach (80 km) transceiver module, 1550-nm wavelength, LC connector

Serial SPAs

Note With Release 12.2(33)SXI and later releases where CSCso97991 is not resolved, you must configure an appropriate burst size when you configure QoS policing on WAN ports. Do not rely on the burst size calculated by QoS.

 

Product ID

(append “=” for spares)

Product Description
SIP Support
Minimum
Software
Versions
SPA-1xCHSTM1/OC3

1-port Channelized STM1/OC3 to DS0 SPA

7600-SIP-200

12.2(33)SXH

SPA-2XCT3/DS0

2-port Channelized T3 to DS0 SPA

7600-SIP-400

12.2(33)SXI

7600-SIP-200

12.2(18)SXE

SPA-4XCT3/DS0

4-port Channelized T3 to DS0 SPA

7600-SIP-400

12.2(33)SXI

7600-SIP-200

12.2(18)SXE

SPA-8XCHT1/E1

8-Port Channelized T1/E1 SPA

7600-SIP-400

12.2(33)SXI

7600-SIP-200

12.2(18)SXE

SPA-2XT3/E3

2-port Clear Channel T3/E3 SPA

7600-SIP-400

12.2(33)SXI

7600-SIP-200

12.2(18)SXE

SPA-4XT3/E3

4-port Clear Channel T3/E3 SPA

7600-SIP-400

12.2(33)SXI

7600-SIP-200

12.2(18)SXE

Services SPA Carrier (SSC) and Services SPAs

Note If you are upgrading from a Release 12.2(18)SXF or rebuild image to a Release 12.2(33)SXH or later image, be aware of CSCsv30090, “SPA-IPsec-2G VRF: vlan 1 mistakenly trunked on upgrade from SXF to SXH.”

 

Product ID
(append “=” for spares)
Product Description
Minimum
Software
Versions
WS-SSC-600
WS-IPSEC-3

Services SPA Carrier (SSC) and IPsec SPA

With Supervisor Engine 720-10GE in VSS mode

12.2(33)SXJ1

With Supervisor Engine 720-10GE

12.2(33)SXI

With Supervisor Engine 720

With Supervisor Engine 32

7600-SSC-400
SPA-IPSEC-2G

Services SPA Carrier (SSC) and IPsec SPA

Note

  • 7600-SSC-400 does not maintain state when an NSF with SSO redundancy mode switchover occurs.
  • See the “FPD Image Packages” section for information about additional procedures required to support SPA-IPSEC-2G with Release 12.2(18)SXE and later releases.
  • SPA-IPSEC-2G does not support TACACS+ authentication for IPsec.

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXE2

With Supervisor Engine 32

12.2(18)SXF2

Enhanced FlexWAN Module

Note ● Supported only in images that contain "_wan" in the image name.

  • With Release 12.2(33)SXI and later releases where CSCso97991 is not resolved, you must configure an appropriate burst size when you configure QoS policing on WAN ports. Do not rely on the burst size calculated by QoS.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Version
WS-X6582-2PA

Enhanced FlexWAN Module; CEF256

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 32

12.2(18)SXF

Enhanced FlexWAN Module Port Adapters

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
PA-2FE

2-port Fast Ethernet Port Adapter

12.2(18)SXE

PA-1FE

1-port Fast Ethernet Port Adapter

12.2(18)SXE

PA-POS-1OC3

1-port Packet over SONET OC3c/STM1 Port Adapter

12.2(18)SXE

PA-POS-2OC3

2-port POS OC3c/STM1

  • SFPs for PA-POS-2OC3:

– SFP-OC3-MM, short range, multimode fiber

– SFP-OC3-IR1, intermediate range, single-mode fiber

– SFP-OC3-LR1, long range, single-mode fiber

12.2(17b)SXA

PA-POS-OC3MM
PA-POS-OC3SMI
PA-POS-OC3SML

Packet over SONET (OC-3)

