Table Of Contents
Usage Guidelines and Restrictions
Open Caveats in Release 12.2(2)YK1
Resolved Caveats in Release 12.2(2)YK1
Manual Configuration in the Absence of CMM-Specific XML Files
Related Cisco CallManager Caveats—Release 3.2(2c) and/or Earlier
Obtaining Technical Assistance
Contacting TAC by Using the Cisco TAC Website
Release Notes for Catalyst 6500 Series and
Cisco 7600 Series Communication Media Module Software Release 12.2(2)YK1
Current Release: 12.2(2)YK1—November 14, 2002
This publication describes the features, modifications, and caveats for the Catalyst 6500 series and Cisco 7600 Series Internet Router Communication Media Module (CMM) software release 12.2(2)YK1 running Cisco IOS Release 12.1(13)E or later or Catalyst software release 7.3(1) or later.
Note For detailed installation and configuration procedures for the CMM, refer to the Catalyst 6500 Series and Cisco 7600 Series Internet Router Communication Media Module Installation and Configuration Note at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_14107.htm
Note Except where specifically differentiated, the term "Catalyst 6500 series switches" includes both Catalyst 6500 series and Catalyst 6000 series switches.
Contents
•Usage Guidelines and Restrictions
•Usage Guidelines and Restrictions
•Obtaining Technical Assistance
System Requirements
This section describes the system requirements for the CMM software release.
Hardware Supported
The supervisor engine can have an MSFC, MSFC2, or MSFC3, but the CMM does not require one for configuration or operation.
Product Number Product Description Minimum
Software Version Recommended
Software Version IOS Release Catalyst ReleaseWS-SVC-CMM
Communication Media Module
12.2(2)YK
12.2(2)YK1
12.1(13)E
7.3(1)
Software Compatibility
Software release 12.2(2)YK1 requires Cisco IOS Release 12.1(13)E or Catalyst software release 7.3(1) or later.
Orderable Software Images
Table 1 lists the software versions and applicable ordering information for the CMM software.
Table 1 Orderable Software Images
Software Version Filename Orderable Product Number 112.2(2)YK1 image
wscmm-i6s-mz
S6CMVG3-12202YK
1 Installed on system; append with "=" for spare on floppy media.
Feature Set
Table 2 lists the supported features for the CMM interface modules in software release 12.2(2)YK1.
Table 2 CMM Interface Module Supported Features
WS-SVC-CMM-6T1 Module WS-SVC-CMM-6E1 ModuleLine code—HDB33 , AMI
Frame format—with CRC4/no CRC4
MGCP:
T1-PRI
T1-CAS E&M7 Wink Start
T1-CAS E&M Delay Dial
Fax Pass-through
Cisco Fax Relay
Modem Pass-through
Music on Hold
DTMF8 , 9 Relay
G711 codec (sampling size: 10, 20, and 30 ms)
G729 codec (sampling size: 10, 20, 30, 40, 50, and 60 ms)MGCP:
E1-PRI
Fax Pass-through
Cisco Fax Relay
DTMF Relay
Modem Pass-through
Music on Hold
G711 codec (sampling size: 10, 20, and 30 ms)
G729 codec (sampling size: 10, 20, 30, 40, 50, and 60 ms)
1 B8ZS = binary 8-zero substitution
2 AMI = alternate mark inversion
3 HDB3 = high-density bipolar with three zeros
4 SF = super framing
5 ESF = extended super framing
6 CRC = cyclic redundancy check
7 E&M = ear and mouth
8 DTMF = Dual Tone Multi-Frequency
9 DTMF is supported; DTMF/MF is not supported
Usage Guidelines and Restrictions
This section provides usage guidelines and restrictions for the CMM.
•The recommended VAD setting for the CMM is off.
Caveats
These sections describe the following release caveats:
•Open Caveats in Release 12.2(2)YK1
•Resolved Caveats in Release 12.2(2)YK1
•Manual Configuration in the Absence of CMM-Specific XML Files
•Related Cisco CallManager Caveats—Release 3.2(2c) and/or Earlier
Open Caveats in Release 12.2(2)YK1
This section describes the known limitations that exist in CMM software release 12.2(2)YK1.
•After a reload with the MGCP (XML) configuration download enabled, there might be a Warning on the Console saying "Warning: Primary line clock source is not operational." Actually, the clock source line primary is configured by MGCP (XML) configuration download before and after a reload. (CSCdy33340)
•There might be a problem when fax pass-through is configured but only when a fax or modem is in close proximity to an IP or PSTN phone. Once a call is established through the gateway, one-way audio can be triggered if either the IP phone or the PSTN phone is in close proximity to an audible fax or modem. Fax or modem tones induced into the line through the handset or speakers can trigger a PCM_SWITCHOVER resulting in one-way audio from the PSTN side.
