Cisco Nexus 9000 Series NX-OS Command Reference (Configuration Commands), Release 10.2(x)

l2rib dup-host-mac-detection

{ no l2rib dup-host-mac-detection } | { l2rib dup-host-mac-detection <num-of-moves> <duration> }

Syntax Description


no	Negate a command or set its defaults
l2rib	Layer 2 routing information base
dup-host-mac-detection	Set Duplicate-Host-MAC-Detection parameters
num-of-moves	Number of host moves to be allowed
duration	Duplicate detection timeout in secs for host moves

Command Mode

/exec/configure

l2rib dup-host-mac-recovery

{ no l2rib dup-host-mac-recovery } | { l2rib dup-host-mac-recovery <timeout> <retry-count> }

Syntax Description


no	Negate a command or set its defaults
l2rib	Layer 2 routing information base
dup-host-mac-recovery	Set Duplicate-Host-MAC-Recovery (Unfreeze) parameters
timeout	Unfreeze timeout (secs)
retry-count	Unfreeze retry count

Command Mode

/exec/configure

label-allocation-mode per-vrf

[no] label-allocation-mode per-vrf

Syntax Description


no	(Optional) Negate a command or set its defaults
label-allocation-mode	Configure label allocation mode
per-vrf	per VRF label allocation mode

Command Mode

/exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6

label allocate global

[no] label allocate global { all-routes | host-routes | prefix-list <pfx-list> }

Syntax Description


no	(Optional) Negate a command or set its defaults
label	LDP label configuration
allocate	Allocate local labels
global	Specify default VPN Routing/Forwarding instance
all-routes	Allocate local labels for all routes
host-routes	Allocate local labels for host routes only (default)
prefix-list	Specify a prefix-list for local label filtering
pfx-list	IP prefix-list for destination prefixes

Command Mode

/exec/configure/ldp

lacp graceful-convergence

lacp graceful-convergence | no lacp graceful-convergence

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
graceful-convergence	Configure port-channel lacp graceful convergence. Disable this only with lacp ports connected to Non-Nexus peer. Disabling this with Nexus peer can lead to port suspension

Command Mode

/exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp max-bundle

lacp max-bundle <max-bundle-number> | no lacp max-bundle [ <max-bundle-number> ]

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
max-bundle	Configure the port-channel max-bundle
max-bundle-number	Enter the max-bundle number

Command Mode

/exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp min-links

lacp min-links <min-links-number> | no lacp min-links [ <min-links-number> ]

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
min-links	Configure the port-channel min-links
min-links-number	Enter the min-link number

Command Mode

/exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp mode delay

[no] lacp mode delay

Syntax Description


no	(Optional) Negate a command or set its defaults
lacp	Set LACP parameters for the interface
mode	Enter the LACP mode
delay	Configure delayed lacp on the port-channel

Command Mode

/exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp mode delay

[no] lacp mode delay

Syntax Description


no	(Optional) Negate a command or set its defaults
lacp	Set LACP parameters for the interface
mode	Enter the LACP mode
delay	Configure delayed lacp on the port-channel

Command Mode

/exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp port-number front-panel

lacp port-number front-panel | no lacp port-number front-panel

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
port-number	Configure port-number in LACP port-channels
front-panel	Configure front panel based port numbering for LACP port-channels

Command Mode

/exec/configure

lacp port-priority

lacp port-priority <port-pri> | no lacp port-priority

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
port-priority	Set LACP port priority
port-pri	Enter port priority

Command Mode

/exec/configure/if-eth-base /exec/configure/if-ethernet-all

lacp rate

lacp rate <rate_type>

Syntax Description


lacp	Set LACP parameters for the interface
rate	Configure rate at which PDUs are sent by LACP
rate_type	Rate type

Command Mode

/exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-ethernet-m /exec/configure/if-ethernet-switch-m /exec/configure/if-remote-ethernet /exec/configure/if-remote-ethernet-switch

lacp rate

[no] lacp rate

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
rate	Configure rate at which PDUs are sent by LACP

Command Mode

/exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-ethernet-m /exec/configure/if-ethernet-switch-m /exec/configure/if-remote-ethernet /exec/configure/if-remote-ethernet-switch

lacp suspend-individual

lacp suspend-individual [ pxe ] | no lacp suspend-individual [ pxe ]

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
suspend-individual	Configure lacp port-channel state. Disabling this will cause lacp to put the port to individual state and not suspend the port in case it does not get LACP BPDU from the peer ports in the port-channel
pxe	(Optional) Disabling this would cause lacp to put only one port to individual state in case it does not get LACP BPDU from the peer port in the port-channel

Command Mode

/exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp system-mac

lacp system-mac <mac-address> [ role <role> ] | no lacp system-mac

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
system-mac	Configure the MAC address to be used for the LACP Protocol exchanges
mac-address	MAC-address(FORMAT :xxxx.xxxx.xxxx)
role	(Optional) Configure the role for this Switch
role	(Optional) Role played by the Switch

Command Mode

/exec/configure

lacp system-priority

lacp system-priority <sys-pri> | no lacp system-priority

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
system-priority	Set LACP system priority
sys-pri	Enter System Priority

Command Mode

/exec/configure

lacp vpc-convergence

lacp vpc-convergence | no lacp vpc-convergence

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
vpc-convergence	Enable lacp convergence for vPC port channels.

Command Mode

/exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

last

| last [ <lines> ]

Syntax Description


\|	Pipe command output to filter
last	Display last lines
lines	(Optional) number of lines to print

Command Mode

/output

latency

{ [ no ] latency <lat> | no latency }

Syntax Description


latency	Provide the latency value for this INT queue_profile
lat	queue_profile latency (nano seconds). Default is 2048 ns

Command Mode

/exec/configure/config-int-q-prof

latency

{ [ no ] latency <lat> | no latency }

Syntax Description


latency	Provide the latency value for this POSTCARD queue_profile
lat	queue_profile latency (nano seconds). Default is 2048 ns

Command Mode

/exec/configure/config-postcard-q-prof

latency quantization

{ [ no ] latency quantization <lat> | no latency quantization }

Syntax Description


latency	Provide the latency value for this POSTCARD flow-profile
quantization	Provide the latency value for this POSTCARD flow-profile
lat	flow-profile latency quantization. This value will be converted to a power of 2 (nanoseconds). For example, value of 11 will be converted to 2 power 11 which is 2048. This means that if the difference between ingress timestamp and egress timestamp is more than 2048 nanosec at any postcard in the path, one upstream report or local report will be generated per flow. The allowed values are in range 0-28. Default is 11.

Command Mode

/exec/configure/config-postcard-flow-prof

latency quantization

{ [ no ] latency quantization <lat> | no latency quantization }

Syntax Description


latency	Provide the latency value for this INT flow-profile
quantization	Provide the latency value for this INT flow-profile
lat	flow-profile latency quantization. This value will be converted to a power of 2 (nanoseconds). For example, value of 11 will be converted to 2 power 11 which is 2048. This means that if the difference between ingress timestamp and egress timestamp is more than 2048 nanosec at any point in the path, one upstream report or local report will be generated per flow. The allowed values are in range 0-28 Default is 11.

Command Mode

/exec/configure/config-int-flow-prof

layer-2 multicast lookup mac

[no] layer-2 multicast lookup mac

Syntax Description


no	(Optional) Negate a command or set its defaults
layer-2	set layer2 multicast lkup mode
multicast	set layer2 multicast lkup mode
lookup	lkup type can be either mac or ip based
mac	set mac based multicast lkup mode

Command Mode

/exec/configure/vlan-config /exec/configure/bdomain

layer2-switched flow monitor input

[no] layer2-switched flow monitor <monitorname> input

Syntax Description


layer2-switched	Configure L2 features
flow	NetFlow related commands
monitor	Apply a Flow Monitor to this interface
monitorname	Name of Flow Monitor
input	Apply Flow Monitor on input traffic

Command Mode

/exec/configure/if-switching

layer3 peer-router

layer3 peer-router | no layer3 peer-router

Syntax Description


no	Negate a command or set its defaults
layer3	Enable layer 3 functionality
peer-router	no change for TTL of packets destined to the peer

Command Mode

/exec/configure/vpc-domain

layer3 peer-router syslog

layer3 peer-router syslog [ interval <syslog-interval> ] | no layer3 peer-router syslog

Syntax Description


no	Negate a command or set its defaults
layer3	Enable layer 3 functionality
peer-router	no change for TTL of packets destined to the peer
syslog	print layer 3 protocol syslog
interval	(Optional) how frequent to print the syslog
syslog-interval	(Optional) how many seconds to print a syslog

Command Mode

/exec/configure/vpc-domain

lcnd push_to_klm address port vlan

lcnd push_to_klm address <macaddr> port <portnum> vlan <vlanid>

Syntax Description


lcnd	LCND configuration
push_to_klm	Push MAC address to auth_db
address	MAC address
macaddr	MAC address
port	Port number
portnum	Port number
vlan	VLAN id
vlanid	VLAN id

Command Mode

/exec/configure

ldap-search-map

ldap-search-map <s0>

Syntax Description


ldap-search-map	Set one of the configured search-map as active
s0	Name of the search-map

Command Mode

/exec/configure/ldap

ldap-search-map

[no] ldap-search-map

Syntax Description


no	Negate a command or set its defaults
ldap-search-map	Set one of the configured search-map as active

Command Mode

/exec/configure/ldap

ldap-server deadtime

[no] ldap-server deadtime <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
ldap-server	Configure LDAP related parameters
deadtime	Global LDAP server deadtime period in seconds
i0	LDAP server deadtime period in minutes (default 0 mins -disabled)

Command Mode

/exec/configure

ldap-server host

[no] ldap-server host { <hostipname> } [ { enable-ssl | port <i1> [ timeout <i2> ] | rootDN <s0> [ password { 7 <s1> | <s2> } ] [ port1 <i3> ] [ timeout1 <i4> ] | timeout2 <i5> | referral-disable } ]

Syntax Description


no	(Optional) Negate a command or set its defaults
ldap-server	Configure LDAP related parameters
host	LDAP server's DNS name or IP address
hostipname	IPV4/IPV6 address or DNS name
enable-ssl	(Optional) LDAP server enable ssl
port	(Optional) LDAP server's port (default: global config)
i1	(Optional) port number
timeout	(Optional) LDAP server timeout period in seconds
i2	(Optional) LDAP server timeout in seconds (default: global config)
rootDN	(Optional) LDAP server root DN
s0	(Optional) root DN
password	(Optional) LDAP server root password
7	(Optional) LDAP root password (encrypted)
s1	(Optional) password (encrypted)
s2	(Optional) password (clear text)
port1	(Optional) LDAP server's port (default: global config)
i3	(Optional) port number
timeout1	(Optional) LDAP server timeout period in seconds
i4	(Optional) LDAP server timeout in seconds (default: global config)
timeout2	(Optional) LDAP server timeout period in seconds
i5	(Optional) LDAP server timeout in seconds (default: global config)
referral-disable	(Optional) LDAP server disable referrals