12.2(14)SX

PA-A6-OC3MM

1-port ATM OC-3c/STM-1 multimode port adapter, enhanced

12.2(14)SX

PA-A6-OC3SMI

1-port ATM OC-3c/STM-1 single-mode (IR) port adapter, enhanced

12.2(14)SX

PA-A6-OC3SML

1-port ATM OC-3c/STM-1 single-mode (LR) port adapter, enhanced

12.2(14)SX

PA-A6-T3

1-port ATM DS3 port adapter, enhanced

12.2(14)SX

PA-A6-E3

1-port ATM E3 port adapter, enhanced

12.2(14)SX

PA-A3-OC3MM
PA-A3-OC3SMI
PA-A3-T3
PA-A3-OC3SML
PA-A3-E3
PA-A3-8T1IMA
PA-A3-8E1IMA

ATM with traffic shaping

Note These port adapters do not support LANE when installed in the FlexWAN module.

12.2(14)SX

PA-T3
PA-T3+
PA-2T3
PA-2T3+
PA-E3
PA-2E3
PA-MC-T3
PA-MC-E3
PA-MC-2T3+

T3/E3 (clear-channel and channelized)

12.2(14)SX

PA-4T+
PA-8T-V35
PA-8T-X21
PA-8T-232
PA-MC-2E1/120
PA-MC-8T1
PA-MC-8E1/120
PA-MC-2T1
PA-MC-4T1

T1/E1

12.2(14)SX

PA-4E1G/75
PA-4E1G/120

T1/E1

12.2(17)SX

PA-MC-8TE1+

Multichannel T1/E1 8PRI

Note This port adapter does not support ISDN PRI when installed in the FlexWAN module.

12.2(14)SX

PA-H
PA-2H

HSSI

12.2(14)SX

PA-MC-STM-1

Multichannel STM-1

12.2(14)SX

Service Modules

Note ● For service modules that run their own software, see the service module software release notes for information about the minimum required service module software version.

  • With SPAN configured to include a port-channel interface to support a service module, be aware of CSCth03423 and CSCsx46323.
  • EtherChannel configuration can impact some service modules. In particular, distributed EtherChannels (DECs) can interfere with service module traffic. See this field notice for more information:

http://www.cisco.com/en/US/ts/fn/610/fn61935.html

 

Application Control Engine (ACE) Module

Note ● ACE30-MOD-K9, ACE10-6500-K9, and ACE20-MOD-K9 run their own software—See these publications:

http://www.cisco.com/en/US/products/ps6906/tsd_products_support_model_home.html

See the module software release notes for information about the minimum required service module software version.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
ACE30-MOD-K9

Application Control Engine (ACE) module

With Supervisor Engine 720-10GE

12.2(33)SXI4

With Supervisor Engine 720
ACE10-6500-K9
ACE20-MOD-K9

Application Control Engine (ACE) module

Note With releases earlier than Release 12.2(33)SXI, not supported in virtual switch mode.

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXF4

Anomaly Guard Module(AGM)

Note ● WS-SVC-AGM-1-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/ps6236/tsd_products_support_model_home.html

  • See the WS-SVC-AGM-1-K9 software release notes for information about the minimum required WS-SVC-AGM-1-K9 software version.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SVC-AGM-1-K9

Anomaly Guard Module (AGM)

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH1

With Supervisor Engine 720

12.2(18)SXD3

Traffic Anomaly Detector Module (ADM)

Note ● WS-SVC-ADM-1-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/ps6236/tsd_products_support_model_home.html

  • See the WS-SVC-ADM-1-K9 software release notes for information about the minimum required WS-SVC-ADM-1-K9 software version.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SVC-ADM-1-K9

Traffic Anomaly Detector Module (ADM)

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH1

With Supervisor Engine 720

12.2(18)SXD3

ASA Services Module

Note ● Supported only with 6500 E-series chassis: WS-C6513-E, WS-C6509-V-E, WS-C6509-E, WS-C6506-E, WS-C6504-E, and WS-C6503-E.