Workaround: Increase the distance between the phone and the fax/modem, or reduce the fax/modem volume. (CSCdz14789)
•There is a problem with voice activity detection (VAD) or silence suppression when these are enabled on G.729 calls only. A delay will occur on the 7935 Polycom phone with some of the T1 (CAS/PRI) or E1 (PRI) voice calls. The delay is heard in only one direction from the PSTN to the 7935 Polycom phone. The delay problem occurs with varying amounts of delay. If you experience this problem, the workaround is to turn off VAD. (CSCdz19171)
Resolved Caveats in Release 12.2(2)YK1
This section describes the resolved caveats in CMM software release 12.2(2)YK1.
•Voice calls fail on the CMM if the codec type configured is G711ULAW or G711ALAW with a 30-ms sampling rate. There is no problem when configured for 10-ms and 20-ms sampling rates. This problem is resolved in Release 12.2(2)YK1. (CSCdy23154)
•A periodic clicking sound might be heard when a call is put on hold. The workaround is to configure unicast Music on Hold instead of multicast Music on Hold. This problem is resolved in Release 12.2(2)YK1. (CSCdy49606)
•The temperature monitoring process has been optimized to reduce CPU utilization. This problem is resolved in Release 12.2(2)YK1. (CSCdy41750)
•This problem might affect G.729 calls. An intermittent delay might be heard in the PSTN-to-IP phone direction for calls originating from the PSTN to an IP phone. If you experience this problem, the workaround is to turn VAD off. This problem is resolved in Release 12.2(2)YK1. (CSCdy54786)
•The CMM temperature sensors on the baseboard should work as follows: The Sensor 1 field refers to the outtake temperature sensor, and the Sensor 2 field refers to the intake temperature sensor. However, the software "swaps" the temperature readings of the two sensors. This problem is resolved in Release 12.2(2)YK1. (CSCdy84013)
•With auto configuration, you might not be able to download the complete XML configuration file. As a result, the configuration is not done.
Workaround: Manually create the configurations on the gateway. This problem is resolved in Release 12.2(2)YK1. (CSCdy51953)
•When reconfiguring the ISDN switch type from primary-ni to primary-5ess or updating any other value with that endpoint in CCM using the gateway auto configure feature, the T1 controller gets shut down when the reconfiguration is done. As a result of the reconfiguration, the Layer 1 is deactivated.
Workaround: 1. Manually change the switch type rather than using the auto config feature. 2. Or manually do a no shut after the auto reconfiguration is done. This problem is resolved in Release 12.2(2)YK1. (CSCdz17090)
Manual Configuration in the Absence of CMM-Specific XML Files
If you do not have the CMM-specific XML files or do not want to install CMM-specific XML files, you need to perform the following configuration tasks:
Note The problem requiring manual configuration in the absence of CMM-specific XML files has been fixed in the Cisco CallManager 3.2(2c)spF-rc3 support patch. If you load that patch, you do not need to perform the following configuration tasks.
•Configure the clock source line primary and clock source line secondary under T1/E1 controllers as per your requirements. The secondary clock source is a backup for the primary clock source and the CMM supports secondary clock sources from 1 to 17. The CMM must have clock source line primary and clock source line secondary configured to avoid any clock slips.
•The default configuration for the CMM is "Cisco Fax Relay." To run "Fax pass through calls," you need to supplement the default configuration with the following two commands:
–mgcp modem pass through voip mode cisco
–no ccm fax protocol cisco
•The default configuration for "echo cancel coverage" is set to 64 ms. This default can be changed as needed under voice-port configuration.
•The default configuration for "input gain" and "output attenuation" is set to 0 db. This default can be changed as needed under voice-port configuration.
The manual configuration is lost on a reload if you set the CMM for configuration download from Cisco CallManager. If the configuration is lost, you must reconfigure it. To retain the manual configuration, disable the automatic configuration download from Cisco CallManager before doing a CMM reload.
Related Cisco CallManager Caveats—Release 3.2(2c) and/or Earlier
This section describes the related Cisco CallManager caveats in release 3.2(2c) and/or earlier releases.
Note The caveats listed below have been fixed in the Cisco CallManager 3.2(2c)spF-rc3 support patch.
