- Welcome to the Cisco Nexus 3550F Fusion Documentation
-
- Command Line Interface
- Configuration Management
- User Management
- Diagnostics
- Statistics Logging
- Configuring Ports
- Packet Capture
- Patches and Taps
- FPGA Module
- Switch Objects
- Mux Objects
- MAC Address Table
- IGMP and Multicast
- VLAN Support
- Mirror and Timestamping Fusion
- Mirror and Timestamping Fusion HPT
- Virtual Ports
- LLDP
- SNMP
- TACACS+
- Access Control
- Latency Statistics
- BGP
- Bash Shell
- Automatic Configuration
- Known Issues
Commands
Commands can be sent to the Cisco Nexus 3550-F Fusion (formerly ExaLINK Fusion) using a command line interface, of which the available commands are listed below.
Note
The CLI has a modal structure. User permissions/roles are not tested on entry to various operating modes, however they are tested when a command is executed within a mode. For example, all users can enter config port however only users with appropriate roles can execute a command such as setting the speed for that port.
NoteCommands that are preceded by config or debug do not need that prefix at the start when in the corresponding mode.
| Name | Description | Min reqd. role |
|---|---|---|
| show version | Show software and hardware version. | guest |
| show uptime | Display how long the Nexus 3550-F has been active for. | guest |
| show diagnostic | Show hardware diagnostics. | guest |
| show temperature | Show temperature measurements. | guest |
| show fan-speed | Show the speed (RPM) of every connected fan module. | guest |
| show power-supply | Show power supply diagnostics. | guest |
| show power | Show voltage and current measurements. | guest |
| show users | Display list of all users. | guest |
| config password <user> | Set password for the specified user. Note: a user will be able to change their own password, but not anyone else's without sufficient permission. If an argument is not provided to the command, it will default to changing the current user's password. |
admin |
| exit | Exit current mode. | guest |
| logout | Terminate the current session. | guest |
| configure | Enters configuration mode (identical to config). Note: Refer to the note at the top of this table re entering modes. |
N/A |
| ping <ip_address> | Use the management interface to ping a given IP address. | guest |
| show time | Show the current time. | guest |
| show port [<port>] | Displays port details or a summary of all ports. | monitor |
| port <port> | Select a port to operate on. | N/A |
| config port <port> | Enters configuration mode for specified port. | N/A |
| config port <port> alias <alias> | Assign an alias to a port. | user |
| config port <port> no alias | Remove an alias from a port. | user |
| config port <port> description <description> | Assign a description to port. | user |
| config port <port> no description | Remove a description from a port. | user |
| config port <port> speed <mbps> | Configure the speed of a port. | user |
| config port <port> autoneg <enable|disable> | Enable or disable autonegotiation on a port. | user |
| config port <port> link-gen | Enable simulated link generation on a port. | user |
| config port <port> no link-gen | Disable simulated link generation on a port. | user |
| config port <port> enable | Enable a port. | user |
| config port <port> disable | Disable a port. | user |
| config port <port> reset counters | Reset a port's packet statistics. | user |
| port <port> show latency | Generate a latency histogram of the port. | monitor |
| port <port> show latency last <n> | Generate a latency histogram of the port using the last n bins. | monitor |
| show lldp neighbors | Display a table of all neighboring devices found via LLDP. | monitor |
| config port <port> lldp transmit | Enable LLDP on the specified port. | user |
| config port <port> no lldp transmit | Disable LLDP on the specified port. | user |
| show patch | Display all currently patched ports. | monitor |
| config patch <port1> <port2> | Create a new patch between two ports. | operator |
| config no patch <port1> <port2> | Delete an existing patch between two ports. | operator |
| show tap | Display all currently tapped ports. | monitor |
| config tap <src_port> <destination> | Create a tap of incoming traffic from src_port to the destination. | operator |
| config no tap <src_port> <destination> | Remove a specified tap. | operator |
| config tap output <src_port> <destination> | Create a tap of outgoing traffic from src_port to the destination. | operator |
| config no tap output <src_port> <destination> | Remove a specified output tap. | operator |
| show mux | Show a summary of mux objects. | monitor |
| config mux <name> show | Show config for the selected mux. | operator |
| config mux <name> | Create/edit mux object with specified name. | operator |
| config no mux <name> | Delete mux object with specified name. | operator |
| config mux <name> mode <mode> | Set the operating mode of a mux object. | operator |