  • Not supported in PFC3A mode.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SVC-ASA-SM1-K7

ASA Services Module

With Supervisor Engine 720-10GE

12.2(33)SXJ1

With Supervisor Engine 720
WS-SVC-ASA-SM1-K8

ASA Services Module

With Supervisor Engine 720-10GE

12.2(33)SXJ1

With Supervisor Engine 720
WS-SVC-ASA-SM1-K9

ASA Services Module

With Supervisor Engine 720-10GE

12.2(33)SXJ1

With Supervisor Engine 720

Communication Media Module (CMM)

Note ● WS-SVC-CMM runs its own software—See these publications:

http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/cmm/release/notes/OL_4847.html

  • See the WS-SVC-CMM software release notes for information about the minimum required WS-SVC-CMM software version.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SVC-CMM

Communication Media Module

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

Communication Media Module Port Adapters for WS-SVC-CMM
WS-SVC-CMM-6E1

6-Port E1 Interface Port Adapter
WS-SVC-CMM-6T1

6-Port T1 Interface Port Adapter
WS-SVC-CMM-ACT

Adhoc Conferencing and Transcoding Port Adapter
WS-SVC-CMM-24FXS

24-Port FXS Interface Port Adapter

Content Switching Module (CSM)

Note ● WS-X6066-SLB-APC runs its own software—See these publications:

http://www.cisco.com/en/US/products/hw/modules/ps2706/ps780/tsd_products_support_model_home.html

  • See the WS-X6066-SLB-APC software release notes for information about the minimum required WS-X6066-SLB-APC software version.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6066-SLB-APC

Content Switching Module (CSM)

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXI2

(Not supported in Release 12.2(33)SXJ and rebuilds)

With Supervisor Engine 720

Content Switching Module with SSL (CSM-S)

Note ● WS-X6066-SLB-S-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/hw/modules/ps2706/ps780/tsd_products_support_model_home.html

  • See the WS-X6066-SLB-S-K9 software release notes for information about the minimum required WS-X6066-SLB-S-K9 software version.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-X6066-SLB-S-K9

Content Switching Module with SSL (CSM-S)

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXI2

(Not supported in Release 12.2(33)SXJ and rebuilds)

With Supervisor Engine 720

Firewall Services Module (FWSM)

Note ● With Firewall Services Module Software Release 2.3(1) and later releases, WS-SVC-FWM-1-K9 maintains state when an NSF with SSO redundancy mode switchover occurs.

  • The FWSM runs its own software—See these publications:

http://www.cisco.com/en/US/products/hw/modules/ps2706/ps4452/tsd_products_support_model_home.html

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SVC-FWM-1-K9

Firewall Services Module; CEF256

With Supervisor Engine 720-10GE in VSS mode

12.2(33)SXI

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX1

With Supervisor Engine 32

12.2(18)SXF

Intrusion Detection System Modules (IDSMs)

Note ● The IDSM runs its own software—See these publications:

http://www.cisco.com/en/US/products/hw/modules/ps2706/ps5058/tsd_products_support_model_home.html

See the IDSM software release notes for information about the minimum required IDSM software version.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SVC-IDSM2-K9

Intrusion Detection System Module 2; CEF256

With Supervisor Engine 720-10GE in VSS mode

12.2(33)SXI

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX1

With Supervisor Engine 32

12.2(18)SXF

Network Analysis Modules (NAMs)

Note ● Network Analysis Modules run their own software—See this publication for more information:

http://www.cisco.com/en/US/products/sw/cscowork/ps5401/prod_release_notes_list.html

  • See the NAM software release notes for information about the minimum required NAM software version.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SVC-NAM3-6G-K9

Network Analysis Module 3

With Supervisor Engine 720-10GE

12.2(33)SXJ1

With Supervisor Engine 720

  • Supported only with 6500 E-series chassis: WS-C6513-E, WS-C6509-V-E, WS-C6509-E, WS-C6506-E, WS-C6504-E, and WS-C6503-E.
  • Not supported in PFC3A mode.
WS-SVC-NAM-2
WS-SVC-NAM-1

Network Analysis Module 2
Network Analysis Module 1

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX1

With Supervisor Engine 32

12.2(18)SXF

Secure Sockets Layer (SSL) Services Module

Note ● Supported in virtual switch mode.

