The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
{ packet-size <packetsize> }
Syntax Description
|
packet-size |
Packet |
|
packetsize |
Size |
Command Mode
/exec/configure/configngoamconnectcheck
[no] param-list <plistname> [ cross-check ] | param-list <plistname>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
param-list |
Configure a parameter list |
|
plistname |
Enter the name of the parameter list |
|
cross-check |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
Command Mode
/exec/configure
[no] parity <parity-value>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
parity |
Set terminal parity |
|
parity-value |
terminal parity value |
Command Mode
/exec/configure/console
[no] parity { even | none | odd }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
parity |
Set terminal parity |
|
even |
Even parity |
|
none |
No parity |
|
odd |
Odd parity |
Command Mode
/exec/configure/com1
[no] passive-interface default
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
passive-interface |
Suppress routing updates on the interface |
|
default |
interfaces passive by default |
Command Mode
/exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
[no] passive-interface default <level>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
passive-interface |
Suppress IS-IS PDU |
|
default |
Undo a command |
|
level |
IS-IS level |
Command Mode
/exec/configure/router-isis/router-isis-vrf-common
[no] passive-interface default
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
passive-interface |
Suppress routing updates on the interface |
|
default |
interfaces passive by default |
Command Mode
/exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
[no] passive-interface default
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
passive-interface |
Suppress routing updates on the interface |
|
default |
interfaces passive by default |
Command Mode
/exec/configure/router-ospf /exec/configure/router-ospf/vrf
{ [ no ] password <passwd> }
Syntax Description
|
password |
password |
|
passwd |
password |
Command Mode
/exec/configure/dot1x-cred
password [ vrf { <vrf-name> | <vrf-known-name> } ] { required [ req-for <req-pfx-list> ] | { fallback | option <seq-num> opt-for <opt-pfx-list> } { key-chain <name> } } | no password [ vrf { <vrf-name> | <vrf-known-name> } ] { required | fallback | option <seq-num> }
Syntax Description
|
no |
Negate a command or set its defaults |
|
password |
Configure LDP password |
|
vrf |
(Optional) VRF Routing/Forwarding instance information |
|
vrf-name |
(Optional) VPN Routing/Forwarding instance name |
|
vrf-known-name |
(Optional) Known VRF name |
|
required |
Password is required for the peer |
|
req-for |
(Optional) Prefix list specifying control on LDP peers |
|
req-pfx-list |
(Optional) Prefix list for LDP peers |
|
fallback |
Specifies a fallback password will follow |
|
option |
LDP password option |
|
seq-num |
Sequence number of the LDP password option |
|
opt-for |
Prefix list specifying control on LDP peers |
|
opt-pfx-list |
Prefix list for LDP peers |
|
key-chain |
Specifies a key-chain name will follow |
|
name |
Key-chain name |
Command Mode
/exec/configure/ldp
password <password-string> | { no | default } password [ <password-string> ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
default |
Inherit values from a peer template |
|
password |
Configure a password for neighbor |
|
password-string |
Neighbor password |
Command Mode
/exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-neighbor-stmp /exec/configure/router-bgp/router-bgp-vrf-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor /exec/configure/router-bgp/router-bgp-vrf-prefixneighbor
[no] password prompt username
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
password |
Password for the user |
|
prompt |
Enable prompt for password |
|
username |
Enable prompt for password on username command |
Command Mode
/exec/configure
[no] password secure-mode
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
password |
Password for the user |
|
secure-mode |
Enable secure mode for changing password |
Command Mode
/exec/configure
[no] password strength-check
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
password |
Password for the user |
|
strength-check |
Strength check of password |
Command Mode
/exec/configure
[ no | default ] path-attribute { discard | treat-as-withdraw } { <ptype> | range <start> <end> } in
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
default |
(Optional) Inherit values from a peer template |
|
path-attribute |
BGP path attribute optional filtering |
|
discard |
Discard matching path-attribute from this neighbor |
|
treat-as-withdraw |
Withdraw routes for matching path-attribute from this neighbor. This has higher priority than discard |
|
range |
path attribute range |
|
in |
Perform path attribute filtering on inbound updates |
|
ptype |
path attribute type |
|
start |
path attribute range start value |
|
end |
path attribute range end value |
Command Mode
/exec/configure/router-bgp/router-bgp-neighbor-sess
path { <dn> | environment |
Syntax Description
|
| |
vxlan |
|
| |
vxlan |
|
path |
Create a sensor path |
|
dn |
Distinguished Name |
|
environment |
Monitor chassis information including fan,temperature,power,storage,supervisor,linecard |
Command Mode
/exec/configure/telemetry/sensor-group
{ no path <path-num> | path <path-num> next-hop <next-hop> out-label-stack { <static-outlabel> + | implicit-null } }
Syntax Description
|
no |
Negate a command or set its defaults |
|
path |
Configure an outgoing path for the LSP |
|
path-num |
Path identifier |
|
next-hop |
Nexthop |
|
next-hop |
Destination IPv4 next hop |
|
out-label-stack |
Series of output labels |
|
static-outlabel |
Label Value |
|
implicit-null |
IETF MPLS implicit null label (3) |
Command Mode
/exec/configure/mpls_static/ipv4/lsp/inlabel/forw
pathtrace { domain <i0> vsan <i1> [ reverse ] [ detail ] | fcid <fcid> vsan1 <i2> [ reverse1 ] [ detail1 ] }
Syntax Description
|
pathtrace |
Trace the route statistics. |
|
domain |
Destination domain. |
|
i0 |
Enter the destination domain ID |
|
vsan |
VSAN id |
|
i1 |
The VSAN Number. |
|
reverse |
(Optional) Trace reverse path |
|
detail |
(Optional) Detailed statistics |
|
fcid |
FC-id of the destination N-Port |
|
fcid |
The FC-id |
|
vsan1 |
vsan id of the destination N Port. |
|
i2 |
The VSAN Number. |
|
reverse1 |
(Optional) Trace reverse path |
|
detail1 |
(Optional) Detailed statistics |
Command Mode
/exec
pathtrace { { nve [ mac <dmac> <dot1qid> [ <intfid> ] ] | srv6 } { [ ip ] [ <ipv6_addr> | <ipv4_host> | unknown ] [ vrf { <vrf-name> | <vrf-known-name> } ] [ profile <pid> ] [ payload { [ mac-addr <dstmac> <smac> ] [ dot1q <dot1q-id> ] [ ip <dstip> <srcip> | ipv6 <dstipv6> <srcipv6> ] [ port <sport> <dport> ] [ proto <proto-id> ] [ src-intf <src_if> ] } payload-end ] } [ { [ sid <sid_addr> ] [ via { <sid_list_entry> } + sid-list-end ] [ end-otp <otp> ] [ end-op <op> ] [ no-reduced-srh ] } ] [ [ { vni <vni-id> } ] [ { sport <sval> } ] ] [ source { <src_if_ip_addr> | <src_if_ipv6_addr> } |
Syntax Description
|
pathtrace |
Test |
|
nve |
Vxlan oam commands |
|
ip |
(Optional) ip address |
|
mac |
(Optional) MAC address |
|
dmac |
(Optional) Destination mac address |
|
dot1qid |
(Optional) Encapsulation dot1q/bd on which the mac is learnt |
|
intfid |
(Optional) Name of the interface for ngoam traceroute on which dot1q is configured |
|
srv6 |
Use the Segment Routed fabric for this ping |
|
ipv4_host |
(Optional) Ipv4 remote host address |
|
unknown |
(Optional) Find what to ping from payload info |
|
vrf |
(Optional) Display per-VRF information |
|
vrf-name |
(Optional) VRF name |
|
vrf-known-name |
(Optional) Known VRF name |
|
profile |
(Optional) NGOAM profile to use |
|
pid |
(Optional) NGOAM profile id |
|
payload |
(Optional) Enter customer payload |
|
mac-addr |
(Optional) Mac |
|
dstmac |
(Optional) Destination mac address |
|
smac |
(Optional) Source mac address |
|
dot1q |
(Optional) Encapsulation dot1q/bd |
|
dot1q-id |
(Optional) Encapsulation dot1q/bd on which the mac is learnt |
|
dstip |
(Optional) Destination ipv4 address |
|
srcip |
(Optional) source ipv4 address |
|
ipv6 |
(Optional) ipv6 address |
|
port |
(Optional) L4 port info |
|
sport |
(Optional) Source port |
|
dport |
(Optional) Destination port |
|
proto |
(Optional) Protocol |
|
proto-id |
(Optional) IANA Protocol id |
|
src-intf |
(Optional) Interface on which the host with src ip of the payload is connected |
|
src_if |
(Optional) Interface |
|
payload-end |
(Optional) End of payload info |
|
sid |
(Optional) Segment Identifier |
|
via |
(Optional) Specify the SID list for the packet to traverse through |
|
sid-list-end |
(Optional) Indicate end of sid list |
|
end-otp |
(Optional) Override default End.OTP SID |
|
end-op |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
no-reduced-srh |
(Optional) For srv6 pathtrace pkts, do not use a Reduced SRH |
|
vni |
(Optional) Vni for vxlan |
|
vni-id |
(Optional) Configure vni id |
|
sport |
(Optional) Outer UDP source port for vxlan |
|
sval |
(Optional) Udp source port range, max span 1024, Example: 2000-3000,400,500 |
|
source |
(Optional) Source IP address to use |
|
src_if_ip_addr |
(Optional) IP address of local system |
Command Mode
/exec
[no] pause { buffer-size <size-in-bytes> pause-threshold <xoff-bytes> resume-threshold <xon-bytes> }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pause |
PAUSE characteristics (CBFC) |
|
buffer-size |
Ingress buffer size in bytes |
|
pause-threshold |
Buffer limit for pausing in bytes |
|
resume-threshold |
Buffer limit at which to resume in bytes |
Command Mode
/exec/configure/policy-map/type/queuing/class
[no] pause buffer-size2 <size-in-bytes> pause-threshold2 <xoff-bytes> resume-threshold2 <xon-bytes>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pause |
PAUSE characteristics (CBFC) |
|
buffer-size2 |
Ingress buffer size in bytes |
|
pause-threshold2 |
Buffer limit for pausing in bytes |
|
resume-threshold2 |
Buffer limit at which to resume in bytes |
Command Mode
/exec/configure/policy-map/type/queuing/class
[no] pause { priority-group <priority-group-number> }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pause |
PAUSE characteristics (CBFC) |
|
priority-group |
ingress priority-group to which the traffic is mapped and pause limits are applied |
|
priority-group-number |
Priority group value |
Command Mode
/exec/configure/policy-map/type/queuing/class
[no] payload
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
payload |
Configure ngoam connectivity check payload |
Command Mode
/exec/configure/configngoamconnectcheck
[no] pcc
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pcc |
PCC related configuration |
Command Mode
/exec/configure/sr/te
[no] pce-address ipv4 <ip-address> [ precedence <precedence> ]
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pce-address |
Configure the address of the PCE |
|
ipv4 |
Configure v4 address of the PCE |
|
precedence |
(Optional) Precedence of the PCE |
|
ip-address |
PCE address |
|
precedence |
(Optional) Path-option preference |
Command Mode
/exec/configure/sr/te/pcc
[no] pcep
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pcep |
Dynamic path needs to be computed externally via PCEP |
Command Mode
/exec/configure/sr/te/color/cndpaths/pref/dyn
[no] pcep
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pcep |
Dynamic path needs to be computed externally via PCEP |
Command Mode
/exec/configure/sr/te/pol/cndpaths/pref/dyn
[no] pdop threshold <thres>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pdop |
PDOP threshold configuration |
|
threshold |
PDOP threshold configuration |
|
thres |
PDOP threshold value |
Command Mode
/exec/configure/gnss-if
peer-gateway [ exclude-vlan <vlan-list> ] | no peer-gateway
Syntax Description
|
no |
Negate a command or set its defaults |
|
peer-gateway |
Enable L3 forwarding for packets destined to peer's gateway mac-address |
|
exclude-vlan |
(Optional) Specify VLANs to be excluded from peer-gateway functionality |
|
vlan-list |
(Optional) Specify the list of vlans |
Command Mode
/exec/configure/vpc-domain
[no] peer-ip { <addr> }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
peer-ip |
Static IP Address Configuration |
|
addr |
Remote Peer IP Address |
Command Mode
/exec/configure/if-nve/vni/ingr-rep
peer-keepalive destination { <dst-ip> | <dst-ipv6> } [ [ source [ <src-ip> | <src-ipv6> ] | udp-port <udp-port-num> | vrf { <vrf-name> | <vrf-known-name> } | { interval <interval-ms> timeout <time-out> } | tos-byte <tos-byte-value> | hold-timeout <hold-time-out> ] + | [ source [ <src-ip> | <src-ipv6> ] | udp-port <udp-port-num> | vrf { <vrf-name> | <vrf-known-name> } | { interval <interval-ms> timeout <time-out> } | tos { <tos-value> | min-delay | max-throughput | max-reliability | min-monetary-cost | normal } | hold-timeout <hold-time-out> ] + | [ source [ <src-ip> | <src-ipv6> ] | udp-port <udp-port-num> | vrf { <vrf-name> | <vrf-known-name> } | { interval <interval-ms> timeout <time-out> } | precedence { <prec-vlaue> | network | internet | critical | flash-override | flash | immediate | priority | routine } | hold-timeout <hold-time-out> ] + ]
Syntax Description
|
peer-keepalive |
Keepalive/Hello with peer switch |
|
destination |
specify destination ip address of peer switch |
|
dst-ip |
IPv4 address (A.B.C.D) of destination |
|
source |
(Optional) source interface for hello |
|
src-ip |
(Optional) IPv4 address (A.B.C.D) of source |
|
udp-port |
(Optional) enter UDP port number used for hello |
|
udp-port-num |
(Optional) udp port number for hellos |
|
vrf |
(Optional) vrf to be used for hello messages |
|
vrf-name |
(Optional) vrf to be used for hellos |
|
vrf-known-name |
(Optional) Known VRF name |
|
interval |
(Optional) enter interval in milleseconds |
|
interval-ms |
(Optional) Enter interval in milleseconds |
|
timeout |
(Optional) enter timeout in seconds |
|
time-out |
(Optional) enter timeout in seconds |
|
precedence |
(Optional) Precedence |
|
prec-vlaue |
(Optional) Precedence value |
|
network |
(Optional) network (7) |
|
internet |
(Optional) internet (6) |
|
critical |
(Optional) critical (5) |
|
flash-override |
(Optional) flash-override (4) |
|
flash |
(Optional) flash (3) |
|
immediate |
(Optional) immediate (2) |
|
priority |
(Optional) priority (1) |
|
routine |
(Optional) routine (0) |
|
tos |
(Optional) Type of Service(IPV4)/Traffic Class(IPV6) |
|
tos-value |
(Optional) Enter 4-bit TOS value |
|
min-delay |
(Optional) min-delay (8) |
|
max-throughput |
(Optional) max-throughput (4) |
|
max-reliability |
(Optional) max-reliability (2) |
|
min-monetary-cost |
(Optional) min-monetary-cost (1) |
|
normal |
(Optional) normal (0) |
|
tos-byte |
(Optional) Type of Service Byte (IPv4)/Traffic Class Octet(IPv6) |
|
tos-byte-value |
(Optional) Enter 8-bit TOS value |
