Upgrading to Cisco Remote PHY Shelf 7200 Software 1.2
Upgrading Cisco Remote PHY Shelf 7200 and cBR-8 Router
Before you begin
Before upgrading the system, make sure the following requirements are met:
-
All eRPDs are online.
-
Download two files from the following Cisco.com Software Center URL:
https://software.cisco.com/download/type.html?mdfid=286283913&flowid=73842
-
IOS XE Software Version 16.10.1f: cbrsup-universalk9.16.10.01f.SPA.bin
-
Cisco Remote PHY Shelf 7200 1.2: HA-SHELF-V1-2.itb.rel.sign
-
-
Console access for both SUPs are required.
Note |
For more information about upgrading the cBR-8 router, see https://www.cisco.com/c/en/us/td/docs/cable/cbr/upgrade/guide/b_cbr_upgrade_16_10.html. |
Procedure
Step 1 |
Copy Cisco IOS-XE Fuji 16.10.1f package to bootflash: and stby-bootflash:.
|
||
Step 2 |
Verify Cisco IOS-XE Fuji 16.10.1d package against the md5 hash as provided in the Cisco.com Software center.
|
||
Step 3 |
Backup current running config to bootflash:.
|
||
Step 4 |
Check system status prior to upgrade. Save the information to compare against the system status after upgrade. For the commands to use to check the status, see the show commands at the end of this section.
|
||
Step 5 |
Copy Cisco HA-SHELF-V1-2 image package to HTTP or TFTP server that RPDs can reach to. |
||
Step 6 |
Verify current RPHY Shelf 7200 software version.
|
||
Step 7 |
Upgrade one or more RPHY Shelf image to V1.2 from cBR-8. To upgrade one RPHY Shelf image using HTTP server, run this command:
To upgrade one RPHY Shelf image using TFTP server, run this command:
To upgrade all RPHY Shelf images using HTTP server, run this command
To upgrade all RPHY Shelf images using TFTP server, run this command
|
||
Step 8 |
Verify one or more RPHY Shelf 7200 chassis status. To verify one RPHY Shelf 7200 chassis status, run this command.
To verify all RPHY Shelf 7200 chassis status, run this command.
|
||
Step 9 |
Configure the chassis to boot the system with Cisco IOS-XE Fuji 16.10.1f image and save running-configuration.
|
||
Step 10 |
Reload and bring up the cBR-8 router.
|
||
Step 11 |
Adjust RPHY Shelf 7200 max-carrier and type, re-apply rpd-ds base-power for each RPHY Shelf 7200, save and backup current running-config.
|
||
Step 12 |
To check if all RPHY Shelf 7200 chassis have been upgraded to new version 1.2 and come online succesfully you can either: Telnet to FCC IP and run the show version command or To check if one or more RPHY Shelf 7200 chassis have been upgraded, SSH to the eRPD and run the show version command. |
What to do next
These show commands may be useful in the verification test:
-
select erpd slot slot_id index index_id — RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
-
select linecard slot slot_id — RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
-
show version— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show platform— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show platform diag— Supported on cBR-8 and RPHY Shelf 7200
-
show environment— Supported on cBR-8
-
show environment all | alarms— Supported on RPHY Shelf 7200
-
show environment power— Supported on cBR-8
-
show platform hardware slot P <0-5> mcu status— Supported on cBR-8
-
show facility-alarm status — Supported on cBR-8
-
show redundancy— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show redundancy line card all— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show ip ospf neighbor— Supported on cBR-8
-
show cable modem voice— Supported on cBR-8
-
show cable calls— Supported on cBR-8
-
show cable licenses all— Supported on cBR-8
-
show inventory— Supported on cBR-8
-
show log — Supported on cBR-8 and RPHY Shelf 7200 with different outputs
-
show cable rpd— Supported on cBR-8
-
show cable modem summary total— Supported on cBR-8
-
show cable rpd lcha— Supported on cBR-8
-
show running— Supported on cBR-8 and RPHY Shelf 7200 with different outputs
-
show tech— Supported on cBR-8 and RPHY Shelf 7200 with different outputs
Upgrading Cisco Remote PHY Shelf 7200 Only
Before you begin
Before upgrading the system, make sure the following requirements are met:
-
All eRPDs are in init(gcp), init(clock), or online state.
-
Download new image file from the following Cisco.com Software Center URL:
https://software.cisco.com/download/type.html?mdfid=286283913&flowid=73842
-
Cisco Remote PHY Shelf 7200 1.2: HA-SHELF-V1-2.itb.rel.sign
-
Note |
For more information about upgrading the cBR-8 router, see https://www.cisco.com/c/en/us/td/docs/cable/cbr/upgrade/guide/b_cbr_upgrade_16_10.html. |
Note |
Cisco recommends that to upgrade only Cisco Remote PHY Shelf 7200, you must run all commands on the Cisco Remote PHY Shelf 7200. |
Procedure
Step 1 |
Copy the Cisco RPHY Shelf 7200 V1.2 image package to HTTP or TFTP server that RPDs can reach to.
|
||
Step 2 |
Verify current RPHY Shelf 7200 software version.
|
||
Step 3 |
Upgrade one or more RPHY Shelf image to V1.2 from cBR-8. To upgrade one RPHY Shelf image using HTTP server, run this command:
To upgrade one RPHY Shelf image using TFTP server, run this command:
To upgrade all RPHY Shelf images using HTTP server, run this command
To upgrade all RPHY Shelf images using TFTP server, run this command
|
||
Step 4 |
Verify one or more RPHY Shelf 7200 chassis status. To verify one RPHY Shelf 7200 chassis status, run this command.