Command Mode

/exec/configure

ldap-server host test rootDN

[no] ldap-server host { <hostipname> } test rootDN <r1> { { [ username <s0> { [ password { [ 7 <s2> | <s1> ] } [ idle-time <i1> ] ] | [ idle-time <i1> ] } ] } | { [ password { [ 7 <s2> | <s1> ] } [ idle-time <i1> ] ] } | { [ idle-time <i1> ] } }

Syntax Description


username	(Optional) <s0>
no	(Optional) Negate a command or set its defaults
ldap-server	Configure LDAP related parameters
host	LDAP server's IP address
hostipname	IPV4/IPV6 address or DNS name
test	Parameters to send test packets
7	(Optional) LDAP test password (encrypted)
s0	(Optional) user name
password	(Optional) user password in test packets
s1	(Optional) test password
s2	(Optional) test password (encrypted)
rootDN	rootDN in test packets
r1	root DN
idle-time	(Optional) time interval for monitoring the server
i1	(Optional) time period in minutes

Command Mode

/exec/configure

ldap-server timeout

[no] ldap-server timeout <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
ldap-server	Configure LDAP related parameters
timeout	Global LDAP server timeout period in seconds
i0	LDAP server timeout period in seconds (default 5 sec)

Command Mode

/exec/configure

ldap search-map

[no] ldap search-map <s0>

Syntax Description


no	(Optional) Negate a command or set its defaults
ldap	Configure information about ldap
search-map	Configure the search-map
s0	Search Map Name

Command Mode

/exec/configure

less

| less [ -d | -E ] +

Syntax Description


\|	Pipe command output to filter
less	Filter for paging
-d	(Optional) dumb terminal
-E	(Optional) quit at end of file

Command Mode

/output

license smart clear eventlog

Syntax Description


license	License related command
smart	Smart license related commands
clear	Clear
eventlog	Event log

Command Mode

/exec

license smart custom_id

license smart custom_id <s0> | no license smart custom_id

Syntax Description


no	Negate a command or set its defaults
license	License related command
smart	Smart license related commands
custom_id	Identifier to be added in utility RUM Report.
s0	Provide identifier

Command Mode

/exec/configure

license smart factory reset

Syntax Description


license	License related command
smart	Smart license related commands
factory	Smart license factory command
reset	Reset smart command

Command Mode

/exec

license smart import

license smart import <file>

Syntax Description


license	License related command
smart	Smart license related commands
import	Import or install authorization codes, policies, trust codes or ack from file
file	Specify URL for the file

Command Mode

/exec

license smart privacy

[no] license smart privacy { all | hostname | version }

Syntax Description


no	(Optional) Negate a command or set its defaults
license	License related command
smart	Smart license related commands
privacy	Set internal data privacy
hostname	Apply privacy setting for hostname
version	Apply privacy setting for SA version
all	Apply privacy setting for all data types

Command Mode

/exec/configure

license smart proxy address

license smart proxy { address <proxyadd> | port <proxyport> } | no license smart proxy { address | port }

Syntax Description


no	Negate a command or set its defaults
license	License related command
smart	Smart license related commands
proxy	Proxy related commands
address	The IP address or the hostname
proxyadd	Address/Hostname
port	The port
proxyport	Proxy port

Command Mode

/exec/configure

license smart save

license smart save { usage { all | days <n> | unreported | rum-Id <rum_id> } <file> | trust-request <file> }

Syntax Description


license	License related command
smart	Smart license related commands
save	Save RUM reports / trust request to a file offline
usage	Save RUM reports
all	Save all RUM reports
days	Save RUM reports for the last number of <days> specified
unreported	Save RUM reports not previously saved in file or sent
rum-Id	Save an individual RUM report
rum_id	RUM ID
trust-request	Generate trust request to save it a file
n	Specify number of days
file	Specify URL for the file

Command Mode

/exec

license smart sync local

license smart sync { local | all }

Syntax Description


license	License related command
smart	Smart license related commands
sync	Send any unsent RUM reports to the CSLU, controller REST endpoint or CSSM
local	Get codes for the current UDI
all	Get codes for all devices in HA config

Command Mode

/exec

license smart transport

license smart transport { callhome | smart | cslu | off } | no license smart transport

Syntax Description


no	Negate a command or set its defaults
license	License related command
smart	Smart license related commands
transport	set transport mode
callhome	Set the transport mode to callhome
smart	Set the transport mode to smart
cslu	Set the transport mode to cslu
off	Set the transport mode to off

Command Mode

/exec/configure

license smart trust idtoken local

license smart trust idtoken <s0> { local | all } [ force ]

Syntax Description


license	License related command
smart	Smart license related commands
trust	Establish trust with backend
idtoken	Use Trust Token to establish trust
s0	Provide id token received from backend
local	Establish trust with backend for Active SUP
all	Establish trust with backend for all SUPs
force	(Optional) Force backend to re-establish trust

Command Mode

/exec

license smart url smart

license smart url { smart | cslu } <url> | no license smart url { smart | cslu }

Syntax Description


no	Negate a command or set its defaults
license	License related command
smart	Smart license related command
url	Set the transport url
smart	Set smart transport url
cslu	Set CSLU URL
url	Provide http or https url, example1: http://site.com/services/callserv example2: https://site2.com/serv/CALL

Command Mode

/exec/configure

license smart usage interval

license smart usage interval <i0> | no license smart usage interval

Syntax Description


no	Negate a command or set its defaults
license	License related command
smart	Smart license related commands
usage	RUM reports
interval	Day for periodic RUM reports sending
i0	Reporting interval in days. Default 30 days

Command Mode

/exec/configure

limit-resource module-type

{ limit-resource module-type <card-type> + } | { no limit-resource module-type }

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
module-type	Controls which type of modules are allowed in this vdc
card-type	Allowed module types

Command Mode

/exec/configure/vdc

limit-resource monitor-session-erspan-dst minimum maximum equal-to-min

{ limit-resource monitor-session-erspan-dst minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session-erspan-dst [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description


limit-resource	Resource configuration
monitor-session-erspan-dst	Monitor erspan destination session
minimum	minimum monitor erspan-dst session to allocate
min-val	minimum monitor erspan-dst session value
maximum	maximum monitor erspan-dst session to allocate
max-val	maximum monitor erspan-dst session value
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource monitor-session-inband-src minimum maximum equal-to-min

{ limit-resource monitor-session-inband-src minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session-inband-src [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description


limit-resource	Resource configuration
monitor-session-inband-src	Monitor inband source
minimum	minimum monitor inband source to allocate
min-val	minimum monitor inband source value
maximum	maximum monitor inband source to allocate
max-val	maximum monitor inband source value
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource monitor-session minimum maximum equal-to-min

{ limit-resource monitor-session minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description


limit-resource	Resource configuration
monitor-session	Monitor local/erspan-source session
minimum	minimum monitor local session to allocate
min-val	minimum monitor local session value
maximum	maximum monitor local session to allocate
max-val	maximum monitor local session value
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource port-channel minimum maximum

limit-resource port-channel minimum <min-val> maximum { <max-val> | equal-to-min } | no limit-resource port-channel [ minimum <min-val> maximum { <max-val> | equal-to-min } ]

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
port-channel	set port-channel limits
minimum	minimum port-channels to allocate
min-val
maximum	maximum port-channels to allocate
max-val
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource vlan minimum maximum equal-to-min

{ limit-resource vlan minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource vlan [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
vlan	set VLAN limits
minimum	minimum VLANs to allocate
min-val	minimum VLANs value
maximum	maximum VLANs to allocate
max-val	maximum VLANs value
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource vrf minimum maximum equal-to-min

{ limit-resource vrf minimum <number1> maximum { <number2> | equal-to-min } } | { no limit-resource vrf [ minimum <number1> maximum { <number2> | equal-to-min } ] }

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
vrf	set vrf resource limits
minimum	minimum vrf resources to allocate
number1	minimum vrf resource value
maximum	maximum vrf resources to allocate
number2	maximum vrf resource value
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit address-count

[no] limit address-count <addr_count>

Syntax Description


no	(Optional) Negate a command or set its defaults
addr_count	maximum value

Command Mode

/exec/configure/config-snoop-policy

line console

[no] line console

Syntax Description


no	(Optional) Negate a command or set its defaults
line	Configure a terminal line
console	Primary terminal line

Command Mode

/exec/configure

line console

[no] line console

Syntax Description


no	(Optional) Negate a command or set its defaults
line	Configure a terminal line
console	Primary terminal line

Command Mode

/exec/configure

line vty

Syntax Description


line	Configure a terminal line
vty	Virtual terminal line

Command Mode

/exec/configure

link-level-flow-control watch-dog-interval on

[no] link-level-flow-control watch-dog-interval { on | off }

Syntax Description


no	(Optional) Negate the command
link-level-flow-control	Enable/Disable LLFC
watch-dog-interval	Watch dog interval
on	Enable LLFC watch-dog interval globally
off	Disable LLFC watch-dog interval globally

Command Mode

/exec/configure

link-state-trap

[no] link-state-trap

Syntax Description


no	(Optional) Negate a command or set its defaults
link-state-trap	Enable/disable link state change traps

Command Mode

/exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext /exec/configure/if-fcip /exec/configure/if-iscsi

link debounce

link debounce { [ link-up [ time <time_val_link_up> ] ] | [ time <time_val> ] } | no link debounce [ link-up ]

Syntax Description


no	Negate a command or set its defaults
link	Configure link
debounce	Configure link debounce timer
link-up	(Optional) Timer for the link-up event
time	(Optional) Link debounce time
time_val	(Optional) Timer value (in milliseconds)
time_val_link_up	(Optional) Timer value (in milliseconds)

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base

link dfe adaptive-tuning

{ link dfe adaptive-tuning | no link dfe adaptive-tuning }

Syntax Description


no	Negate a command or set its defaults
link	Configure link
dfe	Decision Feedback Equalizer
adaptive-tuning	Configure DFE adaptive tuning for interface