|
hold-timeout |
(Optional) hold timeout to ignore stale peer alive messages |
|
hold-time-out |
(Optional) Enter hold-timeout in seconds |
Command Mode
/exec/configure/vpc-domain
[no] peer-switch
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
peer-switch |
Enable peer switch on vPC pair switches |
Command Mode
/exec/configure/vpc-domain
peer-type { fabric-external | fabric-border-leaf } | { no | default } peer-type
Syntax Description
|
no |
Negate a command or set its defaults |
|
default |
Inherit values from a peer template |
|
peer-type |
Neighbor facing |
|
fabric-external |
Fabric external |
|
fabric-border-leaf |
Fabric Border Leaf |
Command Mode
/exec/configure/router-bgp/router-bgp-neighbor-sess
[no] peer-vtep <addr>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
peer-vtep |
Configure tunnel End Point (deprecate) |
|
addr |
Remote VTEP IP Address |
Command Mode
/exec/configure/if-nve/vni
[no] peer local service <service-name>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
peer |
Peer cli for sandwich mode failure notification |
|
local |
Peer involved in sandwich mode |
|
service |
Peer service involved in sandwich mode |
|
service-name |
Peer service name string |
Command Mode
/exec/configure/itd
[no] per-ingress-port-mtu-mode
Syntax Description
|
no |
(Optional) Negate the command |
|
per-ingress-port-mtu-mode |
per-ingress-port mtu mode |
Command Mode
/exec/configure handle auto 424
[no] periodic-inventory notification
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
periodic-inventory |
Configure periodic software inventory message dispatch |
|
notification |
Enable periodic software inventory message dispatch |
Command Mode
/exec/configure/callhome
periodic-inventory notification { interval <i0> | timeofday <s0> }
Syntax Description
|
periodic-inventory |
Configure periodic software inventory message dispatch |
|
notification |
Enable periodic software inventory message dispatch |
|
interval |
Configure the time period for periodic inventory |
|
i0 |
Time period in days (default is 7 days) |
|
timeofday |
Configure the timeofday for periodic inventory in HH:MM format |
|
s0 |
Time period in HH:MM format |
Command Mode
/exec/configure/callhome
[no] periodic-probe-interval <val>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
periodic-probe-interval |
Configure Loop Detection Probe Interval, Unit:Second |
|
val |
Loop detection probe timer value in seconds |
Command Mode
/exec/configure/configngoamloopdetection
{ [ <seqno> ] | no } periodic { Monday | Tuesday | Wednesday | Thursday | Friday | Saturday | Sunday } <stime> to { <eday> } <etime>
Syntax Description
|
seqno |
(Optional) Sequence number |
|
no |
Negate a command or set its defaults |
|
periodic |
Periodic time and date |
|
Monday |
Monday |
|
Tuesday |
Tuesday |
|
Wednesday |
Wednesday |
|
Thursday |
Thursday |
|
Friday |
Friday |
|
Saturday |
Saturday |
|
Sunday |
Sunday |
|
eday |
Day of the week |
|
stime |
Starting time |
|
to |
Ending day and time |
|
etime |
Ending time |
Command Mode
/exec/configure/timerange
{ [ <seqno> ] | no } periodic { { Monday | Tuesday | Wednesday | Thursday | Friday | Saturday | Sunday } + | daily | weekdays | weekend } <stime> to <etime>
Syntax Description
|
seqno |
(Optional) Sequence number |
|
no |
Negate a command or set its defaults |
|
periodic |
Periodic time and date |
|
Monday |
Monday |
|
Tuesday |
Tuesday |
|
Wednesday |
Wednesday |
|
Thursday |
Thursday |
|
Friday |
Friday |
|
Saturday |
Saturday |
|
Sunday |
Sunday |
|
daily |
Every day of the week |
|
weekdays |
Monday thru Friday |
|
weekend |
Saturday and Sunday |
|
stime |
Starting time |
|
to |
Ending day and time |
|
etime |
Ending time |
Command Mode
/exec/configure/timerange
[no] permit interface <if0>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
permit |
Permit access to interfaces (applicable if interface policy is 'deny') |
|
interface |
Enter the range of interfaces accessible the role |
|
if0 |
Enter the interface range |
Command Mode
/exec/configure/role/interface
[no] permit vlan <vlan-mrange>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
permit |
Permit access to vlans (applicable if vlan policy is 'deny') |
|
vlan |
Enter the range of vlans accessible the role |
|
vlan-mrange |
Enter the vlan range |
Command Mode
/exec/configure/role/vlan
[no] permit vrf <vrf-name>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
permit |
Permit access to vrf (applicable if vrf policy is 'deny') |
|
vrf |
Enter the range of vrf accessible the role |
|
vrf-name |
Enter the vrf name |
Command Mode
/exec/configure/role/vrf
[no] permit vsan <vsan-mrange>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
permit |
Permit access to vsans (applicable if vsan policy is 'deny') |
|
vsan |
Enter the range of vsans accessible the role |
|
vsan-mrange |
Enter the vsan range |
Command Mode
/exec/configure/role/vsan
<seqno> <permitdeny> <mpls> { <label1_any> | { <label1> [ mask <label1_mask> ] } } [ <label2_any> | { <label2> [ mask <label2_mask> ] } ] [ <label3_any> | { <label3> [ mask <label3_mask> ] } ] [ <label4_any> | { <label4> [ mask <label4_mask> ] } ] { <mplsaction> <mplsactionid> } + [ load-share ]
Syntax Description
|
seqno |
Sequence number |
|
permitdeny |
Permit/deny |
|
mask |
(Optional) mask |
|
label1 |
mpls label one |
|
label2 |
(Optional) mpls label two |
|
label3 |
(Optional) mpls label three |
|
label4 |
(Optional) mpls label four |
|
label1_mask |
(Optional) mpls label one mask |
|
label2_mask |
(Optional) mpls label two mask |
|
label3_mask |
(Optional) mpls label three mask |
|
label4_mask |
(Optional) mpls label four mask |
|
label1_any |
label one Any |
|
label2_any |
(Optional) label two Any |
|
label3_any |
(Optional) label three Any |
|
label4_any |
(Optional) label four Any |
|
mpls |
mpls keyword |
|
mplsaction |
mpls ACL Action |
|
mplsactionid |
redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63> set-erspan-gre-proto: <1-65535> redirect_all: Ethernet1/1,port-channel1 |
|
load-share |
(Optional) load share amoung the ports specified in redirect list |
Command Mode
/exec/configure/mplsacl
{ persist-disk <disksize-units> | no persist-disk [ <disksize-units> ] }
Syntax Description
|
no |
Negate a command or set its defaults |
|
persist-disk |
IOX Application persistent data disk reservation MB units |
|
disksize-units |
IOX Application persistent disk size in MB |
Command Mode
/exec/configure/app-hosting-resource-profile-custom
[no] personality
Syntax Description
|
no |
(Optional) Negate a mode |
|
personality |
Config Personality |
Command Mode
/exec/configure
personality backup { <uri_local> | <uri_remote> [ password <password> ] [ vrf <vrf-known-name> ] }
Syntax Description
|
personality |
personality |
|
backup |
backup personality |
|
password |
(Optional) The password for personality backups |
|
vrf |
(Optional) The VRF for personality backups |
|
uri_local |
Personality backup local destination |
|
uri_remote |
Personality backup remote destination |
|
password |
(Optional) Password for SCP username |
|
vrf-known-name |
(Optional) VRF name |
Command Mode
/exec
personality restore <uri> [ user-name <user> ] [ password <password> ] [ hostname <hostname> ] [ vrf <vrf_name> ]
Syntax Description
|
personality |
Personality |
|
restore |
Restore the personality file |
|
uri |
Personality file |
|
user-name |
(Optional) The username for downloads |
|
user |
(Optional) The username |
|
password |
(Optional) The password for downloads |
|
password |
(Optional) The password |
|
hostname |
(Optional) The hostname for downloads |
|
hostname |
(Optional) The hostname |
|
vrf |
(Optional) The VRF for downloads |
|
vrf_name |
(Optional) The VRF name |
Command Mode
/exec
{ phone-contact <s0> | no phone-contact }
Syntax Description
|
no |
Negate a command or set its defaults |
|
phone-contact |
Contact person's phone number |
|
s0 |
Phone number in international format(such as +1-800-123-4567) |
Command Mode
/exec/configure/callhome
[no] pim
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pim |
Policies for a Remote Receiver |
Command Mode
/exec/configure/nbm-host-policy
[no] pim
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pim |
Policies for a Remote Receiver |
Command Mode
/exec/configure/nbm-vrf/nbm-host-policy
ping { { nve [ mac <dmac> <dot1qid> [ <intfid> ] ] | srv6 } { [ ip ] [ <ipv6_addr> | <ipv4_host> | unknown ] [ vrf { <vrf-name> | <vrf-known-name> } ] [ profile <pid> ] [ payload { [ mac-addr <dstmac> <smac> ] [ dot1q <dot1q-id> ] [ ip <dstip> <srcip> | ipv6 <dstipv6> <srcipv6> ] [ port <sport> <dport> ] [ proto <proto-id> ] [ src-intf <src_if> ] } payload-end ] } [ { [ sid <sid_addr> ] [ via { <sid_list_entry> } + sid-list-end ] [ end-otp <otp> ] [ end-op <op> ] [ no-proof-of-transit ] [ no-reduced-srh ] } ] [ [ { vni <vni-id> } ] [ { sport <sval> } ] ] [ source { <src_if_ip_addr> | <src_if_ipv6_addr> } |
Syntax Description
|
{ |
<count> |
|
ping |
Test |
|
nve |
Vxlan oam commands |
|
ip |
(Optional) ip address |
|
mac |
(Optional) MAC address |
|
dmac |
(Optional) Destination mac address |
|
dot1qid |
(Optional) Encapsulation dot1q/bd on which the mac is learnt |
|
intfid |
(Optional) Name of the interface for ngoam traceroute on which dot1q is configured |
|
srv6 |
Use the Segment Routed fabric for this ping |
|
ipv4_host |
(Optional) Ipv4 remote host address |
|
unknown |
(Optional) Find what to ping from payload info |
|
vrf |
(Optional) Display per-VRF information |
|
vrf-name |
(Optional) VRF name |
|
vrf-known-name |
(Optional) Known VRF name |
|
profile |
(Optional) NGOAM profile to use |
|
pid |
(Optional) NGOAM profile id |
|
payload |
(Optional) Enter customer payload |
|
mac-addr |
(Optional) Mac |
|
dstmac |
(Optional) Destination mac address |
|
smac |
(Optional) Source mac address |
|
dot1q |
(Optional) Encapsulation dot1q/bd |
|
dot1q-id |
(Optional) Encapsulation dot1q/bd on which the mac is learnt |
|
dstip |
(Optional) Destination ipv4 address |
|
srcip |
(Optional) source ipv4 address |
|
ipv6 |
(Optional) ipv6 address |
|
port |
(Optional) L4 port info |
|
sport |
(Optional) Source port |
|
dport |
(Optional) Destination port |
|
proto |
(Optional) Protocol |
|
proto-id |
(Optional) IANA Protocol id |
|
src-intf |
(Optional) Interface on which the host with src ip of the payload is connected |
|
src_if |
(Optional) Interface |
|
payload-end |
(Optional) End of payload info |
|
sid |
(Optional) Segment Identifier |
|
via |
(Optional) Specify the SID list for the packet to traverse through |
|
sid-list-end |
(Optional) Indicate end of sid list |
|
end-otp |
(Optional) Override default End.OTP SID |
|
end-op |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
vni |
(Optional) Vni for vxlan |
|
vni-id |
(Optional) Configure vni id |
|
sport |
(Optional) Outer UDP source port for vxlan |
|
sval |
(Optional) Udp source port range, max span 1024, Example: 2000-3000,400,500 |
|
source |
(Optional) Source IP address to use |
|
src_if_ip_addr |
(Optional) IP address of local system |
|
no-proof-of-transit |
(Optional) For srv6 ping pkts, disable proof of transit |
|
no-reduced-srh |
(Optional) For srv6 ping pkts, do not use a Reduced SRH |
Command Mode
/exec
ping6 { { <host> | <hostname> } | { multicast <group> } } [ [ { count { <count> | unlimited } } | { packet-size <packetsize> } | [ source { <host1> | <hostname> } ] | vrf { <vrf-name> | <vrf-known-name> } | timeout <timeout> | { interval <interval> } ] + | [ { count { <count> | unlimited } } | { packet-size <packetsize> } | { source-interface <src-intf> } | timeout <timeout> | { interval <interval> } ] + ]
Syntax Description
|
ping6 |
Test |
|
count |
(Optional) Number |
|
count |
(Optional) Number |
|
unlimited |
(Optional) unlimited |
|
packet-size |
(Optional) Packet |
|
packetsize |
(Optional) Size |
|
source-interface |
(Optional) Select source interface |
|
src-intf |
(Optional) Specify interface |
|
interval |
(Optional) Wait |
|
interval |
(Optional) Interval |
|
hostname |
Enter |
|
multicast |
Multicast |
|
vrf |
(Optional) Display per-VRF information |
|
vrf-name |
(Optional) VRF name |
|
vrf-known-name |
(Optional) Known VRF name |
|
source |
(Optional) Source |
|
timeout |
(Optional) Specify |
|
timeout |
(Optional) Timeout |
Command Mode
/exec
ping [ { { <alpha> | <numeric> [ loopback interface <interface> ] } | { multicast <group> interface <interface> [ loopback ] } } [ [ source-interface <src-intf> | vrf { <vrf-name> | <vrf-known-name> } ] [ count { <count> | unlimited } | packet-size <packetsize> | vrf { <vrf-name> | <vrf-known-name> } | interval <interval> | source { <alpha> | <numeric1> } | df-bit | timeout <timeout> ] + | [ count { <count> | unlimited } | packet-size <packetsize> | source-interface <src-intf> | interval <interval> | df-bit | timeout <timeout> ] + ] ]
Syntax Description
|
ping |
Test |
|
count |
(Optional) Number |
|
unlimited |
(Optional) Unlimited |
|
count |
(Optional) Number |
|
packet-size |
(Optional) Packet |
|
packetsize |
(Optional) Size |
|
source-interface |
(Optional) Select source interface |
|
src-intf |
(Optional) Specify interface |
|
interval |
(Optional) Wait |
|
interval |
(Optional) Interval |
|
numeric |
(Optional) IP address of remote system |
|
numeric1 |
(Optional) IP |
|
alpha |
(Optional) Enter |
|
multicast |
(Optional) Multicast |
|
group |
(Optional) Multicast |
|
interface |
(Optional) Interface |
|
interface |
(Optional) Interface |
|
loopback |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
source |
(Optional) Source |
|
df-bit |
(Optional) Enable |
|
timeout |
(Optional) Specify |
|
timeout |
(Optional) Timeout |
|
vrf |
(Optional) Display per-VRF information |
|
vrf-name |
(Optional) VRF name |
|
vrf-known-name |
(Optional) Known VRF name |
Command Mode
/exec
ping mpls { nil-fec { { labels <comma-separated-labels> } { output { ointerface <tx-interface> } nexthop <nexthop-ip-addr> } | { policy { { name <srte-policy-name> } | { endpoint <srte-policy-endpoint> color <srte-policy-color> } } [ { output { ointerface <tx-interface> } [ nexthop <nexthop-ip-addr> ] } ] } } } [ { repeat <count> } | { { size <size> } | { sweep <min-size> <max-size> <increment> } } | { timeout <seconds> } | { interval <milliseconds> } | { destination <addr-start> [ <addr-end> [ <addr-incr-mask> | <addr-incr> ] ] } | { source <addr> } | { exp <exp-value> } | { pad <pattern> } | { ttl <ttl> } | { verbose } | { reply { { mode { <reply-mode-ipv4> | router-alert | control-channel | no-reply } } | { dscp { <dscp-bits> | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | default | ef } } | { pad-tlv } } } + | { force-explicit-null } | { dsmap [ hashkey { none | { hash-ipv4 { bitmap <bitmap-size> } } } ] } | { flags { fec } } ] +
Syntax Description
|
ping |
need |
|
mpls |
Test |
|
nil-fec |
Target |
|
labels |
A |
|
comma-separated-labels |
A |
|
repeat |
(Optional) Repeat |
|
count |