To verify all RPHY Shelf 7200 chassis status, run this command.
|
||
Step 5 |
To check if all RPHY Shelf 7200 chassis have been upgraded to new version 1.2 and come online succesfully you can either: Telnet to FCC IP and run the show version command or To check if one or more RPHY Shelf 7200 chassis have been upgraded, SSH to the eRPD and run the show version command. |
What to do next
These show commands may be useful in the verification test:
-
select erpd slot slot_id index index_id — RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
-
select linecard slot slot_id— RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
-
show version— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show platform— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show platform diag— Supported on cBR-8 and RPHY Shelf 7200
-
show environment— Supported on cBR-8
-
show environment all | alarms— Supported on RPHY Shelf 7200
-
show environment power— Supported on cBR-8
-
show platform hardware slot P <0-5> mcu status— Supported on cBR-8
-
show facility-alarm status — Supported on cBR-8
-
show redundancy— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show redundancy line card all— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show ip ospf neighbor— Supported on cBR-8
-
show cable modem voice— Supported on cBR-8
-
show cable calls— Supported on cBR-8
-
show cable licenses all— Supported on cBR-8
-
show inventory— Supported on cBR-8
-
show log — Supported on cBR-8 and RPHY Shelf 7200 with different outputs
-
show cable rpd— Supported on cBR-8
-
show cable modem summary total— Supported on cBR-8
-
show cable rpd lcha— Supported on cBR-8
-
show running— Supported on cBR-8 and RPHY Shelf 7200 with different outputs
-
show tech— Supported on cBR-8 and RPHY Shelf 7200 with different outputs
Upgrading cBR-8 Router Only
Before you begin
Before upgrading the system, make sure the following requirements are met:
-
All eRPDs are in init(gcp) state.
-
Download new image file from the following Cisco.com Software Center URL:
https://software.cisco.com/download/type.html?mdfid=286283913&flowid=73842
-
IOS XE Software Version 16.10.1f: cbrsup-universalk9.16.10.01f.SPA.bin
-
-
Console access for both SUPs are required.
Note |
For more information about upgrading the cBR-8 router, see https://www.cisco.com/c/en/us/td/docs/cable/cbr/upgrade/guide/b_cbr_upgrade_16_10.html. |
Procedure
Step 1 |
Copy Cisco IOS-XE Fuji 16.10.1f package to bootflash: and stby-bootflash:.
|
Step 2 |
Verify Cisco IOS-XE Fuji 16.10.1f package against the md5 hash as provided in the Cisco.com Software center.
|
Step 3 |
Backup current running config to bootflash:.
|
Step 4 |
Check system status prior to upgrade. Save the information to compare against the system status after upgrade. For the commands to use to check the status, see the show commands at the end of this section. |
Step 5 |
Configure the chassis to boot the system with Cisco IOS-XE Fuji 16.10.1f image and save running-configuration.
|
Step 6 |
Reload and bring up the cBR-8 router.
|
Step 7 |
Adjust RPD max-carrier and type, re-apply rpd-ds base-power for each RPD, save and backup current running-config.
|
Step 8 |
To check if all RPHY Shelf 7200 chassis are upgraded and come online succesfully you can either: Telnet to FCC IP and run the show version command or To check if one or more RPHY Shelf 7200 chassis have been upgraded, SSH to the eRPD and run the show version command. |
What to do next
These show commands may be useful in the verification test:
-
select erpd slot slot_id index index_id — RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
-
select linecard slot slot_id— RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
-
show version— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show platform— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show platform diag— Supported on cBR-8 and RPHY Shelf 7200
-
show environment— Supported on cBR-8
-
show environment all | alarms— Supported on RPHY Shelf 7200
-
show environment power— Supported on cBR-8
-
show platform hardware slot P <0-5> mcu status— Supported on cBR-8
-
show facility-alarm status — Supported on cBR-8
-
show redundancy— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show redundancy line card all— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
-
show ip ospf neighbor— Supported on cBR-8
-
show cable modem voice— Supported on cBR-8
-
show cable calls— Supported on cBR-8
-
show cable licenses all— Supported on cBR-8
-
show inventory— Supported on cBR-8
-
show log — Supported on cBR-8 and RPHY Shelf 7200 with different outputs
-
show cable rpd— Supported on cBR-8
-
show cable modem summary total— Supported on cBR-8
-
show cable rpd lcha— Supported on cBR-8
-
show running— Supported on cBR-8 and RPHY Shelf 7200 with different outputs
-
show tech— Supported on cBR-8 and RPHY Shelf 7200 with different outputs