Configuring ITD
About ITD
Licensing Requirements
Supported Platforms
Guidelines and Limitations for ITD
ITD Support Summary
Default Settings for ITD
Configuring ITD
Verifying the ITD Layer-3 Configuration
Configuration Examples for ITD
Related Documents

Configuring ITD

This chapter describes how to configure the Intelligent Traffic Director (ITD) on the Cisco NX-OS device.

About ITD

Intelligent Traffic Director (ITD) is an intelligent, hardware-based, multi-terabit solution that allows you to build a scalable architecture for Layer 3 and Layer 4 traffic distribution, load balancing, and redirection.

Benefits of ITD:

Multi-terabit solution at line rate
Transparency to end device and stateless protocol benefits
Reduced complexities and architecture scaling for alternative features like Web Cache Communication Protocol (WCCP) and policy-based routing
Simplified provisioning and ease of deployment
Legacy service appliances can co-exist with new ones
Removes the requirement for an expensive external load balancer
No certification, integration, or qualification needed between the devices and the Cisco NX-OS switch
Order of magnitude OPEX savings : reduction in configuration, and ease of deployment
CAPEX savings : No service module or external L3/L4 load-balancer needed. Every Nexus port can be used as load-balancer

ITD features:

Hardware based multi-terabit/s L3/L4 load-balancing at wire-speed
Zero latency load-balancing
Redirect line-rate traffic to any devices, for example web cache engines, Web Accelerator Engines (WAE), video-caches, etc
Capability to create clusters of devices, for example, Firewalls, Intrusion Prevention System (IPS), or Web Application Firewall (WAF), Hadoop cluster
IP-stickiness
Hardware based multi-terabit/s L3/L4 load-balancing at wire-speed
Zero latency load-balancing
Redirect line-rate traffic to any devices, for example web cache engines, Web Accelerator Engines (WAE), video-caches, etc
Capability to create clusters of devices, for example, Firewalls, Intrusion Prevention System (IPS), or Web Application Firewall (WAF), Hadoop cluster
IP-stickiness
Resilient (like resilient ECMP), Consistent hash
Virtual IP based L4 load-balancing
Weighted load-balancing and Failaction are supported among nodes
Load-balances to large number of devices/servers
ACL along with redirection and load balancing simultaneously
Bi-directional flow-coherency. Traffic from A–>B and B–>A goes to same node
The servers/appliances don’t have to be directly connected to Nexus switch
Monitoring the health of servers/appliances with IP SLA-based probes
N + M redundancy (N number of nodes and M number of hot-standbys)
Automatic failure handling of servers/appliances
VRF support, vPC support
Supports both IPv4 and IPv6 (all platforms do not support IPv6)
The feature does not add any load to the supervisor CPU
Handles unlimited number of flows
Nondisruptive node addition or deletion
Simultaneous redirection and load balancing
Rate sharing across multiple ITD services in the same switch

Use case examples:

Load-balance to cluster of Firewalls.
Scale IPS, IDS and WAF by load-balancing to standalone devices
Scale the NFV solution by load-balancing to low cost VM/container based NFV
Scale the WAAS / WAE solution. Traffic redirection mechanism for the Wide Area Application Services (WAAS) or Web Accelerator Engine (WAE) solution
Scale the VDS-TC (video-caching) solution
Scale Layer-7 load-balancers, by distributing traffic to L7 LBs
Replaces ECMP or the port channel to avoid rehashing . ITD is resilient, and doesn’t cause re-hashing on node add/delete/failure
Server load balancing in DSR (Direct Server Return) mode
Scales up NG intrusion prevention systems (IPSs) and web application firewalls (WAFs) by load balancing to standalone devices
Load balances to Layer 5 through Layer 7 load balancers

Deployment Modes

One-Arm Deployment Mode

You can connect servers to the switch in one-arm deployment mode. In this topology, the server is not in the direct path of client or server traffic, which enables you to plug a server into the network with no changes to the existing topology or network.

Server Load-Balancing Deployment Mode

The ITD service can be configured to host a virtual IP (VIP) on the switch. Internet traffic destined for the VIP will be load balanced to the active nodes. The ITD service is not a stateful load balancer.

Note

You need to configure the ITD service manually and in a similar manner on each switch.

Figure 2. ITD Load Distribution with VIP

Device Groups

Nodes can be a physical server, virtual server, or a service appliance where traffic can be load balanced. These nodes are grouped together under a device group, and this device group can be mapped to a service.

ITD supports device groups. When you configure a device group, you can specify the following:

The device group's nodes
The device group's probe

You can configure probes at the device-group level or at the node level. With node-level probing, each node can be configured with its own probe, allowing for further customization per node. Node-level probes are useful in scenarios where each node needs to be monitored differently for failure conditions.

Multiple Device Groups in an ITD Service

device groups are supported in an ITD service (as shown in the figure below). An ITD service generates a single route map with different sequences that point to different device groups.

Each device group represents different types of traffic requiring different services but arriving on the same ingress interface. Traffic on the interface is redirected to the appropriate device group based on the virtual IP address. Supporting multiple device groups per ITD service on the same interface allows ITD to scale.

Figure 3. Multiple Device Groups in an ITD Service

For a configuration example showing how to configure multiple device groups in an ITD service, see .

VRF Support

The ITD service can be configured in the default VRF as well as in non-default VRFs.

Ingress interfaces and device-group nodes must all belong to the same VRF for the ITD service to redirect traffic. You must ensure that all ingress interfaces and node members of the associated device group are reachable in the configured VRF.

Include and Exclude ACLs

Include ACL

The include ACL feature allows you to assign an access control list (ACL) to an ITD service. Only traffic matching the ACE is load-balanced toward the nodes and other traffic follows default routing rules.

You can configure up to 8 access-lists under one ITD service. You can associate each access list with its own device-group (Multi-ACL). When specific device-group is associated with one user ACL, that device-group takes priority and overwrites the default device-group. With this feature, ITD can load-balance traffic matching different ACLs to different device-groups.

Exclude ACL

You can configure an exclude ACL to specify the traffic that you want ITD to exclude from the ITD load balancer. The traffic, which the exclude ACL selects, is RIB-routed and bypasses ITD. An exclude ACL can filter based on both source and destination fields. The exclude ACL precedes the virtual IP address.

Virtual IP Address Filtering

A virtual IP address can be used to filter traffic for ITD. A virtual IP address and subnet mask combination for traffic filtering is supported for the destination field only.

Port Number-Based Filtering

Port numbering can be used to filter traffic for ITD. The following methods are supported to filter traffic based on Layer 4 ports (for example, port 80):

Matching destination ports

Any source or destination IP address with destination port 80 is matched. (For example: The virtual IP address is configured as 0.0.0.0 0.0.0.0 tcp 80.)
Matching source ports

Any port other than 80 bypasses ITD, and port 80 is redirected. (For example: The exclude ACL is configured as permit tcp any neq 80 any.)
Matching multiple port numbers

Multiple virtual IP address lines in ITD can be configured, one for each port.

Hot-Standby

The hot-standby feature reconfigures the switch to look for an operational hot-standby node and select the first available hot-standby node to replace the failed node. ITD reconfigures the switch to redirect the traffic segment that was originally headed toward the failed node to the hot-standby node. The service does not impose any fixed mapping of hot-standby nodes to active nodes.

When the failed node becomes operational again, it is reinstated as an active node. The traffic from the acting hot-standby node is redirected back to the original node, and the hot-standby node reverts to the pool of standby nodes.

When multiple nodes fail, traffic destined to all failed nodes gets redirected to the first available hot-standby node.

The hot-standby node can be configured only at the node level . At the node level, the hot-standby node receives traffic only if its associated active node fails.

ITD supports N + M redundancy where M nodes can act as hot-standby nodes for N active nodes.

Multiple Ingress Interfaces

You can configure the ITD service to apply traffic redirection policies on multiple ingress interfaces. This feature allows you to use a single ITD service to redirect traffic arriving on different interfaces to a group of nodes.

System Health Monitoring

ITD monitors health of the nodes and applications running on those nodes periodically to detect any failures and to handle the failure scenarios.

ICMP, TCP, UDP probes are supported.

Health of an Interface Connected to a Node

leverages the IP service level agreement (IP SLA) feature to periodically probe each node. ITD uses the Internet Control Message Protocol (ICMP) to periodically probe each node. The probes are sent at a 10-second frequency by default and can be configured down to 1 second. They are sent simultaneously to all nodes. You can configure the probe as part of the pool group configuration.

A probe is declared to have failed after retrying three times by default. At this point, the node state becomes “Failed,” and its status becomes “PROBE_FAILED.”

Node Failure Handling

Upon marking a node as down, the ITD performs the following tasks automatically to minimize traffic disruption and to redistribute the traffic to remaining operational nodes:

Determines if a standby node is configured to take over from the failed node.
If the standby node is operational, it is identified the node as a candidate node for traffic handling.
Redefines the standby node as active for traffic handling, if an operational standby node is available
Programs automatically to reassign traffic from the failed node to the newly active standby node.

Failaction Reassignment

Failaction for ITD enables traffic to the failed nodes to be reassigned to one or more active nodes. When the failed node becomes active again, it resumes serving connections. If all the nodes are down, the packets are routed automatically. All Failaction mechanisms are supported for both IPv4 and IPv6 services.

Note

You must configure a probe under an ITD device group before enabling the failaction feature.

Failaction Node Reassign

When a node goes down, the traffic buckets associated with the node are reassigned to the first active node found in the configured set of nodes. If the newly reassigned node also fails, traffic is reassigned to the next available active node.

Failaction Node Least-Bucket

When a node goes down, the traffic buckets associated with the node are reassigned to an active node that is currently receiving traffic from the least number of traffic buckets. For each subsequent node failure, the active node with least traffic buckets is recomputed and all the buckets directed to a failed node are redirected to this node, thereby allowing the re-assigned buckets to be distributed over multiple active nodes.

Failaction Bucket Distribute

When the service is enabled, ITD uses an internal algorithm to preselect varied sequences of primary nodes as alternate backup paths for with different priorities for each primary node. When a node goes down, the traffic to the node will be re-directed to the first active backup node with the highest priority, and so on, for subsequent failures, thereby minimizing the convergence delays.

the primary nodes of a device-group or up to 32 primary nodes of a device-group (whichever is lesser) shall be preselected with different priorities for each node.

