The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This chapter describes the proprietary CISCO-SCAS-BB Management Information Base (MIB) supported by the Service Control Engine (SCE) platform.
A MIB is a database of objects that can be monitored by a network management system (NMS). The SCE platform supports both the standard MIB-II and the proprietary Cisco Service Control Enterprise MIB. The CISCO-SCAS-BB MIB is the part of the Service Control Enterprise MIB that enables the external management system to monitor counters and metrics specific to the Cisco Service Control Application for Broadband (SCA BB).
•Information About SNMP Configuration and Management
•Information About the Service Control Enterprise MIB
•Information About the CISCO-SCAS-BB MIB
•Guidelines for Using the CISCO-SCAS-BB MIB
This section explains how to configure the SNMP interface, and how to load the MIB files.
•Configuring the SNMP Interface on the SCE Platform
•The Order to Load the MIB Files
Before using the SNMP interface:
•Enable SNMP access on the SCE platform (by default, SNMP access is disabled).
•Set the values of SNMP parameters:
–The community string to be used for client authentication.
–(Optional, recommended as a security measure) An access-list (ACL) of IP addresses. This limits access to SNMP information to a set of known locations. You can define a different community string for each ACL.
–The destination IP address to which the SCE platform will send SNMP traps.
Note You can enable or disable specific traps.
For more information about SNMP configuration, see "SNMP Configuration and Management" in the "Configuring the Management Interface and Security" chapter of the Cisco Service Control Engine (SCE) Software Configuration Guide.
To access the SNMP variables on the SCE platform, you must load the SNMP browser with a standard MIB file (SNMPv2.mib) and proprietary Cisco MIB files (pcube.mib, pcubeSEMib.mib, and PCubeEngageMib.mib).
Note You can download the CISCO-SCAS-BB MIB file (PCubeEngageMib.mib) and other MIB files (pcube.mib and pcubeSEMib.mib) from ftp://ftp.cisco.com/pub/mibs/.
The SCA BB proprietary MIB uses definitions that are defined in other MIBs, such as SNMPv2.mib and pcube.mib.
This means that the order in which the MIBs are loaded is important; to avoid errors, the MIBs must be loaded in the correct order.
Load the MIBs in the following order:
1. SNMPv2.mib
2. pcube.mib
3. pcubeSEMib.mib
4. PCubeEngageMib.mib
The Service Control Enterprise MIB includes four main groups: Products, Modules, Management, and Workgroup. The Service Control enterprise tree structure is defined in a MIB file named pcube.mib.
•The pcubeProducts subtree contains the sysObjectIDs of the Service Control products.
Service Control product sysObjectIDs are defined in a MIB file named Pcube-Products-MIB.
•The pcubeModules subtree provides a root object identifier from which MIB modules are defined.
•The pcubeMgmt subtree contains the configuration copy MIB:
–pcubeConfigCopyMib enables saving the running configuration of Cisco products. This MIB is documented in the "Proprietary MIB Reference" appendix of the Cisco Service Control Engine (SCE) Software Configuration Guide.
•The pcubeWorkgroup subtree contains:
–pcubeSeEvents and pcubeSEObjs — pcubeSeMib, the SCE MIB, is the main MIB for the Service Control products and provides a wide variety of configuration and runtime statistics. This MIB is also documented in the "Proprietary MIB Reference" appendix of the Cisco Service Control Engine (SCE) Software Configuration Guide.
–pcubeEngageObjs —The CISCO-SCAS-BB MIB provides configuration and runtime status for SCA BB, and is described in the following section.
The following figure illustrates the Service Control Enterprise MIB structure.
Figure 6-1 Service Control Enterprise MIB Structure
Note The following object identifier represents the Service Control Enterprise MIB: 1.3.6.1.4.1.5655 or iso.org.dod.internet.private.enterprise.pcube.
The CISCO-SCAS-BB MIB provides access to service usage counters through the SNMP interface. Using this MIB, a network administrator can collect usage information per service at link, package, or subscriber granularity.
The CISCO-SCAS-BB MIB is defined in the file PCubeEngageMib.mib.
