Cisco CMC
Commands
This chapter includes a description of all the Cisco CMC commands in alphabetical order of the command mnemonic.
For each command, this chapter provides:
-
A short description of the purpose of the command
-
The command syntax
-
The semantics of each parameter in the syntax
-
Parameter default values
-
Command example or examples
-
Related commands
The following commands are available on the Cisco CMC:
- autoboot
- bootcmc
- bootm
- enable
- exit
- fpgadnld
- help
- iminfo
- imls
- loadb
- ping
- powerreset
- power reset
- printenv
- quit
- reboot
- reset
- setenv
- show df info
- show dhcp status
- show frx
- show frx alarm
- show gcp config command stats info
- show gcp config op stats info
- show gcp config subtype stats info
- show gcp profile
- show gcp stats
- show hardware
- show hardware alarm active
- show hardware alarm history
- show hardware alarm threshold
- show igmp status
- show log file
- show onu
- show psu
- show system
- tftpboot
- unzip
- upgrade system
- version
- ?
autoboot
To auto boot the U-Boot mode on the Cisco CMC, use the autoboot command in U-Boot mode.
autoboot
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to auto boot the U-Boot mode on the Cisco CMC:
BOOT> autoboot
bootcmc
To boot the Cisco CMC using an image name, use bootcmc command in U-Boot mode.
bootcmc img_name
Syntax Description
img_name |
Name of the Cisco CMC image. |
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to boot the Cisco CMC using the image name:
BOOT> bootcmc cmc-16x4-os-1.0.bin Start tftp load cmc image to RAM addr(0xb00000)... Speed: 1000, full duplex Using eTSEC2 device TFTP from server 192.168.1.180; our IP address is 192.168.1.181 Filename 'cmc-16x4-os-1.0.bin'. Load address: 0xb00000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################## 1.5 MiB/s done Bytes transferred = 21419416 (146d598 hex) Parsed module ram address: Kernel : 0xb00054 Rootfs : 0xd786e6 DTB : 0xcf1dd2 FPGA : 0x1bf816a The image is loaded from address[0x01bf816a], with length [1]. Start unzip fpga image. Unzip from 0x1bf816a to 0x2000000 Uncompressed size: 11443612 = 0xAE9D9C start downloading address:0x2000000 .......................................................... Serial download FPGA done. PCI initializing ... PCIe1: Root Complex of mini PCIe Slot, x1, regs @ 0xffe0a000 01:00.0 - 10ee:7011 - Memory controller PCIe1: Bus 00 - 01 PCI initialization done. ## Booting kernel from Legacy Image at 00b00054 ... Image Name: Linux-3.2.0 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2039102 Bytes = 1.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00d786e6 ... Image Name: uboot ext2 ramdisk rootfs Image Type: PowerPC Linux RAMDisk Image (gzip compressed) Data Size: 15202860 Bytes = 14.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 00cf1dd2 Booting using the fdt blob at 0x00cf1dd2 Uncompressing Kernel Image ... OK Loading Ramdisk to 0efed000, end 0fe6ca2c ... OK Loading Device Tree to 03ff6000, end 03fff913 ... OK
Related Commands
Command |
Description |
---|---|
bootm |
Boots the Cisco CMC using the image from memory. |
imls |
Displays a list of all the images available in the flash memory. |
bootm
To boot the Cisco CMC using the image from memory, use the bootm command in U-Boot mode.
bootm kernel-addr rootfs-addr dtb-addr
Syntax Description
kernel-addr |
Kernel address in Random Access Memory (RAM). |
rootfs-addr |
RootFS address in RAM. |
dtb-addr |
Device tree file address in RAM. The valid values are 0xEEE00000, 0xEEE20000, and 0xEFF20000. |
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
To obtain the kernel-addr and rootfs-addr, use the imls command.
Examples
The following example shows how to boot the Cisco CMC using the image from memory:
BOOT> bootm 0xEEB00000 0xED000000 0xEEE20000 ## Booting kernel from Legacy Image at eeb00000 ... Image Name: Linux-3.2.0 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2043433 Bytes = 1.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at ed000000 ... Image Name: uboot ext2 ramdisk rootfs Image Type: PowerPC Linux RAMDisk Image (gzip compressed) Data Size: 15194591 Bytes = 14.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at eee20000 Booting using the fdt blob at 0xeee20000 Uncompressing Kernel Image ... OK Loading Ramdisk to 0efef000, end 0fe6c9df ... OK Loading Device Tree to 03ff6000, end 03fff913 ... OK
Related Commands
Command |
Description |
---|---|
bootcmc |
Boots the Cisco CMC using an image name. |
imls |
Displays a list of all the images available in the flash memory. |
enable
To enter the privilege mode, use the enable command in normal mode.
enable
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Normal (>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
Enter your password, if prompted.
Examples
The following example shows how to enter the privilege mode:
CMC> enable Please enter password: CMC#
exit
To exit the privilege mode, use the exit command.
exit
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to exit the privilege mode:
CMC# exit CMC>
fpgadnld
To download the FPGA image to the FPGA on the Cisco CMC, use fpgadnld command in U-Boot mode.
fpgadnld addr len
Syntax Description
addr |
Address of the location where the FPGA image is stored on the RAM or flash memory. |
||
len |
Length of the FPGA image.
|
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to download the FPGA image to the FPGA chip on the Cisco CMC:
BOOT> fpgadnld ee000000 1 The image is loaded from address[0xee000000], with length [1]. Start unzip fpga image. Unzip from 0xee000000 to 0x2000000 Uncompressed size: 11443612 = 0xAE9D9C start downloading address:0x2000000 .......................................................... Serial download FPGA done.
help
To display the command description and usage information, use the help command in U-Boot mode.
help
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to use the Cisco CMC command-line interface help:
BOOT> help ? - alias for 'help' autoboot- U-boot autoBoot bootcmc - start cmc image via tftp bootm - boot application image from memory fpgadnld- a tool to upgrade the FPGA help - print command description/usage iminfo - print header information for application image imls - list all images found in flash loadb - load binary file over serial line (kermit mode) ping - send ICMP ECHO_REQUEST to network host powerreset- power reset printenv- print environment variables reset - Perform RESET of the CPU setenv - set environment variables tftpboot- boot image via network using TFTP protocol unzip - unzip a memory region version - print monitor, compiler and linker version
Related Commands
Command |
Description |
---|---|
? |
Alias for help. |
iminfo
To display the header information for the Cisco CMC image, use the iminfo command in U-Boot mode.
iminfo addr
Syntax Description
addr |
Location where the header information of image must be displayed. |
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
To obtain the address or location where the header information of image must be displayed, use the imls command.