(Optional) Repeat |
|
size |
(Optional) Packet |
|
size |
(Optional) Datagram |
|
sweep |
(Optional) Sweep |
|
min-size |
(Optional) |
|
max-size |
(Optional) |
|
increment |
(Optional) Sweep |
|
timeout |
(Optional) Timeout |
|
seconds |
(Optional) Timeout |
|
interval |
(Optional) Send |
|
milliseconds |
(Optional) Send |
|
destination |
(Optional) Destination |
|
addr-start |
(Optional) Destination |
|
addr-end |
(Optional) Destination |
|
addr-incr-mask |
(Optional) Destination |
|
addr-incr |
(Optional) Destination |
|
source |
(Optional) Source |
|
addr |
(Optional) Source |
|
exp |
(Optional) EXP |
|
exp-value |
(Optional) EXP |
|
pad |
(Optional) Pad |
|
pattern |
(Optional) Pad |
|
ttl |
(Optional) Time |
|
ttl |
(Optional) TTL |
|
verbose |
(Optional) verbose |
|
reply |
(Optional) Reply |
|
mode |
(Optional) Reply |
|
reply-mode-ipv4 |
(Optional) Send |
|
router-alert |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
control-channel |
(Optional) Send |
|
no-reply |
(Optional) Send |
|
dscp |
(Optional) DSCP |
|
dscp-bits |
(Optional) Differentiated |
|
af11 |
(Optional) Match |
|
af12 |
(Optional) Match |
|
af13 |
(Optional) Match |
|
af21 |
(Optional) Match |
|
af22 |
(Optional) Match |
|
af23 |
(Optional) Match |
|
af31 |
(Optional) Match |
|
af32 |
(Optional) Match |
|
af33 |
(Optional) Match |
|
af41 |
(Optional) Match |
|
af42 |
(Optional) Match |
|
af43 |
(Optional) Match |
|
cs1 |
(Optional) Match |
|
cs2 |
(Optional) Match |
|
cs3 |
(Optional) Match |
|
cs4 |
(Optional) Match |
|
cs5 |
(Optional) Match |
|
cs6 |
(Optional) Match |
|
cs7 |
(Optional) Match |
|
default |
(Optional) Match |
|
ef |
(Optional) Match |
|
pad-tlv |
(Optional) Reply |
|
force-explicit-null |
(Optional) Force |
|
output |
Output |
|
ointerface |
Echo |
|
tx-interface |
Echo |
|
nexthop |
Next |
|
nexthop-ip-addr |
Next |
|
dsmap |
(Optional) Request |
|
hashkey |
(Optional) Downstream |
|
none |
(Optional) Hash |
|
hash-ipv4 |
(Optional) IPv4 |
|
bitmap |
(Optional) Hash |
|
bitmap-size |
(Optional) Multipath |
|
flags |
(Optional) Flag |
|
fec |
(Optional) Request |
|
policy |
Derive |
|
name |
Specify |
|
color |
Specify |
|
endpoint |
Specify |
|
srte-policy-name |
The |
|
srte-policy-color |
The |
|
srte-policy-endpoint |
The |
Command Mode
/exec
ping mpls monitor session-id <id> nil-fec labels <comma-separated-labels> output ointerface <tx-interface> nexthop <nexthop-ip-addr> [ interval <interval> ] [ multiplier <multiplier> ] | no ping mpls monitor session-id <id>
Syntax Description
|
no |
Negate a command or set its defaults |
|
ping |
need |
|
mpls |
Test |
|
monitor |
Start |
|
session-id |
Id |
|
id |
Id |
|
nil-fec |
Target |
|
labels |
A |
|
comma-separated-labels |
A |
|
output |
Output |
|
ointerface |
Echo |
|
tx-interface |
Echo |
|
nexthop |
Next |
|
nexthop-ip-addr |
Next |
|
interval |
(Optional) Interval |
|
interval |
(Optional) Interval |
|
multiplier |
(Optional) Number |
|
multiplier |
(Optional) Number |
Command Mode
/exec
ping sr-mpls { <sr-ipv4-prefix> fec-type { { igp isis } | { bgp } | { generic } } } [ { repeat <count> } | { { size <size> } | { sweep <min-size> <max-size> <increment> } } | { timeout <seconds> } | { interval <milliseconds> } | { destination <addr-start> [ <addr-end> [ <addr-incr-mask> | <addr-incr> ] ] } | { source <addr> } | { exp <exp-value> } | { pad <pattern> } | { ttl <ttl> } | { verbose } | { reply { { mode { <reply-mode-ipv4> | router-alert | control-channel | no-reply } } | { dscp { <dscp-bits> | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | default | ef } } | { pad-tlv } } } + | { force-explicit-null } | { dsmap [ hashkey { none | { hash-ipv4 { bitmap <bitmap-size> } } } ] } | { flags { fec } } ] +
Syntax Description
|
ping |
need |
|
sr-mpls |
Test |
|
sr-ipv4-prefix |
IP |
|
fec-type |
Type |
|
igp |
Kind |
|
isis |
ISIS |
|
bgp |
BGP |
|
generic |
Generic |
|
repeat |
(Optional) Repeat |
|
count |
(Optional) Repeat |
|
size |
(Optional) Packet |
|
size |
(Optional) Datagram |
|
sweep |
(Optional) Sweep |
|
min-size |
(Optional) |
|
max-size |
(Optional) |
|
increment |
(Optional) Sweep |
|
timeout |
(Optional) Timeout |
|
seconds |
(Optional) Timeout |
|
interval |
(Optional) Send |
|
milliseconds |
(Optional) Send |
|
destination |
(Optional) Destination |
|
addr-start |
(Optional) Destination |
|
addr-end |
(Optional) Destination |
|
addr-incr-mask |
(Optional) Destination |
|
addr-incr |
(Optional) Destination |
|
source |
(Optional) Source |
|
addr |
(Optional) Source |
|
exp |
(Optional) EXP |
|
exp-value |
(Optional) EXP |
|
pad |
(Optional) Pad |
|
pattern |
(Optional) Pad |
|
ttl |
(Optional) Time |
|
ttl |
(Optional) TTL |
|
verbose |
(Optional) verbose |
|
reply |
(Optional) Reply |
|
mode |
(Optional) Reply |
|
reply-mode-ipv4 |
(Optional) Send |
|
router-alert |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
control-channel |
(Optional) Send |
|
no-reply |
(Optional) Send |
|
dscp |
(Optional) DSCP |
|
dscp-bits |
(Optional) Differentiated |
|
af11 |
(Optional) Match |
|
af12 |
(Optional) Match |
|
af13 |
(Optional) Match |
|
af21 |
(Optional) Match |
|
af22 |
(Optional) Match |
|
af23 |
(Optional) Match |
|
af31 |
(Optional) Match |
|
af32 |
(Optional) Match |
|
af33 |
(Optional) Match |
|
af41 |
(Optional) Match |
|
af42 |
(Optional) Match |
|
af43 |
(Optional) Match |
|
cs1 |
(Optional) Match |
|
cs2 |
(Optional) Match |
|
cs3 |
(Optional) Match |
|
cs4 |
(Optional) Match |
|
cs5 |
(Optional) Match |
|
cs6 |
(Optional) Match |
|
cs7 |
(Optional) Match |
|
default |
(Optional) Match |
|
ef |
(Optional) Match |
|
pad-tlv |
(Optional) Reply |
|
force-explicit-null |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
dsmap |
(Optional) Request |
|
hashkey |
(Optional) Downstream |
|
none |
(Optional) Hash |
|
hash-ipv4 |
(Optional) IPv4 |
|
bitmap |
(Optional) Hash |
|
bitmap-size |
(Optional) Multipath |
|
flags |
(Optional) Flag |
|
fec |
(Optional) Request |
Command Mode
/exec
[no] platform insert module <module_num> [ { linecard { N9K-X9516v | N9K-X9532v | N9K-X9536v | N9K-X9548v | N9K-X9564v | N9K-C9316D-GX | N9K-C9364D-GX2A } } ] [ asic_mode <uri0> ]
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
platform |
Platform specific commands |
|
insert |
Insert a module |
|
module |
insert a specific module |
|
module_num |
Please enter the module number |
|
linecard |
(Optional) Linecard module |
|
N9K-X9516v |
(Optional) Nexus 9000v 16 port Ethernet Module |
|
N9K-X9532v |
(Optional) Nexus 9000v 32 port Ethernet Module |
|
N9K-X9536v |
(Optional) Nexus 9000v 36 port Ethernet Module |
|
N9K-X9548v |
(Optional) Nexus 9000v 48 port Ethernet Module |
|
N9K-X9564v |
(Optional) Nexus 9000v 64 port Ethernet Module |
|
N9K-C9316D-GX |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
N9K-C9364D-GX2A |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
asic_mode |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
uri0 |
(Optional) specify asic model file |
Command Mode
/exec
[no] platform name <s0> vsan <i0>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
platform |
Platform Object Registration |
|
name |
Name of the Platform |
|
s0 |
Platform name string |
|
vsan |
VSAN id of the platform |
|
i0 |
VSAN number |
Command Mode
/exec/configure/fcs-register
platform proactive-cc forwarding [ incremental <timer-incremental> ] [ fulldb <timer-fulldb> ] | no platform proactive-cc forwarding
Syntax Description
|
no |
Negate a command or set its defaults |
|
platform |
Platform configuration commands |
|
proactive-cc |
Proactive Consistency Checker |
|
forwarding |
Forwarding |
|
incremental |
(Optional) Configure Incremental timer value |
|
timer-incremental |
(Optional) Timer value in seconds |
|
fulldb |
(Optional) Configure Fulldb timer value |
|
timer-fulldb |
(Optional) Timer value in seconds |
Command Mode
/exec/configure
{ platform | hardware } rate-limiter span-egress <rate> [ module <module> ] | no { platform | hardware } rate-limiter span-egress [ <rate> ] [ module <module> ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
platform |
Platform configuration commands |
|
hardware |
Hardware Internal Information |
|
rate-limiter |
Configure Rate-Limiter for packets forwarded |
|
span-egress |
SPAN/ERSPAN egress packets |
|
rate |
value in kbit per sec |
|
module |
(Optional) Specify a module number |
|
module |
(Optional) Specify a module number |
Command Mode
/exec/configure
platform vnic scheme { sequential | mac-encoded }
Syntax Description
|
platform |
Platform specific commands |
|
vnic |
Virtual Network Interface Card |
|
scheme |
Virtual Network Interface Card allocation scheme |
|
sequential |
Sequential allocation of VNICs to linecard modules |
|
mac-encoded |
MAC address encoded allocation of VNICs to linecard modules |
Command Mode
/exec
pnp startup-vlan <vlan> | no pnp startup-vlan [ <vlan> ]
Syntax Description
|
no |
disable pnp startup vlan configured. default value is vlan 1 |
|
pnp |
plug and play |
|
startup-vlan |
PnP startup-vlan |
|
vlan |
PNP vlan id. Default vlan is 1 |
Command Mode
/exec/configure
[no] police { { [ cir ] { <cir-val> [ bps | kbps | mbps | gbps ] | percent <cir-perc> } [ [ bc ] { <committed-burst> [ bytes | kbytes | mbytes | ms | us ] } ] [ pir { <pir-val> [ bps2 | kbps2 | mbps2 | gbps2 | pps2 ] | percent <pir-perc> } [ [ be ] { <extended-burst> [ bytes2 | kbytes2 | mbytes2 | ms2 | us2 | packets2 ] } ] ] [ conform { transmit | set-prec-transmit { <prec-val> | <prec-enum> } | set-dscp-transmit { <dscp-val> | <dscp-enum> } | set-cos-transmit <cos-val> | set-discard-class-transmit <disc-class-val> | set-qos-transmit <qos-grp-val> | set-mpls-exp-imposition-transmit <exp-value-imp> | set-mpls-exp-topmost-transmit <exp-value-top> } [ exceed { drop1 | set <exc-frm-field> <exc-to-field> table cir-markdown-map | set-prec-transmit1 { <prec-val1> | <prec-enum1> } | set-dscp-transmit1 { <dscp-val1> | <dscp-enum1> } | set-cos-transmit1 <cos-val1> | set-discard-class-transmit1 <disc-class-val1> | set-qos-transmit1 <qos-grp-val1> | set-mpls-exp-imposition-transmit1 <exp-value-imp1> | set-mpls-exp-topmost-transmit1 <exp-value-top1> } ] [ violate { drop2 | set <vio-frm-field> <vio-to-field> table2 pir-markdown-map | set-prec-transmit2 { <prec-val2> | <prec-enum2> } | set-dscp-transmit2 { <dscp-val2> | <dscp-enum2> } | set-cos-transmit2 <cos-val2> | set-discard-class-transmit2 <disc-class-val2> | set-qos-transmit2 <qos-grp-val2> | set-mpls-exp-imposition-transmit2 <exp-value-imp2> | set-mpls-exp-topmost-transmit2 <exp-value-top2> } ] ] } | aggregate <policer-name> }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
police |
police |
|
cir |
(Optional) Specify committed information rate |
|
bc |
(Optional) Specify committed burst |
|
percent |
Specify rate as percentage of interface data-rate |
|
cir-perc |
Percentage |
|
pir-perc |
(Optional) Percentage |
|
pir |
(Optional) Specify peak information rate |
|
be |
(Optional) Specify extended burst (for 1R3C meter) |
|
bps |
(Optional) Bits per second |
|
kbps |
(Optional) Kilo bits per second |
|
mbps |
(Optional) Mega bits per second |
|
gbps |
(Optional) Giga bits per second |
|
bps2 |
(Optional) Bits per second |
|
kbps2 |
(Optional) Kilo Bits per second |
|
mbps2 |
(Optional) Mega Bits per second |
|
gbps2 |
(Optional) Giga Bits per second |
|
pps2 |
(Optional) Packets per second |
|
bytes |
(Optional) Bytes |
|
kbytes |
(Optional) Kilo bytes |
|
mbytes |
(Optional) Mega bytes |
|
us |
(Optional) Micro second(s) |
|
ms |
(Optional) Milli second(s) |
|
bytes2 |
(Optional) Bytes |
|
kbytes2 |
(Optional) Kilo Bytes |
|
mbytes2 |
(Optional) Mega Bytes |
|
ms2 |
(Optional) Milli seconds |
|
us2 |
(Optional) Micro seconds |
|
packets2 |
(Optional) Packets |
|
conform |
(Optional) Specify a conform action |
|
exceed |
(Optional) Specify a exceed action |
|
violate |
(Optional) Specify a violate action |
|
transmit |
(Optional) Transmit packet |
|
drop1 |
(Optional) Drop packet |
|
drop2 |
(Optional) Drop packet |
|
set-prec-transmit |
(Optional) Set precedence and send it |
|
set-prec-transmit1 |
(Optional) Set precedence and send it |
|
set-prec-transmit2 |
(Optional) Set precedence and send it |
|
prec-val |
(Optional) Precedence value |
|
prec-val1 |
(Optional) Precedence value |
|
prec-val2 |
(Optional) Precedence value |
|
prec-enum |
(Optional) |
|
prec-enum1 |
(Optional) |
|
prec-enum2 |
(Optional) |
|
set-dscp-transmit |
(Optional) Set dscp and send it |
|
set-dscp-transmit1 |
(Optional) Set dscp and send it |
|
set-dscp-transmit2 |
(Optional) Set dscp and send it |
|
dscp-val |
(Optional) DSCP value |
|
dscp-val1 |
(Optional) DSCP value |
|
dscp-val2 |
(Optional) DSCP value |
|
dscp-enum |
(Optional) |
|
dscp-enum1 |
(Optional) |
|
dscp-enum2 |
(Optional) |
|
set-cos-transmit |
(Optional) Set cos and send it |
|
set-cos-transmit1 |
(Optional) Set cos and send it |
|
set-cos-transmit2 |
(Optional) Set cos and send it |
|
cos-val |
(Optional) new cos value |
|
cos-val1 |
(Optional) new cos value |
|
cos-val2 |
(Optional) new cos value |
|
set-discard-class-transmit |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-discard-class-transmit1 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-discard-class-transmit2 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
disc-class-val |
(Optional) new discard-class value |
|
disc-class-val1 |
(Optional) new discard-class value |
|
disc-class-val2 |
(Optional) new discard-class value |
|
set-qos-transmit |
(Optional) Set qos-group and send it |
|
set-qos-transmit1 |
(Optional) Set qos-group and send it |
|
set-qos-transmit2 |
(Optional) Set qos-group and send it |
|
qos-grp-val |
(Optional) QoS group value |
|
qos-grp-val1 |
(Optional) QoS group value |
|
qos-grp-val2 |
(Optional) QoS group value |
|
set-mpls-exp-imposition-transmit |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-mpls-exp-imposition-transmit1 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-mpls-exp-imposition-transmit2 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
exp-value-imp |
(Optional) MPLS imposition value |
|
exp-value-imp1 |
(Optional) MPLS imposition value |
|
exp-value-imp2 |
(Optional) MPLS imposition value |
|
set-mpls-exp-topmost-transmit |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-mpls-exp-topmost-transmit1 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-mpls-exp-topmost-transmit2 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
exp-value-top |
(Optional) MPLS topmost value |
|
exp-value-top1 |
(Optional) MPLS topmost value |
|
exp-value-top2 |
(Optional) MPLS topmost value |
|
set |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
exc-frm-field |
(Optional) |
|
exc-to-field |
(Optional) |
|
vio-frm-field |
(Optional) |
|
vio-to-field |
(Optional) |
|
table |
(Optional) Set using the table-map |
|
table2 |
(Optional) Set using the table-map |
|
cir-markdown-map |
(Optional) Markdown map table name for exceed action |