The MIB is documented in the remainder of this chapter.
•pcubeEngageObjs (pcubeWorkgroup 2)
This reference is divided into sections according to the MIB object groups. For each object, information is presented in the following format:
<Description of the object>
Access |
access control associated with the object |
Units |
unit of measurement used for the object |
Index
{Indexes used by the table}
Syntax
OBJECT DATA TYPE {
The general format of the object
}
The pcubeEngageObjs objects provide current information about packages, service, and subscribers.
•Service Group: serviceGrp (pcubeEngageObjs 1)
•Link Group: linkGrp (pcubeEngageObjs 2)
•Package Group: packageGrp (pcubeEngageObjs 3)
•Subscriber Group: subscriberGrp (pcubeEngageObjs 4)
•Service Counter Group: serviceCounterGrp (pcubeEngageObjs 5)
This table lists the pcubeEngageObjs objects. Each object consists of a number of subordinate object types, which are summarized in the following section.
serviceGrp |
{pcubeEngageObjs 1} |
linkGrp |
{pcubeEngageObjs 2} |
packageGrp |
{pcubeEngageObjs 3} |
subscriberGrp |
{pcubeEngageObjs 4} |
serviceCounterGrp |
{pcubeEngageObjs 5} |
This is a summary of the structure of pcubeEngageObjs. Note the table structure for objects that may have multiple entries.
serviceGrp
serviceTable—deprecated
linkGrp
linkServiceUsageTable
linkServiceUsageEntry
linkServiceUsageUpVolume linkServiceUsageDownVolume linkServiceUsageNumSessions linkServiceUsageDuration linkServiceUsageConcurrentSessions linkServiceUsageActiveSubscribers linkServiceUpDroppedPackets linkServiceDownDroppedPackets linkServiceUpDroppedBytes linkServiceDownDroppedBytes
packageGrp
packageCounterTable
packageCounterEntry
packageCounterIndex packageCounterStatus packageCounterName packageCounterActiveSubscribers
packageServiceUsageTable
packageServiceUsageEntry packageServiceUsageUpVolume packageServiceUsageDownVolume packageServiceUsageNumSessions packageServiceUsageDuration packageServiceUsageConcurrentSessions packageServiceUsageActiveSubscribers packageServiceUpDroppedPackets packageServiceDownDroppedPackets packageServiceUpDroppedBytes packageServiceDownDroppedBytes
subscriberGrp
subscribersTable
subscriberEntry
subscriberPackageIndex
subscriberServiceUsageTable
subscriberServiceUsageEntry
subscriberServiceUsageUpVolume subscriberServiceUsageDownVolume subscriberServiceUsageNumSessions subscriberServiceUsageDuration
serviceCounterGrp
globalScopeServiceCounterTable
globalScopeServiceCounterEntry
globalScopeServiceCounterIndex globalScopeServiceCounterStatus globalScopeServiceCounterName
subscriberScopeServiceCounterTable
subscriberScopeServiceCounterEntry
subscriberScopeServiceCounterIndex subscriberScopeServiceCounterStatus subscriberScopeServiceCounterName
The Service group is deprecated. Use the Service Counter group.
serviceTable (serviceGrp 1)
Deprecated—Use the tables in the Service Counter group.
Access |
not-accessible |
Syntax
Counter32
The Link Service group provides usage information per link for each global-scope service usage counter (for example, traffic statistics of a service for all subscribers using a particular link).
•linkServiceUsageTable (linkGrp 1)
•linkServiceUsageEntry (linkServiceUsageTable 1)
•linkServiceUsageUpVolume (linkServiceUsageEntry 1)
•linkServiceUsageDownVolume (linkServiceUsageEntry 2)
•linkServiceUsageNumSessions (linkServiceUsageEntry 3)
•linkServiceUsageDuration (linkServiceUsageEntry 4)
•linkServiceUsageConcurrentSessions (linkServiceUsageEntry 5)
•linkServiceUsageActiveSubscribers (linkServiceUsageEntry 6)
•linkServiceUpDroppedPackets (linkServiceUsageEntry 7)
•linkServiceDownDroppedPackets (linkServiceUsageEntry 8)
•linkServiceUpDroppedBytes (linkServiceUsageEntry 9)
•linkServiceDownDroppedBytes (linkServiceUsageEntry 10)
linkServiceUsageTable (linkGrp 1)
The Link Service Usage table provides usage information per link for each global-scope service usage counter.
