Configuring RIP

This chapter describes how to configure the Routing Information Protocol (RIP) on Cisco NX-OS switches.

This chapter includes the following sections:

Information About RIP

This section includes the following topics:

RIP Overview

RIP uses User Datagram Protocol (UDP) data packets to exchange routing information in small internetworks. RIPv2 supports IPv4. RIPv2 uses an optional authentication feature supported by the RIPv2 protocol (see the RIPv2 Authentication section).

RIP uses the following two message types:

  • Request—Sent to the multicast address 224.0.0.9 to request route updates from other RIP-enabled routers.

  • Response—Sent every 30 seconds by default (see the Verifying the RIP Configuration section). The router also sends response messages after it receives a Request message. The response message contains the entire RIP route table. RIP sends multiple response packets for a request if the RIP routing table cannot fit in one response packet.

RIP uses a hop count for the routing metric. The hop count is the number of routers that a packet can traverse before reaching its destination. A directly connected network has a metric of 1; an unreachable network has a metric of 16. This small range of metrics makes RIP an unsuitable routing protocol for large networks.

RIPv2 Authentication

You can configure authentication on RIP messages to prevent unauthorized or invalid routing updates in your network. Cisco NX-OS supports a simple password or an MD5 authentication digest.

You can configure the RIP authentication per interface by using key-chain management for the authentication keys. Key-chain management allows you to control changes to the authentication keys used by an MD5 authentication digest or simple text password authentication. See the Cisco Nexus 3548 Switch NX-OS Security Configuration Guide for more details about creating key-chains.

To use an MD5 authentication digest, you configure a password that is shared at the local router and all remote RIP neighbors. Cisco NX-OS creates an MD5 one-way message digest based on the message itself and the encrypted password and sends this digest with the RIP message (Request or Response). The receiving RIP neighbor validates the digest by using the same encrypted password. If the message has not changed, the calculation is identical and the RIP message is considered valid.

An MD5 authentication digest also includes a sequence number with each RIP message to ensure that no message is replayed in the network.

Split Horizon

You can use split horizon to ensure that RIP never advertises a route out of the interface where it was learned.

Split horizon is a method that controls the sending of RIP update and query packets. When you enable split horizon on an interface, Cisco NX-OS does not send update packets for destinations that were learned from this interface. Controlling update packets in this manner reduces the possibility of routing loops.

You can use split horizon with poison revers to configure an interface to advertise routes learned by RIP as unreachable over the interface that learned the routes. Figure below shows a sample RIP network with split horizon with poison reverse enabled.

Figure 1. RIP with Split Horizon Poison Reverse

Router C learns about route X and advertises that route to router B. Router B in turn advertises route X to router A, but sends a route X unreachable update back to router C.

By default, split horizon is enabled on all interfaces.

Route Filtering

You can configure a route policy on a RIP-enabled interface to filter the RIP updates. Cisco NX-OS updates the route table with only those routes that the route policy allows.

Route Summarization

You can configure multiple summary aggregate addresses for a specified interface. Route summarization simplifies route tables by replacing a number of more-specific addresses with an address that represents all the specific addresses. For example, you can replace 10.1.1.0/24, 10.1.2.0/24, and 10.1.3.0/24 with one summary address, 10.1.0.0/16.

If more specific routes are in the routing table, RIP advertises the summary address from the interface with a metric equal to the maximum metric of the more specific routes.


Note


Cisco NX-OS does not support automatic route summarization.


Route Redistribution

You can use RIP to redistribute static routes or routes from other protocols. When you configure redistribution use a route policy to control which routes are passed into RIP. A route policy allows you to filter routes based on attributes such as the destination, origination protocol, route type, route tag, and so on. For more information, see Configuring Route Policy Manager.

Whenever you redistribute routes into a RIP routing domain, by default Cisco NX-OS does not redistribute the default route into the RIP routing domain. You can generate a default route into RIP, which can be controlled by a route policy.

You also configure the default metric that is used for all imported routes into RIP.

Load Balancing

You can use load balancing to allow a router to distribute traffic over all the router network ports that are the same distance from the destination address. Load balancing increases the utilization of network segments and increases effective network bandwidth.

Cisco NX-OS supports the Equal Cost Multiple Paths (ECMP) feature with up to 32 equal-cost paths in the RIP route table and the unicast RIB. You can configure RIP to load balance traffic across some or all of those paths.

Virtualization Support

Cisco NX-OS supports multiple instances of the RIP protocol that runs on the same system. RIP supports Virtual Routing and Forwarding instances (VRFs).

By default, Cisco NX-OS places you in the default VRF unless you specifically configure another VRF.

Prerequisites for RIP

RIP has the following prerequisites:

Guidelines and Limitations for RIP

RIP has the following configuration guidelines and limitations:

  • Cisco NX-OS does not support RIPv1. If Cisco NX-OS receives a RIPv1 packet, it logs a message and drops the packet.

  • Cisco NX-OS does not establish adjacencies with RIPv1 routers.

Default Settings for RIP

The following table lists the default settings for RIP parameters.

Table 1. Default RIP Parameters

Parameters

Default

Maximum paths for load balancing

16

RIP feature

Disabled

Split horizon

Enabled

Configuring RIP


Note


If you are familiar with the Cisco IOS CLI, be aware that the Cisco NX-OS commands for this feature might differ from the Cisco IOS commands that you would use.


Enabling the RIP Feature

You must enable the RIP feature before you can configure RIP.

SUMMARY STEPS

  1. configure terminal
  2. feature rip
  3. (Optional) show feature
  4. (Optional) copy running-config startup-config

DETAILED STEPS

  Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters configuration mode.

Step 2

feature rip

Example:

switch(config)# feature rip

Enables the RIP feature.

Step 3

(Optional) show feature

Example:

switch(config)# show feature
(Optional)

Displays enabled and disabled features.

Step 4

(Optional) copy running-config startup-config

Example:

switch(config)# copy running-config startup-config
(Optional)

Saves this configuration change.

Example

Use the no feature rip command to disable the RIP feature and remove all associated configuration.

Command

Purpose

no feature rip

Example:

switch(config)# no feature rip

Disables the RIP feature and removes all associated configuration.

Creating a RIP Instance

You can create a RIP instance and configure the address family for that instance.

Before you begin

Ensure that you have enabled the RIP feature. See the Enabling the RIP Feature section.

SUMMARY STEPS

  1. configure terminal
  2. router rip instance-tag
  3. address-family ipv4 unicast
  4. (Optional) show ip rip [ instance instance-tag ] [ vrf vrf-name ]
  5. (Optional) copy running-config startup-config

DETAILED STEPS

  Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters configuration mode.

Step 2

router rip instance-tag

Example:

switch(config)# router RIP Enterprise
switch(config-router)#

Creates a new RIP instance with the configured instance-tag value .

Step 3

address-family ipv4 unicast

Example:

switch(config-router)# address-family ipv4 unicast
switch(config-router-af)#

Configures the address family for this RIP instance and enters address-family configuration mode.

Step 4

(Optional) show ip rip [ instance instance-tag ] [ vrf vrf-name ]

Example:

switch(config-router-af)# show ip rip
(Optional)

Displays a summary of RIP information for all RIP instances.

Step 5

(Optional) copy running-config startup-config

Example:

switch(config)# copy running-config startup-config
(Optional)

Saves this configuration change.

Example

Use the no router rip command to remove the RIP instance and the associated configuration.

Command

Purpose

no router rip instance-tag

Example:

switch(config)# no router rip Enterprise

Deletes the RIP instance and all associated configuration.


Note


You must also remove any RIP commands that are configured in interface mode.


You can configure the following optional parameters for RIP in address-family configuration mode:

Command

Purpose

distance value

Example:

switch(config-router-af)# distance 30

Sets the administrative distance for RIP. The range is from 1 to 255. The default is 120. See the Administrative Distance section.

maximum-paths number

Example:

switch(config-router-af)# maximum-paths 6

Configures the maximum number of equal-cost paths that RIP maintains in the route table. The range is from 1 to 32. The default is 16.

This example shows how to create a RIP instance for IPv4 and set the number of equal-cost paths for load balancing:

switch# configure terminal
switch(config)# router rip Enterprise
switch(config-router)# address-family ipv4 unicast
switch(config-router-af)# max-paths 10
switch(config-router-af)# copy running-config startup-config

Restarting a RIP Instance

You can restart a RIP instance. This clears all neighbors for the instance.

To restart an RIP instance and remove all associated neighbors, use the following command:

Command

Purpose

restart rip instance-tag

Example:

switch(config)# restart rip Enterprise

Restarts the RIP instance and removes all neighbors.

Configuring RIP on an Interface

You can add an interface to a RIP instance.

Before you begin

Ensure that you have enabled the RIP feature (see the Enabling the RIP Feature section).

SUMMARY STEPS

  1. configure terminal
  2. interface interface-type slot/port
  3. no switchport
  4. ip router rip instance-tag
  5. (Optional) show ip rip [ instance instance-tag ] interface [ interface-type slot/port ] [ vrf vrf-name ] [ detail ]
  6. (Optional) copy running-config startup-config

DETAILED STEPS

  Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters configuration mode.

Step 2

interface interface-type slot/port

Example:

switch(config)# interface ethernet 1/2
switch(config-if)#

Enters interface configuration mode.

Step 3

no switchport

Example:

switch(config-if)# no switchport

Configures the interface as a Layer 3 routed interface.

Step 4

ip router rip instance-tag

Example:

switch(config-if)# ip router rip Enterprise

Associates this interface with a RIP instance

Step 5

(Optional) show ip rip [ instance instance-tag ] interface [ interface-type slot/port ] [ vrf vrf-name ] [ detail ]

Example:

switch(config-if)# show ip rip Enterprise tethernet 1/2
(Optional)

Displays RIP information for an interface.

Step 6

(Optional) copy running-config startup-config

Example:

switch(config)# copy running-config startup-config
(Optional)

Saves this configuration change.

Example

This example shows how to add the Ethernet 1/2 interface to a RIP instance:

switch# configure terminal
switch(config)# interface ethernet 1/2
switch(config-if)# no switchport
switch(config-if)# ip router rip Enterprise
switch(config)# copy running-config startup-config

Restarting a RIP Instance

You can restart a RIP instance. This clears all neighbors for the instance.

To restart an RIP instance and remove all associated neighbors, use the following command:

Command

Purpose

restart rip instance-tag

Example:

switch(config)# restart rip Enterprise

Restarts the RIP instance and removes all neighbors.

Configuring RIP on an Interface

You can add an interface to a RIP instance.

Before you begin

Ensure that you have enabled the RIP feature (see the Enabling the RIP Feature section).

SUMMARY STEPS

  1. configure terminal
  2. interface interface-type slot/port
  3. no switchport
  4. ip router rip instance-tag
  5. (Optional) show ip rip [ instance instance-tag ] interface [ interface-type slot/port ] [ vrf vrf-name ] [ detail ]
  6. (Optional) copy running-config startup-config

DETAILED STEPS

  Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters configuration mode.

Step 2

interface interface-type slot/port

Example:

switch(config)# interface ethernet 1/2
switch(config-if)#

Enters interface configuration mode.

Step 3

no switchport

Example:

switch(config-if)# no switchport

Configures the interface as a Layer 3 routed interface.

Step 4

ip router rip instance-tag

Example:

switch(config-if)# ip router rip Enterprise

Associates this interface with a RIP instance

Step 5

(Optional) show ip rip [ instance instance-tag ] interface [ interface-type slot/port ] [ vrf vrf-name ] [ detail ]

Example:

switch(config-if)# show ip rip Enterprise tethernet 1/2
(Optional)

Displays RIP information for an interface.

Step 6

(Optional) copy running-config startup-config

Example:

switch(config)# copy running-config startup-config
(Optional)

Saves this configuration change.

Example

This example shows how to add the Ethernet 1/2 interface to a RIP instance:

switch# configure terminal
switch(config)# interface ethernet 1/2
switch(config-if)# no switchport
switch(config-if)# ip router rip Enterprise
switch(config)# copy running-config startup-config

Configuring RIP Authentication

Before you begin

Ensure that you have enabled the RIP feature (see the Enabling the RIP Feature section).

Configure a key chain if necessary before enabling authentication. See the Cisco Nexus 3548 Switch NX-OS Security Configuration Guide for details on implementing key chains.

SUMMARY STEPS

  1. configure terminal
  2. interface interface-type slot/port
  3. no switchport
  4. ip rip authentication mode { text | md5 }
  5. ip rip authentication key-chain key
  6. (Optional) copy running-config startup-config

DETAILED STEPS

  Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters configuration mode.

Step 2

interface interface-type slot/port

Example:

switch(config)# interface ethernet 1/2
switch(config-if)#

Enters interface configuration mode.

Step 3

no switchport

Example:

switch(config-if)# no switchport

Configures the interface as a Layer 3 routed interface.

Step 4

ip rip authentication mode { text | md5 }

Example:

switch(config-if)# ip rip authentication mode md5

Sets the authentication type for RIP on this interface as cleartext or MD5 authentication digest.

Step 5

ip rip authentication key-chain key

Example:

switch(config-if)# ip rip authentication keychain RIPKey

Configures the authentication key used for RIP on this interface.

Step 6

(Optional) copy running-config startup-config

Example:

switch(config)# copy running-config startup-config
(Optional)

Saves this configuration change.

Example

This example shows how to create a key chain and configure MD5 authentication on a RIP interface:

switch# configure terminal
switch(config)# key chain RIPKey
switch(config)# key-string myrip
switch(config)# accept-lifetime 00:00:00 Jan 01 2000 infinite
switch(config)# send-lifetime 00:00:00 Jan 01 2000 infinite
switch(config)# interface ethernet 1/2
switch(config-if)# no switchport
switch(config-if)# ip rip authentication mode md5
switch(config-if)# ip rip authentication keychain RIPKey
switch(config-if)# copy running-config startup-config

Configuring a Passive Interface

You can configure a RIP interface to receive routes but not send route updates by setting the interface to passive mode.

To configure a RIP interface in passive mode, use the following command in interface configuration mode:

Command

Purpose

ip rip passive-interface

Example :

switch(config-if)# ip rip passive-interface

Sets the interface into passive mode.

Configuring Split Horizon with Poison Reverse

You can configure an interface to advertise routes learned by RIP as unreachable over the interface that learned the routes by enabling poison reverse.

To configure split horizon with poison reverse on an interface, use the following command in interface configuration mode:

Command

Purpose

ip rip poison-reverse

Example :

switch(config-if)# ip rip poison-reverse

Enables split horizon with poison reverse. Split horizon with poison reverse is disabled by default.

Configuring Route Summarization

You can create aggregate addresses that are represented in the routing table by a summary address. Cisco NX-OS advertises the summary address metric that is the smallest metric of all the more-specific routes.

To configure a summary address on an interface, use the following command in interface configuration mode:

Command

Purpose

ip rip summary-address ip-prefix/mask-len

Example :

switch(config-if)# ip router rip summary-address 192.0.2.0/24

Configures a summary address for RIP for IPv4 addresses.

Configuring Route Redistribution

You can configure RIP to accept routing information from another routing protocol and redistribute that information through the RIP network. Redistributed routes can optionally be assigned a default route.

Before you begin

Ensure that you have enabled the RIP feature (see the Enabling the RIP Feature section).

Configure a route map before configuring redistribution. See the Configuring Route Maps section for details on configuring route maps.

SUMMARY STEPS

  1. configure terminal
  2. router rip instance-tag
  3. address-family ipv4 unicast
  4. redistribute { bgp as | direct | eigrp | ospf | ospfv3 | rip } instance-tag | static } route-map map-name
  5. (Optional) default-information originate [ always ] [ route-map map-name ]
  6. (Optional) default-metric value
  7. (Optional) show ip rip route [ ip-prefix [ longer-prefixes | shorter-prefixes ] [ vrf vrf-name] [summary ]
  8. (Optional) copy running-config startup-config

DETAILED STEPS

  Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters configuration mode.

Step 2

router rip instance-tag

Example:

switch(config)# router RIP Enterprise
switch(config-router)#

Creates a new RIP instance with the configured instance-tag value .

Step 3

address-family ipv4 unicast

Example:

switch(config-router)# address-family ipv4 unicast
switch(config-router-af)#

Configures the address family for this RIP instance and enters address-family configuration mode.

Step 4

redistribute { bgp as | direct | eigrp | ospf | ospfv3 | rip } instance-tag | static } route-map map-name

Example:

switch(config-router-af)# redistribute eigrp 201 route-map RIPmap

Redistributes routes from other protocols into RIP. See the Configuring Route Maps section for more information about route maps.

Step 5

(Optional) default-information originate [ always ] [ route-map map-name ]

Example:

switch(config-router-af)# default-information originate always
(Optional)

Generates a default route into RIP, optionally controlled by a route map.