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base

link loopback

{ link loopback | no link loopback }

Syntax Description


no	Negate a command or set its defaults
link	configure link
loopback	configure the port to be in a loopback mode

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base

link mac-up timer

{ link mac-up timer <mac_up_timer_val> | no link mac-up timer }

Syntax Description


no	Negate a command or set its defaults
link	Configure link
mac-up	Configure link mac-up timer
timer	Link mac-up time
mac_up_timer_val	Timer value (in seconds)

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base

link transmit reset-skip

{ link transmit reset-skip | no link transmit reset-skip }

Syntax Description


no	Negate a command or set its defaults
link	Configure link
transmit	Configure link transmit for interface
reset-skip	Configure link transmit for interface

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base

lisp

{ lisp-lig | lig } { version | self | self6 | <hostname> | { <eid> | <eid6> } } [ source { <seid> | <seid6> } ] [ to { <mr-hostname> | { <mr> | <mr6> } } ] [ count <count> ] [ probe ] [ vrf { <vrf-name> | <vrf-known-name> } ]

Syntax Description


lisp-lig	LISP Internet Groper
lig	LISP Internet Groper
eid	LIG on a IPv4 Endpoint ID (EID)
version	Display Internet Draft version lig supports
self	Test if IPv4 EID-prefix registered in mapping database
self6	Test if IPv6 EID-prefix registered in mapping database
hostname	DNS name for Endpoint ID (EID)
source	(Optional) Provide source EID for Map-Request
seid	(Optional) Source IPv4 Endpoint ID (EID)
to	(Optional) Where to send the Map-Request
mr-hostname	(Optional) DNS name for Map-Resolver
mr	(Optional) Map-Resolver IPv4 address to send Map-Request to
count	(Optional) Map-Requests to send before Map-Reply returned
count	(Optional) Number of Map-Requests
probe	(Optional) RLOC-probe each locator
vrf	(Optional) LIGing for specific VRF
vrf-name	(Optional) VRF name
vrf-known-name	(Optional) Known VRF name

Command Mode

/exec

lisp ddt

{ [ no ] lisp ddt }

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
ddt	Configures a LISP-DDT mapping system functionality

Command Mode

/exec/configure /exec/configure/vrf

lisp ddt authoritative-prefix eid-prefix

{ [ no ] lisp ddt authoritative-prefix eid-prefix { <eid-prefix> | <eid-prefix6> } } | { [ no ] lisp ddt authoritative-prefix instance-id <iid> [ eid-prefix { <eid-prefix> | <eid-prefix6> } ] } | { [ no ] lisp ddt authoritative-prefix <star> } | { [ no ] lisp ddt authoritative-prefix instance-id { <iidp> | <range> } }

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
ddt	Configure LISP-DDT parameters
authoritative-prefix	Configure EID-prefix this LISP-DDT node is authoritative for
instance-id	Instance ID of VPN for EID-prefix
iid	Instance-ID value
star	Authoritative prefix on root for all address space
iidp	Instance-ID in prefix format
range	Instance-ID range in 'x-y' format where y > x
eid-prefix	Authoritative IPv4 or IPv6 EID-prefix
eid-prefix	EID-prefix in IPv4 slash format

Command Mode

/exec/configure /exec/configure/vrf

lisp ddt delegate eid-prefix

{ [ no ] lisp ddt delegate { <node> | <node6> } { eid-prefix { <eid-prefix> | <eid-prefix6> } } [ priority <priority> weight <weight> ] [ public-key <key> ] [ map-server ] } | { [ no ] lisp ddt delegate { <node> | <node6> } instance-id <iid> [ eid-prefix { <eid-prefix> | <eid-prefix6> } ] [ priority <priority> weight <weight> ] [ public-key <key> ] [ map-server ] } | { [ no ] lisp ddt delegate { <node> | <node6> } instance-id { <iidp> | <range> } [ priority <priority> weight <weight> ] [ public-key <key> ] [ map-server ] }

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
ddt	Configure LISP-DDT parameters
delegate	Configure LISP-DDT child in delegation hierarchy
node	IPv4 locator address of DDT node
instance-id	Instance ID of VPN for EID-prefix
iid	Instance-ID value
iidp	Instance-ID in prefix format
range	Instance-ID range in 'x-y' format where y > x
eid-prefix	Child delegration for IPv4 or IPv6 EID-prefix
eid-prefix	EID-prefix in IPv4 slash format
priority	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED
priority	(Optional) Lower priority Locator takes preference
weight	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED
weight	(Optional) Specified in a percentage from 0 to 100
map-server	(Optional) Child delegate is a Map-Server
public-key	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED
key	(Optional) RSA public-key

Command Mode

/exec/configure /exec/configure/vrf

lisp ddt map-server-peer eid-prefix

{ [ no ] lisp ddt map-server-peer { <node> | <node6> } { eid-prefix { <eid-prefix> | <eid-prefix6> } } [ priority <priority> weight <weight> ] [ public-key <key> ] } | { [ no ] lisp ddt map-server-peer { <node> | <node6> } instance-id <iid> [ eid-prefix { <eid-prefix> | <eid-prefix6> } ] [ priority <priority> weight <weight> ] [ public-key <key> ] } | { [ no ] lisp ddt map-server-peer { <node> | <node6> } instance-id { <iidp> | <range> } [ priority <priority> weight <weight> ] [ public-key <key> ] }

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
ddt	Configure LISP-DDT parameters
map-server-peer	Configure other map-server peers
node	IPv4 locator address of DDT node
instance-id	Instance ID of VPN for EID-prefix
iid	Instance-ID value
iidp	Instance-ID in prefix format
range	Instance-ID range in 'x-y' format where y > x
eid-prefix	Child delegration for IPv4 or IPv6 EID-prefix
eid-prefix	EID-prefix in IPv4 slash format
priority	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED
priority	(Optional) Lower priority Locator takes preference
weight	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED
weight	(Optional) Specified in a percentage from 0 to 100
public-key	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED
key	(Optional) RSA public-key

Command Mode

/exec/configure /exec/configure/vrf

lisp ddt root

[no] lisp ddt root { <root> | <root6> } [ public-key <key> ]

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
ddt	Configure LISP-DDT parameters
root	Configure LISP-DDT root of tree in Map-Resolver
root	IPv4 locator address of DDT root
public-key	(Optional) DDT root's public key used to verify signed Map-Referrals
key	(Optional) RSA public-key

Command Mode

/exec/configure /exec/configure/vrf

lisp dynamic-eid

{ [ no ] lisp dynamic-eid <dyn-eid-name> }

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
dynamic-eid	Configure dynamic-EIDs for roaming
dyn-eid-name	Name your dynamic-EID

Command Mode

/exec/configure/vrf

lisp dynamic-eid

{ [ no ] lisp dynamic-eid <dyn-eid-name> }

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
dynamic-eid	Configure dynamic-EIDs for roaming
dyn-eid-name	Name your dynamic-EID

Command Mode

/exec/configure

lisp explicit-locator-path

[no] lisp explicit-locator-path <elp-name>

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
explicit-locator-path	Configures a LISP Explicit Locator Path (ELP)
elp-name	Name of LISP ELP

Command Mode

/exec/configure/vrf

lisp explicit-locator-path

{ [ no ] lisp explicit-locator-path <elp-name> }

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
explicit-locator-path	Configures a LISP Explicit Locator Path (ELP)
elp-name	Name of LISP ELP

Command Mode

/exec/configure

lisp extended-subnet-mode

{ [ no ] lisp extended-subnet-mode }

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP interface configuration commands
extended-subnet-mode	Create dynamic-EID state when EIDs reside on their home subnet

Command Mode

/exec/configure/if-igp

lisp geo-coordinates

[no] lisp geo-coordinates <latitude> <longitude> [ <altitude> ]

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
geo-coordinates	Configure Geo Coordinates for this router
latitude	Latitude in DMS format: 'degree-min-sec-N' or 'degree-min-sec-S
longitude	Longitude in DMS format: 'degree-min-sec-E' or 'degree-min-sec-W format
altitude	(Optional) Altitude in meters above sea-level

Command Mode

/exec/configure /exec/configure/vrf

lisp instance-id

[no] lisp instance-id <iid>

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
instance-id	Configures Instance-ID for global data-mappings
iid	24-bit instance-ID value

Command Mode

/exec/configure /exec/configure/vrf

lisp loc-reach-algorithm

[no] lisp loc-reach-algorithm { count-tcp | echo-nonce | { rloc-probing [ map-request-on-failure ] } }

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
loc-reach-algorithm	Configure locator reachability algorithm
count-tcp	Count TCP SYNs and ACKs
echo-nonce	Request for nonce to echo back in data-plane
rloc-probing	Probe each high-priority RLOC with Map-Request as last resort
map-request-on-failure	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

/exec/configure /exec/configure/vrf

lisp merge-registrations site-id

[no] lisp merge-registrations site-id <site-id>

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
merge-registrations	ETRs merge registrations from Map-Notify messages
site-id	Configure site-id value for each xTR at site
site-id	Site-ID to group xTRs together

Command Mode

/exec/configure /exec/configure/vrf

lisp mobility

[no] lisp mobility <dyn-eid-name>

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP interface configuration commands
mobility	Configures to allow EID mobility on interface
dyn-eid-name	Name of the dynamic-EID to use

Command Mode

/exec/configure/if-igp

lisp mobility test-liveness

[no] lisp mobility test-liveness

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP interface configuration commands
mobility	Configures to allow EID mobility on interface
test-liveness	Ping discovered dyn-eid hosts on this interface periodically to determine host liveness

Command Mode

/exec/configure/if-igp

lisp security

[no] lisp security [ strong ]

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
security	Configure LISP-SEC on ITR or PITR
strong	(Optional) Reject Map-Replies without LISP-SEC signatures included

Command Mode

/exec/configure /exec/configure/vrf

lisp site

{ [ no ] lisp site <site-name> }

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
site	Configures LISP sites in a map-server
site-name	Name your LISP site

Command Mode

/exec/configure/vrf

lisp site

{ [ no ] lisp site <site-name> }

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
site	Configures LISP sites in a map-server
site-name	Name your LISP site

Command Mode

/exec/configure

lisp smr-locators

[no] lisp smr-locators

Syntax Description


no	(Optional) Negate a command or set its defaults
lisp	LISP global configuration commands
smr-locators	Send SMR to all RLOCs in locator-set for map-cache entry

Command Mode

/exec/configure

lisp to

{ lisp-rig | rig } [ instance-id <iid> ] { <hostname> | { <eid> | <eid6> } } to { <ddt-hostname> | { <ddt> | <ddt6> } }