Access |
not-accessible |
Syntax
SEQUENCE OF linkServiceUsageEntry
linkServiceUsageEntry (linkServiceUsageTable 1)
A Link Service Usage table entry containing parameters defining resource usage of one link for services included in one global-scope service usage counter.
Access |
not-accessible |
Index
{linkModuleIndex, linkIndex, globalScopeServiceCounterIndex}
Syntax
SEQUENCE {
linkServiceUsageUpVolume
linkServiceUsageDownVolume
linkServiceUsageNumSessions
linkServiceUsageDuration
linkServiceUsageConcurrentSessions
linkServiceUsageActiveSubscribers
linkServiceUpDroppedPackets
linkServiceDownDroppedPackets
linkServiceUpDroppedBytes
linkServiceDownDroppedBytes
}
linkServiceUsageUpVolume (linkServiceUsageEntry 1)
The upstream volume of services in this service usage counter carried over the link.
Access |
read-only |
Units |
kilobytes |
Syntax
Counter32
Note Although volume counters on the SCE platform hold 32-bit integers, CISCO-SCAS-BB MIB volume counters wraparound (turn back to zero) when the maximum 29-bit integer value (0x1FFFFFFF) is reached.
linkServiceUsageDownVolume (linkServiceUsageEntry 2)
The downstream volume of services in this service usage counter carried over the link.
Access |
read-only |
Units |
kilobytes |
Syntax
Counter32
Note Although volume counters on the SCE platform hold 32-bit integers, CISCO-SCAS-BB MIB volume counters wraparound (turn back to zero) when the maximum 29-bit integer value (0x1FFFFFFF) is reached.
linkServiceUsageNumSessions (linkServiceUsageEntry 3)
The number of sessions of services in this service usage counter carried over the link.
Access |
read-only |
Units |
sessions |
Syntax
Counter32
linkServiceUsageDuration (linkServiceUsageEntry 4)
The aggregated session duration of services in this service usage counter carried over the link.
Access |
read-only |
Units |
seconds |
Syntax
Counter32
linkServiceUsageConcurrentSessions (linkServiceUsageEntry 5)
The number of concurrent sessions of services in this service usage counter carried over the link.
Access |
read-only |
Units |
sessions |
Syntax
Counter32
linkServiceUsageActiveSubscribers (linkServiceUsageEntry 6)
The number of active subscribers of services in this service usage counter carried over the link.
Access |
read-only |
Unit |
subscribers |
Syntax
Counter32
linkServiceUpDroppedPackets (linkServiceUsageEntry 7)
The number of dropped upstream packets of services in this service usage counter carried over the link.
Access |
read-only |
Units |
packets |
Syntax
Counter32
Note To enable the SCE application to count dropped packets and dropped bytes, disable the accelerate-packet-drops
feature on the SCE platform; if accelerate-packet-drops
is enabled, the MIB dropped packets and dropped bytes counters constantly show the value 0xFFFFFFFF. For more information about the accelerate-packet-drops
feature, see "Counting Dropped Packets" in the "Configuring the Line Interface" chapter of the Cisco Service Control Engine (SCE) Software Configuration Guide.
linkServiceDownDroppedPackets (linkServiceUsageEntry 8)
The number of dropped downstream packets of services in this service usage counter carried over the link.
Access |
read-only |
Units |
packets |
Syntax
Counter32
Note To enable the SCE application to count dropped packets and dropped bytes, disable the accelerate-packet-drops
feature on the SCE platform; if accelerate-packet-drops
is enabled, the MIB dropped packets and dropped bytes counters constantly show the value 0xFFFFFFFF. For more information about the accelerate-packet-drops
feature, see "Counting Dropped Packets" in the "Configuring the Line Interface" chapter of the Cisco Service Control Engine (SCE) Software Configuration Guide.
linkServiceUpDroppedBytes (linkServiceUsageEntry 9)
The number of dropped upstream bytes of services in this service usage counter carried over the link.
Access |
read-only |
Units |
bytes |
Syntax
Counter32
Note To enable the SCE application to count dropped packets and dropped bytes, disable the accelerate-packet-drops
feature on the SCE platform; if accelerate-packet-drops
is enabled, the MIB dropped packets and dropped bytes counters constantly show the value 0xFFFFFFFF. For more information about the accelerate-packet-drops
feature, see "Counting Dropped Packets" in the "Configuring the Line Interface" chapter of the Cisco Service Control Engine (SCE) Software Configuration Guide.
linkServiceDownDroppedBytes (linkServiceUsageEntry 10)
The link service-counter number of dropped downstream bytes of services in this service usage counter carried over the link.
Access |
read-only |
Units |
bytes |
Syntax
Counter32
Note To enable the SCE application to count dropped packets and dropped bytes, disable the accelerate-packet-drops
feature on the SCE platform; if accelerate-packet-drops
is enabled, the MIB dropped packets and dropped bytes counters constantly show the value 0xFFFFFFFF. For more information about the accelerate-packet-drops
feature, see "Counting Dropped Packets" in the "Configuring the Line Interface" chapter of the Cisco Service Control Engine (SCE) Software Configuration Guide.
The Package group provides general and usage information for each global-scope package usage counter (for example, traffic statistics of a service for all subscribers assigned to a particular package or group of packages).
•packageCounterTable (packageGrp 1)
•packageCounterEntry (packageCounterTable 1)
•packageCounterIndex (packageCounterEntry 1)
•packageCounterStatus (packageCounterEntry 2)
•packageCounterName (packageCounterEntry 3)
•packageCounterActiveSubscribers (packageCounterEntry 4)
•packageServiceUsageTable (packageGrp 2)
•packageServiceUsageEntry (packageServiceUsageTable 1)
•packageServiceUsageUpVolume (packageServiceUsageEntry 1)
•packageServiceUsageDownVolume (packageServiceUsageEntry 2)
•packageServiceUsageNumSessions (packageServiceUsageEntry 3)
•packageServiceUsageDuration (packageServiceUsageEntry 4)
•packageServiceUsageConcurrentSessions (packageServiceUsageEntry 5)
•packageServiceUsageActiveSubscribers (packageServiceUsageEntry 6)
•packageServiceUpDroppedPackets (packageServiceUsageEntry 7)
•packageServiceDownDroppedPackets (packageServiceUsageEntry 8)
•packageServiceUpDroppedBytes (packageServiceUsageEntry 9)
•packageServiceDownDroppedBytes (packageServiceUsageEntry 10)
packageCounterTable (packageGrp 1)
The Package Counter table provides information for each package usage counter.
Access |
not-accessible |
Syntax
SEQUENCE OF packageCounterEntry
packageCounterEntry (packageCounterTable 1)
A Package Counter table entry containing parameters defining one package usage counter.
Access |
not-accessible |
Index
{pmoduleIndex, packageCounterIndex}
Syntax
SEQUENCE {
packageCounterIndex
packageCounterStatus
packageCounterName
packageCounterActiveSubscribers
}
packageCounterIndex (packageCounterEntry 1)
The package usage counter index.
Access |
not-accessible |
Syntax
Integer32 (1...1023)
packageCounterStatus (packageCounterEntry 2)
The package usage counter status.
Access |
read-only |
Syntax
INTEGER {
0 (disabled)
1 (enabled)
}
packageCounterName (packageCounterEntry 3)
The name of the package usage counter.
Access |
read-only |
Syntax
SnmpAdminString
packageCounterActiveSubscribers (packageCounterEntry 4)
The total number of active subscribers of packages included in the package usage counter.
Access |
read-only |
Syntax
Counter32
packageServiceUsageTable (packageGrp 2)
The Package Service Usage table provides usage information for each global-scope package usage counter.
Access |
not-accessible |
Syntax
SEQUENCE OF packageServiceUsageEntry
packageServiceUsageEntry (packageServiceUsageTable 1)
A Package Service Usage table entry containing parameters defining resource usage of packages included in one global-scope package usage counter.
Access |
not-accessible |
Index
{pmoduleIndex, packageCounterIndex, globalScopeServiceCounterIndex}
Syntax
SEQUENCE {
packageServiceUsageUpVolume
packageServiceUsageDownVolume
packageServiceUsageNumSessions
packageServiceUsageDuration
packageServiceUsageConcurrentSessions
packageServiceUsageActiveSubscribers
packageServiceUpDroppedPackets
packageServiceDownDroppedPackets
packageServiceUpDroppedBytes
packageServiceDownDroppedBytes
}
packageServiceUsageUpVolume (packageServiceUsageEntry 1)
The upstream volume of packages in this package usage counter.
Access |
read-only |
Units |
kilobytes |
Syntax
Counter32
Note Although volume counters on the SCE platform hold 32-bit integers, CISCO-SCAS-BB MIB volume counters wraparound (turn back to zero) when the maximum 29-bit integer value (0x1FFFFFFF) is reached.
packageServiceUsageDownVolume (packageServiceUsageEntry 2)
The downstream volume of packages in this package usage counter.
Access |
read-only |
Units |
kilobytes |
Syntax
Counter32
Note Although volume counters on the SCE platform hold 32-bit integers, CISCO-SCAS-BB MIB volume counters wraparound (turn back to zero) when the maximum 29-bit integer value (0x1FFFFFFF) is reached.
packageServiceUsageNumSessions (packageServiceUsageEntry 3)
The number of sessions of packages in this package usage counter.
Access |
read-only |
Units |
sessions |
Syntax
Counter32
packageServiceUsageDuration (packageServiceUsageEntry 4)
The aggregated session duration seconds of packages in this package usage counter.
Access |
read-only |
Units |
seconds |
Syntax
Counter32
packageServiceUsageConcurrentSessions (packageServiceUsageEntry 5)
The number of concurrent sessions of packages in this package usage counter.
Access |
read-only |
Units |
sessions |
Syntax
Counter32
packageServiceUsageActiveSubscribers (packageServiceUsageEntry 6)
The number of active subscribers of packages in this package usage counter.
Access |
read-only |
Units |
subscribers |
Syntax
Counter32
packageServiceUpDroppedPackets (packageServiceUsageEntry 7)
The number of dropped upstream packets of packages in this package usage counter.
Access |
read-only |
Units |
packets |
Syntax
Counter32
Note To enable the SCE application to count dropped packets and dropped bytes, disable the accelerate-packet-drops
feature on the SCE platform; if accelerate-packet-drops
is enabled, the MIB dropped packets and dropped bytes counters constantly show the value 0xFFFFFFFF. For more information about the accelerate-packet-drops
feature, see "Counting Dropped Packets" in the "Configuring the Line Interface" chapter of the Cisco Service Control Engine (SCE) Software Configuration Guide.
packageServiceDownDroppedPackets (packageServiceUsageEntry 8)
The number of dropped downstream packets of packages in this package usagecounter.
Access |
read-only |
Units |
packets |
Syntax
Counter32
Note To enable the SCE application to count dropped packets and dropped bytes, disable the accelerate-packet-drops
feature on the SCE platform; if accelerate-packet-drops
is enabled, the MIB dropped packets and dropped bytes counters constantly show the value 0xFFFFFFFF. For more information about the accelerate-packet-drops
feature, see "Counting Dropped Packets" in the "Configuring the Line Interface" chapter of the Cisco Service Control Engine (SCE) Software Configuration Guide.
packageServiceUpDroppedBytes (packageServiceUsageEntry 9)
The number of dropped upstream bytes of packages in this package usage counter.
Access |
read-only |
Units |
bytes |
Syntax
Counter32
Note To enable the SCE application to count dropped packets and dropped bytes, disable the accelerate-packet-drops
feature on the SCE platform; if accelerate-packet-drops
is enabled, the MIB dropped packets and dropped bytes counters constantly show the value 0xFFFFFFFF. For more information about the accelerate-packet-drops
feature, see "Counting Dropped Packets" in the "Configuring the Line Interface" chapter of the Cisco Service Control Engine (SCE) Software Configuration Guide.
packageServiceDownDroppedBytes (packageServiceUsageEntry 10)
The number of dropped downstream bytes of packages in this package usage counter.
Access |
read-only |
Units |
bytes |
Syntax
Counter32
Note To enable the SCE application to count dropped packets and dropped bytes, disable the accelerate-packet-drops
feature on the SCE platform; if accelerate-packet-drops
is enabled, the MIB dropped packets and dropped bytes counters constantly show the value 0xFFFFFFFF. For more information about the accelerate-packet-drops
feature, see "Counting Dropped Packets" in the "Configuring the Line Interface" chapter of the Cisco Service Control Engine (SCE) Software Configuration Guide.
The Subscriber group provides general information for each subscriber and usage information per service usage counter for each subscriber (for example, traffic statistics of a service for a particular subscriber defined in the system).
Note To use the tables in this group, first create an entry to reference a particular subscriber in the subscribersPropertiesValueTable object of the subscriberGrp in the SCE MIB (not the CISCO-SCAS-BB MIB). Using the index of this table (spvIndex), information about the subscriber can be collected. For more information about how to access subscriber-level information using the SNMP interface, see Accessing Subscriber Information (the spvIndex).
•subscribersTable (subscriberGrp 1)
•subscribersEntry (subscribersTable 1)
•subscriberPackageIndex (subscribersEntry 1)
•subscriberServiceUsageTable (subscriberGrp 2)
•subscriberServiceUsageEntry (subscriberServiceUsageTable 1)
•subscriberServiceUsageUpVolume (subscriberServiceUsageEntry 1)
•subscriberServiceUsageDownVolume (subscriberServiceUsageEntry 2)
•subscriberServiceUsageNumSessions (subscriberServiceUsageEntry 3)
•subscriberServiceUsageDuration (subscriberServiceUsageEntry 4)
subscribersTable (subscriberGrp 1)
The Subscribers Table provides information for each subscriber.
Access |
not-accessible |
Syntax
SEQUENCE OF subscribersEntry
subscribersEntry (subscribersTable 1)
A Subscribers Table entry containing the package index of each subscriber.
Access |
not-accessible |
Index
{pmoduleIndex, spvIndex}
Syntax
SEQUENCE {
subscriberPackageIndex
}
subscriberPackageIndex (subscribersEntry 1)
The package index of the subscriber's package.
Access |
read-only |
Syntax
Integer32 (1...255)
subscriberServiceUsageTable (subscriberGrp 2)
The Subscriber Service Usage table provides usage information per service usage counter for each subscriber.
Access |
not-accessible |
Syntax
Sequence of subscriberServiceUsageEntry
subscriberServiceUsageEntry (subscriberServiceUsageTable 1)
A Subscriber Service Usage table entry containing parameters defining resource usage by one subscriber of services included in one service usage counter.
Access |
not-accessible |
Index
{pmoduleIndex, spvIndex, subscriberScopeServiceCounterIndex}
Syntax
SEQUENCE {
subscriberServiceUsageUpVolume
subscriberServiceUsageDownVolume
subscriberServiceUsageNumSessions
subscriberServiceUsageDuration
}
subscriberServiceUsageUpVolume (subscriberServiceUsageEntry 1)
The upstream volume of services in this service usage counter used by this subscriber.
Access |
read-only |
Unit |
kilobytes |
Syntax
Counter32
Note Although volume counters on the SCE platform hold 32-bit integers, CISCO-SCAS-BB MIB volume counters wraparound (turn back to zero) when the maximum 29-bit integer value (0x1FFFFFFF) is reached.
subscriberServiceUsageDownVolume (subscriberServiceUsageEntry 2)
The downstream volume of services in this service usage counter used by this subscriber.
Access |
read-only |
Unit |
kilobytes |
Syntax
Counter32
Note Although volume counters on the SCE platform hold 32-bit integers, CISCO-SCAS-BB MIB volume counters wraparound (turn back to zero) when the maximum 29-bit integer value (0x1FFFFFFF) is reached.
subscriberServiceUsageNumSessions (subscriberServiceUsageEntry 3)
The number of sessions of services in this service usage counter used by this subscriber.
Access |
read-only |
Unit |
sessions |
Syntax
Integer32 (1...65535)
subscriberServiceUsageDuration (subscriberServiceUsageEntry 4)
Aggregated session duration of services in this service usage counter used by this subscriber.
Access |
read-only |
Units |
seconds |
Syntax
Integer32 (1...65535)
The Service Counter group provides general information for each global-scope and subscriber-scope service usage counter. You can use it, for example, to read the names of the services as defined in a SCA BB service configuration.
•globalScopeServiceCounterTable (serviceCounterGrp 1)
•globalScopeServiceCounterEntry (globalScopeServiceCounterTable 1)
•globalScopeServiceCounterIndex (globalScopeServiceCounterEntry 1)
•globalScopeServiceCounterStatus (globalScopeServiceCounterEntry 2)
•globalScopeServiceCounterName (globalScopeServiceCounterEntry 3)
•subscriberScopeServiceCounterTable (serviceCounterGrp 2)
•subscriberScopeServiceCounterEntry (subscriberScopeServiceCounterTable 1)
•subscriberScopeServiceCounterIndex (subscriberScopeServiceCounterEntry 1)
•subscriberScopeServiceCounterStatus (subscriberScopeServiceCounterEntry 2)
•subscriberScopeServiceCounterName (subscriberScopeServiceCounterEntry 3)
globalScopeServiceCounterTable (serviceCounterGrp 1)
The Global-Scope Service Counter table consists of data about each service usage counter used by the link and by packages.
Access |
not-accessible |
Syntax
SEQUENCE OF globalScopeServiceCounterEntry
globalScopeServiceCounterEntry (globalScopeServiceCounterTable 1)
A Global-Scope Service Counter table entry containing parameters defining one global-scope service usage counter.
Access |
not-accessible |
Index
{pmoduleIndex, globalScopeServiceCounterIndex}
Syntax
SEQUENCE {
globalScopeServiceCounterIndex
globalScopeServiceCounterStatus
globalScopeServiceCounterName
}
globalScopeServiceCounterIndex (globalScopeServiceCounterEntry 1)
The global-scope service usage counter index.
Access |
not-accessible |
Syntax
Integer32 (1...255)
globalScopeServiceCounterStatus (globalScopeServiceCounterEntry 2)
The global-scope service usage counter status.
Access |
read-only |
Syntax
INTEGER {
0 (disabled)
1 (enabled)
}
globalScopeServiceCounterName (globalScopeServiceCounterEntry 3)
The name of the global-scope service usage counter.
Access |
read-only |
Syntax
SnmpAdminString
subscriberScopeServiceCounterTable (serviceCounterGrp 2)
The Subscriber-Scope Service Counter table consists of data about each service usage counter used by subscribers.
Access |
not-accessible |
Syntax
SEQUENCE OF subscriberScopeServiceCounterEntry
subscriberScopeServiceCounterEntry (subscriberScopeServiceCounterTable 1)
A Subscriber-Scope Service Counter table entry containing parameters defining one subscriber-scope service usage counter.
Access |
not-accessible |
Index
{pmoduleIndex, subscriberScopeServiceCounterIndex}
Syntax
SEQUENCE {
subscriberScopeServiceCounterIndex
subscriberScopeServiceCounterStatus
subscriberScopeServiceCounterName
}
subscriberScopeServiceCounterIndex (subscriberScopeServiceCounterEntry 1)
The subscriber-scope service usage counter index.
Access |
not-accessible |
Syntax
Integer32 (1...255)
subscriberScopeServiceCounterStatus (subscriberScopeServiceCounterEntry 2)
The subscriber-scope service usage counter status.
Access |
read-only |
Syntax
INTEGER {
0 (disabled)
1 (enabled)
}
subscriberScopeServiceCounterName (subscriberScopeServiceCounterEntry 3)
The name of the subscriber-scope service usage counter.
Access |
read-only |
Syntax
SnmpAdminString
This section provides guidelines to help access SNMP information about the SCE platform using the CISCO-SCAS-BB MIB.
Note Indices in SNMP start from 1; SCA BB indices start from 0. When accessing a counter in the SCA BB SNMP MIB by its index, add 1 to the index of the entity. For example, the global usage counter with index 0 will be located at globalScopeServiceCounter index 1.
Note Although volume counters on the SCE platform hold 32-bit integers, CISCO-SCAS-BB MIB volume counters wraparound (turn back to zero) when the maximum 29-bit integer value (0x1FFFFFFF) is reached.
Note To enable the SCE application to count dropped packets and dropped bytes, disable the accelerate-packet-drops feature on the SCE platform; if accelerate-packet-drops is enabled, the MIB dropped packets and dropped bytes counters constantly show the value 0xFFFFFFFF.
For more information about the accelerate-packet-drops feature, see "Counting Dropped Packets" in the "Configuring the Line Interface" chapter of the Cisco Service Control Engine (SCE) Software Configuration Guide.
•globalScopeServiceCounterTable and subscriberScopeServiceCounterTable
•Accessing Subscriber Information (the spvIndex)
The index of a service usage counter as defined in a SCA BB service configuration is used to reference services in the CISCO-SCAS-BB MIB. Since MIB index values count from 1, but SCA BB indices count from 0, the index used in the MIB must always be one greater than the index of the service it is referencing.
For example, to get the number of upstream bytes used by a service on a link, use LinkServiceTable.lnkServiceUpVolume (part of the linkGrp). The value assigned to serviceIndex for this table must be one greater than service index defined for this service in the service configuration.
To identify or change the index of a service, go to the Advanced tab of the Service Settings dialog box in the SCA BB Console (see the "Using the Service Configuration Editor: Traffic Classification" chapter of the Cisco Service Control Application for Broadband User Guide). For example, to reference the P2P service (which has a (default) service index of 9) in the MIB, a serviceIndex of 10 (= 9 + 1) must be used.
The package index, defined in a SCA BB service configuration, is used to reference entries in packageTable and packageServiceTable (part of the packageGrp). As with serviceIndex the value assigned to packageIndex must be one greater than the package index in the service configuration.
To identify or change the index of a package, go to the Advanced tab of the Package Settings dialog box in the SCA BB Console (see the "Using the Service Configuration Editor: Traffic Control" chapter of the Cisco Service Control Application for Broadband User Guide). For example, to reference the default package (which has a package index of 0) in the MIB, a packageIndex of 1 (= 0 + 1) must be used.
In order to collect subscriber-level information using the SNMP interface, you must first create an entry in the subscriberPropertiesValuesTable
part of the subscriberGrp
in pcubeSEMib (not PCubeEngageMib). After an entry in this table is created and associated with a subscriber name, its index (spvIndex)
can be referred to in PCubeEngageMib to collect usage statistics for this subscriber.
An entry is created in the subscriberPropertiesValuesTable
table by setting the entry spvRowStatus
object with CreateAndGo(4)
then setting the name of the subscriber in the spvSubName
property and the spvIndex
variable to be used as an index to the subscriber.
The fiollowing procedure demonstrates how to poll the downstream volume of subscriber "sub123" for the P2P service using PCubeEngageMib.
Step 1 Obtain the index of the P2P service from the SCA BB Console.
This is a one-time operation that you should perform only if services are changed in the service configuration. [In this example, assume that the P2P service index has its default value of 9.]
Step 2 Create an entry in SEMib:subscriberGrp:subscriberPropertiesValuesTable
.
Step 3 Set the object indices.
•For pmoduleIndex
use 1.
•Set spvIndex
to the desired value. [In this example we will use 1.]
Step 4 Set spvRowStatus
to 4 (using CreateAndGo).
Step 5 Set spvSubName
to "sub123".
Step 6 Read the subscriberServiceDownVolume
property out of EngageMib:subscriberGrp:subscriberServiceTable
where spvIndex
is set to 1 and serviceIndex
is set to 10.