Step 6

(Optional) default-metric value

Example:

switch(config-router-af)# default-metric 10
(Optional)

Sets the default metric for all redistributed routes. The range is from 1 to 15. The default is 1.

Step 7

(Optional) show ip rip route [ ip-prefix [ longer-prefixes | shorter-prefixes ] [ vrf vrf-name] [summary ]

Example:

switch(config-router-af)# show ip rip route
(Optional)

Shows the routes in RIP.

Step 8

(Optional) copy running-config startup-config

Example:

switch(config)# copy running-config startup-config
(Optional)

Saves this configuration change.

Example

This example shows how to redistribute EIGRP into RIP:

switch# configure terminal
switch(config)# router rip Enterprise
switch(config-router)# address-family ipv4 unicast
switch(config-router-af)# redistribute eigrp 201 route-map RIPmap
switch(config-router-af)# copy running-config startup-config

Configuring Virtualization

You can create multiple VRFs and use the same or multiple RIP instances in each VRF. You assign a RIP interface to a VRF.


Note


Configure all other parameters for an interface after you configure the VRF for an interface. Configuring a VRF for an interface deletes all the configuration for that interface.


Before you begin

Ensure that you have enabled the RIP feature (see the Enabling the RIP Feature section).

SUMMARY STEPS

  1. configure terminal
  2. vrf vrf-name
  3. exit
  4. router rip instance-tag
  5. vrf context vrf-name
  6. (Optional) address-family ipv4 unicast
  7. (Optional) redistribute { bgp as | direct | eigrp | ospf | ospfv3 | rip } instance-tag | static } route-map map-name
  8. interface ethernet slot/port
  9. no switchport
  10. vrf member vrf-name
  11. ip address ip-prefix/length
  12. ip router rip instance-tag
  13. (Optional) show ip rip route [ ip-prefix [ longer-prefixes | shorter-prefixes ] [ vrf vrf-name] [summary ]
  14. (Optional) copy running-config startup-config

DETAILED STEPS

  Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters configuration mode.

Step 2

vrf vrf-name

Example:

switch(config)# vrf RemoteOfficeVRF
switch(config-vrf)#

Creates a new VRF.

Step 3

exit

Example:

switch(config-vrf)# exit
switch(config)#

Exits VRF configuration mode.

Step 4

router rip instance-tag

Example:

switch(config)# router RIP Enterprise
switch(config-router)#

Creates a new RIP instance with the configured instance-tag value .

Step 5

vrf context vrf-name

Example:

switch(config)# vrf context RemoteOfficeVRF
switch(config-vrf)#

Creates a new VRF and enters VRF configuration mode.

Step 6

(Optional) address-family ipv4 unicast

Example:

switch(config-router)# address-family ipv4 unicast
switch(config-router-af)#
(Optional)

Configures the VRF address family for this RIP instance.

Step 7

(Optional) redistribute { bgp as | direct | eigrp | ospf | ospfv3 | rip } instance-tag | static } route-map map-name

Example:

switch(config-router-af)# redistribute eigrp 201 route-map RIPmap
(Optional)

Redistributes routes from other protocols into RIP. See the Configuring Route Maps section for more information about route maps.

Step 8

interface ethernet slot/port

Example:

switch(config-router-vrf-af)# interface ethernet 1/2
switch(config-if)#

Enters interface configuration mode.

Step 9

no switchport

Example:

switch(config-if)# no switchport

Configures the interface as a Layer 3 routed interface.

Step 10

vrf member vrf-name

Example:

switch(config-if)# vrf member RemoteOfficeVRF

Adds this interface to a VRF.

Step 11

ip address ip-prefix/length

Example:

switch(config-if)# ip address 192.0.2.1/16

Configures an IP address for this interface. You must do this step after you assign this interface to a VRF.

Step 12

ip router rip instance-tag

Example:

switch(config-if)# ip router rip Enterprise

Associates this interface with a RIP instance.

Step 13

(Optional) show ip rip route [ ip-prefix [ longer-prefixes | shorter-prefixes ] [ vrf vrf-name] [summary ]

Example:

switch(config-router-af)# show ip rip route
(Optional)

Shows the routes in RIP.

Step 14

(Optional) copy running-config startup-config

Example:

switch(config)# copy running-config startup-config
(Optional)

Saves this configuration change.

Example

This example shows how to create a VRF and add an interface to the VRF:

switch# configure terminal
switch(config)# vrf context RemoteOfficeVRF
switch(config-vrf)# exit
switch(config)# router rip Enterprise
switch(config-router)# vrf RemoteOfficeVRF
switch(config-router-vrf)# address-family ipv4 unicast
switch(config-router-vrf-af)# redistribute eigrp 201 route-map RIPmap
switch(config-router-vrf-af)# interface ethernet 1/2
switch(config-if)# no switchport
switch(config-if)# vrf member RemoteOfficeVRF
switch(config-if)# ip address 192.0.2.1/16
switch(config-if)# ip router rip Enterprise
switch(config-if)# copy running-config startup-config

Tuning RIP

You can tune RIP to match your network requirements. RIP uses several timers that determine the frequency of routing updates, the length of time before a route becomes invalid, and other parameters. You can adjust these timers to tune routing protocol performance to better suit your internetwork needs.


Note


You must configure the same values for the RIP timers on all RIP-enabled routers in your network.


You can use the following optional commands in address-family configuration mode to tune RIP:

Command

Purpose

timers basic update timeout holddown garbage-collection

Example:

switch(config-router-af)# timers basic 40 120 120 100

Sets the RIP timers in seconds. The parameters are as follows:

  • update—The range is from 5 to any positive integer. The default is 30.

  • timeout—The time that Cisco NX-OS waits before declaring a route as invalid. If Cisco NX-OS does not receive route update information for this route before the timeout interval ends, Cisco NX-OS declares the route as invalid. The range is from 1 to any positive integer. The default is 180.

  • holddown—The time during which Cisco NX-OS ignores better route information for an invalid route. The range is from 0 to any positive integer. The default is 180.

  • garbage-collection—The time from when Cisco NX-OS marks a route as invalid until Cisco NX-OS removes the route from the routing table. The range is from 1 to any positive integer. The default is 120.

You can use the following optional commands in interface configuration mode to tune RIP:

Command

Purpose

ip rip metric-offset value

Example :

switch(config-if)# ip rip metric-offset 10

Adds a value to the metric for every router received on this interface. The range is from 1 to 15. The default is 1.

ip rip route-filter {prefix-list list-name | route-map map-name | [ in | out ]}

Example :

switch(config-if)# ip rip route-filter route-map InputMap in

Specifies a route map to filter incoming or outgoing RIP updates.

Verifying the RIP Configuration

To display the RIP configuration information, perform one of the following tasks:

Command

Purpose

show ip rip instance [instance-tag] [vrf vrf-name]

Displays the status for an instance of RIP.

show ip rip [instance instance-tag] interface slot/port detail [vrf vrf-name]

Displays the RIP status for an interface.

show ip rip [instance instance-tag] neighbor [interface-type number] [vrf vrf-name]

Displays the RIP neighbor table.

show ip rip [instance instance-tag] route [ip-prefix/lengh [longer-prefixes | shorter--prefixes]] [summary] [vrf vrf-name]

Displays the RIP route table.

show running-configuration rip

Displays the current running RIP configuration.

Displaying RIP Statistics

To display the RIP statistics, use the following commands:

Command

Purpose

show ip rip [instance instance-tag] policy statistics redistribute { bgp as | direct | { eigrp | ospf | ospfv3 | rip } instance-tag | static} [vrf vrf-name]

Displays the RIP policy status.

show ip rip [instance instance-tag] statistics interface-type number] [vrf vrf-name]

Displays the RIP statistics.

Use the clear ip rip policy command to clear policy statistics.

Use the clear ip rip statistics command to clear RIP statistics.

Configuration Examples for RIP

This example creates the Enterprise RIP instance in a VRF and adds Ethernet interface 1/2 to this RIP instance. The example also configures authentication for Ethernet interface 1/2 and redistributes EIGRP into this RIP domain.

vrf context NewVRF

!

feature rip

router rip Enterprise

vrf NewVRF

address-family ip unicast

redistribute eigrp 201 route-map RIPmap

max-paths 10

!

interface ethernet 1/2

no switchport

vrf NewVRF

ip address 192.0.2.1/16

ip router rip Enterprise

ip rip authentication mode md5

ip rip authentication keychain RIPKey