Syntax Description


lisp-rig	LISP-DDT Referral Internet Groper
rig	LISP-DDT Referral Internet Groper
instance-id	(Optional) Instance-ID of VPN EID resides in
iid	(Optional) 24-bit instance-ID value
eid	RIG on a IPv4 Endpoint ID (EID)
hostname	DNS name for Endpoint ID (EID)
to	Where to send the Map-Request
ddt-hostname	DNS name for DDT-node
ddt	DDT-node IPv4 address to send Map-Request to

Command Mode

/exec

listobject-boolean not

listobject-boolean <obj-id> not

Syntax Description


listobject-boolean	Configure Object as member of tracking list
obj-id	Tracked object
not	Negate Up status

Command Mode

/exec/configure/tr-list-bool

listobject-weight weight threshold-weight

listobject-weight { <obj-id> weight <weight-val> } | threshold-weight { weight-thresh { weightup <up-weight> [ weightdown <down-weight> ] | weightdown <down-weight> [ weightup <up-weight> ] } } | no threshold-weight weight-thresh

Syntax Description


no	Negate a command or set its defaults
listobject-weight	Configure Object as member of tracking list
obj-id	Tracked Object
weight	Assign a weight to object
weight-val	Assign a weight to object
threshold-weight	Threshold parameters
weight-thresh	Weight threshold
weightup	Up threshold
up-weight	Up threshold weight
weightdown	(Optional) Down threshold
down-weight	(Optional) Down threshold weight

Command Mode

/exec/configure/tr-list-thrw

listobject

[no] listobject <obj-id>

Syntax Description


no	(Optional) Negate a command or set its defaults
listobject	Configure Object as member of tracking list
obj-id	Tracked Object

Command Mode

/exec/configure/tr-list-thrw /exec/configure/tr-list-thrp /exec/configure/tr-list-bool

liveness-detection

[no] liveness-detection

Syntax Description


no	(Optional) Negate a command or set its defaults
liveness-detection	Configure color specific liveness detection related configurations

Command Mode

/exec/configure/sr/te/color

liveness-detection

[no] liveness-detection

Syntax Description


no	(Optional) Negate a command or set its defaults
liveness-detection	Configure Traffic Engineering Segment Routing liveness detection related configurations

Command Mode

/exec/configure/sr/te

liveness-detection

[no] liveness-detection

Syntax Description


no	(Optional) Negate a command or set its defaults
liveness-detection	Configure color specific liveness detection related configurations

Command Mode

/exec/configure/sr/te/pol

lldp

[no] lldp { holdtime <i0> | reinit <i1> | timer <i2> | portid-subtype <i3> | tlv-select { management-address | port-description | port-vlan | power-management | system-capabilities | system-description | system-name | dcbxp | four-wire-power-management } | port-channel | multi-neighbor }

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure global LLDP parameters
holdtime	Specify the holdtime (in sec) to be sent in packets
i0	holdtime in sec
reinit	Delay (in sec) for LLDP initialisation on any interface
i1	reinit in sec
timer	Specify the rate at which LLDP packets are sent (in sec)
i2	rate of packets in sec
portid-subtype	config portid subtype for LLDP TLV and SNMP MIBs
i3	0: long interface name (default), 1: short interface name
tlv-select	Selection of LLDP to send
management-address	Management Address TLV
port-description	Port Description TLV
port-vlan	Port Vlan ID TLV
power-management	IEEE 802.3 DTE Power via MDI TLV
system-capabilities	System Capabilities TLV
system-description	System Description TLV
system-name	System Name TLV
dcbxp	DCBXP TLVs
four-wire-power-management	Cisco 4-wire Power via MDI TLV
port-channel	Enable LLDP on Port-channel
multi-neighbor	Enable multiple LLDP neighbors per interface

Command Mode

/exec/configure

lldp dcbx version auto

Syntax Description


lldp	Configure LLDP parameters
dcbx	Configure DCBX parameters
version	Change the DCBX protocol version
auto	Auto-detect the DCBX version

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp dcbx version cee

[no] lldp dcbx version { cee | ieee }

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure LLDP parameters
dcbx	Configure DCBX parameters
version	Change the DCBX protocol version
cee	The CEE version of DCBX
ieee	The IEEE 802.1 version of DCBX

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp receive

[no] lldp receive

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure Interface LLDP parameters
receive	Enable LLDP reception on interface

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether /exec/configure/if-vethernet /exec/configure/if-veth-any /exec/configure/if-veth-all /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-switch

lldp tlv-select management-address v4

[no] lldp tlv-select management-address { v4 | v6 }

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure global LLDP parameters
tlv-select	Selection of LLDP to send
management-address	Management Address TLV
v4	Management Address TLV v4
v6	Management Address TLV v6

Command Mode

/exec/configure

lldp tlv-set management-address

[no] lldp tlv-set management-address <ip-addr>

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure Interface LLDP parameters
tlv-set	LLDP TLV configuration for interface
management-address	Management address to be sent in management-tlv of LLDPDU.
ip-addr	IP address in dotted decimal format i.i.i.i

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp tlv-set management-address ipv6

[no] lldp tlv-set management-address <ipv6-addr> ipv6

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure Interface LLDP parameters
tlv-set	LLDP TLV configuration for interface
management-address	Management address to be sent in management-tlv of LLDPDU.
ipv6	IPV6

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp tlv-set vlan

[no] lldp tlv-set vlan [ <vlan-id> ]

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure Interface LLDP parameters
tlv-set	LLDP TLV configuration for interface
vlan	VLAN-id whose SVI IP address should be used as management adrress in management-tlv of LLDPDU. Default is native VLAN.
vlan-id	(Optional) vlan-id within range of 1-4094

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp transmit

[no] lldp transmit

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure Interface LLDP parameters
transmit	Enable LLDP transmission on interface

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether /exec/configure/if-vethernet /exec/configure/if-veth-any /exec/configure/if-veth-all /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-switch

load-balance

[no] load-balance { { { method <lb-method> } | { buckets <buckets> } } + }

Syntax Description


no	(Optional) Negate a command or set its defaults
load-balance	Loadbalance options for this match
method	Loadbalance method
lb-method	Loadbalance method options
buckets	Buckets for traffic distribution - this should be in powers of 2
buckets	Loadbalance bucket count

Command Mode

/exec/configure/epbr-sess-policy/action

load-balance

[no] load-balance { { { method <lb-method> } | { buckets <buckets> } } + }

Syntax Description


no	(Optional) Negate a command or set its defaults
load-balance	Loadbalance options for this match
method	Loadbalance method
lb-method	Loadbalance method options
buckets	Buckets for traffic distribution - this should be in powers of 2
buckets	Loadbalance bucket count

Command Mode

/exec/configure/epbr-policy/action

load-balance

[no] load-balance { { method { src { ip | ip-l4port <src-protocol> range <src-x> <src-y> } | dst { ip-dst | ip-l4port <dst-protocol> range <dst-x> <dst-y> } } | { buckets <num> } | { mask-position <mask> } | { least-bit } } + }

Syntax Description


no	(Optional) Negate a command or set its defaults
load-balance	ITD Loadbalance
method	ITD Loadbalance method
src	Source based parameters
dst	Destination based parameters
ip	IP
ip-l4port	IP and L4 port
src-protocol	Protocol
range	Match only packets in the range of port numbers
src-x
src-y
ip-dst	IP
dst-protocol	Protocol
dst-x
dst-y
buckets	Used to create the buckets for traffic distribution, and it should be in powers of 2
num	Loadbalance bucket number
mask-position	Loadbalance mask position
mask	Loadbalance mask position number range 0-31 for IPv4 and 0-127 for IPv6
least-bit	Craft load-balancing masks beginning at the least significant bits

Command Mode

/exec/configure/itd

load-interval

load-interval <interval> | no load-interval [ <interval1> ]

Syntax Description


no	Negate a command or set its defaults
load-interval	Specify interval for load calculation for an interface
interval	Load interval delay in seconds
interval1	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

/exec/configure/if-vlan-common

load-interval

load-interval <interval> | no load-interval [ <interval1> ]

Syntax Description


no	Negate a command or set its defaults
load-interval	Specify interval for load calculation for an interface
interval	Load interval delay in seconds
interval1	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel

load-interval counter

load-interval counter <counter_val> <interval> | no load-interval counter <counter_val> [ <interval1> ]

Syntax Description


no	Negate a command or set its defaults
load-interval	Specify interval for load calculation for an interface
counter	Specify counter for this load interval
interval	Load interval delay in seconds
counter_val	Specify counter for this load interval
interval1	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

/exec/configure/if-vlan-common

load-interval counter

load-interval counter <counter_val> <interval> | no load-interval counter <counter_val> [ <interval1> ]

Syntax Description


no	Negate a command or set its defaults
load-interval	Specify interval for load calculation for an interface
counter	Specify counter for this load interval
counter_val	Specify counter for this load interval
interval	Load interval delay in seconds
interval1	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel

load

load <uri0>

Syntax Description


load	Load system image
uri0	Enter image URI

Command Mode

/exec

load

load <uri0> [ <s0> ]

Syntax Description


load	Load system image
uri0	Enter image URI
s0	(Optional) Options

Command Mode

/exec

load

load <uri0> [ <s0> ]

Syntax Description


load	Load system image
uri0	Enter image URI
s0	(Optional) Options

Command Mode

/exec

load configuration failed commit

Syntax Description


load	Load the configuration
configuration	Contents of configuration
failed	Load failed configuration
commit	Failed configuration from last commit

Command Mode

/exec/configure

local-as

{ local-as <asn> [ no-prepend [ replace-as [ dual-as ] ] ] } | { { no | default } local-as [ <asn> ] }

Syntax Description


no	Negate a command or set its defaults
default	Inherit values from a peer template
local-as	Specify the local-as number for the eBGP neighbor
asn	Autonomous System Number
no-prepend	(Optional) Do not prepend the local-as number to updates from the eBGP neighbor
replace-as	(Optional) Prepend only the local-as number to updates to eBGP neighbor
dual-as	(Optional) Connect using either the local-as number or the real as

Command Mode

/exec/configure/router-bgp/router-bgp-neighbor-sess

local-as

local-as <asn> | no local-as [ <asn> ]

Syntax Description


no	Negate a command or set its defaults
local-as	Specify the local-as for this vrf
asn	AS number