Note

This algorithm is intended for relatively even traffic distribution but doesn't guarantee even distribution with node failures.

Failaction Node-Per-Bucket

When a particular node fails, the node with least number of buckets are identified and the buckets are distributed across the other active nodes, starting from the node with least buckets.

ITD repeatedly identifies the least buckets node currently and assign one bucket to the node until all buckets are reassigned. Hence all buckets are distributed evenly among all remaining active nodes.

Note

identifies the nodes to fail-over, based on the weights of the nodes. If a node doesn't have a weight configured a default weight of 1 is used.

No Failaction Reassignment

When failaction node reassignment is not configured, there are two possible scenarios:

No Failaction Reassignment with a Probe Configured

The ITD probe can detect the node failure or the lack of service reachability. If the node fails, the traffic is routed and does not get reassigned, as failaction is not configured. Once the node recovers, the recovered node starts to handle the traffic.

No Failaction Reassignment without a Probe Configured

Without a probe configuration, ITD cannot detect the node failure. When the node is down, ITD does not reassign or redirect the traffic to an active node.

Licensing Requirements

For a complete explanation of Cisco NX-OS licensing recommendations and how to obtain and apply licenses, see the Cisco NX-OS Licensing Guide.

Supported Platforms

Starting with Cisco NX-OS release 7.0(3)I7(1), use the Nexus Switch Platform Support Matrix to know from which Cisco NX-OS releases various Cisco Nexus 9000 and 3000 switches support a selected feature.

Guidelines and Limitations for ITD

ITD has the following configuration guidelines and limitations:

ITD Support Summary

See the following table for a list of the ITD support levels.

Table 1. ITD support levels
Feature	ITDv4	ITDv6	Comments
Device group level	TCP ICMP UDP	TCP ICMPv3	Introduced in Cisco NX-OS Release 10.1(1)
Per Node-Probe Level	Yes	Yes	Introduced in Cisco NX-OS Release 10.1(1)
Hot-Standby	Yes	Yes	Introduced in Cisco NX-OS Release 10.1(1)
Weight	Yes	Yes	Introduced in Cisco NX-OS Release 10.1(1)
Non-Disruptive Operation
ACL Refresh	Yes	Yes	Introduced in Cisco NX-OS Release 10.1(1)
Primary Nodes	Yes	Yes	Introduced in Cisco NX-OS Release 10.1(1)
Hot Standby Nodes	No	No	Introduced in Cisco NX-OS Release 10.1(1)
Service-Level
Include ACL	Yes	Yes	Introduced in Cisco NX-OS Release 10.1(1)
Failaction methods	reassign least-bucket node-per-bucket bucket distribute	reassign least-bucket node-per-bucket bucket distribute	Introduced in Cisco NX-OS Release 10.1(1)
Exclude-ACL	Yes	Yes	Introduced in Cisco NX-OS Release 10.1(1) The deny ACEs are not supported.
Supported Platforms	Cisco Nexus C36180YC-R and C3636C-R switches	Cisco Nexus C36180YC-R and C3636C-R switches	Introduced in Cisco NX-OS Release 10.1(1)

Default Settings for ITD

This table lists the default settings for ITD parameters.

Table 2. Default ITD Parameters
Parameters	Default
Probe frequency	10 seconds
Probe retry down count	3
Probe retry up count	3
Probe timeout	5 seconds

Configuring ITD

Enabling ITD

Before you can access the ITD commands, you must enable the ITD feature.

Before you begin

Ensure that you have installed the Network Services license.

Ensure that policy-based routing (PBR) is enabled.

SUMMARY STEPS

configure terminal
[no] feature itd
(Optional) copy running-config startup-config

DETAILED STEPS

Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters global configuration mode.

Step 2

[no] feature itd

Example:

switch(config)# feature itd

Enables the ITD feature. By default, ITD is disabled.

Step 3

(Optional) copy running-config startup-config

Example:

switch(config)# copy running-config startup-config

(Optional)

Copies the running configuration to the startup configuration.

Configuring a Device Group

You can create an ITD device group and then specify the group's nodes and probe. can configure multiple device groups.

Before you begin

Ensure that the ITD feature is enabled.

that the following commands are configured: feature sla sender and feature sla responder .

SUMMARY STEPS

configure terminal
[no] itd device-group name
[no] node {ip | ipv6} {ipv4-address | ipv6-address}
[no] weight weight
[no] mode hot-standby
exit
Repeat Steps 3 through 5 for each node.
[no] probe {icmp | http | tcp port port-number | udp port port-number | dns [frequency seconds] [[retry-down-count | retry-up-count] number] [timeout seconds]
(Optional) copy running-config startup-config

DETAILED STEPS

	Command or Action	Purpose
Step 1	configure terminal Example: `switch# configure terminal switch(config)#`	Enters global configuration mode.
Step 2	[no] itd device-group `name` Example: `switch(config)# itd device-group dg1 switch(config-device-group)#`	Creates an ITD device group and enters device group configuration mode. You can enter up to 32 alphanumeric characters.
Step 3	[no] node {ip \| ipv6} {`ipv4-address` \| `ipv6-address`} Example: `switch(config-device-group)# node ip 20.20.20.3 switch(config-dg-node)#` Example: `switch(config-device-group)# node ipv6 2001::198:1:1:11 switch(config-dg-node)#`	Specifies the nodes for ITD.
Step 4	[no] weight `weight` Example: `switch(config-dg-node)# weight 6`	Specifies the weight of the node for ITD. The range is from 1 to 256.
Step 5	[no] mode hot-standby Example: `switch (config-device-group)# node ipv6 50::1 switch(config-device-group-node)# mode hot-standby`	Configures the node as a hot-standby node for the device group.
Step 6	exit Example: `switch(config-dg-node)# exit switch(config-device-group)#`	Exits device group node configuration mode.
Step 7	Repeat Steps 3 through 5 for each node.
Step 8	[no] probe {icmp \| http \| tcp port `port-number` \| udp port `port-number` \| dns [frequency `seconds`] [[retry-down-count \| retry-up-count] `number`] [timeout `seconds`] Example: `switch(config-device-group)# probe icmp frequency 100`	Configures the cluster group service probe. can specify the following protocols as the probe for the ITD service: ICMP TCP UDP The options are as follows: frequency —Specifies the frequency of the probe in seconds. The range is from 1 to 604800. retry-down-count —Specifies the number of recounts undertaken by the probe when the node goes down. The range is from 1 to 5. retry-up-count —Specifies the number of recounts undertaken by the probe when the node comes back up. The range is from 1 to 5. timeout —Specifies the length of the timeout period in seconds. The range is from 1 to 604800.
Step 9	(Optional) copy running-config startup-config Example: `switch(config-device-group)# copy running-config startup-config`	(Optional) Copies the running configuration to the startup configuration.

Configuring an ITD Service

Before you begin

Ensure that the ITD feature is enabled.

Ensure that the device group to be added to the ITD service has been configured.

SUMMARY STEPS

configure terminal
[no] itd service-name
[no] device-group device-group-name
[no] ingress interface interface
[no] load-balance {method {src {ip | ip-l4port [tcp | udp] range x y} | dst {ip | ip-l4port [tcp | udp] range x y}} | buckets bucket-number | mask-position mask-position | }
[no] virtual [ ip | ipv6 ] { ipv4-address ipv4-network-mask | ipv6-address ipv6-network-mask }[ { proto {port_num | port_any}}] [ {advertise} {enable | disable}] [device-group dgrp_name]
Enter one of the following commands to determine how traffic is reassigned after a node failure:

[no] failaction node reassign
[no] failaction node least-bucket
[no] failaction bucket distribute
[no] failaction node per-bucket

[no] vrf vrf-name
[no] exclude access-list acl-name
no shutdown
(Optional) show itd [itd-name]
(Optional) copy running-config startup-config

DETAILED STEPS

Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters global configuration mode.

Step 2

[no] itd service-name

Example:

switch(config)# itd service1
switch(config-itd)#

Configures an ITD service and enters ITD configuration mode. You can enter up to 32 alphanumeric characters.

Step 3

[no] device-group device-group-name

Example:

switch(config-itd)# device-group dg1

Adds an existing device group to the ITD service. The device-group-name specifies the name of the device group. You can enter up to 32 alphanumeric characters.

Note

You can add multiple device groups to the ITD service.

Step 4

[no] ingress interface interface

Example:

switch(config-itd)# ingress interface ethernet 4/1-10

Adds an ingress interface or multiple interfaces to an ITD service.

Use a comma (",") to separate multiple interfaces. Use a hyphen ("-") to separate a range of interfaces.

Configure the required VRF and interface modes prior to associating the interface to the service.

Step 5

[no] load-balance {method {src {ip | ip-l4port [tcp | udp] range x y} | dst {ip | ip-l4port [tcp | udp] range x y}} | buckets bucket-number | mask-position mask-position | }

Example:

switch(config-itd)# load-balance method src ip buckets 16

Configures the load-balancing options for the ITD service.

The options are as follows:

method —Specifies the source or destination IP-address-based load or traffic distribution.

buckets —Specifies the number of buckets to create. One or more buckets are mapped to a node. Buckets must be configured in powers of two. The range is from 2 to 256.

Note

If you configure more buckets than the number of nodes, the buckets are applied in a round-robin fashion across all the nodes.

mask-position —Specifies the load-balance mask position number.
For services with include-acl, use least-bit (with or without mask position) to distribute fewer consecutive IP hosts to the same bucket.

Step 6

[no] virtual [ ip | ipv6 ] { ipv4-address ipv4-network-mask | ipv6-address ipv6-network-mask }[ { proto {port_num | port_any}}] [ {advertise} {enable | disable}] [device-group dgrp_name]

Example:

switch(config-itd)# virtual ip 100.100.100.100 255.255.255.255 udp 443 advertise enable active

Example:

switch(config-itd)# virtual ipv6 100::100 128 udp 443

Configures the virtual IPv4 or IPv6 address of the ITD service.

The proto options (TCP or UDP) specify that the virtual IP address will accept flows from the specified protocol. The port range is from 0 to 65535.