|
pir-markdown-map |
(Optional) Markdown map table name for violate action |
|
aggregate |
Choose aggregate policer for current class |
|
policer-name |
Enter aggregate-policer name |
Command Mode
/exec/configure/policy-map/class
[no] police [ { { [ cir ] { <cir-val> [ <opt_kbps_mbps_gbps_pps_cir> ] | percent <cir-perc> } } { [ { [ bc ] <bc-val> [ <opt_kbytes_mbytes_gbytes_bc> ] } ] } { [ { pir { <pir> [ <opt_kbps_mbps_gbps_pps_pir> ] | percent1 <pir-perc> } } [ { [ be ] <be-val> [ <opt_kbytes_mbytes_gbytes_be> ] } ] ] } { [ { conform { <opt_drop_transmit_conform> | { set-cos-transmit <set-cos-val> } | { set-dscp-transmit { <set-dscp-val> | <opt_set_dscp> } } | { set-prec-transmit { <set-prec-val> | <opt_set_prec> } } } } [ { exceed { <opt_drop_transmit_exceed> | { set dscp1 dscp2 table cir-markdown-map } } } ] [ { violate { <opt_drop_transmit_violate> | { set1 dscp3 dscp4 table1 pir-markdown-map } } } ] ] } } ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
police |
Police |
|
cir |
(Optional) Specify committed information rate |
|
opt_kbps_mbps_gbps_pps_cir |
(Optional) Units |
|
percent |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
pir |
(Optional) Specify peak information rate |
|
opt_kbps_mbps_gbps_pps_pir |
(Optional) Units |
|
percent1 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
be |
(Optional) Specify extended burst |
|
opt_kbytes_mbytes_gbytes_be |
(Optional) Units |
|
bc |
(Optional) Specify committed burst |
|
opt_kbytes_mbytes_gbytes_bc |
(Optional) Units |
|
conform |
(Optional) Specify a conform action |
|
opt_drop_transmit_conform |
(Optional) Set the action |
|
set-cos-transmit |
(Optional) Set conform action cos val |
|
set-cos-val |
(Optional) 802.1Q Class of Service value |
|
set-dscp-transmit |
(Optional) Set conform action dscp val |
|
set-dscp-val |
(Optional) DSCP value |
|
opt_set_dscp |
(Optional) |
|
set-prec-transmit |
(Optional) Set conform action precedence val |
|
set-prec-val |
(Optional) IP Precedence value |
|
opt_set_prec |
(Optional) |
|
exceed |
(Optional) Specify a exceed action |
|
opt_drop_transmit_exceed |
(Optional) Set the action |
|
set |
(Optional) Set exceed action to cir-markdown-map |
|
dscp1 |
(Optional) Exceed from field |
|
dscp2 |
(Optional) Exceed to field |
|
table |
(Optional) To specify table name |
|
cir-markdown-map |
(Optional) Well known markdown map |
|
violate |
(Optional) Specify a violate action |
|
opt_drop_transmit_violate |
(Optional) Set the action |
|
set1 |
(Optional) Set violate action to pir-markdown-map |
|
dscp3 |
(Optional) Violate from field |
|
dscp4 |
(Optional) Violate to field |
|
table1 |
(Optional) To specify table name |
|
pir-markdown-map |
(Optional) Well known markdown map |
Command Mode
/exec/configure/pmap/class
[no] police [ { { [ cir ] { <cir-val> [ <opt_kbps_mbps_gbps_pps_cir> ] | percent <cir-perc> } } { [ { [ bc ] <bc-val> [ <opt_kbytes_mbytes_gbytes_bc> ] } ] } { [ { pir { <pir> [ <opt_kbps_mbps_gbps_pps_pir> ] | percent1 <pir-perc> } } [ { [ be ] <be-val> [ <opt_kbytes_mbytes_gbytes_be> ] } ] ] } { [ { conform { <opt_drop_transmit_conform> | { set-cos-transmit <set-cos-val> } | { set-dscp-transmit { <set-dscp-val> | <opt_set_dscp> } } | { set-prec-transmit { <set-prec-val> | <opt_set_prec> } } } } [ { exceed { <opt_drop_transmit_exceed> | { set dscp1 dscp2 table cir-markdown-map } } } ] [ { violate { <opt_drop_transmit_violate> | { set1 dscp3 dscp4 table1 pir-markdown-map } } } ] ] } } ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
police |
Police |
|
cir |
(Optional) Specify committed information rate |
|
opt_kbps_mbps_gbps_pps_cir |
(Optional) Units |
|
percent |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
pir |
(Optional) Specify peak information rate |
|
opt_kbps_mbps_gbps_pps_pir |
(Optional) Units |
|
percent1 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
be |
(Optional) Specify extended burst |
|
opt_kbytes_mbytes_gbytes_be |
(Optional) Units |
|
bc |
(Optional) Specify committed burst |
|
opt_kbytes_mbytes_gbytes_bc |
(Optional) Units |
|
conform |
(Optional) Specify a conform action |
|
opt_drop_transmit_conform |
(Optional) Set the action |
|
set-cos-transmit |
(Optional) Set conform action cos val |
|
set-cos-val |
(Optional) 802.1Q Class of Service value |
|
set-dscp-transmit |
(Optional) Set conform action dscp val |
|
set-dscp-val |
(Optional) DSCP value |
|
opt_set_dscp |
(Optional) |
|
set-prec-transmit |
(Optional) Set conform action precedence val |
|
set-prec-val |
(Optional) IP Precedence value |
|
opt_set_prec |
(Optional) |
|
exceed |
(Optional) Specify a exceed action |
|
opt_drop_transmit_exceed |
(Optional) Set the action |
|
set |
(Optional) Set exceed action to cir-markdown-map |
|
dscp1 |
(Optional) Exceed from field |
|
dscp2 |
(Optional) Exceed to field |
|
table |
(Optional) To specify table name |
|
cir-markdown-map |
(Optional) Well known markdown map |
|
violate |
(Optional) Specify a violate action |
|
opt_drop_transmit_violate |
(Optional) Set the action |
|
set1 |
(Optional) Set violate action to pir-markdown-map |
|
dscp3 |
(Optional) Violate from field |
|
dscp4 |
(Optional) Violate to field |
|
table1 |
(Optional) To specify table name |
|
pir-markdown-map |
(Optional) Well known markdown map |
Command Mode
/exec/configure/pmap/class
[no] police { { [ cir ] { <cir-val> [ bps | kbps | mbps | gbps | pps ] | percent <cir-perc> } [ [ bc ] { <committed-burst> [ bytes | kbytes | mbytes | ms | us | packets ] } ] [ pir { <pir-val> [ bps2 | kbps2 | mbps2 | gbps2 | pps2 ] | percent <pir-perc> } [ [ be ] { <extended-burst> [ bytes2 | kbytes2 | mbytes2 | ms2 | us2 | packets2 ] } ] ] [ conform { transmit | set-prec-transmit { <prec-val> | <prec-enum> } | set-dscp-transmit { <dscp-val> | <dscp-enum> } | set-cos-transmit <cos-val> | set-discard-class-transmit <disc-class-val> | set-qos-transmit <qos-grp-val> | set-mpls-exp-imposition-transmit <exp-value-imp> | set-mpls-exp-topmost-transmit <exp-value-top> } ] [ exceed { transmit1 | drop1 | set <exc-frm-field> <exc-to-field> table cir-markdown-map | set-prec-transmit1 { <prec-val1> | <prec-enum1> } | set-dscp-transmit1 { <dscp-val1> | <dscp-enum1> } | set-cos-transmit1 <cos-val1> | set-discard-class-transmit1 <disc-class-val1> | set-qos-transmit1 <qos-grp-val1> | set-mpls-exp-imposition-transmit1 <exp-value-imp1> | set-mpls-exp-topmost-transmit1 <exp-value-top1> } ] [ violate { drop2 | set <vio-frm-field> <vio-to-field> table2 pir-markdown-map | set-prec-transmit2 { <prec-val2> | <prec-enum2> } | set-dscp-transmit2 { <dscp-val2> | <dscp-enum2> } | set-cos-transmit2 <cos-val2> | set-discard-class-transmit2 <disc-class-val2> | set-qos-transmit2 <qos-grp-val2> | set-mpls-exp-imposition-transmit2 <exp-value-imp2> | set-mpls-exp-topmost-transmit2 <exp-value-top2> } ] } | aggregate <policer-name> }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
police |
police |
|
cir |
(Optional) Specify committed information rate |
|
bc |
(Optional) Specify committed burst |
|
percent |
Specify rate as percentage of interface data-rate |
|
cir-perc |
Percentage |
|
pir-perc |
(Optional) Percentage |
|
pir |
(Optional) Specify peak information rate |
|
be |
(Optional) Specify extended burst (for 1R3C meter) |
|
bps |
(Optional) Bits per second |
|
kbps |
(Optional) Kilo bits per second |
|
mbps |
(Optional) Mega bits per second |
|
gbps |
(Optional) Giga bits per second |
|
pps |
(Optional) Packets per second |
|
bps2 |
(Optional) Bits per second |
|
kbps2 |
(Optional) Kilo Bits per second |
|
mbps2 |
(Optional) Mega Bits per second |
|
gbps2 |
(Optional) Giga Bits per second |
|
pps2 |
(Optional) Packets per second |
|
bytes |
(Optional) Bytes |
|
kbytes |
(Optional) Kilo bytes |
|
mbytes |
(Optional) Mega bytes |
|
us |
(Optional) Micro second(s) |
|
ms |
(Optional) Milli second(s) |
|
packets |
(Optional) Packets |
|
bytes2 |
(Optional) Bytes |
|
kbytes2 |
(Optional) Kilo Bytes |
|
mbytes2 |
(Optional) Mega Bytes |
|
ms2 |
(Optional) Milli seconds |
|
us2 |
(Optional) Micro seconds |
|
packets2 |
(Optional) Packets |
|
conform |
(Optional) Specify a conform action |
|
exceed |
(Optional) Specify a exceed action |
|
violate |
(Optional) Specify a violate action |
|
transmit |
(Optional) Transmit packet |
|
transmit1 |
(Optional) Transmit packet |
|
drop1 |
(Optional) Drop packet |
|
drop2 |
(Optional) Drop packet |
|
set-prec-transmit |
(Optional) Set precedence and send it |
|
set-prec-transmit1 |
(Optional) Set precedence and send it |
|
set-prec-transmit2 |
(Optional) Set precedence and send it |
|
prec-val |
(Optional) Precedence value |
|
prec-val1 |
(Optional) Precedence value |
|
prec-val2 |
(Optional) Precedence value |
|
prec-enum |
(Optional) |
|
prec-enum1 |
(Optional) |
|
prec-enum2 |
(Optional) |
|
set-dscp-transmit |
(Optional) Set dscp and send it |
|
set-dscp-transmit1 |
(Optional) Set dscp and send it |
|
set-dscp-transmit2 |
(Optional) Set dscp and send it |
|
dscp-val |
(Optional) DSCP value |
|
dscp-val1 |
(Optional) DSCP value |
|
dscp-val2 |
(Optional) DSCP value |
|
dscp-enum |
(Optional) |
|
dscp-enum1 |
(Optional) |
|
dscp-enum2 |
(Optional) |
|
set-cos-transmit |
(Optional) Set cos and send it |
|
set-cos-transmit1 |
(Optional) Set cos and send it |
|
set-cos-transmit2 |
(Optional) Set cos and send it |
|
cos-val |
(Optional) new cos value |
|
cos-val1 |
(Optional) new cos value |
|
cos-val2 |
(Optional) new cos value |
|
set-discard-class-transmit |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-discard-class-transmit1 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-discard-class-transmit2 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
disc-class-val |
(Optional) new discard-class value |
|
disc-class-val1 |
(Optional) new discard-class value |
|
disc-class-val2 |
(Optional) new discard-class value |
|
set-qos-transmit |
(Optional) Set qos-group and send it |
|
set-qos-transmit1 |
(Optional) Set qos-group and send it |
|
set-qos-transmit2 |
(Optional) Set qos-group and send it |
|
qos-grp-val |
(Optional) QoS group value |
|
qos-grp-val1 |
(Optional) QoS group value |
|
qos-grp-val2 |
(Optional) QoS group value |
|
set-mpls-exp-imposition-transmit |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-mpls-exp-imposition-transmit1 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-mpls-exp-imposition-transmit2 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
exp-value-imp |
(Optional) MPLS imposition value |
|
exp-value-imp1 |
(Optional) MPLS imposition value |
|
exp-value-imp2 |
(Optional) MPLS imposition value |
|
set-mpls-exp-topmost-transmit |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-mpls-exp-topmost-transmit1 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
set-mpls-exp-topmost-transmit2 |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
exp-value-top |
(Optional) MPLS topmost value |
|
exp-value-top1 |
(Optional) MPLS topmost value |
|
exp-value-top2 |
(Optional) MPLS topmost value |
|
set |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
exc-frm-field |
(Optional) |
|
exc-to-field |
(Optional) |
|
vio-frm-field |
(Optional) |
|
vio-to-field |
(Optional) |
|
table |
(Optional) Set using the table-map |
|
table2 |
(Optional) Set using the table-map |
|
cir-markdown-map |
(Optional) Markdown map table name for exceed action |
|
pir-markdown-map |
(Optional) Markdown map table name for violate action |
|
aggregate |
Choose aggregate policer for current class |
|
policer-name |
Enter aggregate-policer name |
Command Mode
/exec/configure/policy-map/class
[no] policer
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
policer |
Flow rate limiter installed in hardware |
Command Mode
/exec/configure/nbm-flow-policy/attr
[no] policer
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
policer |
Flow rate limiter installed in hardware |
Command Mode
/exec/configure/nbm-vrf/nbm-flow-policy/attr
[no] policy-map [ type qos ] [ match-first ] <pmap-name-qos>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
policy-map |
Configure a policy map |
|
type |
(Optional) Specify the type of this policy-map |
|
qos |
(Optional) Qos policy |
|
match-first |
(Optional) Take the action for the first class that matches |
|
pmap-name-qos |
Policy-map name (alphanumeric) |
Command Mode
/exec/configure
[no] policy-map type control-plane <pmap-name>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
policy-map |
Configure a policy map |
|
type |
Specify the type of this policy-map |
|
control-plane |
Control-Plane |
|
pmap-name |
Policy-map name (alphanumeric) |
Command Mode
/exec/configure
[no] policy-map type network-qos <pmap-name-nq>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
policy-map |
Configure a policy map |
|
type |
Specify the type of this policy-map |
|
network-qos |
Network QoS policy |
|
pmap-name-nq |
Policy-map name |
Command Mode
/exec/configure
[no] policy-map type queuing [ match-first ] <pmap-name-que>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
policy-map |
Configure a policy map |
|
type |
Specify the type of this policy-map |
|
queuing |
Queuing policy |
|
match-first |
(Optional) Take the action for the first class that matches |
|
pmap-name-que |
Policy-map name (alphanumeric) |
Command Mode
/exec/configure
[no] policy { <cfg-pol-name> | <unknown-pol-name> }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
policy |
NBM Flow policy |
|
cfg-pol-name |
Policy name |
|
unknown-pol-name |
Policy name |
Command Mode
/exec/configure/nbm-flow-policy
policy { { dynamic identity <device-id> } | { static sgt <sgt> [ trusted ] } } | no policy static | no policy dynamic
Syntax Description
|
policy |
Enable and define policy to be applied |
|
dynamic |
apply to authorization server for policy |
|
identity |
specify identity of peer for authorization request |
|
device-id |
peer's device-id |
|
static |
configure static policy |
|
sgt |
SGT tag for pkts from this device |
|
sgt |
sgt value |
|
trusted |
(Optional) specify trust state of the link |
Command Mode
/exec/configure/cts-manual
[no] policy <pol-name>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
policy |
Identifying name for policy with max 128 characters |
|
pol-name |
Configure Policy name |
Command Mode
/exec/configure/sr/te
[no] policy { <cfg-pol-name> | <unknown-pol-name> }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
policy |
NBM Flow policy |
|
cfg-pol-name |
Policy name |
|
unknown-pol-name |
Policy name |
Command Mode
/exec/configure/nbm-vrf/nbm-flow-policy
pop [ <name> ]
Syntax Description
|
pop |
pop mode from stack or restore from name |
|
name |
(Optional) name |
Command Mode
/global
port-channel bfd destination <dest-ip> | no port-channel bfd destination [ <dest-ip> ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
bfd |
BFD parameters |
|
destination |
Configure IP address of BFD peer |
|
dest-ip |
BFD peer IPv4 address |
Command Mode
/exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p
port-channel bfd start <start-timer-value> | no port-channel bfd start [ <start-timer-value> ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
bfd |
BFD parameters |
|
start |
Start timer timeout value |
|
start-timer-value |
BFD start timer timeout value in seconds (default off) |
Command Mode
/exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p
port-channel bfd track-member-link | no port-channel bfd track-member-link
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
bfd |
Enable BFD |
|
track-member-link |
Enable per-member-link BFD on the port-channel interface |
Command Mode
/exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p
port-channel fast-convergence | no port-channel fast-convergence
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
fast-convergence |
Enable/Disable port-channel fast convergence |
Command Mode
/exec/configure
port-channel hash-distribution <type> | no port-channel hash-distribution [ <type> ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
hash-distribution |
Configure port-channel hash-distribution |
|
type |
adaptive/fixed (default adaptive) |
Command Mode
/exec/configure/
port-channel limit | no port-channel limit
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure the maximum number of supported vPCs |
|
limit |
limit to 244 vPCs |
Command Mode
/exec/configure/vpc-domain
port-channel load-balance <bndl_hash> <bndl_sel> <encap> [ rotate <po-lb-rotate-range> ] [ symmetric ] | no port-channel load-balance [ <bndl_hash> <bndl_sel> <encap> [ rotate <po-lb-rotate-range> ] [ symmetric ] ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
load-balance |
Configure port-channel load balance |
|
bndl_hash |
bundle hash |
|
bndl_sel |
bundle select |
|
encap |
encapsulation |
|
rotate |
(Optional) offset the hash-input |
|
po-lb-rotate-range |
(Optional) offset the hash-input |
|
symmetric |
(Optional) symmetric load balancing |
Command Mode
/exec/configure
port-channel load-balance1 ethernet <algorithm> [ symmetric ] | no port-channel load-balance1 ethernet [ <algorithm> [ symmetric ] ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
load-balance1 |
Configure port-channel load balance |
|
ethernet |
Ethernet port-channel |
|
algorithm |
Configure port-channel load balance |
|
symmetric |
(Optional) symmetric load balancing |
Command Mode
/exec/configure
port-channel load-balance2 resilient | no port-channel load-balance2 resilient
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
load-balance2 |
Configure port-channel load balance |
|
resilient |
Configure port-channel load balance resilient mode |
Command Mode
/exec/configure
port-channel load-balance <bndl_hash> <bndl_sel> [ rotate <po-lb-rotate-range> ] [ concatenation ] [ module <module> | fex all ] [ symmetric ] | no port-channel load-balance [ <bndl_hash> <bndl_sel> [ rotate <po-lb-rotate-range> ] [ concatenation ] [ module <module> | fex all ] [ symmetric ] ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
load-balance |
Configure port-channel load balance |
|
bndl_hash |
bundle hash |
|
bndl_sel |
bundle select |
|
rotate |
(Optional) offset the hash-input |
|
po-lb-rotate-range |
(Optional) offset the hash-input |
|
concatenation |
(Optional) enable/disable concatenation |
|
module |
(Optional) Specify a module number |
|
module |
(Optional) Specify a module number |
|
fex |
(Optional) FEX devices |
|
all |
(Optional) Permit all FEX to configure port-channel LB |
|
symmetric |
(Optional) symmetric load balancing |
Command Mode
/exec/configure
port-channel load-defer <load-defer-timeout> | no port-channel load-defer [ <load-defer-timeout> ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
load-defer |
Load defer time interval |
|
load-defer-timeout |
Load defer time interval in seconds (default 120 seconds) |
Command Mode
/exec/configure/
port-channel port hash-distribution <type> | no port-channel port hash-distribution [ <type> ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
port |
Configure port-channel port hash-distribution |
|
hash-distribution |
Configure port-channel port hash-distribution |
|
type |
adaptive/fixed (default adaptive) |
Command Mode
/exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p
port-channel port load-defer | no port-channel port load-defer
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
port |
Configure port-channel load-defer for member ports |
|
load-defer |
Configure port-channel load-defer |
Command Mode
/exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p
port-channel scale-fanout | no port-channel scale-fanout
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-channel |
Configure port channel parameters |
|
scale-fanout |
Enable/disable port-channel scale-fanout when ports span more than 16 ASIC units |
Command Mode
/exec/configure
{ port-group <name> } | { no port-group <name> }
Syntax Description
|
no |
Negate a command or set its defaults |
|
port-group |
ITD port group |
|
name |
ITD port group name |
Command Mode
/exec/configure/itd
[no] port-license [ acquire ]
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
port-license |
Enable port activation license |
|
acquire |
(Optional) Acquire port activation license |
Command Mode
/exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext
[no] port-license [ acquire ]
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
port-license |
Enable port activation license |
|
acquire |
(Optional) Acquire port activation license |
Command Mode
/exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext
port-parameters
Syntax Description
|
port-parameters |
Clock port configuration |
Command Mode
/exec/configure/clock-if
[no] port-profile [ type <typeval> ] { <profilename> | <s0> }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
port-profile |
Configure a port-profile |
|
profilename |
Enter the name of the profile |
|
s0 |
Enter the name of the profile |
|
type |
(Optional) configure type of the profile |
|
typeval |
(Optional) |
Command Mode
/exec/configure
[no] port-recovery-interval <val>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
port-recovery-interval |
Time interval to send recovery probes,Unit:Second |
|
val |
Port recovery interval value in seconds |
Command Mode
/exec/configure/configngoamloopdetection
[no] port-type <type>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
port-type |
Identifies port facing type |
|
type |
Facing port-type |
Command Mode
/exec/configure/if-eth-non-member /exec/configure/if-port-channel /exec/configure/if-ethernet-all /exec/configure/if-ethernet-p2p /exec/configure/if-ether-sub-p2p
[no] port <port-value>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
port |
Application port number server |
|
port-value |
port value |
Command Mode
/exec/configure/itd-dg-node
{ port <sport> <dport> }
Syntax Description
|
port |
L4 port info |
|
sport |
Source port |
|
dport |
Destination port |
Command Mode
/exec/configure/configngoamccpayload
{ no port | port <value> }
Syntax Description
|
no |
|
|
port |
Port on which to listen |
|
value |
Max port value |
Command Mode
/exec/configure/config-twamp-srvr
{ { [ no ] port <i0> } | { no port } }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
port |
Specify port on which local radius server listens |
|
i0 |
Radius server port (default is 1700) |
Command Mode
/exec/configure/locsvr-da-radius
{ port { destination | source } <port> } | { no port { destination | source } }
Syntax Description
|
no |
Negate a command or set its defaults |
|
port |
specify flow port address |
|
source |
specify flow source port address |
|
destination |
specify flow destination port address |
|
port |
port number |
Command Mode
/exec/configure/configngoamprofileflow
[no] port <port-range> type { ethernet | fc [ breakout ] }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
port |
Configure a port |
|
port-range |
Enter a port range |
|
type |
Configure a port type |
|
ethernet |
Ethernet Port |
|
fc |
FC Port |
|
breakout |
(Optional) Breakout Subtype |
Command Mode
/exec/configure/slot
[no] port usb disable
Syntax Description
|
no |
(Optional) Negate a command |
|
port |
disable USB port(s) |
|
usb |
mount USB drive |
|
disable |
disables USB drive |
Command Mode
/exec/configure
[no] postcard-telemetry exporter <exportername>
Syntax Description
|
postcard-telemetry |
Enable/Disable postcard telemetry configuration |
|
exporter |
Define a events Exporter |
|
exportername |
Name of event Exporter |
Command Mode
/exec/configure/config-postcard
[no] postcard-telemetry flow-profile
Syntax Description
|
postcard-telemetry |
Enable/Disable postcard telemetry configuration |
|
flow-profile |
Define a POSTCARD flow-profile |
Command Mode
/exec/configure/config-postcard
[no] postcard-telemetry monitor <monitorname>
Syntax Description
|
postcard-telemetry |
Enable/Disable postcard telemetry configuration |
|
monitor |
Define a POSTCARD Monitor |
|
monitorname |
Name of POSTCARD Monitor |
Command Mode
/exec/configure/config-postcard
[no] postcard-telemetry queue-profile [ <queue_profilename> | queue-profile-default ]
Syntax Description
|
postcard-telemetry |
Enable/Disable postcard telemetry configuration |
|
queue-profile |
Define a POSTCARD queue_profile |
|
queue_profilename |
(Optional) Name of POSTCARD queue_profile |
|
queue-profile-default |
(Optional) Queue Profile Default Configuration |
Command Mode
/exec/configure/config-postcard
[no] postcard-telemetry system monitor <monitorname>
Syntax Description
|
system |
global config |
|
postcard-telemetry |
postcard global settings |
|
monitor |
postcard Monitor to be applied |
|
monitorname |
postcard Monitor to be applied |
Command Mode
/exec/configure/config-postcard
[no] postcard-telemetry watchlist ip <watchlistname>
Syntax Description
|
postcard-telemetry |
Enable/Disable postcard telemetry configuration |
|
watchlist |
Define a POSTCARD watchlist |
|
ip |
Configure POSTCARD IP watchlist |
|
watchlistname |
Name of POSTCARD watchlist |
Command Mode
/exec/configure/config-postcard
[no] power efficient-ethernet auto
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
power |
Configure EEE for the port |
|
efficient-ethernet |
Configure Energy Efficient Ethernet (EEE) |
|
auto |
Auto negotiate EEE |
Command Mode
/exec/configure/if-ethernet-all /exec/configure/if-eth-base
[no] power efficient-ethernet sleep threshold aggressive
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
power |
Configure EEE for the port |
|
efficient-ethernet |
Configure Energy Efficient Ethernet (EEE) |
|
sleep |
EEE LPI sleep configuration |
|
threshold |
EEE LPI sleep threshold |
|
aggressive |
Enable/ Disable EEE LPI aggressive sleep mode |
Command Mode
/exec/configure/if-ethernet-all /exec/configure/if-eth-base
{ power inline { <port-mode-never> | <port-mode> [ max <wattage> ] } } | { no power inline { <port-mode-never> | <port-mode> } }
Syntax Description
|
no |
Negate a command or set its defaults |
|
power |
Power over Ethernet |
|
port-mode-never |
configure POE port mode |
|
port-mode |
configure POE port mode |
|
max |
(Optional) Configure the max power per interface |
|
wattage |
(Optional) milli-watts |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
{ power inline default_consumption <wattage> } | { no power inline default_consumption }
Syntax Description
|
no |
Negate a command or set its defaults |
|
power |
Power over Ethernet |
|
default_consumption |
POE port default consumption |
|
wattage |
milli-watts |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
{ power inline police action <police-action> } | { no power inline police action }
Syntax Description
|
no |
Negate a command or set its defaults |
|
power |
Power over Ethernet |
|
police |
Configure POE port police parameters |
|
action |
Configure action in port when power allocation exceeds |
|
police-action |
configure POE port action |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
{ power inline port priority <port-priority> } | { no power inline port priority <port-priority> }
Syntax Description
|
no |
Negate a command or set its defaults |
|
power |
Power over Ethernet |
|
port |
Configure POE port parameters |
|
priority |
Configure the priority for the port |
|
port-priority |
configure POE port priority |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] power redundancy-mode combined
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
power |
Configure power supply |
|
redundancy-mode |
Configure power supply redundancy mode |
|
combined |
Configure power supply redundancy mode as combined |
Command Mode
/exec/configure
[no] power redundancy-mode combined force
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
power |
Configure power supply |
|
redundancy-mode |
Configure power supply redundancy mode |
|
combined |
Configure power supply redundancy mode as combined |
|
force |
Force combined mode without prompting |
Command Mode
/exec/configure
[no] power redundancy-mode insrc-redundant
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
power |
Configure power supply |
|
redundancy-mode |
Configure power supply redundancy mode |
|
insrc-redundant |
Configure power supply redundancy mode as grid/AC input source redundant |
Command Mode
/exec/configure
[no] power redundancy-mode ps-redundant
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
power |
Configure power supply |
|
redundancy-mode |
Configure power supply redundancy mode |
|
ps-redundant |
Configure power supply redundancy mode as PS redundant |
Command Mode
/exec/configure
[no] poweroff { module <lem-aware-module> | <s0> <santa-cruz-range> }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
poweroff |
Power off a module in the switch |
|
module |
enter a module number |
|
lem-aware-module |
please enter the module number |
|
s0 |
Power off a specific xbar |
|
santa-cruz-range |
please enter the xbar number |
Command Mode
/exec/configure
{ { no | default } precision | precision { milliseconds | microseconds } }
Syntax Description
|
no |
|
|
precision |
milliseconds |
|
default |
Set a command to its defaults |
|
precision |
Set precision of measurement |
|
microseconds |
Precision microseconds |
|
milliseconds |
Precision milliseconds |
Command Mode
/exec/configure/ip-sla/jitter
[no] preempt
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
preempt |
Enable preemption of lower priority master |
Command Mode
/exec/configure/if-eth-any/vrrp
[no] preempt | preempt
Syntax Description
|
no |
Negate a command or set its defaults |
|
preempt |
Enable preemption of lower priority Master |
Command Mode
/exec/configure/if-eth-any/vrrpv3
[no] preempt delay | preempt delay minimum <secs>
Syntax Description
|
no |
Negate a command or set its defaults |
|
preempt |
Enable preemption of lower priority Master |
|
delay |
Wait before preempting |
|
minimum |
Delay at least this long |
|
secs |
Seconds to delay |
Command Mode