Command Mode

/exec/configure/router-bgp/router-bgp-vrf

local-label prefix

[no] { [ vrf { <vrf-name> | <vrf-known-name> } ] local-label <static-inlabel> prefix { <prefix> <mask> | <prefix-mask> } }

Syntax Description


no	(Optional) Negate a command or set its defaults
vrf	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED
vrf-name	(Optional) VRF name
vrf-known-name	(Optional) Known VRF name
local-label	Configure local label assignment and forwarding
static-inlabel	Label Value
prefix	For a given prefix
prefix	Destination prefix
mask	Destination prefix mask
prefix-mask	Destination prefix/mask

Command Mode

/exec/configure/mpls_static/ipv4

local-label prefix

[no] { [ vrf { <vrf-name> | <vrf-known-name> } ] local-label <static-inlabel> prefix { <ipv6-prefix-mask> } }

Syntax Description


no	(Optional) Negate a command or set its defaults
vrf	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED
vrf-name	(Optional) VRF name
vrf-known-name	(Optional) Known VRF name
local-label	Configure local label assignment and forwarding
static-inlabel	Label Value
prefix	For a given prefix

Command Mode

/exec/configure/mpls_static/ipv6

locator-led

[no] locator-led { chassis | module <module> | fan <fan_num> }

Syntax Description


no	(Optional) Negate a command or set its defaults
locator-led	blink locator led on device
chassis	blink chassis led
module	blink module led
module	please enter the module number
fan	blink Fan led
fan_num	fan number

Command Mode

/exec

locator

[no] locator <locator-name>

Syntax Description


no	(Optional) Negate a command or set its defaults
locator	Configure SRv6 locator name
locator-name	Locator name to advertise

Command Mode

/exec/configure/router-isis/router-isis-af-ipv6/srv6

locator

[no] locator <name>

Syntax Description


no	(Optional) Negate a command or set its defaults
locator	Configure an SRv6 locator for this node
name	Name for the locator

Command Mode

/exec/configure/sr/srv6/locators

locator

[no] locator <locator-name>

Syntax Description


no	(Optional) Negate a command or set its defaults
locator	Specify the locator
locator-name	Locator name

Command Mode

/exec/configure/router-bgp/router-bgp-srv6

locator

[no] locator <locator-name>

Syntax Description


no	(Optional) Negate a command or set its defaults
locator	Configure Traffic Engineering Segment Routing V6 locator
locator-name	Configure locator name

Command Mode

/exec/configure/sr/te/sr/srv6/locs

locators

[no] locators

Syntax Description


no	(Optional) Negate a command or set its defaults
locators	Configure Traffic Engineering Segment Routing V6 locator configurations

Command Mode

/exec/configure/sr/te/sr/srv6

locators

[no] locators

Syntax Description


no	(Optional) Negate a command or set its defaults
locators	Base to configure SRv6 locators

Command Mode

/exec/configure/sr/srv6

log-adjacency-changes

[no] log-adjacency-changes [ detail ]

Syntax Description


no	(Optional) Negate a command or set its defaults
log-adjacency-changes	Log changes in adjacency state
detail	(Optional) Notify all state changes

Command Mode

/exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

log-adjacency-changes

[no] log-adjacency-changes

Syntax Description


no	(Optional) Negate a command or set its defaults
log-adjacency-changes	Log changes in adjacency state

Command Mode

/exec/configure/router-isis/router-isis-vrf-common

log-adjacency-changes

[no] log-adjacency-changes [ detail ]

Syntax Description


no	(Optional) Negate a command or set its defaults
log-adjacency-changes	Log changes in adjacency state
detail	(Optional) Notify all state changes

Command Mode

/exec/configure/router-ospf /exec/configure/router-ospf/vrf

log-adjacency-changes

[no] log-adjacency-changes

Syntax Description


no	(Optional) Negate a command or set its defaults
log-adjacency-changes	Log changes in adjacency state

Command Mode

/exec/configure/otv-isis/otv-isis-vrf-common

log-adjacency-changes

[no] log-adjacency-changes

Syntax Description


no	(Optional) Negate a command or set its defaults
log-adjacency-changes	Log changes in adjacency state

Command Mode

/exec/configure/l2mp-isis/l2mp-isis-vrf-common

log-neighbor-changes

[ no | default ] log-neighbor-changes [ disable ]

Syntax Description


no	(Optional) Negate a command or set its defaults
default	(Optional) Inherit values from a peer template
log-neighbor-changes	Log message for neighbor up/down event
disable	(Optional) Disable logging of neighbor up/down event

Command Mode

/exec/configure/router-bgp/router-bgp-neighbor-sess

log-neighbor-changes

[no] log-neighbor-changes

Syntax Description


no	(Optional) Negate a command or set its defaults
log-neighbor-changes	Log a message for neighbor up/down event

Command Mode

/exec/configure/router-bgp/vrf-cmds

log-neighbor-warnings

{ { [ eigrp ] log-neighbor-warnings [ <interval> ] } | { no [ eigrp ] log-neighbor-warnings [ <interval> ] } }

Syntax Description


no	Negate a command or set its defaults
eigrp	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED
log-neighbor-warnings	Enable/Disable IP-EIGRP neighbor warnings
interval	(Optional) Neighbor warning interval in seconds

Command Mode

/exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

logging

[no] logging { neighbor-changes |

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Enable LDP logging
neighbor-changes	Log LDP neighbor state changes

Command Mode

/exec/configure/ldp

logging abort

Syntax Description


logging	Modify message logging facilities
abort	Flushes cached data without committing and releases the lock

Command Mode

/exec/configure

logging console

[no] logging console [ <i0> ]

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
console	Set console logging
i0	(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging distribute

[no] logging distribute

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
distribute	Enables/disables fabric distribution using cfs.

Command Mode

/exec/configure

logging drop threshold

logging drop { threshold-packets <threshold-in-packets> | threshold-bytes <threshold-in-bytes> } [ level <level-value> ]

Syntax Description


logging	set logging for copp class
drop	logging for copp drops
threshold-packets	threshold value for dropped packets
threshold-bytes	threshold value for dropped bytes
level	(Optional) syslog level
level-value	(Optional) specify the logging level between 1-7

Command Mode

/exec/configure/pmap/class

logging drop threshold

[no] logging drop { threshold-packets <threshold-in-packets> | threshold-bytes <threshold-in-bytes> } [ level <level-value> ]

Syntax Description


no	Negate a command or set its defaults
logging	set logging for copp class
drop	logging for copp drops
threshold-packets	threshold value for dropped packets
threshold-bytes	threshold value for dropped bytes
level	(Optional) syslog level
level-value	(Optional) specify the logging level between 1-7

Command Mode

/exec/configure/pmap/class

logging event link enable

[no] logging event { link-status | trunk-status } { enable | default }

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Configure logging for interface
event	Interface events
link-status	UPDOWN and CHANGE messages
trunk-status	TRUNK status messages
enable	To enable logging overriding port level configuration
default	default logging configuration used by interfaces not explicitly configured

Command Mode

/exec/configure

logging event port link-status

[no] logging event port link-status

Syntax Description


no	Negate a command or set its defaults
logging	Configure logging for interface
event	Interface events
port	Port level events
link-status	UPDOWN and CHANGE messages

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-ether-sub-switch /exec/configure/if-port-channel-sub-switch /exec/configure/if-remote-ethernet-sub /exec/configure/if-ether-sub-p2p

logging event port link-status

Syntax Description


logging	Configure logging for interface
event	Interface events
port	Port level events
link-status	UPDOWN and CHANGE messages

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-ether-sub-switch /exec/configure/if-port-channel-sub-switch /exec/configure/if-remote-ethernet-sub /exec/configure/if-ether-sub-p2p

logging event port link-status

logging event port link-status [ default ] | no logging event port link-status

Syntax Description


no	Negate a command or set its defaults
logging	Configure logging for interface
event	Interface events
port	Port level events
link-status	UPDOWN and CHANGE messages
default	(Optional) Use the global default value

Command Mode

/exec/configure/if-loopback

logging event port link-status default

Syntax Description


logging	Configure logging for interface
event	Interface events
port	Port level events
link-status	UPDOWN and CHANGE messages
default	Use the global default value

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-ether-sub-switch /exec/configure/if-port-channel-sub-switch /exec/configure/if-remote-ethernet-sub /exec/configure/if-ether-sub-p2p

logging event port trunk-status

Syntax Description


logging	Configure logging for interface
event	Interface events
port	Port level events
trunk-status	TRUNK status messages

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port trunk-status

[no] logging event port trunk-status

Syntax Description


no	Negate a command or set its defaults
logging	Configure logging for interface
event	Interface events
port	Port level events
trunk-status	TRUNK status messages

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port trunk-status default

Syntax Description


logging	Configure logging for interface
event	Interface events
port	Port level events
trunk-status	TRUNK status messages
default	Use the global default value

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging flow-mod

[no] logging flow-mod

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Enable logging
flow-mod	Enable logging for flow-modify

Command Mode

/exec/configure/openflow/switch

logging flow-mod

[no] logging flow-mod

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Enable logging
flow-mod	Enable logging for flow-modify

Command Mode

/exec/configure/openflow/switch/sub-switch

logging history

{ logging history { <i0> | size <i1> } | no logging history [ size ] }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
history	Modifies severity level or size for history table
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
size	Modifies history table size
i1	Enter history table size

Command Mode

/exec/configure

logging ip access-list cache

[no] logging ip access-list cache { { interval <seconds> } }

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
ip	IP configuration
access-list	Access-list
cache	logging
interval	Log-update interval (in sec)
seconds	Log-update interval in seconds

Command Mode

/exec/configure

logging ip access-list cache entries

[no] logging ip access-list cache { { entries <num_entries> } | { threshold <num_packets> } }

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
ip	IP configuration
access-list	Access-list
cache	logging
entries	Maximum number of log entries cached in software
num_entries	Number of entries
threshold	Log-update threshold
num_packets	Log-update threshold (number of hits)

Command Mode

/exec/configure

logging ip access-list detailed

[no] logging ip access-list detailed

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Enable detailed logging
ip	configured IP
access-list	Access-list
detailed	Detailed ACL information

Command Mode

/exec/configure

logging ip access-list include sgt

[no] logging ip access-list include sgt

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
ip	IP configuration
access-list	Access-list
include	Include additional fields in syslogs
sgt	Include source group tag info in syslogs

Command Mode

/exec/configure

logging level

[no] logging level { xml server | xmlma } <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
xml	xml agent
server	xml agent server
xmlma	xml master agent. Same as combination of keywords xml server
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level