The [advertise {enable | disable}] option specifies whether the virtual IP route is advertised to neighboring devices. When the VIP advertise option is enabled, ITD will advertise the route to the Virtual IP address as long as one or more primary or hot-standby nodes are active in the device-group associated with the virtual IP or the default device-group under the service, as applicable. In order to enable the VIP advertise option, every primary and hot-standby node should be trackable via probes at the device-group or node level.

Note

The advertise {enable | disable} [active] option will issue a warning to use [advertise {enable | disable}] option.

Note

The advertise enable and the advertise enable active options are supported.

Multiple instances of Virtual IP can be configured under a service with the same IP address , but different netmasks( or prefix length), protocols or ports. The user will need to ensure that the matches on the virtual IP, mask protocol and port are unique, so that traffic flows can load balance as intended.

Step 7

Enter one of the following commands to determine how traffic is reassigned after a node failure:

[no] failaction node reassign
[no] failaction node least-bucket
[no] failaction bucket distribute
[no] failaction node per-bucket

Example:

switch(config-itd)# failaction node reassign

Example:

switch(config-itd)# failaction node least-bucket

Example:

switch(config-itd)# failaction bucket distribute

Example:

switch (config-itd)# failaction node per-bucket

Configures the fail-action mechanism to be used by the service.

Note

This algorithm is intended for relatively even traffic distribution but doesn't guarantee even distribution.

Step 8

[no] vrf vrf-name

Example:

switch(config-itd)# vrf RED

Specifies the VRF for the ITD service.

Step 9

[no] exclude access-list acl-name

Example:

switch(config-itd)# exclude access-list acl1

Specifies the traffic that you want ITD to exclude from the ITD load balancer.

Step 10

no shutdown

Example:

switch(config-itd)# no shutdown

Enables the ITD service.

Step 11

(Optional) show itd [itd-name]

Example:

switch(config-itd)# show itd

(Optional)

Displays the status and configuration for specified ITD instances.

Step 12

(Optional) copy running-config startup-config

Example:

switch(config-itd)# copy running-config startup-config

(Optional)

Copies the running configuration to the startup configuration.

Assigning an ACL to an ITD Service

You can use the include access control list (ACL) feature to assign an ACL to an ITD service. For each access control entry (ACE) with the permit method in the ACL, this feature filters the unwanted traffic and generates IP access lists and a route map to load-balance the permitted traffic. Load balancing is supported using either the source or destination IP address.

Before you begin

Ensure that the ITD feature is enabled.

Ensure that the device group to be added to the ITD service has been configured.

Ensure that the ACL to be assigned to the ITD service has been configured.

SUMMARY STEPS

configure terminal
[no] itd itd-name
[no] device-group device-group-name
[no] ingress interface interface
[no] load-balance {method {src {ip | ip-l4port [tcp | udp] range x y} | dst {ip | ip-l4port [tcp | udp] range x y}} | buckets bucket-number}
[no] failaction node-per-bucket
access-list acl-name

[no] shutdown
(Optional) copy running-config startup-config

DETAILED STEPS

Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters global configuration mode.

Step 2

[no] itd itd-name

Example:

switch(config)# itd service1
switch(config-itd)#

Configures an ITD service and enters ITD configuration mode. You can enter up to 32 alphanumeric characters.

Step 3

[no] device-group device-group-name

Example:

switch(config-itd)# device-group dg1

Adds an existing device group to the ITD service. The device-group-name specifies the name of the device group. You can enter up to 32 alphanumeric characters.

Step 4

[no] ingress interface interface

Example:

switch(config-itd)# ingress interface ethernet 4/1-10

Adds an ingress interface or multiple interfaces to an ITD service.

Use a comma (",") to separate multiple interfaces. Use a hyphen ("-") to separate a range of interfaces.

Step 5

[no] load-balance {method {src {ip | ip-l4port [tcp | udp] range x y} | dst {ip | ip-l4port [tcp | udp] range x y}} | buckets bucket-number}

Example:

switch(config-itd)# load-balance method src ip buckets 16

Configures the load-balancing options for the ITD service.

The options are as follows:

method —Specifies the source or destination IP-address-based load or traffic distribution.

buckets —Specifies the number of buckets to create. One or more buckets are mapped to a node. Buckets must be configured in powers of two. The range is from 2 to 256.

Note

If you configure more buckets than the number of nodes, the buckets are applied in a round-robin fashion across all the nodes.

Step 6

[no] failaction node-per-bucket

Example:

switch(config-itd)# failaction node-per-bucket

When a node failure happens the buckets assigned to this node will be distributed across the remaining active nodes. If weights are assigned to nodes, the distribution will be based on weights of the nodes.

Step 7

access-list acl-name

Example:

switch(config-itd)# access-list itd_d

Assigns an ACL to the ITD service.

Step 8

[no] shutdown

Example:

switch(config-itd)# no shutdown

Enables the ITD service.

Step 9

(Optional) copy running-config startup-config

Example:

switch(config-itd)# copy running-config startup-config

(Optional)

Copies the running configuration to the startup configuration.

Nondisruptively Adding or Deleting Nodes

You can configure an ITD session that enables you to add or delete nodes in a device group without shutting down the ITD service. Doing so minimizes traffic disruption, which can occur when you shut down the ITD service.

Before you begin

Ensure that the ITD feature is enabled.

Ensure that the device group and the ITD service have been configured.

SUMMARY STEPS

configure terminal
itd session device-group device-group-name
[no] node ip {ipv4-address | ipv6-address}
{commit | abort}
(Optional) show itd session device-group [name]
(Optional) copy running-config startup-config

DETAILED STEPS

	Command or Action	Purpose
Step 1	configure terminal Example: `switch# configure terminal switch(config)#`	Enters global configuration mode.
Step 2	itd session device-group `device-group-name` Example: `switch(config)# itd session device-group dg1 switch(config-session-device-group)#`	Creates an ITD session for the specified device group.
Step 3	[no] node ip {`ipv4-address` \| `ipv6-address`} Example: `switch(config-session-device-group)# node ip 2.2.2.1`	Adds the specified node to the ITD device group. The no form of this command deletes the specified node from the ITD device group. Repeat this step for each node that you want to add or delete.
Step 4	{commit \| abort} Example: `switch(config-session-device-group)# commit switch(config)#`	The commit command updates the ITD device group with the new or modified set of nodes, reassigns buckets, and cleans up the ITD session configuration. The abort command ignores the ITD session configuration and does not update the ITD device group.
Step 5	(Optional) show itd session device-group [`name`] Example: `switch(config)# show itd session device-group dg1`	(Optional) Displays all of the configured ITD sessions or the ITD session for the specified device group.
Step 6	(Optional) copy running-config startup-config Example: `switch(config)# copy running-config startup-config`	(Optional) Copies the running configuration to the startup configuration.

Nondisruptively Adding or Deleting ACEs in Include ACLs

You can add or delete the access control entries (ACEs) in the include ACL without shutting down the ITD service. Doing so minimizes traffic disruption, which can occur when you shut down the ITD service.

Before you begin

Ensure that the ITD feature is enabled.

Ensure that the device group and the ITD service have been configured.

Ensure that an ACL has been assigned to the ITD service.

SUMMARY STEPS

configure terminal
itd session access-list acl-name refresh
(Optional) copy running-config startup-config

DETAILED STEPS

Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters global configuration mode.

Step 2

itd session access-list acl-name refresh

Example:

switch(config)# itd session access-list test1 refresh

Internally reads the include ACL and programs the TCAM. ITD checks the old and new ACL ACEs and updates the ITD-generated ACLs.

Note

This command is required only for include ACLs.

Step 3

(Optional) copy running-config startup-config

Example:

switch(config)# copy running-config startup-config

(Optional)

Copies the running configuration to the startup configuration.

Verifying the ITD Layer-3 Configuration

To display the ITD layer-3 configuration, perform one of the following tasks:


Command	Purpose
show itd [`itd-name`] [brief \| vrf [`vrf-name`]]	Displays the status and configuration for specified ITD instances. Use the `itd-name` argument to display the status and configuration for a specific ITD instance. Use the brief keyword to display summary status and configuration information. Use the vrf keyword to display the VRFs for the specified ITD instance.
show itd session device-group [`name`]	Displays all of the configured ITD sessions or the ITD session for the specified device group.
show running-config services	Displays the configured ITD device group and services.

These examples show how to verify the ITD configuration:

switch# show itd

Name           Probe LB Scheme  Status   Buckets
-------------- ----- ---------- -------- -------
WEB            ICMP  src-ip     ACTIVE   2

Device Group                                         VRF-Name
-------------------------------------------------- -------------
WEB-SERVERS


Pool                           Interface    Status Track_id
------------------------------ ------------ ------ ---------
WEB_itd_pool                   Po-1         UP       -

Virtual IP     Netmask/Prefix            Protocol   Port
---------------------------------------- ---------- -----
10.10.10.100 / 255.255.255.255           IP           0

  Node  IP                  Config-State Weight Status     Track_id  
  ------------------------- ------------ ------ ---------- ---------
  1     10.10.10.11         Active       1      OK           -  

        Bucket List
        -----------------------------------------------------------------------
        WEB_itd_vip_1_bucket_1


  Node  IP                  Config-State Weight Status     Track_id 
  ------------------------- ------------ ------ ---------- ---------
  2     10.10.10.12         Active       1      OK           -      

        Bucket List
        -----------------------------------------------------------------------
        WEB_itd_vip_1_bucket_2

Configuration Examples for ITD

This example shows how to configure ITD and other pre-requisite features, and configure ITD device groups.

switch-1# conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch-1(config)# feature itd
switch-1(config)# feature sla sender
switch-1(config)# feature pbr
switch-1(config)# 
switch-1(config)#  itd device-group DG1
switch-1(config-device-group)#    probe icmp frequency 2 retry-down-count 2 retry-up-count 1 timeout 1
switch-1(config-device-group)#    node ip 10.200.1.2
switch-1(config-dg-node)#   node ip 10.200.2.2
switch-1(config-dg-node)# 
switch-1(config-dg-node)# 
switch-1(config-dg-node)# itd device-group DG2
switch-1(config-device-group)#    probe icmp
switch-1(config-device-group)#    node ipv6 2007::2
switch-1(config-dg-node)#   node ipv6 2008::2
switch-1(config-dg-node)# 
switch-1(config-dg-node)# end
switch-1#