•The global GW database xxxx.cnf.xml file (in the tftppath directory in Cisco CallManager) does not get updated after changes are made in the MGCP configuration GUI. To update this file, you need to restart "TFTP service" on the Cisco CallManager. (CSCdy10859)
•Adding a new gateway does not automatically create the corresponding xxxx.cnf.xml file (in the tftppath directory in Cisco CallManager). To create this file, you need to restart "TFTP service" on Cisco CallManager. (CSCdy11956)
Related Documentation
For more detailed installation and configuration information, refer to the following publications:
•Catalyst 6000 Family and Cisco 7600 Series Internet Router Communication Media Module Installation and Configuration Note
•Regulatory Compliance and Safety Information for the Catalyst 6500 Series Switches
•Catalyst 6500 Series Installation Guide
•Catalyst 6500 Series Quick Software Configuration Guide
•Catalyst 6500 Series Module Installation Guide
•Catalyst 6500 Series Software Configuration Guide
•Catalyst 6500 Series Command Reference
•Catalyst 6500 Series IOS Software Configuration Guide
•Catalyst 6500 Series IOS Command Reference
•System Message Guide—Catalyst 6500 Series, 5000 Family, 4000 Family, 2926G Series, 2948G, and 2980G Switches
•For information about MIBs, refer to
http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml
Obtaining Documentation
The following sections provide sources for obtaining documentation from Cisco Systems.
World Wide Web
You can access the most current Cisco documentation on the World Wide Web at the following sites:
Documentation CD-ROM
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or as an annual subscription.
Ordering Documentation
Cisco documentation is available in the following ways:
•Registered Cisco Direct Customers can order Cisco Product documentation from the Networking Products MarketPlace:
http://www.cisco.com/cgi-bin/order/order_root.pl
•Registered Cisco.com users can order the Documentation CD-ROM through the online Subscription Store:
http://www.cisco.com/go/subscription
•Nonregistered CCO users can order documentation through a local account representative by calling Cisco corporate headquarters (California, USA) at 408 526-7208 or, in North America, by calling 800 553-NETS(6387).
Documentation Feedback
If you are reading Cisco product documentation on the World Wide Web, you can submit technical comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco.
You can e-mail your comments to bug-doc@cisco.com.
To submit your comments by mail, for your convenience many documents contain a response card behind the front cover. Otherwise, you can mail your comments to the following address:
Cisco Systems, Inc.
Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883We appreciate your comments.
Obtaining Technical Assistance
Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools. For Cisco.com registered users, additional troubleshooting tools are available from the TAC website.
Cisco.com
Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information and resources at anytime, from anywhere in the world. This highly integrated Internet application is a powerful, easy-to-use tool for doing business with Cisco.
Cisco.com provides a broad range of features and services to help customers and partners streamline business processes and improve productivity. Through Cisco.com, you can find information about Cisco and our networking solutions, services, and programs. In addition, you can resolve technical issues with online technical support, download and test software packages, and order Cisco learning materials and merchandise. Valuable online skill assessment, training, and certification programs are also available.
Customers and partners can self-register on Cisco.com to obtain additional personalized information and services. Registered users can order products, check on the status of an order, access technical support, and view benefits specific to their relationships with Cisco.
To access Cisco.com, go to the following website:
Technical Assistance Center
The Cisco TAC website is available to all customers who need technical assistance with a Cisco product or technology that is under warranty or covered by a maintenance contract.
Contacting TAC by Using the Cisco TAC Website
If you have a priority level 3 (P3) or priority level 4 (P4) problem, contact TAC by going to the TAC website:
P3 and P4 level problems are defined as follows:
•P3—Your network performance is degraded. Network functionality is noticeably impaired, but most business operations continue.
•P4—You need information or assistance on Cisco product capabilities, product installation, or basic product configuration.
In each of the above cases, use the Cisco TAC website to quickly find answers to your questions.
To register for Cisco.com, go to the following website:
http://www.cisco.com/register/
If you cannot resolve your technical issue by using the TAC online resources, Cisco.com registered users can open a case online by using the TAC Case Open tool at the following website:
http://www.cisco.com/tac/caseopen
Contacting TAC by Telephone
If you have a priority level 1(P1) or priority level 2 (P2) problem, contact TAC by telephone and immediately open a case. To obtain a directory of toll-free numbers for your country, go to the following website:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
P1 and P2 level problems are defined as follows:
•P1—Your production network is down, causing a critical impact to business operations if service is not restored quickly. No workaround is available.
•P2—Your production network is severely degraded, affecting significant aspects of your business operations. No workaround is available.
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
CCIP, the Cisco Powered Network mark, the Cisco Systems Verified logo, Cisco Unity, Follow Me Browsing, FormShare, Internet Quotient, iQ Breakthrough, iQ Expertise, iQ FastTrack, the iQ Logo, iQ Net Readiness Scorecard, Networking Academy, ScriptShare, SMARTnet, TransPath, and Voice LAN are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All That's Possible, The Fastest Way to Increase Your Internet Quotient, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, Fast Step, GigaStack, IOS, IP/TV, LightStream, MGX, MICA, the Networkers logo, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar, SlideCast, StrataView Plus, Stratm, SwitchProbe, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.
All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0208R)
Copyright © 2002, Cisco Systems, Inc.
All rights reserved.