  • WS-SVC-SSL-1 does not maintain state when an NSF with SSO redundancy mode switchover occurs.
  • WS-SVC-SSL-1 runs its own software—See the publications listed here for more information:

http://www.cisco.com/en/US/products/hw/switches/ps708/prod_release_notes_list.html

  • See the WS-SVC-SSL-1 software release notes for information about the minimum required WS-SVC-SSL-1 software version.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SVC-SSL-1

Secure Sockets Layer (SSL) Services Module

With Supervisor Engine 720-10GE

12.2(33)SXI4

  • 12.2(33)SXI4a or later recommended
  • Not supported in Release 12.2(33)SXJ and rebuilds

With Supervisor Engine 720

With Supervisor Engine 32

Wireless Services Modules

Wireless Services Module 2 (WiSM2)

Note ● Supervisor Engine 32 does not support WS-SVC-WISM2-K9.

  • In a 13-slot chassis, WS-SVC-WISM2-K9 is supported only in slots 9 through 13 and does not power up in other slots.
  • WS-SVC-WISM2-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/ps10315/prod_release_notes_list.html

  • See the WS-SVC-WISM2-K9 software release notes for information about the minimum required WS-SVC-WISM-1-K9 software version.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SVC-WISM2-K9

Wireless Services Module 2 (WiSM2)

With Supervisor Engine 720-10GE

12.2(33)SXJ

With Supervisor Engine 720

Wireless Services Module (WiSM)

Note ● With releases earlier than Release 12.2(33)SXI, not supported in virtual switch mode.

  • In a 13-slot chassis, WS-SVC-WISM-1-K9 is supported only in slots 9 through 13 and does not power up in other slots.
  • WS-SVC-WISM-1-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/ps6526/tsd_products_support_eol_model_home.html

  • See the WS-SVC-WISM-1-K9 software release notes for information about the minimum required WS-SVC-WISM-1-K9 software version.

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-SVC-WISM-1-K9

Wireless Services Module (WiSM)

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXF2

Fan Trays

Note Enter the show environment status | include fan command or the show environment cooling command to display information about the installed fan trays.

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Version
FAN-MOD-3HS

High-capacity fan tray for WS-C6503 and CISCO7603 chassis

12.2(14)SX

FAN-MOD-6HS

High-capacity fan tray for CISCO7606 chassis

12.2(14)SX

WS-C6K-6SLOT-FAN2

High-capacity fan tray for WS-C6506 chassis

12.2(14)SX

FAN-MOD-09

High-capacity fan tray for WS-C6509-NEB-A and CISCO7609 chassis

12.2(14)SX

WS-C6K-9SLOT-FAN2

High-capacity fan tray for WS-C6509 chassis

12.2(14)SX

WS-C6K-13SLT-FAN2

High-capacity fan tray for WS-C6513 and CISCO7613 chassis

12.2(14)SX

Power Supplies

CISCO7606 Power Supplies

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
PWR-2700-AC

2700 W AC power supply

12.2(18)SXE

PWR-2700-DC

2700 W DC power supply

12.2(18)SXE

WS-C6504-E and CISCO7604 Power Supplies

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
PWR-2700-AC/4

2700 W AC power supply

12.2(18)SXE

PWR-2700-DC/4

2700 W DC power supply

12.2(18)SXE

WS-C6503, WS-C6503-E, and CISCO7603 Power Supplies

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
PWR-1400-AC

1,400 W AC power supply

12.2(17a)SX

PWR-950-AC

950 W AC power supply

12.2(14)SX

PWR-950-DC

950 W DC power supply

12.2(14)SX

All Other Power Supplies

Note The power supplies in this section are not supported in these chassis:

  • Catalyst 6503
  • Catalyst 6503-E
  • CISCO7603
  • Catalyst 6504-E
  • CISCO7604

 