This example shows how to create an ITD service with failaction as node per-bucket and the destination-based load balance method with static bucket count and associate the device groups to the service.

switch-1# conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch-1(config)# itd SER1
switch-1(config-itd)#    device-group DG1
switch-1(config-itd)#    ingress interface Ethernet1/17
switch-1(config-itd)#    failaction node per-bucket
switch-1(config-itd)#    load-balance method dst ip buckets 4
switch-1(config-itd)# no sh
Note: Configure buckets equal to or more than the total number of nodes.
 The mask position that exceeds the available bits based on the number of buckets and load-balance mode will internally default to 0.

switch-1(config-itd)# 
switch-1(config-itd)# itd SER2
switch-1(config-itd)#    device-group DG2
switch-1(config-itd)#    ingress interface Ethernet1/18
switch-1(config-itd)#    failaction node per-bucket
switch-1(config-itd)#    load-balance method dst ip buckets 4
switch-1(config-itd)# no sh
Note: Configure buckets equal to or more than the total number of nodes.
 The mask position that exceeds the available bits based on the number of buckets and load-balance mode will internally default to 0.

switch-1(config-itd)# end
switch-1#
switch-1# sh run services
!Command: show running-config services
!No configuration change since last restart
!Time: Tue Jan  5 21:05:40 2021

version 10.1(1) Bios:version 01.14 
feature itd

itd device-group DG1
  probe icmp frequency 2 timeout 1 retry-down-count 2 retry-up-count 1
  node ip 10.200.1.2 
  node ip 10.200.2.2 


itd device-group DG2
  probe icmp
  node ipv6 2007::2
  node ipv6 2008::2

itd SER1
  device-group DG1
  ingress interface Eth1/17 
  failaction node per-bucket 
  load-balance method dst ip buckets 4
  no shut

itd SER2
  device-group DG2
  ingress interface Eth1/18 
  failaction node per-bucket 
  load-balance method dst ip buckets 4
  no shut
switch-1#
switch-1# show itd brief

Legend:
 C-S(Config-State): A-Active,S-Standby,F-Failed
 ST(Status): ST-Standby,LF-Link Failed,PF-Probe Failed,PD-Peer Down,IA-Inactive

Name           LB Scheme  Status   Buckets    Interface
-------------- ---------- -------- ---------  -------------- 
SER1           dst-ip     ACTIVE   4          Eth1/17   

Source Interface
----------------
                

Device Group                                       Probe  Port
-------------------------------------------------- ----- ------
DG1                                                 ICMP       


Node  IP                  Cluster-id C-S WGT Probe Port     Probe-IP   STS
------------------------- ---------- -- --- ---- ----- --------------- --
1              10.200.1.2             A   1 ICMP                       OK
2              10.200.2.2             A   1 ICMP                       OK

Legend:
 C-S(Config-State): A-Active,S-Standby,F-Failed
 ST(Status): ST-Standby,LF-Link Failed,PF-Probe Failed,PD-Peer Down,IA-Inactive

Name           LB Scheme  Status   Buckets    Interface
-------------- ---------- -------- ---------  -------------- 
SER2           dst-ip     ACTIVE   4          Eth1/18   

Source Interface
----------------
                

Device Group                                       Probe  Port
-------------------------------------------------- ----- ------
DG2                                                 ICMP       


Node      IP                                Cluster-id C-S WGT Probe Port    Probe-IP    STS
------------------------------------------- ---------- --- --- ---- ----- --------------- --
1                                   2007::2             A   1 ICMP                       OK
2                                   2008::2             A   1 ICMP                       OK


switch-1#
switch-1# sh itd

Legend:
 ST(Status): ST-Standby,LF-Link Failed,PF-Probe Failed,PD-Peer Down,IA-Inactive

Name           LB Scheme  Status   Buckets
-------------- ---------- -------- -------
SER1           dst-ip     ACTIVE   4      

Source Interface
----------------
                

Device Group                                       Probe  Port
-------------------------------------------------- ----- ------
DG1                                                 ICMP       

Pool                           Interface    Status Track_id 
------------------------------ ------------ ------ ---------
SER1_itd_pool                  Eth1/17      UP       1      


  Node  IP                  Cluster-id Cfg-S   WGT Probe Port     Probe-IP   STS Trk# Sla_id 
  ------------------------- ---------- ------- --- ---- ----- --------------- -- --- -------
  1              10.200.1.2             Active   1 ICMP                       OK   2   10002

      Bucket List
      --------------------------------------------------------------------------
      SER1_itd_bucket_1, 3

  Node  IP                  Cluster-id Cfg-S   WGT Probe Port     Probe-IP   STS Trk# Sla_id 
  ------------------------- ---------- ------- --- ---- ----- --------------- -- --- -------
  2              10.200.2.2             Active   1 ICMP                       OK   3   10003

      Bucket List
      --------------------------------------------------------------------------
      SER1_itd_bucket_2, 4
Legend:
 ST(Status): ST-Standby,LF-Link Failed,PF-Probe Failed,PD-Peer Down,IA-Inactive

Name           LB Scheme  Status   Buckets
-------------- ---------- -------- -------
SER2           dst-ip     ACTIVE   4      

Source Interface
----------------
                

Device Group                                       Probe  Port
-------------------------------------------------- ----- ------
DG2                                                 ICMP       

Pool                           Interface    Status Track_id 
------------------------------ ------------ ------ ---------
SER2_itd_pool                  Eth1/18      UP       4      


  Node  IP                                    Cluster-id Cfg-S  WGT
  ------------------------------------------- ---------- ------- ---
  1                                   2007::2             Active   1

      Probe Port    Probe-IP    STS Trk# Sla_id
      ---- ----- --------------- -- --- -------
      ICMP                       OK   5   10004

      Bucket List
      --------------------------------------------------------------------------
      SER2_itd_bucket_1, 3

  Node  IP                                    Cluster-id Cfg-S  WGT
  ------------------------------------------- ---------- ------- ---
  2                                   2008::2             Active   1

      Probe Port    Probe-IP    STS Trk# Sla_id
      ---- ----- --------------- -- --- -------
      ICMP                       OK   6   10005

      Bucket List
      --------------------------------------------------------------------------
      SER2_itd_bucket_2, 4

switch-1#
	
switch-1# sh run rpm

!Command: show running-config rpm
!No configuration change since last restart
!Time: Tue Jan  5 21:08:12 2021

version 10.1(1) Bios:version 01.14 
feature pbr

route-map SER1_itd_pool permit 10
  match ip address SER1_itd_bucket_1 
  set ip next-hop verify-availability 10.200.1.2 track 2 force-order
route-map SER1_itd_pool permit 11
  match ip address SER1_itd_bucket_2 
  set ip next-hop verify-availability 10.200.2.2 track 3 force-order
route-map SER1_itd_pool permit 12
  match ip address SER1_itd_bucket_3 
  set ip next-hop verify-availability 10.200.1.2 track 2 force-order
route-map SER1_itd_pool permit 13
  match ip address SER1_itd_bucket_4 
  set ip next-hop verify-availability 10.200.2.2 track 3 force-order
route-map SER2_itd_pool permit 10
  match ipv6 address SER2_itd_bucket_1 
  set ipv6 next-hop verify-availability 2007::2 track 5 force-order
route-map SER2_itd_pool permit 11
  match ipv6 address SER2_itd_bucket_2 
  set ipv6 next-hop verify-availability 2008::2 track 6 force-order
route-map SER2_itd_pool permit 12
  match ipv6 address SER2_itd_bucket_3 
  set ipv6 next-hop verify-availability 2007::2 track 5 force-order
route-map SER2_itd_pool permit 13
  match ipv6 address SER2_itd_bucket_4 
  set ipv6 next-hop verify-availability 2008::2 track 6 force-order


interface Ethernet1/17
  ip policy route-map SER1_itd_pool

interface Ethernet1/18
  ipv6 policy route-map SER2_itd_pool

switch-1#
switch-1# show ip access-lists dynamic 

IP access list SER1_itd_bucket_1
        10 permit ip any 1.1.1.0 255.255.255.63 
IP access list SER1_itd_bucket_2
        10 permit ip any 1.1.1.64 255.255.255.63 
IP access list SER1_itd_bucket_3
        10 permit ip any 1.1.1.128 255.255.255.63 
IP access list SER1_itd_bucket_4
        10 permit ip any 1.1.1.192 255.255.255.63 
switch-1#
switch-1# show run track

!Command: show running-config track
!No configuration change since last restart
!Time: Tue Jan  5 21:09:25 2021

version 10.1(1) Bios:version 01.14 
track 1 interface Ethernet1/17 line-protocol
track 2 ip sla 10002 reachability
 delay up 2 down 4

track 3 ip sla 10003 reachability
 delay up 2 down 4

track 4 interface Ethernet1/18 line-protocol
track 5 ip sla 10004 reachability
 delay up 30 down 30

track 6 ip sla 10005 reachability
 delay up 30 down 30

switch-1#
switch-1# sh track
Track 1
  Interface Ethernet1/17 Line Protocol
  Line Protocol is UP
  1 changes, last change 00:05:54
  Tracked by:
    ISCM Configuration

Track 2
  IP SLA 10002 Reachability
  Reachability is UP
  2 changes, last change 00:05:50
  Latest operation return code: OK
  Latest RTT (millisecs): 1
  Tracked by:
    ISCM Configuration
    Route Map Configuration
  Delay up 2 secs, down 4 secs

Track 3
  IP SLA 10003 Reachability
  Reachability is UP
  2 changes, last change 00:05:50
  Latest operation return code: OK
  Latest RTT (millisecs): 1
  Tracked by:
    ISCM Configuration
    Route Map Configuration
  Delay up 2 secs, down 4 secs

Track 4
  Interface Ethernet1/18 Line Protocol
  Line Protocol is UP
  1 changes, last change 00:05:32
  Tracked by:
    ISCM Configuration