Examples
The following example shows how to display the header information for the Cisco CMC image:
BOOT> iminfo EEE40000 ## Checking Image at eee40000 ... Legacy image found Image Name: Linux-3.2.0 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2042390 Bytes = 1.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK
Related Commands
Command |
Description |
---|---|
imls |
Displays a list of all the images available in the flash memory. |
imls
To display a list of all the images available in the flash memory, use the imls command in U-Boot mode.
imls
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to display the list of available images in the flash memory:
BOOT> => imls Legacy Image at EE800000: Image Name: Linux-3.2.0 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2043433 Bytes = 1.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Legacy Image at EEB00000: Image Name: Linux-3.2.0 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2043581 Bytes = 1.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Legacy Image at EC000000: Image Name: uboot ext2 ramdisk rootfs Image Type: PowerPC Linux RAMDisk Image (gzip compressed) Data Size: 15194591 Bytes = 14.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Legacy Image at ED000000: Image Name: uboot ext2 ramdisk rootfs Image Type: PowerPC Linux RAMDisk Image (gzip compressed) Data Size: 15480455 Bytes = 14.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Legacy Image at EDF00000: Image Name: Linux-3.2.0 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2034430 Bytes = 1.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... Bad Data CRC
Related Commands
Command |
Description |
---|---|
iminfo |
Displays the header information for Cisco CMC image. |
loadb
To load a binary file to the Cisco CMC RAM via serial line using the Kermit protocol, use the loadb command in U-Boot mode.
loadb offset baud
Syntax Description
offset |
Offset address in Cisco CMC RAM where the file must be downloaded. The default value is 01000000. |
baud |
Baud rate used for transferring the file. The default value is 115200. |
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
For Cisco CMC, the baud rate must be set to 115200.
Examples
The following example shows how to load a file into the Cisco CMC RAM with Kermit protocol via serial line:
BOOT> loadb c00000 115200 ## Ready for binary (kermit) download to 0x00C00000 at 115200 bps... ## Total Size = 0x000045bf = 17855 Bytes ## Start Addr = 0x00C00000
ping
To ping an IP address, use the ping command in normal mode and U-Boot mode.
ping ip_address
Syntax Description
ip_address |
IP address. |
Command Default
None
Command Modes
Normal (>)
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
This command pings the specified IP address in the normal mode. This command sends ICMP ECHO_REQUEST to the network host in U-Boot mode.
Examples
The following example shows how to ping an IP address in normal mode:
CMC> ping 192.168.200.1 PING 192.168.200.1 (192.168.200.1): 56 data bytes 64 bytes from 192.168.200.1: icmp_seq=0 ttl=255 time=0.476 ms 64 bytes from 192.168.200.1: icmp_seq=1 ttl=255 time=0.362 ms 64 bytes from 192.168.200.1: icmp_seq=2 ttl=255 time=26.317 ms 64 bytes from 192.168.200.1: icmp_seq=3 ttl=255 time=0.450 ms 64 bytes from 192.168.200.1: icmp_seq=4 ttl=255 time=0.388 ms 64 bytes from 192.168.200.1: icmp_seq=5 ttl=255 time=0.705 ms 64 bytes from 192.168.200.1: icmp_seq=6 ttl=255 time=0.435 ms 64 bytes from 192.168.200.1: icmp_seq=7 ttl=255 time=0.433 ms 64 bytes from 192.168.200.1: icmp_seq=8 ttl=255 time=0.458 ms --- 192.168.200.1 ping statistics --- 9 packets transmitted, 9 packets received, 0% packet loss round-trip min/avg/max/stddev = 0.362/3.336/26.317/8.126 ms 0 CMC>
The following example shows how to ping an IP address in U-Boot mode:
BOOT> ping 192.168.200.4 Speed: 1000, full duplex Using eTSEC2 device host 192.168.200.4 is alive
powerreset
To power down the Cisco CMC and power it on again, use the powerreset command in U-Boot mode.
powerreset
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
This command does not power down the FRx module inside the Cisco CMC.
Examples
The following example shows how to power down and restart the Cisco CMC:
BOOT> powerreset
power reset
To power down the Cisco CMC and power it on again, use the power reset command in normal mode.
power reset
Command Default
None
Command Modes
Normal (>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
This command does not power down the FRx module inside the Cisco CMC.
Examples
The following example shows how to power down and restart the Cisco CMC:
CMC> power reset
printenv
To display the environment variables on the Cisco CMC, use the printenv command in U-Boot mode.
printenv
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to display the environment variables:
BOOT> printenv baudrate=115200 bdev=sda1 bootcmd=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate; bootm $loadaddr $ramdiskaddr $fdtaddr bootdelay=3 bootfile=uImage bypass_fpga_dnld=0 consoledev=ttyS0 eth1addr=00:04:9F:01:81:19 ethact=eTSEC2 ethaddr=00:04:9F:01:80:19 ethprime=eTSEC2 fdtaddr=0xef100000 fdtfile=p1014cmc.dtb fileaddr=1000000 filesize=AE9D9C fpga_dnld_delay=3 gatewayip=192.168.1.1 hostname=P1014CMC hwconfig=usb1:dr_mode=host,phy_type=utmi ipaddr=192.168.1.77 loadaddr=0xedf00000 netdev=eth0 netmask=255.255.255.0 othbootargs=ramdisk_size=600000 ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs; tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr ramdiskaddr=0xee200000 ramdiskfile=rootfs_image rootpath=/opt/nfsroot serverip=172.16.0.2 uboot=u-boot.bin usbext2boot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs; usb start;ext2load usb 0:4 $loadaddr $bootfile;ext2load usb 0:4 $fdtaddr $fdtfile;ext2load usb 0:4 $ramdiskaddr $ramdiskfile;bootm $loadaddr $ramdiskaddr $fdtaddr usbfatboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs; usb start;fatload usb 0:2 $loadaddr $bootfile;fatload usb 0:2 $fdtaddr $fdtfile;fatload usb 0:2 $ramdiskaddr $ramdiskfile;bootm $loadaddr $ramdiskaddr $fdtaddr Environment size: 1435/8188 bytes
Related Commands
Command |
Description |
---|---|
setenv |
Sets the environment variables. |
quit
To return to the Cisco CMC welcome interface, use the quit command in privilege mode.
quit
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to return to the Cisco CMC welcome interface:
CMC# quit Exit current session, The server is still running Welcome to CISCO CMC CMCMon login:
reboot
To restart the Cisco CMC, use the reboot command in normal mode.
reboot
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Normal (>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
The reboot command restarts the Cisco CMC without powering it down.
Examples
The following example shows how to restart the Cisco CMC:
CMC> reboot CMC# Shutting down crond services: /etc/rc.d/rcS: line 24: 3456 Terminated /etc/rc.d/init.d/$i $mode Stopping the dropbear ssh server: /etc/rc.d/rcS: line 24: 3461 Terminated /etc/rc.d/init.d/$i $mode Stopping inetd: /etc/rc.d/rcS: line 24: 3463 Terminated /etc/rc.d/init.d/$i $mode Unmounting filesystems umount: tmpfs busy - remounted read-only umount: can't remount /dev/root read-only umount: can't remount rootfs read-only mount: mounting %root% on / failed: Device or resource busy The system is going down NOW! Sent SIGTERM to all processes Sent SIGKILL to all processes Requesting system reboot Restarting system. U-Boot 0.0.5 CPU: P1014E, Version: 1.0, (0x80f90110) Core: E500, Version: 5.1, (0x80212151) Clock Configuration: CPU0:400 MHz, CCB:266.667 MHz, DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), IFC:66.667 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled Board: P1014CMC I2C: ready
reset
To reset the CPU of the Cisco CMC, use the reset command in U-Boot mode.
reset
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
This command resets the Cisco CMC without powering it down.
Examples
The following example shows how to reset the Cisco CMC CPU:
BOOT> reset
setenv
To set the environment variables on the Cisco CMC, use the setenv command in U-Boot mode.
setenv name value
Syntax Description
name |
Environment variable name. |
value |
Environment variable value. |
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to set an environment variable:
BOOT> setenv ipaddr 192.168.100.100
Related Commands
Command |
Description |
---|---|
printenv |
Displays the environment variables. |
show df info
To show system df /dev/root information, use the show df info command in privilege mode.
show df info
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.1 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
Examples
The following example shows how to display the df information:
CMC# show df info /dev/root 91691 51400 35683 59% / Wed Mar 4 02:13:48 UTC 2015 /dev/root 91691 51395 35688 59% / Wed Mar 4 02:03:48 UTC 2015 /dev/root 91691 51395 35688 59% / Wed Mar 4 01:53:48 UTC 2015 /dev/root 91691 51395 35688 59% / Wed Mar 4 01:43:48 UTC 2015 /dev/root 91691 51395 35688 59% / Wed Mar 4 01:33:48 UTC 2015 /dev/root 91691 51395 35688 59% / Wed Mar 4 01:23:48 UTC 2015
show dhcp status
To display the current Dynamic Host Configuration Protocol (DHCP) information, use the show dhcp status command in privilege mode.
show dhcp status
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to display the DHCP information for Cisco CMC:
CMC# show dhcp status ================================================================== Interface : cmc_eth0 IP_Address : 192.168.200.2 Netmask : 255.255.255.128 Default_Gateway : 192.168.200.1 DNS_Servers : None Network_Domain : cisco.com Hostname : None Lease_Time : 605400 sname : None boot_file : config_nobpib.cm CMC#
Field |
Description |
---|---|
Interface |
Name of the interface. |
IP_Address |
IP address leased from the DHCP server for the interface. |
Netmask |
Subnet mask assigned to the interface. |
Default_Gateway |
IP address of the default gateway. |
DNS_Servers |
DNS servers. |
Network_Domain |
Network domain. |
Hostname |
Name of the host. |
Lease_Time |
Time (in seconds) for which the leased IP address is valid; the duration of the lease. |
sname |
FTP or TFTP address of the server from which the image can be upgraded. |
boot_file |
Name of the image used for upgrade. |
show frx
To display information on the Forward Optical Receiver Module (FRx) installed in the Cisco CMC, use the show frx command in privilege mode.
show frx
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to display the FRx information on the Cisco CMC:
CMC# show frx ================================================================================ Controller Type : 0xbe2 PCB73PN : 73-15893-02 PCB800PN : 800-41661-01 Serial Number : 9sABCDEFGHI PID : 0 VID : V02 Hardware Version : 2.0 Software Version : FRx_0.00.06 Temperature : 0x55 Timeinservice : 5 Optical Status : 0x3 AGC Status : 0x1 Optical Input : -1600 Attenuation : 0 (0.1db) EQ : 90 (0.1db)
Field |
Description |
---|---|
Controller Type |
Controller used to identify the FRx. |
PCB73PN |
73- part number of the FRx Printed Circuit Board (PCB). |
PCB800PN |
800- part number of the FRx PCB. |
Serial Number |
Serial number of the FRx. |
PID |
Product Identifier (PID) of the FRx. |
VID |
Version Identifier (VID) of the FRx. |
Hardware Version |
Hardware version of the FRx. |
Software Version |
Software version of the FRx. |
Temperature |
Temperature of the FRx. |
Timeinservice |
Time for which the FRx is in service. |
Optical Status |
Status of the optical input power on the FRx. The value of this field can be one of the following: |
AGC Status |
Status of Automatic Gain Control (AGC) on the FRx. The value of this field can be one of the following: |
Optical Input |
Optical input power level of the FRx. |
Attenuation |
FRx attenuation value in dB. |
EQ |
FRx equalization value in dB. |
Related Commands
Command |
Description |
---|---|
show frx alarm |
Displays the FRx alarm information on the Cisco CMC. |
show frx alarm
To display alarm information for the Forward Optical Receiver Module (FRx) installed in the Cisco CMC, use the show frx alarmcommand in privilege mode.
show frx alarm
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to display the FRx alarm information on the Cisco CMC:
CMC# show frx alarm FRx: No Optical, Low Optical, AGC low ALARM raised
Related Commands
Command |
Description |
---|---|
show frx |
Displays the FRx information on the Cisco CMC. |
show gcp config command stats info
To display statistics information for the Generic Control Protocol (GCP) Exchange Data Structure (EDS) messages at command level, use the show gcp config command stats info command in privilege mode.
show gcp config command stats info
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
GCP EDS messages are classified based on commands, which are the modules, in GCP. Each command can contain many operation codes, for example, get, set, and so on. Each operation code can contain many Type Length Values (TLV).
This command displays the GCP statistics information when the Cisco CMC receives configuration commands from the Cisco CMTS.
Examples
The following example shows how to display the statistics information for GCP EDS messages at command level:
CMC# show gcp config command stats info Name Rx Tx Error ================================================================================ UEPI_PW 9 0 0 BR_ATDMA 5 5 0 BR_OFDMA 0 0 0 BND_FFT 0 0 0 OOB 0 0 0 ETHERNET_CFG 0 0 0 TOD 0 0 0 DEBUG_MISC 0 0 0 DEPI_PW 16 16 0 CFG_QAM 5 5 0 MAP_mapping 4 4 0 MISC_CFG 0 0 0 IMG_UPG 0 0 0 CMC_STATS 2 2 0 HW_FLOW_TABLE 0 0 0
Field |
Description |
---|---|
Name |
Name of the command in the GCP EDS message. |
Rx |
Number of commands received in the message. |
Tx |
Number of commands sent in the message. |
Error |
Number of errors. |
Related Commands
Command |
Description |
---|---|
show gcp config subtype stats info |
Displays statistics information for the GCP EDS messages at TLV level. |
show gcp config op stats info |
Displays statistics information for the GCP EDS messages at operation code level. |
show gcp config op stats info
To display statistics information for the Generic Control Protocol (GCP) Exchange Data Structure (EDS) messages at operation code level, use the show gcp config op stats info command in privilege mode.
show gcp config op stats info
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
GCP EDS messages are classified based on commands, which are the modules, in GCP. Each command can contain many operation codes, for example, get, set, and so on. Each operation code can contain many Type Length Values (TLV).
This command displays the GCP statistics information for the contents of the configuration commands received from the Cisco CMTS.