[no] logging level { { routing ipv6 multicast } | m6rib } <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
routing	Configure routing information
ipv6	Display IPv6 information
multicast	Set syslog filter level for M6RIB
m6rib	Set syslog filter level for M6RIB
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level

{ logging level { auth <i1> | authpriv <i2> | cron <i3> | daemon <i4> | ftp <i5> | kernel <i6> | local0 <i7> | local1 <i8> | local2 <i9> | local3 <i10> | local4 <i11> | local5 <i12> | local6 <i13> | local7 <i14> | lpr <i15> | mail <i16> | news <i17> | syslog <i18> | user <i19> | uucp <i20> } | no logging level { auth [ <i1> ] | authpriv [ <i2> ] | cron [ <i3> ] | daemon [ <i4> ] | ftp [ <i5> ] | kernel [ <i6> ] | local0 [ <i7> ] | local1 [ <i8> ] | local2 [ <i9> ] | local3 [ <i10> ] | local4 [ <i11> ] | local5 [ <i12> ] | local6 [ <i13> ] | local7 [ <i14> ] | lpr [ <i15> ] | mail [ <i16> ] | news [ <i17> ] | syslog [ <i18> ] | user [ <i19> ] | uucp [ <i20> ] } }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
auth	Set level for Authorization System
i1	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
authpriv	Set level for Authorization (Private) system
i2	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
cron	Set level for Cron/at facility
i3	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
daemon	Set level for System daemons
i4	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
ftp	Set level for File Transfer System
i5	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
kernel	Set level for kernel
i6	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
local0	Set level for Local use daemons
i7	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
local1	Set level for Local use daemons
i8	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
local2	Set level for Local use daemons
i9	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
local3	Set level for Local use daemons
i10	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
local4	Set level for Local use daemons
i11	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
local5	Set level for Local use daemons
i12	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
local6	Set level for Local use daemons
i13	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
local7	Set level for Local use daemons
i14	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
lpr	Set level for Line Printer System
i15	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
mail	Set level for Mail system
i16	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
news	Set level for USENET news
i17	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
syslog	Set level for Internal Syslog Messages
i18	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
user	Set level for User Process
i19	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
uucp	Set level for Unix-to-Unix copy system
i20	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level

[no] logging level { { routing [ ip | ipv4 ] multicast } | mrib } <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
routing	Configure routing information
ip	(Optional) Configure IP features
ipv4	(Optional) Configure IP features
multicast	Set syslog filter level for MRIB
mrib	Set syslog filter level for MRIB
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level aaa

logging level aaa <i0> | no logging level aaa [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
aaa	Set level for aaa syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level acl

[no] logging level acl <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
acl	Set syslog filter level for acl manager
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level acllog

logging level acllog <i0> | no logging level acllog [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
acllog	Set level for acllog syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level aclmgr

[no] logging level aclmgr <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
aclmgr	Set level for aclmgr syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level adbm

[no] logging level adbm <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
adbm	Set level for adbm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level adjmgr

[no] logging level adjmgr <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
adjmgr	Set syslog filter level for Adjacency Manager
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level all

{ logging level { all <i0> } | no logging level { all [ <i0> ] } }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
all	Set level for all facilities
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level amt

[no] logging level amt <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
amt	Set syslog filter level for AMT
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level arp

{ logging level arp <level> } | { no logging level arp [ <level> ] }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
arp	Set syslog filter level for ARP
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ascii-cfg

[no] logging level ascii-cfg <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ascii-cfg	Set logging level for ascii-cfg
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level assoc_mgr

[no] logging level assoc_mgr <i0> | no logging level assoc_mgr [ <i0> ]

Syntax Description


no	(Optional) Negate a command or set its default
logging	Show logging configuration and contents of logfile
level	Show facility logging configuration
assoc_mgr	Show Association Manager Logging Configuration
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level backup

[no] logging level { backup | flexlink } <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
backup	Set level for Switchport Backup syslog messages
flexlink	Set level for Switchport Backup syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level bfd

[no] logging level bfd <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
bfd	Set level for bfd syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level bgp

[no] logging level bgp <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
bgp	Set syslog filter level for BGP
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level bloggerd

[no] logging level bloggerd <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
bloggerd	Set level for BloggerD syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level bootvar

[no] logging level bootvar <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
bootvar	Set level for bootvar
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level callhome

logging level callhome <i0> | no logging level callhome [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
callhome	Callhome syslog level
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level capability

[no] logging level capability <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
capability	Set syslog level for mig utils daemon
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level cdp

logging level cdp <i0> | no logging level cdp [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
cdp	Set level for CDP syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level cfs

[no] logging level cfs <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level clis

[no] logging level clis <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
clis	Set syslog filter level for CLIS
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level clk_mgr

[no] logging level clk_mgr <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
clk_mgr	Set level for clock manager syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level confcheck

{ logging level confcheck <i0> | no logging level confcheck [ <i0> ] }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level copp

logging level copp <i0> | no logging level copp [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
copp	Set level for copp syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level core-dmon

{ logging level core-dmon <i0> | no logging level core-dmon [ <i0> ] }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
core-dmon	core daemon syslog level
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level cts

[no] logging level cts <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
cts	Set level for cts syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level device-alias

[no] logging level device-alias <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
device-alias	Set syslog level for Device Alias Distribution Service
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level dhclient

[no] logging level dhclient <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
dhclient	Set level for dhcp client syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level dhcp_snoop

logging level dhcp_snoop <level> | no logging level dhcp_snoop [ <level> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
dhcp_snoop	Set level for dhcp snoop syslog messages
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level diagclient

[no] logging level diagclient <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
diagclient	Set level for GOLD DiagClient syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level diagmgr

[no] logging level diagmgr <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
diagmgr	Set level for GOLD DiagMgr syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level dot1x

logging level dot1x <i0> | no logging level dot1x [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
dot1x	Set level for dot1x syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level dpvm

[no] logging level dpvm <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
dpvm	Set syslog level for DPVM
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ecp

[no] logging level ecp <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ecp	Set syslog filter level for ECP
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level eigrp

[no] logging level eigrp [ <eigrp-ptag> ] <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
eigrp	Set syslog filter level for EIGRP
eigrp-ptag	(Optional) Process tag
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level eltm

logging level eltm <i0> | no logging level eltm

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
eltm	Set level for eltm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level epbr

[no] logging level epbr <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
epbr	Set level for epbr syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level epp

[no] logging level epp <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
epp	Set level for EPP syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ethpm

[no] logging level ethpm <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ethpm	Set level for ethpm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ethpm link

[no] logging level ethpm { link-up | link-down } <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ethpm	Set level for ethpm syslog messages
link-up	Configure logging level for link up syslog messages
link-down	Configure logging level for link down syslog messages
level	Logging Level

Command Mode

/exec/configure

logging level evb

[no] logging level evb <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
evb	Set syslog filter level for EVB
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level evmc

[no] logging level evmc <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
evmc	Set level for evmc syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level evmed

[no] logging level evmed <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
evmed	Set level for evmed syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level evms

[no] logging level evms <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
evms	Set level for evms syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level fabric forwarding

[no] logging level fabric forwarding <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
fabric	Fabric
forwarding	Fabric Forwarding Protocol: Host Mobility Manager (HMM)
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level fabricpath switch-id

[no] logging level fabricpath switch-id <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
fabricpath	fabricpath configuration
switch-id	switch-id submodule of fabricpath
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level fc2d

[no] logging level fc2d <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
fc2d	Set level for fc2d syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level fcdomain

[no] logging level fcdomain <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
fcdomain	set level for fcdomain syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level fcns

[no] logging level fcns <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
fcns	Set syslog filter level for name server
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level fcoe_mgr

[no] logging level fcoe_mgr <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
fcoe_mgr	Set level for fcoe_mgr syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level fcs

[no] logging level fcs <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level fdmi

[no] logging level fdmi <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
fdmi	Set logging level for fdmi
i0	0:emer 1:alert 2:crit 3:errs 4:warn 5:notifi 6:info 7:debug

Command Mode

/exec/configure

logging level feature-mgr

{ logging level feature-mgr <i0> | no logging level feature-mgr [ <i0> ] }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
feature-mgr	Set feature manager syslog level
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level flogi

[no] logging level flogi <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
flogi	Configure level for flogi syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level fs-daemon

[no] logging level fs-daemon <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
fs-daemon	fs daemon syslog level
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level fspf

[no] logging level fspf <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level fsync_mgr

[no] logging level fsync_mgr <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
fsync_mgr	Frequency Synchronization Manager
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level gpixm

[no] logging level gpixm <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
gpixm	Set level for global-pixm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level hardware-telemetry

[no] logging level hardware-telemetry <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
hardware-telemetry	Set level for hardware-telemetry syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level hsrp

[no] logging level hsrp <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
hsrp	Set level for hsrp syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level icam

[no] logging level icam <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
icam	Set level for icam syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level igmp

[no] logging level [ ip ] igmp <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ip	(Optional) Configure IP features
igmp	IGMP global configuration commands
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level imp

[no] logging level imp <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
imp	Set level for imp syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level interface-vlan

[no] logging level interface-vlan <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
interface-vlan	Set level for interface vlan syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ip pim

[no] logging level ip pim <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ip	Configure IP features
pim	Set syslog filter level for PIM
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ip sla responder

[no] logging level ip sla responder <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ip
sla	Service Level Agreement (SLA)
responder	Set level for sla-responder syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ip sla sender

[no] logging level ip sla sender <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ip
sla	Service Level Agreement (SLA)
sender	Set level for sla-sender syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ip sla twamp-server

[no] logging level ip sla twamp-server <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ip
sla	Service Level Agreement (SLA)
twamp-server	Set level for sla-twamp-server syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ipconf

[no] logging level ipconf { ipv6 <i0> | <i1> }

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ipconf	Set level for ipconf syslog messages
ipv6	Set level for ipconf syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
i1	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ipfib

logging level ipfib <i0> | no logging level ipfib

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ipfib	Set level for ipfib syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ipqos

[no] logging level { ipqos | IPQOSMGR } <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ipv6 mld

[no] logging level ipv6 mld <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ipv6	Configure IPv6 features
mld	MLD global configuration commands
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ipv6 pim

[no] logging level ipv6 pim <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ipv6	Configure IPv6 features
pim	Set syslog filter level for PIM6
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level iscm

[no] logging level iscm <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
iscm	Set level for iscm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level iscm

[no] logging level iscm <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
iscm	Set level for iscm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level isis

