Downgrading from Cisco Remote PHY for Cisco 1x2 / Compact Shelf RPD Software 5.3

Downgrading RPD and cBR-8 Router

The following scenarios are supported in downgrading the RPD and cBR-8 router.

cBR-8 original version

RPD original version

RPD state before upgrade

cBR-8 upgrade version

RPD upgrade version

RPD state after upgrade

16.9.1

5.3

online

Lower than 16.9.1

Lower than 5.3

online

16.9.1

5.3

online

Lower than 16.9.1

Lower than 5.3

init(gcp)

Note

The versions of Cisco cBR-8 router and RPD must be compatible. That is Cisco IOS XE 16.6.x works with RPD 2.x, IOS XE 16.7.x works with RPD 3.x, IOS XE 16.8.x works with RPD 4.x, and IOS XE 16.9.x works with RPD 5.x. If the versions are not matched, RPD is then in the init(gcp) state.

Before you begin

Before downgrading the system, make sure the following requirements are met:

  • Download two files from the following Cisco.com Software Center URL:

  • Console access for both SUPs are required.


Note

For more information about upgrading the cBR-8 router, see https://www.cisco.com/c/en/us/td/docs/cable/cbr/upgrade/guide/b_cbr_upgrade_16_9.html.

Procedure

Step 1

Copy Cisco IOS XE software package to bootflash: and stby-bootflash:.


copy <location>/<ios_xe_software_file> bootflash:  
copy <location>/<ios_xe_software_file> stby-bootflash:
Step 2

Verify Cisco IOS XE software package against the md5 hash as provided in the Cisco.com Software center. 


verify /md5 bootflash:<ios_xe_software_file>  
verify /md5 stby-bootflash:<ios_xe_software_file>
Step 3

Backup the current running config to bootflash:. 


copy running-config bootflash:pre-upgrade.cfg
Step 4

Check the system status prior to upgrade. It is recommended that the information is saved to compare against the system status after upgrade. For commands that are used to check the status, see the show commands at the end of this section.

Step 5

Copy the Cisco RPD image package to a TFTP server that is accessible by the RPDs.

Step 6

Verify the current RPD software version.


show cable rpd sw-version
Step 7

Downgrade all RPDs image via SSD from cBR-8.


cable rpd all ssd <tftp_server_ip> tftp <rpd_file_path>
Note 

The all command is not recommended in large scale RPD deployment. If you have many RPDs, it is recommended to upgrade the RPD per line card or per OUI.

Step 8

Verify the RPD SSD status. It will show the status as downloading.


cable rpd all ssd status
Step 9

Verify that all RPDs have downloaded the new image.


cable rpd all ssd status
show cable rpd
Step 10

Configure the chassis to boot the system with target Cisco IOS XE image. Save the running configuration.


Configure terminal
no boot system
boot system bootflash:<ios_xe_software_file>
config-register 0x2102
end
copy running-config startup-config
Step 11

Reload and start the cBR-8 router.

Reload
Step 12

Check that all the RPDs have been downgraded to the target version and that they are online.


show cable rpd
show cable rpd sw-version

What to do next

These show commands might be used during the verification test:

  • show version

  • show platform

  • show platform diag

  • show environment

  • show environment power

  • show platform hardware slot P <0-5> mcu status

  • show facility-alarm status

  • show redundancy

  • show redundancy line card all

  • show ip ospf neighbor

  • show cable modem voice

  • show cable calls

  • show cable licenses all

  • show inventory

  • show log

  • show cable rpd

  • show cable modem summary total

  • show cable rpd lcha

  • show running

  • show tech

Downgrading RPD Only

Before you begin

Before downgrading the system, make sure the following requirements are met:

  • Download new image file from the following Cisco.com Software Center URL:

    https://software.cisco.com/download/home/286316518/type

    • RPD V5.2: RPD-V5-2.itb.SSA

    • RPD V5.1.0: RPD-V5-1.itb.SSA

    • RPD V4.1.1: RPD-V4-1-1.itb.SSA,

    • RPD V3.1.1: RPD-V3-1-1.itb.SSA, or

    • RPD V2.1: RPD-V2.1_20170725011837.itb.rel.sign.SSA

Procedure

Step 1

Copy the Cisco RPD image package to a TFTP server that is accessible by the RPDs.
Step 2

Verify the current RPD software version.


show cable rpd sw-version
Step 3

Downgrade all RPDs image via SSD.


cable rpd all ssd <tftp_server_ip> tftp <rpd_file_path>
Note 

The all command is not suggested in large scale RPD deployment. If you have too many RPDs, it is recommended to upgrade the RPD per line card or per OUI.