Examples
The following example shows how to display the EDS operation statistics information:
CMC# show gcp config op stats info Name Rx Tx Error ================================================================================ SET_DEPI_PW 16 16 0 GET_DEPI_PW 0 0 0 SET_QAM_CHAN_DISABLE 0 0 0 SET_QAM_CHAN_STARTUP 4 4 0 SET_QAM_CHAN_UPDATE 0 0 0 SET_QAM_PORT 0 0 0 GET_QAM_CHAN_CFG 0 0 0 GET_QAM_PORT 0 0 0 SET_QAM_PWR_LVL 1 1 0 SET_MAP_MAPPING 4 4 0 GET_MAP_MAPPING 0 0 0 SET_PW_TEMPLATE 1 1 0 SET_BR_PW 4 4 0 SET_BW_REQ_PW 4 4 0 SET_FFT_PW 0 0 0 SET_BND_PW 0 0 0 SET_OOB_PW 0 0 0 GET_PW_TEMPLATE_CONFIG 0 0 0 GET_BR_PW_CONFIG 0 0 0 GET_BW_REQ_PW_CONFIG 0 0 0 GET_FFT_PW_CONFIG 0 0 0 GET_BND_PW_CONFIG 0 0 0 GET_OOB_PW_CONFIG 0 0 0 SET_BR_DISABLE 3 3 0 SET_BR_STARTUP 1 1 0 SET_BR_UPDATE 0 0 0 SET_INPUT_PWR_LVL 1 1 0 SET_SID_QOS_TABLE 0 0 0 GET_BR_CONFIG 0 0 0 GET_LCH_CONFIG 0 0 0 GET_SID_QOS_TABLE 0 0 0 SET_FFT 0 0 0 SET_BND 0 0 0 SET_CMC_PWD 0 0 0 SET_CMC_TIME 0 0 0 START_IMG_UPG 0 0 0 GET_CMC_INFO 0 0 0 GET_CMC_DS_CNT 0 0 0 GET_CMC_US_UEPI_CNT 0 0 0 GET_CMC_US_DMPI_CNT 0 0 0 GET_FRx_INFO 0 0 0 SET_FRx_INFO 0 0 0 GET_CMC_CAPABILITY 2 2 0 SET_HW_FLOW_TABLE 0 0 0 GET_HW_FLOW_TABLE 0 0 0 CMC#
Field |
Description |
---|---|
Name |
Name of the operation code in the GCP EDS message. |
Rx |
Number of operation codes received in the message. |
Tx |
Number of operation codes sent in the message. |
Error |
Number of errors. |
Related Commands
Command |
Description |
---|---|
show gcp config subtype stats info |
Displays statistics information for the GCP EDS messages at TLV level. |
show gcp config command stats info |
Displays statistics information for the GCP EDS messages at command level. |
show gcp config subtype stats info
To display statistics information for the Generic Control Protocol (GCP) Exchange Data Structure (EDS) messages at Type Length Value (TLV) level, use the show gcp config subtype stats info command in privilege mode.
show gcp config subtype stats info
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
GCP EDS messages are classified based on commands, which are the modules, in GCP. Each command can contain many operation codes, for example, get, set, and so on. Each operation code can contain many TLVs.
This command displays the GCP statistics information for the previous configuration commands received from the Cisco CMTS.
Examples
The following example shows how to display the EDS subtype statistics information:
CMC# show gcp config subtype stats info Name Rx Tx Error ================================================================================ SET_DEPI_PW_CHAN_INFO 0 0 0 SET_DEPI_PW_MODE 0 0 0 SET_DEPI_PW_SESSION_ID 0 0 0 SET_DEPI_PW_DST_IP 0 0 0 SET_DEPI_PW_SRC_IP 0 0 0 SET_DEPI_PW_VLAN 0 0 0 SET_DEPI_PW_SYNC 0 0 0 SET_QAM_CHAN_INFO 0 0 0 SET_QAM_CHAN_FREQUENCY 0 0 0 SET_QAM_CHAN_POWER 0 0 0 SET_QAM_CHAN_MODULATION 0 0 0 SET_QAM_CHAN_ANNEX 0 0 0 SET_QAM_CHAN_SYMBOL_RATE 0 0 0 SET_QAM_CHAN_INTERLEAVER_DEPTH 0 0 0 SET_QAM_CHAN_RF_BLOCKING_MUTING 0 0 0 SET_QAM_PORT_EN_RF_CNT 0 0 0 SET_QAM_PORT_EN_CON_CNT 0 0 0 SET_MAP_MAPPING_CHAN_INFO 0 0 0 SET_MAP_MAPPING_ENTRY 4 4 0 UEPI_PW_MTU 8 8 0 UEPI_PW_HEADER_T 1 1 0 UEPI_PW_QOS_PSP_T 1 1 0 UEPI_PW_L2TP_SESSION 12 12 0 UEPI_PW_BW_REQ_PWID 4 4 0 UEPI_PW_BW_AGG 4 4 0 BR_ATDMA_INPUTID 0 0 0 BR_ATDMA_FREQUENCY 0 0 0 BR_ATDMA_SRATE 0 0 0 BR_ATDMA_PWR_LVL 0 0 0 BR_ATDMA_ING_CAN_EN 0 0 0 BR_ATDMA_IM_ALIGNED_FLAG 0 0 0 BR_ATDMA_ARR_MODE 0 0 0 BR_ATDMA_ARR_MODE_IUC 0 0 0 BR_ATDMA_LOGIC_CHAN 0 0 0 SET_BR_LOGIC_CHAN_BST_PRO 0 0 0 SET_BR_STARING_SID_VALUE 0 0 0 SET_BR_NUM_OF_ENTRY 0 0 0 SET_BR_CCF_QOS_BYTES 0 0 0 GET_BR_SID_VALUE 0 0 0 GET_BR_SID_ALL_VALUE 0 0 0 CMC#
Field |
Description |
---|---|
Name |
Name of the subtype at the TLV level in the GCP EDS message. |
Rx |
Number of subtypes received in the message. |
Tx |
Number of subtypes sent in the message. |
Error |
Number of errors. |
Related Commands
Command |
Description |
---|---|
show gcp config op stats info |
Displays statistics information for the GCP EDS messages at operation code level. |
show gcp config command stats info |
Displays statistics information for the GCP EDS messages at command level. |
show gcp profile
To display Generic Control Protocol (GCP) profile, use the show gcp profile command in privilege mode.
show gcp profile
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.1 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to display the gcp profile information:
CMC# show gcp profile ================================================================================ Trans-id GCP-Recv CFG_Parse GCP-Send Total 0 0.00128 0.00000 0.00080 0.03120
Field |
Description |
---|---|
Trans-id |
ID of a specific transaction. |
GCP-Recv |
The time used for receiving the GCP packet. |
CFG_Parse |
The time used for parsing the GCP packet. |
GCP-Send |
The time used for respond the GCP packet. |
Total |
The time used by the transaction. |
show gcp stats
To display the Generic Control Protocol (GCP) statistics, use the show gcp stats command in privilege mode.
show gcp stats
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
This command displays the GCP statistics information for the different types of messages received from the Cisco CMTS.
Examples
The following example shows how to display the GCP statistics:
CMC# show gcp stats info Name Rx Tx ================================================================================ Notify 0 0 GDM 3 3 EDS 52 52 EDR 0 0 MWR 0 0 ERR 0 0
Field |
Description |
---|---|
Name |
Name of the GCP EDS message. |
Rx |
Number of the received messages. |
Tx |
Number of the sent messages. |
Related Commands
Command |
Description |
---|---|
show gcp config op stats info |
Displays statistics information for the GCP EDS messages at operation code level. |
show gcp config command stats info |
Displays statistics information for the GCP EDS messages at command level. |
show gcp config subtype stats info |
Displays statistics information for the GCP EDS messages at TLV level. |
show hardware
To display the basic hardware information of the Cisco CMC, use the show hardware command in normal mode.
show hardware
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Normal (>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Cisco CMC OS 1.1 |
This command was modified. The output was modified to display the following information: |
Examples
The following example shows how to display the hardware information:
CMC> show hardware sfp: SFP 0 Information Vendor Name : N/A Vendor OUI(HEX): N/A Vendor PN : N/A Vendor SN : N/A Vendor Rev : N/A SFP 1 Information Vendor Name : N/A Vendor OUI(HEX): N/A Vendor PN : N/A Vendor SN : N/A Vendor Rev : N/A psu: PSU IDPROM Information IDPROM Version : N/A Hardware Version : N/A PCB Serial Number: N/A 73 level PN : N/A Product Number : N/A 800 level PN : N/A cpld status: CPLD SW Version: a524 CPLD HW Version: 0001 quack: EEPROM format version : 04 Compatibility byte : FF Controller Type : 0B E1 Hardware Revision : 1.0 Part Number (73) : 73-15359-1 PCB Revision : A0 Deviation Number : 0-0 Fab Version : 1 PCB Serial Number : CSJ13152101 RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 0 Part Number (800) : 800-41777-01 CLEI Code : IPUCBDVBAA Product Num/Id (PID) : DOCSIS-CMC-4P-FN Version Identifier (VID): V01 Chassis MAC Address : 00:04:9f:01:81:19 MAC Address block size : 2 CMC#
Effective with Cisco CMC OS 1.1, the output of the show hardware command was modified to display the vendor CPN, VID, and PID information:
CMC# show hardware sfp: SFP 0 Information Vendor Name : CISCO Vendor OUI(HEX): 009065 Vendor PN : FTRJ8519P1BNL-C6 Vendor SN : Fyuy1089E2YR Vendor Rev : A Vendor CPN : 10-2143-01 Vendor VID : V01 Vendor PID : SFP-GE-S SFP1 is not present psu: PSU IDPROM Information Hardware Version : 3.0 73 level PN : 74-15360-02 PCB Revision : 02 Deviation Number : 0-0 PCB Fab Version : 0 PCB Serial Number : CAT1825E269 800 Level PN : 800-41662-02
Field |
Description |
---|---|
sfp |
SFP information. |
Vendor Name |
Name of the vendor. |
Vendor OUI(HEX) |
Organizationally Unique Identifier (OUI) of the vendor. |
Vendor PN |
Part number for the vendor. |
Vendor SN |
Serial number for the vendor. |
Vendor Rev |
Revision number for the vendor. |
Vendor CPN |
Cisco part number for the vendor. |
Vendor VID |
Version identification for the vendor. |
Vendor PID |
Product number for the vendor. |
psu |
Power Supply Unit (PSU) information. |
PSU IDPROM Information |
IDPROM information of the PSU. |
IDPROM Version |
Version number of the IDPROM. |
Hardware Version |
Version number of the PSU hardware. |
PCB Serial Number |
Serial number of the PSU Printed Circuit Board (PCB). |
73 level PN |
73- part number of the PSU. |
Product Number |
Product number of the PSU. |
800 level PN |
800- part number of the PSU. |
cpld status |
Status of the Complex Programmable Logic Device (CPLD). |
CPLD SW Version |
Version of the CPLD software. |
CPLD HW Version |
Version of the CPLD hardware. |
quack |
Quack information. |
EEPROM format version |
Version of the EEPROM format. |
Compatibility byte |
Downward compatibility information. |
Controller Type |
Controller used to identify the Cisco CMC. |
Hardware Revision |
Revision number of the Cisco CMC hardware. |
Part Number (73) |
73- part number of the Cisco CMC. |
PCB Revision |
Revision number of the Cisco CMC PCB. |
Deviation Number |
Revision number (signifying a minor deviation) of the Cisco CMC. |
Fab Version |
Fabrication version of the Cisco CMC. |
PCB Serial Number |
Serial number of the Cisco CMC PCB. |
RMA Test History |
Counter indicating the number of times the Cisco CMC has been returned and repaired. |
RMA Number |
Return Material Authorization (RMA) number, which is an administrative number assigned if the Cisco CMC needs to be returned for repair. |
RMA History |
Counter indicating the number of times the Cisco CMC has been returned and repaired. |
Part Number (800) |
800- part number of the Cisco CMC. |
CLEI Code |
Common Language Equipment Identification (CLEI) number. |
Product Num/Id (PID) |
PID of the Cisco CMC. |
Version Identifier (VID) |
VID of the Cisco CMC. |
Chassis MAC Address |
MAC address of the Cisco CMC. |
MAC Address block size |
Block size of the MAC address. |
Related Commands
Command |
Description |
---|---|
show hardware alarm active |
Displays the current alarm information on the Cisco CMC. |
show hardware alarm history |
Displays information on the history of all alarms the Cisco CMC. |
show hardware alarm threshold |
Displays the hardware alarm threshold of the Cisco CMC. |
show hardware alarm active
To display the current information of the hardware sensor monitors on the Cisco CMC, use the show hardware alarm active in privilege mode.
show hardware alarm active
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
This command displays the current values and status of the hardware sensors monitors.
Examples
The following example shows how to display the information on current alarms:
CMC# show hardware alarm active Name Type Unit Value Status ================================================================================ VP3P3_UPX_MON voltage V 3.308 normal VP12P0_IN_MON voltage V 12.127 normal VP5P0_MON voltage V 4.966 normal VP3P3_MON voltage V 3.288 normal VP5P0_UPX_MON voltage V 4.967 normal VP1P8_MON voltage V 1.784 normal VP1P0_CPU_MON voltage V 0.997 normal VP0P75_VTT2_MON voltage V 0.746 normal VP3P3_CLK_MON voltage V 3.307 normal VP12P0_UPX_MON voltage V 11.681 normal PSU_MON voltage V 0.000 N/A VP1P8_UPX_MON voltage V 1.808 normal VP2P5_US_MON voltage V 2.503 normal VP3P6_MON voltage V 3.577 normal VN1P5_MON voltage V -1.516 normal VP1P9_MON voltage V 1.901 normal VP2P5_MON voltage V 2.512 normal VP1P0_MON voltage V 0.994 normal VP1P2_MON voltage V 1.199 normal VP1P5_MON voltage V 1.507 normal Clock temperature C 36.000 normal DAC temperature C 40.000 normal Local temperature C 37.000 normal FPGA temperature C 82.000 normal CPU temperature C 40.000 normal PA temperature C 48.000 normal SFP temperature C 26.500 normal CURROUT_VP1P2 current A 0.385 normal CURROUT_VP1P0 current A 0.746 normal CURROUT_VP1P5 current A 0.109 normal CURROUT_VP1P8 current A 0.185 normal CURROUT_VP2P5 current A 0.297 normal CURROUT_VP3P6 current A 0.343 normal CURROUT_VP5P4 current A 0.174 normal CMC#
Field |
Description |
---|---|
Name |
Name of the hardware sensor monitor. |
Type |
Type of the hardware sensor monitor. The type can be voltage, current, or temperature. |
Unit |
Unit used for monitoring the hardware sensor. |
Value |
Current value of the hardware sensor monitor. |
Status |
Status of the hardware sensor monitor. |
Related Commands
Command |
Description |
---|---|
show hardware |
Displays the basic hardware information of the Cisco CMC. |
show hardware alarm history |
Displays information on the history of all alarms Cisco CMC. |
show hardware alarm threshold |
Displays the hardware alarm threshold of the Cisco CMC. |
show hardware alarm history
To display information on the history of the hardware sensor monitors on the Cisco CMC, use the show hardware alarm history command in privilege mode.
show hardware alarm history
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
This command displays the history of values and status of the hardware sensor monitors.
Examples
The following example shows how to display the history of values and status of hardware sensor monitors on the Cisco CMC:
CMC# show hardware alarm history Index Name Type Unit Value Status Time -------------------------------------------------------------------------------- 1 VP1P5_MON voltage V 1.507 normal 1970-01-01 00:05:36 2 VP1P2_MON voltage V 1.199 normal 1970-01-01 00:05:36 3 CURROUT_VP5P4 current A 0.174 normal 1970-01-01 00:05:36 4 SFP temperature C 26.500 normal 1970-01-01 00:05:36 5 VP1P0_MON voltage V 0.994 normal 1970-01-01 00:05:36 6 VP2P5_MON voltage V 2.512 normal 1970-01-01 00:05:35 7 VP1P9_MON voltage V 1.901 normal 1970-01-01 00:05:35 8 VN1P5_MON voltage V -1.516 normal 1970-01-01 00:05:35 9 VP3P6_MON voltage V 3.577 normal 1970-01-01 00:05:35 10 VP2P5_US_MON voltage V 2.503 normal 1970-01-01 00:05:35 11 VP1P8_UPX_MON voltage V 1.808 normal 1970-01-01 00:05:34 12 PSU_MON voltage V 0.000 N/A 1970-01-01 00:05:34 13 VP12P0_UPX_MON voltage V 11.681 normal 1970-01-01 00:05:34 14 VP3P3_CLK_MON voltage V 3.307 normal 1970-01-01 00:05:34 15 VP0P75_VTT2_MON voltage V 0.746 normal 1970-01-01 00:05:34 16 VP1P0_CPU_MON voltage V 0.997 normal 1970-01-01 00:05:33 17 VP1P8_MON voltage V 1.784 normal 1970-01-01 00:05:33 18 PA temperature C 48.000 normal 1970-01-01 00:05:33 19 CPU temperature C 40.000 normal 1970-01-01 00:05:33 20 VP5P0_UPX_MON voltage V 4.967 normal 1970-01-01 00:05:33 21 CURROUT_VP3P6 current A 0.343 normal 1970-01-01 00:05:33 22 FPGA temperature C 82.000 normal 1970-01-01 00:05:33 23 CURROUT_VP2P5 current A 0.297 normal 1970-01-01 00:05:33 24 Local temperature C 37.000 normal 1970-01-01 00:05:33 25 CURROUT_VP1P8 current A 0.185 normal 1970-01-01 00:05:33 26 CURROUT_VP1P5 current A 0.109 normal 1970-01-01 00:05:33 27 DAC temperature C 40.000 normal 1970-01-01 00:05:33 28 CURROUT_VP1P0 current A 0.746 normal 1970-01-01 00:05:33 29 CURROUT_VP1P2 current A 0.385 normal 1970-01-01 00:05:33 30 VP3P3_MON voltage V 3.288 normal 1970-01-01 00:05:33 31 VP5P0_MON voltage V 4.966 normal 1970-01-01 00:05:32 32 Clock temperature C 36.000 normal 1970-01-01 00:05:32 33 VP12P0_IN_MON voltage V 12.127 normal 1970-01-01 00:05:32 34 VP3P3_UPX_MON voltage V 3.308 normal 1970-01-01 00:05:32 -------------------------------------------------------------------------------- 35 VP1P5_MON voltage V 1.506 normal 1970-01-01 00:00:32 36 VP1P2_MON voltage V 1.199 normal 1970-01-01 00:00:31 37 CURROUT_VP5P4 current A 0.172 normal 1970-01-01 00:00:31 38 SFP temperature C 26.500 normal 1970-01-01 00:00:31 39 VP1P0_MON voltage V 0.998 normal 1970-01-01 00:00:31 40 VP2P5_MON voltage V 2.513 normal 1970-01-01 00:00:31 41 VP1P9_MON voltage V 1.901 normal 1970-01-01 00:00:31 42 VN1P5_MON voltage V -1.505 normal 1970-01-01 00:00:31 43 VP3P6_MON voltage V 3.577 normal 1970-01-01 00:00:30 44 VP2P5_US_MON voltage V 2.503 normal 1970-01-01 00:00:30 45 VP1P8_UPX_MON voltage V 1.809 normal 1970-01-01 00:00:30 46 PSU_MON voltage V 0.000 N/A 1970-01-01 00:00:30 47 VP12P0_UPX_MON voltage V 11.748 normal 1970-01-01 00:00:30 48 VP3P3_CLK_MON voltage V 3.307 normal 1970-01-01 00:00:29 49 VP0P75_VTT2_MON voltage V 0.745 normal 1970-01-01 00:00:29 50 VP1P0_CPU_MON voltage V 0.997 normal 1970-01-01 00:00:29 51 VP1P8_MON voltage V 1.785 normal 1970-01-01 00:00:29 52 PA temperature C 45.000 normal 1970-01-01 00:00:29 53 CPU temperature C 36.000 normal 1970-01-01 00:00:29 54 VP5P0_UPX_MON voltage V 4.967 normal 1970-01-01 00:00:29 55 CURROUT_VP3P6 current A 0.342 normal 1970-01-01 00:00:28 56 FPGA temperature C 55.000 normal 1970-01-01 00:00:28 57 CURROUT_VP2P5 current A 0.250 normal 1970-01-01 00:00:28 58 Local temperature C 32.000 normal 1970-01-01 00:00:28 59 CURROUT_VP1P8 current A 0.169 normal 1970-01-01 00:00:28 60 CURROUT_VP1P5 current A 0.113 normal 1970-01-01 00:00:28 61 DAC temperature C 35.000 normal 1970-01-01 00:00:28 62 CURROUT_VP1P0 current A 0.443 normal 1970-01-01 00:00:28 63 CURROUT_VP1P2 current A 0.385 normal 1970-01-01 00:00:28 64 VP3P3_MON voltage V 3.287 normal 1970-01-01 00:00:28 65 VP5P0_MON voltage V 4.966 normal 1970-01-01 00:00:28 66 Clock temperature C 34.000 normal 1970-01-01 00:00:28 67 VP12P0_IN_MON voltage V 12.239 normal 1970-01-01 00:00:28 68 VP3P3_UPX_MON voltage V 3.309 normal 1970-01-01 00:00:28 --------------------------------------------------------------------------------
Field |
Description |
---|---|
Index |
Index of the hardware sensor monitor. |
Name |
Name of the hardware sensor monitor. |
Type |
Type of the hardware sensor monitor. The type can be voltage, current, or temperature. |
Unit |
Unit used for monitoring the hardware sensor. |
Value |
Previous value of the hardware sensor monitor. |
Status |
Status of the hardware sensor monitor. |
Time |
Time at which the hardware sensor was monitored. |
Related Commands
Command |
Description |
---|---|
show hardware |
Displays the basic hardware information of the Cisco CMC. |
show hardware alarm active |
Displays the current alarm information of the Cisco CMC. |
show hardware alarm threshold |
Displays the hardware alarm threshold of the Cisco CMC. |
show hardware alarm threshold
To display the alarm threshold information for the hardware sensor monitors on the Cisco CMC, use the show hardware alarm threshold command in privilege mode.