[no] logging level isis <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
isis	Set syslog filter level for IS-IS
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level l2fm

logging level l2fm <i0> | no logging level l2fm

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
l2fm	Set level for l2fm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level l2rib

[no] logging level l2rib <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
l2rib	l2rib syslog
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level l3vm

[no] logging level l3vm <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
l3vm	Set syslog filter level for L3VM
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level lacp

[no] logging level lacp <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
lacp	Set level for lacp syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ldap

logging level ldap <i0> | no logging level ldap [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ldap	Set level for ldap syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level lem-mgr

[no] logging level lem-mgr <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level lim

[no] logging level lim <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
lim	Set level for lim syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level lisp

[no] logging level lisp <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
lisp	Set logging level for LISP
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level lldp

[no] logging level lldp <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
lldp	Set level for lldp syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level m2rib

[no] logging level m2rib <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
m2rib	Set level for m2rib syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level mfdm

logging level mfdm <i0> | no logging level mfdm

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
mfdm	Set level for mfdm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level mfwd

[no] logging level { mfwd | mcastfwd } <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
mfwd	Configures Global IP Multicast Forwarding
mcastfwd	Configures Global IP Multicast Forwarding
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level mfwdv6

[no] logging level { mfwdv6 | mcastfwdv6 } <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
mfwdv6	Configures Global IPv6 Multicast Forwarding
mcastfwdv6	Configures Global IPv6 Multicast Forwarding
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level mmode

[no] logging level mmode <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
mmode	Set level for maintenance mode syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level module

[no] logging level module <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
module	Set level for module(linecard) manager syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level monitor

[no] logging level monitor <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
monitor	Set level for ethernet span syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level mpls manager

[no] logging level mpls manager <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
mpls	Set level for MPLS syslog messages
manager	Set level for MPLS manager syslog messages
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level mpls static

[no] logging level mpls static <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
mpls	Set level for MPLS syslog messages
static	Set level for MPLS Static syslog messages
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level mpls switching

[no] logging level mpls switching <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
mpls	Set level for MPLS syslog messages
switching	Set level for mpls switching syslog messages
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level msdp

[no] logging level [ ip ] msdp <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ip	(Optional) Configure IP features
msdp	Set syslog filter level for MSDP
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level mvsh

[no] logging level mvsh <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
mvsh	Set level for mvsh syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level nat

logging level nat <i0> | no logging level nat [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
nat	Set level for NAT syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level nbm

logging level nbm <i0> | no logging level nbm

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
nbm	Set level for nbm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure /exec/configure/nbm-vrf

logging level netstack

{ logging level netstack <level> } | { no logging level netstack [ <level> ] }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
netstack	Set syslog filter level for Netstack
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level nfm

[no] logging level nfm <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
nfm	Set level for nfm syslog messages
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level nfm

[no] logging level nfm <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
nfm	Set level for nfm syslog messages
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ngmvpn

[no] logging level ngmvpn <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ngmvpn	Set syslog filter level for NGMVPN
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ngoam

[no] logging level ngoam <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ngoam	Set level for oam logging messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level npv

[no] logging level npv <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
npv	Set level for NPV syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ntp

[no] logging level ntp <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ntp	Set syslog filter level for NTP
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level nve

[no] logging level nve <inp>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
nve	Display NVE information
inp	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level nxsdk

[no] logging level nxsdk <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
nxsdk	NXOS SDK
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ofm

logging level ofm <i0> | no logging level ofm [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ofm	Set level for ofm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level openflow

[no] logging level openflow <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
openflow	Set level for OpenFlow agent syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level orib

[no] logging level orib <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
orib	Set syslog filter level for ORIB
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ospf

[no] logging level ospf <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ospf	Set syslog filter level for OSPF
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ospfv3

[no] logging level ospfv3 <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ospfv3	Set syslog filter level for OSPFv3
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level pfstat

logging level pfstat <i0> | no logging level pfstat

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
pfstat	Set level for pfstat syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level pie

[no] logging level pie <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
pie	Set level for pie syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level pixm

[no] logging level pixm <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
pixm	Set level for vdc-local-pixm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level pktmgr

[no] logging level pktmgr <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
pktmgr	Set syslog filter level for Packet manager
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level platform

[no] logging level platform <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
platform	platform manager syslog level
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level plcmgr

[no] logging level { plcmgr | ipplc } <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level pltfm_config

[no] logging level pltfm_config <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
pltfm_config	Set level for pltfm_config syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level plugin

{ logging level plugin <i0> | no logging level plugin [ <i0> ] }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
plugin	Set level for plugin syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level poed

[no] logging level poed <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
poed	Show PoE Daemon Logging Configuration
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level port-profile

logging level port-profile <i0> | no logging level port-profile [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
port-profile	Set level for port-profile syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level port-resources

[no] logging level port-resources <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
port-resources	Set level for prm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level port-security

logging level port-security <i0> | no logging level port-security [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
port-security	Set level for port-security syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level port

[no] logging level port <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
port	Set level for port syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level port link-failure

[no] logging level port link-failure <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
port	Set level for port syslog messages
link-failure	Configure logging level for link failure syslog messages
level	Logging Level

Command Mode

/exec/configure

logging level private-vlan

[no] logging level private-vlan <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
private-vlan	Set level for private VLAN syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ptp

[no] logging level ptp <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ptp	Set level for ptp syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level radius

logging level radius <i0> | no logging level radius [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
radius	RADIUS syslog level
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level rdl

[no] logging level rdl <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
rdl	Set logging level for RDL
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level res_mgr

[no] logging level res_mgr <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
res_mgr	Set level for res_mgr syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level rib

[no] logging level rib <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
rib	Set level for rib
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level rip

[no] logging level rip <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
rip	Set syslog filter level for RIP
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level rpm

[no] logging level rpm <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
rpm	Set syslog filter level for RPM
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level rscn

{ logging level rscn <i0> | no logging level rscn [ <i1> ] }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
i1	(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level sal

[no] logging level sal <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
sal	Set level for sal syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level scheduler

[no] logging level scheduler <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
scheduler	Set logging level for scheduler
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level scsi-target

[no] logging level scsi-target <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
scsi-target	scsi target daemon syslog level
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level segment-routing

[no] logging level segment-routing <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
segment-routing	Set level for SR syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level session-mgr

logging level session-mgr <i0> | no logging level session-mgr [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
session-mgr	Set level for session-manager syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level sflow

[no] logging level sflow <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
sflow	Set level for sFlow syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level smm

[no] logging level smm <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
smm	Set logging level for Shared Memory Manager
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level snmpd

[no] logging level snmpd <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
snmpd	Set level for SNMP syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level snmpmib_proc

[no] logging level snmpmib_proc <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
snmpmib_proc	Set level for snmpmib_proc syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level spanning

[no] logging level { spanning-tree } <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
spanning-tree	Set level for stp syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level spm

[no] logging level spm <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
spm	Set level for spm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level stripcl

[no] logging level stripcl <log-level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
stripcl	Set level for stripcl syslog messages
log-level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level syncc

[no] logging level syncc <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
syncc	Set level for syncc syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level sysmgr

{ logging level sysmgr <i0> | no logging level sysmgr [ <i0> ] }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level tacacs

logging level tacacs <i0> | no logging level tacacs [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
tacacs	TACACS+ syslog level
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level telemetry

[no] logging level telemetry <level>

Syntax Description


no	(Optional) Negate a command or set its default
logging	Modify message logging facilities
level	Facility parameter for syslog messages
telemetry	Set syslog filter level for telemetry
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level template_manager

[no] logging level template_manager <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
template_manager	Set level for template manager syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level track

[no] logging level track <i0>

Syntax Description


logging	Modify message logging facilities
level	Facility parameter for syslog messages
track	Set level for track syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level tunnel-encryption

[no] logging level tunnel-encryption <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
tunnel-encryption	Set level for tunnel encryption manager syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level tunnel

logging level tunnel <i0> | no logging level tunnel [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
tunnel	Set level for tunnel syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level u2rib

[no] logging level u2rib <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
u2rib	Set level for u2rib syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level u6rib

[no] logging level u6rib <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
u6rib	Set syslog filter level for U6RIB
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level udld

[no] logging level udld <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
udld	Set level for udld syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level ufdm

[no] logging level ufdm <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ufdm	Set level for ufdm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level urib

[no] logging level urib <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
urib	Set syslog filter level for URIB
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level vdc_mgr

[no] logging level vdc_mgr <i0>

Syntax Description


logging	Modify message logging facilities
level	Facility parameter for syslog messages
vdc_mgr	Set level for vdc_mgr syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level virtual-service

[no] logging level virtual-service <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
virtual-service	Set level for virtual service syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level vlan_mgr

logging level vlan_mgr <i0> | no logging level vlan_mgr [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
vlan_mgr	Set level for VLAN syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level vmm

[no] logging level vmm <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
vmm	Set level for vmm syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level vmtracker

[no] logging level vmtracker <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
vmtracker	Set level for vmtracker syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level vpc

[no] logging level vpc <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
vpc	Set level for vPC syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level vrrp

[no] logging level { vrrp-cfg <cfg_level_num> | vrrp-eng <eng_level_num> }

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
vrrp-cfg	Set level for vrrp configuration
cfg_level_num	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
vrrp-eng	Set level for vrrp engine
eng_level_num	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level vrrpv3

[no] logging level { vrrpv3 <level> }

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
vrrpv3	Set level for vrrpv3 configuration
level	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level vsan

{ logging level vsan <i0> | no logging level vsan [ <i1> ] }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
i1	(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level vshd

[no] logging level vshd <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level vtp

[no] logging level vtp <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
vtp	Set level for vtp syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level wwnm

[no] logging level wwnm <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
wwnm	Set WWN Manager syslog level
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level xbar

[no] logging level xbar <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
xbar	xbar syslog level
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging level zone

logging level zone <i0> | no logging level zone

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging logfile

{ logging logfile <s0> <i0> [ size <i1> ] [ persistent threshold <i2> ] | no logging logfile [ <s0> <i0> [ size <i1> ] [ persistent threshold <i2> ] ] }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
logfile	Set File logging
s0	Enter the logfile name
i0	0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
size	(Optional) Set logfile size
i1	(Optional) Enter the logfile size in bytes
persistent	(Optional) Modify persistent logging
threshold	(Optional) Set persistent logging utilization alert threshold in percentage
i2	(Optional) Enter utilization alert threshold value in percentage

Command Mode

/exec/configure

logging message interface type ethernet

logging message interface type ethernet <info> | no logging message interface type ethernet <info>

Syntax Description


no	Negate a command or set its defaults
logging	Configure logging for interface
message	Interface events
interface	Interface level events
type	Interface type
ethernet	Ethernet interfaces
info	Field Names to be added to interface syslog

Command Mode

/exec/configure

logging module

[no] logging module [ <i0> ]

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
module	Set module(linecard) logging
i0	(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging monitor

[no] logging monitor [ <i0> ]

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
monitor	Set terminal line(monitor) logging level
i0	(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

/exec/configure

logging origin-id

[no] logging origin-id { hostname | ip <ip0> | string <s0> }

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
origin-id	Enable origin information for Remote Syslog Server
hostname	Use hostname as origin-id of logging messages
ip	Use ip address as origin-id of logging messages
ip0	Hostname/IPv4/IPv6 address
string	Use text string as origin-id of logging messages
s0	Enter string to append to the front of syslog msgs

Command Mode

/exec/configure

logging rate-limit

[no] logging rate-limit

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
rate-limit	Enables rate limit for log messages

Command Mode

/exec/configure

logging rfc-strict 5424

[no] logging rfc-strict { 5424 }

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
rfc-strict	Set RFC to which messages should compliant
5424	Syslogs will be compliant to RFC 5424

Usage Guidelines

Note

This command is disabled by default.