Track 5
  IP SLA 10004 Reachability
  Reachability is UP
  2 changes, last change 00:04:51
  Latest operation return code: OK
  Latest RTT (millisecs): 1
  Tracked by:
    ISCM Configuration
    Route Map Configuration
  Delay up 30 secs, down 30 secs
Track 6
  IP SLA 10005 Reachability
  Reachability is UP
  2 changes, last change 00:04:51
  Latest operation return code: OK
  Latest RTT (millisecs): 1
  Tracked by:
    ISCM Configuration
    Route Map Configuration
  Delay up 30 secs, down 30 secs
switch-1#
switch-1# show ip sla stat

IPSLAs Latest Operation Statistics

IPSLA operation id: 10002
        Latest RTT: 1 milliseconds
Latest operation start time: 21:11:12.861 UTC Tue Jan 05 2021
Latest operation return code: OK
Number of successes: 210
Number of failures: 1
Operation time to live: forever

IPSLA operation id: 10003
        Latest RTT: 1 milliseconds
Latest operation start time: 21:11:12.901 UTC Tue Jan 05 2021
Latest operation return code: OK
Number of successes: 210
Number of failures: 1
Operation time to live: forever

IPSLA operation id: 10004
        Latest RTT: 2 milliseconds
Latest operation start time: 21:11:04.995 UTC Tue Jan 05 2021
Latest operation return code: OK
Number of successes: 39
Number of failures: 1
Operation time to live: forever

IPSLA operation id: 10005
        Latest RTT: 1 milliseconds
Latest operation start time: 21:11:05.034 UTC Tue Jan 05 2021
Latest operation return code: OK
Number of successes: 39
Number of failures: 1
Operation time to live: forever
switch-1#

This example shows how to configure an ITD service with failaction as node reassign and fail action as node least-bucket with source-ip based load balance method.

switch-1(config)# feature itd
switch-1(config)# 
switch-1(config)# 
switch-1(config)# itd device-group DG1
switch-1(config-device-group)#   probe icmp frequency 2 timeout 1 retry-down-count 2 retry-up-count 1
switch-1(config-device-group)#   node ip 10.200.1.2 
switch-1(config-dg-node)#   node ip 10.200.2.2 
switch-1(config-dg-node)# 
switch-1(config-dg-node)# 
switch-1(config-dg-node)# itd device-group DG2
switch-1(config-device-group)#   probe icmp
switch-1(config-device-group)#   node ipv6 2007::2
switch-1(config-dg-node)#   node ipv6 2008::2
switch-1(config-dg-node)# 
switch-1(config-dg-node)# 
switch-1(config-dg-node)# itd SER1
switch-1(config-itd)#   device-group DG1
switch-1(config-itd)#   ingress interface Eth1/17 
switch-1(config-itd)#   failaction node reassign 
switch-1(config-itd)#   load-balance method src ip buckets 4
switch-1(config-itd)#   no shut
Note: Configure buckets equal to or more than the total number of nodes.
 The mask position that exceeds the available bits based on the number of buckets and load-balance mode will internally default to 0.

switch-1(config-itd)# 
switch-1(config-itd)# itd SER2
switch-1(config-itd)#   device-group DG2
switch-1(config-itd)#   ingress interface Eth1/18 
switch-1(config-itd)#   failaction node least-bucket 
switch-1(config-itd)#   load-balance method src ip
switch-1(config-itd)#   no shut
switch-1(config-itd)# end
switch-1# 
switch-1# sh run services

!Command: show running-config services
!No configuration change since last restart
!Time: Tue Jan  5 21:21:41 2021

version 10.1(1) Bios:version 01.14 
feature itd

itd device-group DG1
  probe icmp frequency 2 timeout 1 retry-down-count 2 retry-up-count 1
  node ip 10.200.1.2 
  node ip 10.200.2.2 

itd device-group DG2
  probe icmp
  node ipv6 2007::2
  node ipv6 2008::2

itd SER1
  device-group DG1
  ingress interface Eth1/17 
  failaction node reassign 
  load-balance method src ip buckets 4
  no shut

itd SER2
  device-group DG2
  ingress interface Eth1/18 
  failaction node least-bucket 
  load-balance method src ip
  no shut

switch-1#

This example shows how to add and delete ITD nodes using ITD sessions to be able to modify ITD configuration while the service is active.

switch-1(config)# itd session device-group DG1
switch-1(config-session-device-group)#                    no node ip 10.200.1.2
switch-1(config-session-device-group)#                    node ip 10.200.3.2
switch-1(config-session-dg-node)#                    node ip 10.200.4.2
switch-1(config-session-dg-node)#                    commit
switch-1(config)#                itd session device-group DG2
switch-1(config-session-device-group)#                    no node ipv6 2007::2
switch-1(config-session-device-group)#                    node ipv6 2009::2
switch-1(config-session-dg-node)#                    commit
switch-1(config)#  end
switch-1#
switch-1# sh run services

!Command: show running-config services
!No configuration change since last restart
!Time: Tue Jan  5 22:49:07 2021

version 10.1(1) Bios:version 01.14 
feature itd

itd device-group DG1
  probe icmp frequency 2 timeout 1 retry-down-count 2 retry-up-count 1
  node ip 10.200.3.2 
  node ip 10.200.2.2 
  node ip 10.200.4.2 

itd device-group DG2
  probe icmp
  node ipv6 2009::2
  node ipv6 2008::2

itd SER1
  device-group DG1
  ingress interface Eth1/17 
  failaction node reassign 
  load-balance method src ip buckets 4
  no shut

itd SER2
  device-group DG2
  ingress interface Eth1/18 
  failaction node least-bucket 
  load-balance method src ip
  no shut

switch-1#
switch-1# sh itd brief

Legend:
 C-S(Config-State): A-Active,S-Standby,F-Failed
 ST(Status): ST-Standby,LF-Link Failed,PF-Probe Failed,PD-Peer Down,IA-Inactive

Name           LB Scheme  Status   Buckets    Interface
-------------- ---------- -------- ---------  -------------- 
SER1           src-ip     ACTIVE   4          Eth1/17   

Source Interface
----------------
                

Device Group                                       Probe  Port
-------------------------------------------------- ----- ------
DG1                                                 ICMP       


Node  IP                  Cluster-id C-S WGT Probe Port     Probe-IP   STS
------------------------- ---------- -- --- ---- ----- --------------- --
1              10.200.3.2             A   1 ICMP                       OK
2              10.200.2.2             A   1 ICMP                       OK
3              10.200.4.2             A   1 ICMP                       OK

Legend:
 C-S(Config-State): A-Active,S-Standby,F-Failed
 ST(Status): ST-Standby,LF-Link Failed,PF-Probe Failed,PD-Peer Down,IA-Inactive

Name           LB Scheme  Status   Buckets    Interface
-------------- ---------- -------- ---------  -------------- 
SER2           src-ip     ACTIVE   2          Eth1/18   

Source Interface
----------------
                

Device Group                                       Probe  Port
-------------------------------------------------- ----- ------
DG2                                                 ICMP       


Node      IP                                Cluster-id C-S WGT Probe Port    Probe-IP    STS
------------------------------------------- ---------- --- --- ---- ----- --------------- --
1                                   2009::2             A   1 ICMP                       OK
2                                   2008::2             A   1 ICMP                       OK


switch-1#

This example shows how to filter traffic for an ITD service using user-defined access-lists.

switch-1# conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch-1(config)# ip access-list acl4
switch-1(config-acl)#                  10 permit ip 7.7.1.0/24 6.6.1.0/24
switch-1(config-acl)#                  20 permit ip 7.7.2.0/26 6.6.2.0/26
switch-1(config-acl)#                ipv6 access-list acl6
switch-1(config-ipv6-acl)#                  10 permit ipv6 2004::5/120 2005::5/120
switch-1(config-ipv6-acl)#                  20 permit ipv6 2004::100/122 2005::100/122
switch-1(config-ipv6-acl)#                    
switch-1(config-ipv6-acl)# 
switch-1(config-ipv6-acl)#  itd SER1
switch-1(config-itd)#                   shut
switch-1(config-itd)#                   access-list acl4
switch-1(config-itd)#                   no shut
Note: Configure buckets equal to or more than the total number of nodes.
 The mask position that exceeds the available bits based on the number of buckets and load-balance mode will internally default to 0.

switch-1(config-itd)#                 itd SER2
switch-1(config-itd)#                   shut
switch-1(config-itd)#                   access-list ipv6 acl6
switch-1(config-itd)#                   no shut
switch-1(config-itd)# end
switch-1#
switch-1# sh run services

!Command: show running-config services
!No configuration change since last restart
!Time: Tue Jan  5 22:57:25 2021

version 10.1(1) Bios:version 01.14 
feature itd

itd device-group DG1
  probe icmp frequency 2 timeout 1 retry-down-count 2 retry-up-count 1
  node ip 10.200.3.2 
  node ip 10.200.2.2 
  node ip 10.200.4.2 

itd device-group DG2
  probe icmp
  node ipv6 2009::2
  node ipv6 2008::2

itd SER1
  device-group DG1
  ingress interface Eth1/17 
  failaction node reassign 
  load-balance method src ip buckets 4
  access-list acl4
  no shut

itd SER2
  device-group DG2
  ingress interface Eth1/18 
  failaction node least-bucket 
  load-balance method src ip
  access-list ipv6 acl6
  no shut

switch-1#

This example demonstrates how to exclude traffic from an ITD service using user-defined access-lists.

switch-1# conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch-1(config)# itd SER1
switch-1(config-itd)# shut
switch-1(config-itd)# no access-list acl4
switch-1(config-itd)# exclude access-list acl4
switch-1(config-itd)# no sh
Note: Configure buckets equal to or more than the total number of nodes.
 The mask position that exceeds the available bits based on the number of buckets and load-balance mode will internally default to 0.

switch-1(config-itd)# itd SER2
switch-1(config-itd)# sh
switch-1(config-itd)# no access-list ipv6 acl6
switch-1(config-itd)# exclude access-list acl6
switch-1(config-itd)# no sh
switch-1(config-itd)# end
switch-1#
switch-1# sh run services