/exec/configure/if-eth-any/vrrpv3
preempt delay minimum <min-delay> reload <rel-delay> sync <sync-delay> | preempt delay reload <rel-delay> minimum <min-delay> sync <sync-delay> | preempt delay sync <sync-delay> minimum <min-delay> reload <rel-delay> | preempt delay reload <rel-delay> sync <sync-delay> minimum <min-delay> | preempt delay sync <sync-delay> reload <rel-delay> minimum <min-delay> | preempt delay minimum <min-delay> sync <sync-delay> reload <rel-delay> | preempt delay reload <rel-delay> sync <sync-delay> | preempt delay sync <sync-delay> reload <rel-delay> | preempt delay minimum <min-delay> sync <sync-delay> | preempt delay sync <sync-delay> minimum <min-delay> | preempt delay minimum <min-delay> reload <rel-delay> | preempt delay reload <rel-delay> minimum <min-delay> | preempt delay minimum <min-delay> | preempt delay reload <rel-delay> | preempt delay sync <sync-delay> | preempt | no preempt | no preempt delay [ { minimum [ <min-delay> ] [ [ reload [ <rel-delay> ] ] [ sync [ <sync-delay> ] ] | [ sync [ <sync-delay> ] ] [ reload [ <rel-delay> ] ] ] | reload [ <rel-delay> ] [ [ minimum [ <min-delay> ] ] [ sync [ <sync-delay> ] ] | [ sync [ <sync-delay> ] ] [ minimum [ <min-delay> ] ] ] | sync [ <sync-delay> ] [ [ reload [ <rel-delay> ] ] [ minimum [ <min-delay> ] ] | [ minimum [ <min-delay> ] ] [ reload [ <rel-delay> ] ] ] } ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
preempt |
Overthrow lower priority Active routers |
|
delay |
Wait before preempting |
|
minimum |
Delay at least this long |
|
min-delay |
Number of seconds for minimum delay |
|
reload |
Delay after reload |
|
rel-delay |
Number of seconds for reload delay |
|
sync |
Wait for IP redundancy clients |
|
sync-delay |
Number of seconds for sync delay |
Command Mode
/exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6
[no] preference <pref>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
preference |
Candidate path-option preference entry |
|
pref |
Path-option preference |
Command Mode
/exec/configure/sr/te/color/cndpaths
[no] preference <pref>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
preference |
Policy path-option preference entry |
|
pref |
Path-option preference |
Command Mode
/exec/configure/sr/te/pol/cndpaths
[no] preference max <pref-val>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pref-val |
maximum value |
Command Mode
/exec/configure/config-dhcp-guard
[no] preference min <pref-val>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pref-val |
maximum value |
Command Mode
/exec/configure/config-dhcp-guard
[no] prefix-priority high
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
prefix-priority |
Gives prefix priority to this address family routes |
|
high |
Set priority to high |
Command Mode
/exec/configure/router-bgp/router-bgp-af-ipv4-label
[no] prefix <ipv6-prefix>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
prefix |
Configure the SRv6 locator as an IPv6 prefix |
Command Mode
/exec/configure/sr/srv6/locators/locator
[ no | default ] { prefix-list <prfxlist-name> } { out | in }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
default |
(Optional) Inherit values from a peer template |
|
prefix-list |
Apply prefix-list |
|
prfxlist-name |
Name of prefix-list |
|
out |
Apply policy to outgoing routes |
|
in |
Apply policy to incoming routes |
Command Mode
/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
[no] prepend-pkg-opts
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
prepend-pkg-opts |
Prepend docker package runtime options |
Command Mode
/exec/configure/app-hosting-docker
[no] priority-flow-control auto-restore multiplier { <val> }
Syntax Description
|
no |
(Optional) Negate the command |
|
priority-flow-control |
pfc related commands |
|
auto-restore |
auto restore |
|
multiplier |
Auto restore multiplier |
|
val |
Auto multiplier value |
Command Mode
/exec/configure
[no] priority-flow-control fixed-restore multiplier { <val> }
Syntax Description
|
no |
(Optional) Negate the command |
|
priority-flow-control |
pfc related commands |
|
fixed-restore |
fixed restore |
|
multiplier |
Fixed restore multiplier |
|
val |
Fixed multiplier value |
Command Mode
/exec/configure
[no] priority-flow-control mode { auto | on [ send-tlv ] | off } [ force ]
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
priority-flow-control |
Enable/Disable PFC |
|
mode |
PFC Mode |
|
auto |
Set Auto Mode |
|
on |
Force PFC to On |
|
off |
Force PFC to Off |
|
force |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
send-tlv |
(Optional) Send DCBX TLV for PFC config |
Command Mode
/exec/configure/if-switching /exec/configure/if-routing /exec/configure/if-port-channel /exec/configure/if-port-channel-sub
[no] priority-flow-control override-interface mode off
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
priority-flow-control |
Global priority-flow-control settings |
|
override-interface |
Overrides interface priority-flow-control mode |
|
mode |
Priority-flow-control mode |
|
off |
Off |
Command Mode
/exec/configure
priority-flow-control recover interface <if_list> [ qos-group <qgrp-num> ] [ module <module_idx> ] [ instance <inst> ]
Syntax Description
|
priority-flow-control |
Change PFC settings |
|
recover |
Recover PFC queue from stuck state |
|
interface |
Interface |
|
if_list |
List of interfaces |
|
qos-group |
(Optional) No-drop class to be recovered |
|
qgrp-num |
(Optional) qos-group number of the no-drop class |
|
module |
(Optional) Slot/module |
|
module_idx |
(Optional) Slot/module number |
|
instance |
(Optional) ASIC Instance Number |
|
inst |
(Optional) ASIC Instance Number in Decimal |
Command Mode
/exec
priority-flow-control tah-recover interface <if_list> [ qos-group <qos> ] [ module <module> ]
Syntax Description
|
priority-flow-control |
Change PFC settings |
|
tah-recover |
Recover PFC queue from stuck state |
|
interface |
Interface |
|
if_list |
List of interfaces |
|
qos-group |
(Optional) No-drop class to be recovered |
|
qos |
(Optional) qos-group number of the no-drop class |
|
module |
(Optional) Slot/module |
|
module |
(Optional) Slot/module number |
Command Mode
/exec
[no] priority-flow-control watch-dog-interval { on | off }
Syntax Description
|
no |
(Optional) Negate the command |
|
priority-flow-control |
Enable/Disable PFC |
|
watch-dog-interval |
Watch dog interval |
|
on |
Enable PFC watch-dog interval globally |
|
off |
Disable PFC watch-dog interval globally |
Command Mode
/exec/configure
[no] priority-flow-control watch-dog-interval { on [ disable-action ] [ interface-multiplier <multiplier-val> ] | off }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
priority-flow-control |
Enable/Disable PFC |
|
watch-dog-interval |
Watch dog interval |
|
on |
PFC watch-dog interval to On |
|
disable-action |
(Optional) Only generate syslog for stuck queue, no action |
|
interface-multiplier |
(Optional) Shutdown multiplier value |
|
multiplier-val |
(Optional) Shutdown mutlipler value |
|
off |
PFC watch-dog interval to Off |
Command Mode
/exec/configure/if-switching /exec/configure/if-routing /exec/configure/if-port-channel /exec/configure/if-port-channel-sub
[no] priority-flow-control watch-dog forced { on | off }
Syntax Description
|
no |
(Optional) Negate the command |
|
priority-flow-control |
pfc related commands |
|
watch-dog |
watch dog interval |
|
forced |
Force enable watch-dog behaviour globally |
|
on |
Enable PFC watch-dog globally |
|
off |
Disable PFC watch-dog globally |
Command Mode
/exec/configure
[no] priority-flow-control watch-dog interval <interval-val>
Syntax Description
|
no |
(Optional) Negate the command |
|
priority-flow-control |
pfc related commands |
|
watch-dog |
watch dog interval |
|
interval |
Poll interval |
|
interval-val |
Watch dog interval value in ms |
Command Mode
/exec/configure
[no] priority-flow-control watch-dog shutdown-multiplier { <val> }
Syntax Description
|
no |
(Optional) Negate the command |
|
priority-flow-control |
pfc related commands |
|
watch-dog |
watch dog interval |
|
shutdown-multiplier |
Shutdown multiplier |
|
val |
Shutdown multiplier |
Command Mode
/exec/configure
priority <value> | no priority
Syntax Description
|
no |
Negate a command or set its defaults |
|
priority |
Configure Bundle priority |
|
value |
Priority value |
Command Mode
/exec/configure/anycast
[no] priority2 [ level2 <value> ]
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
priority2 |
Configure traffic class priority |
|
level2 |
(Optional) Specify level of priority |
|
value |
(Optional) Strict-priority level (1=hi 2=med 3=lo) |
Command Mode
/exec/configure/policy-map/type/queuing/class
[no] priority [ level <value> ]
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
priority |
Configure traffic class priority |
|
level |
(Optional) Specify level of priority |
|
value |
(Optional) Value of level, lower the number higher the priority |
Command Mode
/exec/configure/policy-map/type/queuing/class
{ priority <priority_value> [ forwarding-threshold lower <lower-value> upper <upper-value> ] | no priority [ forwarding-threshold ] }
Syntax Description
|
no |
Negate a command or set its defaults |
|
priority |
Configure the vr priority |
|
priority_value |
Configure the vr priority |
|
forwarding-threshold |
(Optional) Set forwarding threshold |
|
lower |
(Optional) Set lower threshold value |
|
lower-value |
(Optional) Lower threshold value |
|
upper |
(Optional) Set upper threshold value |
|
upper-value |
(Optional) Upper threshold value |
Command Mode
/exec/configure/if-eth-any/vrrp
priority <priority> [ forwarding-threshold lower <lower-value> upper <upper-value> ] | no priority [ forwarding-threshold ]
Syntax Description
|
no |
Negate a command or set its defaults |
|
priority |
Priority level |
|
priority |
Priority value |
|
forwarding-threshold |
(Optional) Set forwarding threshold |
|
lower |
(Optional) Set lower threshold value |
|
lower-value |
(Optional) Lower threshold value |
|
upper |
(Optional) Set upper threshold value |
|
upper-value |
(Optional) Upper threshold value |
Command Mode
/exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6
[no] priority | priority <val>
Syntax Description
|
no |
Negate a command or set its defaults |
|
priority |
Priority of this VRRP group |
|
val |
Priority level |
Command Mode
/exec/configure/if-eth-any/vrrpv3
[no] priority <value>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
priority |
Source priority |
|
value |
priority value, 1 (highest) 100 (default) 254 (lowest) |
Command Mode
/exec/configure/if-eth-base/fsync
[no] priority <value>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
priority |
Source priority |
|
value |
priority value, 1 (highest) 100 (default) 254 (lowest) |
Command Mode
/exec/configure/clock-if/fsync
[no] priority <value>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
priority |
Source priority |
|
value |
priority value, 1 (highest) 100 (default) 254 (lowest) |
Command Mode
/exec/configure/gnss-if/fsync
{ priority critical | no priority [ critical ] }
Syntax Description
|
no |
Negate a command or set its defaults |
|
priority |
Group priority |
|
critical |
Critical Priority (Highest) |
Command Mode
/exec/configure/nbm-vrf/nbm-flow-policy/attr/prop
{ priority critical | no priority [ critical ] }
Syntax Description
|
no |
Negate a command or set its defaults |
|
priority |
Group priority |
|
critical |
Critical Priority (Highest) |
Command Mode
/exec/configure/nbm-flow-policy/attr/prop
[no] private-vlan <pvlan-type>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
private-vlan |
Configure a private VLAN |
|
pvlan-type |
PVLAN Type |
Command Mode
/exec/configure/vlan
{ private-vlan association [ { add | remove } ] <secondary_vlans> } | { no private-vlan association [ <secondary_vlans> ] }
Syntax Description
|
private-vlan |
Configure a private VLAN |
|
association |
Add association between private VLANs |
|
add |
(Optional) Add a VLAN to private VLAN list |
|
remove |
(Optional) Remove a VLAN from private VLAN list |
|
no |
Negate a command or set its defaults |
|
secondary_vlans |
VLAN IDs of the private VLANs to be configured |
Command Mode
/exec/configure/vlan
{ private-vlan mapping [ { add | remove } ] <secondary_vlans> } | { no private-vlan mapping [ <secondary_vlans> ] }
Syntax Description
|
private-vlan |
Configure a private VLAN |
|
mapping |
Set the private VLAN interface mapping |
|
add |
(Optional) Add a VLAN to private VLAN list |
|
remove |
(Optional) Remove a VLAN from private VLAN list |
|
no |
Negate a command or set its defaults |
|
secondary_vlans |
Secondary VLAN IDs of the private VLAN interface mapping |
Command Mode
/exec/configure/if-vlan
private-vlan synchronize
Syntax Description
|
private-vlan |
Set private-vlan synchronization |
|
synchronize |
Synchronize vlans |
Command Mode
/exec/configure/spanning-tree/mst/configuration
probe-interval <probeinterval-val> | no probe-interval
Syntax Description
|
no |
Negate a command or set its defaults |
|
probe-interval |
OpenFlow controller probe interval timer (default is 180 seconds) |
|
probeinterval-val |
probe interval timer value in secs |
Command Mode
/exec/configure/openflow/switch/sub-switch
probe-interval <probeinterval-val> | no probe-interval
Syntax Description
|
no |
Negate a command or set its defaults |
|
probe-interval |
OpenFlow controller probe interval timer (default is 180 seconds) |
|
probeinterval-val |
probe interval timer value in secs |
Command Mode
/exec/configure/openflow/switch
[no] probe <probe-id-icmp> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id-icmp |
Service mode |
|
frequency |
(Optional) Frequency in seconds |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
|
ip |
(Optional) ip address for probe |
|
ip-addr |
(Optional) IP4 prefix in format i.i.i.i |
Command Mode
/exec/configure/itd-dg-node
[no] probe { icmp | <l4-proto> <port-num> [ control <status> ] | http get [ <url-name> ] | dns host <host-name> | ctp } [ frequency <freq-num> | timeout <timeout> | retry-down-count <down-count> | retry-up-count <up-count> | source-interface <src-intf> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
Probe for service health-checks |
|
icmp |
icmp probe |
|
l4-proto |
tcp/udp probes |
|
port-num |
Port number |
|
control |
(Optional) Control protocol |
|
status |
(Optional) Control protocol status |
|
http |
http-get probe |
|
get |
Host name/Target address |
|
url-name |
(Optional) Specify only the user input text/filename. http://<node-ip>/<user input> |
|
dns |
dns probe |
|
host |
DNS host |
|
host-name |
DNS Target IP Address or Hostname |
|
ctp |
ctp probe |
|
frequency |
(Optional) Frequency in seconds |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
down-count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
|
source-interface |
(Optional) Source interface for probe |
|
src-intf |
(Optional) Source loopback interface |
Command Mode
/exec/configure/epbr/svc /exec/configure/epbr/fwd-svc /exec/configure/epbr/reverse-svc
[no] probe { icmp | <l4-proto> <port-num> [ control <status> ] | http get [ <url-name> ] | dns host <host-name> | ctp } [ frequency <freq-num> | timeout <timeout> | retry-down-count <down-count> | retry-up-count <up-count> | source-interface <src-intf> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
Probe for service health-checks |
|
icmp |
icmp probe |
|
l4-proto |
tcp/udp probes |
|
port-num |
Port number |
|
control |
(Optional) Control protocol |
|
status |
(Optional) Control protocol status |
|
http |
http-get probe |
|
get |
Host name/Target address |
|
url-name |
(Optional) Specify only the user input text/filename. http://<node-ip>/<user input> |
|
dns |
dns probe |
|
host |
DNS host |
|
host-name |
DNS Target IP Address or Hostname |
|
ctp |
ctp probe |
|
frequency |
(Optional) Frequency in seconds |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
down-count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
|
source-interface |
(Optional) Source interface for probe |
|
src-intf |
(Optional) Source loopback interface |
Command Mode
/exec/configure/epbr-sess/fwd-svc /exec/configure/epbr-sess/reverse-svc
[no] probe <probe-id-icmp> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id-icmp |
Service mode |
|
frequency |
(Optional) Frequency in seconds |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
|
ip |
(Optional) ip address for probe |
|
ip-addr |
(Optional) IP4 prefix in format i.i.i.i |
Command Mode
/exec/configure/itd-dg-node-standby
[no] probe <probe-id-icmp> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id-icmp |
Service mode |
|
frequency |
(Optional) Frequency in seconds |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
Command Mode
/exec/configure/itd-device-group
[no] probe <probe-id-http> get [ <url-name> | cache | frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id-http |
Service mode |
|
get |
Host name/Target address |
|
url-name |
(Optional) Specify only the user input text/filename. http://<node-ip>/<user input> |
|
cache |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
frequency |
(Optional) Frequency |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
|
ip |
(Optional) ip address for probe |
|
ip-addr |
(Optional) IP4 prefix in format i.i.i.i |
Command Mode
/exec/configure/itd-dg-node-standby
[no] probe <probe-id-http> get [ <url-name> | cache | frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id-http |
Service mode |
|
get |
Host name/Target address |
|
url-name |
(Optional) Specify only the user input text/filename. http://<node-ip>/<user input> |
|
cache |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
frequency |
(Optional) Frequency |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
|
ip |
(Optional) ip address for probe |
|
ip-addr |
(Optional) IP4 prefix in format i.i.i.i |
Command Mode
/exec/configure/itd-dg-node
[no] probe <probe-id-http> get [ <url-name> | cache | frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id-http |
Service mode |
|
get |
Host name/Target address |
|
url-name |
(Optional) Specify only the user input text/filename. http://<node-ip>/<user input> |
|
cache |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
frequency |
(Optional) Frequency |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
Command Mode
/exec/configure/itd-device-group
[no] probe <probe-id-dns> host <host-name> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id-dns |
Service mode |
|
host |
Host name/Target address |
|
host-name |
DNS Target IP Address or Hostname |
|
frequency |
(Optional) Frequency |
|
freq-num |
(Optional) Frequency |
|
timeout |
(Optional) Timeout |
|
timeout |
(Optional) Timeout |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
|
ip |
(Optional) ip address for probe |
|
ip-addr |
(Optional) IP4 prefix in format i.i.i.i |
Command Mode
/exec/configure/itd-dg-node
[no] probe <probe-id-dns> host <host-name> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id-dns |
Service mode |
|
host |
Host name/Target address |
|
host-name |
DNS Target IP Address or Hostname |
|
frequency |
(Optional) Frequency in seconds |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
|
ip |
(Optional) ip address for probe |
|
ip-addr |
(Optional) IP4 prefix in format i.i.i.i |
Command Mode
/exec/configure/itd-dg-node-standby
[no] probe <probe-id-dns> host <host-name> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id-dns |
Service mode |
|
host |
Host name/Target address |
|
host-name |
DNS Target IP Address or Hostname |
|
frequency |
(Optional) Frequency in seconds |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
Command Mode
/exec/configure/itd-device-group
[no] probe <probe-id> port <port-num> [ control <status> ] [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id |
Service mode |
|
port |
Port |
|
port-num |
Port number |
|
control |
(Optional) control protocol |
|
status |
(Optional) control protocol status |
|
frequency |
(Optional) Frequency in seconds |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
|
ip |
(Optional) ip address for probe |
|
ip-addr |
(Optional) IP4 prefix in format i.i.i.i |
Command Mode
/exec/configure/itd-dg-node-standby
[no] probe <probe-id> port <port-num> [ control <status> ] [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id |
Service mode |
|
port |
Port |
|
port-num |
Port number |
|
control |
(Optional) control protocol |
|
status |
(Optional) control protocol status |
|
frequency |
(Optional) Frequency in seconds |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
|
ip |
(Optional) ip address for probe |
|
ip-addr |
(Optional) IP4 prefix in format i.i.i.i |
Command Mode
/exec/configure/itd-dg-node
[no] probe <probe-id> port <port-num> [ control <status> ] [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> | retry-up-count <up-count> ] +
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
probe-id |
Service mode |
|
port |
Port |
|
port-num |
Port number |
|
control |
(Optional) control protocol |
|
status |
(Optional) control protocol status |
|
frequency |
(Optional) Frequency in seconds |
|
freq-num |
(Optional) Frequency in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
timeout |
(Optional) Timeout in seconds |
|
retry-down-count |
(Optional) Retry-count when node goes down |
|
count |
(Optional) Count |
|
retry-up-count |
(Optional) Retry-count when node comes back up |
|
up-count |
(Optional) Count |
Command Mode
/exec/configure/itd-device-group
[no] probe track <track-id>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
track |
track id |
|
track-id |
track id |
Command Mode
/exec/configure/itd-dg-node-standby
[no] probe track <track-id>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
Probe for service health-checks |
|
track |
track id |
|
track-id |
track id |
Command Mode
/exec/configure/epbr /exec/configure/epbr/fwd-svc /exec/configure/epbr/reverse-svc
[no] probe track <track-id>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
Probe for service health-checks |
|
track |
track id |
|
track-id |
track id |
Command Mode
/exec/configure/epbr-sess/fwd-svc /exec/configure/epbr-sess/reverse-svc
[no] probe track <track-id>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
track |
track id |
|
track-id |
track id |
Command Mode
/exec/configure/itd-session-dg-node
[no] probe track <track-id>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
probe |
ITD probe |
|
track |
track id |
|
track-id |
track id |
Command Mode
/exec/configure/itd-dg-node
[no] profile <profilename>
Syntax Description
|
profile |
Specify the profile to be applied |
|
profilename |
profile name to be applied |
Command Mode
/exec/configure/nfm-system
{ profile <pid> | no profile }
Syntax Description
|
no |
Negate a command or set its defaults |
|
profile |
NGOAM profile to use |
|
pid |
NGOAM profile id |
Command Mode
/exec/configure/configngoamconnectcheck
[no] profile <profilename>
Syntax Description
|
profile |
Specify the profile to be applied |
|
profilename |
profile name to be applied |
Command Mode
/exec/configure/analytics/system
[no] profile <profile-name>
Syntax Description
|
no |
(Optional) Negate the command |
|
profile |
Packet Drop Profile |
|
profile-name |
Profile name |
Command Mode
/exec/configure/pkt-drop
[no] propagate-sgt
Syntax Description
|
propagate-sgt |
Enable SGT propagation from this port (the default use the no form to disable) |
Command Mode
/exec/configure/cts-dot1x /exec/configure/cts-manual
[no] { protected | unprotected }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
protected |
Candidate path-option protected |
|
unprotected |
Candidate path-option unprotected |
Command Mode
/exec/configure/sr/te/pol/cndpaths/pref/constraint/sgmnt
[no] { protected | unprotected }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
protected |
Candidate path-option protected |
|
unprotected |
Candidate path-option unprotected |
Command Mode
/exec/configure/sr/te/color/cndpaths/pref/constraint/sgmnt
{ proto <proto-id> }
Syntax Description
|
proto |
Protocol |
|
proto-id |
IANA Protocol id |
Command Mode
/exec/configure/configngoamccpayload
protocol-version { <10> | <13> | negotiate } | no protocol-version
Syntax Description
|
no |
Negate a command or set its defaults |
|
protocol-version |
Set OpenFlow protocol version |
|
10 |
Use only OF 1.0 protocol to connect to controller |
|
13 |
Use only OF 1.3 protocol to connect to controller |
|
negotiate |
Negotiate protocol with controller |
Command Mode
/exec/configure/openflow/switch
protocol-version { <10> | <13> | negotiate } | no protocol-version
Syntax Description
|
no |
Negate a command or set its defaults |
|
protocol-version |
Set OpenFlow protocol version |
|
10 |
Use only OF 1.0 protocol to connect to controller |
|
13 |
Use only OF 1.3 protocol to connect to controller |
|
negotiate |
Negotiate protocol with controller |
Command Mode
/exec/configure/openflow/switch/sub-switch
[no] protocol <proto> [ prefix-list <pflist-name> ]
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
proto |
|
|
pflist-name |
(Optional) Name of the prefix-list to be matched |
Command Mode
/exec/configure/config-snoop-policy
{ protocol <num> } | { no protocol }
Syntax Description
|
no |
Negate a command or set its defaults |
|
protocol |
specify flow protocol number |
|
num |
flow protocol number |
Command Mode
/exec/configure/configngoamprofileflow
[no] proxy <proxy-server> [ port <proxy-port> ] [ username <proxy-username>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
proxy |
Set proxy server, ipv4/ipv6/hostname |
|
port |
(Optional) Set proxy server port |
|
username |
(Optional) Set proxy authentication username |
|
proxy-server |
IPv4 or IPv6 address or DNS name of proxy server |
|
proxy-port |
(Optional) Proxy port number |
|
proxy-username |
(Optional) Proxy username |
Command Mode
/exec/configure/telemetry/destination-group/host
[no] ptp
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp acl-redirect
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
acl-redirect |
ACL based ptp forwarding |
Command Mode
/exec/configure
[no] ptp announce interval { <log-seconds> | smpte-2059-2 <smpte-log-seconds> | aes67 <aes-log-seconds> }
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
announce |
announce |
|
interval |
interval |
|
log-seconds |
log seconds |
|
smpte-2059-2 |
SMPTE-2059-2 |
|
smpte-log-seconds |
SMPTE-2059-2 log seconds |
|
aes67 |
AES67-2015 |
|
aes-log-seconds |
AES67-2015 log seconds |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp announce interval { <log-seconds> | smpte-2059-2 <smpte-log-seconds> | aes67 <aes-log-seconds> }
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
announce |
announce |
|
interval |
interval |
|
log-seconds |
log seconds |
|
smpte-2059-2 |
SMPTE-2059-2 |
|
smpte-log-seconds |
SMPTE-2059-2 log seconds |
|
aes67 |
AES67-2015 |
|
aes-log-seconds |
AES67-2015 log seconds |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp announce timeout { <val> | smpte-2059-2 <smpte-val> | aes67 <aes-val> }
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
announce |
announce |
|
timeout |
timeout |
|
smpte-2059-2 |
SMPTE-2059-2 |
|
aes67 |
AES67-2015 |
|
val |
|
|
smpte-val |
SMPTE-2059-2 val |
|
aes-val |
AES67-2015 val |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp asymmetric-delay { forward-path | reverse-path } <delay-value> | no ptp asymmetric-delay
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
asymmetric-delay |
configurtion to compensate asymmetric delay |
|
forward-path |
asymmetric delay direction from master to slave |
|
reverse-path |
asymmetric delay direction from slave to master |
|
delay-value |
compensation time for asymmetric delay [1 - 512000000 ns] |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
ptp clock-identity <mac-address> | no ptp clock-identity
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
clock-identity |
clock-identity |
|
mac-address |
Mac Address |
Command Mode
/exec/configure
[no] ptp clock-sync auto
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
clock-sync |
clock-sync |
|
auto |
auto adjust frequency |
Command Mode
/exec/configure
[no] ptp clock periodic-update [ interval <val> ]
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
clock |
Enable updating system time to 1588 time. |
|
periodic-update |
Enable clock update periodically. |
|
interval |
(Optional) interval |
|
val |
(Optional) system time update frequency in seconds. |
Command Mode
/exec/configure
[no] ptp convergence-time [ <val> ]
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
convergence-time |
Convergence time for Grandmaster capable node |
|
val |
(Optional) convergence-time |
Command Mode
/exec/configure
[no] ptp correction-range <threshold-value>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
correction-range |
set correction range threshold value |
|
threshold-value |
correction threshold (ns) [-value, +value], default 100000 (100 us) |
Command Mode
/exec/configure
[no] ptp correction-range logging
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
correction-range |
set correction range threshold value |
|
logging |
enable logging for corrections exceeding threshold value |
Command Mode
/exec/configure
[no] ptp correction hardware
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
correction |
Corrections for PTP |
|
hardware |
Frequency correction from hardware or software |
Command Mode
/exec/configure
[no] ptp cost <cost>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
cost |
Cost associated with the interface |
|
cost |
Cost |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp delay-request minimum interval { <log-seconds> | smpte-2059-2 <smpte-log-seconds> | aes67 <aes-log-seconds> }
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
delay-request |
delay-request |
|
minimum |
minimum |
|
interval |
interval |
|
smpte-2059-2 |
SMPTE-2059-2 |
|
aes67 |
AES67-2015 |
|
log-seconds |
log seconds |
|
smpte-log-seconds |
SMPTE-2059-2 log seconds |
|
aes-log-seconds |
AES67-2015 log seconds |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp delay-request minimum interval { <log-seconds> | smpte-2059-2 <smpte-log-seconds> | aes67 <aes-log-seconds> }
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
delay-request |
delay-request |
|
minimum |
minimum |
|
interval |
interval |
|
smpte-2059-2 |
SMPTE-2059-2 |
|
aes67 |
AES67-2015 |
|
log-seconds |
log seconds |
|
smpte-log-seconds |
SMPTE-2059-2 log seconds |
|
aes-log-seconds |
AES67-2015 log seconds |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp delay tolerance { reverse-path | mean-path } <threshold-value> | no ptp delay tolerance { reverse-path | mean-path }
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
delay |
delay mean-path/reverse path variation |
|
tolerance |
Tolerance for variation |
|
reverse-path |
Tolerance for reverse-path-delay variation |
|
mean-path |
Tolerance for mean-path-delay variation |
|
threshold-value |
Threshold percentage value [1.0 - 100.0] |
Command Mode
/exec/configure
[no] ptp destination-mac { forwardable | non-forwardable } rx-no-match { accept | drop | follow-rx }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
destination-mac |
PTP packets destination MAC |
|
forwardable |
Forwardable MAC |
|
non-forwardable |
Non-forwardable MAC |
|
rx-no-match |
RX packet not matching dest MAC configuration |
|
accept |
Accept packet and respond based on configuration |
|
drop |
Drop packet and do not respond respond |
|
follow-rx |
Accept packet and respond based on received packet |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp device-type { boundary-clock | generalized-ptp | ordinary-clock-grandmaster }
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
device-type |
ptp device-type |
|
boundary-clock |
boundary-clock |
|
generalized-ptp |
Generalized PTP |
|
ordinary-clock-grandmaster |
Ordinary clock Grandmaster |
Command Mode
/exec/configure
[no] ptp domain <domain-val>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
domain |
ptp clock domain |
|
domain-val |
Enter domain value |
Command Mode
/exec/configure
[no] ptp domain <domain-val>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
domain |
ptp domain to be associated with interface |
|
domain-val |
Enter configured domain value, default 0 |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp domain <domain-val> clock-accuracy-threshold <threshold-value>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
domain |
ptp clock domain |
|
domain-val |
Domain value, default is 0 |
|
clock-accuracy-threshold |
Domain clock accuracy threshold |
|
threshold-value |
Domain clock accuracy threshold value, default is 254 |
Command Mode
/exec/configure
[no] ptp domain <domain-val> clock-class-threshold <threshold-value>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
domain |
ptp clock domain |
|
domain-val |
Domain value, default is 0 |
|
clock-class-threshold |
Domain clock class threshold |
|
threshold-value |
Domain clock class threshold value, default is 248 |
Command Mode
/exec/configure
[no] ptp domain <domain-val> priority <priority-val>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
domain |
ptp clock domain |
|
domain-val |
Domain value, default is 0 |
|
priority |
Domain priority |
|
priority-val |
Domain priority value, default is 255 |
Command Mode
/exec/configure
[no] ptp enhanced-client-scale
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
enhanced-client-scale |
Enable scaling of PTP multicast clients |
Command Mode
/exec/configure
[no] ptp forward-version1
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
forward-version1 |
Forward PTPv1 packets |
Command Mode
/exec/configure
ptp grandmaster-capable | no ptp grandmaster-capable [ convergence-time <val> ]
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
grandmaster-capable |
Grandmaster capability |
|
convergence-time |
(Optional) Convergence time in seconds |
|
val |
(Optional) convergence |
Command Mode
/exec/configure
[no] ptp management
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
management |
Management packet support |
Command Mode
/exec/configure
[no] ptp master { <ipv4> | <ipv6> } [ negotiation-schema <name> ]
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
master |
master |
|
ipv4 |
IPv4 address of master |
|
negotiation-schema |
(Optional) PTP unicast-negotiation schema |
|
name |
(Optional) Name of schema |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp mean-path-delay <threshold-value>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
mean-path-delay |
set mean-path-delay threshold value |
|
threshold-value |
mean-path-delay threshold (ns), default 1000000000 (1 sec) |
Command Mode
/exec/configure
ptp multi-domain | no ptp multi-domain
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
multi-domain |
Configure ptp multi-domain |
Command Mode
/exec/configure
[no] ptp multi-domain transition-attributes priority1 <priority1-value>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
multi-domain |
Configure ptp multi-domain |
|
transition-attributes |
ptp multi-domain priority domain conversion attributes |
|
priority1 |
domain conversion priority1 value |
|
priority1-value |
Enter domain priority1 value, default 255 |
Command Mode
/exec/configure
[no] ptp multi-domain transition-attributes priority2 <priority2-value>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
multi-domain |
Configure ptp multi-domain |
|
transition-attributes |
ptp multi-domain priority domain conversion attributes |
|
priority2 |
domain conversion priority2 value |
|
priority2-value |
Enter domain priority2 value, default 255 |
Command Mode
/exec/configure
[no] ptp neighbor propagation-delay-threshold <nseconds>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
neighbor |
ptp neighbor |
|
propagation-delay-threshold |
GPTP propagation delay threshold |
|
nseconds |
Interval in nano-seconds |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp notification type gm-change
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
notification |
Define the PTP notification. |
|
type |
Notification type |
|
gm-change |
Notification for changes in PTP Grand-master |
Command Mode
/exec/configure
[no] ptp notification type high-correction [ interval { immediate | { <value> [ periodic-notification { enable | disable } ] } } ]
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
notification |
Define the PTP notification. |
|
type |
Notification type |
|
high-correction |
Corrections which is crossing the threshold value. |
|
interval |
(Optional) Wait time between two successive notifications. |
|
immediate |
(Optional) Notification will be sent immediately after the event |
|
value |
(Optional) Duration value granularity is in seconds. |
|
periodic-notification |
(Optional) Define how notification will be sent. |
|
enable |
(Optional) Always send notification with configured <duration> period. |
|
disable |
(Optional) Notification will be sent only when any event occurance. |
Command Mode
/exec/configure
[no] ptp notification type parent-change
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
notification |
Define the PTP notification. |
|
type |
Notification type |
|
parent-change |
Notification for changes in PTP parent |
Command Mode
/exec/configure
[no] ptp notification type port-state-change [ category { all | master-slave-only } ] [ interval { immediate | <intv-val> [ periodic-notification { enable | disable } ] } ]
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
notification |
Define the PTP notification. |
|
type |
Notification type |
|
port-state-change |
Notification for changes in PTP port state |
|
category |
(Optional) Define categories that need to be notified |
|
all |
(Optional) All PTP port state changes |
|
master-slave-only |
(Optional) Notify PTP port state changes to Master/Slave only |
|
interval |
(Optional) Interval between two successive notifications |
|
immediate |
(Optional) Notification will be sent immediately after the event |
|
intv-val |
(Optional) Interval value in seconds |
|
periodic-notification |
(Optional) Define how notification will be sent |
|
enable |
(Optional) Always send notification with configured interval period |
|
disable |
(Optional) Notification will be sent only if some event occurred during the interval |
Command Mode
/exec/configure
[no] ptp offload
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
offload |
Allows increasing number of PTP sessions per system by offloading some timers to linecard |
Command Mode
/exec/configure
[no] ptp pdelay-req-interval <val>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
pdelay-req-interval |
Log mean peer delay request interval |
|
val |
value |
Command Mode
/exec/configure
[no] ptp priority1 <val>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
priority1 |
priority1 |
|
val |
priority1 |
Command Mode
/exec/configure
[no] ptp priority2 <val>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
priority2 |
Priority2 |
|
val |
priority2 |
Command Mode
/exec/configure
[no] ptp profile-override
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
profile-override |
Allow override of some PTP profile parameters on interface |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp role { dynamic | master | slave }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
role |
role |
|
dynamic |
dynamic (bmca-assigned) |
|
master |
master-only |
|
slave |
slave-only |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp slave { <ipv4> | <ipv6> }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
slave |
slave |
|
ipv4 |
IPv4 address of slave |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp source { <src-ip> | <src-ipv6> } [ vrf { <vrf-name> | <vrf-cfg-name> } ]
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
source |
source IP address |
|
src-ip |
IPv4 address (A.B.C.D) of source |
|
vrf |
THIS KEYWORD OR VARIABLE IS NOT SUPPORTED |
|
vrf-name |
(Optional) vrf to be used for hellos |
|
vrf-cfg-name |
(Optional) Configurable VRF name |
Command Mode
/exec/configure
[no] ptp sync interval { <log-seconds> | smpte-2059-2 <smpte-log-seconds> | aes67 <aes-log-seconds> }
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
sync |
sync |
|
interval |
interval |
|
smpte-2059-2 |
SMPTE-2059-2 |
|
aes67 |
AES67-2015 |
|
log-seconds |
log seconds |
|
smpte-log-seconds |
SMPTE-2059-2 log seconds |
|
aes-log-seconds |
AES67-2015 log seconds |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp sync interval { <log-seconds> | smpte-2059-2 <smpte-log-seconds> | aes67 <aes-log-seconds> }
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
sync |
sync |
|
interval |
interval |
|
smpte-2059-2 |
SMPTE-2059-2 |
|
aes67 |
AES67-2015 |
|
log-seconds |
log seconds |
|
smpte-log-seconds |
SMPTE-205902 log seconds |
|
aes-log-seconds |
AES67-2015 log seconds |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp transmission { multicast | unicast [ negotiation-schema <name> ] }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
transmission |
unicast/multicast transmission |
|
multicast |
multicast |
|
unicast |
unicast |
|
negotiation-schema |
(Optional) PTP unicast-negotiation schema |
|
name |
(Optional) Name of schema |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp transport { ipv4 | ipv6 | ethernet }
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
transport |
transport |
|
ipv4 |
ipv4 |
|
ipv6 |
ipv6 |
|
ethernet |
ethernet |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp ucast-source { <src-ip> | <src-ipv6> } [ vrf { <vrf-name> | <vrf-cfg-name> } ]
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
ucast-source |
source IP address for ucast messages |
|
src-ip |
IPv4 address (A.B.C.D) of source |
|
vrf |
(Optional) vrf to be used for hello messages |
|
vrf-name |
(Optional) vrf to be used for hellos |
|
vrf-cfg-name |
(Optional) Configurable VRF name |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
[no] ptp unicast-negotiation
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
unicast-negotiation |
PTP unicast-negotiation |
Command Mode
/exec/configure
[no] ptp utc-offset <s1> [ next-leapevent <d1> <t1> new-offset <s2> ]
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
utc-offset |
UTC offset to be added to GM clock |
|
s1 |
Enter leap seconds |
|
next-leapevent |
(Optional) Time for next leap event |
|
d1 |
(Optional) YYYY-MM-DD Date (Year 2022-2099) |
|
t1 |
(Optional) HH:MM:SS Time |
|
new-offset |
(Optional) UTC offset to be added to GM clock after next leap event |
|
s2 |
(Optional) Enter leap seconds |
Command Mode
/exec/configure
[no] ptp vlan <vlan>
Syntax Description
|
ptp |
Precision Time Protocol (IEEE 1588) Subsystem |
|
vlan |
vlan |
|
vlan |
vlan |
Command Mode
/exec/configure/if-eth-base /exec/configure/if-ethernet-all
purge fcdomain fcid vsan <i0>
Syntax Description
|
purge |
Deletes unused data |
|
fcdomain |
Purge persistent FCIDs |
|
fcid |
Purge persistent FCIDs |
|
vsan |
Specify the vsan range |
|
i0 |
VSAN id range |
Command Mode
/exec
purge module <module> running-config
Syntax Description
|
purge |
Deletes unused data |
|
module |
Purge configuration for non-existent modules |
|
module |
Enter module number |
|
running-config |
purge running configuration for non-existent modules |
Command Mode
/exec
push [ <name> ]
Syntax Description
|
push |
push current mode to stack or save it under name |
|
name |
(Optional) name |
Command Mode
/global
pwd
Syntax Description
|
pwd |
View current directory |
Command Mode
/exec
[no] pwwn <wwn0> vsan <i1>
Syntax Description
|
no |
(Optional) Negate a command or set its defaults |
|
pwwn |
Device PWWN |
|
wwn0 |
PWWN of the Device |
|
vsan |
VSAN id for device |
|
i1 |
vsan id |
Command Mode
/exec/configure/dpvm-db
python [ <uri> [ <pyargs> ] + ]
Syntax Description
|
python |
run a python command/script, or enter python mode (if no arg) |
|
uri |
(Optional) path to a python file |
|
pyargs |
(Optional) python command line arguments (maximum 32) |
Command Mode
/exec
python3 [ <uri> [ <pyargs> ] + ]
Syntax Description
|
python3 |
run a python3 command/script, or enter python mode (if no arg) |
|
uri |
(Optional) path to a python file |
|
pyargs |
(Optional) python command line arguments (maximum 32) |
Command Mode
/exec
[no] python instance <inst> [ <uri> [ <pyargs> ] + ] | python instance <inst> <uri> [ <pyargs> ] +
Syntax Description
|
no |
Negate a command or set its defaults |
|
python |
run a python command/script, or enter python mode (if no arg) |
|
instance |
label with an instance number |
|
inst |
instance number |
|
uri |
(Optional) path to a python file |
|
pyargs |
(Optional) python command line arguments (maximum 32) |
Command Mode
/exec/configure
Feedback