Step 4

Verify the RPD SSD status. It will show the status as downloading.


cable rpd all ssd status
Step 5

Verify that all RPDs have downloaded the new image.


cable rpd all ssd status
show cable rpd
Step 6

Check that all the RPDs have been downgraded to the target version and that they are online.


show cable rpd
show cable rpd sw-version

What to do next

These show commands might be used during the verification test:

  • show version

  • show platform

  • show platform diag

  • show environment

  • show environment power

  • show platform hardware slot P <0-5> mcu status

  • show facility-alarm status

  • show redundancy

  • show redundancy line card all

  • show ip ospf neighbor

  • show cable modem voice

  • show cable calls

  • show cable licenses all

  • show inventory

  • show log

  • show cable rpd

  • show cable modem summary total

  • show cable rpd lcha

  • show running

  • show tech

Downgrading cBR-8 Router Only

The following scenarios are supported in downgrading the cBR-8 router.

cBR-8 original version

RPD version

RPD state before upgrade

cBR-8 upgrade version

RPD state after upgrade

16.9.1

Lower than 5.3

init(gcp)

Lower than 16.9.1

online

Before you begin

Before downgrading the system, make sure the following requirements are met:

  • Download new image file from the following Cisco.com Software Center URL:

    https://software.cisco.com/download/home/286283913/type

    • IOS XE Software Version 16.8.1: cbrsup-universalk9.16.08.01.SPA.bin,

    • IOS XE Software Version 16.7.1: cbrsup-universalk9.16.07.01.SPA.bin, or

    • IOS XE Software Version 16.6.1: cbrsup-universalk9.16.06.01.SPA.bin

  • Console access for both SUPs are required.


Note

For information about upgrading the cBR-8 router, see https://www.cisco.com/c/en/us/td/docs/cable/cbr/upgrade/guide/b_cbr_upgrade_16_8.html.

Procedure

Step 1

Copy Cisco IOS XE software package to bootflash: and stby-bootflash:.


copy <location>/<ios_xe_software_file> bootflash:  
copy <location>/<ios_xe_software_file> stby-bootflash:
Step 2

Verify the Cisco IOS XE software package against the md5 hash as provided in the Cisco.com Software center.


verify /md5 bootflash:<ios_xe_software_file>  
verify /md5 stby-bootflash:<ios_xe_software_file>
Step 3

Backup the current running config to bootflash:. 


copy running-config bootflash:pre-upgrade.cfg
Step 4

Check system status prior to downgrade. It is recommended that the information is saved to compare against the system status after upgrade. For the commands to use to check the status, see the show commands at the end of this section.

Step 5

Configure the chassis to boot the system with target Cisco IOS XE image and save the running configuration.


Configure terminal
no boot system
boot system bootflash:<ios_xe_software_file>
config-register 0x2102
end
copy running-config startup-config
Step 6

Reload and start the cBR-8 router.

Reload
Step 7

Check that all the RPDs are successfully online.


show cable rpd
show cable rpd sw-version

What to do next

The following show commands might be used during the verification test:

  • show version

  • show platform

  • show platform diag

  • show environment

  • show environment power

  • show platform hardware slot P <0-5> mcu status

  • show facility-alarm status

  • show redundancy

  • show redundancy line card all

  • show ip ospf neighbor

  • show cable modem voice

  • show cable calls

  • show cable licenses all

  • show inventory

  • show log

  • show cable rpd

  • show cable modem summary total

  • show cable rpd lcha

  • show running

  • show tech