!Command: show running-config services
!No configuration change since last restart
!Time: Tue Jan  5 23:01:38 2021

version 10.1(1) Bios:version 01.14 
feature itd

itd device-group DG1
  probe icmp frequency 2 timeout 1 retry-down-count 2 retry-up-count 1
  node ip 10.200.3.2 
  node ip 10.200.2.2 
  node ip 10.200.4.2 

itd device-group DG2
  probe icmp
  node ipv6 2009::2
  node ipv6 2008::2

itd SER1
  device-group DG1
  ingress interface Eth1/17 
  failaction node reassign 
  load-balance method src ip buckets 4
  exclude access-list acl4
  no shut

itd SER2
  device-group DG2
  ingress interface Eth1/18 
  failaction node least-bucket 
  load-balance method src ip
  exclude access-list acl6
  no shut

switch-1#

This example shows how to update the rules for a user-defined access-list and enable the changes for ITD services using such user ACLS.

switch-1# conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch-1(config)# ip access-list acl5 
switch-1(config-acl)#                    10 permit ip 7.7.1.0/24 6.6.1.0/24
switch-1(config-acl)#                itd SER1
switch-1(config-itd)#                    shut
switch-1(config-itd)#                    access-list acl5
switch-1(config-itd)#                    no shut
Note: Configure buckets equal to or more than the total number of nodes.
 The mask position that exceeds the available bits based on the number of buckets and load-balance mode will internally default to 0.

switch-1(config-itd)#  ip access-list acl5 
switch-1(config-acl)#                   20 permit ip 7.7.2.0/26 6.6.2.0/26
switch-1(config-acl)#                itd session access-list acl5 refresh 
switch-1(config)#  end
switch-1#
switch-1# sh run services

!Command: show running-config services
!No configuration change since last restart
!Time: Tue Jan  5 23:07:42 2021

version 10.1(1) Bios:version 01.14 
feature itd

itd device-group DG1
  probe icmp frequency 2 timeout 1 retry-down-count 2 retry-up-count 1
  node ip 10.200.3.2 
  node ip 10.200.2.2 
  node ip 10.200.4.2 

itd device-group DG2
  probe icmp
  node ipv6 2009::2
  node ipv6 2008::2

itd SER1
  device-group DG1
  ingress interface Eth1/17 
  failaction node reassign 
  load-balance method src ip buckets 4
  access-list acl5
  exclude access-list acl4
  no shut

itd SER2
  device-group DG2
  ingress interface Eth1/18 
  failaction node least-bucket 
  load-balance method src ip
  exclude access-list acl6
  no shut

switch-1#

This example shows how to use an ITD service specifically for traffic destined to defined ITD virtual IP addresses.

switch-1# conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch-1(config)# itd SER1
switch-1(config-itd)#                            shut
switch-1(config-itd)#                            no access-list acl5
switch-1(config-itd)#                            load-balance method src ip buckets 64
switch-1(config-itd)#                            virtual ip 6.6.1.1 255.255.255.192
switch-1(config-itd)#                            virtual ip 6.6.1.64 255.255.255.192
switch-1(config-itd)#                            failaction node per-bucket
switch-1(config-itd)#                            no shut
Note: Configure buckets equal to or more than the total number of nodes.
 The mask position that exceeds the available bits based on the number of buckets and load-balance mode will internally default to 0.

switch-1(config-itd)#                          itd SER2
switch-1(config-itd)#                            shut
switch-1(config-itd)#                            load-balance method src ip buckets 64
switch-1(config-itd)#                            virtual ipv6 2005::100 121
switch-1(config-itd)#                            virtual ipv6 2005:: 121
switch-1(config-itd)#                            failaction bucket distribute
switch-1(config-itd)#                            no shut
Note: Configure buckets equal to or more than the total number of nodes.
 The mask position that exceeds the available bits based on the number of buckets and load-balance mode will internally default to 0.

switch-1(config-itd)#  end
switch-1#
switch-1# sh run services

!Command: show running-config services
!No configuration change since last restart
!Time: Tue Jan  5 23:17:20 2021

version 10.1(1) Bios:version 01.14 
feature itd

itd device-group DG1
  probe icmp frequency 2 timeout 1 retry-down-count 2 retry-up-count 1
  node ip 10.200.3.2 
  node ip 10.200.2.2 
  node ip 10.200.4.2 

itd device-group DG2
  probe icmp
  node ipv6 2009::2
  node ipv6 2008::2

itd SER1
  device-group DG1
  virtual ip 6.6.1.1 255.255.255.192
  virtual ip 6.6.1.64 255.255.255.192
  ingress interface Eth1/17 
  failaction node per-bucket 
  load-balance method src ip buckets 64
  exclude access-list acl4
  no shut

itd SER2
  device-group DG2
  virtual ipv6 2005::100 121
  virtual ipv6 2005:: 121
  ingress interface Eth1/18 
  failaction bucket distribute 
  load-balance method src ip buckets 64
  exclude access-list acl6
  no shut

switch-1#
switch-1# sh itd brief

Legend:
 C-S(Config-State): A-Active,S-Standby,F-Failed
 ST(Status): ST-Standby,LF-Link Failed,PF-Probe Failed,PD-Peer Down,IA-Inactive

Name           LB Scheme  Status   Buckets    Interface
-------------- ---------- -------- ---------  -------------- 
SER1           src-ip     ACTIVE   64         Eth1/17   

Source Interface
----------------
                

Exclude ACL
-------------------------------
 acl4                            

Device Group                                       Probe  Port
-------------------------------------------------- ----- ------
DG1                                                 ICMP       

Virtual IP                              Netmask/Prefix Protocol     Port 
------------------------------------------------------ ------------ ----------
6.6.1.1 / 255.255.255.192                              IP           0         


Node  IP                  Cluster-id C-S WGT Probe Port     Probe-IP   STS
------------------------- ---------- -- --- ---- ----- --------------- --
1              10.200.3.2             A   1 ICMP                       OK
2              10.200.2.2             A   1 ICMP                       OK
3              10.200.4.2             A   1 ICMP                       OK

Virtual IP                              Netmask/Prefix Protocol     Port 
------------------------------------------------------ ------------ ----------
6.6.1.64 / 255.255.255.192                             IP           0         


Node  IP                  Cluster-id C-S WGT Probe Port     Probe-IP   STS
------------------------- ---------- -- --- ---- ----- --------------- --
1              10.200.3.2             A   1 ICMP                       OK
2              10.200.2.2             A   1 ICMP                       OK
3              10.200.4.2             A   1 ICMP                       OK

Legend:
 C-S(Config-State): A-Active,S-Standby,F-Failed
 ST(Status): ST-Standby,LF-Link Failed,PF-Probe Failed,PD-Peer Down,IA-Inactive

Name           LB Scheme  Status   Buckets    Interface
-------------- ---------- -------- ---------  -------------- 
SER2           src-ip     ACTIVE   64         Eth1/18   

Source Interface
----------------
                

Exclude ACL
-------------------------------
 acl6                            

Device Group                                       Probe  Port
-------------------------------------------------- ----- ------
DG2                                                 ICMP       

Virtual IP                              Netmask/Prefix Protocol     Port 
------------------------------------------------------ ------------ ----------
2005::100 / 121                                        IP           0         


Node      IP                                Cluster-id C-S WGT Probe Port    Probe-IP    STS
------------------------------------------- ---------- --- --- ---- ----- --------------- --
1                                   2009::2             A   1 ICMP                       OK
2                                   2008::2             A   1 ICMP                       OK

Virtual IP                              Netmask/Prefix Protocol     Port 
------------------------------------------------------ ------------ ----------
2005:: / 121                                           IP           0         


Node      IP                                Cluster-id C-S WGT Probe Port    Probe-IP    STS
------------------------------------------- ---------- --- --- ---- ----- --------------- --
1                                   2009::2             A   1 ICMP                       OK
2                                   2008::2             A   1 ICMP                       OK

switch-1#

Configuration Example: One-Arm Deployment Mode

The configuration below uses the topology in the following figure:

Step 1: Define the device group.


switch(config)# itd device-group DG
switch(config-device-group)# node ip 210.10.10.11
switch(config-device-group)# node ip 210.10.10.12
switch(config-device-group)# node ip 210.10.10.13
switch(config-device-group)# node ip 210.10.10.14
switch(config-device-group)# probe icmp

Step 2: Define the ITD service.


switch(config)# itd HTTP
switch(config-itd)# ingress interface port-channel 1
switch(config-itd)# device-group DG
switch(config-itd)# no shutdown

Configuration Example: Server Load-Balancing Deployment Mode

The configuration below uses the topology in the following figure:

Figure 5. ITD Load Distribution with VIP

Step 1: Define the device group.


switch(config)# itd device-group DG
switch(config-device-group)# node ip 192.168.2.11
switch(config-device-group)# node ip 192.168.2.12
switch(config-device-group)# node ip 192.168.2.13
switch(config-device-group)# node ip 192.168.2.14
switch(config-device-group)# probe icmp

Step 2: Define the ITD service.


switch(config)# itd HTTP
switch(config-itd)# ingress interface port-channel 1
switch(config-itd)# ingress interface port-channel 2
switch(config-itd)# ingress interface port-channel 3
switch(config-itd)# device-group DG
Switch(config-itd)# virtual ip 172.16.1.1 255.255.255.255
switch(config-itd)# no shutdown

Configuration Example: ITD as WCCP Replacement (Web-Proxy Deployment Mode)

A proxy server acts as an intermediary for requests from clients seeking resources from other servers. A web-proxy server specifically operates as an intermediary between a local network and the Internet. Typically, a web-proxy server needs the network device to redirect Internet-bound web traffic toward it (forward flow); however, subsequent packet forwarding only requires the network device to forward the packet regularly.

In a web-proxy deployment with ITD, the switch matches the Internet-bound web traffic and load balances it toward the proxy servers. The proxy servers work in an autonomous mode (independent of WCCP and as Active-Active) and handle the traffic that gets redirected to them. The node health probing done through ITD serves the purpose of tracking the state of the nodes and removing or adding them back appropriately based on their availability. Standby servers can also be configured at the group level or node level for redundancy.

ITD redirection is normally only required in the forward direction in the client-facing VLAN. Subsequently, the packets are routed or forwarded without any ITD redirection or distribution. ITD with such web-proxy deployments only need one ITD service, which is configured for the forward direction. However, reverse traffic redirection is required, with traffic selection based on the source Layer 4 ports. Flow symmetry also needs to be maintained by reversing the LB parameter.