Command Mode

/exec/configure

logging server

[no] logging server <host0> [ [ <i1> ] [ port <port> ] [ secure [ trustpoint client-identity <trustpoint-label> ] ] [ use-vrf { <vrf-name> | <vrf-known-name> } | facility { auth | authpriv | cron | daemon | ftp | kernel | local0 | local1 | local2 | local3 | local4 | local5 | local6 | local7 | lpr | mail | news | syslog | user | uucp } ] + ]

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
server	Enable forwarding to Remote Syslog Server
host0	Hostname/IPv4/IPv6 address of the Remote Syslog Server
i1	(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug
port	(Optional) Destination Port when forwarding to remote server
port	(Optional) Range from 1 - 65535(Default 514)
secure	(Optional) Enable secure connection to remote server
trustpoint	(Optional) Trustpoint configuration
client-identity	(Optional) Client Identity certificate for mutual authentication
trustpoint-label	(Optional) trustpoint to use for client certificate authentication
use-vrf	(Optional) Display per-VRF information
vrf-name	(Optional) VRF name
vrf-known-name	(Optional) Known VRF name
facility	(Optional) Facility to use when forwarding to server
auth	(Optional) Use auth facility
authpriv	(Optional) Use authpriv facility
cron	(Optional) Use Cron/at facility
daemon	(Optional) Use daemon facility
ftp	(Optional) Use file transfer system facility
kernel	(Optional) Use kernel facility
local0	(Optional) Use local0 facility
local1	(Optional) Use local1 facility
local2	(Optional) Use local2 facility
local3	(Optional) Use local3 facility
local4	(Optional) Use local4 facility
local5	(Optional) Use local5 facility
local6	(Optional) Use local6 facility
local7	(Optional) Use local7 facility
lpr	(Optional) Use lpr facility
mail	(Optional) Use mail facility
news	(Optional) Use USENET news facility
syslog	(Optional) Use syslog facility
user	(Optional) Use user facility
uucp	(Optional) Use Unix-to-Unix copy system facility

Command Mode

/exec/configure

logging server dns-refresh-interval

[no] logging server dns-refresh-interval <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
server	Enable forwarding to Remote Syslog Server
dns-refresh-interval	DNS refresh interval for remote syslog server hostnames
i0	Configure DNS Refresh interval from 10 minutes to 24 hours Default:60 (will cancel any existing timers)

Command Mode

/exec/configure

logging source-interface

{ logging source-interface <interface> | no logging source-interface }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
source-interface	Enable Source-Interface for Remote Syslog Server
interface	Source interface name

Command Mode

/exec/configure

logging timestamp

[no] logging timestamp { microseconds | milliseconds | seconds }

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
timestamp	Set logging timestamp granularity
microseconds	Timestamp in micro-seconds
milliseconds	Timestamp in milli-seconds
seconds	Timestamp in seconds (Default)

Command Mode

/exec/configure

login on-failure log

[no] login on-failure log

Syntax Description


no	(Optional) Negate a command or set its defaults
login	login
on-failure	Set options for failed login attempt
log	Generate syslogs on failure logins

Command Mode

/exec/configure

login on-success log

[no] login on-success log

Syntax Description


no	(Optional) Negate a command or set its defaults
login	login
on-success	Set options for successful login attempt
log	Generate syslogs on successful logins

Command Mode

/exec/configure

logout-warning

{ logout-warning <i0> | no logout-warning [ <i0> ] }

Syntax Description


no	Negate a command or set its defaults
logout-warning	Configure logout warning
i0	Enter logout warning time in seconds

Command Mode

/exec/configure/line

low-memory exempt

[ no | default ] low-memory exempt

Syntax Description


no	(Optional) Negate a command or set its defaults
default	(Optional) Inherit values from a peer template
low-memory	Behaviour
exempt	Do

Command Mode

/exec/configure/router-bgp/router-bgp-neighbor-sess

lshow

Syntax Description


lshow	display this instance of credential

Command Mode

/exec/configure/dot1x-cred

lsp-gen-interval

lsp-gen-interval <level> <max-wait> [ <initial-wait> <second-wait> ] | no lsp-gen-interval <level> <max-wait> [ <initial-wait> <second-wait> ]

Syntax Description


no	Negate a command or set its defaults
lsp-gen-interval	Configure LSP generation interval
level	IS-IS level
max-wait	Maximum wait between trigger and LSP generation (milli-secs)
initial-wait	(Optional) Initial wait between trigger and LSP generation (milli-secs)
second-wait	(Optional) Second wait used in LSP generation (milli-secs) during backoff

Command Mode

/exec/configure/router-isis/router-isis-vrf-common

lsp-gen-interval

lsp-gen-interval <max-wait> [ <initial-wait> <second-wait> ] | no lsp-gen-interval <max-wait> [ <initial-wait> <second-wait> ]

Syntax Description


no	Negate a command or set its defaults
lsp-gen-interval	Configure LSP generation interval
max-wait	Maximum wait between trigger and LSP generation (milli-secs)
initial-wait	(Optional) Initial wait between trigger and LSP generation (milli-secs)
second-wait	(Optional) Second wait used in LSP generation (milli-secs) during backoff

Command Mode

/exec/configure/otv-isis/otv-isis-vrf-common

lsp-gen-interval

lsp-gen-interval <max-wait> [ <initial-wait> <second-wait> ] | no lsp-gen-interval <max-wait> [ <initial-wait> <second-wait> ]

Syntax Description


no	Negate a command or set its defaults
lsp-gen-interval	Configure LSP generation interval
max-wait	Maximum wait between trigger and LSP generation (milli-secs)
initial-wait	(Optional) Initial wait between trigger and LSP generation (milli-secs)
second-wait	(Optional) Second wait used in LSP generation (milli-secs) during backoff

Command Mode

/exec/configure/l2mp-isis/l2mp-isis-vrf-common

lsp-mtu

lsp-mtu <mtu> | no lsp-mtu [ <mtu> ]

Syntax Description


no	Negate a command or set its defaults
lsp-mtu	Set LSP MTU
mtu	Maximum LSP size in bytes

Command Mode

/exec/configure/l2mp-isis/l2mp-isis-vrf-common

lsp-mtu

lsp-mtu <mtu> | no lsp-mtu [ <mtu> ]

Syntax Description


no	Negate a command or set its defaults
lsp-mtu	Set LSP MTU
mtu	Maximum LSP size in bytes

Command Mode

/exec/configure/router-isis/router-isis-vrf-common

lsp-mtu

lsp-mtu <mtu> | no lsp-mtu [ <mtu> ]

Syntax Description


no	Negate a command or set its defaults
lsp-mtu	Set LSP MTU
mtu	Maximum LSP size in bytes

Command Mode

/exec/configure/otv-isis/otv-isis-vrf-common

lsp

[no] lsp <lsp-name>

Syntax Description


no	(Optional) Negate a command or set its defaults
lsp	Configure the name for the label-switched path
lsp-name	Name for this LSP

Command Mode

/exec/configure/mpls_static/ipv6

lsp

[no] lsp <lsp-name>

Syntax Description


no	(Optional) Negate a command or set its defaults
lsp	Configure the name for the label-switched path
lsp-name	Name for this LSP

Command Mode

/exec/configure/mpls_static/ipv4

Bias-Free Language

Results

Chapter: L Commands

L Commands

l2rib dup-host-mac-detection

l2rib dup-host-mac-recovery

label-allocation-mode per-vrf

label allocate global

lacp graceful-convergence

lacp max-bundle

lacp min-links

lacp mode delay

lacp mode delay

lacp port-number front-panel

lacp port-priority

lacp rate

lacp rate

lacp suspend-individual

lacp system-mac

lacp system-priority

lacp vpc-convergence

last

latency

latency

latency quantization

latency quantization

layer-2 multicast lookup mac

layer2-switched flow monitor input

layer3 peer-router

layer3 peer-router syslog

lcnd push_to_klm address port vlan

ldap-search-map

ldap-search-map

ldap-server deadtime

ldap-server host

ldap-server host test rootDN

ldap-server timeout

ldap search-map

less

license smart clear eventlog

license smart custom_id

license smart factory reset

license smart import

license smart privacy

license smart proxy address

license smart save

license smart sync local

license smart transport

license smart trust idtoken local

license smart url smart

license smart usage interval

limit-resource module-type

limit-resource monitor-session-erspan-dst minimum maximum equal-to-min

limit-resource monitor-session-inband-src minimum maximum equal-to-min

limit-resource monitor-session minimum maximum equal-to-min

limit-resource port-channel minimum maximum

limit-resource vlan minimum maximum equal-to-min

limit-resource vrf minimum maximum equal-to-min

limit address-count

line console

line console

line vty

link-level-flow-control watch-dog-interval on

link-state-trap

link debounce

link dfe adaptive-tuning

link loopback

link mac-up timer

link transmit reset-skip

lisp

lisp ddt

lisp ddt authoritative-prefix eid-prefix

lisp ddt delegate eid-prefix

lisp ddt map-server-peer eid-prefix

lisp ddt root

lisp dynamic-eid

lisp dynamic-eid

lisp explicit-locator-path

lisp explicit-locator-path