| config mux <name> port <port> | Add a downstream port on the selected mux. | operator |
| config mux <name> no port <port> | Remove port from the selected mux. | operator |
| config mux <name> port upstream <port> | Assign an upstream port for the selected mux. | operator |
| config mux <name> no port upstream <port> | Remove upstream port from the selected mux. | operator |
| config mux <name> igmp <flood-unknown mrouter | snooping | static-group> | Set the IGMP operating mode for the selected mux. | operator |
| config mux <name> <vlan-enable> | Enable VLAN operation for the selected mux. | operator |
| config mux <name> mac-address-table static <mac address> port <port> | Add a static route for the selected mux. | operator |
| show switch | Show a summary of switch objects. | monitor |
| config switch <switch> show | Show configuration of selected switch. | monitor |
| config switch <name> | Create/edit a switch object with specified name. | operator |
| config no switch <name> | Delete specified switch object. | operator |
| config switch <switch> port <port> | Add port to the selected switch. | operator |
| config switch <switch> no port <port> | Remove port from selected switch. | operator |
| show mirror | Show a summary of mirror objects. | monitor |
| config mirror <name> show | Show config for the selected mirror object. | monitor |
| config mirror <name> | Create/edit a mirror with specified name. | operator |
| config no mirror <name> | Delete a specified mirror. | operator |
| config mirror <name> output <port> | Assign port to be an output for selected mirror. | operator |
| config mirror <name> no output <port> | Remove output port from the selected mirror. | operator |
| config mirror <name> port <port> | Assign port as input for selected mirror. | operator |
| config mirror <name> no port <port> | Remove port as input for selected mirror. | operator |
| config mirror <name> switch <name> | Add switch object to selected mirror. | operator |
| config mirror <name> no switch <name> | Remove a switch object from the selected mirror. | operator |
| config mirror <name> timestamp <none fcs | fcs-compat | append | append-compat > | Configure timestamping on the selected mirror. | operator |
| config mirror <name> no timestamp | Disable timestamping on selected mirror. | operator |
| show log [last <n>] [reverse] [level <priority> [contains <string>] [all <id> ...] | Display the Nexus 3550-F's log of activity. | monitor |
| show remote-logging | Displays remote-logging configuration and status. | monitor |
| config remote-logging target <type> <address> <facility> <level> | Add remote logging of specified setting. | admin |
| config remote-logging reset | Clear out and disable remote logging. | admin |
| config remote-logging enable | Enable remote logging. | admin |
| config remote-logging disable | Disable remote logging. | admin |
| debug dump | Create a .tar file detailing the current running state of the Nexus 3550-F. | operator |
| config show snmp | Show SNMP configuration. | monitor |
| config no snmp | Clear out all SNMP settings and disable SNMP. | admin |
| config snmp disable | Disable SNMP, while retaining current settings. | admin |
| config snmp enable | Enable SNMP. | admin |
| config snmp read community <password> | Set the shared phrase used to identify a readonly community. | admin |
| config snmp contact <contact> | Set the contact details that will be displayed in SNMP object sysContact. | admin |
| config snmp location <location> | Set the location details that will be displayed in SNMP object sysLocation. | admin |
| config snmp port <port> | Set the SNMP port, or set to zero for the default. | admin |
| config no snmp trap | Clear out all SNMP Trap settings and disable SNMP Trap. | admin |
| config snmp trap disable | Disable the sending of SNMP Traps. | admin |
| config snmp trap enable | Enable the sending of SNMP Traps. | admin |
| config snmp trap target <address> <community> | Set an additional address to which SNMP Traps will be sent, using the given community string. | admin |
| show telnet | Display telnet status. | monitor |
| config telnet enable | Enable telnet access. | admin |
| config telnet disable | Disable telnet access. | admin |
| show tacacs | Show TACACS+ configuration. | monitor |
| config no tacacs | Reset all TACACS+ configuration. | admin |
| config tacacs disable | Disable TACACS+ authentication, authorization and accounting. | admin |
| config tacacs enable | Enable TACACS+ authentication, authorization and accounting. | admin |
| config tacacs server <server>... | Set list of TACACS+ servers to be used. | admin |
| config tacacs secret <secret> | Set the TACACS+ shared secret, used for encryption. | admin |
| config tacacs service <service> | Set the service name, used by the remote TACACS+ server. | admin |
| config tacacs timeout <seconds> | Set the TACACS+ request timeout. | admin |