With ITD for web-proxy deployments, ITD probes are used to check the availability of the web-proxy server, which is critical because traffic sent toward a failed proxy server is lost.

The configuration below uses the topology in the following figure:

In this example, destination port 80/443 (ingress VLAN 10) to the Internet will be distributed to web-proxy servers 10.1.50.1 and 10.1.50.2. Traffic on VLAN 10 destined to private networks (10.0.0.0/8, 192.168.0.0/16, 172.16.0.0/12) will not be sent to the proxy.

Step 0: Configure an access-list

ip access-list ACL1
  10 permit ip any any tcp 80
  20 permit ip any any tcp 443

Step 1: Configure the ITD device group web-proxy servers and point to the server IP addresses.

itd device-group Web_Proxy_Servers
  probe icmp
  node ip 10.1.50.1
  node ip 10.1.50.2

Step 2: Configure an exclude ACL to exclude all traffic destined to private IP addresses.

ip access-list itd_exclude_ACL
  10 permit ip any 10.0.0.0/8
  20 permit ip any 192.168.0.0/16
  30 permit ip any 172.16.0.0/12

Step 3: Apply the exclude ACL.

Itd Web_proxy_SERVICE
  device-group Web_Proxy_Servers
  exclude access-list itd_exclude_ACL
  access-list ACL1
  ingress interface Vlan 10
  failaction node reassign 
  load-balance method src ip
  no shutdown

If return traffic redirection is also required for any reason, the following additional configuration steps are needed.

Note

Only port filtering is possible using the Layer 4 range operator. Also, the exclude ACL supports only permit entries.

Step 4: Configure the return exclude ACL to exclude all but ports 80 and 443.

ip access-list itd_exclude_return	
  10 permit tcp any range 0 79 any
  20 permit tcp any range 81 442 any
  30 permit tcp any range 444 65535 any

Step 5: Configure the return ITD service for the return traffic and apply the exclude ACL.

Itd Web_proxy_SERVICE		
  device-group Web_Proxy_Servers   	 
  exclude access-list itd_exclude_return
  ingress interface Vlan 20		 <- Internet-facing ingress interface on the Nexus switch
  failaction node reassign 
  load-balance method dst ip		<- Flow symmetry between forward/return flow achieved by flipping the LB parameter
  no shutdown

Configuration Example: Firewall on a Stick

ITD Services

An ITD service configuration defines the ITD traffic distribution for a particular direction of the traffic flow. If both directions of a flow need to be redirected, two ITD services need to be configured, one for the forward traffic flow and one for the return traffic flow. Because an ASA has different inside and outside interface IP addresses, two different device groups also need to be configured to point to the corresponding inside and outside IP addresses.

ASA VLANs

The ITD forward and return services are attached to the inside and outside VLAN SVIs on the Nexus switch. Because a security application such as a firewall needs to examine all traffic, no traffic filtering is configured on the services. As a result, any traffic that hits the SVI is redirected to the corresponding ASA interfaces.

If the ASA interfaces are configured on the same VLANs as that of the switch, the traffic going to the switch from the firewall is redirected to the ASA due to the presence of an ITD service on another VLAN on the switch. Therefore, a pair of separate VLANs is required to prevent traffic looping between the firewalls and the Nexus switch.

This diagram shows VLANs 10 and 20 as the inside and outside interfaces toward the source and destination on the network. VLANs 100 and 200 are used toward the ASAs to ensure loop-free traffic.

Flow Symmetry

Firewalls typically inspect traffic flows in both the forward and return directions. Due to the stateful nature of the inspection, it is generally required that flow symmetry be maintained during normal operation of firewalls that are not clustered. Even for clustered firewalls, the asymmetry of traffic flows results in the increased redirection of flows over cluster control links. The increase of asymmetric flows adds unnecessary overhead to the firewalls and adversely impedes performance.

Flow symmetry can be achieved using the inherent IP persistence and deterministic nature of the ITD algorithms. A typical ITD configuration for firewalls uses one ITD service for the forward flow and one ITD service for the return flow. Configuring these two ITD services in such a way that the value of the load-balance parameter remains the same for both services ensures that flow symmetry is maintained.

Figure 8. Flow Symmetry in ITD ASA Deployment

This diagram shows how the source IP address of the forward flow and the destination IP address of the reverse flow remain constant. Choosing the appropriate parameter for the each ITD service ensures flow symmetry due to ITD IP persistence.

Link Failures

When the ASA inside or outside interface fails, the traffic coming into the other side of that ASA can be lost because the egress interface for traffic is down. The ITD peer switch node state synchronization feature can resolve this issue by removing the remote side of the ASA from ITD and synchronizing the node states across the switches.

The ITD peer switch node state synchronization feature is supported only in a dual-switch non-vPC (or single switch) topology. ASA clustering also solves this problem because clustering ensures that the ASA is fully brought down in the case of such failures. The firewall-on-a-stick implementation (single link or vPC) does not address this issue because the ASA inside and outside interfaces belong to the same physical (or virtual) interface.

Configuration Example

In a firewall on a stick deployment, vPC port-channel (or single port) trunks are typically used to connect the ASAs to the switches. In this configuration, the inside and outside interfaces are dot1q subinterfaces (VLAN 100 and 200), and the switches have two VLANs or SVIs each in the inside and outside contexts without physical port separation between them.

Figure 10. Firewall on a Stick (with vPC) Deployment

Step 1: Configure the switch.

Note

This example shows a partial configuration of switch Sw1. The configuration needs to be extended appropriately toward all the ASAs similarly. Other features are assumed to be configured already.

interface vlan 10
		description Inside_Vlan_to_Network
		vrf member INSIDE
		ip address 192.168.10.10/24
		hsrp 10
				ip address 192.168.10.1

interface vlan 20
		description Outside_Vlan_to_Network
		vrf member OUTSIDE
		ip address 192.168.20.10/24
		hsrp 20
				ip address 192.168.20.1

interface vlan 100
		description Inside_Vlan_to_ASA
		vrf member INSIDE
		ip address 192.168.100.10/24
		hsrp 100
				ip address 192.168.100.1

interface vlan 200
		description Outside_Vlan_to_ASA
		vrf member OUTSIDE
		ip address 192.168.200.10/24
		hsrp 200
				ip address 192.168.200.1

interface port-channel 11
		description VPC_TO_ASA1
		switchport mode trunk
		switchport trunk allowed vlan 100,200
		vpc 11
		no shutdown

interface ethernet 4/25
		description Link_To_ITD-ASA-1
		switchport
		switchport mode trunk
		switchport trunk allowed vlan 100,200
		channel-group 11 mode active
		no shutdown

interface port-channel 41
		description Downstream_vPC_to_network
		switchport mode trunk
		switchport trunk allowed vlan 10,20
		vpc 41
		no shutdown

interface ethernet 5/1-4
		description Downstream_vPC_member
		switchport
		switchport mode trunk
		switchport trunk allowed vlan 10,20
		channel-group 41
		no shutdown


itd device-group FW_INSIDE
				#Config Firewall Inside interfaces as nodes
		node ip 192.168.100.111
		node ip 192.168.100.112
		node ip 192.168.100.113
		node ip 192.168.100.114
probe icmp frequency 5 timeout 5 retry-count 1

itd device-group FW_OUTSIDE
				#Config Firewall Outside interfaces as nodes
		node ip 192.168.200.111
		node ip 192.168.200.112
		node ip 192.168.200.113
		node ip 192.168.200.114
probe icmp frequency 5 timeout 5 retry-count 1

itd INSIDE
		vrf INSIDE
				#applies ITD service to VRF 'INSIDE'
		device-group FW_INSIDE
				#FW inside interfaces attached to service.
		ingress interface vlan 10
				#applies ITD route map to vlan 1101 interface
		failaction node reassign
				#To use the next available Active FW if an FW goes offline
		load-balance method src ip buckets 16
				#distributes traffic into 16 buckets
				#load balances traffic based on Source IP.
				#OUTSIDE service uses Dest IP.
		no shut

itd OUTSIDE
		vrf OUTSIDE
				#applies ITD service to VRF 'OUTSIDE'
		device-group FW_OUTSIDE
		ingress interface vlan 20
		failaction node reassign
		load-balance method dst ip buckets 16
				#load balances traffic based on Dest IP.
				#INSIDE service uses Src IP.
		no shut

Step 2: Configure ASA.

interface port-channel 11
		nameif aggregate
		security-level 100
		no ip address

interface port-channel 11.100
		description INSIDE
		vlan 100
		nameif inside
		security-level 100
		ip address 192.168.100.111 255.255.255.0

interface port-channel 11.200
		description OUTSIDE
		vlan 200
		nameif outside
		security-level 100
		ip address 192.168.200.111 255.255.255.0

same-security-traffic permit inter-interface

interface TenGigabitEthernet 0/6
		description CONNECTED_TO_SWITCH-A-VPC
		channel-group 11 mode active
		no nameif
		no security-level

interface TenGigabitEthernet 0/7
		description CONNECTED_TO_SWITCH-B-VPC
		channel-group 11 mode active
		no nameif
		no security-level

The following points apply to this example topology:

VLANs 10, 20, 100, and 200 and their SVIs are mapped to appropriate VRFs.
This example uses an ITD load-balancing configuration to achieve flow symmetry.
In a vPC scenario, as long as one member of the vPC is up, there is no change to ITD. The ITD redirection on the switch with a failed vPC leg will traverse the peer switch through the peer link as in a typical vPC deployment.
In this topology, traffic is not lost upon physical link failure because the inside and outside interfaces are tied to the same physical or virtual interface on the ASA (dot1q subinterfaces).
To support routing protocol neighbors over a vPC, the layer3 peer-router command needs to be configured within the vPC domain.
VRFs are needed because Layer 3 interfaces are used to connect to both inside and outside firewall interfaces. VRFs are put in place to prevent traffic from being (inter-VLAN) routed around the firewall in certain cases.
Traffic is directed toward ASAs using policy-based routing, so routes are not needed.