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-CAC-8700W-E

8,700 W AC power supply

12.2(18)SXF8

Note

  • Limited to 4,500 W inthe WS-C6509-NEB-A chassis.
  • Limited to 4,000 W in these chassis:

– WS-C6509

– WS-C6506

– WS-C6509-NEB

  • WS-CAC-8700W-E supports a remote power cycling feature.
  • See this publication for more information:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Chassis_Installation/Cat6500/6500_ins.html

PWR-6000-DC

6,000 W DC power supply

12.2(18)SXF13
12.2(33)SXH2

Note

  • Limited to 4,500 W in the WS-C6509-NEB-A chassis.
  • Limited to 4,000 W in these chassis:

– WS-C6509

– WS-C6506

– WS-C6509-NEB

WS-CAC-6000W

6,000 W AC power supply

12.2(18)SXD

Note

  • Limited to 4,500 W inthe WS-C6509-NEB-A chassis.
  • Limited to 4,000 W in these chassis:

– WS-C6509

– WS-C6506

– WS-C6509-NEB

PWR-4000-DC

4,000 W DC power supply

12.2(14)SX

WS-CAC-4000W

4,000 W AC power supply

12.2(14)SX

+WS-CAC-3000W

3,000 W AC power supply

12.2(17a)SX

Note

  • Required with Supervisor Engine 720 or Supervisor Engine 720-10GE in WS-C6509-NEB or OSR7609.
  • Included in the WS-6509-NEB-UPGRD= upgrade kit.
WS-CAC-3000W

3,000 W AC power supply

12.2(14)SX

WS-CAC-2500W

2,500 W AC power supply

12.2(14)SX

WS-CDC-2500W

2,500 W DC power supply

12.2(14)SX

Chassis

13-Slot Chassis

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-C6513-E

Catalyst 6513-E chassis:

  • 13 slots
  • 64 chassis MAC addresses
  • These modules are supported only in slots 9 through 13 and do not power up in other slots:

– WS-X6700 series switching modules except WS-X6724-SFP

– WS-X6816-GBIC switching modules

– WS-SVC-WISM-1-K9

With Supervisor Engine 720-10GE

12.2(33)SXI1
12.2(33)SXH2

With Supervisor Engine 720

12.2(33)SXI1
12.2(33)SXH2
12.2(18)SXF14

With Supervisor Engine 32

12.2(33)SXI1
12.2(33)SXH2
12.2(18)SXF14

WS-C6513

Catalyst 6513 chassis:

  • 13 slots
  • 64 chassis MAC addresses
  • Use with Supervisor Engine 720-10GE or Supervisor Engine 720 requires WS-C6K-13SLT-FAN2
  • These modules are supported only in slots 9 through 13 and do not power up in other slots:

– WS-X6700 series switching modules except WS-X6724-SFP

– WS-X6816-GBIC switching modules

– WS-SVC-WISM-1-K9

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

CISCO7613

Cisco 7613 chassis:

  • 13 slots
  • 64 chassis MAC addresses
  • Use with Supervisor Engine 720-10GE or Supervisor Engine 720 requires WS-C6K-13SLT-FAN2
  • These modules are supported only in slots 9 through 13 and do not power up in other slots:

– WS-X6700 series switching modules

– WS-X6816-GBIC switching modules

– WS-SVC-WISM-1-K9

With Supervisor Engine 720-10GE (not supported in VSS mode).

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

9-Slot Chassis

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-C6509-V-E

Catalyst 6509-V-E chassis:

  • 9 vertical slots
  • 64 chassis MAC addresses
  • Required power supply:

– 2,500 W DC or higher

– 3,000 W AC or higher

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXF10

With Supervisor Engine 32

12.2(18)SXF10

WS-C6509-E

Catalyst 6509-E chassis:

  • 9 horizontal slots
  • Chassis MAC addresses:

– Before April 2009—1024 chassis MAC addresses

– Starting in April 2009—64 chassis MAC addresses

Note Chassis with 64 MAC addresses automatically enable the Extended System ID feature, which is enabled with the spanning-tree extend system-id command. You cannot disable the extended-system ID in chassis that support 64 MAC addresses. The Extended System ID feature might already be enabled in your network, because it is required to support both extended-range VLANs and any chassis with 64 MAC addresses. Enabling the extended system ID feature for the first time updates the bridge IDs of all active STP instances, which might change the spanning tree topology.

  • Requires 2,500 W or higher power supply
  • With releases earlier than Release 12.2(18)SXD, WS-CAC-6000W is limited to 4,000 W in WS-C6509-E

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF
WS-C6509

Catalyst 6509 chassis:

  • 9 horizontal slots
  • 1024 chassis MAC addresses
  • Use with Supervisor Engine 720-10GE, Supervisor Engine 720, or Supervisor Engine 32 requires WS-C6K-9SLOT-FAN2
  • WS-CAC-6000W is limited to 4,000 W in WS-C6509

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF
WS-C6509-NEB-A

Catalyst 6509-NEB chassis

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF
WS-C6509-NEB

Catalyst 6509-NEB chassis:

  • 9 vertical slots
  • 1024 chassis MAC addresses
  • Requires the WS-6509-NEB-UPGRD= upgrade kit—refer to this publication:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16162.html

  • Does not support WS-X6716-10T-3C or WS-X6716-10T-3CXL.

With Supervisor Engine 720

12.2(17a)SX

With Supervisor Engine 32

12.2(18)SXF
CISCO7609

Cisco 7609 chassis

  • 9 vertical slots
  • 64 chassis MAC addresses

With Supervisor Engine 720-10GE (Not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF
OSR-7609

Cisco 7609 chassis:

  • 9 vertical slots
  • 1024 chassis MAC addresses
  • Requires the WS-6509-NEB-UPGRD= upgrade kit—refer to this publication:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16162.html

With Supervisor Engine 720

12.2(17a)SX

With Supervisor Engine 32

12.2(18)SXF

6-Slot Chassis

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-C6506-E

Catalyst 6506 chassis:

  • 6 slots
  • Chassis MAC addresses:

– Before April 2009—1024 chassis MAC addresses

– Starting in April 2009—64 chassis MAC addresses

Note Chassis with 64 MAC addresses automatically enable the Extended System ID feature, which is enabled with the spanning-tree extend system-id command. You cannot disable the extended-system ID in chassis that support 64 MAC addresses. The Extended System ID feature might already be enabled in your network, because it is required to support both extended-range VLANs and any chassis with 64 MAC addresses. Enabling the extended system ID feature for the first time updates the bridge IDs of all active STP instances, which might change the spanning tree topology.

  • Requires 2,500 W or higher power supply

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

WS-C6506

Catalyst 6506 chassis:

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

CISCO7606

Cisco 7606 chassis:

  • 6 slots
  • 64 chassis MAC addresses
  • Requires FAN-MOD-6HS

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

4-Slot Chassis

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-C6504-E

Catalyst 6504-E chassis:

  • 4 slots
  • 64 chassis MAC addresses

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(18)SXE

With Supervisor Engine 32

12.2(18)SXF

CISCO7604

Cisco 7604 chassis:

  • 4 slots
  • 64 chassis MAC addresses

With Supervisor Engine 720-10GE (not supported in VSS mode)

12.2(33)SXH

With Supervisor Engine 720:

12.2(18)SXE

With Supervisor Engine 32

12.2(18)SXF

3-Slot Chassis

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Versions
WS-C6503-E
  • 3 slots
  • 64 chassis MAC addresses

With Supervisor Engine 720-10GE

12.2(33)SXH

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF
WS-C6503

Catalyst 6503 chassis:

  • 3 slots
  • 64 chassis MAC addresses
  • Requires FAN-MOD-3HS
  • Does not support:

– WS-X6700 series switching modules

– WS-X6816-GBIC switching modules

– Supervisor Engine 720-10GE

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF
CISCO7603

Cisco 7603 chassis:

  • 3 slots
  • 64 chassis MAC addresses
  • Use with Supervisor Engine 720-10GE or Supervisor Engine 720 requires FAN-MOD-3HS
  • Does not support:

– WS-X6700 series switching modules

– WS-X6816-GBIC switching modules

– Supervisor Engine 720-10GE

– Supervisor Engine 32

With Supervisor Engine 720

12.2(14)SX

Cisco ME 6500 Series Ethernet Switches (ME6524)

Cisco ME 6500 Series Ethernet Switches Restrictions

Cisco ME 6500 Series Ethernet switches cannot support these software features and commands:

  • Cisco ME 6500 Series Ethernet switches are not supported in Release 12.2(33)SXJ and later releases. Support continues in Release 12.2(33)SXI and rebuilds.
  • Egress multicast replication
  • Multicast replication mode detection
  • Fabric configuration commands
  • RPR and SSO redundancy
  • VLAN translation

Cisco ME 6500 Series Ethernet Switches Features

 

Product ID

(append “=” for spares)

Product Description
Minimum
Software
Version
ME-C6524GS-8S
ME-C6524GT-8S

Cisco ME 6500 Series Ethernet switches:

  • Switch processor (SP):

– For Cisco IOS images, 256-MB DRAM ( some images require more DRAM)

– For Cisco IOS modularity images, with releases earlier than Release 12.2(33)SXH3, 256-MB DRAM ( some images require more DRAM)

– For Cisco IOS modularity images, with Release 12.2(33)SXH3 and later releases, 512-MB DRAM required ( some images require more DRAM)

– 128-MB bootflash (sup-bootflash: ; from ROMMON, it is bootflash:)

  • Route processor (RP)—Multilayer Switch Feature Card 2A (MSFC2A):

– 512-MB DRAM ( some images require more DRAM)

– 64-MB bootflash (bootflash:)

  • Policy Feature Card 3C (PFC3C)

– See the “Policy Feature Cards” section

– ME 6500 switches always operate in PFC3C mode. Enter the show platform hardware pfc mode command to display the PFC3 mode.

  • Fan tray: FAN-C6524
  • Power supplies (can be used together):

– PWR-400W-DC

– PWR-400W-AC

  • 64 chassis MAC addresses
  • One external CompactFlash Type II slot (disk0: ; supports CompactFlash Type II Flash PC cards sold by Cisco Systems, Inc., for use in Cisco ME 6500 Series Ethernet switches)
  • Eight SFP ports:

– Requires Small Form-Factor Pluggable (SFP) Modules

– 1 port group: ports 25–32

– QoS port architecture (Rx/Tx): 2q8t/1p3q8t

  • ME-C6524GS-8S:

– 24 SFP ports (requires Small Form-Factor Pluggable (SFP) Modules)

– 4 port groups: ports 1–6, 7–12, 13–18, 19–24

– QoS port architecture (Rx/Tx): 1q2t/1p3q8t

  • ME-C6524GT-8S:

– 24 10/100/1000 Mbps RJ-45 Ethernet ports

– 4 port groups: ports 1–6, 7–12, 13–18, 19–24

– QoS port architecture (Rx/Tx): 1q2t/1p3q8t

12.2(33)SXH

Note See this publication for Cisco ME 6500 Series Ethernet switch hardware information:

http://www.cisco.com/en/US/products/ps6845/tsd_products_support_eol_series_home.html

Unsupported Hardware

Note ● See the “Supervisor Engine 32 (CAT6000-SUP32/MSFC2A)” section for information about hardware that is not supported with the Supervisor Engine 32.

  • See the Release Notes for Cisco IOS Release 12.2SXF and Rebuilds publication for information about support in earlier releases:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SXF/native/release/notes/OL_4164.html

 

Release 12.2(33)SXH and later releases do not support the following hardware:

  • Supervisor Engine 1 (WS-X6K-S1A-MSFC2, WS-X6K-SUP1A-MSFC)
  • Supervisor Engine 2 (WS-X6K-S2U-MSFC2, WS-X6K-S2-MSFC2)
  • WS-F6K-DFC distributed forwarding card (DFC)
  • Optical Services Modules (OSMs)
  • These service modules:

– WS-X6381-IDS Intrusion Detection System (IDS) Module (WS-SVC-IDSM2-K9 is supported)

– WS-X6380-NAM Network Analysis Module (NAM; WS-SVC-NAM-2 and WS-SVC-NAM-1 are supported)

– WS-SVC-AON-1-K9 Application-Oriented Networking (AON) Module

– WS-SVC-CSG-1 Content Services Gateway (CSG) Module

– WS-SVC-IPSEC-1 IPsec VPN Acceleration Services Module

– WS-SVC-MWAM-1 Multi-Processor WAN Application Module

– WS-SVC-PSD-1 Persistent Storage Device Module

– WS-SVC-WEBVPN-K9 WebVPN Services Module

– WS-SVC-WLAN-1-K9 Wireless LAN service module

  • Release 12.2(33)SXI and rebuilds support the 7600-SIP-600. Release 12.2(33)SXH and rebuilds do not support the 7600-SIP-600 and these SPAs:

– SPA-10X1GE 10-port Gigabit Ethernet SPA, SFP Optics

– SPA-5X1GE 5-port Gigabit Ethernet SPA, SFP Optics

– SPA-1XTENGE-XFP 1-port 10-Gigabit Ethernet SPA, LANPHY XFP Optics

– SPA-OC192POS-VSR 1-port OC-192c/STM-64 POS/RPR SPA, VSR-1

– SPA-OC192POS-LR 1-port OC-192c/STM-64 POS/RPR SPA, SM-LR

– SPA-OC192POS-XFP 1-port OC-192c/STM-64 POS/RPR SPA, XFP Optics

– SPA-OC192POS-VSR 1-port OC-192c/STM-64 POS/RPR SPA, VSR-1

  • WS-X6182-2PA FlexWAN Module
  • These Ethernet Switching Modules:

– WS-X6024-10FL-MT 24-port 10BASE-FL MT-RJ

– WS-X6248A-TEL 48-port 10/100TX RJ-21

– WS-X6248-RJ-45 48-port 10/100TX RJ-45

– WS-X6248-TEL 48-port 10/100TX RJ-21

– WS-X6324-100FX-SM 24-port 100FX Ethernet

– WS-X6224-100FX-MT 24-port 100FX Ethernet Multimode MT-RJ

– WS-X6316-GE-TX 16-port Gigabit Ethernet RJ-45

– WS-X6416-GE-MT 16-Port Gigabit Ethernet MT-RJ

  • WS-CAC-1000W power supply
  • WS-CAC-1300W power supply
  • WS-CDC-1300W power supply
  • These fan trays:

– FAN-MOD-3

– FAN-MOD-6

– WS-C6K-6SLOT-FAN

– WS-C6509-NEB-FAN

– WS-C6K-9SLOT-FAN

– WS-C6K-13SLT-FAN

  • With a Supervisor Engine 720, WS-X6516-GBIC hardware revisions 5.0 through 5.4 with a DFC3 installed.

Supervisor Engine 720 supports a DFC3 on these WS-X6516-GBIC hardware revisions:

– Lower than 5.0

– 5.5 and higher

With a Supervisor Engine 720 and a DFC3 installed, WS-X6516-GBIC hardware revisions 5.0 through 5.3 do not power up. Without a DFC3, WS-X6516-GBIC hardware revisions 5.0 through 5.4 operate in bus mode.

See external field notice 24494 for more information:

http://www.cisco.com/en/US/ts/fn/200/fn24494.html

  • WS-X6624-FXS, WS-X6608-T1, and WS-X6608-E1 voice modules
  • WS-X6101-OC12-MMF and WS-X6101-OC12-SMF ATM LANE modules
  • WS-X6302-MSM Multilayer Switch Module
  • Catalyst 6000 series chassis

Unsupported modules remain powered down if detected and do not affect system behavior.