| config tacacs periodic <seconds> | Configure TACACS+ to periodically check authorization levels of users. | admin |
| config tacacs no periodic | Disable periodic authorization level checks in TACACS+. | admin |
| config tacacs accounting <level> | Configure TACACS+ accounting to be disabled, standard or verbose. | admin |
| show running-config | Display the current configuration settings. | monitor |
| show startup-config | Display the startup configuration settings. | monitor |
| config copy running-config startup-config | Save running configuration to startup. | admin |
| config copy startup-config running-config | Load startup configuration. | admin |
| config erase startup-config | Erase all of the saved configuration files. | admin |
| config erase running-config <all management | module | data-plane> | Erase some or all of the currently running configuration. | admin |
| config optimize | Attempt to reallocate switch resources in a more optimized way. | operator |
| config license reload | Reload a previously entered license. | admin |
| config license set | Enter a license key for the Nexus 3550-F. | admin |
| config license erase | Erase a current set license key for the Nexus 3550-F. | admin |
| config time set <time> | Set the current time on the Nexus 3550-F. Note: Accepted format is [YYYY-MM-DD] HH:MM:SS |
operator |
| show timesync |
Display the current time synchronization settings. | monitor |
| config timesync ntp <server>... ptp <domain> pps <edge> [cable-delay <delay>] ntp+pps <server>... [<edge>] [cable-delay <delay>] ptp+pps [<domain> [<edge>]] [cable-delay <delay>] gps [antenna-delay <nanoseconds>] none |
Configure time synchronization settings. | operator |
| config timesync output pps <rising|falling> | Set the PPS output to either the rising or falling edge. | operator |
| config no timesync | Disable time synchronization. | operator |
| config session-timeout <seconds|default> | Set automatic logout to the specified number of seconds or a default value. | admin |
| show auto-config | Shows whether auto-config is enabled or not. | guest |
| config auto-config <enabled|disabled> | Enable or disable auto-configuration. | admin |
| config hostname <hostname> | Configure hostname of the device. | admin |
| show management address | Display IPv4 address for the management interface. | guest |
| config management address dhcp | Configure management interface using DHCP. | admin |
| config management address static <address> <netmask> [gateway] | Configure a static IPv4 address on the management interface. | admin |
| show management name-server | Shows the name server(s) on the management interface. | guest |
| config management name-server <name server> ... | Configure a name server on the management interface. | admin |
| show management access-list | Show access control rules. | monitor |
| config management access-list allow <address range>... | Extend access control rules to allow connections from the supplied IPv4 address ranges. | admin |
| config management access-list deny <address range>... | Extend access control rules to deny connections from the supplied IPv4 address ranges. | admin |
| config no management access-list | Reset all access control rules. | admin |
| config module <X|Y> function <switch mux custom> | Load the switch or mux bitfile onto the FPGA module, or set it to accept a custom bitfile. | operator |
| config module <X|Y> power <onoff> | Enable or disable power to the internal module. | operator |
| config module <X|Y> fpga bitstream <bitstream> | Set a custom bitstream onto FPGA module. | operator |
| config module <X|Y> fpga reconfigure | Reconfigure the FPGA module according to the custom bitfile. | operator |
| config module <X|Y> fpga xvc-server port <port> | Enable the XVC server for the FPGA on the specified module. | operator |
| config module <X|Y> no fpga xvc-server | Disable a currently running XVC server for the FPGA on the specified module. | operator |
| config module <X|Y> serial-server <tcp-port> | Enable the serial server of the specified module. | operator |
| config module <X|Y> no serial-server | Disable a currently running serial server on the specified module. | operator |
| show services | Show which services are running. | monitor |
| config http enable | Enable http access for JSON RPC API. | admin |
| config http disable | Disable http access for JSON RPC API. | admin |
| config update file <tar file> | Update system from an uploaded file. | admin |
| config update usb <tar file> | Update system from a file on an attached USB drive. | admin |
| config update tftp <server> <tar file> | Download and update system from a file from a tftp server. | admin |
| reboot | Restart the device. | operator |
| reboot in [<hh>:]<mm> | Restart the device after the specified amount of time has passed. | operator |
| reboot cancel | Cancel a previously scheduled reboot. | operator |
Feedback