Configuration Example: Firewall in Dual-Switch Sandwich Mode with vPCs

For sandwich mode with vPCs, the inside and outside ASA interfaces are each assigned to separate port-channel bundles. As a result of the vPCs, a single link failure does not impede the traffic flow, and ITD will continue to forward through the peer switch's link toward the ASA.

Figure 11. Dual-Switch Sandwich Mode with vPCs

Step 1: Configure the two switches.

switch #1:
interface vlan 10
		description INSIDE_VLAN
		ip address 192.168.10.10/24

interface vlan 100
		description FW_INSIDE_VLAN
		ip address 192.168.100.10/24

interface port-channel 11
		description To_ASA-1_INSIDE
		switchport mode access
		switchport access vlan 100
		vpc 11

interface ethernet 4/1
		description To_ASA-1_INSIDE
		switchport mode access
		switchport access vlan 100
		channel-group 11 mode active


switch #2:
interface vlan 20
		description OUTSIDE_VLAN
		ip address 192.168.20.10/24

interface vlan 200
		description FW_OUTSIDE_VLAN
		ip address 192.168.200.10/24

interface port-channel 21
		description To_ASA-1_OUTSIDE
		switchport mode access
		switchport access vlan 200
		vpc 11

interface ethernet 4/25
		description To_ASA-1_OUTSIDE
		switchport mode access
		switchport access vlan 200
		channel-group 21 mode active

Step 2: Configure ASA.

interface port-channel 11
		description INSIDE
		vlan 100
		nameif inside
		security-level 100
		ip address 192.168.100.111 255.255.255.0

interface port-channel 21
		description OUTSIDE
		vlan 100
		nameif outside
		security-level 100
		ip address 192.168.200.111 255.255.255.0

same-security-traffic permit inter-interface

interface TenGigabitEthernet 0/6
		description CONNECTED_TO_SWITCH-A-VPC
		channel-group 11 mode active
		no nameif
		no security-level

interface TenGigabitEthernet 0/7
		description CONNECTED_TO_SWITCH-B-VPC
		channel-group 11 mode active
		no nameif
		no security-level

interface TenGigabitEthernet 0/8
		description CONNECTED_TO_SWITCH-A-VPC
		channel-group 21 mode active
		no nameif
		no security-level

interface TenGigabitEthernet 0/9
		description CONNECTED_TO_SWITCH-B-VPC
		channel-group 21 mode active
		no nameif
		no security-level

The following points apply to this example topology:

This example uses an ITD load-balancing configuration to achieve flow symmetry.
In a vPC scenario, as long as one member of the vPC is up, there is no change to ITD. The ITD redirection on the switch with a failed vPC leg will traverse the peer switch through the peer link as in a typical vPC deployment.
In this topology, traffic loss can occur if one of the port channels on the ASA (or a single physical link in a non-vPC topology) fails.
To support routing protocol neighbors over a vPC, the layer3 peer-router command needs to be configured within the vPC domain.
Traffic is directed toward ASAs using policy-based routing, so routes are not needed.

Configuration Example: Firewall in Layer 3 Clustering

An ASA cluster consists of multiple ASAs acting as a single unit. Grouping multiple ASAs together as a single logical device provides the convenience of a single device (management and integration into a network) while achieving increased throughput and redundancy of multiple devices.

ITD can load balance to individual mode Layer 3 ASA clusters. ITD is complementary to clustering in that ITD provides the predictability of knowing which flows are handled by each firewall. Instead of relying on OSPF ECMP and port-channel hashing algorithms, you can use ITD buckets to determine these flows.

With Layer 3 clusters, the flow owner can be predetermined based on the bucket allocation. Without ITD and Layer 3 clustering, the initial choice of owner is typically unpredictable. With ITD, the owner can be predetermined.

ASA clustering also uses a backup flow owner. For every flow traversing any particular firewall in the cluster, another firewall stores the state of that flow and the ASA that owns the flow. If the real active flow owner fails, ITD failaction reassign will cause all flows (the bucket) from the failed owner ASA to shift to the next active node listed in the device group. If the new firewall to receive this traffic is not the backup owner for the flows it receives, it should receive the flow state information from the backup owner and process the traffic seamlessly.

A potential drawback to using ASA clustering with ITD is that backup flows and other cluster table operations consume memory and CPU resources that non-clustered firewalls do not. Therefore, firewall performance might improve when using non-clustered firewalls.

The following table shows a summary comparison of the impact to the cluster control link (CCL) that occurs with ECMP versus ITD when the ASA device status changes.

Table 3. ECMP versus ITD - CCL Impact Summary Comparison
ASA Status	ITD	ECMP
Steady State	Minimal traffic on the CCL and expected traffic types. Exact same load distribution irrespective of the type of line card and switch.	Minimal traffic on the CCL if the same line card type and switch model is used everywhere. If differing hardware is used, a higher level of asymmetry might occur, causing traffic on the CCL network. Each hardware has a different hash function. Two switches (for example, in a vPC) might send the same flow to different ASA devices, causing CCL traffic.
Single ASA Failure	No additional traffic on the CCL. ITD offers IP stickiness and resilient hashing.	All flows are rehashed, and additional traffic redirection occurs on the CCL. Traffic to all ASA devices in the cluster might be affected.
Single ASA Recovery	Traffic redirection can occur on the CCL between two ASA devices in the cluster: the recovered ASA that receives a bucket and the ASA that previously serviced that bucket.	Additional traffic redirection can occur on the CCL. Traffic to all ASA devices in the cluster might be affected.
ASA Addition	Minimal additional traffic on the CCL.	All flows are rehashed, and additional traffic redirection occurs on the CCL. Traffic to all ASA devices in the cluster might be affected.

Figure 12. ASA Cluster with Dual-Switch Sandwich with vPC

Step 1: Configure the two switches.

Note

The introduction of clustering does not change the ITD configuration. The ITD configuration depends on the type of topology. In this example, the configuration is the same as in the dual-switch sandwich with vPC topology.

switch #1:
interface vlan 10
		description INSIDE_VLAN
		ip address 192.168.10.10/24

interface vlan 100
		description FW_INSIDE_VLAN
		ip address 192.168.100.10/24

interface port-channel 11
		description To_ASA-1_INSIDE
		switchport mode access
		switchport access vlan 100
		vpc 11

interface ethernet 4/1
		description To_ASA-1_INSIDE
		switchport mode access
		switchport access vlan 100
		channel-group 11 mode active


switch #2:
interface vlan 20
		description OUTSIDE_VLAN
		ip address 192.168.20.10/24

interface vlan 200
		description FW_OUTSIDE_VLAN
		ip address 192.168.200.10/24

interface port-channel 21
		description To_ASA-1_OUTSIDE
		switchport mode access
		switchport access vlan 200
		vpc 11

interface ethernet 4/25
		description To_ASA-1_OUTSIDE
		switchport mode access
		switchport access vlan 200
		channel-group 21 mode active

Step 2: Configure ASA.

cluster group ASA-CLUSTER-L3
		local-unit ASA1
		cluster-interface port-channel 31
		ip address 192.168.250.100 255.255.255.0
		piority 1
		health-check holdtime 1.5
		clacp system-mac auto system-priority 1
		enable

mac-address pool MAC-INSIDE aaaa.0101.0001 - aaaa.0101.0008
mac-address pool MAC-OUTSIDE aaaa.0100.0001 - aaaa.0100.0008
ip local pool IP-OUTSIDE 192.168.200.111-192.168.200.114
ip local pool IP-INSIDE 192.168.100.111-192.168.100.114

interface port-channel 11
		description INSIDE
		lacp max-bundle 8
		mac-address cluster-pool MAC-INSIDE
		nameif inside
		security-level 100
		ip address 192.168.100.11 255.255.255.0 cluster-pool IP-INSIDE

interface port-channel 21
		description OUTSIDE
		lacp max-bundle 8
		mac-address cluster-pool MAC-OUTSIDE
		nameif outside
		security-level 100
		ip address 192.168.200.11 255.255.255.0 cluster-pool IP-OUTSIDE

interface port-channel 31
		description Clustering Interface
		lacp max-bundle 8

interface TenGigabitEthernet 0/6
		channel-group 11 mode active
		no nameif
		no security-level
		no ip address

interface TenGigabitEthernet 0/7
		channel-group 11 mode active
		no nameif
		no security-level
		no ip address

interface TenGigabitEthernet 0/8
		channel-group 21 mode active
		no nameif
		no security-level
		no ip address

interface TenGigabitEthernet 0/9
		channel-group 21 mode active
		no nameif
		no security-level
		no ip address

interface TenGigabitEthernet 1/0
		channel-group 31 mode on
		no nameif
		no security-level
		no ip address

interface TenGigabitEthernet 1/1
		channel-group 31 mode on
		no nameif
		no security-level
		no ip address

In this example, port channels 11 and 21 are used for the inside and outside interfaces. Port channel 31 is the clustering interface. Individual interfaces are normal routed interfaces, each with its own IP address taken from a pool of IP addresses. The main cluster IP address is a fixed address for the cluster that always belongs to the current primary unit. Similarly, a MAC address POOL is also configured and used under the corresponding inside or outside port channel.

Cisco Nexus 3600 Series NX-OS Intelligent Traffic Director Configuration Guide, Release 10.3(x)

Bias-Free Language

Results

Chapter: Configuring ITD

Configuring ITD

About ITD

One-Arm Deployment Mode

Server Load-Balancing Deployment Mode

Device Groups

Multiple Device Groups in an ITD Service

VRF Support

Include and Exclude ACLs

Virtual IP Address Filtering

Port Number-Based Filtering

Hot-Standby

Multiple Ingress Interfaces

System Health Monitoring

Health of an Interface Connected to a Node

Failaction Reassignment

Failaction Node Reassign

Failaction Node Least-Bucket

Failaction Bucket Distribute

Failaction Node-Per-Bucket

No Failaction Reassignment

No Failaction Reassignment with a Probe Configured

No Failaction Reassignment without a Probe Configured

Licensing Requirements

Supported Platforms

Guidelines and Limitations for ITD

ITD Support Summary

Default Settings for ITD

Configuring ITD

Enabling ITD

Before you begin

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Configuring a Device Group

Before you begin

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Configuring an ITD Service

Before you begin

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Assigning an ACL to an ITD Service

Before you begin

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Example: