Service Node Group Configuration Mode Commands
To configure a WAAS Node (WNG) that is part of an AppNav Cluster, use the service-insertion service-node-group global configuration command. To unconfigure settings, use the no form of this command.
service-insertion service-node-group sngroupname{description description | service-node ip-address [description description]}
no service-insertion service-node-group sngroupname {description description | service-node ip-address [description description]}
Syntax Description
sngroupname |
Specifies the name of a WNG to configure and enters service node group configuration mode to configure WNG settings. If the WNG does not exist, this command creates it. |
description description |
(Optional) Specifies a description of the WNG with up to 200 alphanumeric and space characters. |
service-node ip-address |
Specifies the IP address of a WN to be added to the WNG. The address must be the IP address of the interface on which the WN is to receive traffic from the ANCs. |
description description |
(Optional) Specifies a description of the WN with up to 200 alphanumeric and space characters. |
Defaults
No default behavior or values.
Command Modes
global configuration
Device Modes
appnav-controller
Usage Guidelines
Use the service-insertion service-node-group command to configure a WNG that is part of an AppNav Cluster. This command initiates the service node group configuration mode, which is indicated by a different prompt (config-sng). To return to global configuration mode, enter the exit command.
Each ANC in the AppNav Cluster must be configured with the settings for each WNG in the cluster by using the service-insertion service-node-group command.
A WNG can contain a maximum of 32 WNs, with a maximum of 32 WNs across all WNGs in the AppNav Cluster.
Examples
The following example shows how to configure and enable two WNGs, each having two WNs, on a ANC:
ANC(config)# service-insertion service-node-group LondonNodeGroup
ANC(config-sng)# description London branch node group
ANC(config-sng)# service-node 10.10.10.15 description London branch node 1
ANC(config-sng)# service-node 10.10.10.16 description London branch node 2
ANC(config)# service-insertion service-node-group ChicagoNodeGroup
ANC(config-sng)# description Chicago branch node group
ANC(config-sng)# service-node 10.10.11.25 description Chicago branch node 1
ANC(config-sng)# service-node 10.10.11.26 description Chicago branch node 2
Related Commands
(config-sng) description
(config-sng) service-node
(config) service-insertion
show service-insertion
(config-sng) description
To configure the WNG description, use the description service node group configuration command. To unconfigure the description, use the no form of this command.
description description
no description description
Syntax Description
description |
Specifies a description of the WNG with up to 200 alphanumeric and space characters. |
Defaults
No default behavior or values.
Command Modes
Service node group configuration
Device Modes
appnav-controller
Examples
The following example shows how to configure a WNG description:
ANC(config)# service-insertion service-node-group LondonNodeGroup
ANC(config-sng)# description London branch node group
Related Commands
(config-sng) service-node
(config) service-insertion
show service-insertion
(config-sng) service-node
To configure the IP address and description of a WN to be added to the WNG, use the service-node service node group configuration command. To unconfigure the IP address or description, use the no form of this command.
service-node ip-address [description description]
no service-node ip-address [description description]
Syntax Description
ip-address |
Specifies the IP address of a WN to be added to the WNG. The address must be the IP address of the interface on which the WN is to receive traffic from the ANCs. |
description description |
(Optional) Specifies a description of the WN with up to 200 alphanumeric and space characters. |
Defaults
No default behavior or values.
Command Modes
Service node group configuration
Device Modes
appnav-controller
Examples
The following example shows how to configure the IP addresses of two WNs in a group:
ANC(config)# service-insertion service-node-group LondonNodeGroup
ANC(config-sng)# service-node 10.10.10.15 description London branch node 1
ANC(config-sng)# service-node 10.10.10.16 description London branch node 2
Related Commands
(config-sng) description
(config) service-insertion
show service-insertion