Prerequisites
This section provides detailed information about the prerequisites that you must complete before launching Cisco Nexus Dashboard Fabric Controller.
Nexus Dashboard
You must have Cisco Nexus Dashboard cluster deployed and its fabric connectivity configured, as described in Cisco Nexus Dashboard Deployment Guide before proceeding with any additional requirements and the Nexus Dashboard Fabric Controller service installation described here.
![]() Note |
The Fabric Controller service cannot recover from a two If you run into a situation where two |
NDFC Release |
Minimum Nexus Dashboard Release |
---|---|
Release 12.1.1e |
Cisco Nexus Dashboard, Release 2.2.1h or later |
The following Nexus Dashboard form factors are supported with NDFC deployments:
-
Cisco Nexus Dashboard physical appliance (.iso)
-
VMware ESX (.ova)
-
ESXi 6.7
-
ESXi 7.0
-
-
Linux KVM (.qcow2)
-
CentOS 7.9
-
-
Existing Red Hat Enterprise Linux (SAN Controller persona only)
-
RedHat Enterprise Linux (RHEL) 8.4
-
Sizing of the Cluster
Refer to your release-specific Verified Scalability Guide for NDFC for information about the number of Nexus Dashboard cluster nodes required for the desired scale.
Nexus Dashboard supports co-hosting of services. Depending on the type and number of services you choose to run, you may be required to deploy extra worker nodes in your cluster. For cluster sizing information and recommended number of nodes based on specific use cases, see the Cisco Nexus Dashboard Capacity Planning tool.
Network Connectivity
-
LAN Device Management Connectivity – Fabric discovery and Fabric controller features can manage Devices over both Management Network and Data Network of ND Cluster Appliances.
-
When using Management network, add the routes to all subnets of the devices that NDFC needs to manage or monitor in the Management Network.
-
When using Data Network, add the route towards a DHCP relay server in the Data Network.
-
SAN controller persona requires all the devices to be reachable via the Data network of Nexus Dashboard cluster nodes.
Persistent IP address
-
Persistent IPs are needed by NDFC for multiple use cases.
-
If Nexus Dashboard cluster is deployed over a Layer 3 separation of network, configure BGP on all ND nodes.
-
All Persistent IPs must be configured such that they are not part of any of the Nexus Dashboard nodes' subnets. This is supported only when LAN Device Management connectivity is Data. This is not supported with a cluster that co-hosts Nexus Dashboard Insights with NDFC.
-
If Nexus Dashboard cluster is deployed with all nodes in the same subnet, persistent IPs can be configured to be from the same subnet.
In this case, persistent IPs must belong to the network chosen based on LAN Device Management connectivity setting in the NDFC Server Settings.
For more information, see Persistent IP Requirements for NDFC.
-
Fabric Discovery – 2 IPs based on LAN Device Management Connectivity.
-
Fabric Controller – 2 based on LAN Device Management connectivity and 1 for each EPL fabric instance
-
Fabric Controller with IPFM – 2 based on LAN Device Management connectivity
-
1 IP for ingest of software Telemetry for a single node IPFM deployment
-
3 IPs for ingest of software Telemetry for a three node IPFM deployment
-
-
SAN Controller:
-
SAN Controller 3 Node Cluster – 2 IPs for Data Network + 3 IPs for SAN Insights
-
SAN Controller 1 Node Cluster – 2 IPs for Data Network + 1 IP for SAN Insights
-
POAP related requirements
-
Devices must support POAP.
-
Device must have no start up configuration or boot poap enable command must be configured to bypass the start up configuration and enter the POAP mode.
-
DHCP server with scope defined.
-
The script server that stores POAP script and devices’ configuration files must be accessible.
-
Software and Image Repository server must be used to store software images for the devices.
Network Time Protocol (NTP)
Nexus Dashboard nodes must be in synchronization with the NTP Server; however, there can be latency of up to 1 second between the Nexus Dashboard nodes. If the latency is greater than or equal to 1 second between the Nexus Dashboard nodes, this may result in unreliable operations on the NDFC cluster.
Restoring configurations
If this system is to be restored from the previously taken backup, you must upload a backup file that was taken from the same version.