Configuring LLDP

Configuring LLDP

Before you begin

Ensure that the Link Layer Discovery Protocol (LLDP) feature is enabled on the switch.

SUMMARY STEPS

  1. switch# configure terminal
  2. switch# feature lldp
  3. switch(config)# lldp {holdtime seconds | reinit seconds | timer seconds | tlv-select {dcbxp | management-address | power management | port-description | port-vlan | system-capabilities | system-description | system-name}}
  4. switch(config)# no lldp {holdtime | reinit | timer}
  5. (Optional)switch# show lldp

DETAILED STEPS

  Command or Action Purpose

Step 1

switch# configure terminal

Enters global configuration mode.

Step 2

switch# feature lldp

Enable LLDP.

Step 3

switch(config)# lldp {holdtime seconds | reinit seconds | timer seconds | tlv-select {dcbxp | management-address | power management | port-description | port-vlan | system-capabilities | system-description | system-name}}

Configures LLDP options.

Use the holdtime option to set the length of time (10 to 255 seconds) that a device should save LLDP information received before discarding it. The default value is 120 seconds.

Use the reinit option to set the length of time (1 to 10 seconds) to wait before performing LLDP initialization on any interface. The default value is 2 seconds.

Use the timer option to set the rate (5 to 254 seconds) at which LLDP packets are sent. The default value is 30 seconds.

Use the tlv-select option to specify the type length value (TLV). The default is enabled to send and receive all TLVs.

Use the dcbxp option to specify the Data Center Ethernet Parameter Exchange (DCBXP) TLV messages.

Use the management-address option to specify the management address TLV messages.

Use the power management option to specify the power management TLV for LLDP.

Use the port-description option to specify the port description TLV messages.

Use the port-vlan option to specify the port VLAN ID TLV messages.

Use the system-capabilities option to specify the system capabilities TLV messages.

Use the system-description option to specify the system description TLV messages.

Use the system-name option to specify the system name TLV messages.

Step 4

switch(config)# no lldp {holdtime | reinit | timer}

Resets the LLDP values to their defaults.

Step 5

(Optional)switch# show lldp

Displays LLDP configurations.

Example

This example shows how to configure the global LLDP hold time to 200 seconds: 

switch# configure terminal
switch(config)# lldp holdtime 200
switch(config)#

This example shows how to enable LLDP to send or receive the management address TLVs: 

switch# configure terminal
switch(config)# lldp tlv-select management-address
switch(config)#

Configuring Interface LLDP

SUMMARY STEPS

  1. switch# configure terminal
  2. switch(config)# interface type slot/port
  3. switch(config-if)# [no] lldp {receive | transmit}
  4. (Optional) switch# show lldp {interface | neighbors [detail | interface | system-detail] | timers | traffic}

DETAILED STEPS

  Command or Action Purpose

Step 1

switch# configure terminal

Enters global configuration mode.

Step 2

switch(config)# interface type slot/port

Selects the interface to change.

Step 3

switch(config-if)# [no] lldp {receive | transmit}

Sets the selected interface to either receive or transmit.

The no form of the command disables the LLDP transmit or receive.

Step 4

(Optional) switch# show lldp {interface | neighbors [detail | interface | system-detail] | timers | traffic}

(Optional)

Displays LLDP configurations.

Example

This example shows how to set an interface to transmit LLDP packets: 

switch# configure terminal
switch(config)# interface ethernet 1/2
switch(config-if)# lldp transmit

This example shows how to configure an interface to disable LLDP: 

switch# configure terminal
switch(config)# interface ethernet 1/2
switch(config-if)# no lldp transmit
switch(config-if)# no lldp receive

This example shows how to display LLDP interface information: 

switch# show lldp interface ethernet 1/2
tx_enabled: TRUE
rx_enabled: TRUE
dcbx_enabled: TRUE
Port MAC address:    00:0d:ec:a3:5f:48
Remote Peers Information
No remote peers exist

This example shows how to display LLDP neighbor information: 

switch# show lldp neighbors
Capability codes:
  (R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device
  (W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other
Device ID            Local Intf      Hold-time  Capability  Port ID  
SW-INSBU-JWALA-PP52.cisco.com
                     mgmt0           120        B           Gi1/0/37      
MTC-2                Eth1/41         120        BR          Ethernet1/43  
MTC-CR2              Eth1/42         120        BR          Ethernet1/43  
MTC-CR2              Eth1/43         120        BR          Ethernet1/42  
MTC-2                Eth1/44         120        BR          Ethernet1/41  
MTC-CR2              Eth1/45         120        BR          Ethernet1/41  
MTC-2                Eth1/46         120        BR          Ethernet1/44  
MTC-2                Eth1/47         120        BR          Ethernet1/42  
MTC-CR2              Eth1/48         120        BR          Ethernet1/44  
Total entries displayed: 9

This example shows how to display the system details about LLDP neighbors: 

switch# sh lldp neighbors system-detail
Capability codes:
	(R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device
	(W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other
Device ID	Local Intf	Chassis ID	PortID	Hold-time	Capability

switch-2		Eth1/7		0005.73b7.37ce	Eth1/7		120	B
switch-3		Eth/9			0005.73b7.37d0	Eth1/9		120	B
switch-4		Eth1/10	0005.73b7.37d1	Eth1/10	120	B
Total entries displayed: 3

This example shows how to display LLDP timer information: 

switch# show lldp timers
LLDP Timers
holdtime 120 seconds
reinit 2 seconds
msg_tx_interval 30 seconds

This example shows how to display information about LLDP counters: 

switch# show lldp traffic
LLDP traffic statistics:
 
    Total frames out: 8464
    Total Entries aged: 6
    Total frames in: 6342
    Total frames received in error: 2
    Total frames discarded: 2
    Total TLVs unrecognized: 0