show hardware alarm threshold
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
This command displays the threshold values for the hardware sensor monitors.
Examples
The following example shows how to display the hardware alarm threshold for the Cisco CMC:
CMC# show hardware alarm threshold Name Type Unit Min- Low- High- Max- threshold threshold threshold threshold ================================================================================ VP3P3_UPX_MON voltage V 3.000 3.100 3.450 3.600 VP12P0_IN_MON voltage V 11.800 12.000 13.300 14.000 VP5P0_MON voltage V 4.600 4.750 5.300 5.400 VP3P3_MON voltage V 3.000 3.100 3.450 3.600 VP5P0_UPX_MON voltage V 4.500 4.750 5.300 5.500 VP1P8_MON voltage V 1.650 1.750 1.850 1.950 VP1P0_CPU_MON voltage V 0.900 0.950 1.100 1.200 VP0P75_VTT2_MON voltage V 0.680 0.710 0.790 0.830 VP3P3_CLK_MON voltage V 3.000 3.100 3.500 3.600 VP12P0_UPX_MON voltage V 11.000 11.300 12.500 13.000 PSU_MON voltage V 20.000 22.000 92.000 94.000 VP1P8_UPX_MON voltage V 1.640 1.700 1.900 1.950 VP2P5_US_MON voltage V 2.300 2.350 2.650 2.700 VP3P6_MON voltage V 3.250 3.400 3.800 3.900 VN1P5_MON voltage V -1.600 -1.570 -1.430 -1.400 VP1P9_MON voltage V 1.750 1.800 2.000 2.050 VP2P5_MON voltage V 2.300 2.400 2.650 2.750 VP1P0_MON voltage V 0.900 0.950 1.100 1.200 VP1P2_MON voltage V 1.100 1.150 1.250 1.300 VP1P5_MON voltage V 1.350 1.400 1.600 1.650 Clock temperature C -40.000 -25.000 95.000 100.000 DAC temperature C -40.000 -25.000 92.000 100.000 Local temperature C -40.000 -25.000 95.000 100.000 FPGA temperature C -40.000 -25.000 95.000 100.000 CPU temperature C -40.000 -25.000 94.000 98.000 PA temperature C -40.000 -25.000 92.000 100.000 SFP temperature C -40.000 -25.000 95.000 100.000 CURROUT_VP1P2 current A 0.000 0.000 0.508 1.129 CURROUT_VP1P0 current A 0.000 0.000 0.940 1.223 CURROUT_VP1P5 current A 0.000 0.000 0.141 1.129 CURROUT_VP1P8 current A 0.000 0.000 0.254 1.016 CURROUT_VP2P5 current A 0.000 0.000 0.352 1.411 CURROUT_VP3P6 current A 0.000 0.000 0.508 1.694 CURROUT_VP5P4 current A 0.000 0.000 0.508 2.541 CMC#
Field |
Description |
---|---|
Name |
Name of the hardware sensor monitor. |
Type |
Type of the hardware sensor monitor. The type can be voltage, current, or temperature. |
Unit |
Unit used for monitoring the hardware sensor. |
Min-threshold |
Minimum threshold value of the hardware sensor monitor. |
Low-threshold |
Low threshold value of the hardware sensor monitor. |
High-threshold |
High threshold value of the hardware sensor monitor. |
Max-threshold |
Maximum threshold value of the hardware sensor monitor. |
Related Commands
Command |
Description |
---|---|
show hardware |
Displays the basic hardware information of the Cisco CMC. |
show hardware alarm active |
Displays the current alarm information on the Cisco CMC. |
show hardware alarm history |
Displays information on the history of all alarms on the Cisco CMC. |
show igmp status
To display the current Internet Group Management Protocol (IGMP) status, use the show igmp status command in privilege mode.
show igmp status
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to display the current IGMP status on the Cisco CMC:
CMC# show igmp status Channel Status Group Port Interface Link-status ================================================================================ 0 success 225.1.1.1 0 cmc_eth0 1(connected) 1 success 225.1.1.2 0 cmc_eth0 1(connected) 2 success 225.1.1.3 0 cmc_eth0 1(connected) 3 success 225.1.1.4 0 cmc_eth0 1(connected) 4 success 226.10.10.10 0 cmc_eth0 1(connected)
Field |
Description |
---|---|
Channel |
Downstream channel number. |
Status |
Status of the IGMP join. |
Group |
Multicast or broadcast address. |
Port |
Port used by the Cisco CMTS router. |
Interface |
Interface used by the Cisco CMTS router. |
Link-status |
Status of the link. |
show log file
To display the Cisco CMC error log files, use the show log file command in privilege mode.
show log file file-index
Syntax Description
file-index |
File index number. The valid range is from 0 to 4. |
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
The error logs are stored in five files, and the lowest file index number contains the latest error log information.
Examples
The following example shows how to display the log file details for file index number 1:
CMC# show log file 0 1970-01-01 00:03:22,912 - ERROR - CMC IF Mon/DHCP Module suffers from DHCP:Cannot get the IP address from CMTS, reboot... 1970-01-01 00:03:22,145 - ERROR - CMC IF Mon/DHCP Module suffers from DHCP:Cannot get the IP address from CMTS, reboot... 1970-01-01 00:01:38,238 - ERROR - CMC GCP Module suffers from CMC will be rebooted... 1970-01-01 00:01:38,163 - ERROR - CMC GCP Module suffers from Rebooting the CMC... 1970-01-01 00:01:38,089 - ERROR - CMC GCP Module suffers from CMTS connection [192.168.200.129, 6010] is lost 1970-01-01 00:00:34,518 - ERROR - CMC Management Module suffers from Cannot get the DHCP offer in 10s, retrying... 1970-01-01 00:05:09,402 - ERROR - CMC GCP Module suffers from CMTS connection [192.168.200.129, 6010] is lost /usr/bin/cmcapp-1.0/cmc_cli_adapter/cmc_cli_adapter.py##423##client_unregister_handler /usr/bin/cmcapp-1.0/cmc_cli_adapter/cmc_cli_adapter.py##548##parse_posix_message /usr/bin/cmcapp-1.0/cmc_cli_adapter/cmc_cli_adapter.py##630##run /usr/lib/python2.7/threading.py##551##__bootstrap_inner /usr/lib/python2.7/threading.py##524##__bootstrap --More-- (0% of 630884 bytes)
show onu
To display the Optical Network Unit (ONU) information, use the show onu command in normal mode.
show onu
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Normal (>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to display the ONU information:
CMC> show onu ONU0: TX Power : 0(0.1uW) RX Power : 0(0.1uW) Link Status : 0 MAC address : 00:23:c0:06:5c:90 ONU1: TX Power : 0(0.1uW) RX Power : 5(0.1uW) Link Status : 0 MAC address : 20:00:7f:58:00:00
Field |
Description |
---|---|
TX Power |
Power transmitted from the ONU, in 0.1uW. |
RX Power |
Power received at the ONU, in 0.1uW. |
Link Status |
Link status of the ONU. The value of this field can be one of the following: |
MAC address |
MAC address of the ONU. |
show psu
To display the Power Supply Unit (PSU) information, use the show psu command in privilege mode.
show psu
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to display the PSU status on the Cisco CMC:
CMC# show psu ================================================================================ PSU = 60.000 Vac CMC#
Field |
Description |
---|---|
PSU |
Value of the PSU. |
show system
To display the basic system information of the Cisco CMC, use the show system command in normal mode.
show system
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Normal (>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
This command displays the basic system information of the Cisco CMC, including Product Identifier (PID), Serial Number (SN), MAC address, software image version, ROMMON version, FRx firmware version, reset reason, boot flags, and so on.
Examples
The following example shows how to display the basic system information on the Cisco CMC:
CMC> show system PID : DOCSIS-CMC-4P-FN SN : CSJ13152101 MAC : 00:02:3d:fe:fe:01 new image : 1.0(May 15 16:57:09 CST 2014) old image : 20140515(May 09 14:30:15 CST 2014) running version : 1.0(May 15 16:57:09 CST 2014) new image location : bank 2 boot error indication : NO remaining reboot count : 2 rommon version : 0.0.8 FRx Version : N/A CMC reset reason : Power on
Field |
Description |
---|---|
PID |
Product Identifier (PID) of the Cisco CMC. |
SN |
Serial number of the Cisco CMC. |
MAC |
MAC address of the Cisco CMC. |
new image |
Version of the new image version available on the Cisco CMC. |
old image |
Version of the old image on the Cisco CMC. |
running version |
Version of the image currently running on the Cisco CMC. |
new image location |
Bank (bank 1 or bank 2) in which the new image is located. |
boot error indication |
Indicates if there are errors during the reboot. |
remaining reboot count |
Counter indicating the number of remaining reboots after which the Cisco CMC boots with an image on the other bank. |
rommon version |
ROMMON version of the Cisco CMC. |
FRx version |
Firmware version of the FRx used in the Cisco CMC. |
CMC reset reason |
Reason for the previous reset of the Cisco CMC. |
tftpboot
To boot the Cisco CMC with an image via network using TFTP, use the tftpboot command in U-Boot mode.
tftpboot address filename
Syntax Description
address |
RAM address. The default RAM address is 0xedf00000. |
||
filename |
Name of the image. For the first power on, the default image name is uImage.
|
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
This command downloads the image through TFTP to the Cisco CMC RAM.
Examples
The following example shows how to boot the Cisco CMC using an image via network using the TFTP :
BOOT> tftpboot 1000000 p1014cmc.dtb Speed: 1000, full duplex Using eTSEC2 device TFTP from server 192.168.100.180; our IP address is 192.168.100.100 Filename 'p1014cmc.dtb'. Load address: 0x1000000 Loading: ###### 435.5 KiB/s done Bytes transferred = 26788 (68a4 hex)
unzip
To unzip a memory region, use the unzip command in U-Boot mode.
unzip srcaddr dstaddr
Syntax Description
srcaddr |
Location of the zip file. The valid values are 0xEE000000 and 0xEE400000. |
dstaddr |
Location where the file is placed after unzip. The valid value is 0x01400000. |
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Examples
The following example shows how to unzip a memory region:
BOOT> unzip 0xEE400000 0x01400000 Uncompressed size: 11443612 = 0xAE9D9C
upgrade system
To upgrade the Cisco CMC image by specifying the URL, use the upgrade system command in privilege mode.
upgrade system url
Syntax Description
url |
Firmware URL where the image is available. |
Command Default
None
Command Modes
Privilege (#)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
Cisco CMC supports FTP and TFTP for image upgrade. The URL can be in one of the following formats:
Note | The URL is case-sensitive. |
Examples
The following example shows how to upgrade the Cisco CMC version:
CMC# upgrade system tftp://192.168.1.1/image-1.1.bin Downloading the firmware… Start to upgrade the CMC system... !!!start upgrading firmware!!! DO NOT power off until upgraded successfully! Verify new package ... Magic Number is OK! Attention: CMC System Upgrade has Started. Verify Checksum Succeed! DTB, FPGA, KERNEL, ROOTFS are all included in package. Check if same with running package ... Running version: 0.25 => New version: 0.26 Upgrade Partition: 2 Linux rootfs upgrading... Magic Number is OK! Verify Checksum Succeed! Pick Up File: rootfs_tmp Succeed! Flash rootfs image to mtd1 Erasing blocks: 116/116 (100%) Writing data: 14844k/14844k (100%) Verifying data: 14844k/14844k (100%) Extract build date time from rootfs file... Extracted build time: May 09 14:58:24 CST 2014 . . .
version
To display the monitor, compiler, and linker version information for the Cisco CMC, use the version command in U-Boot mode.
version
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
This command displays the U-Boot version used in Cisco CMC.
Examples
The following example shows how to display the monitor, compiler, and linker version information on the Cisco CMC:
BOOT> version U-Boot 0.0.5 (Apr 11 2014 - 09:47:10) powerpc-none-linux-gnuspe-gcc (GCC) 4.3.2 GNU Id (GNU Binutils) 2.18.50.20080215
?
To display the help information, use the ? command in U-Boot mode.
?
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
U-Boot (BOOT>)
Command History
Release | Modification |
---|---|
Cisco CMC OS 1.0 |
This command was introduced on the Cisco CMC. |
Usage Guidelines
The ? command is an alias for the help command.
Examples
The following example shows how to display the help information in U-Boot mode:
BOOT> ? ? - alias for 'help' autoboot- U-boot autoBoot bootcmc - start cmc image via tftp bootm - boot application image from memory fpgadnld- a tool to upgrade the FPGA help - print command description/usage iminfo - print header information for application image imls - list all images found in flash loadb - load binary file over serial line (kermit mode) ping - send ICMP ECHO_REQUEST to network host powerreset- power reset printenv- print environment variables reset - Perform RESET of the CPU setenv - set environment variables tftpboot- boot image via network using TFTP protocol unzip - unzip a memory region version - print monitor, compiler and linker version